| OID symbolic | OID numeric | Type | Access | Description |
|---|
| pdnAdslSeltMIB | 1.3.6.1.4.1.1795.2.24.2.6.31 | | | This MIB module defines a portion of the management information base
(MIB) for managing configuration and monitoring results of SELT
(Single Ended Line Test) tests over ADSL interfaces.
At the time this MIB was defined, the IETF ADSL MIB Working does
not have any work on the 'standard' MIBs planned and/or has not produced
a schedule to address G.SELT needs. As a result, these objects may
be a `temporary' solution until MIBs/Objects are defined
meet the needs of ADSL SELT testing.
=====================================================================
== ==
== Copyright (C) 2005 Paradyne Corporation. ==
== ==
===================================================================== |
| pdnAdslSeltNotifications | 1.3.6.1.4.1.1795.2.24.2.6.31.0 | | | |
| pdnAdslSeltObjects | 1.3.6.1.4.1.1795.2.24.2.6.31.1 | | | |
| INT pdnAdslSeltWireSize | 1.3.6.1.4.1.1795.2.24.2.6.31.1.1 | INTEGER | read-write | This object permits the selection of the metric unit
to be used when reporting SELT test results.
(i.e for AWG results are in feet and for
metric/metricJapan results are in meters).
This configuration parameter applies to all the SELT
tests run in the device. |
| pdnAdslSeltTable | 1.3.6.1.4.1.1795.2.24.2.6.31.1.2 | | not-accessible | This table allows initiation/termination of
SELT Tests. |
| pdnAdslSeltEntry | 1.3.6.1.4.1.1795.2.24.2.6.31.1.2.1 | | not-accessible | Each entry represents an instance of a SELT test
currently running or ever run (since last system reset)
on an ADSL interface.
There should be entries in this table for every
active running tests and test that are in the process
of being stopped or have terminated already.
There should be no entries for ADSL interfaces that
have not run a test since last since reset; thus,
the agent should return NO_SUCH_NAME for those cases. |
| PDN pdnAdslSeltType | 1.3.6.1.4.1.1795.2.24.2.6.31.1.2.1.1 | PdnSeltTypes | not-accessible | This object is used to specify the SELT test type
that will be initiated.
If a SELT Test is already running on the ADSL interface,
writing to this object is prohibited by the agent until
the previous test is completed or terminated. |
| INT pdnAdslSeltCmd | 1.3.6.1.4.1.1795.2.24.2.6.31.1.2.1.2 | INTEGER | read-write | This object corresponds to the list of test operations
that can be performed.
The possible values are noOp(1), start(2), stop(3), or
clearResults(4).
Reading this object will always return the value 'noOp (1)'.
If SELT test is already running on an ADSL interface,
the only possible test command is 'stop (1)'.
The clearResults(4) command clears test results by removing
and entry in the pdnAdslSeltLcTable or the
pdnAdslSeltLnfTable. After the execution of this command,
the appropriate value for pdnAdslSeltStatus would be
resultsCleared(5). |
| INT pdnAdslSeltStatus | 1.3.6.1.4.1.1795.2.24.2.6.31.1.2.1.3 | INTEGER | read-only | This object provides status about any SELT test
running or ever run (since last reset) on an ADSL
interface. This object can be read by NMS managers
to determine the status of a test; that is:
inProgress (1) - if the test is currently running.
stoppedInProgress (2) - if a request to stop the test
is still in progress.
complete (3) - if the test has been run at least
once since system reset and has
completed.
notStarted (4) - if the test has not been run on
this interface since last system
reset.
resultsCleared (5) - if the entry in the test results table,
Lc or Lnf, was removed as the result
of the execution of the clearResults(4)
pdnAdslSeltCmd. |
| U32 pdnAdslSeltDuration | 1.3.6.1.4.1.1795.2.24.2.6.31.1.2.1.4 | Unsigned32 | read-write | This object provides the approximate time in Seconds that
the SELT test measurement will take.
This object should return 0 if no test is actively
running on the ADSL interface specified. |
| U32 pdnAdslSeltTimeLeft | 1.3.6.1.4.1.1795.2.24.2.6.31.1.2.1.5 | Unsigned32 | read-only | This object provides the approximate time left in Seconds
for the test running on this ADSL interface.
This object should return 0 if no test is actively
running on the ADSL interface specified. |
| pdnAdslSeltLcTable | 1.3.6.1.4.1.1795.2.24.2.6.31.1.3 | | not-accessible | This table post results for loop
characterization tests completed. |
| pdnAdslSeltLcEntry | 1.3.6.1.4.1.1795.2.24.2.6.31.1.3.1 | | not-accessible | Each entry represents the results of a loop
characterization test performed over an ADSL interface. |
| I32 pdnAdslSeltLcSegmentIndex | 1.3.6.1.4.1.1795.2.24.2.6.31.1.3.1.1 | Integer32 | not-accessible | This object indicates the index of the segment being reported.
From no segments to a possible of 10 segments could be
identified in the loop topology. |
| I32 pdnAdslSeltLcSegmentLength | 1.3.6.1.4.1.1795.2.24.2.6.31.1.3.1.2 | Integer32 | read-only | This object indicates an estimate of the segment Length
being reported |
| INT pdnAdslSeltLcSegmentGauge | 1.3.6.1.4.1.1795.2.24.2.6.31.1.3.1.3 | INTEGER | read-only | This object indicates the estimated Gauge of the segment
being reported. The gauge reported back is based on the
pdnAdslSeltWireSizeWireSize configuration parameter passed
when the test is started. |
| INT pdnAdslSeltLcSegmentType | 1.3.6.1.4.1.1795.2.24.2.6.31.1.3.1.4 | INTEGER | read-only | This object indicates the segment type being reported. |
| pdnAdslSeltLnfTable | 1.3.6.1.4.1.1795.2.24.2.6.31.1.4 | | not-accessible | This table post results for loop
noise floor tests completed. |
| pdnAdslSeltLnfEntry | 1.3.6.1.4.1.1795.2.24.2.6.31.1.4.1 | | not-accessible | Each entry represents the results of a Loop
Noise Floor test performed over an ADSL interface. |
| I32 pdnAdslSeltLnfSubCarrierIndex | 1.3.6.1.4.1.1795.2.24.2.6.31.1.4.1.1 | Integer32 | not-accessible | Identifies a row in the table based on a subcarrier.
The subcarrier index ranges from 0 to NSCus-1
(NSC is Number of Subcarriers) as specified in G.997.1
where NSCus is the higher subcarrier that can be transmitted
in the upstream direction. Please refer to the corresponding
ITU recommendation for specific values of NSCus.
The `ADSL Values for NSC' comment above lists those
recommendations. |
| I32 pdnAdslSeltLnfPeakPsd | 1.3.6.1.4.1.1795.2.24.2.6.31.1.4.1.2 | Integer32 | read-only | This object indicates the peak Psd of the tone indicated by
the sub-carrier index.
The value returned by the agent for this object is
expressed in units of 1/256 dBm. |
| I32 pdnAdslSeltLnfTotalPsd | 1.3.6.1.4.1.1795.2.24.2.6.31.1.4.1.3 | Integer32 | read-only | This object indicates the total Psd of the tone indicated by
the sub-carrier index.
The value returned by the agent for this object is
expressed in units of 1/256 dBm. |
| I32 pdnAdslSeltLnfSignalPsd | 1.3.6.1.4.1.1795.2.24.2.6.31.1.4.1.4 | Integer32 | read-only | This object indicates the signal Psd of the tone indicated by
the sub-carrier index.
The value returned by the agent for this object is
expressed in units of 1/256 dBm. |
| pdnAdslSeltAFNs | 1.3.6.1.4.1.1795.2.24.2.6.31.2 | | | |
| pdnAdslSeltConformance | 1.3.6.1.4.1.1795.2.24.2.6.31.3 | | | |
| pdnAdslSeltCompliances | 1.3.6.1.4.1.1795.2.24.2.6.31.3.1 | | | |
| pdnAdslSeltMIBCompliance | 1.3.6.1.4.1.1795.2.24.2.6.31.3.1.1 | | | The compliance statement for the entities which
implement the pdnAdslSeltMIB. |
| pdnAdslSeltGroups | 1.3.6.1.4.1.1795.2.24.2.6.31.3.2 | | | |
| pdnAdslSeltObjGroups | 1.3.6.1.4.1.1795.2.24.2.6.31.3.2.1 | | | |
| pdnAdslSeltGroup | 1.3.6.1.4.1.1795.2.24.2.6.31.3.2.1.1 | | | General configuration of SELT tests. |
| pdnAdslSeltLcGroup | 1.3.6.1.4.1.1795.2.24.2.6.31.3.2.1.2 | | | Objects related to results posted for Loop
Characterization Test. |
| pdnAdslSeltLnfGroup | 1.3.6.1.4.1.1795.2.24.2.6.31.3.2.1.3 | | | Objects related to results posted for Loop
Signal Floor Test. |
| pdnAdslSeltAfnGroups | 1.3.6.1.4.1.1795.2.24.2.6.31.3.2.2 | | | |
| pdnAdslSeltNtfyGroups | 1.3.6.1.4.1.1795.2.24.2.6.31.3.2.3 | | | |
