OPLINK-BTI-OPS-MIB

All MIBs › OPLINK-BTI-OPS-MIB

Organization: OPLINK

Last Updated: 2013-04-02

Category: Optical Networking

Description: Manages optical component status and performance for Oplink Communications BTI optical networking equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is OPLINK-BTI-OPS-MIB?

OPLINK-BTI-OPS-MIB is a vendor-specific SNMP module from Oplink Communications covering optical component status and performance for BTI-branded optical networking equipment, part of the OPSM (Optical Performance/Supervisory Module) management framework. It exposes hardware inventory data for optical modules/units, including chassis and slot placement, manufacturer name, module type, part number, serial number, manufacture and calibration dates, and firmware version, which together form a detailed hardware asset and identity picture for each optical component. Its monitoring value centers on hardware identity and firmware status: confirming which optical modules are installed, verifying firmware versions across a fleet, and tracking calibration dates that matter for optical measurement accuracy, alongside trap notifications for fault conditions. It is a vendor-specific module tied to Oplink's OPSM version 2 architecture and does not appear to depend on external standard MIBs based on the available data. It is deployed in optical transport/DWDM networks using Oplink BTI optical modules, monitored by carriers or enterprises for optical component inventory and health, where an OPLINK-BTI-OPS-MIB download supports fleet-wide firmware and calibration tracking.

IPNetwork Monitor allows you to monitor SNMP objects defined in OPLINK-BTI-OPS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Oplink BTI optical networking module
optical transport/DWDM equipment

Monitoring Examples

An admin would poll the emuTable, using emuChassisId, emuSlotId, and emuItemId to identify a specific optical module, then check emuMfgName, emuModuleType, emuPartNum, and emuSerialNum to confirm exactly which unit is installed in that slot. Checking emuFirmwareVer across all entries would reveal whether any module is running outdated firmware relative to the rest of the fleet. Receiving an oplkemuNotifications trap tied to a specific emuChassisId/emuSlotId would alert staff to a fault on that particular optical component, prompting a check of its calibration date (emuCaliDate) and manufacturing details for warranty/support purposes.

What Can Be Monitored

optical module inventory (chassis/slot/item)
manufacturer and part/serial number
firmware version
manufacture and calibration dates
module fault trap notifications

Imported Objects

From Oplink-MIB

mngdproducts

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
deviceOPSMv2_MIB	1.3.6.1.4.1.19547.1.7			oplink device OPSM version 2 mib
STR emuAddModConfig	1.3.6.1.4.1.19547.1.7.1.1.1.22	DisplayString	read-write	AddModConfig. get: return a blank character set: Add OPSM module config, format: OPSM.PA600/OPSM.BA
OCT emuAddSNMPConfig	1.3.6.1.4.1.19547.1.7.1.1.1.52	OCTET STRING	read-write	Add snmp user. get: return a blank character set: v1 or v2c format:[Version] [Trap on/off] [IP] [Port] [Community] [Access] v3 format:[Version] [Trap on/off] [IP] [Port] [Username] [Access] [EngineID] [Level] [Auth protocol] [AuthKey] [Priv protocal] [PrivKey] Version:v1\|v2c\|v3 Trap on/off:trap\|notrap IP:xxx.xxx.xxx.xxx Port:0-65535 Community/Username:6-15 characters Access:r\|w (r:read;w:write) EngineID:0x(10-128) characters Level:AuthPriv\|AuthNoPriv\|noAuthNoPriv Auth protocol:MD5\|SHA AuthKey:8-15 characters Priv protocal:DES\|AES PrivKey:8-15 characters
HET emuBoardTemp	1.3.6.1.4.1.19547.1.7.1.1.1.17	HeTenthCentigrade	read-only	BoardTemp. Get temperature of EMU card(Unit: 0.1 degree celsius)
STR emuCaliDate	1.3.6.1.4.1.19547.1.7.1.1.1.6	DisplayString	read-only	Manufacturing date. The format is yyyy-mm-dd
I32 emuChassisId	1.3.6.1.4.1.19547.1.7.1.1.1.1001	Integer32	not-accessible	chassis index
STR emuDelModConfig	1.3.6.1.4.1.19547.1.7.1.1.1.21	DisplayString	read-write	DelModConfig. get: return a blank character set: Delete current OPSM module config. format: OPSM.PA600/OPSM.BA
OCT emuDelSNMPConfig	1.3.6.1.4.1.19547.1.7.1.1.1.51	OCTET STRING	read-write	Delete snmp user. get: return a blank character set: v1 or v2c format:[version] [IP] [Community] v3 format: [version] [username] Version:v1\|v2c\|v3 Community/Username:6-15 characters IP:xxx.xxx.xxx.xxx
emuEntry	1.3.6.1.4.1.19547.1.7.1.1.1		not-accessible	Row definition for emuTable
STR emuFirmwareUpgradeStart	1.3.6.1.4.1.19547.1.7.1.1.1.40	DisplayString	read-write	FirmwareUpgradeStart. get: return a blank character set: The name of the upgrade iamge which must be upload to the /var/ftp directory before do this operation.
STR emuFirmwareUpgradeStatus	1.3.6.1.4.1.19547.1.7.1.1.1.41	DisplayString	read-only	FirmwareUpgradeStatus. The status and percent of upgrade format: [status], [percent] status:0--none upgrade, 1--in progress, 2--upgrade successful, others-upgrade error code percent:1-100
STR emuFirmwareVer	1.3.6.1.4.1.19547.1.7.1.1.1.7	DisplayString	read-only	Software version. The format is X.Y.Z
STR emuGateway	1.3.6.1.4.1.19547.1.7.1.1.1.14	DisplayString	read-write	Gateway. The format is aaa.bbb.ccc.ddd
OCT emuGetCurrentAlarm	1.3.6.1.4.1.19547.1.7.1.1.1.60	OCTET STRING	read-only	Current alarm. The current alarm of system.
STR emuGetHisAlarm	1.3.6.1.4.1.19547.1.7.1.1.1.61	DisplayString	read-only	History alarm. Full directory of history alarm file.
STR emuGetModConfig	1.3.6.1.4.1.19547.1.7.1.1.1.20	DisplayString	read-only	GetModConfig. Get current OPSM module config. format: OPSM.PA600/OPSM.BA
OCT emuGetSNMPConfig	1.3.6.1.4.1.19547.1.7.1.1.1.50	OCTET STRING	read-only	Get all snmp users' information. format:[Version] [Trap on/off] [IP] [Port] [Community/Username] [Access/Level]... Version:v1\|v2c\|v3 Trap on/off:trap\|notrap Access:Read\|Write level:noauth\|authNoPriv MD5/SHA\|authPriv MD5/SHA DES/AES
STR emuHardwareVer	1.3.6.1.4.1.19547.1.7.1.1.1.8	DisplayString	read-only	Hardware version. The format is X.Y.Z
HET emuHighTemperatureThreshold	1.3.6.1.4.1.19547.1.7.1.1.1.18	HeTenthCentigrade	read-write	HighTempThreshold. Get/Set high temperature threshold value of EMU card(Unit: 0.1 degree celsuis), range:550~750
STR emuIpAddr	1.3.6.1.4.1.19547.1.7.1.1.1.12	DisplayString	read-write	IP address. The format is aaa.bbb.ccc.ddd
I32 emuItemId	1.3.6.1.4.1.19547.1.7.1.1.1.1003	Integer32	not-accessible	port/channel index
HET emuLowTemperatureThreshold	1.3.6.1.4.1.19547.1.7.1.1.1.19	HeTenthCentigrade	read-write	LowTempThreshold. Get/Set low temperature threshold value of EMU card(Unit: 0.1 degree celsius), range:-250~0
STR emuMacAddr	1.3.6.1.4.1.19547.1.7.1.1.1.15	DisplayString	read-only	Mac address. The format is aa:bb:cc:dd:ee:ff
STR emuMfgDate	1.3.6.1.4.1.19547.1.7.1.1.1.5	DisplayString	read-only	Manufacturing date. The format is yyyy-mm-dd.
STR emuMfgName	1.3.6.1.4.1.19547.1.7.1.1.1.1	DisplayString	read-only	Manufacturer name.
STR emuModuleType	1.3.6.1.4.1.19547.1.7.1.1.1.2	DisplayString	read-only	Module type.
STR emuNetMask	1.3.6.1.4.1.19547.1.7.1.1.1.13	DisplayString	read-write	Netmask. The format is aaa.bbb.ccc.ddd
STR emuPartNum	1.3.6.1.4.1.19547.1.7.1.1.1.3	DisplayString	read-only	Part Number. Can be any combination of alphanumerical characters.
STR emuReset	1.3.6.1.4.1.19547.1.7.1.1.1.25	DisplayString	read-write	Reset. get: return a blank character set: parameter is null.
STR emuRestoreDefault	1.3.6.1.4.1.19547.1.7.1.1.1.24	DisplayString	read-write	RestoreDefault. get: return a blank character set: parameter is null.
STR emuSaveConfig	1.3.6.1.4.1.19547.1.7.1.1.1.23	DisplayString	read-write	SaveConfig. get: return a blank character set: parameter is null.
STR emuSerialNum	1.3.6.1.4.1.19547.1.7.1.1.1.4	DisplayString	read-only	Serial number. Can be any combination of alphanumerical characters.
I32 emuSlotId	1.3.6.1.4.1.19547.1.7.1.1.1.1002	Integer32	not-accessible	slot index
STR emuSysDate	1.3.6.1.4.1.19547.1.7.1.1.1.10	DisplayString	read-write	System date. The format is YYYY-MM-DD
STR emuSysTime	1.3.6.1.4.1.19547.1.7.1.1.1.11	DisplayString	read-write	System time. The format is HH:MM:SS
emuTable	1.3.6.1.4.1.19547.1.7.1.1		not-accessible	controller card parameters
I32 emuUptime	1.3.6.1.4.1.19547.1.7.1.1.1.16	Integer32	read-only	Uptime. System uptime (Unit: s)
STR emuVendorID	1.3.6.1.4.1.19547.1.7.1.1.1.9	DisplayString	read-only	Vendor ID. The ID number of vendor.
NTF oplinkemuFanInsert	1.3.6.1.4.1.19547.1.7.1.1001.1.0.4			This trap signifies that emu fan remove alarm is clear.
NTF oplinkemuFanRemove	1.3.6.1.4.1.19547.1.7.1.1001.1.0.3			This trap signifies that emu fan card is removed.
NTF oplinkemuPowerInsert	1.3.6.1.4.1.19547.1.7.1.1001.1.0.6			This trap signifies that emu power remove alarm is clear.
NTF oplinkemuPowerRemove	1.3.6.1.4.1.19547.1.7.1.1001.1.0.5			This trap signifies that emu power card is removed.
NTF oplinkemuSubCardAdd	1.3.6.1.4.1.19547.1.7.1.1001.1.0.10			This trap signifies that emu sub-card delete alarm is clear.
NTF oplinkemuSubCardDelete	1.3.6.1.4.1.19547.1.7.1.1001.1.0.9			This trap signifies that emu sub-card is delete.
NTF oplinkemuSubCardMatch	1.3.6.1.4.1.19547.1.7.1.1001.1.0.12			This trap signifies that emu sub-card unmatch alarm is clear.
NTF oplinkemuSubCardUnmatch	1.3.6.1.4.1.19547.1.7.1.1001.1.0.11			This trap signifies that emu sub-card is unmatch with the configuration.
NTF oplinkemuTemperatureAbnormal	1.3.6.1.4.1.19547.1.7.1.1001.1.0.1			This trap signifies that emu temperature is exceess or bellow normal temperature range.
NTF oplinkemuTemperatureResume	1.3.6.1.4.1.19547.1.7.1.1001.1.0.2			This trap signifies that emu temperature abnormal alarm is clear.
NTF oplinkemuVoltageAbnormal	1.3.6.1.4.1.19547.1.7.1.1001.1.0.7			This trap signifies that emu voltage is exceess or bellow normal voltage range.
NTF oplinkemuVoltageResume	1.3.6.1.4.1.19547.1.7.1.1001.1.0.8			This trap signifies that emu voltage abnormal alarm is clear.
NTF oplinkopsmInputLosResumeRPI1	1.3.6.1.4.1.19547.1.7.1.1001.2.0.2			This trap signifies that opsm input power los alarm on CH1 primary path is clear.
NTF oplinkopsmInputLosResumeRPI2	1.3.6.1.4.1.19547.1.7.1.1001.2.0.6			This trap signifies that opsm input power los alarm on CH2 primary path is clear.
NTF oplinkopsmInputLosResumeRSI1	1.3.6.1.4.1.19547.1.7.1.1001.2.0.4			This trap signifies that opsm input power los alarm on CH1 secondary path is clear.
NTF oplinkopsmInputLosResumeRSI2	1.3.6.1.4.1.19547.1.7.1.1001.2.0.8			This trap signifies that opsm input power los alarm on CH2 secondary path is clear.
NTF oplinkopsmInputLosRPI1	1.3.6.1.4.1.19547.1.7.1.1001.2.0.1			This trap signifies that opsm input power los alarm on CH1 primary path is on.
NTF oplinkopsmInputLosRPI2	1.3.6.1.4.1.19547.1.7.1.1001.2.0.5			This trap signifies that opsm input power los alarm on CH2 primary path is on.
NTF oplinkopsmInputLosRSI1	1.3.6.1.4.1.19547.1.7.1.1001.2.0.3			This trap signifies that opsm input power los alarm on CH1 secondary path is on.
NTF oplinkopsmInputLosRSI2	1.3.6.1.4.1.19547.1.7.1.1001.2.0.7			This trap signifies that opsm input power los alarm on CH2 secondary path is on.
NTF oplinkopsmPowerDiffChannel1	1.3.6.1.4.1.19547.1.7.1.1001.2.0.9			This trap signifies that opsm input power different alarm on CH1 is on.
NTF oplinkopsmPowerDiffChannel2	1.3.6.1.4.1.19547.1.7.1.1001.2.0.11			This trap signifies that opsm input power different alarm on CH2 is on.
NTF oplinkopsmPowerDiffResumeChannel1	1.3.6.1.4.1.19547.1.7.1.1001.2.0.10			This trap signifies that opsm input power different alarm on CH1 is clear.
NTF oplinkopsmPowerDiffResumeChannel2	1.3.6.1.4.1.19547.1.7.1.1001.2.0.12			This trap signifies that opsm input power different alarm on CH2 is clear.
NTF oplinkopsmSwitchFailChannel1	1.3.6.1.4.1.19547.1.7.1.1001.2.0.13			This trap signifies that opsm switch fail alarm on CH1 is on.
NTF oplinkopsmSwitchFailChannel2	1.3.6.1.4.1.19547.1.7.1.1001.2.0.15			This trap signifies that opsm switch fail alarm on CH2 is on.
NTF oplinkopsmSwitchSuccessChannel1	1.3.6.1.4.1.19547.1.7.1.1001.2.0.14			This trap signifies that opsm switch fail alarm on CH1 is clear.
NTF oplinkopsmSwitchSuccessChannel2	1.3.6.1.4.1.19547.1.7.1.1001.2.0.16			This trap signifies that opsm switch fail alarm on CH2 is clear.
STR oplinkTrapCode	1.3.6.1.4.1.19547.1.7.1.1002	DisplayString	read-only	This object describes oplink trap. It contains information about chassis, slot, port, device type (card type) and specific error code. When get, return 0
oplkemuNotificationPrefix	1.3.6.1.4.1.19547.1.7.1.1001.1.0
oplkemuNotifications	1.3.6.1.4.1.19547.1.7.1.1001.1
oplkopsmNotificationPrefix	1.3.6.1.4.1.19547.1.7.1.1001.2.0
oplkopsmNotifications	1.3.6.1.4.1.19547.1.7.1.1001.2
oplkV6Traps	1.3.6.1.4.1.19547.1.7.1.1001
STR opsmCaliDate	1.3.6.1.4.1.19547.1.7.1.2.1.5	DisplayString	read-only	Manufacturing date. The format is yyyy-mm-dd. yyyy-1st and 2nd bytes. mm-3rd byte, dd-4th byte
I32 opsmChassisId	1.3.6.1.4.1.19547.1.7.1.2.1.1001	Integer32	not-accessible	chassis index
HET opsmDiffAlarmThreshold	1.3.6.1.4.1.19547.1.7.1.2.1.23	HeTenthdBm	read-write	Get/Set Input optical power different alarm threshold between primary and secondary, default:10,(Unit:0.1dBm),range: 0--100
I32 opsmDiffSwitchSetting	1.3.6.1.4.1.19547.1.7.1.2.1.22	Integer32	read-write	Enable or disable the function of input power different detection. 0: Disable, 1: Enable.
HET opsmDiffSwitchThreshold	1.3.6.1.4.1.19547.1.7.1.2.1.24	HeTenthdBm	read-write	Get/Set Input optical power switching threshold between primary and secondary, default:20,(Unit:0.1dBm),range: 0--100
opsmEntry	1.3.6.1.4.1.19547.1.7.1.2.1		not-accessible	Row definition for opsmTable
STR opsmFirmwareVer	1.3.6.1.4.1.19547.1.7.1.2.1.9	DisplayString	read-only	Software version. The format is X.Y.Z
STR opsmHardwareVer	1.3.6.1.4.1.19547.1.7.1.2.1.6	DisplayString	read-only	Hardware version. The format is X.Y.Z
HET opsmInherentDiffOffset	1.3.6.1.4.1.19547.1.7.1.2.1.25	HeTenthdBm	read-write	Get/Set Input Optical Power different Offset between primary and secondary,default:0,(Unit:0.1dBm),range: -300--300
HET opsmInputLosAlarmHys	1.3.6.1.4.1.19547.1.7.1.2.1.42	HeTenthdBm	read-write	The input los alarm hystersis on both path default: 10,(Unit:0.1dB),range: 10--30
HET opsmInputLosAlarmThrPathP	1.3.6.1.4.1.19547.1.7.1.2.1.40	HeTenthdBm	read-write	The input los alarm threshold on primary path default: -250,(Unit:0.1dBm),range: -350--350
HET opsmInputLosAlarmThrPathS	1.3.6.1.4.1.19547.1.7.1.2.1.41	HeTenthdBm	read-write	The input los alarm threshold on secondary path default: -250,(Unit:0.1dBm),range: -350--350
I32 opsmInputPowerPathP	1.3.6.1.4.1.19547.1.7.1.2.1.43	Integer32	read-only	The input power on primary path. (Unit:0.1dBm)
I32 opsmInputPowerPathS	1.3.6.1.4.1.19547.1.7.1.2.1.44	Integer32	read-only	The input power on secondary path. (Unit:0.1dBm)
I32 opsmItemId	1.3.6.1.4.1.19547.1.7.1.2.1.1003	Integer32	not-accessible	port/channel index
STR opsmMfgDate	1.3.6.1.4.1.19547.1.7.1.2.1.4	DisplayString	read-only	Manufacturing date. The format is yyyy-mm-dd. yyyy-1st and 2nd bytes. mm-3rd byte, dd-4th byte
STR opsmMfgName	1.3.6.1.4.1.19547.1.7.1.2.1.1	DisplayString	read-only	Manufacturer name.
STR opsmModuleType	1.3.6.1.4.1.19547.1.7.1.2.1.8	DisplayString	read-only	Module type.
STR opsmPartNum	1.3.6.1.4.1.19547.1.7.1.2.1.2	DisplayString	read-only	Part Number. Can be any combination of alphanumerical characters.
I32 opsmProtectionMode	1.3.6.1.4.1.19547.1.7.1.2.1.20	Integer32	read-write	The mode of protection switch. 0: clear, 1: force to primary, 2: force to secondary.
I32 opsmReset	1.3.6.1.4.1.19547.1.7.1.2.1.10	Integer32	read-write	0: hard reset, 1: soft reset.
I32 opsmRevertiveSetting	1.3.6.1.4.1.19547.1.7.1.2.1.21	Integer32	read-write	The action when the opticial of primary channel is resumed. 0: Non-Revertive, 1: Revertive.
STR opsmSerialNum	1.3.6.1.4.1.19547.1.7.1.2.1.3	DisplayString	read-only	Serial number. Can be any combination of alphanumerical characters.
I32 opsmSlotId	1.3.6.1.4.1.19547.1.7.1.2.1.1002	Integer32	not-accessible	slot index
I32 opsmSwitchCount	1.3.6.1.4.1.19547.1.7.1.2.1.45	Integer32	read-only	Times the switch has changed its position.
I32 opsmSwitchPosition	1.3.6.1.4.1.19547.1.7.1.2.1.28	Integer32	read-only	The position of switch. 0: Secondary 1: Primary
I32 opsmSwitchStatus	1.3.6.1.4.1.19547.1.7.1.2.1.27	Integer32	read-only	The status of protection switch. 0: IDLE, 1: WTR, 2: Auto, 3: SF_ALL, 4: N/A, 5: Forced.
opsmTable	1.3.6.1.4.1.19547.1.7.1.2		not-accessible	OPSM parameters
STR opsmVendorID	1.3.6.1.4.1.19547.1.7.1.2.1.7	DisplayString	read-only	Vendor ID. The ID number of vendor
I32 opsmWTRTime	1.3.6.1.4.1.19547.1.7.1.2.1.26	Integer32	read-write	Used in conjunction with PortID to access WTR time: default:5,(Unit:1s),range: 1--720
version2	1.3.6.1.4.1.19547.1.7.1

RFC description

OPLINK device optical supervision module with power and temperature monitoring.

Start monitoring Oplink BTI optical networking module, optical transport/DWDM equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download OPLINK-BTI-OPS-MIB

What Is OPLINK-BTI-OPS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description