All MIBs › OPTIX-SDH-PER-MIB
Organization: Huawei Technologies co.,Ltd.
Last Updated: 2006-04-14
Category: Optical Networking
Description: Collects SDH performance monitoring counters (ES, SES, BBE, UAS) for Huawei OptiX SDH transport equipment.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is OPTIX-SDH-PER-MIB?
OPTIX-SDH-PER-MIB is a Huawei-proprietary SNMP module that collects SDH (Synchronous Digital Hierarchy) performance monitoring counters for the Huawei OptiX SDH transport equipment line. It falls squarely into the performance-monitoring category of MIBs, tracking standard SDH quality-of-transmission metrics including Errored Seconds (ES), Severely Errored Seconds (SES), Background Block Errors (BBE), and Unavailable Seconds (UAS). This MIB is used to monitor the software/protocol-level performance status of the transport network's SDH paths and sections; rising ES/SES/BBE counts indicate a degrading optical or electrical signal path, while UAS indicates periods the link was actually unavailable, both key indicators of transmission-path health rather than chassis hardware sensors. It aligns with ITU-T G.826/G.828-style SDH performance-monitoring parameter definitions used industry-wide, indicating conceptual dependency on those standards even though it is implemented as a Huawei private MIB. It is typically deployed by telecom carriers operating Huawei OptiX SDH transport networks, feeding performance data into service-level and transmission-quality reporting systems. Network engineers evaluating or troubleshooting this functionality can download the OPTIX-SDH-PER-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in OPTIX-SDH-PER-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Huawei OptiX SDH optical transport equipment
Monitoring Examples
No specific table/object names were captured in the source metadata, but based on the stated performance counters, an operator would poll per-path or per-section ES, SES, BBE, and UAS counters to assess signal quality on Huawei OptiX SDH links. A spike in SES or UAS on a particular transmission path would indicate a serious degradation or outage on that SDH section, warranting immediate fault investigation. Because sample objects were not available, exact object/table names should be confirmed against the real MIB source before use in production polling.
What Can Be Monitored
- errored seconds (ES)
- severely errored seconds (SES)
- background block errors (BBE)
- unavailable seconds (UAS)
This MIB depends on
Related MIBs
Imported Objects
From OPTIX-OID-MIB
| optixCommonSdh | OBJECT-IDENTITY |
From OPTIX-SDH-TC-MIB
| SdhPerformanceEventType |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Gauge32 | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| mgmt |
From SNMPv2-TC
| DateAndTime |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| optixPerformance | 1.3.6.1.4.1.2011.2.25.3.10.20 | This module MIB describes the Optix Perfomance. | ||
| perMonitorTime | 1.3.6.1.4.1.2011.2.25.3.10.20.10 | |||
| per15mMonitorTime | 1.3.6.1.4.1.2011.2.25.3.10.20.10.10 | |||
| DAT per15mMonitorStartTime | 1.3.6.1.4.1.2011.2.25.3.10.20.10.10.10 | DateAndTime | read-write | Start date and time of 15 minutes PM period.When system enter the per15mMonitorStartTime,15 minutes PM starts.the per15mMonitorStartTime should not ealier than current date and time, specially,when it is equal to 1990-00-00 00:00:00,15 minutes PM starts immediately.reset the per15mMonitorStartTime will terminate current 15 minutes PM period.When system enter the per15mMonitorEndTime, the per15mMonitorStartTime will be reset to zero. |
| DAT per15mMonitorEndTime | 1.3.6.1.4.1.2011.2.25.3.10.20.10.10.20 | DateAndTime | read-write | End date and time of 15 minutes PM period.you need set the per15mMonitorStartTime before set the per15mMonitorEndTime,and per15mMonitorStartTime should earlier than the per15mMonitorEndTime,specially,when the per15mMonitorEndTime is equal to 1990-00-00 00:00:00,15 minutes PM ends immediately. When system enter the per15mMonitorEndTime,the per15mMonitorEndTime will be reset to zero. |
| per24hMonitorTime | 1.3.6.1.4.1.2011.2.25.3.10.20.10.20 | |||
| DAT per24hMonitorStartTime | 1.3.6.1.4.1.2011.2.25.3.10.20.10.20.10 | DateAndTime | read-write | Start date and time of one day PM period.When system enter the per24hMonitorStartTime,one day PM starts.the per24hMonitorStartTime should not ealier than current date and time, specially,when it is equal to 1990-00-00 00:00:00,one day PM starts immediately.reset the per24hMonitorStartTime will terminate current one day PM period.When system enter the per24hMonitorEndTime, the per24hMonitorStartTime will be reset to zero. |
| DAT per24hMonitorEndTime | 1.3.6.1.4.1.2011.2.25.3.10.20.10.20.20 | DateAndTime | read-write | End date and time of one day PM period.you need set the per24hMonitorStartTime before set the per24hMonitorEndTime,and per24hMonitorStartTime should earlier than the per24hMonitorEndTime,specially,when the per24hMonitorEndTime is equal to 1990-00-00 00:00:00,one day PM ends immediately. When system enter the per24hMonitorEndTime,the per24hMonitorEndTime will be reset to zero. |
| perMonitorData | 1.3.6.1.4.1.2011.2.25.3.10.20.20 | |||
| per15mMonitoring | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10 | |||
| per15mCurrentDataTable | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.10 | not-accessible | 15 minutes PM period current data table | |
| per15mCurrentDataEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.10.1 | not-accessible | 15 minutes PM period current data entry | |
| G32 per15mCurrentDataBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.10.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per15mCurrentDataOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.10.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per15mCurrentDataPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.10.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per15mCurrentDataEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.10.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| DAT per15mCurrentDataStartTime | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.10.1.5 | DateAndTime | read-only | start date and time: start date and time of current 15 minutes PM period. |
| G32 per15mCurrentDataValue | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.10.1.6 | Gauge32 | read-only | Current data value: value of current 15 minutes PM period register.the units of value vary as the PM event,fo example,the unit of RSUAS is 'second',while the unit of RSBBE is 'count'. |
| INT per15mCurrentDataReset | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.10.1.7 | INTEGER | read-write | Current data reset: reset value of current 15 minutes PM period register to zero. |
| per15mHistoryDataTable | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.20 | not-accessible | 15 minutes PM period historic data table | |
| per15mHistoryDataEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.20.1 | not-accessible | 15 minutes PM period historic data entry | |
| G32 per15mHistoryDataBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.20.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per15mHistoryDataOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.20.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per15mHistoryDataPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.20.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per15mHistoryDataEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.20.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| DAT per15mHistoryDataStartTime | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.20.1.5 | DateAndTime | read-only | start date and time: start date and time of special 15 minutes PM period. |
| G32 per15mHistoryDataValue | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.20.1.6 | Gauge32 | read-only | Historic data value: value of special 15 minutes PM period register.the units of value vary as the PM event,fo example,the unit of RSUAS is 'second',while the unit of RSBBE is 'count'. |
| INT per15mHistoryDataReset | 1.3.6.1.4.1.2011.2.25.3.10.20.20.10.20.1.7 | INTEGER | read-write | Historic data reset: reset value of special 15 minutes PM period register to zero. |
| per24hMonitoring | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20 | |||
| per24hCurrentDataTable | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.10 | not-accessible | one day PM period current data table | |
| per24hCurrentDataEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.10.1 | not-accessible | one day PM period current data entry | |
| G32 per24hCurrentDataBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.10.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per24hCurrentDataOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.10.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per24hCurrentDataPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.10.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per24hCurrentDataEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.10.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| DAT per24hCurrentDataStartTime | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.10.1.5 | DateAndTime | read-only | start date and time: start date and time of current one day PM period. |
| G32 per24hCurrentDataValue | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.10.1.6 | Gauge32 | read-only | Current data value: value of current one day PM period register.the units of value vary as the PM event,fo example,the unit of RSUAS is 'second',while the unit of RSBBE is 'count'. |
| INT per24hCurrentDataReset | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.10.1.7 | INTEGER | read-write | Current data reset: reset value of current one day PM period register to zero. |
| per24hHistoryDataTable | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.20 | not-accessible | one day PM period historic data table | |
| per24hHistoryDataEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.20.1 | not-accessible | one day PM period historic data entry | |
| G32 per24hHistoryDataBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.20.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per24hHistoryDataOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.20.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per24hHistoryDataPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.20.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per24hHistoryDataEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.20.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| DAT per24hHistoryDataStartTime | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.20.1.5 | DateAndTime | read-only | start date and time: start date and time of special one day PM period. |
| G32 per24hHistoryDataValue | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.20.1.6 | Gauge32 | read-only | Historic data value: value of special one day PM period register.the units of value vary as the PM event,fo example,the unit of RSUAS is 'second',while the unit of RSBBE is 'count'. |
| INT per24hHistoryDataReset | 1.3.6.1.4.1.2011.2.25.3.10.20.20.20.20.1.7 | INTEGER | read-write | Historic data reset: reset value of special one day PM period register to zero. |
| perThreshold | 1.3.6.1.4.1.2011.2.25.3.10.20.30 | |||
| per15mThreshold | 1.3.6.1.4.1.2011.2.25.3.10.20.30.10 | |||
| per15mThresholdTable | 1.3.6.1.4.1.2011.2.25.3.10.20.30.10.10 | not-accessible | 15 minutes PM period threshold table | |
| per15mThresholdEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.30.10.10.1 | not-accessible | 15 minutes PM period threshold entry | |
| G32 per15mThresholdBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.30.10.10.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per15mThresholdOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.30.10.10.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per15mThresholdPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.30.10.10.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per15mThresholdEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.30.10.10.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| G32 per15mThresholdHighValue | 1.3.6.1.4.1.2011.2.25.3.10.20.30.10.10.1.5 | Gauge32 | read-write | High threshold value: some parameters have two thresholds,such as RSBBE, while others have single threshold,such as RSSES. |
| G32 per15mThresholdLowValue | 1.3.6.1.4.1.2011.2.25.3.10.20.30.10.10.1.6 | Gauge32 | read-write | Low threshold value: specially,some parameters have single threshold, so their Low threshold should always be zero. |
| INT per15mThresholdReset | 1.3.6.1.4.1.2011.2.25.3.10.20.30.10.10.1.7 | INTEGER | read-write | Threshold reset: reset both high threshold and low threshold(if has). |
| per24hThreshold | 1.3.6.1.4.1.2011.2.25.3.10.20.30.20 | |||
| per24hThresholdTable | 1.3.6.1.4.1.2011.2.25.3.10.20.30.20.10 | not-accessible | one day PM period threshold table | |
| per24hThresholdEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.30.20.10.1 | not-accessible | one day PM period threshold entry | |
| G32 per24hThresholdBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.30.20.10.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per24hThresholdOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.30.20.10.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per24hThresholdPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.30.20.10.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per24hThresholdEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.30.20.10.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| G32 per24hThresholdValue | 1.3.6.1.4.1.2011.2.25.3.10.20.30.20.10.1.5 | Gauge32 | read-write | Threshold value: all parameters have only one threshold value for one day PM period. |
| INT per24hThresholdReset | 1.3.6.1.4.1.2011.2.25.3.10.20.30.20.10.1.6 | INTEGER | read-write | Threshold reset: reset threshold. |
| perStatus | 1.3.6.1.4.1.2011.2.25.3.10.20.40 | |||
| perStatusControl | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10 | |||
| per15mStatusControl | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10 | |||
| per15mMonitorStatusTable | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.10 | not-accessible | 15 minutes PM period monitor status table. | |
| per15mMonitorStatusEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.10.1 | not-accessible | 15 minutes PM period monitor status entry. | |
| G32 per15mMonitorStatusBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.10.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per15mMonitorStatusOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.10.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per15mMonitorStatusPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.10.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per15mMonitorStatusEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.10.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| INT per15mMonitorStatus | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.10.1.5 | INTEGER | read-write | Monitor status: when monitor status is disabled,current data register is reset to zero and will not increase any more until monitor status be enabled. The default monitor status is enable. |
| per15mPauseStatusTable | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.20 | not-accessible | 15 minutes PM period pause status table. | |
| per15mPauseStatusEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.20.1 | not-accessible | 15 minutes PM period pause status entry. | |
| G32 per15mPauseStatusBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.20.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per15mPauseStatusOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.20.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per15mPauseStatusPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.20.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per15mPauseStatusEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.20.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| INT per15mPauseStatus | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.20.1.5 | INTEGER | read-write | Pause status: when pause status is disabled,current data register will not increase (but will reset to zero)any more until pause status be enabled.The default monitor status is disable. |
| per15mThresholdStatusTable | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.30 | not-accessible | 15 minutes PM period threshold status table | |
| per15mThresholdStatusEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.30.1 | not-accessible | 15 minutes PM period threshold status entry | |
| G32 per15mThresholdStatusBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.30.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per15mThresholdStatusOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.30.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per15mThresholdStatusPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.30.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per15mThresholdStatusEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.30.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| INT per15mThresholdStatus | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.30.1.5 | INTEGER | read-write | Threshold status:when threshold status is disabled,no threshold crossing alert will be reported even though threshold is crossed.The default threshold status is enable. |
| per15mAutoReportStatusTable | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.40 | not-accessible | 15 minutes PM period automatic report(REP) status table | |
| per15mAutoReportStatusEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.40.1 | not-accessible | 15 minutes PM period automatic report(REP) status entry | |
| G32 per15mAutoReportStatusBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.40.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per15mAutoReportStatusOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.40.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per15mAutoReportStatusPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.40.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per15mAutoReportStatusEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.40.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| INT per15mAutoReportStatus | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.10.40.1.5 | INTEGER | read-write | Automatic report status: if automatic report status is enabled, when PM period expired, NE will report none-zero current data register value to user.The default automatic report status is enable . |
| per24hStatusControl | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20 | |||
| per24hMonitorStatusTable | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.10 | not-accessible | one day PM period monitor status table. | |
| per24hMonitorStatusEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.10.1 | not-accessible | one day PM period monitor status entry. | |
| G32 per24hMonitorStatusBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.10.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per24hMonitorStatusOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.10.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per24hMonitorStatusPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.10.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per24hMonitorStatusEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.10.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| INT per24hMonitorStatus | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.10.1.5 | INTEGER | read-write | Monitor status: when monitor status is disabled,current data register is reset to zero and will not increase any more until monitor status be enabled.The default monitor status is enable. |
| per24hPauseStatusTable | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.20 | not-accessible | one day PM period pause status table. | |
| per24hPauseStatusEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.20.1 | not-accessible | one day PM period pause status entry. | |
| G32 per24hPauseStatusBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.20.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per24hPauseStatusOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.20.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per24hPauseStatusPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.20.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per24hPauseStatusEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.20.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| INT per24hPauseStatus | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.20.1.5 | INTEGER | read-write | Pause status: when pause status is disabled,current data register will not increase (but will reset to zero)any more until pause status be enabled.The default monitor status is disable. |
| per24hThresholdStatusTable | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.30 | not-accessible | one day PM period threshold status table. | |
| per24hThresholdStatusEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.30.1 | not-accessible | one day PM period threshold status entry. | |
| G32 per24hThresholdStatusBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.30.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per24hThresholdStatusOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.30.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per24hThresholdStatusPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.30.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per24hThresholdStatusEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.30.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| INT per24hThresholdStatus | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.30.1.5 | INTEGER | read-write | Threshold status:when threshold status is disabled,no threshold crossing alert will be reported even though threshold is crossed.The default threshold status is enable. |
| per24hAutoReportStatusTable | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.40 | not-accessible | one day PM period automatic report(REP) status table. | |
| per24hAutoReportStatusEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.40.1 | not-accessible | one day PM period automatic report(REP) status entry. | |
| G32 per24hAutoReportStatusBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.40.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per24hAutoReportStatusOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.40.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per24hAutoReportStatusPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.40.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per24hAutoReportStatusEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.40.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| INT per24hAutoReportStatus | 1.3.6.1.4.1.2011.2.25.3.10.20.40.10.20.40.1.5 | INTEGER | read-write | Automatic report status: if automatic report status is enabled, when PM period expired, NE will report none-zero current data register value to user.The default automatic report status is enable . |
| perThresholdCrossStatus | 1.3.6.1.4.1.2011.2.25.3.10.20.40.20 | |||
| per15mThresholdCrossStatusTable | 1.3.6.1.4.1.2011.2.25.3.10.20.40.20.10 | not-accessible | 15 minutes PM period threshold crossing status table. | |
| per15mThresholdCrossStatusEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.40.20.10.1 | not-accessible | 15 minutes PM period threshold crossing status entry. | |
| G32 per15mThresholdCrossStatusBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.40.20.10.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per15mThresholdCrossStatusOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.40.20.10.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per15mThresholdCrossStatusPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.40.20.10.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per15mThresholdCrossStatusEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.40.20.10.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| INT per15mThresholdCrossStatus | 1.3.6.1.4.1.2011.2.25.3.10.20.40.20.10.1.5 | INTEGER | read-only | Threshold crossing status:normal-threshold was not crossed,crossed -threshold was crossed. |
| per24hThresholdCrossStatusTable | 1.3.6.1.4.1.2011.2.25.3.10.20.40.20.20 | not-accessible | one day PM period threshold crossing status table. | |
| per24hThresholdCrossStatusEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.40.20.20.1 | not-accessible | one day PM period threshold crossing status entry. | |
| G32 per24hThresholdCrossStatusBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.40.20.20.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 per24hThresholdCrossStatusOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.40.20.20.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 per24hThresholdCrossStatusPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.40.20.20.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH per24hThresholdCrossStatusEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.40.20.20.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| INT per24hThresholdCrossStatus | 1.3.6.1.4.1.2011.2.25.3.10.20.40.20.20.1.5 | INTEGER | read-only | Threshold crossing status:normal-threshold was not crossed,crossed -threshold was crossed. |
| perEvents | 1.3.6.1.4.1.2011.2.25.3.10.20.50 | |||
| perUATEvent | 1.3.6.1.4.1.2011.2.25.3.10.20.50.10 | |||
| perUATEventTable | 1.3.6.1.4.1.2011.2.25.3.10.20.50.10.10 | not-accessible | UAT event table. | |
| perUATEventEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.50.10.10.1 | not-accessible | UAT event entry. | |
| G32 perUATBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.50.10.10.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 perUATOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.50.10.10.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 perUATPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.50.10.10.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH perUATEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.50.10.10.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| DAT perUATStartTime | 1.3.6.1.4.1.2011.2.25.3.10.20.50.10.10.1.5 | DateAndTime | read-only | the date and time when enter UAT. |
| DAT perUATEndTime | 1.3.6.1.4.1.2011.2.25.3.10.20.50.10.10.1.6 | DateAndTime | read-only | the date and time when exit UAT. |
| perCSESEvent | 1.3.6.1.4.1.2011.2.25.3.10.20.50.20 | |||
| perCSESEventTable | 1.3.6.1.4.1.2011.2.25.3.10.20.50.20.10 | not-accessible | CSES event table. | |
| perCSESEventEntry | 1.3.6.1.4.1.2011.2.25.3.10.20.50.20.10.1 | not-accessible | CSES event entry. | |
| G32 perCSESBoardNo | 1.3.6.1.4.1.2011.2.25.3.10.20.50.20.10.1.1 | Gauge32 | read-only | Card No.:between 1 and 20 |
| G32 perCSESOpticalPort | 1.3.6.1.4.1.2011.2.25.3.10.20.50.20.10.1.2 | Gauge32 | read-only | Optical port No.:values depend on type of card |
| G32 perCSESPathNumber | 1.3.6.1.4.1.2011.2.25.3.10.20.50.20.10.1.3 | Gauge32 | read-only | Path No.:values depend on type of card |
| SDH perCSESEventID | 1.3.6.1.4.1.2011.2.25.3.10.20.50.20.10.1.4 | SdhPerformanceEventType | read-only | Event ID:values depend on type of card |
| DAT perCSESStartTime | 1.3.6.1.4.1.2011.2.25.3.10.20.50.20.10.1.5 | DateAndTime | read-only | the date and time when enter CSES. |
| G32 perCSESKeepTime | 1.3.6.1.4.1.2011.2.25.3.10.20.50.20.10.1.6 | Gauge32 | read-only | the count of CSES continues. |
| optixCommonSdhConformance | 1.3.6.1.4.1.2011.2.25.3.10.20.90 | |||
| optixCommonSdhGroups | 1.3.6.1.4.1.2011.2.25.3.10.20.90.1 | |||
| currentObjectGroup | 1.3.6.1.4.1.2011.2.25.3.10.20.90.1.1 | Enter the description of the created OBJECT-GROUP. | ||
| optixCommonSdhCompliances | 1.3.6.1.4.1.2011.2.25.3.10.20.90.2 | |||
| optixCommonSdhbasicCompliance | 1.3.6.1.4.1.2011.2.25.3.10.20.90.2.1 | Enter the description of the created MODULE-COMPLIANCE. |
RFC description
Huawei OPTIX performance monitoring MIB for SDH networks, tracking 15-minute and daily performance events and thresholds.
Start monitoring Huawei OptiX SDH optical transport equipment (ES/SES/BBE/UAS performance counters) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.