Nortel-Magellan-Passport-AtmIispMIB

All MIBs › Nortel-Magellan-Passport-AtmIispMIB

Category: ATM

Description: Manages Nortel Magellan Passport ATM IISP inter-switch signaling and routing configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Nortel-Magellan-Passport-AtmIispMIB?

This MIB manages Interim Inter-Switch Signaling Protocol (IISP) configuration for ATM inter-switch signaling and routing on Nortel's Magellan Passport carrier switching platform. It belongs to the Nortel legacy ATM WAN switching technology area. It exposes provisioning and row-status tables for IISP components on ATM interfaces, including protocol version, side (network/user), and soft PVC retry timing parameters, following the Passport platform's characteristic component/row-status provisioning model. Its role is chiefly in configuring and verifying signaling interconnection status between ATM switches, confirming an IISP link's provisioned side and version match its peer and that soft PVC retries are not repeatedly failing, rather than exposing environmental hardware sensors. It builds on the general ATM UNI/NNI signaling model that IISP itself extends, and is structured according to Nortel Passport's common component-naming/row-status conventions shared across sibling Passport MIBs. It is typically deployed on Nortel Magellan Passport ATM switches at carrier network interconnection points. Engineers can download the Nortel-Magellan-Passport-AtmIispMIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Nortel-Magellan-Passport-AtmIispMIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Nortel Magellan Passport ATM switch

Monitoring Examples

An operator would query atmIfIispProvTable/atmIfIispProvEntry for a given interface to check atmIfIispVersion and atmIfIispSide, confirming both ends of an inter-switch link agree on IISP version and network/user role, and would check atmIfIispRowStatusTable/atmIfIispRowStatus to verify the IISP component is provisioned active. Monitoring atmIfIispSoftPvcRetryPeriod alongside repeated retry attempts would reveal a soft PVC failing to establish across the IISP link, indicating a signaling mismatch or downstream connectivity problem. This table-and-row-status structure is typical of Passport component MIBs where status is inferred from row state rather than dedicated counters.

What Can Be Monitored

IISP link provisioning status
IISP protocol version
IISP side (network/user) configuration
soft PVC retry period
IISP component row status

Imported Objects

From Nortel-Magellan-Passport-AtmCoreMIB

atmIf	OBJECT-IDENTITY
atmIfIndex	OBJECT-TYPE
atmIfVpt	OBJECT-IDENTITY
atmIfVptIndex	OBJECT-TYPE

From Nortel-Magellan-Passport-StandardTextualConventionsMIB

Counter32
DisplayString
Gauge32
Integer32
RowStatus
StorageType
Unsigned32

From Nortel-Magellan-Passport-TextualConventionsMIB

AsciiStringIndex
Hex
NonReplicated

From Nortel-Magellan-Passport-UsefulDefinitionsMIB

passportMIBs

OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

OIDs

OID symbolic	OID numeric	Type	Access	Description
atmIfIisp	1.3.6.1.4.1.562.2.4.1.114.7
atmIfIispRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.7.1		not-accessible	This entry controls the addition and deletion of atmIfIisp components.
atmIfIispRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.7.1.1		not-accessible	A single entry in the table represents a single atmIfIisp component.
ROW atmIfIispRowStatus	1.3.6.1.4.1.562.2.4.1.114.7.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfIisp components. These components can be added and deleted.
STR atmIfIispComponentName	1.3.6.1.4.1.562.2.4.1.114.7.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfIispStorageType	1.3.6.1.4.1.562.2.4.1.114.7.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfIisp tables.
NON atmIfIispIndex	1.3.6.1.4.1.562.2.4.1.114.7.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfIisp tables.
atmIfIispSig	1.3.6.1.4.1.562.2.4.1.114.7.3
atmIfIispSigRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.7.3.1		not-accessible	This entry controls the addition and deletion of atmIfIispSig components.
atmIfIispSigRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.7.3.1.1		not-accessible	A single entry in the table represents a single atmIfIispSig component.
ROW atmIfIispSigRowStatus	1.3.6.1.4.1.562.2.4.1.114.7.3.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of atmIfIispSig components. These components cannot be added nor deleted.
STR atmIfIispSigComponentName	1.3.6.1.4.1.562.2.4.1.114.7.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfIispSigStorageType	1.3.6.1.4.1.562.2.4.1.114.7.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfIispSig tables.
NON atmIfIispSigIndex	1.3.6.1.4.1.562.2.4.1.114.7.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfIispSig tables.
atmIfIispSigVcd	1.3.6.1.4.1.562.2.4.1.114.7.3.2
atmIfIispSigVcdRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.7.3.2.1		not-accessible	This entry controls the addition and deletion of atmIfIispSigVcd components.
atmIfIispSigVcdRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.7.3.2.1.1		not-accessible	A single entry in the table represents a single atmIfIispSigVcd component.
ROW atmIfIispSigVcdRowStatus	1.3.6.1.4.1.562.2.4.1.114.7.3.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfIispSigVcd components. These components can be added and deleted.
STR atmIfIispSigVcdComponentName	1.3.6.1.4.1.562.2.4.1.114.7.3.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfIispSigVcdStorageType	1.3.6.1.4.1.562.2.4.1.114.7.3.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfIispSigVcd tables.
NON atmIfIispSigVcdIndex	1.3.6.1.4.1.562.2.4.1.114.7.3.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfIispSigVcd tables.
atmIfIispSigVcdProvTable	1.3.6.1.4.1.562.2.4.1.114.7.3.2.10		not-accessible	This group contains the provisionable traffic attributes for a control channel.
atmIfIispSigVcdProvEntry	1.3.6.1.4.1.562.2.4.1.114.7.3.2.10.1		not-accessible	An entry in the atmIfIispSigVcdProvTable.
INT atmIfIispSigVcdTrafficDescType	1.3.6.1.4.1.562.2.4.1.114.7.3.2.10.1.1	INTEGER	read-write	This attribute specifies the type of traffic management which is applied to both the transmit and receive direction of this connection as defined in the ATM Forum. The trafficDescType determines the number and meaning of the parameters in the trafficDescParm attribute.
INT atmIfIispSigVcdAtmServiceCategory	1.3.6.1.4.1.562.2.4.1.114.7.3.2.10.1.3	INTEGER	read-write	This attribute specifies the ATM service category for both directions of the connection. The constantBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by CellTransfer Delay are assumed to be of significantly reduce value to the application. The rtVariableBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by CTD are assumed to be of significantly reduced value to the application. Real time VBR service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. Non-real time VBR service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications; that is, those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection.
INT atmIfIispSigVcdQosClass	1.3.6.1.4.1.562.2.4.1.114.7.3.2.10.1.21	INTEGER	read-write	This attribute specifies the quality of service for both the forward and backward direction for this connection. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters.
INT atmIfIispSigVcdTrafficShaping	1.3.6.1.4.1.562.2.4.1.114.7.3.2.10.1.50	INTEGER	read-write	This attribute specifies whether this connection uses traffic shaping when transmitting traffic to the ATM interface. When sameAsCa is selected, traffic shaping for this connection is based on the trafficShaping attribute of the connection's service category component under the AtmIf CA. If the service category has traffic shaping enabled, then traffic shaping is enabled for the connection. Note that enabling traffic shaping may have no effect under certain cases. These cases are listed in the description of the trafficShaping operational attribute, which is under the Vcc Tm and Vpc Tm components. When disabled is selected, traffic shaping for this connection is disabled.
INT atmIfIispSigVcdUnshapedTransmitQueueing	1.3.6.1.4.1.562.2.4.1.114.7.3.2.10.1.60	INTEGER	read-write	This attribute only applies when this connection is unshaped. This attribute specifies the transmit queueing method for this connection if it is unshaped. Refer to the unshapedTransmitQueueing attribute under the AtmIf CA service category subcomponent for more details on the meaning of this attribute. When this attribute is set to sameAsCa, the transmit queueing method for the connection is based on the unshapedTransmitQueueing attribute of the connection's service category component under the ConnectionAdministrator. When this attribute is set to common, transmit traffic on this unshaped connection is destined for the common queue. The value sameAsInterface is for migration from previous software releases, but should no longer be used
INT atmIfIispSigVcdUsageParameterControl	1.3.6.1.4.1.562.2.4.1.114.7.3.2.10.1.70	INTEGER	read-write	This attribute specifies whether this connection enforces usage parameter control when receiving traffic from the ATM interface. When sameAsCa is selected, UPC for the connection is based on the usageParameterControl attribute of the connection's service category component under the ConnectionAdministrator. If the service category has UPC enabled, then UPC is enabled for the connection. Note that enabling UPC may have no effect under certain cases. These cases are listed in the description of the usageParameterControl operational attribute, which is under the Vcc Tm or Vpc Tm component. When disabled is selected, UPC for this connection is disabled. The value sameAsInterface is for migration from previous software releases, but should no longer be used
atmIfIispSigVcdTdpTable	1.3.6.1.4.1.562.2.4.1.114.7.3.2.387		not-accessible	This attribute is a vector of five traffic parameters whose meanings are defined by the trafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When trafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When trafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For trafficDescType 3 the traffic is shaped at the next rate less than the PCR. For trafficDescType 6, 7, and 8, the traffic is shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic is shaped at the next rate above the PCR.
atmIfIispSigVcdTdpEntry	1.3.6.1.4.1.562.2.4.1.114.7.3.2.387.1		not-accessible	An entry in the atmIfIispSigVcdTdpTable.
I32 atmIfIispSigVcdTdpIndex	1.3.6.1.4.1.562.2.4.1.114.7.3.2.387.1.1	Integer32	not-accessible	This variable represents the atmIfIispSigVcdTdpTable specific index for the atmIfIispSigVcdTdpTable.
U32 atmIfIispSigVcdTdpValue	1.3.6.1.4.1.562.2.4.1.114.7.3.2.387.1.2	Unsigned32	read-write	This variable represents an individual value for the atmIfIispSigVcdTdpTable.
atmIfIispSigProvTable	1.3.6.1.4.1.562.2.4.1.114.7.3.10		not-accessible	This attribute group contains the provisionable attributes for the Signalling component.
atmIfIispSigProvEntry	1.3.6.1.4.1.562.2.4.1.114.7.3.10.1		not-accessible	An entry in the atmIfIispSigProvTable.
U32 atmIfIispSigVci	1.3.6.1.4.1.562.2.4.1.114.7.3.10.1.1	Unsigned32	read-write	This attribute specifies the signalling channel number.
INT atmIfIispSigAddressConversion	1.3.6.1.4.1.562.2.4.1.114.7.3.10.1.2	INTEGER	read-write	This attribute specifies the address conversion on the outgoing signalling PDUs. The options are none, nativeE164, or nsap. The none option is the default and if this option is chosen then nothing is done to the address information element (IE) in the outgoing signalling message. If nativeE164 option is chosen, then only NSAP encapsulated E.164 addresses with zeros in the ESI are converted to native E.164 format in the outgoing signalling message. If the NSAP address is not encapsulated E.164 or the ESI field is not zeros and the nativeE164 option is chosen, then the call is cleared. If the nsap option is chosen, then native E.164 addresses are converted to NSAP E.164 with zeros in the ESI field; otherwise the address is in NSAP format and is not changed.
atmIfIispSigStateTable	1.3.6.1.4.1.562.2.4.1.114.7.3.11		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
atmIfIispSigStateEntry	1.3.6.1.4.1.562.2.4.1.114.7.3.11.1		not-accessible	An entry in the atmIfIispSigStateTable.
INT atmIfIispSigAdminState	1.3.6.1.4.1.562.2.4.1.114.7.3.11.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT atmIfIispSigOperationalState	1.3.6.1.4.1.562.2.4.1.114.7.3.11.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT atmIfIispSigUsageState	1.3.6.1.4.1.562.2.4.1.114.7.3.11.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
atmIfIispSigOperTable	1.3.6.1.4.1.562.2.4.1.114.7.3.12		not-accessible	This attribute contains the operational attributes for the AtmSignalling component.
atmIfIispSigOperEntry	1.3.6.1.4.1.562.2.4.1.114.7.3.12.1		not-accessible	An entry in the atmIfIispSigOperTable.
U32 atmIfIispSigLastTxCauseCode	1.3.6.1.4.1.562.2.4.1.114.7.3.12.1.1	Unsigned32	read-only	This attribute indicates the cause code in the last transmitted signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX atmIfIispSigLastTxDiagCode	1.3.6.1.4.1.562.2.4.1.114.7.3.12.1.2	Hex	read-only	This attribute contains the diagnostic code in the last transmitted signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
U32 atmIfIispSigLastRxCauseCode	1.3.6.1.4.1.562.2.4.1.114.7.3.12.1.3	Unsigned32	read-only	This attribute contains the cause code in the last received signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX atmIfIispSigLastRxDiagCode	1.3.6.1.4.1.562.2.4.1.114.7.3.12.1.4	Hex	read-only	This attribute contains the diagnostic code in the last received signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
atmIfIispSigStatsTable	1.3.6.1.4.1.562.2.4.1.114.7.3.13		not-accessible	This attribute group contains the statistics associated with the AtmSignalling component.
atmIfIispSigStatsEntry	1.3.6.1.4.1.562.2.4.1.114.7.3.13.1		not-accessible	An entry in the atmIfIispSigStatsTable.
C32 atmIfIispSigCurrentConnections	1.3.6.1.4.1.562.2.4.1.114.7.3.13.1.1	Counter32	read-only	This attribute indicates the total number of currently active connections.
G32 atmIfIispSigPeakConnections	1.3.6.1.4.1.562.2.4.1.114.7.3.13.1.2	Gauge32	read-only	This attribute indicates the high water mark of active point-to- point and point-to-multipoint connections.
C32 atmIfIispSigSuccessfulConnections	1.3.6.1.4.1.562.2.4.1.114.7.3.13.1.3	Counter32	read-only	This attribute counts the total number of switched point-to- point and point-to-multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfIispSigFailedConnections	1.3.6.1.4.1.562.2.4.1.114.7.3.13.1.4	Counter32	read-only	This attribute counts the total number of switched connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfIispSigTxPdus	1.3.6.1.4.1.562.2.4.1.114.7.3.13.1.5	Counter32	read-only	This attribute counts the number of transmitted signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfIispSigRxPdus	1.3.6.1.4.1.562.2.4.1.114.7.3.13.1.6	Counter32	read-only	This attribute counts the number of received signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
G32 atmIfIispSigCurrentPmpConnections	1.3.6.1.4.1.562.2.4.1.114.7.3.13.1.7	Gauge32	read-only	This attribute indicates the number of currently active point-to- multipoint connections.
G32 atmIfIispSigPeakPmpConnections	1.3.6.1.4.1.562.2.4.1.114.7.3.13.1.8	Gauge32	read-only	This attribute indicates the high water mark of active point-to- multipoint connections.
C32 atmIfIispSigSuccessfulPmpConnections	1.3.6.1.4.1.562.2.4.1.114.7.3.13.1.9	Counter32	read-only	This attribute counts the total number of switched point-to- multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfIispSigFailedPmpConnections	1.3.6.1.4.1.562.2.4.1.114.7.3.13.1.10	Counter32	read-only	This attribute counts the number of switched point-to- multipoint connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
G32 atmIfIispSigNewCurrentConnections	1.3.6.1.4.1.562.2.4.1.114.7.3.13.1.11	Gauge32	read-only	This attribute indicates the total number of currently active point-to- point and point-to-multipoint connections.
atmIfIispAddr	1.3.6.1.4.1.562.2.4.1.114.7.4
atmIfIispAddrRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.7.4.1		not-accessible	This entry controls the addition and deletion of atmIfIispAddr components.
atmIfIispAddrRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.7.4.1.1		not-accessible	A single entry in the table represents a single atmIfIispAddr component.
ROW atmIfIispAddrRowStatus	1.3.6.1.4.1.562.2.4.1.114.7.4.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfIispAddr components. These components can be added and deleted.
STR atmIfIispAddrComponentName	1.3.6.1.4.1.562.2.4.1.114.7.4.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfIispAddrStorageType	1.3.6.1.4.1.562.2.4.1.114.7.4.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfIispAddr tables.
STR atmIfIispAddrAddressIndex	1.3.6.1.4.1.562.2.4.1.114.7.4.1.1.10	AsciiStringIndex	not-accessible	This variable represents an index for the atmIfIispAddr tables.
INT atmIfIispAddrAddressTypeIndex	1.3.6.1.4.1.562.2.4.1.114.7.4.1.1.11	INTEGER	not-accessible	This variable represents an index for the atmIfIispAddr tables.
atmIfIispAddrTermSP	1.3.6.1.4.1.562.2.4.1.114.7.4.2
atmIfIispAddrTermSPRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.7.4.2.1		not-accessible	This entry controls the addition and deletion of atmIfIispAddrTermSP components.
atmIfIispAddrTermSPRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.7.4.2.1.1		not-accessible	A single entry in the table represents a single atmIfIispAddrTermSP component.
ROW atmIfIispAddrTermSPRowStatus	1.3.6.1.4.1.562.2.4.1.114.7.4.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfIispAddrTermSP components. These components can be added and deleted.
STR atmIfIispAddrTermSPComponentName	1.3.6.1.4.1.562.2.4.1.114.7.4.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfIispAddrTermSPStorageType	1.3.6.1.4.1.562.2.4.1.114.7.4.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfIispAddrTermSP tables.
NON atmIfIispAddrTermSPIndex	1.3.6.1.4.1.562.2.4.1.114.7.4.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfIispAddrTermSP tables.
atmIfIispAddrPnniInfo	1.3.6.1.4.1.562.2.4.1.114.7.4.3
atmIfIispAddrPnniInfoRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.7.4.3.1		not-accessible	This entry controls the addition and deletion of atmIfIispAddrPnniInfo components.
atmIfIispAddrPnniInfoRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.7.4.3.1.1		not-accessible	A single entry in the table represents a single atmIfIispAddrPnniInfo component.
ROW atmIfIispAddrPnniInfoRowStatus	1.3.6.1.4.1.562.2.4.1.114.7.4.3.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfIispAddrPnniInfo components. These components can be added and deleted.
STR atmIfIispAddrPnniInfoComponentName	1.3.6.1.4.1.562.2.4.1.114.7.4.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfIispAddrPnniInfoStorageType	1.3.6.1.4.1.562.2.4.1.114.7.4.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfIispAddrPnniInfo tables.
NON atmIfIispAddrPnniInfoIndex	1.3.6.1.4.1.562.2.4.1.114.7.4.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfIispAddrPnniInfo tables.
atmIfIispAddrPnniInfoProvTable	1.3.6.1.4.1.562.2.4.1.114.7.4.3.10		not-accessible	This attribute group contains the provisioned attributes relating to PNNI for a PnniInfo component.
atmIfIispAddrPnniInfoProvEntry	1.3.6.1.4.1.562.2.4.1.114.7.4.3.10.1		not-accessible	An entry in the atmIfIispAddrPnniInfoProvTable.
INT atmIfIispAddrPnniInfoScope	1.3.6.1.4.1.562.2.4.1.114.7.4.3.10.1.1	INTEGER	read-write	This attribute specifies the scope of the ATM address, which is the highest level up to which this address will be advertised in the PNNI hierarchy. The scope must be set to a value numerically less than or equal to the level of the lowest level peer group containing this node. Setting the scope to 0 will cause the address to be advertised globally within this PNNI routing domain.
INT atmIfIispAddrPnniInfoReachability	1.3.6.1.4.1.562.2.4.1.114.7.4.3.10.1.2	INTEGER	read-write	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
atmIfIispAddrOperTable	1.3.6.1.4.1.562.2.4.1.114.7.4.10		not-accessible	This attribute group contains the operational attributes for the Address component.
atmIfIispAddrOperEntry	1.3.6.1.4.1.562.2.4.1.114.7.4.10.1		not-accessible	An entry in the atmIfIispAddrOperTable.
INT atmIfIispAddrScope	1.3.6.1.4.1.562.2.4.1.114.7.4.10.1.1	INTEGER	read-only	This attribute indicates the scope of the ATM address, which is the highest level to which this address will be advertised in the PNNI hierarchy. If no PnniInfo subcomponent has been provisioned, then the scope will default to the level of this node in the PNNI hierarchy. If this node does not participate in a PNNI hierarchy, then this attribute will have the value of -1.
INT atmIfIispAddrReachability	1.3.6.1.4.1.562.2.4.1.114.7.4.10.1.2	INTEGER	read-only	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
atmIfIispProvTable	1.3.6.1.4.1.562.2.4.1.114.7.10		not-accessible	This group contains the provisionable attributes for the Iisp component.
atmIfIispProvEntry	1.3.6.1.4.1.562.2.4.1.114.7.10.1		not-accessible	An entry in the atmIfIispProvTable.
INT atmIfIispVersion	1.3.6.1.4.1.562.2.4.1.114.7.10.1.1	INTEGER	read-write	This attribute indicates which specification the IISP interface complies with. The options are iisp10Sig30 which refers to IISP version 1.0 with 3.0 signalling and iisp10Sig31 which refers to IISP version 1.0 with 3.1 signalling. If this attribute is changed, all switched Vcc components in this interface are cleared due to the fact that the two versions are incompatible.
INT atmIfIispSide	1.3.6.1.4.1.562.2.4.1.114.7.10.1.2	INTEGER	read-write	This attribute indicates which side the interface is, user or network.
U32 atmIfIispSoftPvcRetryPeriod	1.3.6.1.4.1.562.2.4.1.114.7.10.1.3	Unsigned32	read-write	This attribute specifies the time to wait between call set up retries. The resolution is to the nearest 10 seconds. This attribute has been obsoleted and is replaced by the softPvpAndPvcRetryPeriod attribute.
U32 atmIfIispSoftPvpAndPvcRetryPeriod	1.3.6.1.4.1.562.2.4.1.114.7.10.1.4	Unsigned32	read-write	This attribute specifies the time to wait between soft PVP or soft PVC call setup retries. The resolution is to the nearest 10 seconds.
U32 atmIfIispSoftPvpAndPvcHoldOffTime	1.3.6.1.4.1.562.2.4.1.114.7.10.1.5	Unsigned32	read-write	This attribute specifies how long to hold off retries following a release or the connection. The resolution is to the nearest 50 ms.
atmIfIispAcctOptTable	1.3.6.1.4.1.562.2.4.1.114.7.11		not-accessible	This group contains the provisionable attributes for accounting.
atmIfIispAcctOptEntry	1.3.6.1.4.1.562.2.4.1.114.7.11.1		not-accessible	An entry in the atmIfIispAcctOptTable.
OCT atmIfIispAccountCollection	1.3.6.1.4.1.562.2.4.1.114.7.11.1.1	OCTET STRING	read-write	This attribute is used to turn accounting on or off for SVC and SPVC connections. It also specifies the reason(s) for which accounting data is collected: billing, test, study, audit, or force. If the set of reasons is not empty then accounting records will be generated by this interface in the following situations: - on a TODA changeover if TODA is enabled; - every 12 hours (per connection) if TODA is disabled; - on every call clear (a call record with final cell counts). If none of the reasons is present, then accounting will be suppressed. The reason for collection is recorded in the accounting record, in the attribute callingCollectReason or calledCollectReason as appropriate. Description of bits: bill(0) test(1) study(2) audit(3) force(4)
INT atmIfIispAccountConnectionType	1.3.6.1.4.1.562.2.4.1.114.7.11.1.2	INTEGER	read-write	This attribute specifies whether accounting records generated by this interface should be marked as originating, terminating or intermediate. This attribute, in combination with the direction of the call, determines the value of attribute connPointType of the accounting record and may be used by downstream accounting processes to correlate the records. If the value is origTerm then records generated for incoming calls will be marked as originating and records generated for outgoing calls will be marked as terminating. If the value is intermediate then records generated for all calls will be marked as intermediate.
U32 atmIfIispAccountClass	1.3.6.1.4.1.562.2.4.1.114.7.11.1.3	Unsigned32	read-write	This attribute specifies the accounting class associated with the interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingServiceType or calledServiceType as appropriate.
U32 atmIfIispServiceExchange	1.3.6.1.4.1.562.2.4.1.114.7.11.1.4	Unsigned32	read-write	This attribute specifies the data service exchange associated with this interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingDse or calledDse as appropriate.
atmIfVptIisp	1.3.6.1.4.1.562.2.4.1.114.9.6
atmIfVptIispRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.6.1		not-accessible	This entry controls the addition and deletion of atmIfVptIisp components.
atmIfVptIispRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.1.1		not-accessible	A single entry in the table represents a single atmIfVptIisp component.
ROW atmIfVptIispRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.6.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptIisp components. These components can be added and deleted.
STR atmIfVptIispComponentName	1.3.6.1.4.1.562.2.4.1.114.9.6.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptIispStorageType	1.3.6.1.4.1.562.2.4.1.114.9.6.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptIisp tables.
NON atmIfVptIispIndex	1.3.6.1.4.1.562.2.4.1.114.9.6.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptIisp tables.
atmIfVptIispSig	1.3.6.1.4.1.562.2.4.1.114.9.6.3
atmIfVptIispSigRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.6.3.1		not-accessible	This entry controls the addition and deletion of atmIfVptIispSig components.
atmIfVptIispSigRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.3.1.1		not-accessible	A single entry in the table represents a single atmIfVptIispSig component.
ROW atmIfVptIispSigRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.6.3.1.1.1	RowStatus	read-only	This variable is used as the basis for SNMP naming of atmIfVptIispSig components. These components cannot be added nor deleted.
STR atmIfVptIispSigComponentName	1.3.6.1.4.1.562.2.4.1.114.9.6.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptIispSigStorageType	1.3.6.1.4.1.562.2.4.1.114.9.6.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptIispSig tables.
NON atmIfVptIispSigIndex	1.3.6.1.4.1.562.2.4.1.114.9.6.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptIispSig tables.
atmIfVptIispSigVcd	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2
atmIfVptIispSigVcdRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.1		not-accessible	This entry controls the addition and deletion of atmIfVptIispSigVcd components.
atmIfVptIispSigVcdRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.1.1		not-accessible	A single entry in the table represents a single atmIfVptIispSigVcd component.
ROW atmIfVptIispSigVcdRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptIispSigVcd components. These components can be added and deleted.
STR atmIfVptIispSigVcdComponentName	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptIispSigVcdStorageType	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptIispSigVcd tables.
NON atmIfVptIispSigVcdIndex	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptIispSigVcd tables.
atmIfVptIispSigVcdProvTable	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.10		not-accessible	This group contains the provisionable traffic attributes for a control channel.
atmIfVptIispSigVcdProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.10.1		not-accessible	An entry in the atmIfVptIispSigVcdProvTable.
INT atmIfVptIispSigVcdTrafficDescType	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.10.1.1	INTEGER	read-write	This attribute specifies the type of traffic management which is applied to both the transmit and receive direction of this connection as defined in the ATM Forum. The trafficDescType determines the number and meaning of the parameters in the trafficDescParm attribute.
INT atmIfVptIispSigVcdAtmServiceCategory	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.10.1.3	INTEGER	read-write	This attribute specifies the ATM service category for both directions of the connection. The constantBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. The consistent availability of a fixed quantity of bandwidth is considered appropriate for CBR service. Cells which are delayed beyond the value specified by CellTransfer Delay are assumed to be of significantly reduce value to the application. The rtVariableBitRate service category is intended for real time applications, that is those requiring tightly constrained delay and delay variation, as would be appropriate for voice and video applications. Sources are expected to transmit at a rate which varies with time. Equivalently, the source can be described as 'bursty'. Cells which are delayed beyond the value specified by CTD are assumed to be of significantly reduced value to the application. Real time VBR service may support statistical multiplexing of real time sources. The nrtVariableBitRate service category is intended for non-real time applications which have bursty traffic characteristics and which can be characterized in terms of a PCR, SCR, and MBS. For those cells which are transferred within the traffic contract, the application expects a low cell loss ratio. For all connections, it expects a bound on the mean cell transfer delay. Non-real time VBR service may support statistical multiplexing of connections. The unspecifiedBitRate service is intended for non-real time applications; that is, those not requiring tightly constrained delay and delay variation. UBR sources are expected to be bursty. UBR service supports a high degree of statistical multiplexing among sources. UBR service does not specify traffic related service guarantees. No numerical commitments are made with respect to the cell loss ratio experienced by a UBR connection, or as to the cell transfer delay experienced by cells on the connection.
INT atmIfVptIispSigVcdQosClass	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.10.1.21	INTEGER	read-write	This attribute specifies the quality of service for both the forward and backward direction for this connection. Class 1 supports a QOS that meets Service Class A performance requirements (Circuit emulation, constant bit rate video). Class 2 supports a QOS that meets Service Class B performance requirements (Variable bit rate audio and video). Class 3 supports a QOS that meets Service Class C performance requirements (Connection-Oriented Data Transfer). Class 4 supports a QOS that meets Service Class D performance requirements (Connectionless Data Transfer). Class 0 is the unspecified bit rate QOS class; no objective is specified for the performance parameters.
INT atmIfVptIispSigVcdTrafficShaping	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.10.1.50	INTEGER	read-write	This attribute specifies whether this connection uses traffic shaping when transmitting traffic to the ATM interface. When sameAsCa is selected, traffic shaping for this connection is based on the trafficShaping attribute of the connection's service category component under the AtmIf CA. If the service category has traffic shaping enabled, then traffic shaping is enabled for the connection. Note that enabling traffic shaping may have no effect under certain cases. These cases are listed in the description of the trafficShaping operational attribute, which is under the Vcc Tm and Vpc Tm components. When disabled is selected, traffic shaping for this connection is disabled.
INT atmIfVptIispSigVcdUnshapedTransmitQueueing	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.10.1.60	INTEGER	read-write	This attribute only applies when this connection is unshaped. This attribute specifies the transmit queueing method for this connection if it is unshaped. Refer to the unshapedTransmitQueueing attribute under the AtmIf CA service category subcomponent for more details on the meaning of this attribute. When this attribute is set to sameAsCa, the transmit queueing method for the connection is based on the unshapedTransmitQueueing attribute of the connection's service category component under the ConnectionAdministrator. When this attribute is set to common, transmit traffic on this unshaped connection is destined for the common queue. The value sameAsInterface is for migration from previous software releases, but should no longer be used
INT atmIfVptIispSigVcdUsageParameterControl	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.10.1.70	INTEGER	read-write	This attribute specifies whether this connection enforces usage parameter control when receiving traffic from the ATM interface. When sameAsCa is selected, UPC for the connection is based on the usageParameterControl attribute of the connection's service category component under the ConnectionAdministrator. If the service category has UPC enabled, then UPC is enabled for the connection. Note that enabling UPC may have no effect under certain cases. These cases are listed in the description of the usageParameterControl operational attribute, which is under the Vcc Tm or Vpc Tm component. When disabled is selected, UPC for this connection is disabled. The value sameAsInterface is for migration from previous software releases, but should no longer be used
atmIfVptIispSigVcdTdpTable	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.387		not-accessible	This attribute is a vector of five traffic parameters whose meanings are defined by the trafficDescType attribute. The values of peak cell rate (PCR), sustained cell rate (SCR) and requested shaping rate are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for connection admission control (CAC). The value of CDVT is only used for connections where the atmServiceCategory is constantBitRate. For all other values of atmServiceCategory, CDVT is ignored. The values of PCR, SCR and requested shaping rate are used to determine the actual shaping rate where traffic shaping is enabled. When trafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameter 1 must be non-zero. Parameters 2 and 3 must be zero. When trafficDescType is 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. When trafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic; parameter 4 represents the CDVT; and parameter 5 represents the requested shaping rate. A non-zero value in parameter 5 overrides any value in parameter 1. This result is used as the PCR. Parameters 1, 2, and 3 must be non-zero. Parameter 1 must be greater than or equal to parameter 2. Parameter 5 must either be zero (unused) or greater than or equal to parameter 2. Whenever it is valid for PCR to be specified, parameter 5 may also be used to specify a requested shaping rate. A non-zero value in parameter 5 overrides the value in parameter 1 and is used as the peak cell rate in calculations of CAC and shaping rate. For trafficDescType 3 the traffic is shaped at the next rate less than the PCR. For trafficDescType 6, 7, and 8, the traffic is shaped at the highest available rate which is between PCR and SCR. However, if there is no available shaping rate between PCR and SCR, traffic is shaped at the next rate above the PCR.
atmIfVptIispSigVcdTdpEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.387.1		not-accessible	An entry in the atmIfVptIispSigVcdTdpTable.
I32 atmIfVptIispSigVcdTdpIndex	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.387.1.1	Integer32	not-accessible	This variable represents the atmIfVptIispSigVcdTdpTable specific index for the atmIfVptIispSigVcdTdpTable.
U32 atmIfVptIispSigVcdTdpValue	1.3.6.1.4.1.562.2.4.1.114.9.6.3.2.387.1.2	Unsigned32	read-write	This variable represents an individual value for the atmIfVptIispSigVcdTdpTable.
atmIfVptIispSigProvTable	1.3.6.1.4.1.562.2.4.1.114.9.6.3.10		not-accessible	This attribute group contains the provisionable attributes for the Signalling component.
atmIfVptIispSigProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.3.10.1		not-accessible	An entry in the atmIfVptIispSigProvTable.
U32 atmIfVptIispSigVci	1.3.6.1.4.1.562.2.4.1.114.9.6.3.10.1.1	Unsigned32	read-write	This attribute specifies the signalling channel number.
INT atmIfVptIispSigAddressConversion	1.3.6.1.4.1.562.2.4.1.114.9.6.3.10.1.2	INTEGER	read-write	This attribute specifies the address conversion on the outgoing signalling PDUs. The options are none, nativeE164, or nsap. The none option is the default and if this option is chosen then nothing is done to the address information element (IE) in the outgoing signalling message. If nativeE164 option is chosen, then only NSAP encapsulated E.164 addresses with zeros in the ESI are converted to native E.164 format in the outgoing signalling message. If the NSAP address is not encapsulated E.164 or the ESI field is not zeros and the nativeE164 option is chosen, then the call is cleared. If the nsap option is chosen, then native E.164 addresses are converted to NSAP E.164 with zeros in the ESI field; otherwise the address is in NSAP format and is not changed.
atmIfVptIispSigStateTable	1.3.6.1.4.1.562.2.4.1.114.9.6.3.11		not-accessible	This group contains the three OSI State attributes. The descriptions generically indicate what each state attribute implies about the component. Note that not all the values and state combinations described here are supported by every component which uses this group. For component-specific information and the valid state combinations, refer to NTP 241-7001-150, Passport Operations and Maintenance Guide.
atmIfVptIispSigStateEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.3.11.1		not-accessible	An entry in the atmIfVptIispSigStateTable.
INT atmIfVptIispSigAdminState	1.3.6.1.4.1.562.2.4.1.114.9.6.3.11.1.1	INTEGER	read-only	This attribute indicates the OSI Administrative State of the component. The value locked indicates that the component is administratively prohibited from providing services for its users. A Lock or Lock - force command has been previously issued for this component. When the value is locked, the value of usageState must be idle. The value shuttingDown indicates that the component is administratively permitted to provide service to its existing users only. A Lock command was issued against the component and it is in the process of shutting down. The value unlocked indicates that the component is administratively permitted to provide services for its users. To enter this state, issue an Unlock command to this component.
INT atmIfVptIispSigOperationalState	1.3.6.1.4.1.562.2.4.1.114.9.6.3.11.1.2	INTEGER	read-only	This attribute indicates the OSI Operational State of the component. The value enabled indicates that the component is available for operation. Note that if adminState is locked, it would still not be providing service. The value disabled indicates that the component is not available for operation. For example, something is wrong with the component itself, or with another component on which this one depends. If the value is disabled, the usageState must be idle.
INT atmIfVptIispSigUsageState	1.3.6.1.4.1.562.2.4.1.114.9.6.3.11.1.3	INTEGER	read-only	This attribute indicates the OSI Usage State of the component. The value idle indicates that the component is not currently in use. The value active indicates that the component is in use and has spare capacity to provide for additional users. The value busy indicates that the component is in use and has no spare operating capacity for additional users at this time.
atmIfVptIispSigOperTable	1.3.6.1.4.1.562.2.4.1.114.9.6.3.12		not-accessible	This attribute contains the operational attributes for the AtmSignalling component.
atmIfVptIispSigOperEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.3.12.1		not-accessible	An entry in the atmIfVptIispSigOperTable.
U32 atmIfVptIispSigLastTxCauseCode	1.3.6.1.4.1.562.2.4.1.114.9.6.3.12.1.1	Unsigned32	read-only	This attribute indicates the cause code in the last transmitted signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX atmIfVptIispSigLastTxDiagCode	1.3.6.1.4.1.562.2.4.1.114.9.6.3.12.1.2	Hex	read-only	This attribute contains the diagnostic code in the last transmitted signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
U32 atmIfVptIispSigLastRxCauseCode	1.3.6.1.4.1.562.2.4.1.114.9.6.3.12.1.3	Unsigned32	read-only	This attribute contains the cause code in the last received signalling message that contains the CAUSE information element. The cause code is used to describe the reason for generating certain signalling messages.
HEX atmIfVptIispSigLastRxDiagCode	1.3.6.1.4.1.562.2.4.1.114.9.6.3.12.1.4	Hex	read-only	This attribute contains the diagnostic code in the last received signalling message. The diagnostic code is contained in the CAUSE information element and identifies an information element type or timer type. The diagnostic code is present only if a procedural error is detected by the signalling protocol. A diagnostic code is always accompanied by the cause code. If there is no failure, this attribute is set to 0.
atmIfVptIispSigStatsTable	1.3.6.1.4.1.562.2.4.1.114.9.6.3.13		not-accessible	This attribute group contains the statistics associated with the AtmSignalling component.
atmIfVptIispSigStatsEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.3.13.1		not-accessible	An entry in the atmIfVptIispSigStatsTable.
C32 atmIfVptIispSigCurrentConnections	1.3.6.1.4.1.562.2.4.1.114.9.6.3.13.1.1	Counter32	read-only	This attribute indicates the total number of currently active connections.
G32 atmIfVptIispSigPeakConnections	1.3.6.1.4.1.562.2.4.1.114.9.6.3.13.1.2	Gauge32	read-only	This attribute indicates the high water mark of active point-to- point and point-to-multipoint connections.
C32 atmIfVptIispSigSuccessfulConnections	1.3.6.1.4.1.562.2.4.1.114.9.6.3.13.1.3	Counter32	read-only	This attribute counts the total number of switched point-to- point and point-to-multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfVptIispSigFailedConnections	1.3.6.1.4.1.562.2.4.1.114.9.6.3.13.1.4	Counter32	read-only	This attribute counts the total number of switched connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfVptIispSigTxPdus	1.3.6.1.4.1.562.2.4.1.114.9.6.3.13.1.5	Counter32	read-only	This attribute counts the number of transmitted signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfVptIispSigRxPdus	1.3.6.1.4.1.562.2.4.1.114.9.6.3.13.1.6	Counter32	read-only	This attribute counts the number of received signalling PDUs.The counter wraps to 0 when the maximum value is exceeded.
G32 atmIfVptIispSigCurrentPmpConnections	1.3.6.1.4.1.562.2.4.1.114.9.6.3.13.1.7	Gauge32	read-only	This attribute indicates the number of currently active point-to- multipoint connections.
G32 atmIfVptIispSigPeakPmpConnections	1.3.6.1.4.1.562.2.4.1.114.9.6.3.13.1.8	Gauge32	read-only	This attribute indicates the high water mark of active point-to- multipoint connections.
C32 atmIfVptIispSigSuccessfulPmpConnections	1.3.6.1.4.1.562.2.4.1.114.9.6.3.13.1.9	Counter32	read-only	This attribute counts the total number of switched point-to- multipoint connections that were successfully established. The counter wraps to 0 when the maximum value is exceeded.
C32 atmIfVptIispSigFailedPmpConnections	1.3.6.1.4.1.562.2.4.1.114.9.6.3.13.1.10	Counter32	read-only	This attribute counts the number of switched point-to- multipoint connections that were not successfully established.The counter wraps to 0 when the maximum value is exceeded.
G32 atmIfVptIispSigNewCurrentConnections	1.3.6.1.4.1.562.2.4.1.114.9.6.3.13.1.11	Gauge32	read-only	This attribute indicates the total number of currently active point-to- point and point-to-multipoint connections.
atmIfVptIispAddr	1.3.6.1.4.1.562.2.4.1.114.9.6.4
atmIfVptIispAddrRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.6.4.1		not-accessible	This entry controls the addition and deletion of atmIfVptIispAddr components.
atmIfVptIispAddrRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.4.1.1		not-accessible	A single entry in the table represents a single atmIfVptIispAddr component.
ROW atmIfVptIispAddrRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.6.4.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptIispAddr components. These components can be added and deleted.
STR atmIfVptIispAddrComponentName	1.3.6.1.4.1.562.2.4.1.114.9.6.4.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptIispAddrStorageType	1.3.6.1.4.1.562.2.4.1.114.9.6.4.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptIispAddr tables.
STR atmIfVptIispAddrAddressIndex	1.3.6.1.4.1.562.2.4.1.114.9.6.4.1.1.10	AsciiStringIndex	not-accessible	This variable represents an index for the atmIfVptIispAddr tables.
INT atmIfVptIispAddrAddressTypeIndex	1.3.6.1.4.1.562.2.4.1.114.9.6.4.1.1.11	INTEGER	not-accessible	This variable represents an index for the atmIfVptIispAddr tables.
atmIfVptIispAddrTermSP	1.3.6.1.4.1.562.2.4.1.114.9.6.4.2
atmIfVptIispAddrTermSPRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.6.4.2.1		not-accessible	This entry controls the addition and deletion of atmIfVptIispAddrTermSP components.
atmIfVptIispAddrTermSPRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.4.2.1.1		not-accessible	A single entry in the table represents a single atmIfVptIispAddrTermSP component.
ROW atmIfVptIispAddrTermSPRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.6.4.2.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptIispAddrTermSP components. These components can be added and deleted.
STR atmIfVptIispAddrTermSPComponentName	1.3.6.1.4.1.562.2.4.1.114.9.6.4.2.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptIispAddrTermSPStorageType	1.3.6.1.4.1.562.2.4.1.114.9.6.4.2.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptIispAddrTermSP tables.
NON atmIfVptIispAddrTermSPIndex	1.3.6.1.4.1.562.2.4.1.114.9.6.4.2.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptIispAddrTermSP tables.
atmIfVptIispAddrPnniInfo	1.3.6.1.4.1.562.2.4.1.114.9.6.4.3
atmIfVptIispAddrPnniInfoRowStatusTable	1.3.6.1.4.1.562.2.4.1.114.9.6.4.3.1		not-accessible	This entry controls the addition and deletion of atmIfVptIispAddrPnniInfo components.
atmIfVptIispAddrPnniInfoRowStatusEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.4.3.1.1		not-accessible	A single entry in the table represents a single atmIfVptIispAddrPnniInfo component.
ROW atmIfVptIispAddrPnniInfoRowStatus	1.3.6.1.4.1.562.2.4.1.114.9.6.4.3.1.1.1	RowStatus	read-write	This variable is used as the basis for SNMP naming of atmIfVptIispAddrPnniInfo components. These components can be added and deleted.
STR atmIfVptIispAddrPnniInfoComponentName	1.3.6.1.4.1.562.2.4.1.114.9.6.4.3.1.1.2	DisplayString	read-only	This variable provides the component's string name for use with the ASCII Console Interface
STO atmIfVptIispAddrPnniInfoStorageType	1.3.6.1.4.1.562.2.4.1.114.9.6.4.3.1.1.4	StorageType	read-only	This variable represents the storage type value for the atmIfVptIispAddrPnniInfo tables.
NON atmIfVptIispAddrPnniInfoIndex	1.3.6.1.4.1.562.2.4.1.114.9.6.4.3.1.1.10	NonReplicated	not-accessible	This variable represents the index for the atmIfVptIispAddrPnniInfo tables.
atmIfVptIispAddrPnniInfoProvTable	1.3.6.1.4.1.562.2.4.1.114.9.6.4.3.10		not-accessible	This attribute group contains the provisioned attributes relating to PNNI for a PnniInfo component.
atmIfVptIispAddrPnniInfoProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.4.3.10.1		not-accessible	An entry in the atmIfVptIispAddrPnniInfoProvTable.
INT atmIfVptIispAddrPnniInfoScope	1.3.6.1.4.1.562.2.4.1.114.9.6.4.3.10.1.1	INTEGER	read-write	This attribute specifies the scope of the ATM address, which is the highest level up to which this address will be advertised in the PNNI hierarchy. The scope must be set to a value numerically less than or equal to the level of the lowest level peer group containing this node. Setting the scope to 0 will cause the address to be advertised globally within this PNNI routing domain.
INT atmIfVptIispAddrPnniInfoReachability	1.3.6.1.4.1.562.2.4.1.114.9.6.4.3.10.1.2	INTEGER	read-write	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
atmIfVptIispAddrOperTable	1.3.6.1.4.1.562.2.4.1.114.9.6.4.10		not-accessible	This attribute group contains the operational attributes for the Address component.
atmIfVptIispAddrOperEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.4.10.1		not-accessible	An entry in the atmIfVptIispAddrOperTable.
INT atmIfVptIispAddrScope	1.3.6.1.4.1.562.2.4.1.114.9.6.4.10.1.1	INTEGER	read-only	This attribute indicates the scope of the ATM address, which is the highest level to which this address will be advertised in the PNNI hierarchy. If no PnniInfo subcomponent has been provisioned, then the scope will default to the level of this node in the PNNI hierarchy. If this node does not participate in a PNNI hierarchy, then this attribute will have the value of -1.
INT atmIfVptIispAddrReachability	1.3.6.1.4.1.562.2.4.1.114.9.6.4.10.1.2	INTEGER	read-only	This attribute indicates whether the address is internal or exterior. An internal reachable address is an address of a destination that is directly attached to the logical node advertising the address. An exterior reachable address is an address that can be reached through a PNNI routing domain, but which is not located in that PNNI routing domain.
atmIfVptIispProvTable	1.3.6.1.4.1.562.2.4.1.114.9.6.10		not-accessible	This group contains the provisionable attributes for the Iisp component.
atmIfVptIispProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.10.1		not-accessible	An entry in the atmIfVptIispProvTable.
INT atmIfVptIispVersion	1.3.6.1.4.1.562.2.4.1.114.9.6.10.1.1	INTEGER	read-write	This attribute indicates which specification the IISP interface complies with. The options are iisp10Sig30 which refers to IISP version 1.0 with 3.0 signalling and iisp10Sig31 which refers to IISP version 1.0 with 3.1 signalling. If this attribute is changed, all switched Vcc components in this interface are cleared due to the fact that the two versions are incompatible.
INT atmIfVptIispSide	1.3.6.1.4.1.562.2.4.1.114.9.6.10.1.2	INTEGER	read-write	This attribute indicates which side the interface is, user or network.
U32 atmIfVptIispSoftPvcRetryPeriod	1.3.6.1.4.1.562.2.4.1.114.9.6.10.1.3	Unsigned32	read-write	This attribute specifies the time to wait between call set up retries. The resolution is to the nearest 10 seconds. This attribute has been obsoleted and is replaced by the softPvpAndPvcRetryPeriod attribute.
U32 atmIfVptIispSoftPvpAndPvcRetryPeriod	1.3.6.1.4.1.562.2.4.1.114.9.6.10.1.4	Unsigned32	read-write	This attribute specifies the time to wait between soft PVP or soft PVC call setup retries. The resolution is to the nearest 10 seconds.
U32 atmIfVptIispSoftPvpAndPvcHoldOffTime	1.3.6.1.4.1.562.2.4.1.114.9.6.10.1.5	Unsigned32	read-write	This attribute specifies how long to hold off retries following a release or the connection. The resolution is to the nearest 50 ms.
atmIfVptIispAcctOptTable	1.3.6.1.4.1.562.2.4.1.114.9.6.11		not-accessible	This group contains the provisionable attributes for accounting.
atmIfVptIispAcctOptEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.11.1		not-accessible	An entry in the atmIfVptIispAcctOptTable.
OCT atmIfVptIispAccountCollection	1.3.6.1.4.1.562.2.4.1.114.9.6.11.1.1	OCTET STRING	read-write	This attribute is used to turn accounting on or off for SVC and SPVC connections. It also specifies the reason(s) for which accounting data is collected: billing, test, study, audit, or force. If the set of reasons is not empty then accounting records will be generated by this interface in the following situations: - on a TODA changeover if TODA is enabled; - every 12 hours (per connection) if TODA is disabled; - on every call clear (a call record with final cell counts). If none of the reasons is present, then accounting will be suppressed. The reason for collection is recorded in the accounting record, in the attribute callingCollectReason or calledCollectReason as appropriate. Description of bits: bill(0) test(1) study(2) audit(3) force(4)
INT atmIfVptIispAccountConnectionType	1.3.6.1.4.1.562.2.4.1.114.9.6.11.1.2	INTEGER	read-write	This attribute specifies whether accounting records generated by this interface should be marked as originating, terminating or intermediate. This attribute, in combination with the direction of the call, determines the value of attribute connPointType of the accounting record and may be used by downstream accounting processes to correlate the records. If the value is origTerm then records generated for incoming calls will be marked as originating and records generated for outgoing calls will be marked as terminating. If the value is intermediate then records generated for all calls will be marked as intermediate.
U32 atmIfVptIispAccountClass	1.3.6.1.4.1.562.2.4.1.114.9.6.11.1.3	Unsigned32	read-write	This attribute specifies the accounting class associated with the interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingServiceType or calledServiceType as appropriate.
U32 atmIfVptIispServiceExchange	1.3.6.1.4.1.562.2.4.1.114.9.6.11.1.4	Unsigned32	read-write	This attribute specifies the data service exchange associated with this interface. Its meaning is determined by the network operator. Its value is simply recorded in the accounting records generated by this interface, in the attribute callingDse or calledDse as appropriate.
atmIfVptIispVProvTable	1.3.6.1.4.1.562.2.4.1.114.9.6.12		not-accessible	This group contains the provisionable attributes for the Iisp component which are specific to virtual IISP interfaces.
atmIfVptIispVProvEntry	1.3.6.1.4.1.562.2.4.1.114.9.6.12.1		not-accessible	An entry in the atmIfVptIispVProvTable.
U32 atmIfVptIispVpci	1.3.6.1.4.1.562.2.4.1.114.9.6.12.1.1	Unsigned32	read-write	This attribute specifies the Virtual Path Connection Identifier (VPCI) to be used between this signalling entity and its peer. The VPCI of the peer virtual IISP must have the same value for switched connections to be set up across the interface.
atmIispMIB	1.3.6.1.4.1.562.2.4.2.70
atmIispGroup	1.3.6.1.4.1.562.2.4.2.70.1
atmIispGroupBE	1.3.6.1.4.1.562.2.4.2.70.1.5
atmIispGroupBE00	1.3.6.1.4.1.562.2.4.2.70.1.5.1
atmIispGroupBE00A	1.3.6.1.4.1.562.2.4.2.70.1.5.1.2
atmIispCapabilities	1.3.6.1.4.1.562.2.4.2.70.3
atmIispCapabilitiesBE	1.3.6.1.4.1.562.2.4.2.70.3.5
atmIispCapabilitiesBE00	1.3.6.1.4.1.562.2.4.2.70.3.5.1
atmIispCapabilitiesBE00A	1.3.6.1.4.1.562.2.4.2.70.3.5.1.2

RFC description

ATM Interim Inter-switch Signaling Protocol (IISP) interface management. Manages ATM IISP components and VCC connections.

Start monitoring Nortel Magellan Passport ATM switch (IISP inter-switch signaling) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Nortel-Magellan-Passport-AtmIispMIB

What Is Nortel-Magellan-Passport-AtmIispMIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description