All MIBs › MRV-IN-REACH-LAT-MIB
Category: Console Servers
Description: Manages MRV In-Reach LAT protocol service and session configuration.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is MRV-IN-REACH-LAT-MIB?
MRV-IN-REACH-LAT-MIB is a vendor-specific MIB from MRV Communications defining management objects for the LAT (Local Area Transport, a DEC/legacy terminal networking protocol) service on its In-Reach console-server/network-access products. It belongs to the legacy terminal-networking support area of MRV's product line. It exposes configuration and session-related objects for LAT services offered by the device, letting administrators manage LAT service definitions and connections. Its main monitoring value is confirming the software-level operational status of the LAT service and its active sessions on the unit, rather than physical hardware health. It builds on the base MRV In-Reach system MIB framework and enterprise structure, and is typically deployed on In-Reach terminal/console servers supporting legacy DEC/VMS-connected terminal equipment, where administrators can download the MRV-IN-REACH-LAT-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in MRV-IN-REACH-LAT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- MRV In-Reach console/terminal server
Monitoring Examples
No sample_objects were supplied for this MIB in the source data, so specific object/table names cannot be cited directly. In practice, an administrator would use this module's LAT service and session objects to verify that configured LAT services are active and that expected terminal sessions are established through the In-Reach unit. Session drops or unexpected LAT service state changes would be the class of anomaly this MIB is designed to reveal, though precise object names cannot be given without further data.
What Can Be Monitored
- LAT service configuration
- LAT session status
This MIB depends on
Related MIBs
Imported Objects
From MRV-IN-REACH-PRODUCT-DIVISION-MIB
| mrvInReachProductDivision | OBJECT-IDENTITY |
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| TimeTicks |
From RFC1213-MIB
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| CTR latAddressChange | 1.3.6.1.4.1.33.3.17 | Counter | read-only | Number of times a service announcement contained a node name already in the visible service table but with a different address. Corresponds directly to the value labeled 'Multiple Node Addresses:' in the SERVER COUNTERS display. |
| INT latAnnounceServices | 1.3.6.1.4.1.33.3.1 | INTEGER | read-write | Control for automatic, periodic announcement of local services to the network. Corresponds directly to SERVER ANNOUNCEMENTS and the presence of the label 'Announcements' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| INT latCircuitTimer | 1.3.6.1.4.1.33.3.2 | INTEGER | read-write | Number of milleseconds to collect port input data before sending it to the host. Corresponds directly to SERVER CIRCUIT TIMER and the value labeled 'Circuit Timer:' in the SERVER CHARACTERISTICS display. |
| INT latGroupPurge | 1.3.6.1.4.1.33.3.10 | INTEGER | read-write | Control for automatic deletion of all node table entries when latServiceGroups or latPortCurrentGroups is changed. Corresponds directly to SERVER PURGE GROUP and the presence of the label 'Purge Group' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| INT latIdentificationLengthLimit | 1.3.6.1.4.1.33.3.3 | INTEGER | read-write | Maximum number of characters to store in the instances of latVisibleServiceIdentification. Corresponds directly to SERVER IDENTIFICATION SIZE and the value labeled 'Identification Size:' in the SERVER CHARACTERISTICS display. |
| INT latImmediateAck | 1.3.6.1.4.1.33.3.28 | INTEGER | read-write | Control for LAT to provide an immediate ACK, and not to wait for the timer to expire. Corresponds directly to SERVER LAT IMMEDIATE ACK and the presence of the label 'LAT Immediate Ack following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| CTR latInBadMessages | 1.3.6.1.4.1.33.3.20 | Counter | read-only | Number of LAT messages received with invalid format. Corresponds directly to the value labeled 'Illegal Messages Rcv'd:' in the SERVER COUNTERS display. |
| CTR latInBadMulticasts | 1.3.6.1.4.1.33.3.22 | Counter | read-only | Number of multicast LAT messages received with invalid format. Corresponds directly to the value labeled 'Illegal Multicasts Rcv'd:' in the SERVER COUNTERS display. |
| CTR latInBadSlots | 1.3.6.1.4.1.33.3.21 | Counter | read-only | Number of LAT messages received with invalid slot format. Corresponds directly to the value labeled 'Illegal Slots Rcv'd:' in the SERVER COUNTERS display. |
| CTR latInDuplicates | 1.3.6.1.4.1.33.3.18 | Counter | read-only | Number of duplicate LAT messages received. Corresponds directly to the value labeled 'Duplicates Received:' in the SERVER COUNTERS display. |
| CTR latInMessages | 1.3.6.1.4.1.33.3.13 | Counter | read-only | Number of LAT messages received. Corresponds directly to the value labeled 'Messages Received:' in the SERVER COUNTERS display. |
| CTR latInSessionsAccepted | 1.3.6.1.4.1.33.3.15 | Counter | read-only | Number of incoming LAT session connection attempts accepted. Corresponds directly to the value labeled 'Solicitations Accepted:' in the SERVER COUNTERS display. |
| CTR latInSessionsRejected | 1.3.6.1.4.1.33.3.16 | Counter | read-only | Number of incoming LAT session connection attempts rejected. Corresponds directly to the value labeled 'Solicitations Rejected:' in the SERVER COUNTERS display. |
| INT latKeepaliveTimer | 1.3.6.1.4.1.33.3.4 | INTEGER | read-write | Number of seconds of inactivity before sending a null message to the host. Corresponds directly to SERVER KEEPALIVE TIMER and the value labeled 'Keepalive Timer:' in the SERVER CHARACTERISTICS display. |
| OCT latLocalServiceGroups | 1.3.6.1.4.1.33.3.9 | OCTET STRING | read-write | The list of group numbers allowed to use local services, where a group number is in the range 0-255. The OCTET STRING contains a bitmap, with one bit for each group. Corresponding bit numbers start with 0 as the high-order bit of the first octet. Corresponds directly to SERVER SERVICE GROUPS and the value labeled 'Service Groups:' in the SERVER CHARACTERISTICS display. |
| INT latMulticastTimer | 1.3.6.1.4.1.33.3.5 | INTEGER | read-write | Number of seconds between transmission of local service announcements. Corresponds directly to SERVER MULTICAST TIMER and the value labeled 'Multicast Timer:' in the SERVER CHARACTERISTICS display. |
| OCT latNodeAddress | 1.3.6.1.4.1.33.3.26.1.4 | OCTET STRING | read-only | Ethernet address of the node. Corresponds directly to the value labeled 'Address:' in the NODE STATUS display. |
| CTR latNodeAddressChange | 1.3.6.1.4.1.33.3.26.1.17 | Counter | read-only | The number of times a LAT message multicast by the node had a different Ethernet address from the previous time. Corresponds directly to the value labeled 'Multiple Node Addresses:' in the NODE COUNTERS display. |
| GAU latNodeConnectedSessions | 1.3.6.1.4.1.33.3.26.1.3 | Gauge | read-only | Number of connected sessions to the node. Corresponds directly to the number with the value 'Connected', labeled 'Status' in the NODE STATUS display. |
| INT latNodeDataLinkFrame | 1.3.6.1.4.1.33.3.26.1.5 | INTEGER | read-only | Maximum Ethernet frame used by the node. Corresponds directly to the value labeled 'Data Link Frame Size:' in the NODE STATUS display. |
| latNodeEntry | 1.3.6.1.4.1.33.3.26.1 | not-accessible | Parameter values for a node entry. | |
| OCT latNodeGroups | 1.3.6.1.4.1.33.3.26.1.7 | OCTET STRING | read-only | The list of group numbers to which the node belongs, where a group number is in the range 0-255. The OCTET STRING contains a bitmap, with one bit for each group. Corresponding bit numbers start with 0 as the high-order bit of the first octet. Corresponds directly to the value labeled 'Node Groups:' in the NODE STATUS display. |
| STR latNodeIdentification | 1.3.6.1.4.1.33.3.26.1.6 | DisplayString | read-only | Text that identifies the node. The size is subject to limitation by latIdentificationLengtLimit. Corresponds directly to the value labeled 'Identification' in the NODE STATUS display. |
| CTR latNodeInBadMessages | 1.3.6.1.4.1.33.3.26.1.20 | Counter | read-only | The number of LAT message received from the node with invalid format. Corresponds directly to the value labeled 'Illegal Messages Received:' in the NODE COUNTERS display. |
| CTR latNodeInBadSlots | 1.3.6.1.4.1.33.3.26.1.21 | Counter | read-only | The number of LAT slots received from the node with invalid format. Corresponds directly to the value labeled 'Illegal Slots Received:' in the NODE COUNTERS display. |
| CTR latNodeInBytes | 1.3.6.1.4.1.33.3.26.1.15 | Counter | read-only | The total number of bytes received from the node, including Ethernet overhead. Corresponds directly to the value labeled 'Bytes Received:' in the NODE COUNTERS display. |
| CTR latNodeInDuplicates | 1.3.6.1.4.1.33.3.26.1.18 | Counter | read-only | The number of duplicate LAT message received from the node. Corresponds directly to the value labeled 'Duplicates Received:' in the NODE COUNTERS display. |
| CTR latNodeInMessages | 1.3.6.1.4.1.33.3.26.1.11 | Counter | read-only | The number of LAT messages received from the node. Corresponds directly to the value labeled 'Messages Received:' in the NODE COUNTERS display. |
| CTR latNodeInSessionsAccepted | 1.3.6.1.4.1.33.3.26.1.22 | Counter | read-only | The number of LAT session connection attempts received from the node and accepted. Corresponds directly to the value labeled 'Solicitations Accepted:' in the NODE COUNTERS display. |
| CTR latNodeInSessionsRejected | 1.3.6.1.4.1.33.3.26.1.23 | Counter | read-only | The number of LAT session connection attempts received from the node and rejected. Corresponds directly to the value labeled 'Solicitations Rejected:' in the NODE COUNTERS display. |
| CTR latNodeInSlots | 1.3.6.1.4.1.33.3.26.1.13 | Counter | read-only | The number of LAT slots received from the node. Corresponds directly to the value labeled 'Slots Received:' in the NODE COUNTERS display. |
| INT latNodeLimit | 1.3.6.1.4.1.33.3.6 | INTEGER | read-write | Maximum number of service nodes to keep in the node table. Corresponds directly to SERVER NODE LIMIT and the value labeled 'Node Limit:' in the SERVER CHARACTERISTICS display. |
| STR latNodeName | 1.3.6.1.4.1.33.3.26.1.1 | DisplayString | read-only | The name of a node. Corresponds directly to the value labeled 'Node:' in the NODE STATUS display. |
| CTR latNodeOutBytes | 1.3.6.1.4.1.33.3.26.1.16 | Counter | read-only | The total number of bytes sent to the node, including Ethernet overhead. Corresponds directly to the value labeled 'Bytes Transmitted:' in the NODE COUNTERS display. |
| CTR latNodeOutMessages | 1.3.6.1.4.1.33.3.26.1.12 | Counter | read-only | The number of LAT messages sent to the node. Corresponds directly to the value labeled 'Messages Transmitted:' in the NODE COUNTERS display. |
| CTR latNodeOutRetransmits | 1.3.6.1.4.1.33.3.26.1.19 | Counter | read-only | The number of LAT message retransmitted to the node due to lack of acknowledgement. Corresponds directly to the value labeled 'Messages Re-transmitted:' in the NODE COUNTERS display. |
| CTR latNodeOutSlots | 1.3.6.1.4.1.33.3.26.1.14 | Counter | read-only | The number of LAT slots sent to the node. Corresponds directly to the value labeled 'Slots Transmitted:' in the NODE COUNTERS display. |
| INT latNodePurge | 1.3.6.1.4.1.33.3.11 | INTEGER | read-write | Control for automatic deletion of all node table entries with status 'reachable' when the number of entries exceeds latNodeLimit. Corresponds directly to SERVER PURGE NODE and the presence of the label 'Purge Node' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| GAU latNodeServiceNumber | 1.3.6.1.4.1.33.3.26.1.8 | Gauge | read-only | Number of entries for the node in the node service table. Corresponds indirectly to the list of services in the NODE STATUS display. |
| CTR latNodesRejected | 1.3.6.1.4.1.33.3.12 | Counter | read-only | Number of nodes not added to the node table because there was no room. Corresponds directly to the value labeled 'Discarded Nodes:' in the SERVER STATUS display. |
| INT latNodeStatus | 1.3.6.1.4.1.33.3.26.1.2 | INTEGER | read-only | Status of communication with the node. Corresponds directly to the value labeled 'Status' in the NODE STATUS display. |
| latNodeTable | 1.3.6.1.4.1.33.3.26 | not-accessible | A list of node entries. | |
| INT latNodeZero | 1.3.6.1.4.1.33.3.26.1.9 | INTEGER | read-write | Control to zero counters kept for the node. In response to a get-request or get-next-request, the agent always returns 'ready' for this value. Setting the value to 'ready' has no effect. Setting it to 'execute' causes all the system's counters to be zeroed. Corresponds to the ZERO NODE command. |
| TIK latNodeZeroTime | 1.3.6.1.4.1.33.3.26.1.10 | TimeTicks | read-only | The number of hundredths of a second since the most recent zeroing of the counters kept for the node, such as through execution of sysZeroAll or latNodeZero. Corresponds directly to the value labeled 'Seconds Since Zeroed:' in the NODE COUNTERS display. |
| INT latNumber | 1.3.6.1.4.1.33.3.7 | INTEGER | read-write | An arbitrary number assigned and used for administrative purposes. Corresponds directly to SERVER NUMBER and the value labeled 'Number:' in the SERVER CHARACTERISTICS display. |
| INT latOfferedServiceAllowConnections | 1.3.6.1.4.1.33.3.24.1.3 | INTEGER | read-write | Control for allowing incoming connections to the service. Corresponds directly to SERVICE CONNECTIONS and the presence of the label 'Connections' following the label 'Enabled Characteristics:' in the SERVICE CHARACTERISTICS display. |
| latOfferedServiceEntry | 1.3.6.1.4.1.33.3.24.1 | not-accessible | Parameter values for an offered service entry. | |
| INT latOfferedServiceEnvironmentalManager | 1.3.6.1.4.1.33.3.24.1.8 | INTEGER | read-write | Control indicating whether Environmental Management services are offered. |
| STR latOfferedServiceIdentification | 1.3.6.1.4.1.33.3.24.1.4 | DisplayString | read-write | Text to identify a service. Corresponds directly to SERVICE IDENTIFICATION and the value labeled 'Identification:' in the SERVICE CHARACTERISTICS display. |
| STR latOfferedServiceName | 1.3.6.1.4.1.33.3.24.1.1 | DisplayString | read-only | The name of an offered service. Corresponds directly to the name in a SERVICE command and the value labeled 'Service:' in the SERVICE CHARACTERISTICS display. |
| STR latOfferedServicePassword | 1.3.6.1.4.1.33.3.24.1.5 | DisplayString | read-write | The password a user must supply to use the service. Corresponds directly to SERVICE PASSWORD and the presence of the label 'Password' following the label 'Enabled Characteristics:' in the SERVICE CHARACTERISTICS display. When setting this value, the management system must supply eight octets, filling with zeros from the first octet. That is, the value '1ab42' would be expressed as '0.0.0.0.0.1.ab.42'. Setting the value to zero disables the password check. When returning this value, the agent always returns a zero length OCTET STRING. |
| OCT latOfferedServicePortMap | 1.3.6.1.4.1.33.3.24.1.6 | OCTET STRING | read-write | The list of character ports offer the service. The OCTET STRING contains a bitmap, with one bit for each port, and enough octets for all the ports on the system. Port numbers are as defined for charPortIndex in the Character MIB [11]. Corresponding bit numbers start with 1 as the high-order bit of the first octet. Corresponds directly to port-list portion of SERVICE PORTS and the value labeled 'Ports:' in the SERVICE CHARACTERISTICS display. |
| INT latOfferedServiceQueuing | 1.3.6.1.4.1.33.3.24.1.7 | INTEGER | read-write | Control for allowing queuing of incoming connections to the service when the service is busy. Corresponds directly to SERVICE QUEUE and the presence of the label 'Queuing' following the label 'Enabled Characteristics:' in the SERVICE CHARACTERISTICS display. |
| INT latOfferedServiceStatus | 1.3.6.1.4.1.33.3.24.1.2 | INTEGER | read-write | The status of the entry. Set to 'invalid' to remove the entry, which corresponds directly to the CLEAR SERVICE command. Actual removal of the entry is implementation specific. |
| latOfferedServiceTable | 1.3.6.1.4.1.33.3.24 | not-accessible | A list of offered service entries. | |
| CTR latOutMessages | 1.3.6.1.4.1.33.3.14 | Counter | read-only | Number of LAT messages sent. Corresponds directly to the value labeled 'Messages Transmitted:' in the SERVER COUNTERS display. |
| CTR latOutRetransmits | 1.3.6.1.4.1.33.3.19 | Counter | read-only | Number of LAT messages retransmitted due to no acknowledgement. Corresponds directly to the value labeled 'Messages Re-transmitted:' in the SERVER COUNTERS display. |
| OCT latPortAuthorizedGroups | 1.3.6.1.4.1.33.3.23.1.2 | OCTET STRING | read-write | The list of group numbers to which the port is allowed to set access, where a group number is in the range 0-255. The OCTET STRING contains a bitmap, with one bit for each group. Corresponding bit numbers start with 0 as the high-order bit of the first octet. Corresponds directly to PORT AUTHORIZED GROUPS and the value labeled 'Authorized Groups:' in the PORT CHARACTERISTICS display. |
| INT latPortAutoPrompt | 1.3.6.1.4.1.33.3.23.1.3 | INTEGER | read-write | Control for automatic stimulation of a host prompt upon forming a new session. Corresponds directly to PORT AUTOPROMPT and the presence of the label 'Autoprompt' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| OCT latPortCurrentGroups | 1.3.6.1.4.1.33.3.23.1.4 | OCTET STRING | read-write | The list of group numbers to which the port currently has set access, where a group number is in the range 0-255. The OCTET STRING contains a bitmap, with one bit for each group. Corresponding bit numbers start with 0 as the high-order bit of the first octet. Corresponds directly to PORT GROUPS and the value labeled 'Groups:' in the PORT CHARACTERISTICS display. |
| latPortEntry | 1.3.6.1.4.1.33.3.23.1 | not-accessible | LAT parameter values for a port. | |
| INT latPortIndex | 1.3.6.1.4.1.33.3.23.1.1 | INTEGER | read-only | An index value that uniquely identifies a port. The port identified by a particular value of this index is the same port as identified by charPortIndex in the Character MIB [11]. |
| INT latPortRemoteModification | 1.3.6.1.4.1.33.3.23.1.5 | INTEGER | read-write | Control to allow the remote system to modify certain physical port characteristics. Corresponds directly to PORT REMOTE MODIFICATION and the presence of the label 'Remote Modification' following the label 'Enabled Characteristics:' in the PORT CHARACTERISTICS display. |
| latPortTable | 1.3.6.1.4.1.33.3.23 | not-accessible | A list of LAT character port entries. | |
| INT latRetransmitLimit | 1.3.6.1.4.1.33.3.8 | INTEGER | read-write | Maximum number of times to retransmit an unacknowledged message. Corresponds directly to SERVER RETRANSMIT LIMIT and the value labeled 'Retransmit Limit:' in the SERVER CHARACTERISTICS display. |
| INT latSolicits | 1.3.6.1.4.1.33.3.27 | INTEGER | read-write | Control for multicast solicitation of LAT services. Corresponds directly to SERVER LAT SOLICITAIONS and the presence of the label 'LAT SOLICITATIONS' following the label 'Enabled Characteristics:' in the SERVER CHARACTERISTICS display. |
| GAU latVisibleServiceConnectedSessions | 1.3.6.1.4.1.33.3.25.1.4 | Gauge | read-only | Number of connected sessions to the service. Corresponds directly to the number with the value 'Connected', labeled 'Status' in the SERVICE SUMMARY display. |
| latVisibleServiceEntry | 1.3.6.1.4.1.33.3.25.1 | not-accessible | Parameter values for a visible service entry. | |
| STR latVisibleServiceIdentification | 1.3.6.1.4.1.33.3.25.1.5 | DisplayString | read-only | Text to identify a service. The length is subject to limitation by latIdentificationLengthLimit. Corresponds directly to the value labeled 'Identification:' in the SERVICE SUMMARY display. |
| STR latVisibleServiceName | 1.3.6.1.4.1.33.3.25.1.1 | DisplayString | read-only | The name of a visible service. Corresponds directly to the name in a SERVICE command and the value labeled 'Service Name' in the SERVICE SUMMARY display. |
| STR latVisibleServiceNode | 1.3.6.1.4.1.33.3.25.1.3 | DisplayString | read-only | Name of a node offering the service. Corresponds directly to the value labeled Node Name in the SERVICE STATUS display. |
| GAU latVisibleServiceRating | 1.3.6.1.4.1.33.3.25.1.6 | Gauge | read-only | Relative capacity of the service to accept additional sessions. Corresponds directly to value labeled Rating in the SERVICE STATUS display. |
| INT latVisibleServiceStatus | 1.3.6.1.4.1.33.3.25.1.2 | INTEGER | read-only | Status of communication with the service. Corresponds directly to the value labeled 'Status' in the SERVICE SUMMARY display. |
| latVisibleServiceTable | 1.3.6.1.4.1.33.3.25 | not-accessible | A list of visible service entries. | |
| xLat | 1.3.6.1.4.1.33.3 |
RFC description
Manages LAT (Local Area Transport) protocol settings on MRV In-Reach systems including service announcements and circuit timing parameters.
Start monitoring MRV In-Reach console/terminal server (LAT service) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.