All MIBs › MICOM-ISDN-MIB
Category: WAN
Description: Monitors ISDN BRI/PRI line status and call statistics on Micom WAN access equipment.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is MICOM-ISDN-MIB?
MICOM-ISDN-MIB is a vendor MIB for Micom (NetVantage/Compatible Systems lineage) WAN access equipment that terminates ISDN BRI and PRI lines. It exposes configuration and status data for ISDN basic-rate interfaces, D-channel signaling protocols, calling/sub-address information, and LAPD link-layer state on the device's ISDN ports. Administrators use it to monitor hardware and line status directly — line topology and signal mode of each BRI port, signaling protocol and LAPD link status (up/down), and dial control configuration reveal whether an ISDN circuit is properly synchronized or has dropped. It complements standard interface MIBs (IF-MIB) by adding ISDN-specific signaling detail not covered by generic interface counters. It is typically deployed on legacy WAN routers/access concentrators using ISDN as a primary or backup dial-up link in branch-office networks, where administrators can download the MICOM-ISDN-MIB file to load into their MIB browser before polling these devices.
IPNetwork Monitor allows you to monitor SNMP objects defined in MICOM-ISDN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Micom WAN access router/multiplexer
- ISDN BRI/PRI access equipment
Monitoring Examples
An operator would poll nvmIsdnBasicRateTable/nvmIsdnBasicRateEntry to check nvmIsdnBasicRateLineTopology and nvmIsdnBasicRateSignalMode for each BRI port, confirming the line is provisioned as point-to-point or point-to-multipoint and correctly synchronized. Polling nvmIsdnSignalingTable's nvmIsdnSignalingProtocol and mcmIsdnLapdTable would show whether the D-channel LAPD link is established; a LAPD link stuck in an establishing state typically indicates a carrier provisioning mismatch or physical layer fault. nvmIsdnSignalingInfoTrapEnable lets an admin enable traps so signaling state changes (e.g., call setup failures) are reported proactively rather than discovered via polling.
What Can Be Monitored
- ISDN BRI line topology
- D-channel signaling protocol
- LAPD link status
- calling/sub-address info
- dial control configuration
- signaling trap notifications
This MIB depends on
Related MIBs
Imported Objects
From DIAL-CONTROL-MIB
| callActiveIndex | OBJECT-TYPE |
| callActiveSetupTime | OBJECT-TYPE |
| dialCtlPeerCfgId | OBJECT-TYPE |
From IF-MIB
| ifIndex | OBJECT-TYPE |
From MICOM-OSCAR-MIB
| micom-oscar |
From RFC-1212
| OBJECT-TYPE |
From RFC1213-MIB
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| configuration | 1.3.6.1.4.1.335.1.4.24.1 | |||
| control | 1.3.6.1.4.1.335.1.4.24.2 | |||
| INT mcmCallActiveGaugeAction | 1.3.6.1.4.1.335.1.4.24.2.4.1.1 | INTEGER | write-only | NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ Setting this object to reset(1) will zero \ the values of a specific row of gauges in \ the Dial Control Call Active table defined \ in the MIB file rfc2128.mib.; HELP = When set to reset(1), a row containing \ the following counter objects are reset: \ callActiveChargedUnits \ callActiveTransmitPackets \ callActiveTransmitBytes \ callActiveReceivePackets \ callActiveReceiveBytes; CAPABILITIES = ; |
| mcmCallActiveGaugeEntry | 1.3.6.1.4.1.335.1.4.24.2.4.1 | not-accessible | NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ An entry in the Dial Control Call Active gauge \ reset table.; HELP = ; CAPABILITIES = ; | |
| mcmCallActiveGaugeTable | 1.3.6.1.4.1.335.1.4.24.2.4 | not-accessible | NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ The Dial Control Call Active gauge reset table.; HELP = ; CAPABILITIES = NET_OPER, VPN_OPER; | |
| INT mcmCallHistoryTableResetCmd | 1.3.6.1.4.1.335.1.4.24.2.5 | INTEGER | write-only | NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ Setting this object to reset(1) will clear \ the entire Dial Control Call History table \ defined in the MIB file rfc2128.mib.; HELP = ; CAPABILITIES = NET_OPER, VPN_OPER; |
| INT mcmDialCtlPeerCfgBchannel | 1.3.6.1.4.1.335.1.4.24.1.8.1.2 | INTEGER | read-only | NAME = ; DESC = The value of this object specifies the B channel to be used \ for leased lines. (Operational); HELP = Note: 0 = 'any'. This managed object is not part of the \ original Dial Control MIB (RFC2128). This proprietary \ object was added for ICM purposes.; CAPABILITIES = ; |
| mcmDialCtlPeerCfgEntry | 1.3.6.1.4.1.335.1.4.24.1.8.1 | not-accessible | NAME = ; DESC = An entry in the Peer Group Table. (Extension to \ Peer Group table in RFC2128 MIB. (Operational);\ HELP = ; CAPABILITIES = ; | |
| INT mcmDialCtlPeerCfgId | 1.3.6.1.4.1.335.1.4.24.1.8.1.1 | INTEGER | read-only | NAME = ; DESC = This object identifies a single peer. There may \ be several entries in this table for one peer, \ defining different ways of reaching this peer. \ Thus, there may be several entries in this table \ with the same value of mcmDialCtlPeerCfgId. \ Multiple entries for one peer may be used to support \ multilink as well as backup lines. \ A single peer will be identified by a unique value \ of this object. Several entries for one peer MUST \ have the same value of mcmDialCtlPeerCfgId, but different \ ifEntries and thus different values of ifIndex. \ (Operational); HELP = ; CAPABILITIES = ; |
| mcmDialCtlPeerCfgTable | 1.3.6.1.4.1.335.1.4.24.1.8 | not-accessible | NAME = ; DESC = The list of peers from which the managed device \ will accept calls or to which it will place them. \ This table is an extension to the Peer Group table \ resident in the RFC2128 MIB. (Operational) HELP = ; CAPABILITIES = NET_CFG, VPN_DISP ; | |
| INT mcmDialCtlPeerStatsGaugeAction | 1.3.6.1.4.1.335.1.4.24.2.3.1.1 | INTEGER | write-only | NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ Setting this object to reset(1) will zero \ the values of a specific row of gauges in \ the Dial Control Peer Statistics table defined \ in the MIB file rfc2128.mib.; HELP = When set to reset(1), a row containing \ the following counter objects are reset: \ dialCtlPeerStatsConnectTime \ dialCtlPeerStatsChargedUnits \ dialCtlPeerStatsSuccessCalls \ dialCtlPeerStatsFailCalls \ dialCtlPeerStatsAcceptCalls \ dialCtlPeerStatsRefuseCalls; CAPABILITIES = ; |
| mcmDialCtlPeerStatsGaugeEntry | 1.3.6.1.4.1.335.1.4.24.2.3.1 | not-accessible | NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ An entry in the Dial Control Peer Statistics gauge \ reset table.; HELP = ; CAPABILITIES = ; | |
| mcmDialCtlPeerStatsGaugeTable | 1.3.6.1.4.1.335.1.4.24.2.3 | not-accessible | NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ The Dial Control Peer Statistics gauge reset table.; HELP = ; CAPABILITIES = NET_OPER, VPN_OPER; | |
| INT mcmIsdnLapdCntrAction | 1.3.6.1.4.1.335.1.4.24.2.2.1.2 | INTEGER | write-only | NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ Setting this object to reset(1) will zero \ the values of a specific row of counters in \ the ISDN LAPD table defined in the MIB \ file rfc2127.mib.; HELP = When set to reset(1), a row containing \ the following counter objects are reset: \ isdnLapdPeerSabme \ isdnLapdRecvdFrmr; CAPABILITIES = ; |
| mcmIsdnLapdCntrEntry | 1.3.6.1.4.1.335.1.4.24.2.2.1 | not-accessible | NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ An entry in the ISDN LAPD counter \ reset table.; HELP = ; CAPABILITIES = ; | |
| INT mcmIsdnLapdCntrIndex | 1.3.6.1.4.1.335.1.4.24.2.2.1.1 | INTEGER | read-only | NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ The value of this object represents a unique \ identifier used as the index into the ISDN \ LAPD counter reset table. This index specifies \ the particular row of counter objects to be reset \ (objects defined in the ISDN LAPD table in the \ MIB file rfc2127.mib). This index has the \ identical value as the object ifIndex (defined in \ the IF-MIB).; HELP = ; CAPABILITIES = ; |
| mcmIsdnLapdCntrTable | 1.3.6.1.4.1.335.1.4.24.2.2 | not-accessible | NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ The ISDN LAPD counter reset table.; HELP = ; CAPABILITIES = NET_OPER, VPN_OPER; | |
| mcmIsdnLapdEntry | 1.3.6.1.4.1.335.1.4.24.1.3.1 | not-accessible | NAME = ; DESC = An entry in the LAPD Table. (Extensions to LAPD \ table in RFC2127 MIB.) (Operational); HELP = ; CAPABILITIES = ; | |
| INT mcmIsdnLapdn200 | 1.3.6.1.4.1.335.1.4.24.1.3.1.10 | INTEGER | read-only | NAME = ; DESC = The value of this object specifies the Retry \ Counter N200. This is the maximum number \ of retransmissions of a frame. (Operational); HELP = ; CAPABILITIES = ; |
| INT mcmIsdnLapdn202 | 1.3.6.1.4.1.335.1.4.24.1.3.1.11 | INTEGER | read-only | NAME = ; DESC = The value of this object specifies the Retry \ Counter N202. This is the maximum number \ of transmissions of a TEI identity request \ message. (Operational); HELP = ; CAPABILITIES = ; |
| INT mcmIsdnLapdnm20 | 1.3.6.1.4.1.335.1.4.24.1.3.1.12 | INTEGER | read-only | NAME = ; DESC = The value of this object specifies the Retry \ Counter NM20 (for TEI management). \ (Operational); HELP = ; CAPABILITIES = ; |
| INT mcmIsdnLapdRxfrmsiz | 1.3.6.1.4.1.335.1.4.24.1.3.1.4 | INTEGER | read-only | NAME = ; DESC = The value of this object specifies the maximum \ receive frame size (in bytes). (Operational); HELP = ; CAPABILITIES = ; |
| INT mcmIsdnLapdRxwinsiz | 1.3.6.1.4.1.335.1.4.24.1.3.1.2 | INTEGER | read-only | NAME = ; DESC = The value of this object specifies the receive \ window size (maximum number of outstanding \ unacknowledged information frames. (Operational); HELP = Default values: 7 for PRI, 1 for BRI with SAPI=0, \ 3 for BRI with other SAPIs.; CAPABILITIES = ; |
| mcmIsdnLapdTable | 1.3.6.1.4.1.335.1.4.24.1.3 | not-accessible | NAME = ; DESC = Table containing configuration and statistics \ information for all LAPD (D channel Data Link) \ interfaces on this managed device. \ Only statistical information which is not already being \ counted in the ifTable is being defined in this table. \ This table is an extension to the LAPD table resident in \ the RFC2127 MIB. (Operational) HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ; | |
| INT mcmIsdnLapdTimert200 | 1.3.6.1.4.1.335.1.4.24.1.3.1.5 | INTEGER | read-only | NAME = ; DESC = The value of this object specifies the timer \ T200 value (in milliseconds). T200 is the time \ to wait for an acknowledgment to a frame \ before initiating recovery. (Operational); HELP = ; CAPABILITIES = ; |
| INT mcmIsdnLapdTimert201 | 1.3.6.1.4.1.335.1.4.24.1.3.1.6 | INTEGER | read-only | NAME = ; DESC = The value of this object specifies the timer \ T201 value (in milliseconds). T201 is the minimum \ time between the transmission of the TEI identity \ check messages. (Operational); HELP = ; CAPABILITIES = ; |
| INT mcmIsdnLapdTimert202 | 1.3.6.1.4.1.335.1.4.24.1.3.1.7 | INTEGER | read-only | NAME = ; DESC = The value of this object specifies the timer \ T202 value (in milliseconds). T201 is the minimum \ time between the transmission of the TEI identity \ request messages. (Operational); HELP = ; CAPABILITIES = ; |
| INT mcmIsdnLapdTimert203 | 1.3.6.1.4.1.335.1.4.24.1.3.1.8 | INTEGER | read-only | NAME = ; DESC = The value of this object specifies the timer \ T203 value (in milliseconds). T203 is the maximum \ time allowed without frames being exchanged. \ (Operational); HELP = ; CAPABILITIES = ; |
| INT mcmIsdnLapdTimertm20 | 1.3.6.1.4.1.335.1.4.24.1.3.1.9 | INTEGER | read-only | NAME = ; DESC = The value of this object specifies the timer \ TM20 value (in milliseconds) for TEI management. \ (Operational); HELP = ; CAPABILITIES = ; |
| INT mcmIsdnLapdTxfrmsiz | 1.3.6.1.4.1.335.1.4.24.1.3.1.3 | INTEGER | read-only | NAME = ; DESC = The value of this object specifies the maximum \ transmit frame size (in bytes). (Operational); HELP = ; CAPABILITIES = ; |
| INT mcmIsdnLapdTxwinsiz | 1.3.6.1.4.1.335.1.4.24.1.3.1.1 | INTEGER | read-only | NAME = ; DESC = The value of this object specifies the transmit \ window size (maximum number of outstanding \ unacknowledged information frames. (Operational); HELP = Default values: 7 for PRI, 1 for BRI with SAPI=0, \ 3 for BRI with other SAPIs.; CAPABILITIES = ; |
| INT mcmIsdnSigStatsCntrAction | 1.3.6.1.4.1.335.1.4.24.2.1.1.2 | INTEGER | write-only | NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ Setting this object to reset(1) will zero \ the values of a specific row of counters in \ the ISDN Signaling Statistics table defined \ in the MIB file rfc2127.mib.; HELP = When set to reset(1), a row containing \ the following counter objects are reset: \ isdnSigStatsInCalls \ isdnSigStatsInConnected \ isdnSigStatsOutCalls \ isdnSigStatsOutConnected \ isdnSigStatsChargedUnits; CAPABILITIES = ; |
| mcmIsdnSigStatsCntrEntry | 1.3.6.1.4.1.335.1.4.24.2.1.1 | not-accessible | NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ An entry in the ISDN Signaling Statistics counter \ reset table.; HELP = ; CAPABILITIES = ; | |
| INT mcmIsdnSigStatsCntrIndex | 1.3.6.1.4.1.335.1.4.24.2.1.1.1 | INTEGER | read-only | NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ The value of this object represents a unique \ identifier used as the index into the \ ISDN Signaling Statistics counter reset table. \ This index specifies the particular row of counter \ objects to be reset (objects defined in the ISDN \ Signaling Statistics table in the MIB file rfc2127.mib). \ This index has the identical value as the object \ isdnSignalingIndex (also defined in the MIB \ file rfc2127.mib).; HELP = ; CAPABILITIES = ; |
| mcmIsdnSigStatsCntrTable | 1.3.6.1.4.1.335.1.4.24.2.1 | not-accessible | NAME = ; DESC = This table was obsoleted as of release \ 3.0; and is included here only to support \ backwards compatibility for software \ versions prior to release 3.0. \ The ISDN Signaling Statistics counter reset table.; HELP = ; CAPABILITIES = NET_OPER, VPN_OPER; | |
| micom_isdn | 1.3.6.1.4.1.335.1.4.24 | |||
| INT nvmCallHistoryTableMaxLength | 1.3.6.1.4.1.335.1.4.24.1.10 | INTEGER | read-write | NAME = ; DESC = The upper limit on the number of entries that the \ callHistoryTable may contain. A value of 0 \ will prevent any history from being retained. When \ this table is full, the oldest entry will be deleted \ and the new one will be created. (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_DISP ; |
| INT nvmDialCtlAcceptMode | 1.3.6.1.4.1.335.1.4.24.1.7.1 | INTEGER | read-write | NAME = ; DESC = The security level for acceptance of incoming calls. \ acceptNone(1) - incoming calls will not be accepted. \ acceptAll(2) - incoming calls will be accepted, even. \ if there is no matching entry in the nvmDialCtlPeerCfgTable. \ acceptKnown(3) - incoming calls will be accepted only \ if there is a matching entry in the nvmDialCtlPeerCfgTable. \ (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_DISP ; |
| nvmDialCtlConfiguration | 1.3.6.1.4.1.335.1.4.24.1.7 | |||
| INT nvmDialCtlPeerCfgBchannel | 1.3.6.1.4.1.335.1.4.24.1.9.1.2 | INTEGER | read-write | NAME = ; DESC = The value of this object specifies the B channel to be used \ for leased lines. (Configuration); HELP = Note: 0 = 'any'. This managed object is not part of the \ original Dial Control MIB (RFC2128). This proprietary \ object was added for ICM purposes.; CAPABILITIES = ; |
| INT nvmDialCtlPeerCfgCallRetries | 1.3.6.1.4.1.335.1.4.24.1.9.1.10 | INTEGER | read-write | NAME = ; DESC = The number of calls to a non-responding address \ that may be made. A retry count of zero means \ there is no bound. The intent is to bound \ the number of successive calls to an address \ which is inaccessible, or which refuses those calls. \ Some countries regulate the number of call retries \ to a given peer that can be made. (Configuration); HELP = ; CAPABILITIES = ; |
| STR nvmDialCtlPeerCfgClosedUserGroup | 1.3.6.1.4.1.335.1.4.24.1.9.1.6 | DisplayString | read-write | NAME = ; DESC = Closed User Group at which the peer will be called. \ If the Closed User Group is undefined for the given media \ or unused, this is a zero length string. (Configuration); HELP = ; CAPABILITIES = ; |
| nvmDialCtlPeerCfgEntry | 1.3.6.1.4.1.335.1.4.24.1.9.1 | not-accessible | NAME = ; DESC = Configuration data for a single Peer. This entry is \ effectively permanent, and contains information \ to identify the peer, how to connect to the peer, \ how to identify the peer and its permissions. \ The value of nvmDialCtlPeerCfgOriginateAddress must be \ specified before a new row in this table can become \ active(1). Any writeable parameters in an existing entry \ can be modified while the entry is active. The modification \ will take effect when the peer in question will be \ called the next time. \ An entry in this table can only be created if the \ associated ifEntry already exists. (Configuration); HELP = ; CAPABILITIES = ; | |
| INT nvmDialCtlPeerCfgFailureDelay | 1.3.6.1.4.1.335.1.4.24.1.9.1.12 | INTEGER | read-write | NAME = ; DESC = The time in seconds after which call attempts are \ to be placed again after a peer has been noticed \ to be unreachable, i.e. after nvmDialCtlPeerCfgCallRetries \ unsuccessful call attempts. \ A value of zero means that a peer will not be called \ again after nvmDialCtlPeerCfgCallRetries unsuccessful call \ attempts. (Configuration); HELP = This value is the time to wait with another call \ retry after nvmDialCtlPeerCfgCallRetries unsuccessful \ calls. ICM uses the default value of zero, which means \ that a peer will not be called again after \ nvmDialCtlPeerCfgCallRetriesattempts. The whole call \ retry logic will be implemented.; CAPABILITIES = ; |
| INT nvmDialCtlPeerCfgId | 1.3.6.1.4.1.335.1.4.24.1.9.1.1 | INTEGER | read-only | NAME = ; DESC = This object identifies a single peer. There may \ be several entries in this table for one peer, \ defining different ways of reaching this peer. \ Thus, there may be several entries in this table \ with the same value of nvmDialCtlPeerCfgId. \ Multiple entries for one peer may be used to support \ multilink as well as backup lines. \ A single peer will be identified by a unique value \ of this object. Several entries for one peer MUST \ have the same value of nvmDialCtlPeerCfgId, but different \ ifEntries and thus different values of ifIndex. \ (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmDialCtlPeerCfgInfoType | 1.3.6.1.4.1.335.1.4.24.1.9.1.8 | INTEGER | read-write | NAME = ; DESC = The Information Transfer Capability to be used when \ calling this peer. \ speech(2) refers to a non-data connection, whereas \ audio31(6) and audio7(7) refer to data mode \ connections. (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmDialCtlPeerCfgLowerIf | 1.3.6.1.4.1.335.1.4.24.1.9.1.3 | INTEGER | read-write | NAME = ; DESC = ifIndex value of an interface the peer will have to be \ called on. For example, on an ISDN interface, this can be \ the ifIndex value of a D channel or the ifIndex value of a \ B channel, whatever is appropriate for a given peer. \ As an example, for Basic Rate leased lines it will be \ necessary to specify a B channel ifIndex, while for \ semi-permanent connections the D channel ifIndex has \ to be specified. \ If the interface can be dynamically assigned, this object \ has a value of zero. (Configuration); HELP = The LowerIf is the ifIndex value of a D channel index \ (primary or backup port for a semi-permanent connection), \ or the ifIndex value of a B channel for a leased line.; CAPABILITIES = ; |
| STR nvmDialCtlPeerCfgOriginateAddress | 1.3.6.1.4.1.335.1.4.24.1.9.1.4 | DisplayString | read-write | NAME = ; DESC = Call Address at which the peer will be called. \ Think of this as the set of characters following 'ATDT ' \ or the 'phone number' included in a D channel call request. \ The structure of this information will be switch type \ specific. If there is no address information required \ for reaching the peer, i.e., for leased lines, \ this object will be a zero length string. (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmDialCtlPeerCfgPermission | 1.3.6.1.4.1.335.1.4.24.1.9.1.9 | INTEGER | read-write | NAME = ; DESC = Applicable permissions. callback(4) either rejects the \ call and then calls back, or uses the 'Reverse charging' \ information element if it is available. \ Note that callback(4) is supposed to control charging, not \ security, and applies to callback prior to accepting a \ call. Callback for security reasons can be handled using \ PPP callback. (Configuration); HELP = Access device ISDN does not support 'callback(4)'. The value \ 'originate' is for outgoing calls. The value 'answer' is \ for incoming calls.; CAPABILITIES = ; |
| INT nvmDialCtlPeerCfgRetryDelay | 1.3.6.1.4.1.335.1.4.24.1.9.1.11 | INTEGER | read-write | NAME = ; DESC = The time in seconds between call retries if a peer \ cannot be reached. \ A value of zero means that call retries may be done \ without any delay. (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmDialCtlPeerCfgSpeed | 1.3.6.1.4.1.335.1.4.24.1.9.1.7 | INTEGER | read-write | NAME = ; DESC = The desired information transfer speed in bits/second \ when calling this peer. \ The detailed media specific information, e.g. information \ type and information transfer rate for ISDN circuits, \ has to be extracted from this object. \ If the transfer speed to be used is unknown or the default \ speed for this type of interfaces, the value of this object \ may be zero. (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmDialCtlPeerCfgStatus | 1.3.6.1.4.1.335.1.4.24.1.9.1.14 | INTEGER | read-write | NAME = ; DESC = For software releases prior to 3.0 \ this object only supported enumerations of \ add and delete with an access of write-only. \ This object is used to create and delete rows in the \ nvmDialCtlPeerCfgTable. Upon creation of a row, the \ the row status is internally set to 'active'. \ (Configuration); HELP = ; CAPABILITIES = ; |
| STR nvmDialCtlPeerCfgSubAddress | 1.3.6.1.4.1.335.1.4.24.1.9.1.5 | DisplayString | read-write | NAME = ; DESC = Subaddress at which the peer will be called. \ If the subaddress is undefined for the given media or \ unused, this is a zero length string. (Configuration); HELP = ; CAPABILITIES = ; |
| nvmDialCtlPeerCfgTable | 1.3.6.1.4.1.335.1.4.24.1.9 | not-accessible | NAME = ; DESC = The list of peers from which the managed device \ will accept calls or to which it will place them. \ (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_DISP ; | |
| INT nvmDialCtlPeerCfgTrapEnable | 1.3.6.1.4.1.335.1.4.24.1.9.1.13 | INTEGER | read-write | NAME = ; DESC = This object indicates whether dialCtlPeerCallInformation \ and dialCtlPeerCallSetup traps should be generated for \ this peer. (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmDialCtlTrapEnable | 1.3.6.1.4.1.335.1.4.24.1.7.2 | INTEGER | read-write | NAME = ; DESC = This object indicates whether nvmDialCtlPeerCallInformation \ and nvmDialCtlPeerCallSetup traps should be generated for \ all peers. If the value of this object is enabled(1), \ traps will be generated for all peers. If the value \ of this object is disabled(2), traps will be generated \ only for peers having nvmDialCtlPeerCfgTrapEnable set \ to enabled(1). (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_DISP ; |
| nvmIsdnBasicRateEntry | 1.3.6.1.4.1.335.1.4.24.1.1.1 | not-accessible | NAME = ; DESC = An entry in the ISDN Basic Rate Table. \ (Configuration); HELP = ; CAPABILITIES = ; | |
| INT nvmIsdnBasicRateLineTopology | 1.3.6.1.4.1.335.1.4.24.1.1.1.1 | INTEGER | read-write | NAME = ; DESC = The line topology to be used for this interface. \ Note that setting nvmIsdnBasicRateIfType to isdns(75) \ does not necessarily mean a line topology of \ point-to-multipoint. (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmIsdnBasicRateSignalMode | 1.3.6.1.4.1.335.1.4.24.1.1.1.2 | INTEGER | read-write | NAME = ; DESC = The signaling channel operational mode for this \ interface. If dialup(1), there is a signaling channel \ on this interface and the corresponding operational \ object, isdnBasicRateSignalMode (see rfc2127.mib), \ will be active(1). If leased(2), a signaling channel \ is not available and the corresponding operational \ object, isdnBasicRateSignalMode, will be inactive(2). \ (Configuration); HELP = ; CAPABILITIES = ; |
| nvmIsdnBasicRateTable | 1.3.6.1.4.1.335.1.4.24.1.1 | not-accessible | NAME = ; DESC = Table containing configuration and operational \ parameters for all physical Basic Rate interfaces \ on this managed device. (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ; | |
| nvmIsdnDirectoryEntry | 1.3.6.1.4.1.335.1.4.24.1.6.1 | not-accessible | NAME = ; DESC = An entry in the Directory Number Table. All objects \ in an entry must be set for a new row to become active. \ (Configuration); HELP = ; CAPABILITIES = ; | |
| INT nvmIsdnDirectoryIndex | 1.3.6.1.4.1.335.1.4.24.1.6.1.1 | INTEGER | read-only | NAME = ; DESC = The index value which uniquely identifies an entry \ in the nvmIsdnDirectoryTable. (Configuration); HELP = ; CAPABILITIES = ; |
| STR nvmIsdnDirectoryNumber | 1.3.6.1.4.1.335.1.4.24.1.6.1.2 | DisplayString | read-write | NAME = ; DESC = A Directory Number. Directory Numbers are used \ to identify incoming calls on the signaling \ channel given in nvmIsdnDirectorySigIndex. \ The format of this information largely depends on the \ type of switch or PBX the device is connected to. \ Therefore, the detailed format of this information is \ not specified and is implementation dependent. \ If possible, the agent should implement this information \ using the E.164 number format. In this case, the number \ must start with '+'. Otherwise, IA5 number digits must \ be used. (Configuration); HELP = This ICM variable contains the remote address for which \ incoming calls are handled.; CAPABILITIES = ; |
| INT nvmIsdnDirectorySigIndex | 1.3.6.1.4.1.335.1.4.24.1.6.1.3 | INTEGER | read-write | NAME = ; DESC = An index pointing to an ISDN signaling channel. \ Incoming calls are accepted on this \ signaling channel if the nvmIsdnDirectoryNumber is \ presented as Called Number in the SETUP message. \ (Configuration); HELP = This is an index to a link in the dialCtlPeerCfg table \ (and not an index to a signaling channel). The ICM \ changes the meaning of this managed object in order \ to be able to extract the link for which the directory \ number is specified.; CAPABILITIES = ; |
| INT nvmIsdnDirectoryStatus | 1.3.6.1.4.1.335.1.4.24.1.6.1.4 | INTEGER | read-write | NAME = ; DESC = For software releases prior to 3.0 \ this object only supported enumerations of \ add and delete with an access of write-only. \ This object is used to create and delete rows in the \ nvmIsdnDirectoryTable. Upon creation of a row, the \ the row status is internally set to 'active'. \ (Configuration); HELP = ; CAPABILITIES = ; |
| nvmIsdnDirectoryTable | 1.3.6.1.4.1.335.1.4.24.1.6 | not-accessible | NAME = ; DESC = Table containing Directory Numbers. (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ; | |
| nvmIsdnEndpointEntry | 1.3.6.1.4.1.335.1.4.24.1.5.1 | not-accessible | NAME = ; DESC = An entry in the Terminal Endpoint Table. The value \ of nvmIsdnEndpointIfType must be supplied for a row \ in this table to become active. (Configuration); HELP = ; CAPABILITIES = ; | |
| INT nvmIsdnEndpointIndex | 1.3.6.1.4.1.335.1.4.24.1.5.1.1 | INTEGER | read-only | NAME = ; DESC = The index value which uniquely identifies an entry \ in the nvmIsdnEndpointTable. (Configuration); HELP = ; CAPABILITIES = ; |
| STR nvmIsdnEndpointSpid | 1.3.6.1.4.1.335.1.4.24.1.5.1.4 | DisplayString | read-write | NAME = ; DESC = The Service profile IDentifier (SPID) information \ for this Terminal Endpoint. \ The SPID is composed of 9-20 numeric characters. \ This information has to be defined in addition to \ the local number for some switch protocol types, \ e.g. Bellcore NI-1 and NI-2. \ If this object is not required, it is a \ zero length string. (Configuration); HELP = ; CAPABILITIES = ; |
| nvmIsdnEndpointTable | 1.3.6.1.4.1.335.1.4.24.1.5 | not-accessible | NAME = ; DESC = Table containing configuration for Terminal \ Endpoints. (Configuration); HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ; | |
| INT nvmIsdnEndpointTeiType | 1.3.6.1.4.1.335.1.4.24.1.5.1.2 | INTEGER | read-write | NAME = ; DESC = The type of TEI (Terminal Endpoint Identifier) \ used for this Terminal Endpoint. In case of dynamic(1), \ the TEI value is selected by the switch. In \ case of static(2), a valid TEI value has to be \ entered in the nvmIsdnEndpointTeiValue object. \ The default value for this object depends on the \ interface type as well as the Terminal Endpoint type. \ On Primary Rate interfaces the default value is \ static(2). On Basic Rate interfaces the default value \ is dynamic(1) for isdn(63) Terminal Endpoints and \ static(2) for x25ple(40) Terminal Endpoints. \ (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmIsdnEndpointTeiValue | 1.3.6.1.4.1.335.1.4.24.1.5.1.3 | INTEGER | read-write | NAME = ; DESC = The TEI (Terminal Endpoint Identifier) value \ for this Terminal Endpoint. If nvmIsdnEndpointTeiType \ is set to static(2), valid numbers are 0..63, \ while otherwise the value is set internally. \ The default value of this object is 0 for static \ TEI assignment. \ The default value for dynamic TEI assignment is also \ 0 as long as no TEI has been assigned. After TEI \ assignment, the assigned TEI value is returned. \ (Configuration); HELP = ; CAPABILITIES = ; |
| nvmIsdnLapdEntry | 1.3.6.1.4.1.335.1.4.24.1.4.1 | not-accessible | NAME = ; DESC = An entry in the LAPD Table. (Extensions to LAPD \ table in RFC2127 MIB.) (Configuration); HELP = ; CAPABILITIES = ; | |
| INT nvmIsdnLapdn200 | 1.3.6.1.4.1.335.1.4.24.1.4.1.10 | INTEGER | read-write | NAME = ; DESC = The value of this object specifies the Retry \ Counter N200. This is the maximum number \ of retransmissions of a frame. (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmIsdnLapdn202 | 1.3.6.1.4.1.335.1.4.24.1.4.1.11 | INTEGER | read-write | NAME = ; DESC = The value of this object specifies the Retry \ Counter N202. This is the maximum number \ of transmissions of a TEI identity request \ message. (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmIsdnLapdnm20 | 1.3.6.1.4.1.335.1.4.24.1.4.1.12 | INTEGER | read-write | NAME = ; DESC = The value of this object specifies the Retry \ Counter NM20 (for TEI management). \ (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmIsdnLapdRxfrmsiz | 1.3.6.1.4.1.335.1.4.24.1.4.1.4 | INTEGER | read-write | NAME = ; DESC = The value of this object specifies the maximum \ receive frame size (in bytes). (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmIsdnLapdRxwinsiz | 1.3.6.1.4.1.335.1.4.24.1.4.1.2 | INTEGER | read-write | NAME = ; DESC = The value of this object specifies the receive \ window size (maximum number of outstanding \ unacknowledged information frames. (Configuration); HELP = Default values: 7 for PRI, 1 for BRI with SAPI=0, \ 3 for BRI with other SAPIs.; CAPABILITIES = ; |
| nvmIsdnLapdTable | 1.3.6.1.4.1.335.1.4.24.1.4 | not-accessible | NAME = ; DESC = Table containing configuration and statistics \ information for all LAPD (D channel Data Link) \ interfaces on this managed device. \ Only statistical information which is not already being \ counted in the ifTable is being defined in this table. \ This table is an extension to the LAPD table resident in \ the RFC2127 MIB. (Configuration) HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ; | |
| INT nvmIsdnLapdTimert200 | 1.3.6.1.4.1.335.1.4.24.1.4.1.5 | INTEGER | read-write | NAME = ; DESC = The value of this object specifies the timer \ T200 value (in milliseconds). T200 is the time \ to wait for an acknowledgment to a frame \ before initiating recovery. (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmIsdnLapdTimert201 | 1.3.6.1.4.1.335.1.4.24.1.4.1.6 | INTEGER | read-write | NAME = ; DESC = The value of this object specifies the timer \ T201 value (in milliseconds). T201 is the minimum \ time between the transmission of the TEI identity \ check messages. (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmIsdnLapdTimert202 | 1.3.6.1.4.1.335.1.4.24.1.4.1.7 | INTEGER | read-write | NAME = ; DESC = The value of this object specifies the timer \ T202 value (in milliseconds). T201 is the minimum \ time between the transmission of the TEI identity \ request messages. (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmIsdnLapdTimert203 | 1.3.6.1.4.1.335.1.4.24.1.4.1.8 | INTEGER | read-write | NAME = ; DESC = The value of this object specifies the timer \ T203 value (in milliseconds). T203 is the maximum \ time allowed without frames being exchanged. \ (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmIsdnLapdTimertm20 | 1.3.6.1.4.1.335.1.4.24.1.4.1.9 | INTEGER | read-write | NAME = ; DESC = The value of this object specifies the timer \ TM20 value (in milliseconds) for TEI management. \ (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmIsdnLapdTxfrmsiz | 1.3.6.1.4.1.335.1.4.24.1.4.1.3 | INTEGER | read-write | NAME = ; DESC = The value of this object specifies the maximum \ transmit frame size (in bytes). (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmIsdnLapdTxwinsiz | 1.3.6.1.4.1.335.1.4.24.1.4.1.1 | INTEGER | read-write | NAME = ; DESC = The value of this object specifies the transmit \ window size (maximum number of outstanding \ unacknowledged information frames. (Configuration); HELP = Default values: 7 for PRI, 1 for BRI with SAPI=0, \ 3 for BRI with other SAPIs.; CAPABILITIES = ; |
| STR nvmIsdnSignalingCallingAddress | 1.3.6.1.4.1.335.1.4.24.1.2.1.3 | DisplayString | read-write | NAME = ; DESC = The ISDN Address to be assigned to this signaling \ channel. More specifically, this is the 'Calling Address \ information element' as being passed to the switch \ in outgoing call setup messages. \ It can be an EAZ (1TR6), a calling number (DSS1, \ ETSI)or any other number necessary to identify a \ signaling interface. If there is no such number defined \ or required, this is a zero length string. It is represented \ in DisplayString form. \ Incoming calls can also be identified by this number. \ If the Directory Number, i.e. the Called Number in \ incoming calls, is different to this number, the \ isdnDirectoryTable has to be used to specify all \ possible Directory Numbers. \ The format of this information largely depends on the \ type of switch or PBX the device is connected to. Therefore, \ the detailed format of this information is not \ specified and is implementation dependent. \ If possible, the agent should implement this information \ using the E.164 number format. In this case, the number \ must start with '+'. Otherwise, IA5 number digits must \ be used. (Configuration) ; HELP = ; CAPABILITIES = ; |
| nvmIsdnSignalingEntry | 1.3.6.1.4.1.335.1.4.24.1.2.1 | not-accessible | NAME = ; DESC = An entry in the ISDN Signaling Table. To create a \ new entry, only nvmIsdnSignalingProtocol needs to be \ specified before nvmIsdnSignalingStatus can become \ active(1). (Configuration) ; HELP = ; CAPABILITIES = ; | |
| INT nvmIsdnSignalingIndex | 1.3.6.1.4.1.335.1.4.24.1.2.1.1 | INTEGER | read-only | NAME = ; DESC = The index value which uniquely identifies an entry \ in the nvmIsdnSignalingTable. (Configuration); HELP = This managed object corresponds to the port index used \ in the ICM ('primary' and 'backup' ports supported).; CAPABILITIES = ; |
| INT nvmIsdnSignalingInfoTrapEnable | 1.3.6.1.4.1.335.1.4.24.1.2.1.5 | INTEGER | read-write | NAME = ; DESC = Indicates whether isdnMibCallInformation traps \ should be generated for calls on this signaling \ channel. (Configuration); HELP = ; CAPABILITIES = ; |
| INT nvmIsdnSignalingProtocol | 1.3.6.1.4.1.335.1.4.24.1.2.1.2 | INTEGER | read-write | NAME = ; DESC = The particular protocol type supported by the \ switch providing access to the ISDN network \ to which this signaling channel is connected. (Configuration); HELP = Enumerations supported by access device are 2, 3, 6, 7, \ 9, 12, 13, 17, and 19.; CAPABILITIES = ; |
| STR nvmIsdnSignalingSubAddress | 1.3.6.1.4.1.335.1.4.24.1.2.1.4 | DisplayString | read-write | NAME = ; DESC = Supplementary information to the ISDN address assigned \ to this signaling channel. Usually, this is the \ subaddress as defined in Q.931. \ If there is no such number defined or required, this is \ a zero length string. \ The subaddress is used for incoming calls as well as \ for outgoing calls. \ The subaddress is an user supplied string of up to 20 \ IA5 characters and is transmitted transparently through \ the network. (Configuration) ; HELP = ; CAPABILITIES = ; |
| nvmIsdnSignalingTable | 1.3.6.1.4.1.335.1.4.24.1.2 | not-accessible | NAME = ; DESC = ISDN signaling table containing configuration and \ operational parameters for all ISDN signaling \ channels on this managed device. (Configuration) ; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG ; |
RFC description
Manages MICOM ISDN access device configuration including basic rate interfaces, signaling protocols, and dial control.
Start monitoring Micom WAN access router/multiplexer (ISDN BRI/PRI) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.