All MIBs › MICOM-CSU-MIB
Category: WAN
Description: Monitors CSU/DSU line status and loopback settings on Micom WAN equipment.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is MICOM-CSU-MIB?
MICOM-CSU-MIB is a MICOM Communications (network/VPN configuration hardware) proprietary MIB configuring T1/E1 CSU (Channel Service Unit) line parameters. Its per-interface configuration table records line type/speed/build-out, TX idle code, TX/RX clock source, DS0 basic rate, local/remote/framer/payload loopback controls, trap enable, frame format, TX/RX zero-code and B7-zero suppression, transmit loop-up/loop-down actions, TX/RX HDB3 and CRC4 settings, and DS0 connection mapping, alongside a companion general CSU-configuration table. As a configuration MIB it lets an administrator confirm T1/E1 line framing/clocking settings and trigger a loopback test on a MICOM CSU. It is deployed on MICOM Communications T1/E1 CSU equipment. Engineers can download the MICOM-CSU-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in MICOM-CSU-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- MICOM Communications T1/E1 CSU equipment
Monitoring Examples
An administrator sets mcmT1E1CsuCfgLocalLoopback to trigger a loopback test and confirm mcmT1E1CsuCfgLineType matches the carrier's line settings on a MICOM CSU.
What Can Be Monitored
- T1/E1 line configuration and loopback test control
This MIB depends on
Related MIBs
Imported Objects
From MICOM-OSCAR-MIB
| micom-oscar |
From MICOM-SYS-MIB
| mcmSysAsciiTimeOfDay | OBJECT-TYPE |
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From SNMPv2-TC
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| csu_configuration | 1.3.6.1.4.1.335.1.4.29.1 | |||
| csu_status | 1.3.6.1.4.1.335.1.4.29.2 | |||
| INT mcmCsuCfgClockingSource | 1.3.6.1.4.1.335.1.4.29.1.2.1.3 | INTEGER | read-write | NAME = ; DESC = The value of this object selects the 56K CSU \ clocking source.; HELP = ; CAPABILITIES = ; |
| INT mcmCsuCfgCSULoopback | 1.3.6.1.4.1.335.1.4.29.1.2.1.9 | INTEGER | read-write | NAME = ; DESC = This object selects the 56K CSU to force the CSU \ to be in a loopback mode.; HELP = ; CAPABILITIES = ; |
| mcmCsuCfgEntry | 1.3.6.1.4.1.335.1.4.29.1.2.1 | not-accessible | NAME = ; DESC = An entry in the 56K CSU Configuration \ table.); HELP = ; CAPABILITIES = ; | |
| INT mcmCsuCfgFilterForceEnable | 1.3.6.1.4.1.335.1.4.29.1.2.1.10 | INTEGER | read-write | NAME = ; DESC = This object selects the 56K CSU to have \ filter forcing enabled or not.; HELP = ; CAPABILITIES = ; |
| INT mcmCsuCfgFilterForcingCntl | 1.3.6.1.4.1.335.1.4.29.1.2.1.11 | INTEGER | read-write | NAME = ; DESC = This object selects the 56K CSU filter \ gain if filter force is enabled.; HELP = ; CAPABILITIES = ; |
| INT mcmCsuCfgifIndex | 1.3.6.1.4.1.335.1.4.29.1.2.1.1 | INTEGER | read-only | NAME = ; DESC = The 56k Csu Cfg interface index \ value of the specifc entry.; HELP = ; CAPABILITIES = ; |
| INT mcmCsuCfgOperatingMode | 1.3.6.1.4.1.335.1.4.29.1.2.1.2 | INTEGER | read-write | NAME = ; DESC = The value of this object selects the 56K CSU \ operating mode.; HELP = ; CAPABILITIES = ; |
| mcmCsuCfgTable | 1.3.6.1.4.1.335.1.4.29.1.2 | not-accessible | NAME = ; DESC = The 56K CSU Configuration table.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG; | |
| INT mcmCsuCfgTxControlModeIdle | 1.3.6.1.4.1.335.1.4.29.1.2.1.6 | INTEGER | read-write | NAME = ; DESC = This object selects transmission of the 56K CSU \ Control Mode Idle sequence.; HELP = ; CAPABILITIES = ; |
| INT mcmCsuCfgTxIdle | 1.3.6.1.4.1.335.1.4.29.1.2.1.8 | INTEGER | read-write | NAME = ; DESC = This object selects transmission of the 56K CSU \ All Marks (or 1s) of the Data Mode Idle sequence \ for all the modes.; HELP = ; CAPABILITIES = ; |
| INT mcmCsuCfgTxOutOfFrame | 1.3.6.1.4.1.335.1.4.29.1.2.1.4 | INTEGER | read-write | NAME = ; DESC = This object selects transmission of the 56K CSU \ Out Of Frame sequence for DDS-PRI mode, or \ transmission of Multiplexer Out Of Sync \ sequence for DDS-SC mode.; HELP = ; CAPABILITIES = ; |
| INT mcmCsuCfgTxOutOfService | 1.3.6.1.4.1.335.1.4.29.1.2.1.5 | INTEGER | read-write | NAME = ; DESC = This object selects transmission of the 56K CSU \ Out Of Service sequence for DDS-PRI mode, or \ transmission of Abnormal Station Code \ sequence for DDS-SC mode.; HELP = ; CAPABILITIES = ; |
| INT mcmCsuCfgZeroSuppressDisable | 1.3.6.1.4.1.335.1.4.29.1.2.1.7 | INTEGER | read-write | NAME = ; DESC = This object selects the 56K CSU disable \ transmit Zero Suppression for DDS-PRI mode, \ or transmission of all zeros for DDS-SC mode.; HELP = ; CAPABILITIES = ; |
| mcmCsuStatusEntry | 1.3.6.1.4.1.335.1.4.29.2.4.1 | not-accessible | NAME = ; DESC = An entry in the 56K CSU Status \ and Statistics table.; HELP = ; CAPABILITIES = ; | |
| INT mcmCsuStatusFAWSync | 1.3.6.1.4.1.335.1.4.29.2.4.1.4 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the 56K \ CSU DDS FAW Sync in DDS-SC or CC-64K.; HELP = ; CAPABILITIES = ; |
| INT mcmCsuStatusifIndex | 1.3.6.1.4.1.335.1.4.29.2.4.1.1 | INTEGER | read-only | NAME = ; DESC = The 56k CSU Status interface index \ value of the specifc entry.; HELP = ; CAPABILITIES = ; |
| INT mcmCsuStatusInsertLossLineLength | 1.3.6.1.4.1.335.1.4.29.2.4.1.6 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the 56K \ CSU receiver Insertion loss (iL) in db, and \ Line Length (LL) in kilometers.; HELP = ; CAPABILITIES = ; |
| INT mcmCsuStatusInvalidBPVcounts | 1.3.6.1.4.1.335.1.4.29.2.4.1.8 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the 56K \ CSU invalid BPV (Bipolar Violation) count. \ Note that this is an 8-bit counter.; HELP = ; CAPABILITIES = ; |
| INT mcmCsuStatusLineStatus | 1.3.6.1.4.1.335.1.4.29.2.4.1.2 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the 56K \ CSU line status.; HELP = ; CAPABILITIES = ; |
| INT mcmCsuStatusLoopPresent | 1.3.6.1.4.1.335.1.4.29.2.4.1.5 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates if the 56K \ CSU loop is currently present.; HELP = ; CAPABILITIES = ; |
| INT mcmCsuStatusRxLossOfSignal | 1.3.6.1.4.1.335.1.4.29.2.4.1.3 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates if the 56K \ CSU receiver has lost signal.; HELP = ; CAPABILITIES = ; |
| INT mcmCsuStatusRxSignalMag | 1.3.6.1.4.1.335.1.4.29.2.4.1.7 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the 56K \ CSU receive signal magnitude expressed as \ the 'receiver slicer level'. This value \ is used in conjunction with the db Insertion \ Loss ('iL' from InsertLossLineLength object) \ to compute the signal magnitude as follows: \ Nyquist frequency loop attn (in db) = \ [(iL)**2 + 20log10(51/RxSignalMag)].; HELP = ; CAPABILITIES = ; |
| mcmCsuStatusTable | 1.3.6.1.4.1.335.1.4.29.2.4 | not-accessible | NAME = ; DESC = The 56K CSU Status and Statistics table.; HELP = ; CAPABILITIES = NET_DISP, VPN_DISP; | |
| NTF mcmE1CsuAISAlarmClear | 1.3.6.1.4.1.335.1.4.29.0.12 | NAME = ; DESC = This trap is generated upon the clearance \ of an E1 CSU AIS Alarm. \ Severity Level: INFORMATIVE.; HELP = ; | ||
| NTF mcmE1CsuAISAlarmSet | 1.3.6.1.4.1.335.1.4.29.0.11 | NAME = ; DESC = This trap is generated upon the occurrence \ of an E1 CSU AIS Alarm. The AIS (alarm indication \ signal) alarm is detected as an all ones condition \ on the E1 line persisting for 100ms or longer. \ This indicates the E1 line is unavailable. \ Severity Level: MINOR.; HELP = ; | ||
| INT mcmE1CsuGenStatusAISAlarm | 1.3.6.1.4.1.335.1.4.29.2.3.1.5 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the \ E1 CSU AIS Alarm status.; HELP = ; CAPABILITIES = ; |
| INT mcmE1CsuGenStatusBpvOrLnCdViolations | 1.3.6.1.4.1.335.1.4.29.2.3.1.12 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the number \ of E1 CSU line code violations. \ Bipolar violation counts if HDB3 disabled, code \ violation counts if HDB3 enabled. \ Note that this is a 16-bit counter.; HELP = ; CAPABILITIES = ; |
| INT mcmE1CsuGenStatusCRC4Errors | 1.3.6.1.4.1.335.1.4.29.2.3.1.14 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the number \ of E1 CSU CRC4 error counts. This object \ is only applicable when CRC4 is enabled. \ Note that this is a 10-bit counter.; HELP = ; CAPABILITIES = ; |
| mcmE1CsuGenStatusEntry | 1.3.6.1.4.1.335.1.4.29.2.3.1 | not-accessible | NAME = ; DESC = An entry in the E1 CSU General \ Status and Statistics table.; HELP = ; CAPABILITIES = ; | |
| INT mcmE1CsuGenStatusFASErrors | 1.3.6.1.4.1.335.1.4.29.2.3.1.13 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the number \ of E1 CSU FAS error counts. FAS error counts \ record word errors in the frame alignment \ signal in timeslot 0. \ Note that this is a 12-bit counter.; HELP = ; CAPABILITIES = ; |
| INT mcmE1CsuGenStatusifIndex | 1.3.6.1.4.1.335.1.4.29.2.3.1.1 | INTEGER | read-only | NAME = ; DESC = The E1 CSU General Status interface \ index value of the specifc entry.; HELP = ; CAPABILITIES = ; |
| INT mcmE1CsuGenStatusLineStatus | 1.3.6.1.4.1.335.1.4.29.2.3.1.2 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the \ E1 CSU line status.; HELP = ; CAPABILITIES = ; |
| INT mcmE1CsuGenStatusRedAlarm | 1.3.6.1.4.1.335.1.4.29.2.3.1.3 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the \ E1 CSU red alarm status. It includes both \ receive carrier loss and receive loss of sync.; HELP = ; CAPABILITIES = ; |
| INT mcmE1CsuGenStatusRemoteAlarm | 1.3.6.1.4.1.335.1.4.29.2.3.1.4 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the \ E1 CSU remote alarm status. It includes both \ receive remote alarm and receive distant MF \ alarm.; HELP = ; CAPABILITIES = ; |
| INT mcmE1CsuGenStatusRxCarrierLoss | 1.3.6.1.4.1.335.1.4.29.2.3.1.6 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the \ E1 CSU receive carrier loss status.; HELP = ; CAPABILITIES = ; |
| INT mcmE1CsuGenStatusRxElasStrEmpty | 1.3.6.1.4.1.335.1.4.29.2.3.1.11 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the E1 \ CSU receive elastic store empty status. This \ indicates that the E1 CSU receive side elastic \ store buffer empties and a frame is repeated.; HELP = ; CAPABILITIES = ; |
| INT mcmE1CsuGenStatusRxElasStrFull | 1.3.6.1.4.1.335.1.4.29.2.3.1.10 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the E1 \ CSU receive elastic store full status. This \ indicates that the E1 CSU receive side elastic \ store buffer fills and a frame is deleted.; HELP = ; CAPABILITIES = ; |
| INT mcmE1CsuGenStatusRxSyncLoss | 1.3.6.1.4.1.335.1.4.29.2.3.1.7 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the E1 \ CSU receive loss of sync status.; HELP = ; CAPABILITIES = ; |
| mcmE1CsuGenStatusTable | 1.3.6.1.4.1.335.1.4.29.2.3 | not-accessible | NAME = ; DESC = The E1 CSU General Status and \ Statistics table.; HELP = ; CAPABILITIES = NET_DISP, VPN_DISP; | |
| INT mcmE1CsuGenStatusTxElasStrEmpty | 1.3.6.1.4.1.335.1.4.29.2.3.1.9 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the E1 \ CSU transmit elastic store empty status. This \ indicates that the E1 CSU transmit side elastic \ store buffer empties and a frame is repeated.; HELP = ; CAPABILITIES = ; |
| INT mcmE1CsuGenStatusTxElasStrFull | 1.3.6.1.4.1.335.1.4.29.2.3.1.8 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the E1 \ CSU transmit elastic store full status. This \ indicates that the E1 CSU transmit side \ elastic store buffer fills and a frame is deleted.; HELP = ; CAPABILITIES = ; |
| NTF mcmE1CsuRedAlarmClear | 1.3.6.1.4.1.335.1.4.29.0.8 | NAME = ; DESC = This trap is generated upon the clearance \ of an E1 CSU Red Alarm. A red alarm is cleared \ when the out-of-frame condition has been absent \ for 100 milliseconds. \ Severity Level : INFORMATIVE.; HELP = ; | ||
| NTF mcmE1CsuRedAlarmSet | 1.3.6.1.4.1.335.1.4.29.0.7 | NAME = ; DESC = This trap is generated upon the occurrence \ of an E1 CSU Red Alarm. A red alarm indicates that \ an out-of-frame condition existed for the last 100 \ milliseconds or longer. \ Severity Level: CRITICAL.; HELP = ; | ||
| NTF mcmE1CsuRemoteAlarmClear | 1.3.6.1.4.1.335.1.4.29.0.10 | NAME = ; DESC = This trap is generated upon the clearance \ of an E1 CSU Remote Alarm. \ Severity Level: INFORMATIVE.; HELP = ; | ||
| NTF mcmE1CsuRemoteAlarmSet | 1.3.6.1.4.1.335.1.4.29.0.9 | NAME = ; DESC = This trap is generated upon the occurrence \ of an E1 CSU Remote Alarm. \ Severity Level: MAJOR.; HELP = ; | ||
| NTF mcmT1CsuBlueAlarmClear | 1.3.6.1.4.1.335.1.4.29.0.6 | NAME = ; DESC = When a downstream node detects a loss of \ synchronization in its receive pair of a \ T1 line, it is in red alarm condition. \ In turn, it transmits a yellow alarm \ signal upstream to the previous node \ and a blue alarm signal downstream to \ the next node. This trap clears the \ node that has the Blue Alarm condition. \ Severity Level: INFORMATIVE.; HELP = ; | ||
| NTF mcmT1CsuBlueAlarmSet | 1.3.6.1.4.1.335.1.4.29.0.5 | NAME = ; DESC = When a downstream node detects a loss of \ synchronization in its receive pair of a \ T1 line, it is in red alarm condition. \ In turn, it transmits a yellow alarm \ signal upstream to the previous node \ and a blue alarm signal downstream to \ the next node.\ Severity Level: MINOR.; HELP = ; | ||
| INT mcmT1CsuGenStatusBlueAlarm | 1.3.6.1.4.1.335.1.4.29.2.2.1.5 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the \ T1 CSU blue alarm status.; HELP = ; CAPABILITIES = ; |
| mcmT1CsuGenStatusEntry | 1.3.6.1.4.1.335.1.4.29.2.2.1 | not-accessible | NAME = ; DESC = An entry in the T1 CSU General \ Status and Statistics table.; HELP = ; CAPABILITIES = ; | |
| INT mcmT1CsuGenStatusifIndex | 1.3.6.1.4.1.335.1.4.29.2.2.1.1 | INTEGER | read-only | NAME = ; DESC = The T1 CSU General Status interface \ index value of the specifc entry.; HELP = ; CAPABILITIES = ; |
| INT mcmT1CsuGenStatusLineStatus | 1.3.6.1.4.1.335.1.4.29.2.2.1.2 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the \ T1 CSU line status.; HELP = ; CAPABILITIES = ; |
| INT mcmT1CsuGenStatusLnCdViolations | 1.3.6.1.4.1.335.1.4.29.2.2.1.13 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the number \ of T1 CSU line code violations. \ Note that this is a 16-bit counter.; HELP = ; CAPABILITIES = ; |
| INT mcmT1CsuGenStatusRedAlarm | 1.3.6.1.4.1.335.1.4.29.2.2.1.3 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the \ T1 CSU red alarm status.; HELP = ; CAPABILITIES = ; |
| INT mcmT1CsuGenStatusRxCarrierLoss | 1.3.6.1.4.1.335.1.4.29.2.2.1.11 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the T1 \ CSU receive carrier loss status.; HELP = ; CAPABILITIES = ; |
| INT mcmT1CsuGenStatusRxElasStrEmpty | 1.3.6.1.4.1.335.1.4.29.2.2.1.8 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the T1 \ CSU receive elastic store empty status.; HELP = ; CAPABILITIES = ; |
| INT mcmT1CsuGenStatusRxElasStrFull | 1.3.6.1.4.1.335.1.4.29.2.2.1.7 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the T1 \ CSU receive elastic store full status.; HELP = ; CAPABILITIES = ; |
| INT mcmT1CsuGenStatusRxLevel | 1.3.6.1.4.1.335.1.4.29.2.2.1.6 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the T1 \ CSU line receive level status.; HELP = ; CAPABILITIES = ; |
| INT mcmT1CsuGenStatusRxLoopDnCdDetect | 1.3.6.1.4.1.335.1.4.29.2.2.1.15 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the T1 \ CSU receive loop down code status.; HELP = ; CAPABILITIES = ; |
| INT mcmT1CsuGenStatusRxLoopUpCdDetect | 1.3.6.1.4.1.335.1.4.29.2.2.1.14 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the T1 \ CSU receive loop up code status.; HELP = ; CAPABILITIES = ; |
| INT mcmT1CsuGenStatusRxPlsDensViolate | 1.3.6.1.4.1.335.1.4.29.2.2.1.9 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the T1 \ CSU receive pulse density violation status.; HELP = ; CAPABILITIES = ; |
| INT mcmT1CsuGenStatusRxSyncLoss | 1.3.6.1.4.1.335.1.4.29.2.2.1.12 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the T1 \ CSU receive loss of sync status.; HELP = ; CAPABILITIES = ; |
| mcmT1CsuGenStatusTable | 1.3.6.1.4.1.335.1.4.29.2.2 | not-accessible | NAME = ; DESC = The T1 CSU General Status and \ Statistics table.; HELP = ; CAPABILITIES = NET_DISP, VPN_DISP; | |
| INT mcmT1CsuGenStatusTxPlsDensViolate | 1.3.6.1.4.1.335.1.4.29.2.2.1.10 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the T1 \ CSU transmit pulse density violation status.; HELP = ; CAPABILITIES = ; |
| INT mcmT1CsuGenStatusYellowAlarm | 1.3.6.1.4.1.335.1.4.29.2.2.1.4 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the \ T1 CSU yellow alarm status.; HELP = ; CAPABILITIES = ; |
| NTF mcmT1CsuRedAlarmClear | 1.3.6.1.4.1.335.1.4.29.0.2 | NAME = ; DESC = When a downstream node is back in \ synchronization with its receive pair \ of a T1 line. This trap clears the node \ that has the Red Alarm condition. \ Severity Level : INFORMATIVE.; HELP = ; | ||
| NTF mcmT1CsuRedAlarmSet | 1.3.6.1.4.1.335.1.4.29.0.1 | NAME = ; DESC = When a downstream node detects a loss of \ synchronization in its receive pair of a \ T1 line, it is in red alarm condition. \ Severity Level: CRITICAL.; HELP = ; | ||
| NTF mcmT1CsuYellowAlarmClear | 1.3.6.1.4.1.335.1.4.29.0.4 | NAME = ; DESC = When a downstream node detects a loss of \ synchronization in its receive pair of a \ T1 line, it is in red alarm condition. \ In turn, it transmits a yellow alarm \ signal upstream to the previous node. \ This trap clears the node that has the \ Yellow Alarm condition.; Severity Level: INFORMATIVE.; HELP = ; | ||
| NTF mcmT1CsuYellowAlarmSet | 1.3.6.1.4.1.335.1.4.29.0.3 | NAME = ; DESC = When a downstream node detects a loss of \ synchronization in its receive pair of a \ T1 line, it is in red alarm condition. \ In turn, it transmits a yellow alarm \ signal upstream to the previous node. \ Severity Level: MAJOR.; HELP = ; | ||
| INT mcmT1E1CsuCfgDS0BasicRate | 1.3.6.1.4.1.335.1.4.29.1.1.1.7 | INTEGER | read-write | NAME = ; DESC = The value of this object selects the T1/E1 CSU \ line speed to be a multiple of the specified \ basic rate. E.g., Line Speed 256K = 4 x 64K.; HELP = ; CAPABILITIES = ; |
| STR mcmT1E1CsuCfgDS0Connection | 1.3.6.1.4.1.335.1.4.29.1.1.1.20 | DisplayString | read-write | NAME = ; DESC = The value of this object selects the DS0 \ channels for the T1/E1 CSU line connection. \ Valid characters are decimal digits, comma \ (','), and hyphen ('-').; HELP = Comma (',') is used as a delimiter between \ individual channel selections. \ e.g., 13,16 means DS0 channels 13 and 16. \ Hyphen ('-') is used only in Set operations \ to indicate a range of DS0 channels. \ e.g., 2,5-8 means DS0 channels 2,5,6,7, and 8.; CAPABILITIES = ; |
| mcmT1E1CsuCfgEntry | 1.3.6.1.4.1.335.1.4.29.1.1.1 | not-accessible | NAME = ; DESC = An entry in the T1/E1 CSU Configuration \ table.; HELP = ; CAPABILITIES = ; | |
| INT mcmT1E1CsuCfgFrameFmt | 1.3.6.1.4.1.335.1.4.29.1.1.1.12 | INTEGER | read-write | NAME = ; DESC = The value of this object selects the T1 CSU \ frame format. \ Note that for an E1 CSU interface, this object is not used.; HELP = ; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgFramerLoopback | 1.3.6.1.4.1.335.1.4.29.1.1.1.10 | INTEGER | read-write | NAME = ; DESC = The value of this object selects the T1/E1 CSU \ framer loopback.; HELP = ; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgifIndex | 1.3.6.1.4.1.335.1.4.29.1.1.1.1 | INTEGER | read-only | NAME = ; DESC = The T1E1 Csu Cfg interface index \ value of the specifc entry.; HELP = ; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgLineBuildOut | 1.3.6.1.4.1.335.1.4.29.1.1.1.4 | INTEGER | read-write | NAME = ; DESC = The value of this object selects the T1/E1 CSU \ line build out. For a T1 CSU, the default value \ is neg-7pt5-db (6). For an E1 CSU, the default \ value is either ohm-75-normal (9) (an E1 CSU interface \ with 2 BNC connectors) or ohm-120-normal (10) \ (an E1 CSU interface with an RJ48 connector). \ Note that the ranges of enumeration values 1-8 and \ 9-15 apply uniquely to T1 and E1 interfaces; respectively.; HELP = ; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgLineSpeed | 1.3.6.1.4.1.335.1.4.29.1.1.1.3 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates the T1/E1 CSU \ total configured DS0 line speed.; HELP = ; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgLineType | 1.3.6.1.4.1.335.1.4.29.1.1.1.2 | INTEGER | read-only | NAME = ; DESC = The value of this object determines \ whether the line is a T1 CSU or E1 CSU.; HELP = ; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgLocalLoopback | 1.3.6.1.4.1.335.1.4.29.1.1.1.8 | INTEGER | read-write | NAME = ; DESC = The value of this object selects the T1/E1 CSU \ local loopback.; HELP = ; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgPayloadLoopback | 1.3.6.1.4.1.335.1.4.29.1.1.1.15 | INTEGER | read-write | NAME = ; DESC = The value of this object selects the T1 CSU \ payload loopback. \ Note that for an E1 CSU interface, this object is not used.; HELP = ; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgRemoteLoopback | 1.3.6.1.4.1.335.1.4.29.1.1.1.9 | INTEGER | read-write | NAME = ; DESC = The value of this object selects the T1/E1 CSU \ remote loopback.; HELP = ; CAPABILITIES = ; |
| mcmT1E1CsuCfgTable | 1.3.6.1.4.1.335.1.4.29.1.1 | not-accessible | NAME = ; DESC = The T1/E1 CSU Configuration table.; HELP = ; CAPABILITIES = NET_CFG, VPN_CFG; | |
| INT mcmT1E1CsuCfgTransmitLoopDown | 1.3.6.1.4.1.335.1.4.29.1.1.1.17 | INTEGER | read-write | NAME = ; DESC = The value of this object selects the T1 CSU \ transmit loop down. \ Note that for an E1 CSU interface, this object is not used.; HELP = ; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgTransmitLoopUp | 1.3.6.1.4.1.335.1.4.29.1.1.1.16 | INTEGER | read-write | NAME = ; DESC = The value of this object selects the T1 CSU \ transmit loop up. \ Note that for an E1 CSU interface, this object is not used.; HELP = ; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgTrapEnable | 1.3.6.1.4.1.335.1.4.29.1.1.1.11 | INTEGER | read-write | NAME = ; DESC = The value of this object selects whether the T1/E1 \ CSU traps should be generated for this interface.; HELP = ; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgTxB7ZeroSuppress | 1.3.6.1.4.1.335.1.4.29.1.1.1.14 | INTEGER | read-write | NAME = ; DESC = The value of this object selects bit 7 zero\ suppression for a T1 CSU interface. Selects stuffing \ bit 7 to 1 if 8 consecutive zeros occurred. \ Note that for an E1 CSU interface, this object is not used.; HELP = b7zsDisable (1): no stuffing occurred. \ b7zsEnable (2): bit 7 forced to a one in \ channels with all zeros.; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgTxIdleCode | 1.3.6.1.4.1.335.1.4.29.1.1.1.5 | INTEGER | read-write | NAME = ; DESC = The value of this object selects the T1/E1 CSU \ transmit idle code. For a T1 CSU, the default value is \ hex 0x7F. For an E1 CSU, the default value is hex 0x55.; HELP = ; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgTxRx0CodeSuppress | 1.3.6.1.4.1.335.1.4.29.1.1.1.13 | INTEGER | read-write | NAME = ; DESC = The value of this object selects zero \ code suppression for a T1 CSU interface. \ Note that for an E1 CSU interface, this object is not used.; HELP = ; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgTxRxClkSource | 1.3.6.1.4.1.335.1.4.29.1.1.1.6 | INTEGER | read-write | NAME = ; DESC = The value of this object selects the T1/E1 CSU \ line clocking source.; HELP = ; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgTxRxCRC4 | 1.3.6.1.4.1.335.1.4.29.1.1.1.19 | INTEGER | read-write | NAME = ; DESC = The value of this object selects the E1 CSU CRC4. \ Note that for a T1 CSU interface, this object is not used.; HELP = ; CAPABILITIES = ; |
| INT mcmT1E1CsuCfgTxRxHDB3 | 1.3.6.1.4.1.335.1.4.29.1.1.1.18 | INTEGER | read-write | NAME = ; DESC = The value of this object selects the E1 CSU HDB3. \ Note that for a T1 CSU interface, this object is not used.; HELP = ; CAPABILITIES = ; |
| mcmT1E1CsuCntlRegStatusEntry | 1.3.6.1.4.1.335.1.4.29.2.1.1 | not-accessible | NAME = ; DESC = An entry in the T1/E1 CSU Control Register \ Status table.; HELP = ; CAPABILITIES = ; | |
| mcmT1E1CsuCntlRegStatusTable | 1.3.6.1.4.1.335.1.4.29.2.1 | not-accessible | NAME = ; DESC = The T1/E1 CSU Control Register Status \ table.; HELP = ; CAPABILITIES = NET_DISP, VPN_DISP; | |
| INT mcmT1E1CSUStatusCntlReg1 | 1.3.6.1.4.1.335.1.4.29.2.1.1.2 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates RCR1, the \ value of Receive Control Register 1 for a T1/E1 \ CSU line type.; HELP = ; CAPABILITIES =; |
| INT mcmT1E1CSUStatusCntlReg10 | 1.3.6.1.4.1.335.1.4.29.2.1.1.11 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates LICR, the \ value of the Line Interface Control Register for \ an E1 CSU line type. \ Note that for a T1 CSU interface, this object is not used.; HELP = ; CAPABILITIES =; |
| INT mcmT1E1CSUStatusCntlReg2 | 1.3.6.1.4.1.335.1.4.29.2.1.1.3 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates RCR2, the \ value of Receive Control Register 2 for a T1/E1 \ CSU line type.; HELP = ; CAPABILITIES =; |
| INT mcmT1E1CSUStatusCntlReg3 | 1.3.6.1.4.1.335.1.4.29.2.1.1.4 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates TCR1, the \ value of Transmit Control Register 1 for a T1/E1 \ CSU line type.; HELP = ; CAPABILITIES =; |
| INT mcmT1E1CSUStatusCntlReg4 | 1.3.6.1.4.1.335.1.4.29.2.1.1.5 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates TCR2, the \ value of Transmit Control Register 2 for a T1/E1 \ CSU line type.; HELP = ; CAPABILITIES =; |
| INT mcmT1E1CSUStatusCntlReg5 | 1.3.6.1.4.1.335.1.4.29.2.1.1.6 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates CCR1, the \ value of Common Control Register 1 for a T1/E1 \ CSU line type.; HELP = ; CAPABILITIES =; |
| INT mcmT1E1CSUStatusCntlReg6 | 1.3.6.1.4.1.335.1.4.29.2.1.1.7 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates CCR2, the \ value of Common Control Register 2 for a T1/E1 \ CSU line type.; HELP = ; CAPABILITIES =; |
| INT mcmT1E1CSUStatusCntlReg7 | 1.3.6.1.4.1.335.1.4.29.2.1.1.8 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates CCR3, the \ value of Common Control Register 3 for a T1/E1 \ CSU line type.; HELP = ; CAPABILITIES =; |
| INT mcmT1E1CSUStatusCntlReg8 | 1.3.6.1.4.1.335.1.4.29.2.1.1.9 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates LICR, the value of \ the Line Interface Control Register for a T1 CSU line type.\ The value of this object indicates CCR4, the value of \ Common Control Register 4 for an E1 line type.; HELP = ; CAPABILITIES =; |
| INT mcmT1E1CSUStatusCntlReg9 | 1.3.6.1.4.1.335.1.4.29.2.1.1.10 | INTEGER | read-only | NAME = ; DESC = The value of this object indicates CCR5, the \ value of Common Control Register 5 for an E1 CSU \ line type. \ Note that for a T1 CSU interface, this object is not used.; HELP = ; CAPABILITIES =; |
| INT mcmT1E1CSUStatusifIndex | 1.3.6.1.4.1.335.1.4.29.2.1.1.1 | INTEGER | read-only | NAME = ; DESC = The T1E1 CSU Status interface index \ value of the specifc entry.; HELP = ; CAPABILITIES = ; |
| micom_csu | 1.3.6.1.4.1.335.1.4.29 |
RFC description
Supports T1/E1 CSU configuration and status monitoring for MICOM Frame Relay Access devices.
Start monitoring MICOM Communications T1/E1 CSU equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.