All MIBs › MICOM-SYS-MIB
Category: Network Management
Description: Monitors MICOM system-level resources including CPU, memory, and chassis health.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is MICOM-SYS-MIB?
MICOM-SYS-MIB is a MICOM Communications enterprise MIB providing system-level identity and configuration objects for MICOM networking and WAN access equipment. It exposes hardware inventory data such as model type, hardware revision level, manufacture date, serial number, module ID, and MAC address, alongside CPU configuration and primary WAN/DCE serial port physical-media settings. Administrators performing MICOM-SYS-MIB SNMP polling use it to confirm a unit's hardware identity and revision level after a deployment or RMA, verify the CPU configuration and WAN port media type match the intended provisioning, and check chassis-level grouping objects for overall system status. As a system-identity module it typically complements the standard MIB-II/IF-MIB interface counters and any MICOM product-specific MIBs that expose deeper operational or fault data. It is deployed on MICOM Communications WAN access and networking devices in enterprise and carrier access environments where hardware inventory tracking and CPU/serial-port configuration verification are routine operational tasks.
IPNetwork Monitor allows you to monitor SNMP objects defined in MICOM-SYS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- MICOM Communications WAN access/networking equipment
Monitoring Examples
An administrator would poll mcmSysHWTypeModelType, mcmSysHWTypeRevisionLevel, and mcmSysHWTypeSerialNumber to confirm a replacement unit matches the expected model and hardware revision after a field swap. Checking mcmSysHWTypeMACAddress against inventory records verifies the unit's identity on the network, while mcmSysCfgCPUConfiguration and mcmSysCfgPrimaryWANPortPhyMedia (along with mcmSysCfgDCESerialPortPhyMedia) are reviewed to confirm the CPU and WAN/serial port physical media settings match the intended configuration. The mcmSysHWTypeGroup, mcmSysCfgGroup, and mcmSysChassisGroup conformance groups define which of these hardware, configuration, and chassis objects an agent is expected to implement.
What Can Be Monitored
- hardware model/revision identity
- serial number and MAC address
- CPU configuration
- WAN/serial port physical media type
- chassis inventory status
This MIB depends on
Related MIBs
Imported Objects
From MICOM-OSCAR-MIB
| micom-oscar |
From RFC-1212
| OBJECT-TYPE |
From RFC-1215
| TRAP-TYPE |
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| TimeTicks |
From SNMPv2-TC
| DisplayString |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| STR mcmSysAsciiTimeOfDay | 1.3.6.1.4.1.335.1.4.1.1.5.2 | DisplayString | read-only | NAME = ; DESC = This object will give the ascii version of \ the time of day. This would be the same time \ as reflected by all the other objects of \ this group put togther; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| NTF mcmSysBandwidthUtilExceeded | 1.3.6.1.4.1.335.1.4.1.0.7 | NAME = ; DESC = System TRAP message: Indication of Bandwidth \ Utilization exceeded for configured threshold.\ Severity Level: MAJOR.; HELP = The access device has exceeded its Configured \ threshold value for its bandwidth utilization. \ This value can be changed using set sys traps \ bandwidth 1-100 or Consult your system \ Administrator, or Field Personnel if this value needs \ to be changed.; | ||
| NTF mcmSysBatteryLow | 1.3.6.1.4.1.335.1.4.1.0.4 | NAME = ; DESC = System TRAP message: Indication of Battery Low.\ Severity Level: MINOR.; HELP = The access device is experiencing a Battery \ Low condition. Please contact the System \ Administrator or Field Personnel.; | ||
| INT mcmSysCfgCPUConfiguration | 1.3.6.1.4.1.335.1.4.1.1.2.1 | INTEGER | read-only | NAME = ; DESC = The CPU configuration for this access device.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysCfgDCESerialPortPhyMedia | 1.3.6.1.4.1.335.1.4.1.1.2.4 | INTEGER | read-only | NAME = ; DESC = Indicates the detected DCE \ serial port on the access \ device.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysCfgDRAMSize | 1.3.6.1.4.1.335.1.4.1.1.2.8 | INTEGER | read-only | NAME = ; DESC = Total installed DRAM memory size in megabytes.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysCfgFeatureRTCBatteryStatus | 1.3.6.1.4.1.335.1.4.1.1.2.7 | INTEGER | read-only | NAME = ; DESC = TimeOfDay/SRAM module detected.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysCfgFlashMemorySize | 1.3.6.1.4.1.335.1.4.1.1.2.9 | INTEGER | read-only | NAME = ; DESC = Total installed Flash memory size in megabytes.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| mcmSysCfgGroup | 1.3.6.1.4.1.335.1.4.1.1.2 | |||
| STR mcmSysCfgLock | 1.3.6.1.4.1.335.1.4.1.2.2.1 | DisplayString | read-write | NAME = ; DESC = Indicates if system config is locked.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| mcmSysCfgLockGroup | 1.3.6.1.4.1.335.1.4.1.2.2 | |||
| INT mcmSysCfgPrimaryWANPort | 1.3.6.1.4.1.335.1.4.1.1.2.2 | INTEGER | read-only | NAME = ; DESC = Indicates the presence of the \ Primary WAN port.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysCfgPrimaryWANPortPhyMedia | 1.3.6.1.4.1.335.1.4.1.1.2.3 | INTEGER | read-only | NAME = ; DESC = Indicates the physical media of Primary WAN port.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysCfgQUICCExpansionModule1 | 1.3.6.1.4.1.335.1.4.1.1.2.5 | INTEGER | read-only | NAME = ; DESC = QUICC Expansion module detected.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysCfgQUICCExpansionModule2 | 1.3.6.1.4.1.335.1.4.1.1.2.6 | INTEGER | read-only | NAME = ; DESC = QUICC Expansion module-2 is detected.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysChassisCoolingFan | 1.3.6.1.4.1.335.1.4.1.1.4.2 | INTEGER | read-only | NAME = ; DESC =Chassis cooling fan status.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| NTF mcmSysChassisFanFailure | 1.3.6.1.4.1.335.1.4.1.0.2 | NAME = ; DESC = System TRAP message: indication of a chassis \ FAN failure on the access device.\ Severity Level: MINOR.; HELP = Fan is not running. Please contact the System\ administrator, or Filed Personnel.; | ||
| mcmSysChassisGroup | 1.3.6.1.4.1.335.1.4.1.1.4 | |||
| INT mcmSysChassisNumberOfModules | 1.3.6.1.4.1.335.1.4.1.1.4.1 | INTEGER | read-only | NAME = ; DESC = Chassis style: number of modules.; NOTE : this object was previously named \ mcmSysChassisNumberOfSlots.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysChassisPowerSupplyModuleCount | 1.3.6.1.4.1.335.1.4.1.1.4.5 | INTEGER | read-only | NAME = ; DESC = Specifies the number of power \ supply modules installed; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysChassisPowerSupplyRedundant | 1.3.6.1.4.1.335.1.4.1.1.4.6 | INTEGER | read-only | NAME = ; DESC = Indicates whether there are \ redundant power supply modules; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysChassisPowerSupplyStatus | 1.3.6.1.4.1.335.1.4.1.1.4.4 | INTEGER | read-only | NAME = ; DESC = Fault indicates that at least one \ power supply module is down; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysChassisPowerSupplyType | 1.3.6.1.4.1.335.1.4.1.1.4.3 | INTEGER | read-only | NAME = ; DESC = Specifies the type of power supply \ based on type of voltage; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| STR mcmSysCommitTrackingCommunityOfLastCommit | 1.3.6.1.4.1.335.1.4.1.1.12.3 | DisplayString | read-only | NAME = ; DESC = The community of the last successful SET.; HELP = ; CAPABILITIES = NET_CFG, VPN_NONE; |
| CTR mcmSysCommitTrackingCounter | 1.3.6.1.4.1.335.1.4.1.1.12.1 | Counter | read-only | NAME = ; DESC = The Counter that pertains to the Commit Tracking.; HELP = ; CAPABILITIES = NET_CFG, VPN_NONE; |
| mcmSysCommitTrackingGroup | 1.3.6.1.4.1.335.1.4.1.1.12 | |||
| IP mcmSysCommitTrackingSrcIPAddressOfLastCommit | 1.3.6.1.4.1.335.1.4.1.1.12.2 | IpAddress | read-only | NAME = ; DESC = The IP address of the SNMP manager that issued \ the last successful SET operation.; HELP = ; CAPABILITIES = NET_CFG, VPN_NONE; |
| TIK mcmSysCommitTrackingTimeOfLastCommit | 1.3.6.1.4.1.335.1.4.1.1.12.4 | TimeTicks | read-only | NAME = ; DESC = The system uptime in ticks when the last \ SET was serviced.; HELP = ; CAPABILITIES = NET_CFG, VPN_NONE; |
| STR mcmSysCommunityStringCommunity | 1.3.6.1.4.1.335.1.4.1.1.9.1.2 | DisplayString | read-write | NAME = ; DESC = Community String used as access password.; HELP = ; CAPABILITIES = ; |
| mcmSysCommunityStringEntry | 1.3.6.1.4.1.335.1.4.1.1.9.1 | not-accessible | NAME = ; DESC = Entry that pertains to the Community \ string.; HELP = ; CAPABILITIES = ; | |
| INT mcmSysCommunityStringIndex | 1.3.6.1.4.1.335.1.4.1.1.9.1.1 | INTEGER | read-write | NAME = ; DESC = The Index value for each Community Strings.; HELP = ; CAPABILITIES = ; |
| mcmSysCommunityStringTable | 1.3.6.1.4.1.335.1.4.1.1.9 | not-accessible | NAME = ; DESC = The System Community String Table.; HELP = ; CAPABILITIES = NET_CFG, VPN_NONE; | |
| NTF mcmSysConfigChanged | 1.3.6.1.4.1.335.1.4.1.0.5 | NAME = ; DESC = An indication of configuration change in \ the access device.\ Severity Level: MAJOR.; HELP = Configuration has changed in access device. Please \ consult the System Administrator, or Field Personnel \ if the configuration has affected your applications.; | ||
| INT mcmSysConsolePortBaudRate | 1.3.6.1.4.1.335.1.4.1.1.11.1 | INTEGER | read-write | NAME = ; DESC = Set Console (and Debugger) Speed; HELP = Set Console Speed; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysConsolePortDataBits | 1.3.6.1.4.1.335.1.4.1.1.11.3 | INTEGER | read-write | NAME = ; DESC = Set Console number of Data bits (excluding start, \ stop and parity bits); HELP = Set Console number of Data bits (excluding start, \ stop and parity bits); CAPABILITIES = NET_CFG, VPN_DISP; |
| mcmSysConsolePortGroup | 1.3.6.1.4.1.335.1.4.1.1.11 | |||
| INT mcmSysConsolePortParity | 1.3.6.1.4.1.335.1.4.1.1.11.4 | INTEGER | read-write | NAME = ; DESC = Set Console parity bit; HELP = Set Console parity bit; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysConsolePortStopBits | 1.3.6.1.4.1.335.1.4.1.1.11.2 | INTEGER | read-write | NAME = ; DESC = Set Console number of stop bits; HELP = Set Console number of stop bits; CAPABILITIES = NET_CFG, VPN_DISP; |
| NTF mcmSysCPUUtilExceeded | 1.3.6.1.4.1.335.1.4.1.0.6 | NAME = ; DESC = System TRAP message: Indication of CPU Utilization \ exceeded for configured threshold.\ Severity Level: MAJOR.; HELP = The access device has exceeded its configured threshold \ value for CPU Utilization. This value can be changed using set sys traps cpu 1 - 100.\ Or Consult your system Administrator, or field Personnel if \ this value needs to be changed.; | ||
| GAU mcmSysCpuUtilization | 1.3.6.1.4.1.335.1.4.1.3.1.1 | Gauge | read-only | NAME = ; DESC = Indicates the CPU utilization in percent.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysFirmwareCodeCommitBank | 1.3.6.1.4.1.335.1.4.1.1.6.7 | INTEGER | read-write | NAME = ; DESC =The Bank that the Code is committed from.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysFirmwareCodeReadBank | 1.3.6.1.4.1.335.1.4.1.1.6.6 | INTEGER | read-only | NAME = ; DESC =The Bank that the Code Read from.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysFirmwareConfigActiveBank | 1.3.6.1.4.1.335.1.4.1.1.6.4 | INTEGER | read-write | NAME = ; DESC = The active Configuration Image Bank.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysFirmwareConfigCommitBank | 1.3.6.1.4.1.335.1.4.1.1.6.2 | INTEGER | read-write | NAME = ; DESC = The Default Confi. Image (global).; HELP = Committed Config. Image Bank.; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysFirmwareConfigReadBank | 1.3.6.1.4.1.335.1.4.1.1.6.5 | INTEGER | read-only | NAME = ; DESC = The Bank that the Configuration Read from.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysFirmwareConfigSaveBank | 1.3.6.1.4.1.335.1.4.1.1.6.3 | INTEGER | read-write | NAME = ; DESC = Default Software Image Bank.; HELP = Committed Code Image (global).; CAPABILITIES = NET_CFG, VPN_DISP; |
| STR mcmSysFirmwareConfigVersion | 1.3.6.1.4.1.335.1.4.1.1.6.9 | DisplayString | read-only | NAME = ; DESC = The Configuration Version that this \ access device is running on.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| mcmSysFirmwareGroup | 1.3.6.1.4.1.335.1.4.1.1.6 | |||
| INT mcmSysFirmwareImageBank | 1.3.6.1.4.1.335.1.4.1.1.7.1.2 | INTEGER | read-only | NAME = ; DESC = The Specific ImageBank that holds the Code \ Image or Config Image.; HELP = ; CAPABILITIES = ; |
| CTR mcmSysFirmwareImageBurnCount | 1.3.6.1.4.1.335.1.4.1.1.7.1.8 | Counter | read-only | NAME = ; DESC = This indicates the global burn count.; HELP = ; CAPABILITIES = ; |
| INT mcmSysFirmwareImageCommitStatus | 1.3.6.1.4.1.335.1.4.1.1.7.1.7 | INTEGER | read-only | NAME = ; DESC = This indicates the Firmware Image Commit Status.; HELP = ; CAPABILITIES = ; |
| mcmSysFirmwareImageEntry | 1.3.6.1.4.1.335.1.4.1.1.7.1 | not-accessible | NAME = ; DESC = The entry that pertains to Code Image.; HELP = ; CAPABILITIES = ; | |
| STR mcmSysFirmwareImageFilename | 1.3.6.1.4.1.335.1.4.1.1.7.1.4 | DisplayString | read-only | NAME = ; DESC =This indicates the File name of the Firmware.; HELP = ; CAPABILITIES = ; |
| INT mcmSysFirmwareImageIndex | 1.3.6.1.4.1.335.1.4.1.1.7.1.1 | INTEGER | read-only | NAME = ; DESC = The Index value for a specific Image.; HELP = ; CAPABILITIES = ; |
| STR mcmSysFirmwareImageRevision | 1.3.6.1.4.1.335.1.4.1.1.7.1.5 | DisplayString | read-only | NAME = ; DESC = This indicates the Revision level of the \ specific Firmware.; HELP = ; CAPABILITIES = ; |
| INT mcmSysFirmwareImageSize | 1.3.6.1.4.1.335.1.4.1.1.7.1.6 | INTEGER | read-only | NAME = ; DESC = This indicates the size of the Firmware in bytes.; HELP = ; CAPABILITIES = ; |
| INT mcmSysFirmwareImageSoftware | 1.3.6.1.4.1.335.1.4.1.1.7.1.3 | INTEGER | read-only | NAME = ; DESC = This indicates that the specific Software \ is a boot Code, Image Code or a Config Code.; HELP = ; CAPABILITIES = ; |
| mcmSysFirmwareImageTable | 1.3.6.1.4.1.335.1.4.1.1.7 | not-accessible | NAME = ; DESC = The Firmware Image Table contains \ information about the Code Image.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; | |
| STR mcmSysFirmwareVersion | 1.3.6.1.4.1.335.1.4.1.1.6.8 | DisplayString | read-only | NAME = ; DESC = The Code Version that this access \ device is running on.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| STR mcmSysHWTypeCPUType | 1.3.6.1.4.1.335.1.4.1.1.1.7 | DisplayString | read-only | NAME = ; DESC = Indicates the CPU type for this \ access device; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysHWTypeGenCfgType | 1.3.6.1.4.1.335.1.4.1.1.1.8 | INTEGER | read-only | NAME = ; DESC = Indicates the model type for this \ access device.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| mcmSysHWTypeGroup | 1.3.6.1.4.1.335.1.4.1.1.1 | |||
| OCT mcmSysHWTypeMACAddress | 1.3.6.1.4.1.335.1.4.1.1.1.6 | OCTET STRING | read-only | NAME = ; DESC = The base MAC address assigned \ to the access device.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| STR mcmSysHWTypeManufRevDate | 1.3.6.1.4.1.335.1.4.1.1.1.3 | DisplayString | read-only | NAME = ; DESC = The manufacture/revision date \ of the access device .; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| STR mcmSysHWTypeModelType | 1.3.6.1.4.1.335.1.4.1.1.1.1 | DisplayString | read-only | NAME = ; DESC = **NOTE: THIS OBJECT HAS BEEN \ DEPRECATED. Its functionality \ has been replaced by the \ mcmSysHWTypeCPUType object \ located below in this group.**\ \ The model name/type of the \ access device.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysHWTypeModuleID | 1.3.6.1.4.1.335.1.4.1.1.1.5 | INTEGER | read-only | NAME = ; DESC = The module ID of the access \ device.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysHWTypeRevisionLevel | 1.3.6.1.4.1.335.1.4.1.1.1.2 | INTEGER | read-only | NAME = ; DESC = The revision level of the \ access device.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| STR mcmSysHWTypeSerialNumber | 1.3.6.1.4.1.335.1.4.1.1.1.4 | DisplayString | read-only | NAME = ; DESC = The serial number of \ the access device..; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysIfExtChannel | 1.3.6.1.4.1.335.1.4.1.1.13.1.10 | INTEGER | read-only | NAME = ; DESC = The channel number of this interface... \ FR DCE: N/A, WAN Driver: SCC number, \ WAN Connector: corresponding SCC number; HELP = ; CAPABILITIES = ; |
| INT mcmSysIfExtConnectorPresent | 1.3.6.1.4.1.335.1.4.1.1.13.1.5 | INTEGER | read-only | NAME = ; DESC = This indicates if the IfExt entry \ has a phisical connector present.; HELP = ; CAPABILITIES = ; |
| mcmSysIfExtEntry | 1.3.6.1.4.1.335.1.4.1.1.13.1 | not-accessible | NAME = ; DESC = The specific Entry that pertains to \ IfExt in this access device.; HELP = ; CAPABILITIES = ; | |
| INT mcmSysIfExtIfIndex | 1.3.6.1.4.1.335.1.4.1.1.13.1.1 | INTEGER | read-only | NAME = ; DESC = The Index value of the specifc entry.; HELP = ; CAPABILITIES = ; |
| INT mcmSysIfExtLinkUpDownTrapEnable | 1.3.6.1.4.1.335.1.4.1.1.13.1.4 | INTEGER | read-write | NAME = ; DESC = This indicates if the LinkUpDownTrap \ is enabled or not.; HELP = ; CAPABILITIES = ; |
| INT mcmSysIfExtModule | 1.3.6.1.4.1.335.1.4.1.1.13.1.9 | INTEGER | read-only | NAME = ; DESC = The logical interface module address \ of this interface \ NOTE : this object was previously named \ mcmSysIfExtSlot.; HELP = ; CAPABILITIES = ; |
| STR mcmSysIfExtName | 1.3.6.1.4.1.335.1.4.1.1.13.1.2 | DisplayString | read-only | NAME = ; DESC = The Name of the specific IfExt entry.; HELP = ; CAPABILITIES = ; |
| INT mcmSysIfExtPersistenceType | 1.3.6.1.4.1.335.1.4.1.1.13.1.6 | INTEGER | read-only | NAME = ; DESC = This indicates if the Persistence Type \ is volatile or non-volatile.; HELP = ; CAPABILITIES = ; |
| INT mcmSysIfExtPPA | 1.3.6.1.4.1.335.1.4.1.1.13.1.8 | INTEGER | read-only | NAME = ; DESC = The PPA of the port; HELP = ; CAPABILITIES = ; |
| INT mcmSysIfExtPPADeviceType | 1.3.6.1.4.1.335.1.4.1.1.13.1.11 | INTEGER | read-only | NAME = ; DESC = The PPA device type of this interface.; HELP = ; CAPABILITIES = ; |
| INT mcmSysIfExtState | 1.3.6.1.4.1.335.1.4.1.1.13.1.7 | INTEGER | read-only | NAME = ; DESC = This indicates that if the IfExt entry \ is configured or not.; HELP = ; CAPABILITIES = ; |
| mcmSysIfExtTable | 1.3.6.1.4.1.335.1.4.1.1.13 | not-accessible | NAME = ; DESC = The Interface table that contains \ information about IfExtension in this \ access device.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; | |
| INT mcmSysIfExtType | 1.3.6.1.4.1.335.1.4.1.1.13.1.3 | INTEGER | read-only | NAME = ; DESC = The values of this field are kept \ the same as the values for the \ ifExtType defined in \ the extension to MIB II (RFC1573); HELP = ; CAPABILITIES = ; |
| GAU mcmSysInternalRAMUtilization | 1.3.6.1.4.1.335.1.4.1.3.1.3 | Gauge | read-only | NAME = ; DESC = Indicates internal RAM Utilization in percent.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysLastCommunityPriviledgeLevel | 1.3.6.1.4.1.335.1.4.1.1.10.2 | INTEGER | read-only | NAME = ; DESC = This parameter contains the priviledge \ level from the last valid password.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| mcmSysLimEntry | 1.3.6.1.4.1.335.1.4.1.1.3.1 | not-accessible | NAME = ; DESC = Entry pertaining to a specific logical module.; HELP = This includes the Name, Part number, and rev. level.; CAPABILITIES = ; | |
| STR mcmSysLimMfgDate | 1.3.6.1.4.1.335.1.4.1.1.3.1.6 | DisplayString | read-only | NAME = ; DESC = Displays the manufacturing date of the module in \ the specific location.; HELP = ; CAPABILITIES = ; |
| INT mcmSysLimModuleAddress | 1.3.6.1.4.1.335.1.4.1.1.3.1.1 | INTEGER | read-only | NAME = ; DESC = lim (logical interface module) identifies \ the address of the module within the unit; HELP = ; CAPABILITIES = ; |
| STR mcmSysLimModuleName | 1.3.6.1.4.1.335.1.4.1.1.3.1.2 | DisplayString | read-only | NAME = ; DESC = Displays the name of the module \ in the specific location; NOTE : this object was previously named \ mcmSysCardModuleName.; HELP = ; CAPABILITIES = ; |
| STR mcmSysLimPcbPartNumber | 1.3.6.1.4.1.335.1.4.1.1.3.1.3 | DisplayString | read-only | NAME = ; DESC = Displays the part number of the module in \ the specific location; HELP = ; CAPABILITIES = ; |
| STR mcmSysLimPcbRelease | 1.3.6.1.4.1.335.1.4.1.1.3.1.4 | DisplayString | read-only | NAME = ; DESC = Displays the release level of the module in \ the specific location.; HELP = ; CAPABILITIES = ; |
| STR mcmSysLimSerialNumber | 1.3.6.1.4.1.335.1.4.1.1.3.1.5 | DisplayString | read-only | NAME = ; DESC = Displays the serial number of the module in \ the specific location.; HELP = ; CAPABILITIES = ; |
| mcmSysLimTable | 1.3.6.1.4.1.335.1.4.1.1.3 | not-accessible | NAME = ; DESC = Table to view an individual Logical \ Interface Modules(LIM) on the access \ device.; HELP = Table to view the hardware \ CAPABILITIES = NET_CFG, VPN_DISP; | |
| GAU mcmSysLinkReceiveBandwidthUtilization | 1.3.6.1.4.1.335.1.4.1.3.1.4 | Gauge | read-only | NAME = ; DESC = Indicates the Link Receive Bandwidth utilization.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| GAU mcmSysLinkTransmitBandwidthUtilization | 1.3.6.1.4.1.335.1.4.1.3.1.2 | Gauge | read-only | NAME = ; DESC = Indicates the Bandwidth Utilization in percent.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysLogModuleAddress | 1.3.6.1.4.1.335.1.4.1.1.16.1.2 | INTEGER | read-only | NAME = ; DESC = The value of this object identifies \ the logical interface module (lim) address; HELP = ; CAPABILITIES = ; |
| NTF mcmSysMainPowerSupplyFailure | 1.3.6.1.4.1.335.1.4.1.0.1 | NAME = ; DESC = System TRAP message: indication of Power Supply \ failure.\ Severity Level: CRITICAL.; HELP = Power Supply Jumper may not be set properly.\ Please contact the System Administrator, or\ field Personnel.; | ||
| INT mcmSysOperationalType | 1.3.6.1.4.1.335.1.4.1.1.6.1 | INTEGER | read-write | NAME = ; DESC = Network Operational mode of this \ access device.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| mcmSysPhysEntry | 1.3.6.1.4.1.335.1.4.1.1.16.1 | not-accessible | NAME = ; DESC = Entry pertaining to a specific physical module.; HELP = ; CAPABILITIES = ; | |
| INT mcmSysPhysModuleAddress | 1.3.6.1.4.1.335.1.4.1.1.16.1.1 | INTEGER | read-only | NAME = ; DESC = The value of this object identifies \ the physical slot address of the module \ within the unit; HELP = ; CAPABILITIES = ; |
| mcmSysPhysTable | 1.3.6.1.4.1.335.1.4.1.1.16 | not-accessible | NAME = ; DESC = Table to map physical cards to \ Logical Interface Modules (LIM) on \ the access device HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; | |
| NTF mcmSysRAMUtilExceeded | 1.3.6.1.4.1.335.1.4.1.0.8 | NAME = ; DESC = System TRAP message: Indication of RAM \ Utilization exceeded for configured threshold.\ Severity Level: MAJOR.; HELP = It is an indication of surpassing the configured \ value for RAM utilization. This value can be changed using set sys traps ram 1-100 or Consult your system \ administrator, or Field Personnel if this value needs \ to be changed.; | ||
| INT mcmSysResetAction | 1.3.6.1.4.1.335.1.4.1.2.1.1 | INTEGER | write-only | NAME = ; DESC = Reset Unit, restart the CPU only, warm start \ or factory default (cold start).; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| mcmSysResetGroup | 1.3.6.1.4.1.335.1.4.1.2.1 | |||
| INT mcmSysRestartReason | 1.3.6.1.4.1.335.1.4.1.2.1.2 | INTEGER | read-only | NAME = ; DESC = Reset Restart Reason Codes; HELP = Reason Code for last Reset; CAPABILITIES = NET_CFG, VPN_DISP; |
| NTF mcmSysRollbackArmed | 1.3.6.1.4.1.335.1.4.1.0.11 | NAME = ; DESC = System TRAP message: Indication of System \ Rollback Feature armed, resulting from User \ committing/activating Code/Config Bank for \ next reset.\ Severity Level: INFORMATIVE.; HELP = This is an indication of user committing a new \ code bank/Config Bank after the access device \ is reset the next time around. If this \ condition is not needed, consult your System \ Admin. or Field personnel.; | ||
| INT mcmSysRollbackConfirm | 1.3.6.1.4.1.335.1.4.1.1.14.3 | INTEGER | write-only | NAME = ; DESC = This confirms that previous System Configuration \ or Code bank changes are accepted and that the \ System is NOT to timeout, reset and go back to previous Config or Code bank.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| NTF mcmSysRollbackDisabled | 1.3.6.1.4.1.335.1.4.1.0.10 | NAME = ; DESC = System TRAP message: Indication of System \ Rollback Feature disabled.\ Severity Level: INFORMATIVE.; HELP = This is an indication of the Rollback feature \ being disabled. Please enable this feature if \ it is required. Otherwise, consult your system \ admin. or Field Personnel.; | ||
| NTF mcmSysRollbackDisarmed | 1.3.6.1.4.1.335.1.4.1.0.12 | NAME = ; DESC = System TRAP message: Indication of System \ Rollback Feature confirmed for this session.\ Severity Level: INFORMATIVE.; HELP = This is a condition of disarming previously \ committed Code Bank/config Bank that was going \ to occur after a reset. If it is not desirable, \ reverse the condition., ; | ||
| NTF mcmSysRollbackEnabled | 1.3.6.1.4.1.335.1.4.1.0.9 | NAME = ; DESC = System TRAP message: Indication of System \ Rollback Feature enabled.\ Severity Level: INFORMATIVE.; HELP = This is an indication of the Rollback feature \ being enabled. Please disable this feature if \ it is not desired, or consult your System Admin.\ or Field Personnel.; | ||
| INT mcmSysRollbackFeature | 1.3.6.1.4.1.335.1.4.1.1.14.1 | INTEGER | read-write | NAME = ; DESC = This indicates if the RollBack feature is \ enabled or disabled.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| mcmSysRollbackGroup | 1.3.6.1.4.1.335.1.4.1.1.14 | |||
| INT mcmSysRollbackStatus | 1.3.6.1.4.1.335.1.4.1.1.14.2 | INTEGER | read-only | NAME = ; DESC = This indicates whether Confirm system \ Rollback is required or not. Or will \ Confirm at the next reset.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysSmartCfgAction | 1.3.6.1.4.1.335.1.4.1.1.8.1 | INTEGER | write-only | NAME = ; DESC = Directs system to update secondary (Flash) storage \ by saving present configuration. Or directs discard \ of present re-configures.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| mcmSysSmartCfgGroup | 1.3.6.1.4.1.335.1.4.1.1.8 | |||
| INT mcmSysSmartCfgStatus | 1.3.6.1.4.1.335.1.4.1.1.8.2 | INTEGER | read-only | NAME = ; DESC = Indicates if system is currently being \ re-configured.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| NTF mcmSysSystemReset | 1.3.6.1.4.1.335.1.4.1.0.3 | NAME = ; DESC = System TRAP message: indication of system Reset \ (warm start).\ Severity Level: INFORMATIVE.; HELP = A system reset has occured. If normal \ operation did not resume after the Reset, Please \ contact the System Administrator, or Field \ Personnel.; | ||
| mcmSysTimeOfDay | 1.3.6.1.4.1.335.1.4.1.1.5.1 | |||
| INT mcmSysTimeOfDayDate | 1.3.6.1.4.1.335.1.4.1.1.5.1.5 | INTEGER | read-write | NAME = ; DESC = System Time of day. The date.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysTimeOfDayDay | 1.3.6.1.4.1.335.1.4.1.1.5.1.4 | INTEGER | read-write | NAME = ; DESC = System Time of day, the Day.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| mcmSysTimeOfDayGroup | 1.3.6.1.4.1.335.1.4.1.1.5 | |||
| INT mcmSysTimeOfDayHour | 1.3.6.1.4.1.335.1.4.1.1.5.1.3 | INTEGER | read-write | NAME = ; DESC = System Time of day in hours.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysTimeOfDayMin | 1.3.6.1.4.1.335.1.4.1.1.5.1.2 | INTEGER | read-write | NAME = ; DESC = System Time of day in minutes.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysTimeOfDayMonth | 1.3.6.1.4.1.335.1.4.1.1.5.1.6 | INTEGER | read-write | NAME = ; DESC = System Time of day. The Month.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysTimeOfDaySec | 1.3.6.1.4.1.335.1.4.1.1.5.1.1 | INTEGER | read-write | NAME = ; DESC = System Time of day in seconds.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysTimeOfDayYear | 1.3.6.1.4.1.335.1.4.1.1.5.1.7 | INTEGER | read-write | NAME = ; DESC = System Time of day. The Year.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| STR mcmSysTimeOfLastReset | 1.3.6.1.4.1.335.1.4.1.2.1.3 | DisplayString | read-only | NAME = ; DESC = This object will indicate the time of \ when the access device was last reset. HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysTrapBandwidthUtilThreshold | 1.3.6.1.4.1.335.1.4.1.4.2.2 | INTEGER | read-write | NAME = ; DESC = Indicates the configured threshold for \ bandwidth utilization.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysTrapCPUUtilThreshold | 1.3.6.1.4.1.335.1.4.1.4.2.1 | INTEGER | read-write | NAME = ; DESC = Indicates the configured threshold for \ CPU Utilization.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysTrapRAMUtilThreshold | 1.3.6.1.4.1.335.1.4.1.4.2.3 | INTEGER | read-write | NAME = ; DESC = Indicates the configured threshold for \ RAM utilization.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| INT mcmSysTrapSubscriptionAction | 1.3.6.1.4.1.335.1.4.1.4.1.1.3 | INTEGER | read-write | NAME = ; DESC = Action to take: add or delete subscriber.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| STR mcmSysTrapSubscriptionCommunityString | 1.3.6.1.4.1.335.1.4.1.4.1.1.2 | DisplayString | read-write | NAME = ; DESC = Community string for this subscriber.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| mcmSysTrapSubscriptionEntry | 1.3.6.1.4.1.335.1.4.1.4.1.1 | not-accessible | NAME = ; DESC = Entry that pertains to a specific TRAP.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; | |
| IP mcmSysTrapSubscriptionIPAddress | 1.3.6.1.4.1.335.1.4.1.4.1.1.1 | IpAddress | read-write | NAME = ; DESC = IP address of the SNMP Manager subscribing Traps.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| mcmSysTrapSubscriptionTable | 1.3.6.1.4.1.335.1.4.1.4.1 | not-accessible | NAME = ; DESC = This Table displays the System Trap \ subscription information of this \ access device.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; | |
| mcmSysTrapThresholdGroup | 1.3.6.1.4.1.335.1.4.1.4.2 | |||
| mcmSysUtilGroup | 1.3.6.1.4.1.335.1.4.1.3.1 | |||
| STR mcmSysValidateCommunity | 1.3.6.1.4.1.335.1.4.1.1.10.1 | DisplayString | write-only | NAME = ; DESC = This parameter contains the password \ obtained by the command line user interface.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; |
| mcmSysValidateCommunityGroup | 1.3.6.1.4.1.335.1.4.1.1.10 | |||
| micom_system | 1.3.6.1.4.1.335.1.4.1 | |||
| INT nvmSysIfExtChannel | 1.3.6.1.4.1.335.1.4.1.1.15.1.10 | INTEGER | read-only | NAME = ; DESC = The channel number of this interface... \ FR DCE: N/A, WAN Driver: SCC number, \ WAN Connector: corresponding SCC number; HELP = ; CAPABILITIES = ; |
| INT nvmSysIfExtConnectorPresent | 1.3.6.1.4.1.335.1.4.1.1.15.1.5 | INTEGER | read-only | NAME = ; DESC = This indicates if the IfExt entry \ has a phisical connector present.; HELP = ; CAPABILITIES = ; |
| nvmSysIfExtEntry | 1.3.6.1.4.1.335.1.4.1.1.15.1 | not-accessible | NAME = ; DESC = The specific Entry that pertains to \ IfExt in this access device.; HELP = ; CAPABILITIES = ; | |
| INT nvmSysIfExtIfIndex | 1.3.6.1.4.1.335.1.4.1.1.15.1.1 | INTEGER | read-only | NAME = ; DESC = The Index value of the specifc entry.; HELP = ; CAPABILITIES = ; |
| INT nvmSysIfExtLinkUpDownTrapEnable | 1.3.6.1.4.1.335.1.4.1.1.15.1.4 | INTEGER | read-only | NAME = ; DESC = This indicates if the LinkUpDownTrap \ is enabled or not.; HELP = ; CAPABILITIES = ; |
| INT nvmSysIfExtModule | 1.3.6.1.4.1.335.1.4.1.1.15.1.9 | INTEGER | read-only | NAME = ; DESC = The logical interface module address \ of this interface \ NOTE : this object was previously named \ nvmSysIfExtSlot.; HELP = ; CAPABILITIES = ; |
| STR nvmSysIfExtName | 1.3.6.1.4.1.335.1.4.1.1.15.1.2 | DisplayString | read-only | NAME = ; DESC = The Name of the specific IfExt entry.; HELP = ; CAPABILITIES = ; |
| INT nvmSysIfExtPersistenceType | 1.3.6.1.4.1.335.1.4.1.1.15.1.6 | INTEGER | read-only | NAME = ; DESC = This indicates if the Persistence Type \ is volatile or non-volatile.; HELP = ; CAPABILITIES = ; |
| INT nvmSysIfExtPPA | 1.3.6.1.4.1.335.1.4.1.1.15.1.8 | INTEGER | read-only | NAME = ; DESC = The PPA of the port; HELP = ; CAPABILITIES = ; |
| INT nvmSysIfExtPPADeviceType | 1.3.6.1.4.1.335.1.4.1.1.15.1.11 | INTEGER | read-only | NAME = ; DESC = The PPA device type of this interface.; HELP = ; CAPABILITIES = ; |
| INT nvmSysIfExtState | 1.3.6.1.4.1.335.1.4.1.1.15.1.7 | INTEGER | read-only | NAME = ; DESC = This indicates that if the IfExt entry \ is configured or not.; HELP = ; CAPABILITIES = ; |
| nvmSysIfExtTable | 1.3.6.1.4.1.335.1.4.1.1.15 | not-accessible | NAME = ; DESC = The Interface table that contains \ information about IfExtension in this \ access device.; HELP = ; CAPABILITIES = NET_CFG, VPN_DISP; | |
| INT nvmSysIfExtType | 1.3.6.1.4.1.335.1.4.1.1.15.1.3 | INTEGER | read-only | NAME = ; DESC = The values of this field are kept \ the same as the values for the \ ifExtType defined in \ the extension to MIB II (RFC1573); HELP = ; CAPABILITIES = ; |
| sys_configuration | 1.3.6.1.4.1.335.1.4.1.1 | |||
| sys_control | 1.3.6.1.4.1.335.1.4.1.2 | |||
| sys_statistics | 1.3.6.1.4.1.335.1.4.1.3 | |||
| sys_trap | 1.3.6.1.4.1.335.1.4.1.4 |
RFC description
MICOM system management MIB with configuration, control, firmware, and device status information.
Start monitoring MICOM Communications WAN access/networking equipment (system identity) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.