ME1200-RMIRROR-MIB

All MIBs › ME1200-RMIRROR-MIB

Organization: Cisco Systems, Inc

Last Updated: 2014-05-08

Category: Switch Management

Description: Configures remote port mirroring (RSPAN) sessions on Cisco ME1200 switches.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ME1200-RMIRROR-MIB?

ME1200-RMIRROR-MIB is a Cisco proprietary module for the ME1200 Metro Ethernet switch family, configuring remote port mirroring (RSPAN-style) sessions used to copy traffic from source ports to a remote analysis destination. It exposes switch capability flags (reflector port and CPU mirror support), per-session configuration including mode, switch type, mirror VLAN ID, and CPU-based traffic sources per session. Its monitoring value is primarily configuration status for diagnostic tooling: administrators can confirm which mirror sessions are configured, their operating mode, and the VLAN used to carry mirrored traffic, which is essential when troubleshooting network issues via traffic capture. It depends on the switch's VLAN infrastructure (mirror VLAN ID) to transport mirrored frames across the stack/network. It is typically deployed on Cisco ME1200 switches when network engineers need to remotely capture and analyze traffic from ports on a metro Ethernet access switch. Engineers can download the ME1200-RMIRROR-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ME1200-RMIRROR-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco ME1200 Metro Ethernet switch

Monitoring Examples

An engineer would poll me1200RmirrorConfigSessionTable/Entry to check me1200RmirrorConfigSessionMode and me1200RmirrorConfigSessionVid, confirming a mirror session is active and using the intended VLAN for mirrored traffic delivery. If me1200RmirrorCapabilitiesReflectorPortSupport indicates the feature is unsupported but a session was configured expecting a reflector port, that mismatch would reveal why mirrored traffic is not reaching the analyzer.

What Can Be Monitored

remote mirror session configuration
mirror session mode
mirror VLAN ID
reflector/CPU mirror capability support
CPU traffic source per session

Imported Objects

From CISCOME1200-MIB

me1200SwitchMgmt

OBJECT-IDENTITY

From ME1200-TC

ME1200InterfaceIndex
ME1200Unsigned16

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

TEXTUAL-CONVENTION
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
me1200RmirrorMib	1.3.6.1.4.1.9.9.815.1.120			This is a private version of Rmirror
me1200RmirrorMibObjects	1.3.6.1.4.1.9.9.815.1.120.1
me1200RmirrorCapabilities	1.3.6.1.4.1.9.9.815.1.120.1.1
T/F me1200RmirrorCapabilitiesReflectorPortSupport	1.3.6.1.4.1.9.9.815.1.120.1.1.1	TruthValue	read-only	Indicate if reflector port is configurable or not. true(1) means supported. false(2) means not supported.
T/F me1200RmirrorCapabilitiesCpuMirrorSupport	1.3.6.1.4.1.9.9.815.1.120.1.1.2	TruthValue	read-only	Indicate if mirroring CPU traffic is supported or not. true(1) means supported. false(2) means not supported.
me1200RmirrorConfig	1.3.6.1.4.1.9.9.815.1.120.1.2
me1200RmirrorConfigSessionTable	1.3.6.1.4.1.9.9.815.1.120.1.2.1		not-accessible	This is a table of global configuration per session
me1200RmirrorConfigSessionEntry	1.3.6.1.4.1.9.9.815.1.120.1.2.1.1		not-accessible	Each session has a set of parameters
I32 me1200RmirrorConfigSessionSessionId	1.3.6.1.4.1.9.9.815.1.120.1.2.1.1.1	Integer32	not-accessible	Session ID.
T/F me1200RmirrorConfigSessionMode	1.3.6.1.4.1.9.9.815.1.120.1.2.1.1.2	TruthValue	read-write	Enable/Disable the mirror or Remote Mirroring function. true(1) is to enable the function. false(2) is to disable it.
ME1 me1200RmirrorConfigSessionSwitchType	1.3.6.1.4.1.9.9.815.1.120.1.2.1.1.3	ME1200RmirrorSwitchType	read-write	Switch type in rmirror. mirror(0) means to do the mirror function on the device. source(1) means the device acts as source node for monitor flow. intermediate(2) means the device acts as forwarding node for monitor flow. The object is to forward traffic from source switch to destination switch. destination(3) means the device acts as end node for moniot flow.
ME1 me1200RmirrorConfigSessionVid	1.3.6.1.4.1.9.9.815.1.120.1.2.1.1.4	ME1200Unsigned16	read-write	The VLAN ID points out where the monitor packet will copy to.
me1200RmirrorConfigSessionSourceCpuTable	1.3.6.1.4.1.9.9.815.1.120.1.2.2		not-accessible	This is a table of source CPU configuration per session
me1200RmirrorConfigSessionSourceCpuEntry	1.3.6.1.4.1.9.9.815.1.120.1.2.2.1		not-accessible	Each session has a set of parameters
I32 me1200RmirrorConfigSessionSourceCpuSessionId	1.3.6.1.4.1.9.9.815.1.120.1.2.2.1.1	Integer32	not-accessible	Session ID.
I32 me1200RmirrorConfigSessionSourceCpuSwitchId	1.3.6.1.4.1.9.9.815.1.120.1.2.2.1.2	Integer32	not-accessible	The identification of switch.
ME1 me1200RmirrorConfigSessionSourceCpuMirrorType	1.3.6.1.4.1.9.9.815.1.120.1.2.2.1.3	ME1200RmirrorMirrorType	read-write	Mirror type on packets to/from CPU. none(0) means no mirror. tx(1) is to monitor the packets sent from CPU. rx(2) is to monitor the packets sent to CPU. both(3) is to monitor all packets sent from and to CPU. Some platforms do not support CPU mirror. Refer to CpuMirrorSupport in rmirrorCapabilities.
me1200RmirrorConfigSessionSourceVlanTable	1.3.6.1.4.1.9.9.815.1.120.1.2.3		not-accessible	This is a table of source VLAN configuration per session
me1200RmirrorConfigSessionSourceVlanEntry	1.3.6.1.4.1.9.9.815.1.120.1.2.3.1		not-accessible	Each session has a set of parameters
I32 me1200RmirrorConfigSessionSourceVlanSessionId	1.3.6.1.4.1.9.9.815.1.120.1.2.3.1.1	Integer32	not-accessible	Session ID.
NUM me1200RmirrorConfigSessionSourceVlanIfIndex	1.3.6.1.4.1.9.9.815.1.120.1.2.3.1.2	ME1200InterfaceIndex	not-accessible	Logical interface number of VLAN.
T/F me1200RmirrorConfigSessionSourceVlanMode	1.3.6.1.4.1.9.9.815.1.120.1.2.3.1.3	TruthValue	read-write	Enable/Disable monitor per VLAN. true(1) is to enable the function. false(2) is to disable it.
me1200RmirrorConfigSessionSourcePortTable	1.3.6.1.4.1.9.9.815.1.120.1.2.4		not-accessible	This is a table of source port configuration per session
me1200RmirrorConfigSessionSourcePortEntry	1.3.6.1.4.1.9.9.815.1.120.1.2.4.1		not-accessible	Each session has a set of parameters
I32 me1200RmirrorConfigSessionSourcePortSessionId	1.3.6.1.4.1.9.9.815.1.120.1.2.4.1.1	Integer32	not-accessible	Session ID.
NUM me1200RmirrorConfigSessionSourcePortIfIndex	1.3.6.1.4.1.9.9.815.1.120.1.2.4.1.2	ME1200InterfaceIndex	not-accessible	Logical interface number of physical port.
ME1 me1200RmirrorConfigSessionSourcePortMirrorType	1.3.6.1.4.1.9.9.815.1.120.1.2.4.1.3	ME1200RmirrorMirrorType	read-write	Mirror type on frames to/from port. none(0) means no mirror. tx(1) is to monitor the packets sent from the port. rx(2) is to monitor the packets sent to the port. both(3) is to monitor all packets sent from and to the port.
me1200RmirrorConfigSessionPortTable	1.3.6.1.4.1.9.9.815.1.120.1.2.5		not-accessible	This is a table of port configuration per session
me1200RmirrorConfigSessionPortEntry	1.3.6.1.4.1.9.9.815.1.120.1.2.5.1		not-accessible	Each session has a set of parameters
I32 me1200RmirrorConfigSessionPortSessionId	1.3.6.1.4.1.9.9.815.1.120.1.2.5.1.1	Integer32	not-accessible	Session ID.
NUM me1200RmirrorConfigSessionPortIfIndex	1.3.6.1.4.1.9.9.815.1.120.1.2.5.1.2	ME1200InterfaceIndex	not-accessible	Logical interface number of physical port.
ME1 me1200RmirrorConfigSessionPortType	1.3.6.1.4.1.9.9.815.1.120.1.2.5.1.3	ME1200RmirrorPortType	read-write	Type of port in rmirror function. none(0) means no mirror. intermediate(1) means the port to be a forwarding port. destination(2) means the port to be an end port. reflector(3) means the port to be a reflector port.
me1200RmirrorMibConformance	1.3.6.1.4.1.9.9.815.1.120.2
me1200RmirrorMibCompliances	1.3.6.1.4.1.9.9.815.1.120.2.1
me1200RmirrorMibCompliance	1.3.6.1.4.1.9.9.815.1.120.2.1.1			The compliance statement for the implementation.
me1200RmirrorMibGroups	1.3.6.1.4.1.9.9.815.1.120.2.2
me1200RmirrorCapabilitiesInfoGroup	1.3.6.1.4.1.9.9.815.1.120.2.2.1			A collection of objects suitable for bulk operations.
me1200RmirrorConfigSessionTableInfoGroup	1.3.6.1.4.1.9.9.815.1.120.2.2.2			A collection of objects suitable for bulk operations.
me1200RmirrorConfigSessionSourceCpuTableInfoGroup	1.3.6.1.4.1.9.9.815.1.120.2.2.3			A collection of objects suitable for bulk operations.
me1200RmirrorConfigSessionSourceVlanTableInfoGroup	1.3.6.1.4.1.9.9.815.1.120.2.2.4			A collection of objects suitable for bulk operations.
me1200RmirrorConfigSessionSourcePortTableInfoGroup	1.3.6.1.4.1.9.9.815.1.120.2.2.5			A collection of objects suitable for bulk operations.
me1200RmirrorConfigSessionPortTableInfoGroup	1.3.6.1.4.1.9.9.815.1.120.2.2.6			A collection of objects suitable for bulk operations.

RFC description

Configures port mirroring and traffic capture with reflector ports on Cisco ME1200 switches for traffic analysis.

Start monitoring Cisco ME1200 Metro Ethernet switch (remote port mirroring) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ME1200-RMIRROR-MIB

What Is ME1200-RMIRROR-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description