LUM-IFOTN-MIB

All MIBs › LUM-IFOTN-MIB

Organization: Infinera Corporation

Last Updated: 2019-04-03

Category: Optical Networking

Description: Manages Optical Transport Network (OTN) interface parameters on Infinera equipment.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is LUM-IFOTN-MIB?

This MIB, from Infinera (formerly Lumentis, hence the LUM prefix), manages Optical Transport Network (OTN) interface parameters as defined in ITU-T Recommendation G.709, covering the OTU (Optical channel Transport Unit), ODU (Optical channel Data Unit), OPU (Optical channel Payload Unit), and TP (Tributary Port) layers of the OTN framing hierarchy. It exposes general configuration and state last-change timestamps along with table-size objects for each OTN layer, letting an operator track how many OTU/ODU/OPU/TP entities are configured and when their configuration or operational state last changed. Its monitoring value is squarely in optical transport software/protocol state—detecting when OTN layer configuration or state changed (a potential indicator of a fault, reconfiguration, or link flap at the optical framing level) and confirming the expected number of provisioned optical channel entities—complementing lower-level optical hardware telemetry (power/temperature) that would live in the related LUM-IFSMTCMPM-MIB. It explicitly depends on and cross-references LUM-IFSMTCMPM-MIB for Section/Path Monitoring and Tandem Connection Monitoring detail, and is built on ITU-T G.709/G.798/G.806 standards. It would be deployed on Infinera DWDM/OTN transport platforms in service provider and long-haul optical backbone networks. Engineers can download the LUM-IFOTN-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in LUM-IFOTN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Infinera DWDM/OTN optical transport platform

Monitoring Examples

An operator would check ifOtnGeneralIfOtnOtuTableSize and ifOtnGeneralIfOtnOduTableSize to confirm the expected number of OTU and ODU entities are provisioned on a given line card, and monitor ifOtnGeneralIfOtnOtuStateLastChangeTime/ifOtnGeneralIfOtnOduStateLastChangeTime to detect recent, potentially unplanned state transitions at those layers—an early indicator of an optical link fault. ifOtnGeneralIfOtnOpuTableSize and ifOtnGeneralIfOtnTpTableSize similarly confirm payload and tributary port entity counts match provisioning expectations. A recent, unexpected update to ifOtnGeneralConfigLastChangeTime alongside a state change would prompt investigation into whether a technician or automated process altered the OTN configuration.

What Can Be Monitored

OTU/ODU/OPU/TP entity counts
OTN layer configuration last-change time
OTN layer state last-change time

Imported Objects

From LUM-REG

lumIfOtnMIB	OBJECT-IDENTITY
lumModules	OBJECT-IDENTITY

From LUM-TC

CommandString
FaultStatusWithNA
MgmtNameString
SignalStatusWithNA
TruthValueWithNA
Unsigned32WithNA

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
ifOtnGeneral	1.3.6.1.4.1.8708.2.50.2.1
DAT ifOtnGeneralConfigLastChangeTime	1.3.6.1.4.1.8708.2.50.2.1.1	DateAndTime	read-only	The time when the configuration of the MIB was last changed.
ifOtnGeneralGroupV1	1.3.6.1.4.1.8708.2.50.1.1.1			The general objects.
ifOtnGeneralGroupV2	1.3.6.1.4.1.8708.2.50.1.1.12			The general objects.
DAT ifOtnGeneralIfOtnOduConfigLastChangeTime	1.3.6.1.4.1.8708.2.50.2.1.7	DateAndTime	read-only	The time when the configuration of the table was last changed.
DAT ifOtnGeneralIfOtnOduStateLastChangeTime	1.3.6.1.4.1.8708.2.50.2.1.8	DateAndTime	read-only	The time when the state and/or configuration of the MIB was last changed.
U32 ifOtnGeneralIfOtnOduTableSize	1.3.6.1.4.1.8708.2.50.2.1.6	Unsigned32	read-only	Size of otn odu table
DAT ifOtnGeneralIfOtnOpuConfigLastChangeTime	1.3.6.1.4.1.8708.2.50.2.1.10	DateAndTime	read-only	The time when the configuration of the table was last changed.
DAT ifOtnGeneralIfOtnOpuStateLastChangeTime	1.3.6.1.4.1.8708.2.50.2.1.11	DateAndTime	read-only	The time when the state and/or configuration of the MIB was last changed.
U32 ifOtnGeneralIfOtnOpuTableSize	1.3.6.1.4.1.8708.2.50.2.1.9	Unsigned32	read-only	Size of otn opu table
DAT ifOtnGeneralIfOtnOtuConfigLastChangeTime	1.3.6.1.4.1.8708.2.50.2.1.4	DateAndTime	read-only	The time when the configuration of the table was last changed.
DAT ifOtnGeneralIfOtnOtuStateLastChangeTime	1.3.6.1.4.1.8708.2.50.2.1.5	DateAndTime	read-only	The time when the state and/or configuration of the table was last changed.
U32 ifOtnGeneralIfOtnOtuTableSize	1.3.6.1.4.1.8708.2.50.2.1.3	Unsigned32	read-only	Size of otn otu table.
DAT ifOtnGeneralIfOtnTpConfigLastChangeTime	1.3.6.1.4.1.8708.2.50.2.1.13	DateAndTime	read-only	The time when the configuration of the table was last changed.
DAT ifOtnGeneralIfOtnTpStateLastChangeTime	1.3.6.1.4.1.8708.2.50.2.1.14	DateAndTime	read-only	The time when the state and/or configuration of the MIB was last changed.
U32 ifOtnGeneralIfOtnTpTableSize	1.3.6.1.4.1.8708.2.50.2.1.12	Unsigned32	read-only	Size of otn Tp table
DAT ifOtnGeneralStateLastChangeTime	1.3.6.1.4.1.8708.2.50.2.1.2	DateAndTime	read-only	The time when the state and/or configuration of the MIB was last changed.
UNS ifOtnOduConnIfBasicIfIndex	1.3.6.1.4.1.8708.2.50.2.3.1.1.3	Unsigned32WithNA	read-create	An index that describes to which index in ifBasicIf table this object is related.
ifOtnOduEntry	1.3.6.1.4.1.8708.2.50.2.3.1.1		not-accessible	An entry in the ifOtn odu list.
TRU ifOtnOduGcc1Terminated	1.3.6.1.4.1.8708.2.50.2.3.1.1.4	TruthValueWithNA	read-only	Set if GCC1 should be terminated or not. true - GCC1 should be terminated false - GCC1 should not be terminated
TRU ifOtnOduGcc2Terminated	1.3.6.1.4.1.8708.2.50.2.3.1.1.5	TruthValueWithNA	read-only	Set if GCC2 should be terminated or not. true - GCC2 should be terminated false - GCC2 should not be terminated
ifOtnOduGroupV1	1.3.6.1.4.1.8708.2.50.1.1.3			The ifOtn odu objects (R20.0).
ifOtnOduGroupV2	1.3.6.1.4.1.8708.2.50.1.1.7			The ifOtn odu objects (R22.0).
U32 ifOtnOduIndex	1.3.6.1.4.1.8708.2.50.2.3.1.1.1	Unsigned32	read-only	An index assigned to each entry.
ifOtnOduList	1.3.6.1.4.1.8708.2.50.2.3
STR ifOtnOduName	1.3.6.1.4.1.8708.2.50.2.3.1.1.2	MgmtNameString	read-create	The management name of the otn odu, for example 'odu:1:2:1-2', where the first number indicates subrack, the second slot number and the third/fourth are the physical port numbers.
UNS ifOtnOduParentOduIndex	1.3.6.1.4.1.8708.2.50.2.3.1.1.10	Unsigned32WithNA	read-write	An index that describes to which index in ifOtnOduIf table this SubOdu object is related.
SIG ifOtnOduRxSignalStatus	1.3.6.1.4.1.8708.2.50.2.3.1.1.8	SignalStatusWithNA	read-only	The state for outgoing (RX) signal of the interface. This is reflecting the signalStatus of the OTN PM object and any terminated TCMs. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK.
ifOtnOduTable	1.3.6.1.4.1.8708.2.50.2.3.1		not-accessible	The optical channel data unit (odu) group contains information and configuration for the Odu layer objects.
SIG ifOtnOduTxSignalStatus	1.3.6.1.4.1.8708.2.50.2.3.1.1.7	SignalStatusWithNA	read-only	The state for outgoing (TX) signal of the interface. This is reflecting the signalStatus of the OTN PM object and any terminated TCMs. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK.
INT ifOtnOduType	1.3.6.1.4.1.8708.2.50.2.3.1.1.9	INTEGER	read-create	The odu type.
UNS ifOtnOduUsedTcms	1.3.6.1.4.1.8708.2.50.2.3.1.1.6	Unsigned32WithNA	read-write	This attribute indicates which ODU related TCMs that has been created. This is a bit-mask, where 0x00000000 means No TCM 0x00000001 means tcm1 0x00000010 means tcm2 ... 0x00100000 means tcm6 ... 0x00100010 means tcm2 + tcm6 ... 0x00111111 means all tcms i.e. tcm1 ..tcm6
UNS ifOtnOpuConnIfBasicIfIndex	1.3.6.1.4.1.8708.2.50.2.4.1.1.3	Unsigned32WithNA	read-only	An index that describes to which index in ifBasicIf table this object is related.
UNS ifOtnOpuConnOduIndex	1.3.6.1.4.1.8708.2.50.2.4.1.1.12	Unsigned32WithNA	read-only	An index that describes to which index in Odu table this object is related.
ifOtnOpuEntry	1.3.6.1.4.1.8708.2.50.2.4.1.1		not-accessible	An entry in the ifOtn opu list.
ifOtnOpuGroupV1	1.3.6.1.4.1.8708.2.50.1.1.4			The ifOtn opu objects (R20.0).
ifOtnOpuGroupV2	1.3.6.1.4.1.8708.2.50.1.1.6			The ifOtn opu objects (R22.0).
ifOtnOpuGroupV3	1.3.6.1.4.1.8708.2.50.1.1.9			The ifOtn opu objects (R23.1).
ifOtnOpuGroupV4	1.3.6.1.4.1.8708.2.50.1.1.13			The ifOtn opu objects (R31.0).
U32 ifOtnOpuIndex	1.3.6.1.4.1.8708.2.50.2.4.1.1.1	Unsigned32	read-only	An index assigned to each entry.
ifOtnOpuList	1.3.6.1.4.1.8708.2.50.2.4
FAU ifOtnOpuLossOfOpuMultiFrameIdentifier	1.3.6.1.4.1.8708.2.50.2.4.1.1.10	FaultStatusWithNA	read-only	Rx Loss of OPU Multi-frame identifier (LOOMFI). Monitored overhead: OPU4 Multi-Frame Identifier Direction: OPU4 Rx. If the expected 80-frame identifier goes out of expected sequence for a period of > 3 ms, LOOMFI is declared. Reference: 14.3.10.2 G.798 Values: alarm: The OPU Multi-frame identifier is lost. ok: The OPU Multi-frame identifier is present.
STR ifOtnOpuName	1.3.6.1.4.1.8708.2.50.2.4.1.1.2	MgmtNameString	read-only	The management name of the otn opu, for example 'opu:1:2:1-2', where the first number indicates subrack, the second slot number and the third/fourth are the physical port numbers.
FAU ifOtnOpuRxClientMaintenanceIndication	1.3.6.1.4.1.8708.2.50.2.4.1.1.11	FaultStatusWithNA	read-only	Rx generic alarm indication signal (generic AIS). Indicates if client maintenance signal (PN11) exists or not. alarm: A client maintenance signal is active. ok: Client maintenance signal inactive. Reference: 16.6.1 G.709/Y.1331
FAU ifOtnOpuRxPayloadMismatch	1.3.6.1.4.1.8708.2.50.2.4.1.1.8	FaultStatusWithNA	read-only	Rx Payload mismatch (PLM). Monitored overhead: OPUk-PLM Direction: Received from the associated physical interface and, unless the ODUk is terminated, the PLM is sent towards the board-internal G.805 Matrix. Reference 6.2.4.1 G.798 Values: alarm: The OPUk-PLM overhead is declared as active if the incoming payload type is not equal to the expected payload type(s). ok: The OPUk-PLM overhead is declared as inactive if the incoming payload type is equal to the expected payload type(s).
SIG ifOtnOpuRxSignalStatus	1.3.6.1.4.1.8708.2.50.2.4.1.1.5	SignalStatusWithNA	read-only	The state for incoming (RX) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK.
ifOtnOpuTable	1.3.6.1.4.1.8708.2.50.2.4.1		not-accessible	The optical channel payload unit (opu) group contains information and configuration for the Opu layer objects.
FAU ifOtnOpuTxClientMaintenanceIndication	1.3.6.1.4.1.8708.2.50.2.4.1.1.6	FaultStatusWithNA	read-only	Tx generic alarm indication signal (generic AIS). Indicates if client maintenance signal (PN11) exists or not. alarm: A client maintenance signal is active. ok: Client maintenance signal inactive. Reference: 16.6.1 G.709/Y.1331
FAU ifOtnOpuTxClientSignalFail	1.3.6.1.4.1.8708.2.50.2.4.1.1.7	FaultStatusWithNA	read-only	Tx Client signal fail (CSF). Indicates if insignal in remote end is failed or not. alarm: Remote end client is faulty. ok: Remote end client is OK. Reference: 17.1 G.709/Y.1331
FAU ifOtnOpuTxPayloadMismatch	1.3.6.1.4.1.8708.2.50.2.4.1.1.9	FaultStatusWithNA	read-only	Tx Payload mismatch (PLM). Monitored overhead: OPUk-PLM Direction: Received from the board-internal G.805 Matrix and, if applicable, sent towards the physical interface. Reference 6.2.4.1 G.798 Values: alarm: The OPUk-PLM overhead is declared as active if the incoming payload type is not equal to the expected payload type(s). ok: The OPUk-PLM overhead is declared as inactive if the incoming payload type is equal to the expected payload type(s)
SIG ifOtnOpuTxSignalStatus	1.3.6.1.4.1.8708.2.50.2.4.1.1.4	SignalStatusWithNA	read-only	The state for outgoing (TX) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK.
UNS ifOtnOtuConnIfBasicIfIndex	1.3.6.1.4.1.8708.2.50.2.2.1.1.3	Unsigned32WithNA	read-only	An index that describes to which index in ifBasicIf table this object is related.
ifOtnOtuEntry	1.3.6.1.4.1.8708.2.50.2.2.1.1		not-accessible	An entry in the ifOtn otu list.
ifOtnOtuGroupV1	1.3.6.1.4.1.8708.2.50.1.1.2			The ifOtn otu objects (R20.0).
ifOtnOtuGroupV2	1.3.6.1.4.1.8708.2.50.1.1.8			The ifOtn otu objects (R22.0).
ifOtnOtuGroupV3	1.3.6.1.4.1.8708.2.50.1.1.11			The ifOtn otu objects (R28.0).
U32 ifOtnOtuIndex	1.3.6.1.4.1.8708.2.50.2.2.1.1.1	Unsigned32	read-only	An index assigned to each entry.
ifOtnOtuList	1.3.6.1.4.1.8708.2.50.2.2
FAU ifOtnOtuLossOfFrame	1.3.6.1.4.1.8708.2.50.2.2.1.1.6	FaultStatusWithNA	read-only	Loss of frame (LOF). Reference: 6.2.5.1 G.798 alarm: An OTU frame cannot be located. ok: An OTU frame can be located.
FAU ifOtnOtuLossOfMultiframe	1.3.6.1.4.1.8708.2.50.2.2.1.1.8	FaultStatusWithNA	read-only	Loss of multiframe (LOM). Indicates loss of multiframe. Reference: 6.2.5.2 G.798 A: Loss of multiframe is active. D: Loss of multiframe inactive.
STR ifOtnOtuName	1.3.6.1.4.1.8708.2.50.2.2.1.1.2	MgmtNameString	read-only	The management name of the otn otu, for example 'otu:1:2:1-2', where the first number indicates subrack, the second slot number and the third/fourth are the physical port numbers.
FAU ifOtnOtuRxAlarmIndicationSignal	1.3.6.1.4.1.8708.2.50.2.2.1.1.7	FaultStatusWithNA	read-only	Rx Alarm indication signal (AIS). Indicates if alarm indication signal (AIS) alarm exists or not in receiving direction. Reference: 16.4 G.709, 6.2, 6.3.3 G.798 alarm: An AIS in OTU signal is detected. ok: AIS inactive.
SIG ifOtnOtuRxSignalStatus	1.3.6.1.4.1.8708.2.50.2.2.1.1.5	SignalStatusWithNA	read-only	The state for incoming (RX) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK.
ifOtnOtuTable	1.3.6.1.4.1.8708.2.50.2.2.1		not-accessible	The optical channel transport unit (otu) group contains infor- mation and configuration for the Otu layer objects.
SIG ifOtnOtuTxSignalStatus	1.3.6.1.4.1.8708.2.50.2.2.1.1.4	SignalStatusWithNA	read-only	The state for outgoing (TX) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK.
I32 ifOtnOtuUpPortId	1.3.6.1.4.1.8708.2.50.2.2.1.1.9	Integer32	read-only	Internal port reference for traffic unit.
UNS ifOtnTpConnIfBasicIfIndex	1.3.6.1.4.1.8708.2.50.2.5.1.1.3	Unsigned32WithNA	read-create	An index that describes to which index in the ifBasicIf table this object is related.
ifOtnTpEntry	1.3.6.1.4.1.8708.2.50.2.5.1.1		not-accessible	An entry in the ifOtn tp list.
ifOtnTpGroupV1	1.3.6.1.4.1.8708.2.50.1.1.5			The ifOtn tp objects (R22.0).
ifOtnTpGroupV2	1.3.6.1.4.1.8708.2.50.1.1.10			The ifOtn tp objects (R28.0).
ifOtnTpGroupV3	1.3.6.1.4.1.8708.2.50.1.1.14			The ifOtn tp objects (R33.0).
U32 ifOtnTpIndex	1.3.6.1.4.1.8708.2.50.2.5.1.1.1	Unsigned32	read-only	An index assigned to each entry.
ifOtnTpList	1.3.6.1.4.1.8708.2.50.2.5
STR ifOtnTpName	1.3.6.1.4.1.8708.2.50.2.5.1.1.2	MgmtNameString	read-create	The management name of the otn tp, for example 'tp:1:2:1', where the first number indicates subrack, the second slot number and the third is the tributary port number.
TRU ifOtnTpNotAvailableForUse	1.3.6.1.4.1.8708.2.50.2.5.1.1.12	TruthValueWithNA	read-only	The ifOtnTpTable is statically populated with entries that may or may not be available for use depending on other configuration items. This attribute states whether the tributary port object is actually possible to allocate or not. TRUE => Not possible to allocate. FALSE => Can be allocated.
FAU ifOtnTpRxMultiplexStructureIdentifierMismatch	1.3.6.1.4.1.8708.2.50.2.5.1.1.6	FaultStatusWithNA	read-only	Rx Multiplex structure identifier mismatch (MSIM). Indicates received MSI is not equal to expected MSI. alarm: The MSIM shall be declared for the ODU tributary port if the received MSI is not equal to the expected MSI. ok: MSIM shall be cleared if the received MSI is equal to the expected MSI. reference 19.4.1 G709, 6.2.9.1 G.798
SIG ifOtnTpRxSignalStatus	1.3.6.1.4.1.8708.2.50.2.5.1.1.8	SignalStatusWithNA	read-only	The state for incoming (RX) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK.
ifOtnTpTable	1.3.6.1.4.1.8708.2.50.2.5.1		not-accessible	The optical channel payload unit (tp) group contains information and configuration for the Tp layer objects.
UNS ifOtnTpTribPortId	1.3.6.1.4.1.8708.2.50.2.5.1.1.5	Unsigned32WithNA	read-create	Tributary port id.
STR ifOtnTpTribSlotMask	1.3.6.1.4.1.8708.2.50.2.5.1.1.10	DisplayString	read-write	Tributary slot mask string Format: ''
STR ifOtnTpTribSlotView	1.3.6.1.4.1.8708.2.50.2.5.1.1.11	DisplayString	read-only	Tributary slots
SIG ifOtnTpTxSignalStatus	1.3.6.1.4.1.8708.2.50.2.5.1.1.7	SignalStatusWithNA	read-only	The state for outgoing (TX) signal of the interface. down - A major fault has occurred. degraded - The signal quality is impaired. up - The signal is OK.
UNS ifOtnTpUsedTribSlots	1.3.6.1.4.1.8708.2.50.2.5.1.1.4	Unsigned32WithNA	read-only	The number of tributary slots occupied by this tributary port
UNS ifOtnTpXcRefOduIndex	1.3.6.1.4.1.8708.2.50.2.5.1.1.9	Unsigned32WithNA	read-create	An index that describes to which index in ifOtnOduIf table this TP object is contained in.
lumIfOtnCompl	1.3.6.1.4.1.8708.2.50.1.2
lumIfOtnComplV1	1.3.6.1.4.1.8708.2.50.1.2.1			Basic implementation requirements for the ifOtn MIB. (R20.0)
lumIfOtnComplV2	1.3.6.1.4.1.8708.2.50.1.2.2			Basic implementation requirements for the ifOtn MIB. (R22.0)
lumIfOtnComplV3	1.3.6.1.4.1.8708.2.50.1.2.3			Basic implementation requirements for the ifOtn MIB. (R23.1)
lumIfOtnComplV4	1.3.6.1.4.1.8708.2.50.1.2.4			Basic implementation requirements for the ifOtn MIB. (R28.0)
lumIfOtnComplV5	1.3.6.1.4.1.8708.2.50.1.2.5			Basic implementation requirements for the ifOtn MIB. (R30.0)
lumIfOtnComplV6	1.3.6.1.4.1.8708.2.50.1.2.6			Basic implementation requirements for the ifOtn MIB. (R31.0)
lumIfOtnComplV7	1.3.6.1.4.1.8708.2.50.1.2.7			Basic implementation requirements for the ifOtn MIB. (R31.0)
lumIfOtnConfs	1.3.6.1.4.1.8708.2.50.1
lumIfOtnGroups	1.3.6.1.4.1.8708.2.50.1.1
lumIfOtnMIBModule	1.3.6.1.4.1.8708.1.1.50			The MIB module for management of otn parameters on objects. Notice! The SM, TCM and PM sections are described in LUM-IFSMTCMPM-MIB.txt This module describes the otn layer in ITU-T Recommendation G.709. The references refers to the following: G.709/Y.1331 (03/2003) G.798 (06/2004) G.806 (03/2006) The tables contained in this MIB are: (1) The General group contains some general attributes as time stamps and tables sizes. (2) The optical channel transport unit (otu) group contains infor- mation and configuration for the Otu layer objects. (3) The optical channel data unit (odu) group contains information and configuration for the Odu layer objects. (4) The optical channel payload unit (opu) group contains information and configuration for the Opu layer objects. (5) The tributary port (tp) group contains information and configuration for the tributary port.
lumIfOtnMIBObjects	1.3.6.1.4.1.8708.2.50.2

RFC description

Ciena LUM (LTNM/Universal Management) vendor-private MIB for Inverse Fibre/Optical Transport Network (IFOTN) management on optical platforms.

Start monitoring Infinera DWDM/OTN optical transport platform (OTN interface parameters) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download LUM-IFOTN-MIB

What Is LUM-IFOTN-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description