LANART-AGENT

OID symbolic	OID numeric	Type	Access	Description
at	1.3.6.1.2.1.3
atEntry	1.3.6.1.2.1.3.1.1		not-accessible	Each entry contains one NetworkAddress to `physical' address equivalence.
INT atIfIndex	1.3.6.1.2.1.3.1.1.1	INTEGER	read-write	The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
IP atNetAddress	1.3.6.1.2.1.3.1.1.3	IpAddress	read-write	The NetworkAddress (e.g., the IP address) corresponding to the media-dependent `physical' address.
PHY atPhysAddress	1.3.6.1.2.1.3.1.1.2	PhysAddress	read-write	The media-dependent `physical' address. Setting this object to a null string (one of zero length) has the effect of invaliding the corresponding entry in the atTable object. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant atPhysAddress object.
atTable	1.3.6.1.2.1.3.1		not-accessible	The Address Translation tables contain the NetworkAddress to `physical' address equivalences. Some interfaces do not use translation tables for determining address equivalences (e.g., DDN-X.25 has an algorithmic method); if all interfaces are of this type, then the Address Translation table is empty, i.e., has zero entries.
bbAui	1.3.6.1.4.1.712.1.1.1.3.0
bbAui10BASE_FL	1.3.6.1.4.1.712.1.1.1.3.4
bbAuiBnc	1.3.6.1.4.1.712.1.1.1.3.2
bbAuiTp	1.3.6.1.4.1.712.1.1.1.3.1
bbAuiTpBnc	1.3.6.1.4.1.712.1.1.1.3.3
ccitt	0
directory	1.3.6.1.1
dod	1.3.6
dot1dBase	1.3.6.1.2.1.17.1
dot1dBridge	1.3.6.1.2.1.17
dot1dSr	1.3.6.1.2.1.17.3
dot1dStatic	1.3.6.1.2.1.17.5
dot1dStp	1.3.6.1.2.1.17.2
dot1dTp	1.3.6.1.2.1.17.4
egp	1.3.6.1.2.1.8
enterprises	1.3.6.1.4.1
ete120x	1.3.6.1.4.1.712.1.1.1.2.12
ete160x	1.3.6.1.4.1.712.1.1.1.2.16
ete240x	1.3.6.1.4.1.712.1.1.1.2.24
etm120x	1.3.6.1.4.1.712.1.1.1.1.12
etm160x	1.3.6.1.4.1.712.1.1.1.1.16
etm240x	1.3.6.1.4.1.712.1.1.1.1.24
experimental	1.3.6.1.3
icmp	1.3.6.1.2.1.5
CTR icmpInAddrMaskReps	1.3.6.1.2.1.5.13	Counter	read-only	The number of ICMP Address Mask Reply messages received.
CTR icmpInAddrMasks	1.3.6.1.2.1.5.12	Counter	read-only	The number of ICMP Address Mask Request messages received.
CTR icmpInDestUnreachs	1.3.6.1.2.1.5.3	Counter	read-only	The number of ICMP Destination Unreachable messages received.
CTR icmpInEchoReps	1.3.6.1.2.1.5.9	Counter	read-only	The number of ICMP Echo Reply messages received.
CTR icmpInEchos	1.3.6.1.2.1.5.8	Counter	read-only	The number of ICMP Echo (request) messages received.
CTR icmpInErrors	1.3.6.1.2.1.5.2	Counter	read-only	The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.).
CTR icmpInMsgs	1.3.6.1.2.1.5.1	Counter	read-only	The total number of ICMP messages which the entity received. Note that this counter includes all those counted by icmpInErrors.
CTR icmpInParmProbs	1.3.6.1.2.1.5.5	Counter	read-only	The number of ICMP Parameter Problem messages received.
CTR icmpInRedirects	1.3.6.1.2.1.5.7	Counter	read-only	The number of ICMP Redirect messages received.
CTR icmpInSrcQuenchs	1.3.6.1.2.1.5.6	Counter	read-only	The number of ICMP Source Quench messages received.
CTR icmpInTimeExcds	1.3.6.1.2.1.5.4	Counter	read-only	The number of ICMP Time Exceeded messages received.
CTR icmpInTimestampReps	1.3.6.1.2.1.5.11	Counter	read-only	The number of ICMP Timestamp Reply messages received.
CTR icmpInTimestamps	1.3.6.1.2.1.5.10	Counter	read-only	The number of ICMP Timestamp (request) messages received.
CTR icmpOutAddrMaskReps	1.3.6.1.2.1.5.26	Counter	read-only	The number of ICMP Address Mask Reply messages sent.
CTR icmpOutAddrMasks	1.3.6.1.2.1.5.25	Counter	read-only	The number of ICMP Address Mask Request messages sent.
CTR icmpOutDestUnreachs	1.3.6.1.2.1.5.16	Counter	read-only	The number of ICMP Destination Unreachable messages sent.
CTR icmpOutEchoReps	1.3.6.1.2.1.5.22	Counter	read-only	The number of ICMP Echo Reply messages sent.
CTR icmpOutEchos	1.3.6.1.2.1.5.21	Counter	read-only	The number of ICMP Echo (request) messages sent.
CTR icmpOutErrors	1.3.6.1.2.1.5.15	Counter	read-only	The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there may be no types of error which contribute to this counter's value.
CTR icmpOutMsgs	1.3.6.1.2.1.5.14	Counter	read-only	The total number of ICMP messages which this entity attempted to send. Note that this counter includes all those counted by icmpOutErrors.
CTR icmpOutParmProbs	1.3.6.1.2.1.5.18	Counter	read-only	The number of ICMP Parameter Problem messages sent.
CTR icmpOutRedirects	1.3.6.1.2.1.5.20	Counter	read-only	The number of ICMP Redirect messages sent. For a host, this object will always be zero, since hosts do not send redirects.
CTR icmpOutSrcQuenchs	1.3.6.1.2.1.5.19	Counter	read-only	The number of ICMP Source Quench messages sent.
CTR icmpOutTimeExcds	1.3.6.1.2.1.5.17	Counter	read-only	The number of ICMP Time Exceeded messages sent.
CTR icmpOutTimestampReps	1.3.6.1.2.1.5.24	Counter	read-only	The number of ICMP Timestamp Reply messages sent.
CTR icmpOutTimestamps	1.3.6.1.2.1.5.23	Counter	read-only	The number of ICMP Timestamp (request) messages sent.
INT ifAdminStatus	1.3.6.1.2.1.2.2.1.7	INTEGER	read-write	The desired state of the interface. The testing(3) state indicates that no operational packets can be passed.
STR ifDescr	1.3.6.1.2.1.2.2.1.2	DisplayString	read-only	A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the hardware interface.
ifEntry	1.3.6.1.2.1.2.2.1		not-accessible	An interface entry containing objects at the subnetwork layer and below for a particular interface.
INT ifIndex	1.3.6.1.2.1.2.2.1.1	INTEGER	read-only	A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.
CTR ifInDiscards	1.3.6.1.2.1.2.2.1.13	Counter	read-only	The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.
CTR ifInErrors	1.3.6.1.2.1.2.2.1.14	Counter	read-only	The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol.
CTR ifInNUcastPkts	1.3.6.1.2.1.2.2.1.12	Counter	read-only	The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol.
CTR ifInOctets	1.3.6.1.2.1.2.2.1.10	Counter	read-only	The total number of octets received on the interface, including framing characters.
CTR ifInUcastPkts	1.3.6.1.2.1.2.2.1.11	Counter	read-only	The number of subnetwork-unicast packets delivered to a higher-layer protocol.
CTR ifInUnknownProtos	1.3.6.1.2.1.2.2.1.15	Counter	read-only	The number of packets received via the interface which were discarded because of an unknown or unsupported protocol.
TIK ifLastChange	1.3.6.1.2.1.2.2.1.9	TimeTicks	read-only	The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.
INT ifMtu	1.3.6.1.2.1.2.2.1.4	INTEGER	read-only	The size of the largest datagram which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface.
INT ifNumber	1.3.6.1.2.1.2.1	INTEGER	read-only	The number of network interfaces (regardless of their current state) present on this system.
INT ifOperStatus	1.3.6.1.2.1.2.2.1.8	INTEGER	read-only	The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed.
CTR ifOutDiscards	1.3.6.1.2.1.2.2.1.19	Counter	read-only	The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.
CTR ifOutErrors	1.3.6.1.2.1.2.2.1.20	Counter	read-only	The number of outbound packets that could not be transmitted because of errors.
CTR ifOutNUcastPkts	1.3.6.1.2.1.2.2.1.18	Counter	read-only	The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent.
CTR ifOutOctets	1.3.6.1.2.1.2.2.1.16	Counter	read-only	The total number of octets transmitted out of the interface, including framing characters.
GAU ifOutQLen	1.3.6.1.2.1.2.2.1.21	Gauge	read-only	The length of the output packet queue (in packets).
CTR ifOutUcastPkts	1.3.6.1.2.1.2.2.1.17	Counter	read-only	The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.
PHY ifPhysAddress	1.3.6.1.2.1.2.2.1.6	PhysAddress	read-only	The interface's address at the protocol layer immediately `below' the network layer in the protocol stack. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length.
OID ifSpecific	1.3.6.1.2.1.2.2.1.22	OBJECT IDENTIFIER	read-only	A reference to MIB definitions specific to the particular media being used to realize the interface. For example, if the interface is realized by an ethernet, then the value of this object refers to a document defining objects specific to ethernet. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value.
GAU ifSpeed	1.3.6.1.2.1.2.2.1.5	Gauge	read-only	An estimate of the interface's current bandwidth in bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth.
ifTable	1.3.6.1.2.1.2.2		not-accessible	A list of interface entries. The number of entries is given by the value of ifNumber.
INT ifType	1.3.6.1.2.1.2.2.1.3	INTEGER	read-only	The type of interface, distinguished according to the physical/link protocol(s) immediately `below' the network layer in the protocol stack.
interfaces	1.3.6.1.2.1.2
internet	1.3.6.1
ip	1.3.6.1.2.1.4
ipAddrEntry	1.3.6.1.2.1.4.20.1		not-accessible	The addressing information for one of this entity's IP addresses.
ipAddrTable	1.3.6.1.2.1.4.20		not-accessible	The table of addressing information relevant to this entity's IP addresses.
IP ipAdEntAddr	1.3.6.1.2.1.4.20.1.1	IpAddress	read-only	The IP address to which this entry's addressing information pertains.
INT ipAdEntBcastAddr	1.3.6.1.2.1.4.20.1.4	INTEGER	read-only	The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface.
INT ipAdEntIfIndex	1.3.6.1.2.1.4.20.1.2	INTEGER	read-only	The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
IP ipAdEntNetMask	1.3.6.1.2.1.4.20.1.3	IpAddress	read-only	The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.
INT ipAdEntReasmMaxSize	1.3.6.1.2.1.4.20.1.5	INTEGER	read-only	The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface.
INT ipDefaultTTL	1.3.6.1.2.1.4.2	INTEGER	read-write	The default value inserted into the Time-To-Live field of the IP header of datagrams originated at this entity, whenever a TTL value is not supplied by the transport layer protocol.
INT ipForwarding	1.3.6.1.2.1.4.1	INTEGER	read-write	The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to change this object to an inappropriate value.
CTR ipForwDatagrams	1.3.6.1.2.1.4.6	Counter	read-only	The number of input datagrams for which this entity was not their final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as IP Gateways, this counter will include only those packets which were Source-Routed via this entity, and the Source- Route option processing was successful.
CTR ipFragCreates	1.3.6.1.2.1.4.19	Counter	read-only	The number of IP datagram fragments that have been generated as a result of fragmentation at this entity.
CTR ipFragFails	1.3.6.1.2.1.4.18	Counter	read-only	The number of IP datagrams that have been discarded because they needed to be fragmented at this entity but could not be, e.g., because their Don't Fragment flag was set.
CTR ipFragOKs	1.3.6.1.2.1.4.17	Counter	read-only	The number of IP datagrams that have been successfully fragmented at this entity.
CTR ipInAddrErrors	1.3.6.1.2.1.4.5	Counter	read-only	The number of input datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., 0.0.0.0) and addresses of unsupported Classes (e.g., Class E). For entities which are not IP Gateways and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address.
CTR ipInDelivers	1.3.6.1.2.1.4.9	Counter	read-only	The total number of input datagrams successfully delivered to IP user-protocols (including ICMP).
CTR ipInDiscards	1.3.6.1.2.1.4.8	Counter	read-only	The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly.
CTR ipInHdrErrors	1.3.6.1.2.1.4.4	Counter	read-only	The number of input datagrams discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IP options, etc.
CTR ipInReceives	1.3.6.1.2.1.4.3	Counter	read-only	The total number of input datagrams received from interfaces, including those received in error.
CTR ipInUnknownProtos	1.3.6.1.2.1.4.7	Counter	read-only	The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol.
ipNetToMediaEntry	1.3.6.1.2.1.4.22.1		not-accessible	Each entry contains one IpAddress to `physical' address equivalence.
INT ipNetToMediaIfIndex	1.3.6.1.2.1.4.22.1.1	INTEGER	read-write	The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
IP ipNetToMediaNetAddress	1.3.6.1.2.1.4.22.1.3	IpAddress	read-only	The IpAddress corresponding to the media- dependent `physical' address.
PHY ipNetToMediaPhysAddress	1.3.6.1.2.1.4.22.1.2	PhysAddress	read-write	The media-dependent `physical' address.
ipNetToMediaTable	1.3.6.1.2.1.4.22		not-accessible	The IP Address Translation table used for mapping from IP addresses to physical addresses.
INT ipNetToMediaType	1.3.6.1.2.1.4.22.1.4	INTEGER	read-write	The type of mapping. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipNetToMediaTable. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipNetToMediaType object.
CTR ipOutDiscards	1.3.6.1.2.1.4.11	Counter	read-only	The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in ipForwDatagrams if any such packets met this (discretionary) discard criterion.
CTR ipOutNoRoutes	1.3.6.1.2.1.4.12	Counter	read-only	The number of IP datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets counted in ipForwDatagrams which meet this `no-route' criterion. Note that this includes any datagarms which a host cannot route because all of its default gateways are down.
CTR ipOutRequests	1.3.6.1.2.1.4.10	Counter	read-only	The total number of IP datagrams which local IP user-protocols (including ICMP) supplied to IP in requests for transmission. Note that this counter does not include any datagrams counted in ipForwDatagrams.
CTR ipReasmFails	1.3.6.1.2.1.4.16	Counter	read-only	The number of failures detected by the IP re- assembly algorithm (for whatever reason: timed out, errors, etc). Note that this is not necessarily a count of discarded IP fragments since some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments by combining them as they are received.
CTR ipReasmOKs	1.3.6.1.2.1.4.15	Counter	read-only	The number of IP datagrams successfully re- assembled.
CTR ipReasmReqds	1.3.6.1.2.1.4.14	Counter	read-only	The number of IP fragments received which needed to be reassembled at this entity.
INT ipReasmTimeout	1.3.6.1.2.1.4.13	INTEGER	read-only	The maximum number of seconds which received fragments are held while they are awaiting reassembly at this entity.
INT ipRouteAge	1.3.6.1.2.1.4.21.1.10	INTEGER	read-write	The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned.
IP ipRouteDest	1.3.6.1.2.1.4.21.1.1	IpAddress	read-write	The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.
ipRouteEntry	1.3.6.1.2.1.4.21.1		not-accessible	A route to a particular destination.
INT ipRouteIfIndex	1.3.6.1.2.1.4.21.1.2	INTEGER	read-write	The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.
OID ipRouteInfo	1.3.6.1.2.1.4.21.1.13	OBJECT IDENTIFIER	read-only	A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's ipRouteProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value.
IP ipRouteMask	1.3.6.1.2.1.4.21.1.11	IpAddress	read-write	Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipRouteMask by determining whether the value of the correspondent ipRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the ipRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.
INT ipRouteMetric1	1.3.6.1.2.1.4.21.1.3	INTEGER	read-write	The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
INT ipRouteMetric2	1.3.6.1.2.1.4.21.1.4	INTEGER	read-write	An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
INT ipRouteMetric3	1.3.6.1.2.1.4.21.1.5	INTEGER	read-write	An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
INT ipRouteMetric4	1.3.6.1.2.1.4.21.1.6	INTEGER	read-write	An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
INT ipRouteMetric5	1.3.6.1.2.1.4.21.1.12	INTEGER	read-write	An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.
IP ipRouteNextHop	1.3.6.1.2.1.4.21.1.7	IpAddress	read-write	The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.)
INT ipRouteProto	1.3.6.1.2.1.4.21.1.9	INTEGER	read-only	The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.
ipRouteTable	1.3.6.1.2.1.4.21		not-accessible	This entity's IP Routing table.
INT ipRouteType	1.3.6.1.2.1.4.21.1.8	INTEGER	read-write	The type of route. Note that the values direct(3) and indirect(4) refer to the notion of direct and indirect routing in the IP architecture. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipRouteType object.
CTR ipRoutingDiscards	1.3.6.1.2.1.4.23	Counter	read-only	The number of routing entries which were chosen to be discarded even though they are valid. One possible reason for discarding such an entry could be to free-up buffer space for other routing entries.
iso	1
laHubMib	1.3.6.1.4.1.712.1.2
INT laJoystick	1.3.6.1.4.1.712.1.2.1.2	INTEGER	read-write	Setting this object to disabled(2) prevents use of the four-position switch on the front panel. Resetting this object to enabled(1) allows use of the switch.
INT laLinkAlert	1.3.6.1.4.1.712.1.2.1.3	INTEGER	read-write	Setting this object enables or disables the LinkALERT feature of the backbone 10BASE-T or 10BASE-FL port. A return value of not-applicable indicates that none of the backbone ports feature LinkALERT.
laMib1	1.3.6.1.4.1.712.1
lanart	1.3.6.1.4.1.712
laProducts	1.3.6.1.4.1.712.1.1
laSys	1.3.6.1.4.1.712.1.2.1
INT laSysConfig	1.3.6.1.4.1.712.1.2.1.1	INTEGER	read-write	Setting this object to save(1) will save all configuration variables to non-volatile memory. Setting this object to load(2) will configure the hub according to the stored configuration. Setting this object to factory(3) will configure the hub according to the factory settings. A return value of ok(4) means the non-volatile memory is operational. A return value of failed(5) means the non-volatile memory has failed.
INT laTpAutoPolarity	1.3.6.1.4.1.712.1.2.2.1.1.4	INTEGER	read-write	Setting this object to disabled(2) disables the auto polarity test for this port. Setting this object to enabled(1) enables the feature. A return value of corrected(3) indicates that the polarity test has sensed a reversal on the receive wiring pair, and has corrected this fault by inverting its receive signal. A return value of not-applicable(4) indicates that the specified port does not support polarity correction.
laTpHub	1.3.6.1.4.1.712.1.1.1
laTpHub1	1.3.6.1.4.1.712.1.1.1.1
laTpHub2	1.3.6.1.4.1.712.1.1.1.2
laTpHub3	1.3.6.1.4.1.712.1.1.1.3
INT laTpLinkTest	1.3.6.1.4.1.712.1.2.2.1.1.3	INTEGER	read-write	Setting this object to disabled(2) disables the link test feature. This may be useful for interoperation with pre-10BASE-T equipment. Setting this object to enabled(1) enables the feature. A return value of failed(3) indicates a link test failure for this port. A return value of not-applicable(4) indicates that the specified port does not have a link test.
laTpPort	1.3.6.1.4.1.712.1.2.2
laTpPortEntry	1.3.6.1.4.1.712.1.2.2.1.1		not-accessible	An entry in the table, containing information about a single port.
INT laTpPortGroupIndex	1.3.6.1.4.1.712.1.2.2.1.1.1	INTEGER	read-only	This object identifies the group containing the port for which this entry contains information.
INT laTpPortIndex	1.3.6.1.4.1.712.1.2.2.1.1.2	INTEGER	read-only	This object identifies the port within the group for which this entry contains information.
laTpPortTable	1.3.6.1.4.1.712.1.2.2.1		not-accessible	Table of descriptive and status information about the ports.
mgmt	1.3.6.1.2
mib_2	1.3.6.1.2.1
NTF newRoot	1.3.6.1.2.1.17.0.1			The newRoot trap indicates that the sending agent has become the new root of the Spanning Tree; the trap is sent by a bridge soon after its election as the new root, e.g., upon expiration of the Topology Change Timer immediately subsequent to its election.
null	0.0
org	1.3
private	1.3.6.1.4
rptrAddrTrackEntry	1.3.6.1.2.1.22.3.3.1.1		not-accessible	An entry in the table, containing address mapping information about a single port.
INT rptrAddrTrackGroupIndex	1.3.6.1.2.1.22.3.3.1.1.1	INTEGER	read-only	This object identifies the group containing the port for which this entry contains information.
rptrAddrTrackGroupInfo	1.3.6.1.2.1.22.3.2
MAC rptrAddrTrackLastSourceAddress	1.3.6.1.2.1.22.3.3.1.1.3	MacAddress	read-only	This object is the SourceAddress of the last readable frame (i.e., counted by rptrMonitorPortReadableFrames) received by this port.
rptrAddrTrackPackage	1.3.6.1.2.1.22.3
INT rptrAddrTrackPortIndex	1.3.6.1.2.1.22.3.3.1.1.2	INTEGER	read-only	This object identifies the port within the group for which this entry contains information.
rptrAddrTrackPortInfo	1.3.6.1.2.1.22.3.3
rptrAddrTrackRptrInfo	1.3.6.1.2.1.22.3.1
CTR rptrAddrTrackSourceAddrChanges	1.3.6.1.2.1.22.3.3.1.1.4	Counter	read-only	This counter is incremented by one for each time that the rptrAddrTrackLastSourceAddress attribute for this port has changed. This may indicate whether a link is connected to a single DTE or another multi-user segment. The approximate minimum time for rollover of this counter is 81 hours.
rptrAddrTrackTable	1.3.6.1.2.1.22.3.3.1		not-accessible	Table of address mapping information about the ports.
rptrBasicPackage	1.3.6.1.2.1.22.1
INT rptrGroupCapacity	1.3.6.1.2.1.22.1.1.1	INTEGER	read-only	The rptrGroupCapacity is the number of groups that can be contained within the repeater. Within each managed repeater, the groups are uniquely numbered in the range from 1 to rptrGroupCapacity. Some groups may not be present in the repeater, in which case the actual number of groups present will be less than rptrGroupCapacity. The number of groups present will never be greater than rptrGroupCapacity. Note: In practice, this will generally be the number of field-replaceable units (i.e., modules, cards, or boards) that can fit in the physical repeater enclosure, and the group numbers will correspond to numbers marked on the physical enclosure.
NTF rptrGroupChange	1.3.6.1.2.1.22.0.2			This trap is sent when a change occurs in the group structure of a repeater. This occurs only when a group is logically or physically removed from or added to a repeater. The varBind list contains the identifier of the group that was removed or added. The agent must throttle the generation of consecutive rptrGroupChange traps for the same group so that there is at least a five-second gap between them.
STR rptrGroupDescr	1.3.6.1.2.1.22.1.2.1.1.2	DisplayString	read-only	A textual description of the group. This value should include the full name and version identification of the group's hardware type and indicate how the group is differentiated from other groups in the repeater. Plug-in Module, Rev A' or 'Barney Rubble 10BASE-T 4-port SIMM socket Version 2.1' are examples of valid group descriptions. It is mandatory that this only contain printable ASCII characters.
rptrGroupEntry	1.3.6.1.2.1.22.1.2.1.1		not-accessible	An entry in the table, containing information about a single group of ports.
INT rptrGroupIndex	1.3.6.1.2.1.22.1.2.1.1.1	INTEGER	read-only	This object identifies the group within the repeater for which this entry contains information. This value is never greater than rptrGroupCapacity.
rptrGroupInfo	1.3.6.1.2.1.22.1.2
TIK rptrGroupLastOperStatusChange	1.3.6.1.2.1.22.1.2.1.1.5	TimeTicks	read-only	An object that contains the value of sysUpTime at the time that the value of the rptrGroupOperStatus object for this group last changed. A value of zero indicates that the group's oper status has not changed since the agent last restarted.
OID rptrGroupObjectID	1.3.6.1.2.1.22.1.2.1.1.3	OBJECT IDENTIFIER	read-only	The vendor's authoritative identification of the group. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides a straight-forward and unambiguous means for determining what kind of group is being managed. For example, this object could take the value 1.3.6.1.4.1.4242.1.2.14 if vendor 'Flintstones, Inc.' was assigned the subtree 1.3.6.1.4.1.4242, and had assigned the identifier 1.3.6.1.4.1.4242.1.2.14 to its 'Wilma Flintstone 6-Port FOIRL Plug-in Module.'
INT rptrGroupOperStatus	1.3.6.1.2.1.22.1.2.1.1.4	INTEGER	read-only	An object that indicates the operational status of the group. A status of notPresent(4) indicates that the group is temporarily or permanently physically and/or logically not a part of the repeater. It is an implementation-specific matter as to whether the agent effectively removes notPresent entries from the table. A status of operational(2) indicates that the group is functioning, and a status of malfunctioning(3) indicates that the group is malfunctioning in some way.
INT rptrGroupPortCapacity	1.3.6.1.2.1.22.1.2.1.1.6	INTEGER	read-only	The rptrGroupPortCapacity is the number of ports that can be contained within the group. Valid range is 1-1024. Within each group, the ports are uniquely numbered in the range from 1 to rptrGroupPortCapacity. Note: In practice, this will generally be the number of ports on a module, card, or board, and the port numbers will correspond to numbers marked on the physical embodiment.
rptrGroupTable	1.3.6.1.2.1.22.1.2.1		not-accessible	Table of descriptive and status information about the groups of ports.
NTF rptrHealth	1.3.6.1.2.1.22.0.1			The rptrHealth trap conveys information related to the operational status of the repeater. This trap is sent only when the oper status of the repeater changes. The rptrHealth trap must contain the rptrOperStatus object. The agent may optionally include the rptrHealthText object in the varBind list. See the rptrOperStatus and rptrHealthText objects for descriptions of the information that is sent. The agent must throttle the generation of consecutive rptrHealth traps so that there is at least a five-second gap between them.
STR rptrHealthText	1.3.6.1.2.1.22.1.1.3	DisplayString	read-only	The health text object is a text string that provides information relevant to the operational state of the repeater. Agents may use this string to provide detailed information on current failures, including how they were detected, and/or instructions for problem resolution. The contents are agent-specific.
rptrMonitorGroupEntry	1.3.6.1.2.1.22.2.2.1.1		not-accessible	An entry in the table, containing total performance and error statistics for a single group. Regular retrieval of the information in this table provides a means of tracking the performance and health of the networked devices attached to this group's ports. The counters in this table are redundant in the sense that they are the summations of information already available through other objects. However, these sums provide a considerable optimization of network management traffic over the otherwise necessary retrieval of the individual counters included in each sum.
INT rptrMonitorGroupIndex	1.3.6.1.2.1.22.2.2.1.1.1	INTEGER	read-only	This object identifies the group within the repeater for which this entry contains information.
rptrMonitorGroupInfo	1.3.6.1.2.1.22.2.2
rptrMonitorGroupTable	1.3.6.1.2.1.22.2.2.1		not-accessible	Table of performance and error statistics for the groups.
CTR rptrMonitorGroupTotalErrors	1.3.6.1.2.1.22.2.2.1.1.4	Counter	read-only	The total number of errors which have occurred on all of the ports in this group. This counter is the summation of the values of the rptrMonitorPortTotalErrors counters for all of the ports in the group.
CTR rptrMonitorGroupTotalFrames	1.3.6.1.2.1.22.2.2.1.1.2	Counter	read-only	The total number of frames of valid frame length that have been received on the ports in this group. This counter is the summation of the values of the rptrMonitorPortReadableFrames counters for all of the ports in the group. This statistic provides one of the parameters necessary for obtaining the packet error rate. The approximate minimum time for rollover of this counter is 80 hours.
CTR rptrMonitorGroupTotalOctets	1.3.6.1.2.1.22.2.2.1.1.3	Counter	read-only	The total number of octets contained in the valid frames that have been received on the ports in this group. This counter is the summation of the values of the rptrMonitorPortReadableOctets counters for all of the ports in the group. This statistic provides an indicator of the total data transferred. The approximate minimum time for rollover of this counter is 58 minutes.
rptrMonitorPackage	1.3.6.1.2.1.22.2
CTR rptrMonitorPortAlignmentErrors	1.3.6.1.2.1.22.2.3.1.1.6	Counter	read-only	This counter is incremented by one for each frame received on this port with the FCSError and FramingError signals asserted and CollisionEvent signal deasserted and whose OctetCount is greater than or equal to minFrameSize and less than or equal to maxFrameSize (Ref: IEEE 802.3 Std, 4.4.2.1). If rptrMonitorPortAlignmentErrors is incremented then the rptrMonitorPortFCSErrors Counter shall not be incremented for the same frame. The approximate minimum time for rollover of this counter is 80 hours.
CTR rptrMonitorPortAutoPartitions	1.3.6.1.2.1.22.2.3.1.1.14	Counter	read-only	This counter is incremented by one for each time the repeater has automatically partitioned this port. The conditions that cause port partitioning are specified in the partition state machine in Section 9 [IEEE 802.3 Std]. They are not differentiated here.
CTR rptrMonitorPortCollisions	1.3.6.1.2.1.22.2.3.1.1.10	Counter	read-only	This counter is incremented by one for any CarrierEvent signal on any port for which the CollisionEvent signal on this port is asserted. The approximate minimum time for rollover of this counter is 16 hours.
CTR rptrMonitorPortDataRateMismatches	1.3.6.1.2.1.22.2.3.1.1.13	Counter	read-only	This counter is incremented by one for each frame received on this port that meets all of the following conditions: a) The CollisionEvent signal is not asserted. b) The ActivityDuration is greater than ValidPacketMinTime. c) The frequency (data rate) is detectably mismatched from the local transmit frequency. The exact degree of mismatch is vendor specific and is to be defined by the vendor for conformance testing. When this event occurs, other counters whose increment conditions were satisfied may or may not also be incremented, at the implementor's discretion. Whether or not the repeater was able to maintain data integrity is beyond the scope of this standard.
rptrMonitorPortEntry	1.3.6.1.2.1.22.2.3.1.1		not-accessible	An entry in the table, containing performance and error statistics for a single port.
CTR rptrMonitorPortFCSErrors	1.3.6.1.2.1.22.2.3.1.1.5	Counter	read-only	This counter is incremented by one for each frame received on this port with the FCSError signal asserted and the FramingError and CollisionEvent signals deasserted and whose OctetCount is greater than or equal to minFrameSize and less than or equal to maxFrameSize (Ref: 4.4.2.1, IEEE 802.3 Std). The approximate minimum time for rollover of this counter is 80 hours.
CTR rptrMonitorPortFrameTooLongs	1.3.6.1.2.1.22.2.3.1.1.7	Counter	read-only	This counter is incremented by one for each frame received on this port whose OctetCount is greater than maxFrameSize (Ref: 4.4.2.1, IEEE 802.3 Std). If rptrMonitorPortFrameTooLongs is incremented then neither the rptrMonitorPortAlignmentErrors nor the rptrMonitorPortFCSErrors counter shall be incremented for the frame. The approximate minimum time for rollover of this counter is 61 days.
INT rptrMonitorPortGroupIndex	1.3.6.1.2.1.22.2.3.1.1.1	INTEGER	read-only	This object identifies the group containing the port for which this entry contains information.
INT rptrMonitorPortIndex	1.3.6.1.2.1.22.2.3.1.1.2	INTEGER	read-only	This object identifies the port within the group for which this entry contains information.
rptrMonitorPortInfo	1.3.6.1.2.1.22.2.3
CTR rptrMonitorPortLateEvents	1.3.6.1.2.1.22.2.3.1.1.11	Counter	read-only	This counter is incremented by one for each CarrierEvent on this port in which the CollIn(X) variable transitions to the value SQE (Ref: 9.6.6.2, IEEE 802.3 Std) while the ActivityDuration is greater than the LateEventThreshold. Such a CarrierEvent is counted twice, as both a collision and as a lateEvent. The LateEventThreshold is greater than 480 bit times and less than 565 bit times. LateEventThreshold has tolerances included to permit an implementation to build a single threshold to serve as both the LateEventThreshold and ValidPacketMinTime threshold. The approximate minimum time for rollover of this counter is 81 hours.
CTR rptrMonitorPortReadableFrames	1.3.6.1.2.1.22.2.3.1.1.3	Counter	read-only	This object is the number of frames of valid frame length that have been received on this port. This counter is incremented by one for each frame received on this port whose OctetCount is greater than or equal to minFrameSize and less than or equal to maxFrameSize (Ref: IEEE 802.3 Std, 4.4.2.1) and for which the FCSError and CollisionEvent signals are not asserted. This statistic provides one of the parameters necessary for obtaining the packet error rate. The approximate minimum time for rollover of this counter is 80 hours.
CTR rptrMonitorPortReadableOctets	1.3.6.1.2.1.22.2.3.1.1.4	Counter	read-only	This object is the number of octets contained in valid frames that have been received on this port. This counter is incremented by OctetCount for each frame received on this port which has been determined to be a readable frame. This statistic provides an indicator of the total data transferred. The approximate minimum time for rollover of this counter is 58 minutes.
CTR rptrMonitorPortRunts	1.3.6.1.2.1.22.2.3.1.1.9	Counter	read-only	This counter is incremented by one for each CarrierEvent on this port that meets one of the following two conditions. Only one test need be made. a) The ActivityDuration is greater than ShortEventMaxTime and less than ValidPacketMinTime and the CollisionEvent signal is deasserted. b) The OctetCount is less than 64, the ActivityDuration is greater than ShortEventMaxTime and the CollisionEvent signal is deasserted. ValidPacketMinTime is greater than or equal to 552 bit times and less than 565 bit times. An event whose length is greater than 74 bit times but less than 82 bit times shall increment either the shortEvents counter or the runts counter but not both. A CarrierEvent greater than or equal to 552 bit times but less than 565 bit times may or may not be counted as a runt. ValidPacketMinTime has tolerances included to provide for circuit losses between a conformance test point at the AUI and the measurement point within the state machine. Runts usually indicate collision fragments, a normal network event. In certain situations associated with large diameter networks a percentage of runts may exceed ValidPacketMinTime. The approximate minimum time for rollover of this counter is 16 hours.
CTR rptrMonitorPortShortEvents	1.3.6.1.2.1.22.2.3.1.1.8	Counter	read-only	This counter is incremented by one for each CarrierEvent on this port with ActivityDuration less than ShortEventMaxTime. ShortEventMaxTime is greater than 74 bit times and less than 82 bit times. ShortEventMaxTime has tolerances included to provide for circuit losses between a conformance test point at the AUI and the measurement point within the state machine. Note: shortEvents may indicate externally generated noise hits which will cause the repeater to transmit Runts to its other ports, or propagate a collision (which may be late) back to the transmitting DTE and damaged frames to the rest of the network. Implementors may wish to consider selecting the ShortEventMaxTime towards the lower end of the allowed tolerance range to accommodate bit losses suffered through physical channel devices not budgeted for within this standard. The approximate minimum time for rollover of this counter is 16 hours.
rptrMonitorPortTable	1.3.6.1.2.1.22.2.3.1		not-accessible	Table of performance and error statistics for the ports.
CTR rptrMonitorPortTotalErrors	1.3.6.1.2.1.22.2.3.1.1.15	Counter	read-only	The total number of errors which have occurred on this port. This counter is the summation of the values of other error counters (for the same port), namely: rptrMonitorPortFCSErrors, rptrMonitorPortAlignmentErrors, rptrMonitorPortFrameTooLongs, rptrMonitorPortShortEvents, rptrMonitorPortLateEvents, rptrMonitorPortVeryLongEvents, and rptrMonitorPortDataRateMismatches. This counter is redundant in the sense that it is the summation of information already available through other objects. However, it is included specifically because the regular retrieval of this object as a means of tracking the health of a port provides a considerable optimization of network management traffic over the otherwise necessary retrieval of the summed counters.
CTR rptrMonitorPortVeryLongEvents	1.3.6.1.2.1.22.2.3.1.1.12	Counter	read-only	This counter is incremented by one for each CarrierEvent on this port whose ActivityDuration is greater than the MAU Jabber Lockup Protection timer TW3 (Ref: 9.6.1 & 9.6.5, IEEE 802.3 Std). Other counters may be incremented as appropriate.
rptrMonitorRptrInfo	1.3.6.1.2.1.22.2.1
CTR rptrMonitorTransmitCollisions	1.3.6.1.2.1.22.2.1.1	Counter	read-only	This counter is incremented every time the repeater state machine enters the TRANSMIT COLLISION state from any state other than ONE PORT LEFT (Ref: Fig 9-2, IEEE 802.3 Std). The approximate minimum time for rollover of this counter is 16 hours.
INT rptrNonDisruptTest	1.3.6.1.2.1.22.1.1.5	INTEGER	read-write	Setting this object to selfTest(2) causes the repeater to perform a agent-specific, non- disruptive self-test that has the following characteristics: a) The nature of the tests is not specified. b) The test does not change the state of the repeater or management information about the repeater. c) The test does not inject packets onto any segment. d) The test does not prevent the relay of any packets. e) The test does not interfere with management functions. After performing this test the agent will update the repeater health information and send a rptrHealth trap. Setting this object to noSelfTest(1) has no effect. The agent will always return the value noSelfTest(1) when this object is read.
INT rptrOperStatus	1.3.6.1.2.1.22.1.1.2	INTEGER	read-only	The rptrOperStatus object indicates the operational state of the repeater. The rptrHealthText object may be consulted for more specific information about the state of the repeater's health. In the case of multiple kinds of failures (e.g., repeater failure and port failure), the value of this attribute shall reflect the highest priority failure in the following order: rptrFailure(3) groupFailure(4) portFailure(5) generalFailure(6).
INT rptrPortAdminStatus	1.3.6.1.2.1.22.1.3.1.1.3	INTEGER	read-write	Setting this object to disabled(2) disables the port. A disabled port neither transmits nor receives. Once disabled, a port must be explicitly enabled to restore operation. A port which is disabled when power is lost or when a reset is exerted shall remain disabled when normal operation resumes. The admin status takes precedence over auto- partition and functionally operates between the auto-partition mechanism and the AUI/PMA. Setting this object to enabled(1) enables the port and exerts a BEGIN on the port's auto-partition state machine. (In effect, when a port is disabled, the value of rptrPortAutoPartitionState for that port is frozen until the port is next enabled. When the port becomes enabled, the rptrPortAutoPartitionState becomes notAutoPartitioned(1), regardless of its pre-disabling state.)
INT rptrPortAutoPartitionState	1.3.6.1.2.1.22.1.3.1.1.4	INTEGER	read-only	The autoPartitionState flag indicates whether the port is currently partitioned by the repeater's auto-partition protection. The conditions that cause port partitioning are specified in partition state machine in Section 9 [IEEE 802.3 Std]. They are not differentiated here.
rptrPortEntry	1.3.6.1.2.1.22.1.3.1.1		not-accessible	An entry in the table, containing information about a single port.
INT rptrPortGroupIndex	1.3.6.1.2.1.22.1.3.1.1.1	INTEGER	read-only	This object identifies the group containing the port for which this entry contains information.
INT rptrPortIndex	1.3.6.1.2.1.22.1.3.1.1.2	INTEGER	read-only	This object identifies the port within the group for which this entry contains information. This value can never be greater than rptrGroupPortCapacity for the associated group.
rptrPortInfo	1.3.6.1.2.1.22.1.3
INT rptrPortOperStatus	1.3.6.1.2.1.22.1.3.1.1.5	INTEGER	read-only	This object indicates the port's operational status. The notPresent(3) status indicates the port is physically removed (note this may or may not be possible depending on the type of port.) The operational(1) status indicates that the port is enabled (see rptrPortAdminStatus) and working, even though it might be auto-partitioned (see rptrPortAutoPartitionState). If this object has the value operational(1) and rptrPortAdminStatus is set to disabled(2), it is expected that this object's value will change to notOperational(2) soon after.
rptrPortTable	1.3.6.1.2.1.22.1.3.1		not-accessible	Table of descriptive and status information about the ports.
INT rptrReset	1.3.6.1.2.1.22.1.1.4	INTEGER	read-write	Setting this object to reset(2) causes a transition to the START state of Fig 9-2 in section 9 [IEEE 802.3 Std]. Setting this object to noReset(1) has no effect. The agent will always return the value noReset(1) when this object is read. This action does not reset the management counters defined in this document nor does it affect the portAdminStatus parameters. Included in this action is the execution of a disruptive Self-Test with the following characteristics: a) The nature of the tests is not specified. b) The test resets the repeater but without affecting management information about the repeater. c) The test does not inject packets onto any segment. d) Packets received during the test may or may not be transferred. e) The test does not interfere with management functions. As a result of this action a rptrResetEvent trap should be sent.
NTF rptrResetEvent	1.3.6.1.2.1.22.0.3			The rptrResetEvent trap conveys information related to the operational status of the repeater. This trap is sent on completion of a repeater reset action. A repeater reset action is defined as an a transition to the START state of Fig 9-2 in section 9 [IEEE 802.3 Std], when triggered by a management command (e.g., an SNMP Set on the rptrReset object). The agent must throttle the generation of consecutive rptrResetEvent traps so that there is at least a five-second gap between them. The rptrResetEvent trap is not sent when the agent restarts and sends an SNMP coldStart or warmStart trap. However, it is recommended that a repeater agent send the rptrOperStatus object as an optional object with its coldStart and warmStart trap PDUs. The rptrOperStatus object must be included in the varbind list sent with this trap. The agent may optionally include the rptrHealthText object as well.
rptrRptrInfo	1.3.6.1.2.1.22.1.1
GAU rptrTotalPartitionedPorts	1.3.6.1.2.1.22.1.1.6	Gauge	read-only	This object returns the total number of ports in the repeater whose current state meets all three of the following criteria: rptrPortOperStatus does not have the value notPresent(3), rptrPortAdminStatus is enabled(1), and rptrPortAutoPartitionState is autoPartitioned(2).
snmp	1.3.6.1.2.1.11
snmpDot3RptrMgt	1.3.6.1.2.1.22
INT snmpEnableAuthenTraps	1.3.6.1.2.1.11.30	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate authentication-failure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authentication-failure traps may be disabled. Note that it is strongly recommended that this object be stored in non-volatile memory so that it remains constant between re-initializations of the network management system.
CTR snmpInASNParseErrs	1.3.6.1.2.1.11.6	Counter	read-only	The total number of ASN.1 or BER errors encountered by the SNMP protocol entity when decoding received SNMP Messages.
CTR snmpInBadCommunityNames	1.3.6.1.2.1.11.4	Counter	read-only	The total number of SNMP Messages delivered to the SNMP protocol entity which used a SNMP community name not known to said entity.
CTR snmpInBadCommunityUses	1.3.6.1.2.1.11.5	Counter	read-only	The total number of SNMP Messages delivered to the SNMP protocol entity which represented an SNMP operation which was not allowed by the SNMP community named in the Message.
CTR snmpInBadValues	1.3.6.1.2.1.11.10	Counter	read-only	The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `badValue'.
CTR snmpInBadVersions	1.3.6.1.2.1.11.3	Counter	read-only	The total number of SNMP Messages which were delivered to the SNMP protocol entity and were for an unsupported SNMP version.
CTR snmpInGenErrs	1.3.6.1.2.1.11.12	Counter	read-only	The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `genErr'.
CTR snmpInGetNexts	1.3.6.1.2.1.11.16	Counter	read-only	The total number of SNMP Get-Next PDUs which have been accepted and processed by the SNMP protocol entity.
CTR snmpInGetRequests	1.3.6.1.2.1.11.15	Counter	read-only	The total number of SNMP Get-Request PDUs which have been accepted and processed by the SNMP protocol entity.
CTR snmpInGetResponses	1.3.6.1.2.1.11.18	Counter	read-only	The total number of SNMP Get-Response PDUs which have been accepted and processed by the SNMP protocol entity.
CTR snmpInNoSuchNames	1.3.6.1.2.1.11.9	Counter	read-only	The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `noSuchName'.
CTR snmpInPkts	1.3.6.1.2.1.11.1	Counter	read-only	The total number of Messages delivered to the SNMP entity from the transport service.
CTR snmpInReadOnlys	1.3.6.1.2.1.11.11	Counter	read-only	The total number valid SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `readOnly'. It should be noted that it is a protocol error to generate an SNMP PDU which contains the value `readOnly' in the error-status field, as such this object is provided as a means of detecting incorrect implementations of the SNMP.
CTR snmpInSetRequests	1.3.6.1.2.1.11.17	Counter	read-only	The total number of SNMP Set-Request PDUs which have been accepted and processed by the SNMP protocol entity.
CTR snmpInTooBigs	1.3.6.1.2.1.11.8	Counter	read-only	The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `tooBig'.
CTR snmpInTotalReqVars	1.3.6.1.2.1.11.13	Counter	read-only	The total number of MIB objects which have been retrieved successfully by the SNMP protocol entity as the result of receiving valid SNMP Get-Request and Get-Next PDUs.
CTR snmpInTotalSetVars	1.3.6.1.2.1.11.14	Counter	read-only	The total number of MIB objects which have been altered successfully by the SNMP protocol entity as the result of receiving valid SNMP Set-Request PDUs.
CTR snmpInTraps	1.3.6.1.2.1.11.19	Counter	read-only	The total number of SNMP Trap PDUs which have been accepted and processed by the SNMP protocol entity.
CTR snmpOutBadValues	1.3.6.1.2.1.11.22	Counter	read-only	The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `badValue'.
CTR snmpOutGenErrs	1.3.6.1.2.1.11.24	Counter	read-only	The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `genErr'.
CTR snmpOutGetNexts	1.3.6.1.2.1.11.26	Counter	read-only	The total number of SNMP Get-Next PDUs which have been generated by the SNMP protocol entity.
CTR snmpOutGetRequests	1.3.6.1.2.1.11.25	Counter	read-only	The total number of SNMP Get-Request PDUs which have been generated by the SNMP protocol entity.
CTR snmpOutGetResponses	1.3.6.1.2.1.11.28	Counter	read-only	The total number of SNMP Get-Response PDUs which have been generated by the SNMP protocol entity.
CTR snmpOutNoSuchNames	1.3.6.1.2.1.11.21	Counter	read-only	The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status is `noSuchName'.
CTR snmpOutPkts	1.3.6.1.2.1.11.2	Counter	read-only	The total number of SNMP Messages which were passed from the SNMP protocol entity to the transport service.
CTR snmpOutSetRequests	1.3.6.1.2.1.11.27	Counter	read-only	The total number of SNMP Set-Request PDUs which have been generated by the SNMP protocol entity.
CTR snmpOutTooBigs	1.3.6.1.2.1.11.20	Counter	read-only	The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `tooBig.'
CTR snmpOutTraps	1.3.6.1.2.1.11.29	Counter	read-only	The total number of SNMP Trap PDUs which have been generated by the SNMP protocol entity.
STR sysContact	1.3.6.1.2.1.1.4	DisplayString	read-write	The textual identification of the contact person for this managed node, together with information on how to contact this person.
STR sysDescr	1.3.6.1.2.1.1.1	DisplayString	read-only	A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters.
STR sysLocation	1.3.6.1.2.1.1.6	DisplayString	read-write	The physical location of this node (e.g., `telephone closet, 3rd floor').
STR sysName	1.3.6.1.2.1.1.5	DisplayString	read-write	An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name.
OID sysObjectID	1.3.6.1.2.1.1.2	OBJECT IDENTIFIER	read-only	The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining `what kind of box' is being managed. For example, if vendor `Flintstones, Inc.' was assigned the subtree 1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its `Fred Router'.
INT sysServices	1.3.6.1.2.1.1.7	INTEGER	read-only	A value which indicates the set of services that this entity primarily offers. The value is a sum. This sum initially takes the value zero, Then, for each layer, L, in the range 1 through 7, that this node performs transactions for, 2 raised to (L - 1) is added to the sum. For example, a node which performs primarily routing functions would have a value of 4 (2^(3-1)). In contrast, a node which is a host offering application services would have a value of 72 (2^(4-1) + 2^(7-1)). Note that in the context of the Internet suite of protocols, values should be calculated accordingly: layer functionality 1 physical (e.g., repeaters) 2 datalink/subnetwork (e.g., bridges) 3 internet (e.g., IP gateways) 4 end-to-end (e.g., IP hosts) 7 applications (e.g., mail relays) For systems including OSI protocols, layers 5 and 6 may also be counted.
system	1.3.6.1.2.1.1
TIK sysUpTime	1.3.6.1.2.1.1.3	TimeTicks	read-only	The time (in hundredths of a second) since the network management portion of the system was last re-initialized.
tcp	1.3.6.1.2.1.6
CTR tcpActiveOpens	1.3.6.1.2.1.6.5	Counter	read-only	The number of times TCP connections have made a direct transition to the SYN-SENT state from the CLOSED state.
CTR tcpAttemptFails	1.3.6.1.2.1.6.7	Counter	read-only	The number of times TCP connections have made a direct transition to the CLOSED state from either the SYN-SENT state or the SYN-RCVD state, plus the number of times TCP connections have made a direct transition to the LISTEN state from the SYN-RCVD state.
tcpConnEntry	1.3.6.1.2.1.6.13.1		not-accessible	Information about a particular current TCP connection. An object of this type is transient, in that it ceases to exist when (or soon after) the connection makes the transition to the CLOSED state.
IP tcpConnLocalAddress	1.3.6.1.2.1.6.13.1.2	IpAddress	read-only	The local IP address for this TCP connection. In the case of a connection in the listen state which is willing to accept connections for any IP interface associated with the node, the value 0.0.0.0 is used.
INT tcpConnLocalPort	1.3.6.1.2.1.6.13.1.3	INTEGER	read-only	The local port number for this TCP connection.
IP tcpConnRemAddress	1.3.6.1.2.1.6.13.1.4	IpAddress	read-only	The remote IP address for this TCP connection.
INT tcpConnRemPort	1.3.6.1.2.1.6.13.1.5	INTEGER	read-only	The remote port number for this TCP connection.
INT tcpConnState	1.3.6.1.2.1.6.13.1.1	INTEGER	read-write	The state of this TCP connection. The only value which may be set by a management station is deleteTCB(12). Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to set this object to any other value. If a management station sets this object to the value deleteTCB(12), then this has the effect of deleting the TCB (as defined in RFC 793) of the corresponding connection on the managed node, resulting in immediate termination of the connection. As an implementation-specific option, a RST segment may be sent from the managed node to the other TCP endpoint (note however that RST segments are not sent reliably).
tcpConnTable	1.3.6.1.2.1.6.13		not-accessible	A table containing TCP connection-specific information.
GAU tcpCurrEstab	1.3.6.1.2.1.6.9	Gauge	read-only	The number of TCP connections for which the current state is either ESTABLISHED or CLOSE- WAIT.
CTR tcpEstabResets	1.3.6.1.2.1.6.8	Counter	read-only	The number of times TCP connections have made a direct transition to the CLOSED state from either the ESTABLISHED state or the CLOSE-WAIT state.
CTR tcpInErrs	1.3.6.1.2.1.6.14	Counter	read-only	The total number of segments received in error (e.g., bad TCP checksums).
CTR tcpInSegs	1.3.6.1.2.1.6.10	Counter	read-only	The total number of segments received, including those received in error. This count includes segments received on currently established connections.
INT tcpMaxConn	1.3.6.1.2.1.6.4	INTEGER	read-only	The limit on the total number of TCP connections the entity can support. In entities where the maximum number of connections is dynamic, this object should contain the value -1.
CTR tcpOutRsts	1.3.6.1.2.1.6.15	Counter	read-only	The number of TCP segments sent containing the RST flag.
CTR tcpOutSegs	1.3.6.1.2.1.6.11	Counter	read-only	The total number of segments sent, including those on current connections but excluding those containing only retransmitted octets.
CTR tcpPassiveOpens	1.3.6.1.2.1.6.6	Counter	read-only	The number of times TCP connections have made a direct transition to the SYN-RCVD state from the LISTEN state.
CTR tcpRetransSegs	1.3.6.1.2.1.6.12	Counter	read-only	The total number of segments retransmitted - that is, the number of TCP segments transmitted containing one or more previously transmitted octets.
INT tcpRtoAlgorithm	1.3.6.1.2.1.6.1	INTEGER	read-only	The algorithm used to determine the timeout value used for retransmitting unacknowledged octets.
INT tcpRtoMax	1.3.6.1.2.1.6.3	INTEGER	read-only	The maximum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the UBOUND quantity described in RFC 793.
INT tcpRtoMin	1.3.6.1.2.1.6.2	INTEGER	read-only	The minimum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the LBOUND quantity described in RFC 793.
NTF topologyChange	1.3.6.1.2.1.17.0.2			A topologyChange trap is sent by a bridge when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. The trap is not sent if a newRoot trap is sent for the same transition.
transmission	1.3.6.1.2.1.10
udp	1.3.6.1.2.1.7
udpEntry	1.3.6.1.2.1.7.5.1		not-accessible	Information about a particular current UDP listener.
CTR udpInDatagrams	1.3.6.1.2.1.7.1	Counter	read-only	The total number of UDP datagrams delivered to UDP users.
CTR udpInErrors	1.3.6.1.2.1.7.3	Counter	read-only	The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port.
IP udpLocalAddress	1.3.6.1.2.1.7.5.1.1	IpAddress	read-only	The local IP address for this UDP listener. In the case of a UDP listener which is willing to accept datagrams for any IP interface associated with the node, the value 0.0.0.0 is used.
INT udpLocalPort	1.3.6.1.2.1.7.5.1.2	INTEGER	read-only	The local port number for this UDP listener.
CTR udpNoPorts	1.3.6.1.2.1.7.2	Counter	read-only	The total number of received UDP datagrams for which there was no application at the destination port.
CTR udpOutDatagrams	1.3.6.1.2.1.7.4	Counter	read-only	The total number of UDP datagrams sent from this entity.
udpTable	1.3.6.1.2.1.7.5		not-accessible	A table containing UDP listener information.

at

1.3.6.1.2.1.3

atEntry

1.3.6.1.2.1.3.1.1

not-accessible

Each entry contains one NetworkAddress to `physical' address equivalence.

INT atIfIndex

1.3.6.1.2.1.3.1.1.1

INTEGER

read-write

The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

IP atNetAddress

1.3.6.1.2.1.3.1.1.3

IpAddress

read-write

The NetworkAddress (e.g., the IP address) corresponding to the media-dependent `physical' address.

PHY atPhysAddress

1.3.6.1.2.1.3.1.1.2

PhysAddress

read-write

The media-dependent `physical' address. Setting this object to a null string (one of zero length) has the effect of invaliding the corresponding entry in the atTable object. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant atPhysAddress object.

atTable

1.3.6.1.2.1.3.1

not-accessible

The Address Translation tables contain the NetworkAddress to `physical' address equivalences. Some interfaces do not use translation tables for determining address equivalences (e.g., DDN-X.25 has an algorithmic method); if all interfaces are of this type, then the Address Translation table is empty, i.e., has zero entries.

bbAui

1.3.6.1.4.1.712.1.1.1.3.0

bbAui10BASE_FL

1.3.6.1.4.1.712.1.1.1.3.4

bbAuiBnc

1.3.6.1.4.1.712.1.1.1.3.2

bbAuiTp

1.3.6.1.4.1.712.1.1.1.3.1

bbAuiTpBnc

1.3.6.1.4.1.712.1.1.1.3.3

ccitt

0

directory

1.3.6.1.1

dod

1.3.6

1.3.6.1.2.1.17.1

1.3.6.1.2.1.17

1.3.6.1.2.1.17.3

1.3.6.1.2.1.17.5

1.3.6.1.2.1.17.2

1.3.6.1.2.1.17.4

egp

1.3.6.1.2.1.8

enterprises

1.3.6.1.4.1

ete120x

1.3.6.1.4.1.712.1.1.1.2.12

ete160x

1.3.6.1.4.1.712.1.1.1.2.16

ete240x

1.3.6.1.4.1.712.1.1.1.2.24

etm120x

1.3.6.1.4.1.712.1.1.1.1.12

etm160x

1.3.6.1.4.1.712.1.1.1.1.16

etm240x

1.3.6.1.4.1.712.1.1.1.1.24

experimental

1.3.6.1.3

icmp

1.3.6.1.2.1.5

CTR icmpInAddrMaskReps

1.3.6.1.2.1.5.13

Counter

read-only

The number of ICMP Address Mask Reply messages received.

CTR icmpInAddrMasks

1.3.6.1.2.1.5.12

Counter

read-only

The number of ICMP Address Mask Request messages received.

CTR icmpInDestUnreachs

1.3.6.1.2.1.5.3

Counter

read-only

The number of ICMP Destination Unreachable messages received.

CTR icmpInEchoReps

1.3.6.1.2.1.5.9

Counter

read-only

The number of ICMP Echo Reply messages received.

CTR icmpInEchos

1.3.6.1.2.1.5.8

Counter

read-only

The number of ICMP Echo (request) messages received.

CTR icmpInErrors

1.3.6.1.2.1.5.2

Counter

read-only

The number of ICMP messages which the entity received but determined as having ICMP-specific errors (bad ICMP checksums, bad length, etc.).

CTR icmpInMsgs

1.3.6.1.2.1.5.1

Counter

read-only

The total number of ICMP messages which the entity received. Note that this counter includes all those counted by icmpInErrors.

CTR icmpInParmProbs

1.3.6.1.2.1.5.5

Counter

read-only

The number of ICMP Parameter Problem messages received.

CTR icmpInRedirects

1.3.6.1.2.1.5.7

Counter

read-only

The number of ICMP Redirect messages received.

CTR icmpInSrcQuenchs

1.3.6.1.2.1.5.6

Counter

read-only

The number of ICMP Source Quench messages received.

CTR icmpInTimeExcds

1.3.6.1.2.1.5.4

Counter

read-only

The number of ICMP Time Exceeded messages received.

CTR icmpInTimestampReps

1.3.6.1.2.1.5.11

Counter

read-only

The number of ICMP Timestamp Reply messages received.

CTR icmpInTimestamps

1.3.6.1.2.1.5.10

Counter

read-only

The number of ICMP Timestamp (request) messages received.

CTR icmpOutAddrMaskReps

1.3.6.1.2.1.5.26

Counter

read-only

The number of ICMP Address Mask Reply messages sent.

CTR icmpOutAddrMasks

1.3.6.1.2.1.5.25

Counter

read-only

The number of ICMP Address Mask Request messages sent.

CTR icmpOutDestUnreachs

1.3.6.1.2.1.5.16

Counter

read-only

The number of ICMP Destination Unreachable messages sent.

CTR icmpOutEchoReps

1.3.6.1.2.1.5.22

Counter

read-only

The number of ICMP Echo Reply messages sent.

CTR icmpOutEchos

1.3.6.1.2.1.5.21

Counter

read-only

The number of ICMP Echo (request) messages sent.

CTR icmpOutErrors

1.3.6.1.2.1.5.15

Counter

read-only

The number of ICMP messages which this entity did not send due to problems discovered within ICMP such as a lack of buffers. This value should not include errors discovered outside the ICMP layer such as the inability of IP to route the resultant datagram. In some implementations there may be no types of error which contribute to this counter's value.

CTR icmpOutMsgs

1.3.6.1.2.1.5.14

Counter

read-only

The total number of ICMP messages which this entity attempted to send. Note that this counter includes all those counted by icmpOutErrors.

CTR icmpOutParmProbs

1.3.6.1.2.1.5.18

Counter

read-only

The number of ICMP Parameter Problem messages sent.

CTR icmpOutRedirects

1.3.6.1.2.1.5.20

Counter

read-only

The number of ICMP Redirect messages sent. For a host, this object will always be zero, since hosts do not send redirects.

CTR icmpOutSrcQuenchs

1.3.6.1.2.1.5.19

Counter

read-only

The number of ICMP Source Quench messages sent.

CTR icmpOutTimeExcds

1.3.6.1.2.1.5.17

Counter

read-only

The number of ICMP Time Exceeded messages sent.

CTR icmpOutTimestampReps

1.3.6.1.2.1.5.24

Counter

read-only

The number of ICMP Timestamp Reply messages sent.

CTR icmpOutTimestamps

1.3.6.1.2.1.5.23

Counter

read-only

The number of ICMP Timestamp (request) messages sent.

INT ifAdminStatus

1.3.6.1.2.1.2.2.1.7

INTEGER

read-write

The desired state of the interface. The testing(3) state indicates that no operational packets can be passed.

STR ifDescr

1.3.6.1.2.1.2.2.1.2

DisplayString

read-only

A textual string containing information about the interface. This string should include the name of the manufacturer, the product name and the version of the hardware interface.

ifEntry

1.3.6.1.2.1.2.2.1

not-accessible

An interface entry containing objects at the subnetwork layer and below for a particular interface.

INT ifIndex

1.3.6.1.2.1.2.2.1.1

INTEGER

read-only

A unique value for each interface. Its value ranges between 1 and the value of ifNumber. The value for each interface must remain constant at least from one re-initialization of the entity's network management system to the next re- initialization.

CTR ifInDiscards

1.3.6.1.2.1.2.2.1.13

Counter

read-only

The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet could be to free up buffer space.

CTR ifInErrors

1.3.6.1.2.1.2.2.1.14

Counter

read-only

The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol.

CTR ifInNUcastPkts

1.3.6.1.2.1.2.2.1.12

Counter

read-only

The number of non-unicast (i.e., subnetwork- broadcast or subnetwork-multicast) packets delivered to a higher-layer protocol.

CTR ifInOctets

1.3.6.1.2.1.2.2.1.10

Counter

read-only

The total number of octets received on the interface, including framing characters.

CTR ifInUcastPkts

1.3.6.1.2.1.2.2.1.11

Counter

read-only

The number of subnetwork-unicast packets delivered to a higher-layer protocol.

CTR ifInUnknownProtos

1.3.6.1.2.1.2.2.1.15

Counter

read-only

The number of packets received via the interface which were discarded because of an unknown or unsupported protocol.

TIK ifLastChange

1.3.6.1.2.1.2.2.1.9

TimeTicks

read-only

The value of sysUpTime at the time the interface entered its current operational state. If the current state was entered prior to the last re- initialization of the local network management subsystem, then this object contains a zero value.

INT ifMtu

1.3.6.1.2.1.2.2.1.4

INTEGER

read-only

The size of the largest datagram which can be sent/received on the interface, specified in octets. For interfaces that are used for transmitting network datagrams, this is the size of the largest network datagram that can be sent on the interface.

INT ifNumber

1.3.6.1.2.1.2.1

INTEGER

read-only

The number of network interfaces (regardless of their current state) present on this system.

INT ifOperStatus

1.3.6.1.2.1.2.2.1.8

INTEGER

read-only

The current operational state of the interface. The testing(3) state indicates that no operational packets can be passed.

CTR ifOutDiscards

1.3.6.1.2.1.2.2.1.19

Counter

read-only

The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer space.

CTR ifOutErrors

1.3.6.1.2.1.2.2.1.20

Counter

read-only

The number of outbound packets that could not be transmitted because of errors.

CTR ifOutNUcastPkts

1.3.6.1.2.1.2.2.1.18

Counter

read-only

The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent.

CTR ifOutOctets

1.3.6.1.2.1.2.2.1.16

Counter

read-only

The total number of octets transmitted out of the interface, including framing characters.

GAU ifOutQLen

1.3.6.1.2.1.2.2.1.21

Gauge

read-only

The length of the output packet queue (in packets).

CTR ifOutUcastPkts

1.3.6.1.2.1.2.2.1.17

Counter

read-only

The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.

PHY ifPhysAddress

1.3.6.1.2.1.2.2.1.6

PhysAddress

read-only

The interface's address at the protocol layer immediately `below' the network layer in the protocol stack. For interfaces which do not have such an address (e.g., a serial line), this object should contain an octet string of zero length.

OID ifSpecific

1.3.6.1.2.1.2.2.1.22

OBJECT IDENTIFIER

read-only

A reference to MIB definitions specific to the particular media being used to realize the interface. For example, if the interface is realized by an ethernet, then the value of this object refers to a document defining objects specific to ethernet. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value.

GAU ifSpeed

1.3.6.1.2.1.2.2.1.5

Gauge

read-only

An estimate of the interface's current bandwidth in bits per second. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth.

ifTable

1.3.6.1.2.1.2.2

not-accessible

A list of interface entries. The number of entries is given by the value of ifNumber.

INT ifType

1.3.6.1.2.1.2.2.1.3

INTEGER

read-only

The type of interface, distinguished according to the physical/link protocol(s) immediately `below' the network layer in the protocol stack.

interfaces

1.3.6.1.2.1.2

internet

1.3.6.1

ip

1.3.6.1.2.1.4

ipAddrEntry

1.3.6.1.2.1.4.20.1

not-accessible

The addressing information for one of this entity's IP addresses.

ipAddrTable

1.3.6.1.2.1.4.20

not-accessible

The table of addressing information relevant to this entity's IP addresses.

IP ipAdEntAddr

1.3.6.1.2.1.4.20.1.1

IpAddress

read-only

The IP address to which this entry's addressing information pertains.

INT ipAdEntBcastAddr

1.3.6.1.2.1.4.20.1.4

INTEGER

read-only

The value of the least-significant bit in the IP broadcast address used for sending datagrams on the (logical) interface associated with the IP address of this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this (logical) interface.

INT ipAdEntIfIndex

1.3.6.1.2.1.4.20.1.2

INTEGER

read-only

The index value which uniquely identifies the interface to which this entry is applicable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

IP ipAdEntNetMask

1.3.6.1.2.1.4.20.1.3

IpAddress

read-only

The subnet mask associated with the IP address of this entry. The value of the mask is an IP address with all the network bits set to 1 and all the hosts bits set to 0.

INT ipAdEntReasmMaxSize

1.3.6.1.2.1.4.20.1.5

INTEGER

read-only

The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface.

INT ipDefaultTTL

1.3.6.1.2.1.4.2

INTEGER

read-write

The default value inserted into the Time-To-Live field of the IP header of datagrams originated at this entity, whenever a TTL value is not supplied by the transport layer protocol.

INT ipForwarding

1.3.6.1.2.1.4.1

INTEGER

read-write

The indication of whether this entity is acting as an IP gateway in respect to the forwarding of datagrams received by, but not addressed to, this entity. IP gateways forward datagrams. IP hosts do not (except those source-routed via the host). Note that for some managed nodes, this object may take on only a subset of the values possible. Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to change this object to an inappropriate value.

CTR ipForwDatagrams

1.3.6.1.2.1.4.6

Counter

read-only

The number of input datagrams for which this entity was not their final IP destination, as a result of which an attempt was made to find a route to forward them to that final destination. In entities which do not act as IP Gateways, this counter will include only those packets which were Source-Routed via this entity, and the Source- Route option processing was successful.

CTR ipFragCreates

1.3.6.1.2.1.4.19

Counter

read-only

The number of IP datagram fragments that have been generated as a result of fragmentation at this entity.

CTR ipFragFails

1.3.6.1.2.1.4.18

Counter

read-only

The number of IP datagrams that have been discarded because they needed to be fragmented at this entity but could not be, e.g., because their Don't Fragment flag was set.

CTR ipFragOKs

1.3.6.1.2.1.4.17

Counter

read-only

The number of IP datagrams that have been successfully fragmented at this entity.

CTR ipInAddrErrors

1.3.6.1.2.1.4.5

Counter

read-only

The number of input datagrams discarded because the IP address in their IP header's destination field was not a valid address to be received at this entity. This count includes invalid addresses (e.g., 0.0.0.0) and addresses of unsupported Classes (e.g., Class E). For entities which are not IP Gateways and therefore do not forward datagrams, this counter includes datagrams discarded because the destination address was not a local address.

CTR ipInDelivers

1.3.6.1.2.1.4.9

Counter

read-only

The total number of input datagrams successfully delivered to IP user-protocols (including ICMP).

CTR ipInDiscards

1.3.6.1.2.1.4.8

Counter

read-only

The number of input IP datagrams for which no problems were encountered to prevent their continued processing, but which were discarded (e.g., for lack of buffer space). Note that this counter does not include any datagrams discarded while awaiting re-assembly.

CTR ipInHdrErrors

1.3.6.1.2.1.4.4

Counter

read-only

The number of input datagrams discarded due to errors in their IP headers, including bad checksums, version number mismatch, other format errors, time-to-live exceeded, errors discovered in processing their IP options, etc.

CTR ipInReceives

1.3.6.1.2.1.4.3

Counter

read-only

The total number of input datagrams received from interfaces, including those received in error.

CTR ipInUnknownProtos

1.3.6.1.2.1.4.7

Counter

read-only

The number of locally-addressed datagrams received successfully but discarded because of an unknown or unsupported protocol.

ipNetToMediaEntry

1.3.6.1.2.1.4.22.1

not-accessible

Each entry contains one IpAddress to `physical' address equivalence.

INT ipNetToMediaIfIndex

1.3.6.1.2.1.4.22.1.1

INTEGER

read-write

The interface on which this entry's equivalence is effective. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

IP ipNetToMediaNetAddress

1.3.6.1.2.1.4.22.1.3

IpAddress

read-only

The IpAddress corresponding to the media- dependent `physical' address.

PHY ipNetToMediaPhysAddress

1.3.6.1.2.1.4.22.1.2

PhysAddress

read-write

The media-dependent `physical' address.

ipNetToMediaTable

1.3.6.1.2.1.4.22

not-accessible

The IP Address Translation table used for mapping from IP addresses to physical addresses.

INT ipNetToMediaType

1.3.6.1.2.1.4.22.1.4

INTEGER

read-write

The type of mapping. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipNetToMediaTable. That is, it effectively dissasociates the interface identified with said entry from the mapping identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipNetToMediaType object.

CTR ipOutDiscards

1.3.6.1.2.1.4.11

Counter

read-only

The number of output IP datagrams for which no problem was encountered to prevent their transmission to their destination, but which were discarded (e.g., for lack of buffer space). Note that this counter would include datagrams counted in ipForwDatagrams if any such packets met this (discretionary) discard criterion.

CTR ipOutNoRoutes

1.3.6.1.2.1.4.12

Counter

read-only

The number of IP datagrams discarded because no route could be found to transmit them to their destination. Note that this counter includes any packets counted in ipForwDatagrams which meet this `no-route' criterion. Note that this includes any datagarms which a host cannot route because all of its default gateways are down.

CTR ipOutRequests

1.3.6.1.2.1.4.10

Counter

read-only

The total number of IP datagrams which local IP user-protocols (including ICMP) supplied to IP in requests for transmission. Note that this counter does not include any datagrams counted in ipForwDatagrams.

CTR ipReasmFails

1.3.6.1.2.1.4.16

Counter

read-only

The number of failures detected by the IP re- assembly algorithm (for whatever reason: timed out, errors, etc). Note that this is not necessarily a count of discarded IP fragments since some algorithms (notably the algorithm in RFC 815) can lose track of the number of fragments by combining them as they are received.

CTR ipReasmOKs

1.3.6.1.2.1.4.15

Counter

read-only

The number of IP datagrams successfully re- assembled.

CTR ipReasmReqds

1.3.6.1.2.1.4.14

Counter

read-only

The number of IP fragments received which needed to be reassembled at this entity.

INT ipReasmTimeout

1.3.6.1.2.1.4.13

INTEGER

read-only

The maximum number of seconds which received fragments are held while they are awaiting reassembly at this entity.

INT ipRouteAge

1.3.6.1.2.1.4.21.1.10

INTEGER

read-write

The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned.

IP ipRouteDest

1.3.6.1.2.1.4.21.1.1

IpAddress

read-write

The destination IP address of this route. An entry with a value of 0.0.0.0 is considered a default route. Multiple routes to a single destination can appear in the table, but access to such multiple entries is dependent on the table- access mechanisms defined by the network management protocol in use.

ipRouteEntry

1.3.6.1.2.1.4.21.1

not-accessible

A route to a particular destination.

INT ipRouteIfIndex

1.3.6.1.2.1.4.21.1.2

INTEGER

read-write

The index value which uniquely identifies the local interface through which the next hop of this route should be reached. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex.

OID ipRouteInfo

1.3.6.1.2.1.4.21.1.13

OBJECT IDENTIFIER

read-only

A reference to MIB definitions specific to the particular routing protocol which is responsible for this route, as determined by the value specified in the route's ipRouteProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntatically valid object identifier, and any conformant implementation of ASN.1 and BER must be able to generate and recognize this value.

IP ipRouteMask

1.3.6.1.2.1.4.21.1.11

IpAddress

read-write

Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipRouteMask by determining whether the value of the correspondent ipRouteDest field belong to a class-A, B, or C network, and then using one of: mask network 255.0.0.0 class-A 255.255.0.0 class-B 255.255.255.0 class-C If the value of the ipRouteDest is 0.0.0.0 (a default route), then the mask value is also 0.0.0.0. It should be noted that all IP routing subsystems implicitly use this mechanism.

INT ipRouteMetric1

1.3.6.1.2.1.4.21.1.3

INTEGER

read-write

The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.

INT ipRouteMetric2

1.3.6.1.2.1.4.21.1.4

INTEGER

read-write

An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.

INT ipRouteMetric3

1.3.6.1.2.1.4.21.1.5

INTEGER

read-write

An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.

INT ipRouteMetric4

1.3.6.1.2.1.4.21.1.6

INTEGER

read-write

An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.

INT ipRouteMetric5

1.3.6.1.2.1.4.21.1.12

INTEGER

read-write

An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipRouteProto value. If this metric is not used, its value should be set to -1.

IP ipRouteNextHop

1.3.6.1.2.1.4.21.1.7

IpAddress

read-write

The IP address of the next hop of this route. (In the case of a route bound to an interface which is realized via a broadcast media, the value of this field is the agent's IP address on that interface.)

INT ipRouteProto

1.3.6.1.2.1.4.21.1.9

INTEGER

read-only

The routing mechanism via which this route was learned. Inclusion of values for gateway routing protocols is not intended to imply that hosts should support those protocols.

ipRouteTable

1.3.6.1.2.1.4.21

not-accessible

This entity's IP Routing table.

INT ipRouteType

1.3.6.1.2.1.4.21.1.8

INTEGER

read-write

The type of route. Note that the values direct(3) and indirect(4) refer to the notion of direct and indirect routing in the IP architecture. Setting this object to the value invalid(2) has the effect of invalidating the corresponding entry in the ipRouteTable object. That is, it effectively dissasociates the destination identified with said entry from the route identified with said entry. It is an implementation-specific matter as to whether the agent removes an invalidated entry from the table. Accordingly, management stations must be prepared to receive tabular information from agents that corresponds to entries not currently in use. Proper interpretation of such entries requires examination of the relevant ipRouteType object.

CTR ipRoutingDiscards

1.3.6.1.2.1.4.23

Counter

read-only

The number of routing entries which were chosen to be discarded even though they are valid. One possible reason for discarding such an entry could be to free-up buffer space for other routing entries.

iso

1

laHubMib

1.3.6.1.4.1.712.1.2

INT laJoystick

1.3.6.1.4.1.712.1.2.1.2

INTEGER

read-write

Setting this object to disabled(2) prevents use of the four-position switch on the front panel. Resetting this object to enabled(1) allows use of the switch.

INT laLinkAlert

1.3.6.1.4.1.712.1.2.1.3

INTEGER

read-write

Setting this object enables or disables the LinkALERT feature of the backbone 10BASE-T or 10BASE-FL port. A return value of not-applicable indicates that none of the backbone ports feature LinkALERT.

1.3.6.1.4.1.712.1

1.3.6.1.4.1.712

1.3.6.1.4.1.712.1.1

1.3.6.1.4.1.712.1.2.1

INT laSysConfig

1.3.6.1.4.1.712.1.2.1.1

INTEGER

read-write

Setting this object to save(1) will save all configuration variables to non-volatile memory. Setting this object to load(2) will configure the hub according to the stored configuration. Setting this object to factory(3) will configure the hub according to the factory settings. A return value of ok(4) means the non-volatile memory is operational. A return value of failed(5) means the non-volatile memory has failed.

INT laTpAutoPolarity

1.3.6.1.4.1.712.1.2.2.1.1.4

INTEGER

read-write

Setting this object to disabled(2) disables the auto polarity test for this port. Setting this object to enabled(1) enables the feature. A return value of corrected(3) indicates that the polarity test has sensed a reversal on the receive wiring pair, and has corrected this fault by inverting its receive signal. A return value of not-applicable(4) indicates that the specified port does not support polarity correction.

laTpHub

1.3.6.1.4.1.712.1.1.1

laTpHub1

1.3.6.1.4.1.712.1.1.1.1

laTpHub2

1.3.6.1.4.1.712.1.1.1.2

laTpHub3

1.3.6.1.4.1.712.1.1.1.3

INT laTpLinkTest

1.3.6.1.4.1.712.1.2.2.1.1.3

INTEGER

read-write

Setting this object to disabled(2) disables the link test feature. This may be useful for interoperation with pre-10BASE-T equipment. Setting this object to enabled(1) enables the feature. A return value of failed(3) indicates a link test failure for this port. A return value of not-applicable(4) indicates that the specified port does not have a link test.

laTpPort

1.3.6.1.4.1.712.1.2.2

laTpPortEntry

1.3.6.1.4.1.712.1.2.2.1.1

not-accessible

An entry in the table, containing information about a single port.

INT laTpPortGroupIndex

1.3.6.1.4.1.712.1.2.2.1.1.1

INTEGER

read-only

This object identifies the group containing the port for which this entry contains information.

INT laTpPortIndex

1.3.6.1.4.1.712.1.2.2.1.1.2

INTEGER

read-only

This object identifies the port within the group for which this entry contains information.

laTpPortTable

1.3.6.1.4.1.712.1.2.2.1

not-accessible

Table of descriptive and status information about the ports.

mgmt

1.3.6.1.2

mib_2

1.3.6.1.2.1

NTF newRoot

1.3.6.1.2.1.17.0.1

The newRoot trap indicates that the sending agent has become the new root of the Spanning Tree; the trap is sent by a bridge soon after its election as the new root, e.g., upon expiration of the Topology Change Timer immediately subsequent to its election.

null

0.0

org

1.3

private

1.3.6.1.4

rptrAddrTrackEntry

1.3.6.1.2.1.22.3.3.1.1

not-accessible

An entry in the table, containing address mapping information about a single port.

INT rptrAddrTrackGroupIndex

1.3.6.1.2.1.22.3.3.1.1.1

INTEGER

read-only

This object identifies the group containing the port for which this entry contains information.

rptrAddrTrackGroupInfo

1.3.6.1.2.1.22.3.2

MAC rptrAddrTrackLastSourceAddress

1.3.6.1.2.1.22.3.3.1.1.3

MacAddress

read-only

This object is the SourceAddress of the last readable frame (i.e., counted by rptrMonitorPortReadableFrames) received by this port.

rptrAddrTrackPackage

1.3.6.1.2.1.22.3

INT rptrAddrTrackPortIndex

1.3.6.1.2.1.22.3.3.1.1.2

INTEGER

read-only

This object identifies the port within the group for which this entry contains information.

rptrAddrTrackPortInfo

1.3.6.1.2.1.22.3.3

rptrAddrTrackRptrInfo

1.3.6.1.2.1.22.3.1

CTR rptrAddrTrackSourceAddrChanges

1.3.6.1.2.1.22.3.3.1.1.4

Counter

read-only

This counter is incremented by one for each time that the rptrAddrTrackLastSourceAddress attribute for this port has changed. This may indicate whether a link is connected to a single DTE or another multi-user segment. The approximate minimum time for rollover of this counter is 81 hours.

rptrAddrTrackTable

1.3.6.1.2.1.22.3.3.1

not-accessible

Table of address mapping information about the ports.

rptrBasicPackage

1.3.6.1.2.1.22.1

INT rptrGroupCapacity

1.3.6.1.2.1.22.1.1.1

INTEGER

read-only

The rptrGroupCapacity is the number of groups that can be contained within the repeater. Within each managed repeater, the groups are uniquely numbered in the range from 1 to rptrGroupCapacity. Some groups may not be present in the repeater, in which case the actual number of groups present will be less than rptrGroupCapacity. The number of groups present will never be greater than rptrGroupCapacity. Note: In practice, this will generally be the number of field-replaceable units (i.e., modules, cards, or boards) that can fit in the physical repeater enclosure, and the group numbers will correspond to numbers marked on the physical enclosure.

NTF rptrGroupChange

1.3.6.1.2.1.22.0.2

This trap is sent when a change occurs in the group structure of a repeater. This occurs only when a group is logically or physically removed from or added to a repeater. The varBind list contains the identifier of the group that was removed or added. The agent must throttle the generation of consecutive rptrGroupChange traps for the same group so that there is at least a five-second gap between them.

STR rptrGroupDescr

1.3.6.1.2.1.22.1.2.1.1.2

DisplayString

read-only

A textual description of the group. This value should include the full name and version identification of the group's hardware type and indicate how the group is differentiated from other groups in the repeater. Plug-in Module, Rev A' or 'Barney Rubble 10BASE-T 4-port SIMM socket Version 2.1' are examples of valid group descriptions. It is mandatory that this only contain printable ASCII characters.

rptrGroupEntry

1.3.6.1.2.1.22.1.2.1.1

not-accessible

An entry in the table, containing information about a single group of ports.

INT rptrGroupIndex

1.3.6.1.2.1.22.1.2.1.1.1

INTEGER

read-only

This object identifies the group within the repeater for which this entry contains information. This value is never greater than rptrGroupCapacity.

rptrGroupInfo

1.3.6.1.2.1.22.1.2

TIK rptrGroupLastOperStatusChange

1.3.6.1.2.1.22.1.2.1.1.5

TimeTicks

read-only

An object that contains the value of sysUpTime at the time that the value of the rptrGroupOperStatus object for this group last changed. A value of zero indicates that the group's oper status has not changed since the agent last restarted.

OID rptrGroupObjectID

1.3.6.1.2.1.22.1.2.1.1.3

OBJECT IDENTIFIER

read-only

The vendor's authoritative identification of the group. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides a straight-forward and unambiguous means for determining what kind of group is being managed. For example, this object could take the value 1.3.6.1.4.1.4242.1.2.14 if vendor 'Flintstones, Inc.' was assigned the subtree 1.3.6.1.4.1.4242, and had assigned the identifier 1.3.6.1.4.1.4242.1.2.14 to its 'Wilma Flintstone 6-Port FOIRL Plug-in Module.'

INT rptrGroupOperStatus

1.3.6.1.2.1.22.1.2.1.1.4

INTEGER

read-only

An object that indicates the operational status of the group. A status of notPresent(4) indicates that the group is temporarily or permanently physically and/or logically not a part of the repeater. It is an implementation-specific matter as to whether the agent effectively removes notPresent entries from the table. A status of operational(2) indicates that the group is functioning, and a status of malfunctioning(3) indicates that the group is malfunctioning in some way.

INT rptrGroupPortCapacity

1.3.6.1.2.1.22.1.2.1.1.6

INTEGER

read-only

The rptrGroupPortCapacity is the number of ports that can be contained within the group. Valid range is 1-1024. Within each group, the ports are uniquely numbered in the range from 1 to rptrGroupPortCapacity. Note: In practice, this will generally be the number of ports on a module, card, or board, and the port numbers will correspond to numbers marked on the physical embodiment.

rptrGroupTable

1.3.6.1.2.1.22.1.2.1

not-accessible

Table of descriptive and status information about the groups of ports.

NTF rptrHealth

1.3.6.1.2.1.22.0.1

The rptrHealth trap conveys information related to the operational status of the repeater. This trap is sent only when the oper status of the repeater changes. The rptrHealth trap must contain the rptrOperStatus object. The agent may optionally include the rptrHealthText object in the varBind list. See the rptrOperStatus and rptrHealthText objects for descriptions of the information that is sent. The agent must throttle the generation of consecutive rptrHealth traps so that there is at least a five-second gap between them.

STR rptrHealthText

1.3.6.1.2.1.22.1.1.3

DisplayString

read-only

The health text object is a text string that provides information relevant to the operational state of the repeater. Agents may use this string to provide detailed information on current failures, including how they were detected, and/or instructions for problem resolution. The contents are agent-specific.

rptrMonitorGroupEntry

1.3.6.1.2.1.22.2.2.1.1

not-accessible

An entry in the table, containing total performance and error statistics for a single group. Regular retrieval of the information in this table provides a means of tracking the performance and health of the networked devices attached to this group's ports. The counters in this table are redundant in the sense that they are the summations of information already available through other objects. However, these sums provide a considerable optimization of network management traffic over the otherwise necessary retrieval of the individual counters included in each sum.

INT rptrMonitorGroupIndex

1.3.6.1.2.1.22.2.2.1.1.1

INTEGER

read-only

This object identifies the group within the repeater for which this entry contains information.

rptrMonitorGroupInfo

1.3.6.1.2.1.22.2.2

rptrMonitorGroupTable

1.3.6.1.2.1.22.2.2.1

not-accessible

Table of performance and error statistics for the groups.

CTR rptrMonitorGroupTotalErrors

1.3.6.1.2.1.22.2.2.1.1.4

Counter

read-only

The total number of errors which have occurred on all of the ports in this group. This counter is the summation of the values of the rptrMonitorPortTotalErrors counters for all of the ports in the group.

CTR rptrMonitorGroupTotalFrames

1.3.6.1.2.1.22.2.2.1.1.2

Counter

read-only

The total number of frames of valid frame length that have been received on the ports in this group. This counter is the summation of the values of the rptrMonitorPortReadableFrames counters for all of the ports in the group. This statistic provides one of the parameters necessary for obtaining the packet error rate. The approximate minimum time for rollover of this counter is 80 hours.

CTR rptrMonitorGroupTotalOctets

1.3.6.1.2.1.22.2.2.1.1.3

Counter

read-only

The total number of octets contained in the valid frames that have been received on the ports in this group. This counter is the summation of the values of the rptrMonitorPortReadableOctets counters for all of the ports in the group. This statistic provides an indicator of the total data transferred. The approximate minimum time for rollover of this counter is 58 minutes.

rptrMonitorPackage

1.3.6.1.2.1.22.2

CTR rptrMonitorPortAlignmentErrors

1.3.6.1.2.1.22.2.3.1.1.6

Counter

read-only

This counter is incremented by one for each frame received on this port with the FCSError and FramingError signals asserted and CollisionEvent signal deasserted and whose OctetCount is greater than or equal to minFrameSize and less than or equal to maxFrameSize (Ref: IEEE 802.3 Std, 4.4.2.1). If rptrMonitorPortAlignmentErrors is incremented then the rptrMonitorPortFCSErrors Counter shall not be incremented for the same frame. The approximate minimum time for rollover of this counter is 80 hours.

CTR rptrMonitorPortAutoPartitions

1.3.6.1.2.1.22.2.3.1.1.14

Counter

read-only

This counter is incremented by one for each time the repeater has automatically partitioned this port. The conditions that cause port partitioning are specified in the partition state machine in Section 9 [IEEE 802.3 Std]. They are not differentiated here.

CTR rptrMonitorPortCollisions

1.3.6.1.2.1.22.2.3.1.1.10

Counter

read-only

This counter is incremented by one for any CarrierEvent signal on any port for which the CollisionEvent signal on this port is asserted. The approximate minimum time for rollover of this counter is 16 hours.

CTR rptrMonitorPortDataRateMismatches

1.3.6.1.2.1.22.2.3.1.1.13

Counter

read-only

This counter is incremented by one for each frame received on this port that meets all of the following conditions: a) The CollisionEvent signal is not asserted. b) The ActivityDuration is greater than ValidPacketMinTime. c) The frequency (data rate) is detectably mismatched from the local transmit frequency. The exact degree of mismatch is vendor specific and is to be defined by the vendor for conformance testing. When this event occurs, other counters whose increment conditions were satisfied may or may not also be incremented, at the implementor's discretion. Whether or not the repeater was able to maintain data integrity is beyond the scope of this standard.

rptrMonitorPortEntry

1.3.6.1.2.1.22.2.3.1.1

not-accessible

An entry in the table, containing performance and error statistics for a single port.

CTR rptrMonitorPortFCSErrors

1.3.6.1.2.1.22.2.3.1.1.5

Counter

read-only

This counter is incremented by one for each frame received on this port with the FCSError signal asserted and the FramingError and CollisionEvent signals deasserted and whose OctetCount is greater than or equal to minFrameSize and less than or equal to maxFrameSize (Ref: 4.4.2.1, IEEE 802.3 Std). The approximate minimum time for rollover of this counter is 80 hours.

CTR rptrMonitorPortFrameTooLongs

1.3.6.1.2.1.22.2.3.1.1.7

Counter

read-only

This counter is incremented by one for each frame received on this port whose OctetCount is greater than maxFrameSize (Ref: 4.4.2.1, IEEE 802.3 Std). If rptrMonitorPortFrameTooLongs is incremented then neither the rptrMonitorPortAlignmentErrors nor the rptrMonitorPortFCSErrors counter shall be incremented for the frame. The approximate minimum time for rollover of this counter is 61 days.

INT rptrMonitorPortGroupIndex

1.3.6.1.2.1.22.2.3.1.1.1

INTEGER

read-only

This object identifies the group containing the port for which this entry contains information.

INT rptrMonitorPortIndex

1.3.6.1.2.1.22.2.3.1.1.2

INTEGER

read-only

This object identifies the port within the group for which this entry contains information.

rptrMonitorPortInfo

1.3.6.1.2.1.22.2.3

CTR rptrMonitorPortLateEvents

1.3.6.1.2.1.22.2.3.1.1.11

Counter

read-only

This counter is incremented by one for each CarrierEvent on this port in which the CollIn(X) variable transitions to the value SQE (Ref: 9.6.6.2, IEEE 802.3 Std) while the ActivityDuration is greater than the LateEventThreshold. Such a CarrierEvent is counted twice, as both a collision and as a lateEvent. The LateEventThreshold is greater than 480 bit times and less than 565 bit times. LateEventThreshold has tolerances included to permit an implementation to build a single threshold to serve as both the LateEventThreshold and ValidPacketMinTime threshold. The approximate minimum time for rollover of this counter is 81 hours.

CTR rptrMonitorPortReadableFrames

1.3.6.1.2.1.22.2.3.1.1.3

Counter

read-only

This object is the number of frames of valid frame length that have been received on this port. This counter is incremented by one for each frame received on this port whose OctetCount is greater than or equal to minFrameSize and less than or equal to maxFrameSize (Ref: IEEE 802.3 Std, 4.4.2.1) and for which the FCSError and CollisionEvent signals are not asserted. This statistic provides one of the parameters necessary for obtaining the packet error rate. The approximate minimum time for rollover of this counter is 80 hours.

CTR rptrMonitorPortReadableOctets

1.3.6.1.2.1.22.2.3.1.1.4

Counter

read-only

This object is the number of octets contained in valid frames that have been received on this port. This counter is incremented by OctetCount for each frame received on this port which has been determined to be a readable frame. This statistic provides an indicator of the total data transferred. The approximate minimum time for rollover of this counter is 58 minutes.

CTR rptrMonitorPortRunts

1.3.6.1.2.1.22.2.3.1.1.9

Counter

read-only

This counter is incremented by one for each CarrierEvent on this port that meets one of the following two conditions. Only one test need be made. a) The ActivityDuration is greater than ShortEventMaxTime and less than ValidPacketMinTime and the CollisionEvent signal is deasserted. b) The OctetCount is less than 64, the ActivityDuration is greater than ShortEventMaxTime and the CollisionEvent signal is deasserted. ValidPacketMinTime is greater than or equal to 552 bit times and less than 565 bit times. An event whose length is greater than 74 bit times but less than 82 bit times shall increment either the shortEvents counter or the runts counter but not both. A CarrierEvent greater than or equal to 552 bit times but less than 565 bit times may or may not be counted as a runt. ValidPacketMinTime has tolerances included to provide for circuit losses between a conformance test point at the AUI and the measurement point within the state machine. Runts usually indicate collision fragments, a normal network event. In certain situations associated with large diameter networks a percentage of runts may exceed ValidPacketMinTime. The approximate minimum time for rollover of this counter is 16 hours.

CTR rptrMonitorPortShortEvents

1.3.6.1.2.1.22.2.3.1.1.8

Counter

read-only

This counter is incremented by one for each CarrierEvent on this port with ActivityDuration less than ShortEventMaxTime. ShortEventMaxTime is greater than 74 bit times and less than 82 bit times. ShortEventMaxTime has tolerances included to provide for circuit losses between a conformance test point at the AUI and the measurement point within the state machine. Note: shortEvents may indicate externally generated noise hits which will cause the repeater to transmit Runts to its other ports, or propagate a collision (which may be late) back to the transmitting DTE and damaged frames to the rest of the network. Implementors may wish to consider selecting the ShortEventMaxTime towards the lower end of the allowed tolerance range to accommodate bit losses suffered through physical channel devices not budgeted for within this standard. The approximate minimum time for rollover of this counter is 16 hours.

rptrMonitorPortTable

1.3.6.1.2.1.22.2.3.1

not-accessible

Table of performance and error statistics for the ports.

CTR rptrMonitorPortTotalErrors

1.3.6.1.2.1.22.2.3.1.1.15

Counter

read-only

The total number of errors which have occurred on this port. This counter is the summation of the values of other error counters (for the same port), namely: rptrMonitorPortFCSErrors, rptrMonitorPortAlignmentErrors, rptrMonitorPortFrameTooLongs, rptrMonitorPortShortEvents, rptrMonitorPortLateEvents, rptrMonitorPortVeryLongEvents, and rptrMonitorPortDataRateMismatches. This counter is redundant in the sense that it is the summation of information already available through other objects. However, it is included specifically because the regular retrieval of this object as a means of tracking the health of a port provides a considerable optimization of network management traffic over the otherwise necessary retrieval of the summed counters.

CTR rptrMonitorPortVeryLongEvents

1.3.6.1.2.1.22.2.3.1.1.12

Counter

read-only

This counter is incremented by one for each CarrierEvent on this port whose ActivityDuration is greater than the MAU Jabber Lockup Protection timer TW3 (Ref: 9.6.1 & 9.6.5, IEEE 802.3 Std). Other counters may be incremented as appropriate.

rptrMonitorRptrInfo

1.3.6.1.2.1.22.2.1

CTR rptrMonitorTransmitCollisions

1.3.6.1.2.1.22.2.1.1

Counter

read-only

This counter is incremented every time the repeater state machine enters the TRANSMIT COLLISION state from any state other than ONE PORT LEFT (Ref: Fig 9-2, IEEE 802.3 Std). The approximate minimum time for rollover of this counter is 16 hours.

INT rptrNonDisruptTest

1.3.6.1.2.1.22.1.1.5

INTEGER

read-write

Setting this object to selfTest(2) causes the repeater to perform a agent-specific, non- disruptive self-test that has the following characteristics: a) The nature of the tests is not specified. b) The test does not change the state of the repeater or management information about the repeater. c) The test does not inject packets onto any segment. d) The test does not prevent the relay of any packets. e) The test does not interfere with management functions. After performing this test the agent will update the repeater health information and send a rptrHealth trap. Setting this object to noSelfTest(1) has no effect. The agent will always return the value noSelfTest(1) when this object is read.

INT rptrOperStatus

1.3.6.1.2.1.22.1.1.2

INTEGER

read-only

The rptrOperStatus object indicates the operational state of the repeater. The rptrHealthText object may be consulted for more specific information about the state of the repeater's health. In the case of multiple kinds of failures (e.g., repeater failure and port failure), the value of this attribute shall reflect the highest priority failure in the following order: rptrFailure(3) groupFailure(4) portFailure(5) generalFailure(6).

INT rptrPortAdminStatus

1.3.6.1.2.1.22.1.3.1.1.3

INTEGER

read-write

Setting this object to disabled(2) disables the port. A disabled port neither transmits nor receives. Once disabled, a port must be explicitly enabled to restore operation. A port which is disabled when power is lost or when a reset is exerted shall remain disabled when normal operation resumes. The admin status takes precedence over auto- partition and functionally operates between the auto-partition mechanism and the AUI/PMA. Setting this object to enabled(1) enables the port and exerts a BEGIN on the port's auto-partition state machine. (In effect, when a port is disabled, the value of rptrPortAutoPartitionState for that port is frozen until the port is next enabled. When the port becomes enabled, the rptrPortAutoPartitionState becomes notAutoPartitioned(1), regardless of its pre-disabling state.)

INT rptrPortAutoPartitionState

1.3.6.1.2.1.22.1.3.1.1.4

INTEGER

read-only

The autoPartitionState flag indicates whether the port is currently partitioned by the repeater's auto-partition protection. The conditions that cause port partitioning are specified in partition state machine in Section 9 [IEEE 802.3 Std]. They are not differentiated here.

rptrPortEntry

1.3.6.1.2.1.22.1.3.1.1

not-accessible

An entry in the table, containing information about a single port.

INT rptrPortGroupIndex

1.3.6.1.2.1.22.1.3.1.1.1

INTEGER

read-only

This object identifies the group containing the port for which this entry contains information.

INT rptrPortIndex

1.3.6.1.2.1.22.1.3.1.1.2

INTEGER

read-only

This object identifies the port within the group for which this entry contains information. This value can never be greater than rptrGroupPortCapacity for the associated group.

rptrPortInfo

1.3.6.1.2.1.22.1.3

INT rptrPortOperStatus

1.3.6.1.2.1.22.1.3.1.1.5

INTEGER

read-only

This object indicates the port's operational status. The notPresent(3) status indicates the port is physically removed (note this may or may not be possible depending on the type of port.) The operational(1) status indicates that the port is enabled (see rptrPortAdminStatus) and working, even though it might be auto-partitioned (see rptrPortAutoPartitionState). If this object has the value operational(1) and rptrPortAdminStatus is set to disabled(2), it is expected that this object's value will change to notOperational(2) soon after.

rptrPortTable

1.3.6.1.2.1.22.1.3.1

not-accessible

Table of descriptive and status information about the ports.

INT rptrReset

1.3.6.1.2.1.22.1.1.4

INTEGER

read-write

Setting this object to reset(2) causes a transition to the START state of Fig 9-2 in section 9 [IEEE 802.3 Std]. Setting this object to noReset(1) has no effect. The agent will always return the value noReset(1) when this object is read. This action does not reset the management counters defined in this document nor does it affect the portAdminStatus parameters. Included in this action is the execution of a disruptive Self-Test with the following characteristics: a) The nature of the tests is not specified. b) The test resets the repeater but without affecting management information about the repeater. c) The test does not inject packets onto any segment. d) Packets received during the test may or may not be transferred. e) The test does not interfere with management functions. As a result of this action a rptrResetEvent trap should be sent.

NTF rptrResetEvent

1.3.6.1.2.1.22.0.3

The rptrResetEvent trap conveys information related to the operational status of the repeater. This trap is sent on completion of a repeater reset action. A repeater reset action is defined as an a transition to the START state of Fig 9-2 in section 9 [IEEE 802.3 Std], when triggered by a management command (e.g., an SNMP Set on the rptrReset object). The agent must throttle the generation of consecutive rptrResetEvent traps so that there is at least a five-second gap between them. The rptrResetEvent trap is not sent when the agent restarts and sends an SNMP coldStart or warmStart trap. However, it is recommended that a repeater agent send the rptrOperStatus object as an optional object with its coldStart and warmStart trap PDUs. The rptrOperStatus object must be included in the varbind list sent with this trap. The agent may optionally include the rptrHealthText object as well.

rptrRptrInfo

1.3.6.1.2.1.22.1.1

GAU rptrTotalPartitionedPorts

1.3.6.1.2.1.22.1.1.6

Gauge

read-only

This object returns the total number of ports in the repeater whose current state meets all three of the following criteria: rptrPortOperStatus does not have the value notPresent(3), rptrPortAdminStatus is enabled(1), and rptrPortAutoPartitionState is autoPartitioned(2).

snmp

1.3.6.1.2.1.11

snmpDot3RptrMgt

1.3.6.1.2.1.22

INT snmpEnableAuthenTraps

1.3.6.1.2.1.11.30

INTEGER

read-write

Indicates whether the SNMP agent process is permitted to generate authentication-failure traps. The value of this object overrides any configuration information; as such, it provides a means whereby all authentication-failure traps may be disabled. Note that it is strongly recommended that this object be stored in non-volatile memory so that it remains constant between re-initializations of the network management system.

CTR snmpInASNParseErrs

1.3.6.1.2.1.11.6

Counter

read-only

The total number of ASN.1 or BER errors encountered by the SNMP protocol entity when decoding received SNMP Messages.

CTR snmpInBadCommunityNames

1.3.6.1.2.1.11.4

Counter

read-only

The total number of SNMP Messages delivered to the SNMP protocol entity which used a SNMP community name not known to said entity.

CTR snmpInBadCommunityUses

1.3.6.1.2.1.11.5

Counter

read-only

The total number of SNMP Messages delivered to the SNMP protocol entity which represented an SNMP operation which was not allowed by the SNMP community named in the Message.

CTR snmpInBadValues

1.3.6.1.2.1.11.10

Counter

read-only

The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `badValue'.

CTR snmpInBadVersions

1.3.6.1.2.1.11.3

Counter

read-only

The total number of SNMP Messages which were delivered to the SNMP protocol entity and were for an unsupported SNMP version.

CTR snmpInGenErrs

1.3.6.1.2.1.11.12

Counter

read-only

The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `genErr'.

CTR snmpInGetNexts

1.3.6.1.2.1.11.16

Counter

read-only

The total number of SNMP Get-Next PDUs which have been accepted and processed by the SNMP protocol entity.

CTR snmpInGetRequests

1.3.6.1.2.1.11.15

Counter

read-only

The total number of SNMP Get-Request PDUs which have been accepted and processed by the SNMP protocol entity.

CTR snmpInGetResponses

1.3.6.1.2.1.11.18

Counter

read-only

The total number of SNMP Get-Response PDUs which have been accepted and processed by the SNMP protocol entity.

CTR snmpInNoSuchNames

1.3.6.1.2.1.11.9

Counter

read-only

The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `noSuchName'.

CTR snmpInPkts

1.3.6.1.2.1.11.1

Counter

read-only

The total number of Messages delivered to the SNMP entity from the transport service.

CTR snmpInReadOnlys

1.3.6.1.2.1.11.11

Counter

read-only

The total number valid SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `readOnly'. It should be noted that it is a protocol error to generate an SNMP PDU which contains the value `readOnly' in the error-status field, as such this object is provided as a means of detecting incorrect implementations of the SNMP.

CTR snmpInSetRequests

1.3.6.1.2.1.11.17

Counter

read-only

The total number of SNMP Set-Request PDUs which have been accepted and processed by the SNMP protocol entity.

CTR snmpInTooBigs

1.3.6.1.2.1.11.8

Counter

read-only

The total number of SNMP PDUs which were delivered to the SNMP protocol entity and for which the value of the error-status field is `tooBig'.

CTR snmpInTotalReqVars

1.3.6.1.2.1.11.13

Counter

read-only

The total number of MIB objects which have been retrieved successfully by the SNMP protocol entity as the result of receiving valid SNMP Get-Request and Get-Next PDUs.

CTR snmpInTotalSetVars

1.3.6.1.2.1.11.14

Counter

read-only

The total number of MIB objects which have been altered successfully by the SNMP protocol entity as the result of receiving valid SNMP Set-Request PDUs.

CTR snmpInTraps

1.3.6.1.2.1.11.19

Counter

read-only

The total number of SNMP Trap PDUs which have been accepted and processed by the SNMP protocol entity.

CTR snmpOutBadValues

1.3.6.1.2.1.11.22

Counter

read-only

The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `badValue'.

CTR snmpOutGenErrs

1.3.6.1.2.1.11.24

Counter

read-only

The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `genErr'.

CTR snmpOutGetNexts

1.3.6.1.2.1.11.26

Counter

read-only

The total number of SNMP Get-Next PDUs which have been generated by the SNMP protocol entity.

CTR snmpOutGetRequests

1.3.6.1.2.1.11.25

Counter

read-only

The total number of SNMP Get-Request PDUs which have been generated by the SNMP protocol entity.

CTR snmpOutGetResponses

1.3.6.1.2.1.11.28

Counter

read-only

The total number of SNMP Get-Response PDUs which have been generated by the SNMP protocol entity.

CTR snmpOutNoSuchNames

1.3.6.1.2.1.11.21

Counter

read-only

The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status is `noSuchName'.

CTR snmpOutPkts

1.3.6.1.2.1.11.2

Counter

read-only

The total number of SNMP Messages which were passed from the SNMP protocol entity to the transport service.

CTR snmpOutSetRequests

1.3.6.1.2.1.11.27

Counter

read-only

The total number of SNMP Set-Request PDUs which have been generated by the SNMP protocol entity.

CTR snmpOutTooBigs

1.3.6.1.2.1.11.20

Counter

read-only

The total number of SNMP PDUs which were generated by the SNMP protocol entity and for which the value of the error-status field is `tooBig.'

CTR snmpOutTraps

1.3.6.1.2.1.11.29

Counter

read-only

The total number of SNMP Trap PDUs which have been generated by the SNMP protocol entity.

STR sysContact

1.3.6.1.2.1.1.4

DisplayString

read-write

The textual identification of the contact person for this managed node, together with information on how to contact this person.

STR sysDescr

1.3.6.1.2.1.1.1

DisplayString

read-only

A textual description of the entity. This value should include the full name and version identification of the system's hardware type, software operating-system, and networking software. It is mandatory that this only contain printable ASCII characters.

STR sysLocation

1.3.6.1.2.1.1.6

DisplayString

read-write

The physical location of this node (e.g., `telephone closet, 3rd floor').

STR sysName

1.3.6.1.2.1.1.5

DisplayString

read-write

An administratively-assigned name for this managed node. By convention, this is the node's fully-qualified domain name.

OID sysObjectID

1.3.6.1.2.1.1.2

OBJECT IDENTIFIER

read-only

The vendor's authoritative identification of the network management subsystem contained in the entity. This value is allocated within the SMI enterprises subtree (1.3.6.1.4.1) and provides an easy and unambiguous means for determining `what kind of box' is being managed. For example, if vendor `Flintstones, Inc.' was assigned the subtree 1.3.6.1.4.1.4242, it could assign the identifier 1.3.6.1.4.1.4242.1.1 to its `Fred Router'.

INT sysServices

1.3.6.1.2.1.1.7

INTEGER

read-only

A value which indicates the set of services that this entity primarily offers. The value is a sum. This sum initially takes the value zero, Then, for each layer, L, in the range 1 through 7, that this node performs transactions for, 2 raised to (L - 1) is added to the sum. For example, a node which performs primarily routing functions would have a value of 4 (2^(3-1)). In contrast, a node which is a host offering application services would have a value of 72 (2^(4-1) + 2^(7-1)). Note that in the context of the Internet suite of protocols, values should be calculated accordingly: layer functionality 1 physical (e.g., repeaters) 2 datalink/subnetwork (e.g., bridges) 3 internet (e.g., IP gateways) 4 end-to-end (e.g., IP hosts) 7 applications (e.g., mail relays) For systems including OSI protocols, layers 5 and 6 may also be counted.

system

1.3.6.1.2.1.1

TIK sysUpTime

1.3.6.1.2.1.1.3

TimeTicks

read-only

The time (in hundredths of a second) since the network management portion of the system was last re-initialized.

tcp

1.3.6.1.2.1.6

CTR tcpActiveOpens

1.3.6.1.2.1.6.5

Counter

read-only

The number of times TCP connections have made a direct transition to the SYN-SENT state from the CLOSED state.

CTR tcpAttemptFails

1.3.6.1.2.1.6.7

Counter

read-only

The number of times TCP connections have made a direct transition to the CLOSED state from either the SYN-SENT state or the SYN-RCVD state, plus the number of times TCP connections have made a direct transition to the LISTEN state from the SYN-RCVD state.

tcpConnEntry

1.3.6.1.2.1.6.13.1

not-accessible

Information about a particular current TCP connection. An object of this type is transient, in that it ceases to exist when (or soon after) the connection makes the transition to the CLOSED state.

IP tcpConnLocalAddress

1.3.6.1.2.1.6.13.1.2

IpAddress

read-only

The local IP address for this TCP connection. In the case of a connection in the listen state which is willing to accept connections for any IP interface associated with the node, the value 0.0.0.0 is used.

INT tcpConnLocalPort

1.3.6.1.2.1.6.13.1.3

INTEGER

read-only

The local port number for this TCP connection.

IP tcpConnRemAddress

1.3.6.1.2.1.6.13.1.4

IpAddress

read-only

The remote IP address for this TCP connection.

INT tcpConnRemPort

1.3.6.1.2.1.6.13.1.5

INTEGER

read-only

The remote port number for this TCP connection.

INT tcpConnState

1.3.6.1.2.1.6.13.1.1

INTEGER

read-write

The state of this TCP connection. The only value which may be set by a management station is deleteTCB(12). Accordingly, it is appropriate for an agent to return a `badValue' response if a management station attempts to set this object to any other value. If a management station sets this object to the value deleteTCB(12), then this has the effect of deleting the TCB (as defined in RFC 793) of the corresponding connection on the managed node, resulting in immediate termination of the connection. As an implementation-specific option, a RST segment may be sent from the managed node to the other TCP endpoint (note however that RST segments are not sent reliably).

tcpConnTable

1.3.6.1.2.1.6.13

not-accessible

A table containing TCP connection-specific information.

GAU tcpCurrEstab

1.3.6.1.2.1.6.9

Gauge

read-only

The number of TCP connections for which the current state is either ESTABLISHED or CLOSE- WAIT.

CTR tcpEstabResets

1.3.6.1.2.1.6.8

Counter

read-only

The number of times TCP connections have made a direct transition to the CLOSED state from either the ESTABLISHED state or the CLOSE-WAIT state.

CTR tcpInErrs

1.3.6.1.2.1.6.14

Counter

read-only

The total number of segments received in error (e.g., bad TCP checksums).

CTR tcpInSegs

1.3.6.1.2.1.6.10

Counter

read-only

The total number of segments received, including those received in error. This count includes segments received on currently established connections.

INT tcpMaxConn

1.3.6.1.2.1.6.4

INTEGER

read-only

The limit on the total number of TCP connections the entity can support. In entities where the maximum number of connections is dynamic, this object should contain the value -1.

CTR tcpOutRsts

1.3.6.1.2.1.6.15

Counter

read-only

The number of TCP segments sent containing the RST flag.

CTR tcpOutSegs

1.3.6.1.2.1.6.11

Counter

read-only

The total number of segments sent, including those on current connections but excluding those containing only retransmitted octets.

CTR tcpPassiveOpens

1.3.6.1.2.1.6.6

Counter

read-only

The number of times TCP connections have made a direct transition to the SYN-RCVD state from the LISTEN state.

CTR tcpRetransSegs

1.3.6.1.2.1.6.12

Counter

read-only

The total number of segments retransmitted - that is, the number of TCP segments transmitted containing one or more previously transmitted octets.

INT tcpRtoAlgorithm

1.3.6.1.2.1.6.1

INTEGER

read-only

The algorithm used to determine the timeout value used for retransmitting unacknowledged octets.

INT tcpRtoMax

1.3.6.1.2.1.6.3

INTEGER

read-only

The maximum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the UBOUND quantity described in RFC 793.

INT tcpRtoMin

1.3.6.1.2.1.6.2

INTEGER

read-only

The minimum value permitted by a TCP implementation for the retransmission timeout, measured in milliseconds. More refined semantics for objects of this type depend upon the algorithm used to determine the retransmission timeout. In particular, when the timeout algorithm is rsre(3), an object of this type has the semantics of the LBOUND quantity described in RFC 793.

NTF topologyChange

1.3.6.1.2.1.17.0.2

A topologyChange trap is sent by a bridge when any of its configured ports transitions from the Learning state to the Forwarding state, or from the Forwarding state to the Blocking state. The trap is not sent if a newRoot trap is sent for the same transition.

transmission

1.3.6.1.2.1.10

udp

1.3.6.1.2.1.7

udpEntry

1.3.6.1.2.1.7.5.1

not-accessible

Information about a particular current UDP listener.

CTR udpInDatagrams

1.3.6.1.2.1.7.1

Counter

read-only

The total number of UDP datagrams delivered to UDP users.

CTR udpInErrors

1.3.6.1.2.1.7.3

Counter

read-only

The number of received UDP datagrams that could not be delivered for reasons other than the lack of an application at the destination port.

IP udpLocalAddress

1.3.6.1.2.1.7.5.1.1

IpAddress

read-only

The local IP address for this UDP listener. In the case of a UDP listener which is willing to accept datagrams for any IP interface associated with the node, the value 0.0.0.0 is used.

INT udpLocalPort

1.3.6.1.2.1.7.5.1.2

INTEGER

read-only

The local port number for this UDP listener.

CTR udpNoPorts

1.3.6.1.2.1.7.2

Counter

read-only

The total number of received UDP datagrams for which there was no application at the destination port.

CTR udpOutDatagrams

1.3.6.1.2.1.7.4

Counter

read-only

The total number of UDP datagrams sent from this entity.

udpTable

1.3.6.1.2.1.7.5

not-accessible

A table containing UDP listener information.

What Is LANART-AGENT?

Supported Devices

Monitoring Examples

What Can Be Monitored

RFC description

LANART-AGENT

What Is LANART-AGENT?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description