CISCO-FRAME-RELAY-MIB

All MIBs › CISCO-FRAME-RELAY-MIB

Organization: Cisco Systems, Inc.

Last Updated: 2000-10-13

Category: Cisco Devices, Frame Relay, Network Interfaces

Description: Provides management objects for Frame Relay interface operations on Cisco devices.

IPNetwork Monitor uses several OIDs from this MIB in network discovery and polling the applicable devices. Start monitoring CISCO-FRAME-RELAY-MIB with a free 30-day trial of IPNetwork Monitor.

What Is CISCO-FRAME-RELAY-MIB?

CISCO-FRAME-RELAY-MIB is a Cisco proprietary MIB providing management objects for Frame Relay WAN interfaces on Cisco routers, covering the Local Management Interface (LMI) protocol used between a Frame Relay DTE and the service-provider network as well as per-circuit configuration objects. It exposes LMI link status and type, counts of LMI status-enquiry and status messages sent/received, and counters for LMI update-status exchanges and timeouts, alongside a separate group of Frame Relay circuit objects. Its monitoring purpose centers on WAN link operational health: administrators track cfrLmiLinkstatus to confirm the Frame Relay link is up and correctly signaling, and watch LMI timeout counters to detect keepalive failures that typically precede or explain a Frame Relay circuit going down. As a legacy WAN technology MIB it is a Cisco-specific implementation for Cisco IOS Frame Relay interfaces rather than a direct dependency of other standard MIBs. It is deployed on older Cisco routers still running Frame Relay WAN links, common in legacy enterprise branch connectivity before migration to MPLS/Ethernet WAN. Engineers can download the CISCO-FRAME-RELAY-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-FRAME-RELAY-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco routers with Frame Relay WAN interfaces

Monitoring Examples

A WAN operations team would poll cfrLmiTable/cfrLmiEntry to check cfrLmiLinkstatus and cfrLmiLinkType on a serial interface, confirming the Frame Relay LMI protocol is correctly negotiated. Tracking cfrLmiStatusIns/cfrLmiStatusOuts alongside cfrLmiStatusTimeouts over time would reveal intermittent LMI keepalive loss, a leading indicator of an unreliable carrier circuit before a full outage occurs. The cfrLmiEnquiryIns/cfrLmiEnquiryOuts counters help confirm the polling cadence between router and Frame Relay switch is functioning as configured.

What Can Be Monitored

LMI link status
LMI protocol type
LMI status enquiry/response counts
LMI status timeouts
Frame Relay circuit status

Imported Objects

From CISCO-SMI

ciscoMgmt

OBJECT-IDENTITY

From IF-MIB

InterfaceIndex

From RFC1213-MIB

ifIndex

From RFC1315-MIB

frCircuitDlci	OBJECT-TYPE
frCircuitEntry	OBJECT-TYPE
frCircuitIfIndex	OBJECT-TYPE
frDlcmiEntry	OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using cfrLmiEnquiryIns OID:

Select a Cisco router as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type cfrLmiEnquiryIns into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the number of Status Enquiry messages received. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline (in messages), since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
C32 cfrCircuitDEins	1.3.6.1.4.1.9.9.49.1.2.1.1.1	Counter32	read-only	Number of packets received with the Discarded Eligibility indictor (the DE bit) set.
C32 cfrCircuitDEouts	1.3.6.1.4.1.9.9.49.1.2.1.1.2	Counter32	read-only	Number of packets transmitted with DE bit set.
C32 cfrCircuitDropPktsOuts	1.3.6.1.4.1.9.9.49.1.2.1.1.3	Counter32	read-only	Number of discarded packets that were to be sent.
cfrCircuitEntry	1.3.6.1.4.1.9.9.49.1.2.1.1		not-accessible	Each entry of the table contains information of a circuit that are not included in frCircuitTable of RFC1315 but are generic to Frame Relay.
cfrCircuitObjs	1.3.6.1.4.1.9.9.49.1.2
cfrCircuitTable	1.3.6.1.4.1.9.9.49.1.2.1		not-accessible	Table of descriptive and statistics information that are generic to Frame Relay virtual circuits.
INT cfrCircuitType	1.3.6.1.4.1.9.9.49.1.2.1.1.4	INTEGER	read-only	Basic circuit type
INT cfrConnClpBit	1.3.6.1.4.1.9.9.49.1.7.1.1.14	INTEGER	read-only	The method of operation used to map loss priority mapping in the FR to ATM direction. Not supported in case of FR-FR connection.
INT cfrConnDeBit	1.3.6.1.4.1.9.9.49.1.7.1.1.13	INTEGER	read-only	The method of operation for loss priority mapping in the B-ISDN to FR direction.. Not supported in case of FR-FR connection.
cfrConnectionEntry	1.3.6.1.4.1.9.9.49.1.7.1.1		not-accessible	Each entry of the table contains information of a connection that is established for Frame Relay/Frame Relay and Frame Relay/ATM Network/Service Interworking.
cfrConnectionObjs	1.3.6.1.4.1.9.9.49.1.7
cfrConnectionTable	1.3.6.1.4.1.9.9.49.1.7.1		not-accessible	Table of Frame Relay/Frame Relay and Frame Relay/ATM Network/Service Interworking connection information. These are specific to Cisco's implementation.
INT cfrConnEfciBit	1.3.6.1.4.1.9.9.49.1.7.1.1.12	INTEGER	read-only	Shows whether the FECN field in the FR frame is mapped to the ATM EFCI field of every cell generated out of the FR frame. This is used to indicate congestion in FR to ATM direction in case of Frame Relay/ATM Service PVC Interworking. Not supported in FRF.5 (Frame Relay/ATM Network Interworking and FR-FR connections.
DLC cfrConnFrSscsDlci	1.3.6.1.4.1.9.9.49.1.7.1.1.11	DlciNumber	read-only	The DLCI value used at the FR-SSCS layer. This is one of connection multiplexing methods used in Frame Relay/ATM Network Interworking. Not supported in case of FRF.8 (FR-ATM Service PVC Interworking) and FR-FR connections
INT cfrConnID	1.3.6.1.4.1.9.9.49.1.7.1.1.2	INTEGER	read-only	The numerical identifier of a FR/FR or FR/ATM Network/Service Interworking connection.
STR cfrConnName	1.3.6.1.4.1.9.9.49.1.7.1.1.1	DisplayString	read-only	The textual name of a for FR/FR or FR/ATM Network/Service Interworking connection.
DLC cfrConnSegment1Dlci	1.3.6.1.4.1.9.9.49.1.7.1.1.6	DlciNumber	read-only	The DLCI used as the first segment of a FR-FR or FR-ATM Network/Service Interworking connection.
STR cfrConnSegment1Name	1.3.6.1.4.1.9.9.49.1.7.1.1.4	DisplayString	read-only	The textual name used to identify the first segment of a FR/FR or FR/ATM Network/Service Interworking connection.
STR cfrConnSegment1VCGroup	1.3.6.1.4.1.9.9.49.1.7.1.1.5	DisplayString	read-only	The textual name used to identify the VC-Group in the first segment of a Frame Relay/ATM Network Interworking (FRF.5)connection. This field is not applicabe in case of, FRF.8 (Frame Relay/ATM Service Interworking) and FR-FR connectione.
STR cfrConnSegment2Name	1.3.6.1.4.1.9.9.49.1.7.1.1.7	DisplayString	read-only	The interface on which second segment of a FR-FR or FR-ATM Network/Service Interworking connection is configured.
INT cfrConnSegment2Vci	1.3.6.1.4.1.9.9.49.1.7.1.1.9	INTEGER	read-only	The value of VCI, in the ATM connection, used as the second segment of a FR-ATM Network/Service Interworking connection. In case of FR-FR connection, this is not supported.
INT cfrConnSegment2Vpi	1.3.6.1.4.1.9.9.49.1.7.1.1.8	INTEGER	read-only	The value of VPI, in the ATM connection, used as the second segment of a FR-ATM Network/Service Interworking connection. In case of FR-FR connection, the same will be used to display the DLCI used as the second segment.
INT cfrConnServiceTranslation	1.3.6.1.4.1.9.9.49.1.7.1.1.10	INTEGER	read-only	Shows whether Service Translation Mode is supported or not. Translation Mode is the interworking of internetworking (routed and/or bridged) protocols used in FR-ATM Service PVC Interworking(FRF.8). This is not supported in case of FRF.5 (FR-ATM network Interworking) and FR-FR connections.
STR cfrConnState	1.3.6.1.4.1.9.9.49.1.7.1.1.3	DisplayString	read-only	Status of a FR/FR or FR/ATM Network/Service Interworking connection.
INT cfrElmiArStatus	1.3.6.1.4.1.9.9.49.1.5.2.1.2	INTEGER	read-only	This variable states whether the Enhanced Link Management Interface(ELMI) address registration(AR) mechanism is enabled or not on a frame relay interface. A value of 1 indicates ELMI AR is supported on the interface. A value of 2 indicates ELMI AR is supported but the user disabled the exchange of IP address and ifIndex with the neighboring device. This object doesn't have any significance if cfrElmiLinkStatus is disabled on the interface.
cfrElmiEntry	1.3.6.1.4.1.9.9.49.1.5.2.1		not-accessible	Each entry of the table contains information about a physical interface. The table can be accessible only if the device supports ELMI protocol and if LMI is enabled on the interface.
IP cfrElmiIpAddr	1.3.6.1.4.1.9.9.49.1.5.1	IpAddress	read-only	This object represents the Management address of the device used for address registration. Network management station can send management messages to this IP address. This can be user configured address or the address of one of the interfaces on the device. If address registration is disabled then this will have a value of 0.0.0.0. This object is accessible only if the ELMI protocol is supported on the device
INT cfrElmiLinkStatus	1.3.6.1.4.1.9.9.49.1.5.2.1.1	INTEGER	read-only	This variable states whether Enhanced Link Management Interface(ELMI) protocol is enabled or not on a frame relay interface.
INT cfrElmiNeighborArStatus	1.3.6.1.4.1.9.9.49.1.5.3.1.1	INTEGER	read-only	This variable indicates the status of ELMI Address registration(AR) on the neighboring device. A value of 1 indicates ELMI AR is not supported on the neighboring device. A value of 2 indicates ELMI AR is enabled on the interface. A value of 3 indicates AR is supported, but user disabled the exchange of IP address and ifIndex with the neighbor.
STR cfrElmiNeighborDeviceName	1.3.6.1.4.1.9.9.49.1.5.3.1.6	DisplayString	read-only	Device name of the neighboring device to which the other end of this interface is connected.
cfrElmiNeighborEntry	1.3.6.1.4.1.9.9.49.1.5.3.1		not-accessible	Each entry of the table contains information of the neighboring device connected to a physical interface. The entry will be present only if ELMI is enabled on the neighboring device interface. If the value of the cfrElmiRemoteStatus in the cfrElmiEntry is 1 then a valid entry exists for the interface. If ELMI is not supported on the remote end then, the neighbor information for the interface will not be present
NUM cfrElmiNeighborIfIndex	1.3.6.1.4.1.9.9.49.1.5.3.1.3	InterfaceIndex	read-only	The Interface index of the neighboring device to which this interface is connected. If the value of cfrElmiNeighborArStatus is 2 then this will have a valid value. If the value of cfrElmiNeighborArStatus is 3 or 1 then value of this object will be 0. NMS uses this object in the topology discovery of the network.
IP cfrElmiNeighborIpAddress	1.3.6.1.4.1.9.9.49.1.5.3.1.2	IpAddress	read-only	The Management IP address of the neighboring device to which the other end of this interface is connected. Network management system can use this address to send management messages to the device. If address registration is not supported on the remote end then the value will be 0.0.0.0. NMS uses this object in the topology discovery of the network.
STR cfrElmiNeighborPlatformName	1.3.6.1.4.1.9.9.49.1.5.3.1.5	DisplayString	read-only	Platform name of the neighboring device to which the other end of this interface is connected.
cfrElmiNeighborTable	1.3.6.1.4.1.9.9.49.1.5.3		not-accessible	Table of CISCO Frame Relay Neighbor ELMI information that is specific to CISCO implementation.
STR cfrElmiNeighborVendorName	1.3.6.1.4.1.9.9.49.1.5.3.1.4	DisplayString	read-only	Vendor name of the neighboring device to which the other end of this interface is connected.
cfrElmiObjs	1.3.6.1.4.1.9.9.49.1.5
INT cfrElmiRemoteStatus	1.3.6.1.4.1.9.9.49.1.5.2.1.3	INTEGER	read-only	This variable states the Enhanced Link Management(ELMI) status on the other end of the interface. If cfrElmiLinkStatus is enabled on the other end a value of 1 will be returned, else 2 will be returned. This object doesn't have any significance if cfrElmiLinkStatus is disabled on the interface
cfrElmiTable	1.3.6.1.4.1.9.9.49.1.5.2		not-accessible	Table of CISCO Frame Relay ELMI information that is specific to CISCO implementation
I32 cfrExtCircuitBandwidth	1.3.6.1.4.1.9.9.49.1.2.2.1.17	Integer32	read-only	Bandwidth of the virtual circuit, acquired from Cisco typed LMI Full Status message.
C32 cfrExtCircuitBcastByteOuts	1.3.6.1.4.1.9.9.49.1.2.2.1.16	Counter32	read-only	Total number of bytes sent out to the network in broadcast packets.
C32 cfrExtCircuitBcastPktOuts	1.3.6.1.4.1.9.9.49.1.2.2.1.15	Counter32	read-only	Total number of broadcast packets sent out to the network.
C32 cfrExtCircuitBECNOuts	1.3.6.1.4.1.9.9.49.1.2.2.1.12	Counter32	read-only	Total number of frames sent out to the network indicating backward congestion.
INT cfrExtCircuitCreateType	1.3.6.1.4.1.9.9.49.1.2.2.1.5	INTEGER	read-only	Identify the last source of the circuit's creation.
cfrExtCircuitEntry	1.3.6.1.4.1.9.9.49.1.2.2.1		not-accessible	Each entry of the table contains information of a Frame Relay virtual circuit that are specific to Cisco implementation.
C32 cfrExtCircuitFECNOuts	1.3.6.1.4.1.9.9.49.1.2.2.1.11	Counter32	read-only	Total number of frames sent out to the network indicating forward congestion.
STR cfrExtCircuitIfName	1.3.6.1.4.1.9.9.49.1.2.2.1.1	DisplayString	read-only	The textual name of the main interface or the subinterface that this DLCI is associated with. This is the same name string of an interface used in the configuration and all console displays, such as 'serial 0', 'serial 3/0.3', etc.
INT cfrExtCircuitIfType	1.3.6.1.4.1.9.9.49.1.2.2.1.2	INTEGER	read-only	Type of the subinterface this DLCI is associated with, if configured.
INT cfrExtCircuitMapStatus	1.3.6.1.4.1.9.9.49.1.2.2.1.4	INTEGER	read-only	The mapping protocols (internally considered as the 'link type') applied on this circuit. The value ranges from 0 to 2047. For point-to-point DLCI, the value stays zero. Otherwise, the value is a sum. It initially takes the value zero, then, for each type of Protocol, 2 raised to a power is added to the sum. The following table presents respective power and equivalent value for each applicable type: Protocol Power Value -------- ----- ----- IP 0 1 IPX 1 2 Appletalk 2 4 XNS 3 8 VINES 4 16 DECnet 5 32 CLNS 6 64 Bridging 7 128 RSRB 8 256 STUN 9 512 LLC2 10 1024 For example, value 3 means the circuit's mapping protocols include IP and IPX. (3 = 21 + 20, where 0 corresponds to IP and 1 to IPX.) Value 0 means there is currently no mapping protocol for the circuit. See cfrMapTable for more mapping information.
I32 cfrExtCircuitMinThruputIn	1.3.6.1.4.1.9.9.49.1.2.2.1.14	Integer32	read-only	Circuit's incoming minimal Throughput based on configuration.
I32 cfrExtCircuitMinThruputOut	1.3.6.1.4.1.9.9.49.1.2.2.1.13	Integer32	read-only	Circuit's outgoing minimal Throughput based on configuration.
T/F cfrExtCircuitMulticast	1.3.6.1.4.1.9.9.49.1.2.2.1.6	TruthValue	read-only	Indicate if this DLCI is a multicast DLCI.
INT cfrExtCircuitRcvDataRate	1.3.6.1.4.1.9.9.49.1.2.2.1.29	INTEGER	read-only	The average rate (bytes/second) at which data is received in this circuit.
INT cfrExtCircuitRcvPktRate	1.3.6.1.4.1.9.9.49.1.2.2.1.30	INTEGER	read-only	The average number of packets received in a second in this circuit.
DLC cfrExtCircuitRoutedDlci	1.3.6.1.4.1.9.9.49.1.2.2.1.7	DlciNumber	read-only	The routed DLCI to pair up with this DLCI for switching function. NOTE: Value zero (0) indicates that there is no such routed DLCI corresponding to this DLCI.
NUM cfrExtCircuitRoutedIf	1.3.6.1.4.1.9.9.49.1.2.2.1.8	InterfaceIndex	read-only	The interface for the routed DLCI that pairs up with this DLCI for switching. Value greater than 0 is the InterfaceIndex for that interface. Value zero (0) indicates that there is no such routed DLCI corresponding to this DLCI.
T/F cfrExtCircuitShapeActive	1.3.6.1.4.1.9.9.49.1.2.2.1.25	TruthValue	read-only	Shows whether shaping is active or not.
INT cfrExtCircuitShapeAdapting	1.3.6.1.4.1.9.9.49.1.2.2.1.26	INTEGER	read-only	Type of Adaptive Shaping configured. none(1) - No adaptive shaping configured becn(2) - Backward Explicit Congestion Notification foreSight(3) - ForeSight is the network traffic control software used in Cisco WAN switches
I32 cfrExtCircuitShapeByteIncrement	1.3.6.1.4.1.9.9.49.1.2.2.1.20	Integer32	read-only	Number of tokens added into the token bucket per time interval in case of traffic shaping.
I32 cfrExtCircuitShapeByteLimit	1.3.6.1.4.1.9.9.49.1.2.2.1.18	Integer32	read-only	Maximum number of tokens a token bucket can hold in any time interval in case of traffic shaping.
C32 cfrExtCircuitShapeBytes	1.3.6.1.4.1.9.9.49.1.2.2.1.22	Counter32	read-only	Total number of bytes that went through traffic shaping.
C32 cfrExtCircuitShapeBytesDelay	1.3.6.1.4.1.9.9.49.1.2.2.1.24	Counter32	read-only	Total number of bytes that were delayed by the traffic shaper.
I32 cfrExtCircuitShapeInterval	1.3.6.1.4.1.9.9.49.1.2.2.1.19	Integer32	read-only	Committed rate measurement interval.
C32 cfrExtCircuitShapePkts	1.3.6.1.4.1.9.9.49.1.2.2.1.21	Counter32	read-only	Total number of packets that went through traffic shaping.
C32 cfrExtCircuitShapePktsDelay	1.3.6.1.4.1.9.9.49.1.2.2.1.23	Counter32	read-only	Total number of packets that were delayed by the traffic shaper.
NUM cfrExtCircuitSubifIndex	1.3.6.1.4.1.9.9.49.1.2.2.1.3	InterfaceIndex	read-only	For value greater than zero (0), it indicates the network management interface index for the subinterface associated with this DLCI. Value 0 means the DLCI is not associated with any subinterface.
cfrExtCircuitTable	1.3.6.1.4.1.9.9.49.1.2.2		not-accessible	Table of Cisco implementation specific FR circuit information. This is a Cisco extension for the frCircuitTable of RFC 1315.
INT cfrExtCircuitTxDataRate	1.3.6.1.4.1.9.9.49.1.2.2.1.27	INTEGER	read-only	The average rate (bytes/second) at which data is transmitted in this circuit.
INT cfrExtCircuitTxPktRate	1.3.6.1.4.1.9.9.49.1.2.2.1.28	INTEGER	read-only	The average number of packets sent in a second in this circuit.
C32 cfrExtCircuitUncompressIns	1.3.6.1.4.1.9.9.49.1.2.2.1.9	Counter32	read-only	Number of inbound octets of the data packets, accounted at Frame Relay level after FRF.9 payload decompression is applied. In the case of non-FRF.9, this value could be identical to frCircuitReceivedOctets, unless otherwise noted.
C32 cfrExtCircuitUncompressOuts	1.3.6.1.4.1.9.9.49.1.2.2.1.10	Counter32	read-only	Number of outbound octets of the data packets, accounted at Frame Relay level before FRF.9 payload compression is applied. In the case of non-FRF.9, this value could be identical to frCircuitSentOctets, unless otherwise noted.
C32 cfrFragAssembledInOctets	1.3.6.1.4.1.9.9.49.1.6.1.1.12	Counter32	read-only	Total number of bytes received in fully reassembled frames. It also counts the number of packets received without FR fragmentation header (i.e.in un-fragmentated pkts).
C32 cfrFragAssembledInPkts	1.3.6.1.4.1.9.9.49.1.6.1.1.11	Counter32	read-only	Total number of fully reassembled frames. It also counts the number of packets received without FR fragmentation header (i.e. in un-fragmentated pkts).
C32 cfrFragDroppedFragmentedOutPkts	1.3.6.1.4.1.9.9.49.1.6.1.1.16	Counter32	read-only	Number of fragments dropped because of running out of memory.
C32 cfrFragDroppedReAssembledInPkts	1.3.6.1.4.1.9.9.49.1.6.1.1.15	Counter32	read-only	Number of received fragments dropped for reasons such as : running out of memory, receiving segments out of sequence, receiving an unexpected frame with a B bit set, timing out on a reassembling frame.
cfrFragEntry	1.3.6.1.4.1.9.9.49.1.6.1.1		not-accessible	Each entry of the table contains details of fragmentation configured on this circuit.
C32 cfrFragInOctets	1.3.6.1.4.1.9.9.49.1.6.1.1.5	Counter32	read-only	Total number of bytes received in frames that have a fragmentation header. The number of bytes include the FR header.
C32 cfrFragInPkts	1.3.6.1.4.1.9.9.49.1.6.1.1.3	Counter32	read-only	Total number of frames received that have a fragmentation header.
C32 cfrFragInterleavedOutPkts	1.3.6.1.4.1.9.9.49.1.6.1.1.21	Counter32	read-only	Number of packets that have been interleaved between segments.
C32 cfrFragNotInOctets	1.3.6.1.4.1.9.9.49.1.6.1.1.9	Counter32	read-only	Total number of bytes received in frames that do not require reassembly and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set.
C32 cfrFragNotInPkts	1.3.6.1.4.1.9.9.49.1.6.1.1.7	Counter32	read-only	Total number of frames received that do not require reassembly and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set.
C32 cfrFragNotOutOctets	1.3.6.1.4.1.9.9.49.1.6.1.1.10	Counter32	read-only	Total number of bytes transmitted in frames that are not fragmented and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set.
C32 cfrFragNotOutPkts	1.3.6.1.4.1.9.9.49.1.6.1.1.8	Counter32	read-only	Total number of frames transmitted without fragmenting and therefore will not contain the fragmentation header. This counter is valid only when end-to-end fragmentation type is set.
cfrFragObjs	1.3.6.1.4.1.9.9.49.1.6
C32 cfrFragOutOctets	1.3.6.1.4.1.9.9.49.1.6.1.1.6	Counter32	read-only	Total number of bytes that are transmitted in frames with a fragmenation header. The number of bytes also includes the FR header.
C32 cfrFragOutOfSeqFragPkts	1.3.6.1.4.1.9.9.49.1.6.1.1.18	Counter32	read-only	Indicates the total number of packets received with an unexpected sequence number. All fragments being reassembled are dropped. Start a new packet with the received segment only if the B bit is set on the segment. Otherwise the new segment is also dropped.
C32 cfrFragOutPkts	1.3.6.1.4.1.9.9.49.1.6.1.1.4	Counter32	read-only	Total number of fragments that are transmitted with a fragmenation header.
C32 cfrFragPreOutOctets	1.3.6.1.4.1.9.9.49.1.6.1.1.14	Counter32	read-only	Total number of bytes transmitted in fragmented frames. It also counts the number of bytes trasmitted in frames without FR fragmentation header (i.e. in un-fragmentated pkts).
C32 cfrFragPreOutPkts	1.3.6.1.4.1.9.9.49.1.6.1.1.13	Counter32	read-only	Total number of frames fragmented and trasmitted. It also counts the number of packets trasmitted without FR fragmentation header (i.e. in un-fragmentated pkts).
C32 cfrFragSeqMissedPkts	1.3.6.1.4.1.9.9.49.1.6.1.1.20	Counter32	read-only	Number of fragments received in this circuit with skipped sequence number.
INT cfrFragSize	1.3.6.1.4.1.9.9.49.1.6.1.1.1	INTEGER	read-only	cfrFragSize defines the payload size of a fragment and it excludes the FR headers and any FR fragmentation header.
cfrFragTable	1.3.6.1.4.1.9.9.49.1.6.1		not-accessible	Table of Frame Relay Fragmentation information. These are specific to Cisco's implementation.
INT cfrFragTimeoutsIn	1.3.6.1.4.1.9.9.49.1.6.1.1.17	INTEGER	read-only	Number of reassemble timer timeouts for this circuit. A frame requiring more than two minutes to fully reassemble is dropped and timeout will be incremented by one.
STR cfrFragType	1.3.6.1.4.1.9.9.49.1.6.1.1.2	DisplayString	read-only	Fragmentation type configured by the user. The types supported are end-to-end, VoFR-cisco and VoFR.
C32 cfrFragUnexpectedBBitSetPkts	1.3.6.1.4.1.9.9.49.1.6.1.1.19	Counter32	read-only	Number of fragments received in this circuit with a B bit set. All fragments being reassembled are dropped and a new packet is started with this segment.
C32 cfrLmiEnquiryInsEx	1.3.6.1.4.1.9.9.49.1.1.1.1.3	Counter32	read-only	Number of Status Enquiry messages received.
C32 cfrLmiEnquiryOuts	1.3.6.1.4.1.9.9.49.1.1.1.1.4	Counter32	read-only	Number of Status Enquiry messages sent.
cfrLmiEntry	1.3.6.1.4.1.9.9.49.1.1.1.1		not-accessible	Each entry of the table contains information of Frame Relay LMI over one physical interface. They are mostly FR generic and some Cisco specific.
INT cfrLmiLinkstatus	1.3.6.1.4.1.9.9.49.1.1.1.1.1	INTEGER	read-only	Data link status via LMI.
INT cfrLmiLinkType	1.3.6.1.4.1.9.9.49.1.1.1.1.2	INTEGER	read-only	Frame Relay link type.
INT cfrLmiN392Dce	1.3.6.1.4.1.9.9.49.1.1.1.1.11	INTEGER	read-only	LMI error threshold for DCE interface. For DTE, value becomes 0.
INT cfrLmiN393Dce	1.3.6.1.4.1.9.9.49.1.1.1.1.12	INTEGER	read-only	LMI monitored event count for DCE interface. For DTE, value becomes zero (0).
cfrLmiObjs	1.3.6.1.4.1.9.9.49.1.1
C32 cfrLmiStatusEnqTimeouts	1.3.6.1.4.1.9.9.49.1.1.1.1.10	Counter32	read-only	Number of times when timeout occurred on waiting for Status Enquiry message
C32 cfrLmiStatusIns	1.3.6.1.4.1.9.9.49.1.1.1.1.5	Counter32	read-only	Number of Status messages received.
C32 cfrLmiStatusOuts	1.3.6.1.4.1.9.9.49.1.1.1.1.6	Counter32	read-only	Number of Status messages sent.
C32 cfrLmiStatusTimeouts	1.3.6.1.4.1.9.9.49.1.1.1.1.9	Counter32	read-only	Number of times when timeout occurred on waiting for Status message
INT cfrLmiT392Dce	1.3.6.1.4.1.9.9.49.1.1.1.1.13	INTEGER	read-only	DCE polling verification timer for DCE interface For DTE, the value becomes zero (0).
cfrLmiTable	1.3.6.1.4.1.9.9.49.1.1.1		not-accessible	Table of Frame Relay LMI information that are either supplemental to the frDlcmiTable of RFC 1315 or specific to Cisco's implementation.
C32 cfrLmiUpdateStatusIns	1.3.6.1.4.1.9.9.49.1.1.1.1.7	Counter32	read-only	Number of Update Status messages received.
C32 cfrLmiUpdateStatusOuts	1.3.6.1.4.1.9.9.49.1.1.1.1.8	Counter32	read-only	Number of Update Status messages sent
OCT cfrMapAddress	1.3.6.1.4.1.9.9.49.1.3.1.1.3	OCTET STRING	read-only	Mapping protocol address at remote end for this DLCI. NOTE: For point-to-point DLCI, the string is fixed to be point-to-point.
T/F cfrMapBroadcast	1.3.6.1.4.1.9.9.49.1.3.1.1.6	TruthValue	read-only	Broadcast enabled or disabled.
INT cfrMapEncaps	1.3.6.1.4.1.9.9.49.1.3.1.1.5	INTEGER	read-only	Indication of the encapsulation type for this mapping protocol.
cfrMapEntry	1.3.6.1.4.1.9.9.49.1.3.1.1		not-accessible	Each entry of the table contains one mapping information of a Frame Relay virtual circuit.
INT cfrMapIndex	1.3.6.1.4.1.9.9.49.1.3.1.1.1	INTEGER	read-only	An arbitrary Index to the mapping information associated with a certain circuit. The maximum value is arbitrarily picked which is considered sufficient for usual configuration.
cfrMapObjs	1.3.6.1.4.1.9.9.49.1.3
T/F cfrMapPayloadCompress	1.3.6.1.4.1.9.9.49.1.3.1.1.7	TruthValue	read-only	Indicate if payload compression is enabled.
INT cfrMapPayloadCompressType	1.3.6.1.4.1.9.9.49.1.3.1.1.10	INTEGER	read-only	FR payload compression type, if applicable. FRF.9 is the Frame Relay Forum Implementation Agreement on FR payload compression. The compression can be done by either software or hardware (when equipped with the supporting hardware), depending on configuration.
CFR cfrMapProtocol	1.3.6.1.4.1.9.9.49.1.3.1.1.2	CfrMapProtocols	read-only	Mapping protocol for this circuit.
INT cfrMapRtpHdrCompress	1.3.6.1.4.1.9.9.49.1.3.1.1.9	INTEGER	read-only	RTP header compression type, if applicable. The value 'passive' means that the header of an outgoing RTP/IP packet is compressed only if an incoming RTP/IP packet had a compressed header. The value 'active' means the header of every outgoing RTP/IP packet is compressed.
cfrMapTable	1.3.6.1.4.1.9.9.49.1.3.1		not-accessible	Table of protocols and addresses mapping information of FR virtual circuit.
INT cfrMapTcpHdrCompress	1.3.6.1.4.1.9.9.49.1.3.1.1.8	INTEGER	read-only	TCP header compression type, if applicable.
INT cfrMapType	1.3.6.1.4.1.9.9.49.1.3.1.1.4	INTEGER	read-only	Type for the map creation.
OCT cfrSvcAddrLocal	1.3.6.1.4.1.9.9.49.1.4.1.1.1	OCTET STRING	read-only	Local E.164/X.125 address for the circuit.
OCT cfrSvcAddrRemote	1.3.6.1.4.1.9.9.49.1.4.1.1.2	OCTET STRING	read-only	Remote E.164/X.125 address for the circuit.
I32 cfrSvcCommitBurstIn	1.3.6.1.4.1.9.9.49.1.4.1.1.6	Integer32	read-only	Circuit's incoming Committed Burst Rate. See ANSI and/or ITU specifications for definition and calculations. For outgoing CBR, see frCircuitCommittedBurst per RFC 1315.
cfrSvcEntry	1.3.6.1.4.1.9.9.49.1.4.1.1		not-accessible	Each entry of the table contains circuit information specific to a Frame Relay Switched Virtual Circuit.
I32 cfrSvcExcessBurstIn	1.3.6.1.4.1.9.9.49.1.4.1.1.7	Integer32	read-only	Circuit's incoming Excess Burst Rate. See ANSI and/or ITU specifications for definition and calculations. For outgoing EBR, see frCircuitExcessBurst per RFC 1315.
I32 cfrSvcIdleTime	1.3.6.1.4.1.9.9.49.1.4.1.1.8	Integer32	read-only	Circuit's idle time period. If expires, the circuit is cleared.
I32 cfrSvcMinThruputIn	1.3.6.1.4.1.9.9.49.1.4.1.1.5	Integer32	read-only	Circuit's incoming minimal Throughput.
I32 cfrSvcMinThruputOut	1.3.6.1.4.1.9.9.49.1.4.1.1.4	Integer32	read-only	Circuit's outgoing minimal Throughput.
cfrSvcObjs	1.3.6.1.4.1.9.9.49.1.4
cfrSvcTable	1.3.6.1.4.1.9.9.49.1.4.1		not-accessible	Table of FR SVC specific, descriptive and statistics information.
I32 cfrSvcThroughputIn	1.3.6.1.4.1.9.9.49.1.4.1.1.3	Integer32	read-only	Circuit's incoming throughput. For outgoing throughput (commonly referred to as CIR) see frCircuitThroughput per RFC1315.
ciscoExtCircuitMIBGroup	1.3.6.1.4.1.9.9.49.3.2.5			A collection of objects that provide Cisco implementation specific FR circuit information. This is a Cisco extension for the frCircuitTable of RFC 1315.
ciscoExtCircuitMIBGroup1	1.3.6.1.4.1.9.9.49.3.2.13			A collection of objects that provide Cisco implementation specific FR circuit information. This is a Cisco extension for the frCircuitTable of RFC 1315.
ciscoFrameRelayMIB	1.3.6.1.4.1.9.9.49			Cisco Frame Relay MIB
ciscoFrCircuitMIBGroup	1.3.6.1.4.1.9.9.49.3.2.4			A collection of objects providing information of a circuit that are not included in frCircuitTable of RFC1315 but are generic to Frame Relay.
ciscoFrConnMIBGroup	1.3.6.1.4.1.9.9.49.3.2.12			A collection of objects providing router's fragmentation information.
ciscoFrElmiMIBGroup	1.3.6.1.4.1.9.9.49.3.2.9			A collection of objects providing router's ELMI information.
ciscoFrElmiMIBGroup1	1.3.6.1.4.1.9.9.49.3.2.10			A collection of objects providing router's ELMI information.
ciscoFrFragMIBGroup	1.3.6.1.4.1.9.9.49.3.2.11			A collection of objects providing router's fragmentation information.
ciscoFrLmiMIBGroup	1.3.6.1.4.1.9.9.49.3.2.3			A collection of objects providing router's Frame Relay LMI configuration and statistics information either supplemental to the frDlcmiTable of RFC 1315 or specific to Cisco's implementation.
ciscoFrMapMIBGroup	1.3.6.1.4.1.9.9.49.3.2.7			A collection of objects to provide mapping information of a Frame Relay virtual circuit. These are additional to the IETF standard Frame Relay DTE MIB.
ciscoFrMIBCompliance	1.3.6.1.4.1.9.9.49.3.1.1			The compliance statement for entities which implement this Cisco Frame Relay MIB.
ciscoFrMIBCompliances	1.3.6.1.4.1.9.9.49.3.1
ciscoFrMIBCompliancesRev1	1.3.6.1.4.1.9.9.49.3.1.2			The compliance statement for entities which implement this Cisco Frame Relay MIB.
ciscoFrMIBCompliancesRev2	1.3.6.1.4.1.9.9.49.3.1.3			The compliance statement for entities which implement this Cisco Frame Relay MIB.
ciscoFrMIBCompliancesRev3	1.3.6.1.4.1.9.9.49.3.1.4			The compliance statement for entities which implement this Cisco Frame Relay MIB.
ciscoFrMIBCompliancesRev4	1.3.6.1.4.1.9.9.49.3.1.5			The compliance statement for entities which implement this Cisco Frame Relay MIB.
ciscoFrMIBConformance	1.3.6.1.4.1.9.9.49.3
ciscoFrMIBGroup	1.3.6.1.4.1.9.9.49.3.2.1			The compliance statement for entities which implement this Cisco Frame Relay MIB.
ciscoFrMIBGroupRev1	1.3.6.1.4.1.9.9.49.3.2.2			A collection of objects providing router's Frame Relay configuration and statistics information that are additional to the IETF standard Frame Relay DTE MIB.
ciscoFrMIBGroups	1.3.6.1.4.1.9.9.49.3.2
ciscoFrMIBObjects	1.3.6.1.4.1.9.9.49.1
ciscoFrSvcMIBGroup	1.3.6.1.4.1.9.9.49.3.2.8			A collection of objects to provide circuit information specific to a Frame Relay Switched Virtual Circuit.This is in addition to the IETF standard Frame Relay DTE MIB.
ciscoFrTsMIBGroup	1.3.6.1.4.1.9.9.49.3.2.6			A collection of objects that provide information about Frame Relay Traffic Shaping. These are additional to the IETF standard Frame Relay DTE MIB.

RFC description

Manages Frame Relay PVC configuration, traffic statistics, and QoS parameters on Cisco WAN interfaces.

Start monitoring Cisco routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-FRAME-RELAY-MIB