All MIBs › Juniper-L2TP-MIB
Organization: Juniper Networks, Inc.
Last Updated: 2006-04-20
Category: Protocol: L2TP, Vendor: Juniper
Description: Provides managed objects for L2TP tunnel status, session counts, and statistics on Juniper Networks E-series broadband access routers.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is Juniper-L2TP-MIB?
Juniper-L2TP-MIB is a Juniper Networks enterprise MIB that manages Layer 2 Tunneling Protocol (L2TP) functionality on Juniper's E-series broadband services routers, used for terminating subscriber PPP-over-L2TP tunnels in broadband access networks. It exposes system-wide L2TP configuration objects controlling tunnel behavior, such as timeouts, retransmission counts, and load-balancing/failover policy, alongside a notifications group for L2TP-related trap events. Its primary monitoring value is software/protocol-state oriented: juniL2tpSysConfigAdminState reflects whether L2TP processing is administratively enabled, and juniL2tpTraps deliver operational events (such as tunnel failures) that indicate service-affecting problems rather than physical hardware faults. It depends on the general L2TP protocol standard (RFC 2661) for the underlying tunneling semantics it configures and monitors. It is typically deployed by broadband/ISP operators running Juniper E-series edge routers that terminate large numbers of subscriber L2TP tunnels, where Juniper-L2TP-MIB SNMP monitoring tracks tunnel state at scale.
IPNetwork Monitor allows you to monitor SNMP objects defined in Juniper-L2TP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Juniper Networks E-series broadband services routers
Monitoring Examples
An operator would poll juniL2tpSysConfigAdminState to confirm L2TP service is enabled, and check juniL2tpSysConfigTunnelIdleTimeout and juniL2tpSysConfigControlRetransmissions to verify tunnel-resilience settings are as expected during a troubleshooting session. Subscribing to juniL2tpTrapControl-governed notifications under juniL2tpTraps would alert the NOC to tunnel-switching events or failover activity, for example when juniL2tpSysConfigFailoverWithinPreference-driven failover kicks in unexpectedly, indicating a peer LNS/LAC reachability problem.
What Can Be Monitored
- L2TP administrative state
- tunnel idle timeout
- control message retransmission counts
- tunnel failover/load-balancing events
- tunnel switching status
This MIB depends on
Related MIBs
Imported Objects
From IF-MIB
| InterfaceIndex | |
| InterfaceIndexOrZero |
From Juniper-MIBs
| juniMibs | MODULE-IDENTITY |
From Juniper-TC
| JuniEnable |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TimeStamp | |
| TruthValue |
How to Use in IPNetwork Monitor
Example using juniL2tpSysStatusTotalDestinations OID:
Select a Juniper Networks E-series broadband services router (L2TP tunnel termination) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type juniL2tpSysStatusTotalDestinations into the Find box to locate it in the OID tree, then select it and click OK. It reports the number of destination creations attempted. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| juniL2tpMIB | 1.3.6.1.4.1.4874.2.2.35 | The L2TP MIB for the Juniper Networks enterprise. | ||
| juniL2tpTraps | 1.3.6.1.4.1.4874.2.2.35.0 | |||
| juniL2tpObjects | 1.3.6.1.4.1.4874.2.2.35.1 | |||
| juniL2tpSystem | 1.3.6.1.4.1.4874.2.2.35.1.1 | |||
| juniL2tpSystemConfig | 1.3.6.1.4.1.4874.2.2.35.1.1.1 | |||
| JUN juniL2tpSysConfigAdminState | 1.3.6.1.4.1.4874.2.2.35.1.1.1.1 | JuniL2tpAdminState | read-write | Exerts control over all L2TP tunnels/sessions in the system. |
| I32 juniL2tpSysConfigDestructTimeout | 1.3.6.1.4.1.4874.2.2.35.1.1.1.2 | Integer32 | read-write | The amount of time, in seconds, to preserve dynamic tunnels/sessions after they become inactive, e.g. to poll their statistics. |
| JUN juniL2tpSysConfigIpChecksumEnable | 1.3.6.1.4.1.4874.2.2.35.1.1.1.3 | JuniEnable | read-write | Enable/disable IP checksumming for tunnels with UDP/IP transport. |
| JUN juniL2tpSysConfigTunnelSwitchingEnabled | 1.3.6.1.4.1.4874.2.2.35.1.1.1.4 | JuniEnable | read-write | Tunnel switching enabled/disable. |
| I32 juniL2tpSysConfigControlRetransmissions | 1.3.6.1.4.1.4874.2.2.35.1.1.1.5 | Integer32 | read-write | The number of retransmission retries allowed before control connection goes down. This object has been replaced by juniL2tpSysConfigControlRetransmissionsEstablished and juniL2tpSysConfigControlRetransmissionsNotEstablished. |
| I32 juniL2tpSysConfigTunnelIdleTimeout | 1.3.6.1.4.1.4874.2.2.35.1.1.1.6 | Integer32 | read-write | Idle tunnel remains active for the specified amount of time; value 0 disables the timer i.e. tunnel becomes persistent. |
| JUN juniL2tpSysConfigReceiveDataSequencingIgnore | 1.3.6.1.4.1.4874.2.2.35.1.1.1.7 | JuniEnable | read-write | Enable/disable ignoring of receive sequencing of L2TP data packets. |
| JUN juniL2tpSysConfigFailoverWithinPreference | 1.3.6.1.4.1.4874.2.2.35.1.1.1.8 | JuniEnable | read-write | Enable/disable fail-over within a preference level. |
| JUN juniL2tpSysConfigWeightedLoadBalancing | 1.3.6.1.4.1.4874.2.2.35.1.1.1.9 | JuniEnable | read-write | Enable/disable weighted load balancing. |
| I32 juniL2tpSysConfigControlRetransmissionsEstablished | 1.3.6.1.4.1.4874.2.2.35.1.1.1.10 | Integer32 | read-write | It represents number of retries allowed for established tunnels before control connection goes down. |
| I32 juniL2tpSysConfigControlRetransmissionsNotEstablished | 1.3.6.1.4.1.4874.2.2.35.1.1.1.11 | Integer32 | read-write | It represents number of retries allowed for unestablished tunnels before control connection goes down. |
| JUN juniL2tpSysConfigDisableChallenge | 1.3.6.1.4.1.4874.2.2.35.1.1.1.12 | JuniEnable | read-write | Disable inclusion of chap challenge in the outgoing packets. |
| JUN juniL2tpSysConfigDisableCallingNumberAvp | 1.3.6.1.4.1.4874.2.2.35.1.1.1.13 | JuniEnable | read-write | Enable/disable inclusion of calling number avp in ICRQ packet. |
| INT juniL2tpSysConfigIgnoreTxAddressChange | 1.3.6.1.4.1.4874.2.2.35.1.1.1.14 | INTEGER | read-write | Configure L2TP to ignore IP address and/or UDP port changes on incoming SCCRP messages. When this feature is enabled the L2TP tunnel may have separate receive and transmit address and/or port values to the remote host. disable(0) - change is not ignored ipAddressAndUdpPort(1)- ignore both address and port changes ipAddress(2) - ignore address changes only udpPort(3) - ignore port changes only. |
| JUN juniL2tpSysConfigEnableDisconnectCauseAvp | 1.3.6.1.4.1.4874.2.2.35.1.1.1.15 | JuniEnable | read-write | Enable/disable inclusion of L2TP PPP Disconnect Cause AVP in CDN packet. |
| I32 juniL2tpSysConfigReceiveWindowSize | 1.3.6.1.4.1.4874.2.2.35.1.1.1.16 | Integer32 | read-write | Configure the global L2TP receive window size. A value of 0 indicates the system chooses the RWS. This object may be overwritten by other more specific RWS settings. |
| JUN juniL2tpSysConfigEnableRxSpeedAvpWhenEqual | 1.3.6.1.4.1.4874.2.2.35.1.1.1.17 | JuniEnable | read-write | Enable/disable generation of L2TP RX speed AVP when RX and TX speeds are equal. Note the RX speed is always generated when the RX and TX speeds differ. |
| INT juniL2tpSysConfigRejectTxAddressChange | 1.3.6.1.4.1.4874.2.2.35.1.1.1.18 | INTEGER | read-write | Configure L2TP to reject IP address and/or UDP port changes on incomming SCCRP messages. disable(0) - address change is allowed ipAddressAndUdpPort(1)- reject both address and port changes ipAddress(2) - reject address changes only udpPort(3) - reject port changes only. |
| INT juniL2tpSysConfigShortDrainTimeout | 1.3.6.1.4.1.4874.2.2.35.1.1.1.19 | INTEGER | read-write | Configure the L2TP short drain interval. This interval represents the time a tunnel, that is already draining, will continue to drain upon receiving a start request. |
| JUN juniL2tpSysConfigDestinationLockoutTestEnabled | 1.3.6.1.4.1.4874.2.2.35.1.1.1.20 | JuniEnable | read-write | Enable/disable testing of failed destiantion before removing lockout. |
| I32 juniL2tpSysConfigDestinationLockoutTimeout | 1.3.6.1.4.1.4874.2.2.35.1.1.1.21 | Integer32 | read-write | Failed destination remains locked out for the specified amount of time. |
| INT juniL2tpSysConfigFailoverResync | 1.3.6.1.4.1.4874.2.2.35.1.1.1.22 | INTEGER | read-write | Configure L2TP failover resync mechanism. disable(0) - Disable failover resync failoverProtocol(1) - Use the L2TP Failover Protocol silentFailover(2) - Use the JUNOSe Silent Failover Mechanism failoverProtocolFallbackToSilentFailover(3) - (Default) Use the L2TP Failover Protocol and fall back to Silent Failover. |
| juniL2tpSystemStatus | 1.3.6.1.4.1.4874.2.2.35.1.1.2 | |||
| OCT juniL2tpSysStatusProtocolVersion | 1.3.6.1.4.1.4874.2.2.35.1.1.2.1 | OCTET STRING | read-only | Vector of supported L2TP protocol version and revision numbers. Supported versions are identified via a two octet pairing where the first octet indicates the version and the second octet contains the revision. |
| STR juniL2tpSysStatusVendorName | 1.3.6.1.4.1.4874.2.2.35.1.1.2.2 | DisplayString | read-only | Vendor name of the L2TP protocol stack. |
| I32 juniL2tpSysStatusFirmwareRev | 1.3.6.1.4.1.4874.2.2.35.1.1.2.3 | Integer32 | read-only | Firmware revision for the L2TP protocol stack. |
| C32 juniL2tpSysStatusTotalDestinationsEx | 1.3.6.1.4.1.4874.2.2.35.1.1.2.4 | Counter32 | read-only | Number of destination creations attempted. |
| C32 juniL2tpSysStatusFailedDestinations | 1.3.6.1.4.1.4874.2.2.35.1.1.2.5 | Counter32 | read-only | Number of destination creation attempts that failed. |
| G32 juniL2tpSysStatusActiveDestinations | 1.3.6.1.4.1.4874.2.2.35.1.1.2.6 | Gauge32 | read-only | Number of destinations having at least one active tunnel. |
| C32 juniL2tpSysStatusTotalTunnels | 1.3.6.1.4.1.4874.2.2.35.1.1.2.7 | Counter32 | read-only | Number of tunnel creations attempted. |
| C32 juniL2tpSysStatusFailedTunnels | 1.3.6.1.4.1.4874.2.2.35.1.1.2.8 | Counter32 | read-only | Number of tunnel creation attempts that failed to reach the established state. |
| C32 juniL2tpSysStatusFailedTunnelAuthens | 1.3.6.1.4.1.4874.2.2.35.1.1.2.9 | Counter32 | read-only | Number of tunnel creation attempts that failed authentication. |
| G32 juniL2tpSysStatusActiveTunnels | 1.3.6.1.4.1.4874.2.2.35.1.1.2.10 | Gauge32 | read-only | Number of tunnels currently established. |
| C32 juniL2tpSysStatusTotalSessions | 1.3.6.1.4.1.4874.2.2.35.1.1.2.11 | Counter32 | read-only | Number of session creations attempted. |
| C32 juniL2tpSysStatusFailedSessions | 1.3.6.1.4.1.4874.2.2.35.1.1.2.12 | Counter32 | read-only | Number of session creation attempts that failed to reach the established state. |
| G32 juniL2tpSysStatusActiveSessions | 1.3.6.1.4.1.4874.2.2.35.1.1.2.13 | Gauge32 | read-only | Number of sessions currently established. |
| C32 juniL2tpSysStatusTotalSwitchedSessions | 1.3.6.1.4.1.4874.2.2.35.1.1.2.14 | Counter32 | read-only | Number of switched session creations attempted. |
| C32 juniL2tpSysStatusFailedSwitchedSessions | 1.3.6.1.4.1.4874.2.2.35.1.1.2.15 | Counter32 | read-only | Number of switched session creation attempts that failed to reach the established state. |
| G32 juniL2tpSysStatusActiveSwitchedSessions | 1.3.6.1.4.1.4874.2.2.35.1.1.2.16 | Gauge32 | read-only | Number of switched sessions currently established. |
| TIM juniL2tpSysStatusIfCounterDiscontinuityTime | 1.3.6.1.4.1.4874.2.2.35.1.1.2.17 | TimeStamp | read-only | The value of sysUpTime on the most recent occasion at which any one or more of the system-level status and statistics suffered a discontinuity. If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value. |
| juniL2tpDestination | 1.3.6.1.4.1.4874.2.2.35.1.2 | |||
| juniL2tpDestConfig | 1.3.6.1.4.1.4874.2.2.35.1.2.1 | |||
| juniL2tpDestConfigTable | 1.3.6.1.4.1.4874.2.2.35.1.2.1.2 | not-accessible | The L2TP destination configuration table. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in juniL2tpDestStatsTable. | |
| juniL2tpDestConfigEntry | 1.3.6.1.4.1.4874.2.2.35.1.2.1.2.1 | not-accessible | Describes the configuration attributes of an L2TP destination. | |
| NUM juniL2tpDestConfigIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.2.1.2.1.1 | InterfaceIndex | not-accessible | Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| ROW juniL2tpDestConfigRowStatus | 1.3.6.1.4.1.4874.2.2.35.1.2.1.2.1.2 | RowStatus | read-create | An implementation may choose not to support administrative configuration of tunnels. |
| JUN juniL2tpDestConfigAdminState | 1.3.6.1.4.1.4874.2.2.35.1.2.1.2.1.3 | JuniL2tpAdminState | read-create | The configured administrative state. |
| JUN juniL2tpDestConfigLockoutAction | 1.3.6.1.4.1.4874.2.2.35.1.2.1.2.1.4 | JuniL2tpLockoutAction | read-create | The lockout action to be applied to a destination. |
| juniL2tpDestStatus | 1.3.6.1.4.1.4874.2.2.35.1.2.2 | |||
| juniL2tpDestStatusTable | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1 | not-accessible | The L2TP destination status table. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in juniL2tpDestConfigTable. | |
| juniL2tpDestStatusEntry | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1 | not-accessible | Describes the status attributes of an L2TP destination. | |
| NUM juniL2tpDestStatusIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.1 | InterfaceIndex | not-accessible | Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| JUN juniL2tpDestStatusTransport | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.2 | JuniL2tpTransport | read-only | The underlying transport over which this L2TP destination is carried. |
| JUN juniL2tpDestStatusEffectiveAdminState | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.3 | JuniL2tpAdminState | read-only | The administrative state currently in effect. This could be the configured admin state for this destination, or an overriding admin state exerted from a higher hierarchical level (system). |
| C32 juniL2tpDestStatusTotalTunnels | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.4 | Counter32 | read-only | Number of tunnel creations attempted. |
| C32 juniL2tpDestStatusFailedTunnels | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.5 | Counter32 | read-only | Number of tunnel creation attempts that failed to reach the established state. |
| C32 juniL2tpDestStatusFailedTunnelAuthens | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.6 | Counter32 | read-only | Number of tunnel creation attempts that failed authentication. |
| G32 juniL2tpDestStatusActiveTunnels | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.7 | Gauge32 | read-only | Number of tunnels currently established. |
| C32 juniL2tpDestStatusTotalSessions | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.8 | Counter32 | read-only | Number of session creations attempted. |
| C32 juniL2tpDestStatusFailedSessions | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.9 | Counter32 | read-only | Number of session creation attempts that failed to reach the established state. |
| G32 juniL2tpDestStatusActiveSessions | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.10 | Gauge32 | read-only | Number of sessions currently established. |
| JUN juniL2tpDestStatusLockoutState | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.11 | JuniL2tpLockoutState | read-only | Lockout state of destination. |
| G32 juniL2tpDestStatusLockoutTimeRemaining | 1.3.6.1.4.1.4874.2.2.35.1.2.2.1.1.12 | Gauge32 | read-only | Lockout timeout remaining. |
| juniL2tpDestStatistics | 1.3.6.1.4.1.4874.2.2.35.1.2.3 | |||
| juniL2tpDestStatTable | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1 | not-accessible | The L2TP destination statistics table. Describes the aggregate control and payload statistics for all L2TP tunnels configured on each destination. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in juniL2tpDestConfigTable. | |
| juniL2tpDestStatEntry | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1 | not-accessible | Describes the aggregate L2TP control and payload statistics for all L2TP tunnels on an L2TP destination. | |
| NUM juniL2tpDestStatIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.1 | InterfaceIndex | not-accessible | Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| C32 juniL2tpDestStatCtlRecvOctets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.2 | Counter32 | read-only | Number of control octets received. |
| C32 juniL2tpDestStatCtlRecvPackets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.3 | Counter32 | read-only | Number of control packets received. |
| C32 juniL2tpDestStatCtlRecvErrors | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.4 | Counter32 | read-only | Number of control packets incurring reception errors. |
| C32 juniL2tpDestStatCtlRecvDiscards | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.5 | Counter32 | read-only | Number of control packets discarded after reception. |
| C32 juniL2tpDestStatCtlSendOctets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.6 | Counter32 | read-only | Number of control octets sent. |
| C32 juniL2tpDestStatCtlSendPackets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.7 | Counter32 | read-only | Number of control packets sent. |
| C32 juniL2tpDestStatCtlSendErrors | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.8 | Counter32 | read-only | Number of control packets incurring transmission errors. |
| C32 juniL2tpDestStatCtlSendDiscards | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.9 | Counter32 | read-only | Number of control packets discarded before transmission. |
| C32 juniL2tpDestStatPayRecvOctets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.10 | Counter32 | read-only | Number of payload octets received. |
| C32 juniL2tpDestStatPayRecvPackets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.11 | Counter32 | read-only | Number of payload packets received. |
| C32 juniL2tpDestStatPayRecvErrors | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.12 | Counter32 | read-only | Number of payload packets incurring reception errors. |
| C32 juniL2tpDestStatPayRecvDiscards | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.13 | Counter32 | read-only | Number of payload packets discarded after reception. |
| C32 juniL2tpDestStatPaySendOctets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.14 | Counter32 | read-only | Number of payload octets sent. |
| C32 juniL2tpDestStatPaySendPackets | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.15 | Counter32 | read-only | Number of payload packets sent. |
| C32 juniL2tpDestStatPaySendErrors | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.16 | Counter32 | read-only | Number of payload packets incurring transmission errors. |
| C32 juniL2tpDestStatPaySendDiscards | 1.3.6.1.4.1.4874.2.2.35.1.2.3.1.1.17 | Counter32 | read-only | Number of payload packets discarded before transmission. |
| juniL2tpTunnel | 1.3.6.1.4.1.4874.2.2.35.1.3 | |||
| juniL2tpTunnelConfig | 1.3.6.1.4.1.4874.2.2.35.1.3.1 | |||
| juniL2tpTunnelConfigTable | 1.3.6.1.4.1.4874.2.2.35.1.3.1.2 | not-accessible | The L2TP tunnel configuration table. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in juniL2tpTunnelStatsTable. | |
| juniL2tpTunnelConfigEntry | 1.3.6.1.4.1.4874.2.2.35.1.3.1.2.1 | not-accessible | Describes the configuration attributes of an L2TP tunnel. | |
| NUM juniL2tpTunnelConfigIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.3.1.2.1.1 | InterfaceIndex | not-accessible | Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| ROW juniL2tpTunnelConfigRowStatus | 1.3.6.1.4.1.4874.2.2.35.1.3.1.2.1.2 | RowStatus | read-create | An implementation may choose not to support administrative configuration of tunnels. |
| JUN juniL2tpTunnelConfigAdminState | 1.3.6.1.4.1.4874.2.2.35.1.3.1.2.1.3 | JuniL2tpAdminState | read-create | The configured administrative state. |
| juniL2tpTunnelStatus | 1.3.6.1.4.1.4874.2.2.35.1.3.2 | |||
| juniL2tpTunnelStatusTable | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1 | not-accessible | The L2TP tunnel status and statistics table. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in juniL2tpTunnelConfigTable. | |
| juniL2tpTunnelStatusEntry | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1 | not-accessible | An L2TP tunnel interface stats entry. | |
| NUM juniL2tpTunnelStatusIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.1 | InterfaceIndex | not-accessible | Same as the value of ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| JUN juniL2tpTunnelStatusTransport | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.2 | JuniL2tpTransport | read-only | The underlying transport over which this L2TP tunnel is carried. |
| JUN juniL2tpTunnelStatusLocalTunnelId | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.3 | JuniL2tpTunnelId | read-only | The local tunnel identifier. |
| JUN juniL2tpTunnelStatusRemoteTunnelId | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.4 | JuniL2tpTunnelId | read-only | The remote tunnel identifier. |
| JUN juniL2tpTunnelStatusEffectiveAdminState | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.5 | JuniL2tpAdminState | read-only | The administrative state currently in effect. This could be the configured admin state for this tunnel, or an overriding admin state exerted from a higher hierarchical level (system, destination). |
| INT juniL2tpTunnelStatusState | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.6 | INTEGER | read-only | The current state of the tunnel. |
| INT juniL2tpTunnelStatusInitiated | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.7 | INTEGER | read-only | Indicates whether the tunnel was initiated locally, or by the remote tunnel peer. |
| STR juniL2tpTunnelStatusRemoteHostName | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.8 | DisplayString | read-only | The host name obtained during the tunnel establishment phase (via the Host Name AVP) of the L2TP peer. If the tunnel is idle, this object should maintain its value from the last time it was connected, or a zero-length string if no name was previously known. |
| STR juniL2tpTunnelStatusRemoteVendorName | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.9 | DisplayString | read-only | Identifies the vendor name of the peer's L2TP implementation. If the tunnel is idle, this object should maintain its value from the last time it was connected, of a zero-length string if no name was previously known. |
| I32 juniL2tpTunnelStatusRemoteFirmwareRevision | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.10 | Integer32 | read-only | The tunnel peer's firmware revision number. If the tunnel is idle, this object should maintain its value from the last time it was connected, or a zero value if no revision was previously known. |
| OCT juniL2tpTunnelStatusRemoteProtocolVersion | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.11 | OCTET STRING | read-only | The protocol version and revision of the tunnel peer's implementation. The first octet contains the protocol version. The second octet contains the protocol revision. |
| INT juniL2tpTunnelStatusRemoteBearerCapabilities | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.12 | INTEGER | read-only | The Bearer Capabilities of the tunnel peer. If the tunnel is idle this object should maintain its value from the last time it was connected, or 'none' if not previously known. |
| INT juniL2tpTunnelStatusRemoteFramingCapabilities | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.13 | INTEGER | read-only | The Framing Capabilities of the tunnel peer. If the tunnel is idle this object should maintain its value from the last time it was connected, or 'none' if not previously known. |
| G32 juniL2tpTunnelStatusRecvWindowSize | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.14 | Gauge32 | read-only | The receive window size. |
| G32 juniL2tpTunnelStatusSendWindowSize | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.15 | Gauge32 | read-only | The tunnel peer's receive window size. |
| G32 juniL2tpTunnelStatusSendQueueDepth | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.16 | Gauge32 | read-only | Number of control packets on transmit queue. |
| I32 juniL2tpTunnelStatusRecvSeq | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.17 | Integer32 | read-only | The next sequence number expected in a received control packet. |
| I32 juniL2tpTunnelStatusRecvSeqAck | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.18 | Integer32 | read-only | The last received sequence number that was acknowledged back to the tunnel peer. |
| I32 juniL2tpTunnelStatusSendSeq | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.19 | Integer32 | read-only | The next sequence number to be sent in a transmitted control packet. |
| I32 juniL2tpTunnelStatusSendSeqAck | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.20 | Integer32 | read-only | The send sequence number that the tunnel peer has acknowledged. The flow control state can be determined by subtracting the juniL2tpTunnelStatusSendSeq from juniL2tpTunnelStatusSendSeqAck and comparing this value to juniL2tpTunnelStatusSendWindowSize. |
| C32 juniL2tpTunnelStatusTotalSessions | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.21 | Counter32 | read-only | The total number of sessions that this tunnel has successfully connected through to its tunnel peer since this tunnel was created, including those that have since terminated. |
| C32 juniL2tpTunnelStatusFailedSessions | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.22 | Counter32 | read-only | The number of sessions that were initiated but failed to reach the established phase. |
| G32 juniL2tpTunnelStatusActiveSessions | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.23 | Gauge32 | read-only | The current number of sessions in the established state. |
| I32 juniL2tpTunnelStatusLastResultCode | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.24 | Integer32 | read-only | The last value of the result code as described in the Result Code AVP which caused the tunnel to disconnect. |
| I32 juniL2tpTunnelStatusLastErrorCode | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.25 | Integer32 | read-only | The last value of the error code as described in the Result Code AVP which caused the tunnel to disconnect. |
| STR juniL2tpTunnelStatusLastErrorMessage | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.26 | DisplayString | read-only | The last value of the optional message as described in the Result Code AVP which caused the tunnel to disconnect. |
| U32 juniL2tpTunnelStatusCumEstabTime | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.27 | Unsigned32 | read-only | The cumulative time in seconds that this tunnel, since first being created, has spent in the established state (which may be punctuated by intervals outside the established state). |
| I32 juniL2tpTunnelStatusEffectiveFailoverResync | 1.3.6.1.4.1.4874.2.2.35.1.3.2.1.1.28 | Integer32 | read-only | The mechanism employed following failover to resynchronize with the L2TP peer. |
| juniL2tpTunnelStatistics | 1.3.6.1.4.1.4874.2.2.35.1.3.3 | |||
| juniL2tpTunnelStatTable | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1 | not-accessible | The L2TP tunnel statistics table. Describes the control and payload statistics for each L2TP tunnel. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in juniL2tpTunnelConfigTable. | |
| juniL2tpTunnelStatEntry | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1 | not-accessible | Describes the L2TP control and payload statistics for an L2TP tunnel. | |
| NUM juniL2tpTunnelStatIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.1 | InterfaceIndex | not-accessible | Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| C32 juniL2tpTunnelStatCtlRecvOctets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.2 | Counter32 | read-only | Number of control octets received. |
| C32 juniL2tpTunnelStatCtlRecvPackets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.3 | Counter32 | read-only | Number of control packets received. |
| C32 juniL2tpTunnelStatCtlRecvErrors | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.4 | Counter32 | read-only | Number of control packets incurring reception errors. |
| C32 juniL2tpTunnelStatCtlRecvDiscards | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.5 | Counter32 | read-only | Number of control packets discarded after reception. |
| C32 juniL2tpTunnelStatCtlSendOctets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.6 | Counter32 | read-only | Number of control octets sent. |
| C32 juniL2tpTunnelStatCtlSendPackets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.7 | Counter32 | read-only | Number of control packets sent. |
| C32 juniL2tpTunnelStatCtlSendErrors | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.8 | Counter32 | read-only | Number of control packets incurring transmission errors. |
| C32 juniL2tpTunnelStatCtlSendDiscards | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.9 | Counter32 | read-only | Number of control packets discarded before transmission. |
| C32 juniL2tpTunnelStatPayRecvOctets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.10 | Counter32 | read-only | Number of payload octets received. |
| C32 juniL2tpTunnelStatPayRecvPackets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.11 | Counter32 | read-only | Number of payload packets received. |
| C32 juniL2tpTunnelStatPayRecvErrors | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.12 | Counter32 | read-only | Number of payload packets incurring reception errors. |
| C32 juniL2tpTunnelStatPayRecvDiscards | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.13 | Counter32 | read-only | Number of payload packets discarded after reception. |
| C32 juniL2tpTunnelStatPaySendOctets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.14 | Counter32 | read-only | Number of payload octets sent. |
| C32 juniL2tpTunnelStatPaySendPackets | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.15 | Counter32 | read-only | Number of payload packets sent. |
| C32 juniL2tpTunnelStatPaySendErrors | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.16 | Counter32 | read-only | Number of payload packets incurring transmission errors. |
| C32 juniL2tpTunnelStatPaySendDiscards | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.17 | Counter32 | read-only | Number of payload packets discarded before transmission. |
| C32 juniL2tpTunnelStatCtlRecvZLB | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.18 | Counter32 | read-only | Number of Zero Length Body control packet acknowledgement packets that were received. |
| C32 juniL2tpTunnelStatCtlRecvOutOfSequence | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.19 | Counter32 | read-only | Number of control packets not received in the correct sequence number order. |
| C32 juniL2tpTunnelStatCtlRecvOutOfWindow | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.20 | Counter32 | read-only | Number of control packets received outside the offered receive window. |
| C32 juniL2tpTunnelStatCtlSendZLB | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.21 | Counter32 | read-only | Number of Zero Length Body control packets sent. |
| C32 juniL2tpTunnelStatCtlSendRetransmits | 1.3.6.1.4.1.4874.2.2.35.1.3.3.1.1.22 | Counter32 | read-only | Number of control packet send retransmissions. |
| juniL2tpTunnelMap | 1.3.6.1.4.1.4874.2.2.35.1.3.4 | |||
| juniL2tpMapTifSidToSifTable | 1.3.6.1.4.1.4874.2.2.35.1.3.4.1 | not-accessible | Table of TunnelIf/SessionId -> SessionIf mappings. | |
| juniL2tpMapTifSidToSifEntry | 1.3.6.1.4.1.4874.2.2.35.1.3.4.1.1 | not-accessible | A mapping of TunnelIf/SessionId to SessionIf. | |
| NUM juniL2tpMapTifSidToSifTunnelIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.3.4.1.1.1 | InterfaceIndex | not-accessible | The ifIndex of a tunnel interface. |
| JUN juniL2tpMapTifSidToSifLocalSessionId | 1.3.6.1.4.1.4874.2.2.35.1.3.4.1.1.2 | JuniL2tpSessionId | not-accessible | A local session ID on the associated tunnel interface. |
| NUM juniL2tpMapTifSidToSifSessionIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.3.4.1.1.3 | InterfaceIndex | read-only | The ifIndex of the session interface identified by this entry's Tunnel ifIndex and local Session ID pair. |
| juniL2tpMapTidToTifTable | 1.3.6.1.4.1.4874.2.2.35.1.3.4.2 | not-accessible | Map L2TP tunnel IDs to tunnel interfaces. | |
| juniL2tpMapTidToTifEntry | 1.3.6.1.4.1.4874.2.2.35.1.3.4.2.1 | not-accessible | A mapping of L2TP tunnel ID to tunnel interface. | |
| JUN juniL2tpMapTidToTifLocalTunnelId | 1.3.6.1.4.1.4874.2.2.35.1.3.4.2.1.1 | JuniL2tpTunnelId | not-accessible | A local tunnel identifier. |
| NUM juniL2tpMapTidToTifIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.3.4.2.1.2 | InterfaceIndex | read-only | The ifIndex of the tunnel interface having the associated tunnel identifier. |
| juniL2tpSession | 1.3.6.1.4.1.4874.2.2.35.1.4 | |||
| juniL2tpSessionConfig | 1.3.6.1.4.1.4874.2.2.35.1.4.1 | |||
| juniL2tpSessionConfigTable | 1.3.6.1.4.1.4874.2.2.35.1.4.1.2 | not-accessible | The L2TP session configuration table. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in juniL2tpSessionStatsTable. | |
| juniL2tpSessionConfigEntry | 1.3.6.1.4.1.4874.2.2.35.1.4.1.2.1 | not-accessible | Describes the configuration attributes of an L2TP session. | |
| NUM juniL2tpSessionConfigIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.4.1.2.1.1 | InterfaceIndex | not-accessible | Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| ROW juniL2tpSessionConfigRowStatus | 1.3.6.1.4.1.4874.2.2.35.1.4.1.2.1.2 | RowStatus | read-create | An implementation may choose not to support administrative configuration of tunnels. |
| JUN juniL2tpSessionConfigAdminState | 1.3.6.1.4.1.4874.2.2.35.1.4.1.2.1.3 | JuniL2tpAdminState | read-create | The configured administrative state. |
| juniL2tpSessionStatus | 1.3.6.1.4.1.4874.2.2.35.1.4.2 | |||
| juniL2tpSessionStatusTable | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1 | not-accessible | The L2TP session status and statistics table. | |
| juniL2tpSessionStatusEntry | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1 | not-accessible | An L2TP session interface status and statistics entry. | |
| NUM juniL2tpSessionStatusIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.1 | InterfaceIndex | not-accessible | The ifIndex of an L2TP session interface. |
| NUM juniL2tpSessionStatusLacPppIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.2 | InterfaceIndexOrZero | read-only | For pass-through PPP sessions (conventional LAC), the ifIndex of an associated local PPP interface through which the remote LAC client was connected. If unknown, this object contains a value of zero. For locally originated PPP sessions (LNS-like), this object has a value of zero. This object is deprecated in favor of juniL2tpSessionStatusLacTunneledIfIndex. |
| JUN juniL2tpSessionStatusLocalSessionId | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.3 | JuniL2tpSessionId | read-only | The local session ID for the session. |
| JUN juniL2tpSessionStatusRemoteSessionId | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.4 | JuniL2tpSessionId | read-only | The remote session ID for the session. |
| STR juniL2tpSessionStatusUserName | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.5 | DisplayString | read-only | The peer session name on this interface, typically the login name of the remote user. If the user name is unknown this object will contain a zero-length string. |
| JUN juniL2tpSessionStatusEffectiveAdminState | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.6 | JuniL2tpAdminState | read-only | The administrative state currently in effect. This could be the configured admin state for this session, or an overriding admin state exerted from a higher hierarchical level (system, destination, tunnel). |
| INT juniL2tpSessionStatusState | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.7 | INTEGER | read-only | The current state of the session. |
| INT juniL2tpSessionStatusCallType | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.8 | INTEGER | read-only | The type of call and role this tunnel peer is providing for this session. For example, lacIncoming(1) indicates this tunnel peer is acting as a LAC and generated a Incoming-Call-Request to the tunnel peer (the LNS). Note that tunnel peers can be both LAC and LNS simultaneously. |
| I32 juniL2tpSessionStatusCallSerialNumber | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.9 | Integer32 | read-only | The serial number assigned to this session. |
| I32 juniL2tpSessionStatusTxConnectSpeed | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.10 | Integer32 | read-only | The last known transmit baud rate for this session. |
| I32 juniL2tpSessionStatusRxConnectSpeed | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.11 | Integer32 | read-only | The last known receive baud rate for this session. |
| INT juniL2tpSessionStatusCallBearerType | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.12 | INTEGER | read-only | The bearer type of this session. |
| INT juniL2tpSessionStatusFramingType | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.13 | INTEGER | read-only | The framing type of this session. |
| I32 juniL2tpSessionStatusPhysChanId | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.14 | Integer32 | read-only | The physical channel identifier for the session. For pass-through PPP sessions, typically the ifIndex of the access interface lying below the PPP interface identified by juniL2tpSessionStatusLacTunneledIfIndex. |
| STR juniL2tpSessionStatusDnis | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.15 | DisplayString | read-only | The Dialed Number Information String that the LAC obtained from the network for the session. If no DNIS was provided, a zero-length string will be returned. |
| STR juniL2tpSessionStatusClid | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.16 | DisplayString | read-only | The Calling Line ID that the LAC obtained from the network for the session. If no CLID was provided, a zero-length string will be returned. |
| STR juniL2tpSessionStatusSubAddress | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.17 | DisplayString | read-only | The SubAddress that the LAC obtained from the network for the session. If no SubAddress was provided, a zero-length string will be returned. |
| STR juniL2tpSessionStatusPrivateGroupId | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.18 | DisplayString | read-only | The Private Group Identifier used for this tunneled session. If no Private Group Identifier was provided, a zero-length string will be returned. |
| T/F juniL2tpSessionStatusProxyLcp | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.19 | TruthValue | read-only | Indicates whether proxy LCP was provided for this session. |
| INT juniL2tpSessionStatusAuthMethod | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.20 | INTEGER | read-only | The proxy authentication method employed by the LAC for the session. If juniL2tpSessionProxyLcp is false(2) this object reports a value of 'none' and should be ignored. |
| INT juniL2tpSessionStatusSequencingState | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.21 | INTEGER | read-only | Indicates which tunnel peers have requested payload sequencing. |
| I32 juniL2tpSessionStatusSendSeq | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.22 | Integer32 | read-only | The next send sequence number. |
| I32 juniL2tpSessionStatusRecvSeq | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.23 | Integer32 | read-only | The next receive sequence number expected. |
| NUM juniL2tpSessionStatusLacTunneledIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.24 | InterfaceIndexOrZero | read-only | For pass-through remote client sessions (conventional LAC), the ifIndex of an associated local interface through which the remote LAC client was connected. If unknown, this object contains a value of zero. For locally originated sessions (LNS-like), this object has a value of zero. |
| U32 juniL2tpSessionStatusCumEstabTime | 1.3.6.1.4.1.4874.2.2.35.1.4.2.1.1.25 | Unsigned32 | read-only | The cumulative time in seconds that this session, since first being created, has spent in the established state (which may be punctuated by intervals outside the established state). |
| juniL2tpSessionStatistics | 1.3.6.1.4.1.4874.2.2.35.1.4.3 | |||
| juniL2tpSessionStatTable | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1 | not-accessible | The L2TP session statistics table. | |
| juniL2tpSessionStatEntry | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1 | not-accessible | An L2TP session interface statistics entry. | |
| NUM juniL2tpSessionStatIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.1 | InterfaceIndex | not-accessible | The ifIndex of an L2TP session interface. |
| C32 juniL2tpSessionStatPayRecvOctets | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.2 | Counter32 | read-only | Number of payload octets received. |
| C32 juniL2tpSessionStatPayRecvPackets | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.3 | Counter32 | read-only | Number of payload packets received. |
| C32 juniL2tpSessionStatPayRecvErrors | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.4 | Counter32 | read-only | Number of payload packets incurring reception errors. |
| C32 juniL2tpSessionStatPayRecvDiscards | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.5 | Counter32 | read-only | Number of payload packets discarded after reception. |
| C32 juniL2tpSessionStatPaySendOctets | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.6 | Counter32 | read-only | Number of payload octets sent. |
| C32 juniL2tpSessionStatPaySendPackets | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.7 | Counter32 | read-only | Number of payload packets sent. |
| C32 juniL2tpSessionStatPaySendErrors | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.8 | Counter32 | read-only | Number of payload packets incurring transmission errors. |
| C32 juniL2tpSessionStatPaySendDiscards | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.9 | Counter32 | read-only | Number of payload packets discarded before transmission. |
| C32 juniL2tpSessionStatRecvOutOfSequence | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.10 | Counter32 | read-only | The number of packets received out of sequence. |
| C32 juniL2tpSessionStatResequencingTimeouts | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.11 | Counter32 | read-only | The number of reassembly timeouts that have occurred. |
| U32 juniL2tpSessionStatPayLostPackets | 1.3.6.1.4.1.4874.2.2.35.1.4.3.1.1.12 | Unsigned32 | read-only | When sequence numbers are enabled, this value represents the estimated number of payload packets lost, based on observed gaps in sequence numbers. This estimate is subject to correction (decrement) upon receipt of out-of-sequence packets that fill previously observed gaps. |
| juniL2tpTransport | 1.3.6.1.4.1.4874.2.2.35.1.5 | |||
| juniL2tpTransportUdpIp | 1.3.6.1.4.1.4874.2.2.35.1.5.1 | |||
| juniL2tpUdpIpSystem | 1.3.6.1.4.1.4874.2.2.35.1.5.1.1 | |||
| juniL2tpUdpIpDestination | 1.3.6.1.4.1.4874.2.2.35.1.5.1.2 | |||
| juniL2tpUdpIpDestTable | 1.3.6.1.4.1.4874.2.2.35.1.5.1.2.1 | not-accessible | The L2TP UDP/IP destination table. Reports the UDP/IP characteristics of a L2TP UDP/IP destination. A L2TP UDP/IP destination is associated with a local router, a local IP address, and with a remote IP address for the L2TP peer. More specific UDP/IP detail per tunnel is reported in the juniL2tpUdpIpTunnelTable. | |
| juniL2tpUdpIpDestEntry | 1.3.6.1.4.1.4874.2.2.35.1.5.1.2.1.1 | not-accessible | Describes the UDP/IP attributes of an L2TP destination. | |
| NUM juniL2tpUdpIpDestIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.5.1.2.1.1.1 | InterfaceIndex | not-accessible | Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| U32 juniL2tpUdpIpDestRouterIndex | 1.3.6.1.4.1.4874.2.2.35.1.5.1.2.1.1.2 | Unsigned32 | read-only | The index of an entry in the juniRouterTable for the local router with which this L2TP destination interface is associated. |
| IP juniL2tpUdpIpDestLocalAddress | 1.3.6.1.4.1.4874.2.2.35.1.5.1.2.1.1.3 | IpAddress | read-only | This L2TP destination's local IP address. |
| IP juniL2tpUdpIpDestRemoteAddress | 1.3.6.1.4.1.4874.2.2.35.1.5.1.2.1.1.4 | IpAddress | read-only | The IP address of the remote L2TP endpoint. |
| juniL2tpUdpIpTunnel | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3 | |||
| juniL2tpUdpIpTunnelTable | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1 | not-accessible | The L2TP UDP/IP tunnel table. Reports the UDP/IP characteristics of L2TP UDP/IP tunnels. A L2TP UDP/IP tunnel is defined in terms of the local and remote IP addresses and UDP ports. | |
| juniL2tpUdpIpTunnelEntry | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1 | not-accessible | An L2TP UDP/IP tunnel entry. | |
| NUM juniL2tpUdpIpTunnelIfIndex | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1.1 | InterfaceIndex | not-accessible | Same as the value of ifIndex for the corresponding entry in Interfaces MIB ifTable. |
| U32 juniL2tpUdpIpTunnelRouterIndex | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1.2 | Unsigned32 | read-only | The index of an entry in the juniRouterTable for the local router with which this L2TP tunnel interface is associated. |
| IP juniL2tpUdpIpTunnelLocalAddress | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1.3 | IpAddress | read-only | The local IP address for this UDP/IP tunnel. |
| I32 juniL2tpUdpIpTunnelLocalPort | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1.4 | Integer32 | read-only | The local UDP port for this UDP/IP tunnel. |
| IP juniL2tpUdpIpTunnelRemoteAddress | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1.5 | IpAddress | read-only | The remote IP address for this UDP/IP tunnel. |
| I32 juniL2tpUdpIpTunnelRemotePort | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1.6 | Integer32 | read-only | The remote UDP port for this UDP/IP tunnel. |
| IP juniL2tpUdpIpTunnelRemoteReceiveAddress | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1.7 | IpAddress | read-only | The remote receive IP address for this UDP/IP tunnel. This object will differ from juniL2tpUdpIpTunnelRemoteAddress when the tunnel uses separate transmit and receive addresses to the remote peer. |
| I32 juniL2tpUdpIpTunnelRemoteReceivePort | 1.3.6.1.4.1.4874.2.2.35.1.5.1.3.1.1.8 | Integer32 | read-only | The remote receive UDP port for this UDP/IP tunnel. This object will differ from juniL2tpUdpIpTunnelRemotePort when the tunnel uses separate transmit and receive ports to the remote peer. |
| juniL2tpUdpIpSession | 1.3.6.1.4.1.4874.2.2.35.1.5.1.4 | |||
| juniL2tpTrapControl | 1.3.6.1.4.1.4874.2.2.35.2 | |||
| juniL2tpConformance | 1.3.6.1.4.1.4874.2.2.35.3 | |||
| juniL2tpGroups | 1.3.6.1.4.1.4874.2.2.35.3.1 | |||
| juniL2tpConfigGroup | 1.3.6.1.4.1.4874.2.2.35.3.1.1 | Obsolete collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. This group became obsolete when juniL2tpSysConfigReceiveDataSequencingIgnore was added. | ||
| juniL2tpStatusGroup | 1.3.6.1.4.1.4874.2.2.35.3.1.2 | Obsolete collection of objects providing status of the L2TP protocol at the system, destination, tunnel, and session levels. This group became obsolete when new objects were added. | ||
| juniL2tpStatGroup | 1.3.6.1.4.1.4874.2.2.35.3.1.3 | Obsolete collection of objects providing statistics of the L2TP protocol at the destination, tunnel, and session levels. This group became obsolete when new objects were added. | ||
| juniL2tpMapGroup | 1.3.6.1.4.1.4874.2.2.35.3.1.4 | A collection of objects providing mapping associations among L2TP components. | ||
| juniL2tpUdpIpGroup | 1.3.6.1.4.1.4874.2.2.35.3.1.5 | Obsolete collection of objects providing UDP/IP transport information for L2TP components. | ||
| juniL2tpStatusGroup2 | 1.3.6.1.4.1.4874.2.2.35.3.1.6 | Obsolete collection of objects providing status of the L2TP protocol at the system, destination, tunnel, and session levels. | ||
| juniL2tpStatGroup2 | 1.3.6.1.4.1.4874.2.2.35.3.1.7 | A collection of objects providing statistics of the L2TP protocol at the destination, tunnel, and session levels. | ||
| juniL2tpConfigGroup2 | 1.3.6.1.4.1.4874.2.2.35.3.1.8 | Obsolete collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. This group became obsolete when new objects were added. | ||
| juniL2tpConfigGroup3 | 1.3.6.1.4.1.4874.2.2.35.3.1.9 | Obsolete collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. This group became obsolete when juniL2tpSysConfigDisableCallingNumberAvp was added. | ||
| juniL2tpConfigGroup4 | 1.3.6.1.4.1.4874.2.2.35.3.1.10 | Obsolete collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. This group became obsolete when new objects were added. | ||
| juniL2tpConfigGroup5 | 1.3.6.1.4.1.4874.2.2.35.3.1.11 | Obsolete collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. This group became obsolete when new objects were added. | ||
| juniL2tpConfigGroup6 | 1.3.6.1.4.1.4874.2.2.35.3.1.12 | Obsolete collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. This group became obsolete when new objects were added. | ||
| juniL2tpConfigGroup7 | 1.3.6.1.4.1.4874.2.2.35.3.1.13 | A collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. | ||
| juniL2tpUdpIpGroup1 | 1.3.6.1.4.1.4874.2.2.35.3.1.14 | A collection of objects providing UDP/IP transport information for L2TP components. | ||
| juniL2tpConfigGroup8 | 1.3.6.1.4.1.4874.2.2.35.3.1.15 | Obsolete collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. | ||
| juniL2tpConfigGroup9 | 1.3.6.1.4.1.4874.2.2.35.3.1.16 | Obsolete collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. | ||
| juniL2tpConfigGroup10 | 1.3.6.1.4.1.4874.2.2.35.3.1.17 | Obsolete collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. | ||
| juniL2tpStatusGroup3 | 1.3.6.1.4.1.4874.2.2.35.3.1.18 | Obsolete collection of objects providing status information of the L2TP protocol, tunnels and sessions. | ||
| juniL2tpConfigGroup11 | 1.3.6.1.4.1.4874.2.2.35.3.1.19 | Obsolete collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. | ||
| juniL2tpConfigGroup12 | 1.3.6.1.4.1.4874.2.2.35.3.1.20 | Obsolete collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. | ||
| juniL2tpStatusGroup4 | 1.3.6.1.4.1.4874.2.2.35.3.1.21 | Obsolete collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. | ||
| juniL2tpConfigGroup13 | 1.3.6.1.4.1.4874.2.2.35.3.1.22 | A collection of objects providing configuration information of the L2TP protocol, tunnels and sessions. | ||
| juniL2tpStatusGroup5 | 1.3.6.1.4.1.4874.2.2.35.3.1.23 | A collection of objects providing status of the L2TP protocol at the system, destination, tunnel, and session levels. | ||
| juniL2tpCompliances | 1.3.6.1.4.1.4874.2.2.35.3.2 | |||
| juniL2tpCompliance | 1.3.6.1.4.1.4874.2.2.35.3.2.1 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when juniL2tpTunnelStatusCumEstabTime, juniL2tpSessionStatusCumEstabTime and juniL2tpSessionStatPayLostPackets were added, and juniL2tpSessionStatusLacTunneledIfIndex replaced juniL2tpSessionStatusLacPppIfIndex. | ||
| juniL2tpCompliance2 | 1.3.6.1.4.1.4874.2.2.35.3.2.2 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when a new object was added to the configuration group. | ||
| juniL2tpCompliance3 | 1.3.6.1.4.1.4874.2.2.35.3.2.3 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when new objects were added to the configuration group. | ||
| juniL2tpCompliance4 | 1.3.6.1.4.1.4874.2.2.35.3.2.4 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when new objects were added to the configuration group. | ||
| juniL2tpCompliance5 | 1.3.6.1.4.1.4874.2.2.35.3.2.5 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when new objects were added to the configuration group. | ||
| juniL2tpCompliance6 | 1.3.6.1.4.1.4874.2.2.35.3.2.6 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when new objects were added to the configuration group. | ||
| juniL2tpCompliance7 | 1.3.6.1.4.1.4874.2.2.35.3.2.7 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when new objects were added to the configuration group. | ||
| juniL2tpCompliance8 | 1.3.6.1.4.1.4874.2.2.35.3.2.8 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when new objects were added to the configuration group. | ||
| juniL2tpCompliance9 | 1.3.6.1.4.1.4874.2.2.35.3.2.9 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when new objects were added to the configuration group. | ||
| juniL2tpCompliance10 | 1.3.6.1.4.1.4874.2.2.35.3.2.10 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when new objects were added to the configuration group. | ||
| juniL2tpCompliance11 | 1.3.6.1.4.1.4874.2.2.35.3.2.11 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when new objects were added to the status group. | ||
| juniL2tpCompliance12 | 1.3.6.1.4.1.4874.2.2.35.3.2.12 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when new objects were added to the config and status groups. | ||
| juniL2tpCompliance13 | 1.3.6.1.4.1.4874.2.2.35.3.2.13 | Obsolete compliance statement for SNMPv2 entities which implement the L2TP MIB. This statement became obsolete when new objects were added to the config and status group. | ||
| juniL2tpCompliance14 | 1.3.6.1.4.1.4874.2.2.35.3.2.14 | The compliance statement for SNMPv2 entities which implement the L2TP MIB. |
RFC description
Juniper Layer 2 Tunneling Protocol MIB for monitoring and managing L2TP tunnels and sessions on Juniper devices. Enables SNMP-based monitoring of L2TP functionality in Juniper Junos OS.
Start monitoring Juniper Networks E-series broadband services router (L2TP tunnel termination) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.