All MIBs › Juniper-L2TP-MIB › juniL2tpSysConfigIgnoreTxAddressChange
juniL2tpSysConfigIgnoreTxAddressChange
Module: Juniper-L2TP-MIB
OID (symbolic): Juniper-L2TP-MIB::juniL2tpSysConfigIgnoreTxAddressChange
OID (numeric): 1.3.6.1.4.1.4874.2.2.35.1.1.1.14
Node type: OBJECT-TYPE
Type: INTEGER
Access: read-write
Description: Configure L2TP to ignore IP address and/or UDP port changes on incoming SCCRP messages. When this feature is enabled the L2TP tunnel may have separate receive and transmit address and/or port values to the remote host. disable(0) - change is not ignored ipAddressAndUdpPort(1)- ignore both address and port changes ipAddress(2) - ignore address changes only udpPort(3) - ignore port changes only.
What is juniL2tpSysConfigIgnoreTxAddressChange?
Read-write control selecting whether the router ignores an incoming SCCRP's transmit IP address and/or UDP port changing from what was originally used: disable(0) treats the change normally, ipAddressAndUdpPort(1) ignores both, ipAddress(2) ignores only the address, and udpPort(3) ignores only the port. Enabling this lets a tunnel keep working even when its peer replies from a different address/port than it received on (e.g. behind certain NAT or load-balanced setups), at the cost of the tunnel's transmit and receive paths becoming asymmetric.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.4874.2.2.35.1.1.1.14 snmpwalk -v2c -c public <target> Juniper-L2TP-MIB::juniL2tpSysConfigIgnoreTxAddressChange
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.4874.2.2.35.1.1.1.14.1 snmpget -v2c -c public <target> Juniper-L2TP-MIB::juniL2tpSysConfigIgnoreTxAddressChange.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.4874.2.2.35.1.1.1.14.1 i <value>
Start monitoring Juniper Networks E-series broadband services router (L2TP tunnel termination) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the Juniper-L2TP-MIB::juniL2tpSysConfigIgnoreTxAddressChange OID value, configure state conditions and alerts, and monitor any Juniper Networks E-series broadband services router (L2TP tunnel termination) from a single console.
OID Breakdown
Upper-level ancestors (9 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.4874 | juniperUni | Juniper-UNI-SMI |
| 1.3.6.1.4.1.4874.2 | juniperUniMibs | Juniper-UNI-SMI |
| 1.3.6.1.4.1.4874.2.2 | juniMibs | Juniper-MIBs |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.4874.2.2.35 | juniL2tpMIB | Juniper-L2TP-MIB |
| 1.3.6.1.4.1.4874.2.2.35.1 | juniL2tpObjects | Juniper-L2TP-MIB |
| 1.3.6.1.4.1.4874.2.2.35.1.1 | juniL2tpSystem | Juniper-L2TP-MIB |
| 1.3.6.1.4.1.4874.2.2.35.1.1.1 | juniL2tpSystemConfig | Juniper-L2TP-MIB |
| 1.3.6.1.4.1.4874.2.2.35.1.1.1.14 | juniL2tpSysConfigIgnoreTxAddressChange | Juniper-L2TP-MIB |