Juniper-BGP-MIB

All MIBs › Juniper-BGP-MIB

Organization: Juniper Networks, Inc.

Last Updated: 2007-05-11

Category: Protocol: BGP, Routing Protocols, Technology: Routing, Vendor: Juniper

Description: Provides managed objects for Border Gateway Protocol (BGP) peer sessions, route statistics, and policy application on Juniper E-series platforms.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Juniper-BGP-MIB?

Juniper-BGP-MIB is a Juniper Networks enterprise MIB providing managed objects for Border Gateway Protocol (BGP) configuration, peer sessions, and route statistics on Juniper E-series routers. It exposes general BGP process configuration (local AS, router identifier, route reflection/confederation settings) as well as route table statistics and connection reset controls. It is used to monitor the software/protocol status of BGP: whether the process is enabled, current route-table scale via the route table statistics group, and abnormal events such as mass session resets triggered through juniBgpResetAllConnectionType. It is conceptually related to, though implemented separately from, the standard BGP4-MIB defined in IETF RFCs. It is deployed on E-series routers participating in service-provider or enterprise BGP routing, where Juniper-BGP-MIB SNMP monitoring gives operators visibility into peer sessions and route-table health.

IPNetwork Monitor allows you to monitor SNMP objects defined in Juniper-BGP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Juniper E-series routers

Monitoring Examples

An admin baselines juniBgpLocalAsNumber and juniBgpIdentifier to confirm router identity within the BGP topology, then watches juniBgpRouteTableStatisticsGroup and juniBgpEqualCostLimit to track route scale and ECMP behavior. Monitoring juniBgpResetAllConnectionType helps detect an operator- or software-triggered mass reset of BGP sessions that would explain a sudden wave of peer flaps.

What Can Be Monitored

BGP session/process state
local AS number and router identifier
route table statistics
equal-cost multipath limit
session reset events
route reflection/confederation configuration

Imported Objects

From Juniper-MIBs

juniMibs

MODULE-IDENTITY

From Juniper-TC

JuniVrfName

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using juniBgpPeerInUpdates OID:

Select a Juniper E-series router (BGP configuration/peer sessions/route stats) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type juniBgpPeerInUpdates into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of BGP UPDATE messages received on this connection. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
juniBgpMIB	1.3.6.1.4.1.4874.2.2.29			The BGP Protocol MIB for the Juniper Networks enterprise.
juniBgpObjects	1.3.6.1.4.1.4874.2.2.29.1
juniBgpGeneralGroup	1.3.6.1.4.1.4874.2.2.29.1.1
I32 juniBgpLocalAsNumber	1.3.6.1.4.1.4874.2.2.29.1.1.1	Integer32	read-write	Deprecated. The local autonomous system number. This object has been replaced by juniBgpFourOctetLocalAsNumber. It is still possible to get and set this object, but if the actual local AS number is greater than 65535, getting this object returns 23456 (AS-TRANS).
T/F juniBgpEnabled	1.3.6.1.4.1.4874.2.2.29.1.1.2	TruthValue	read-write	Set this object to true(1) in order to have BGP router enabled.
IP juniBgpIdentifier	1.3.6.1.4.1.4874.2.2.29.1.1.3	IpAddress	read-write	The BGP identifier of the local system. The identifier is the system router ID by default.
T/F juniBgpAlwaysCompareMed	1.3.6.1.4.1.4874.2.2.29.1.1.4	TruthValue	read-write	Set this object to true(1) in order to compare metrics for paths from neighors of different ASs.
U32 juniBgpDefaultLocalPreference	1.3.6.1.4.1.4874.2.2.29.1.1.5	Unsigned32	read-write	The default local preference.
I32 juniBgpEqualCostLimit	1.3.6.1.4.1.4874.2.2.29.1.1.6	Integer32	read-write	Obsolete maximum equal cost paths to store in the routing table. This object has been replaced by the juniBgpVrfMaximumPathsEbgp object.
T/F juniBgpClientToClientReflection	1.3.6.1.4.1.4874.2.2.29.1.1.7	TruthValue	read-write	Set this object to true(1) in order to have client-to-client route reflection enabled.
U32 juniBgpClusterId	1.3.6.1.4.1.4874.2.2.29.1.1.8	Unsigned32	read-write	The cluster ID. When this object is zero, the router ID will be used.
U32 juniBgpConfederationId	1.3.6.1.4.1.4874.2.2.29.1.1.9	Unsigned32	read-write	The confederation ID. When this object is zero, the router is not in a confederation.
T/F juniBgpMissingAsWorst	1.3.6.1.4.1.4874.2.2.29.1.1.10	TruthValue	read-write	If this object is set to true(1) routes without a MED attribute are considered worse than routes with a MED attribute. If this object is set to false(0) routes without a MED attribute are considered better than routes with a MED attribute.
JUN juniBgpResetAllConnectionType	1.3.6.1.4.1.4874.2.2.29.1.1.11	JuniBgpResetConnectionType	read-write	Writing a value to this object causes all sessions to all peers to be cleared; the value determines what type of clear is executed (hard clear, soft clear in, soft clear out, etc.). Reading this object has no effect and always returns resetTypeNoop.
T/F juniBgpAdvertiseInactive	1.3.6.1.4.1.4874.2.2.29.1.1.12	TruthValue	read-write	Set this object to true(1) in order to propagate received BGP routes which are not the best route in the IP forwarding table.
T/F juniBgpEnforceFirstAs	1.3.6.1.4.1.4874.2.2.29.1.1.13	TruthValue	read-write	Set this object to true(1) in order to check whether the first AS number in the AS-path in routes from EBGP peers is consistent with the AS number of the peer.
T/F juniBgpConfedCompareMed	1.3.6.1.4.1.4874.2.2.29.1.1.14	TruthValue	read-write	Set this object to true(1) in order to compare metrics for paths from neighors of different sub-ASs in the same confederation.
I32 juniBgpGlobalRetryInterval	1.3.6.1.4.1.4874.2.2.29.1.1.15	Integer32	read-write	The default number of seconds before BGP retries to establish an outgoing BGP session.
I32 juniBgpGlobalConfigKeepAliveInterval	1.3.6.1.4.1.4874.2.2.29.1.1.16	Integer32	read-write	Default time interval in seconds for the KeepAlive timer for all peers. Zero means don't send KeepAlive messages.
I32 juniBgpGlobalConfigHoldTime	1.3.6.1.4.1.4874.2.2.29.1.1.17	Integer32	read-write	Default time interval in seconds for the Hold timer for all peers. Zero means don't expect KeepAlive message to be received.
I32 juniBgpGlobalAsOriginationInterval	1.3.6.1.4.1.4874.2.2.29.1.1.18	Integer32	read-write	Default time interval in seconds for the MinASOriginationInterval timer for all peers.
I32 juniBgpExternalAdvertisementInterval	1.3.6.1.4.1.4874.2.2.29.1.1.19	Integer32	read-write	Default time interval in seconds for the MinRouteAdvertisementInterval timer for all external peers.
T/F juniBgpGlobalRibOutEnabled	1.3.6.1.4.1.4874.2.2.29.1.1.20	TruthValue	read-write	Set this object to true(1) in order to enable RIB-out by default for all peers, or to false(2) to disable RIB-out by default for all peers.
T/F juniBgpOverloadShutdown	1.3.6.1.4.1.4874.2.2.29.1.1.21	TruthValue	read-write	Set this object to true(1) for BGP to shut itself down when it runs out of memory. Set this object to false(2) for BGP to continue running (with incomplete information) when it runs out of memory.
T/F juniBgpLogNeighborChanges	1.3.6.1.4.1.4874.2.2.29.1.1.22	TruthValue	read-write	Set this object to true(1) for BGP log a message whenever a peer enters or leaves the established state.
T/F juniBgpFastExternalFallover	1.3.6.1.4.1.4874.2.2.29.1.1.23	TruthValue	read-write	Set this object to true(1) for BGP to immediately bring down any directly adjacent EBGP session on a link down.
I32 juniBgpInternalAdvertisementInterval	1.3.6.1.4.1.4874.2.2.29.1.1.24	Integer32	read-write	Default time interval in seconds for the MinRouteAdvertisementInterval timer for all internal peers.
I32 juniBgpMaxAsLimit	1.3.6.1.4.1.4874.2.2.29.1.1.25	Integer32	read-write	Maximum length of received AS-path. Received routes with an AS-path longer than this are not placed in the IP forwarding table and are not propagated to other peers. Zero means no maximum length.
INT juniBgpOperationalState	1.3.6.1.4.1.4874.2.2.29.1.1.26	INTEGER	read-only	The BGP instance operational state.
INT juniBgpPreviousOperationalState	1.3.6.1.4.1.4874.2.2.29.1.1.27	INTEGER	read-only	The BGP instance previous operational state.
T/F juniBgpAutomaticRouteTargetFilter	1.3.6.1.4.1.4874.2.2.29.1.1.28	TruthValue	read-write	Set this object to true(1) for BGP to enable automatic route-target filtering.
T/F juniBgpDefaultIPv4Unicast	1.3.6.1.4.1.4874.2.2.29.1.1.29	TruthValue	read-write	Set this object to true(1) for BGP to automatically activate peers in the IPv4 unicast address family.
T/F juniBgpRedistributeInternal	1.3.6.1.4.1.4874.2.2.29.1.1.30	TruthValue	read-write	Set this object to true(1) for BGP to automatically redistribute iBGP routes to IGP protocols.
JUN juniBgpFourOctetLocalAsNumber	1.3.6.1.4.1.4874.2.2.29.1.1.31	JuniBgpFourOctetAsNumber	read-write	The four-octet local autonomous system number. This attribute replaces the old two-octet local autonomous system number.
STR juniBgpConfederationPeersFilterList	1.3.6.1.4.1.4874.2.2.29.1.1.32	DisplayString	read-write	The confederation peers filter-list contains the name of an as-path access-list. Every neighbor whose remote-AS number matches this as-path access-list is considered a confederation peer. An empty string means that no confederation peers filter-list is configured.
BIT juniBgpUnconfiguredAttributes	1.3.6.1.4.1.4874.2.2.29.1.1.33	Bits	read-write	On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
T/F juniBgpAdvertiseBestExternalToInternal	1.3.6.1.4.1.4874.2.2.29.1.1.34	TruthValue	read-write	If this object is set to true(1) then BGP advertises the best route received from external (and confederation) peers to internal peers. If this object is set to false(2) then BGP advertises the best route received from all peers to internal peers except if the best route was received from an internal peer in which case BGP doesn't advertise any route to internal peers.
T/F juniBgpGracefulRestartEnabled	1.3.6.1.4.1.4874.2.2.29.1.1.35	TruthValue	read-write	Set this object to true(1) to enable BGP graceful restart.
I32 juniBgpGracefulRestartRestartTime	1.3.6.1.4.1.4874.2.2.29.1.1.36	Integer32	read-write	The restart-time advertised in graceful-restart capabilities sent to all peers. This is the estimated time (in seconds) it will take for the BGP session to be re-established after a restart. This can be used to speed up routing convergence by the peer in case that this BGP speaker does not come back after a restart. This value is used by all peers unless overridden by juniBgpPeerGroupGracefulRestartRestartTime or juniBgpPeerGracefulRestartRestartTime.
I32 juniBgpGracefulRestartStalePathsTime	1.3.6.1.4.1.4874.2.2.29.1.1.37	Integer32	read-write	The maximum amount of time in seconds we keep stale routes after a session goes down. This value is used for all peers unless it has been overridden by juniBgpPeerGroupGracefulRestartStalePathsTime or juniBgpPeerGracefulRestartStalePathsTime.
I32 juniBgpGracefulRestartPathSelectionDeferTimeLimit	1.3.6.1.4.1.4874.2.2.29.1.1.38	Integer32	read-write	The maximum amount of time in seconds route selection is deferred after a restart.
T/F juniBgpPlatformSupportsNonStopForwarding	1.3.6.1.4.1.4874.2.2.29.1.1.39	TruthValue	read-only	Does this platform support non-stop forwarding?
T/F juniBgpDeviceCanPreserveForwardingState	1.3.6.1.4.1.4874.2.2.29.1.1.40	TruthValue	read-only	Is this router at this moment able to do a graceful restart (i.e. is it able to switch over from the primary controller to the standby controller without losing forwarding state on the line cards). The router may not be able to do a graceful restart because the platform does not support non-stop forwarding, because there is no secondary controller present, because the secondary controller is not in standby state, etc.
T/F juniBgpLastRestartWasGraceful	1.3.6.1.4.1.4874.2.2.29.1.1.41	TruthValue	read-only	Was the most recent restart graceful? (i.e. was forwarding state preserved on the line cards during the most recent switch-over from the primary controller to the standby controller?)
juniBgpRouteTableStatisticsGroup	1.3.6.1.4.1.4874.2.2.29.1.2
U32 juniBgpBaselineTime	1.3.6.1.4.1.4874.2.2.29.1.2.1	Unsigned32	read-only	The sysUpTime at which the counters were most recently baselined.
G32 juniBgpDestinationCount	1.3.6.1.4.1.4874.2.2.29.1.2.2	Gauge32	read-only	Number of distinct destinations in the local RIB.
G32 juniBgpDestinationMemoryUsed	1.3.6.1.4.1.4874.2.2.29.1.2.3	Gauge32	read-only	Memory used by distinct destinations in the local RIB.
G32 juniBgpRouteCount	1.3.6.1.4.1.4874.2.2.29.1.2.4	Gauge32	read-only	Number of routes in the local RIB.
G32 juniBgpRouteMemoryUsed	1.3.6.1.4.1.4874.2.2.29.1.2.5	Gauge32	read-only	Memory used by routes in the local RIB.
G32 juniBgpSelectedRouteCount	1.3.6.1.4.1.4874.2.2.29.1.2.6	Gauge32	read-only	Number of routes selected for route table installation.
G32 juniBgpPathAttributeCount	1.3.6.1.4.1.4874.2.2.29.1.2.8	Gauge32	read-only	Number of entries in the path attribute database.
G32 juniBgpPathAttributeMemoryUsed	1.3.6.1.4.1.4874.2.2.29.1.2.9	Gauge32	read-only	Memory used by entries in the path attribute database.
G32 juniBgpRouteFlapHistoryCount	1.3.6.1.4.1.4874.2.2.29.1.2.10	Gauge32	read-only	Number of routes with active route flap histories.
G32 juniBgpRouteFlapHistoryMemoryUsed	1.3.6.1.4.1.4874.2.2.29.1.2.11	Gauge32	read-only	Memory used by routes with active route flap histories.
G32 juniBgpSuppressedRouteCount	1.3.6.1.4.1.4874.2.2.29.1.2.12	Gauge32	read-only	Number of routes suppressed due to route flap.
juniBgpConfederationPeerTable	1.3.6.1.4.1.4874.2.2.29.1.3		not-accessible	The Juniper BGP Confederation Peer Table describes the BGP-specific characteristics of confederation peers.
juniBgpConfederationPeerEntry	1.3.6.1.4.1.4874.2.2.29.1.3.1		not-accessible	The BGP Confederation Peer Entry describes BGP-specific characteristics of one confederation peer.
I32 juniBgpConfederationPeerAsNumber	1.3.6.1.4.1.4874.2.2.29.1.3.1.1	Integer32	not-accessible	The AsNumber of this confederation peer.
ROW juniBgpConfederationPeerRowStatus	1.3.6.1.4.1.4874.2.2.29.1.3.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
juniBgpPeerTable	1.3.6.1.4.1.4874.2.2.29.1.4		not-accessible	The Juniper BGP Peer Table describes the BGP-specific characteristics of peers.
juniBgpPeerEntry	1.3.6.1.4.1.4874.2.2.29.1.4.1		not-accessible	The BGP Peer Entry describes BGP-specific characteristics of one peer.
JUN juniBgpPeerVrfName	1.3.6.1.4.1.4874.2.2.29.1.4.1.1	JuniVrfName	not-accessible	The name of the VPN Routing Forwarding (VRF) instance in which this peer is configured. The empty string indicates that this peer is not in a VRF.
IP juniBgpPeerRemoteAddress	1.3.6.1.4.1.4874.2.2.29.1.4.1.2	IpAddress	not-accessible	The remote IP address of this entry's BGP peer.
INT juniBgpPeerAdminStatus	1.3.6.1.4.1.4874.2.2.29.1.4.1.3	INTEGER	read-create	The desired state of the BGP connection. A transition from 'stop' to 'start' will cause the BGP Start Event to be generated. A transition from 'start' to 'stop' will cause the BGP Stop Event to be generated. This parameter can be used to restart BGP peer connections. Care should be used in providing write access to this object without adequate authentication.
INT juniBgpPeerState	1.3.6.1.4.1.4874.2.2.29.1.4.1.4	INTEGER	read-only	The BGP peer connection state.
I32 juniBgpPeerNegotiatedVersion	1.3.6.1.4.1.4874.2.2.29.1.4.1.5	Integer32	read-only	The negotiated version of BGP running between the two peers.
IP juniBgpPeerLocalAddress	1.3.6.1.4.1.4874.2.2.29.1.4.1.6	IpAddress	read-only	The local IP address of this entry's BGP connection.
IP juniBgpPeerLocalAddressMask	1.3.6.1.4.1.4874.2.2.29.1.4.1.7	IpAddress	read-only	The local IP address mask of this entry's BGP connection.
I32 juniBgpPeerLocalPort	1.3.6.1.4.1.4874.2.2.29.1.4.1.8	Integer32	read-only	The local port for the TCP connection between the BGP peers.
I32 juniBgpPeerRemoteAsNumber	1.3.6.1.4.1.4874.2.2.29.1.4.1.9	Integer32	read-create	Deprecated. The peer's autonomous system number. This object has been replaced by juniBgpPeerFourOctetRemoteAsNumber. It is still possible to get and set this object, but if the actual remote AS number is greater than 65535, getting this object returns 23456 (AS-TRANS).
I32 juniBgpPeerRemotePort	1.3.6.1.4.1.4874.2.2.29.1.4.1.10	Integer32	read-only	The remote port for the TCP connection between the BGP peers. Note that the objects bgpPeerLocalAddr, bgpPeerLocalPort, bgpPeerRemoteAddr and bgpPeerRemotePort provide the appropriate reference to the standard MIB TCP connection table.
C32 juniBgpPeerInUpdatesEx	1.3.6.1.4.1.4874.2.2.29.1.4.1.11	Counter32	read-only	The number of BGP UPDATE messages received on this connection. This object should be initialized to zero (0) when the connection is established.
C32 juniBgpPeerOutUpdates	1.3.6.1.4.1.4874.2.2.29.1.4.1.12	Counter32	read-only	The number of BGP UPDATE messages transmitted on this connection. This object should be initialized to zero (0) when the connection is established.
C32 juniBgpPeerInTotalMessages	1.3.6.1.4.1.4874.2.2.29.1.4.1.13	Counter32	read-only	The total number of messages received from the remote peer on this connection. This object should be initialized to zero when the connection is established.
C32 juniBgpPeerOutTotalMessages	1.3.6.1.4.1.4874.2.2.29.1.4.1.14	Counter32	read-only	The total number of messages transmitted to the remote peer on this connection. This object should be initialized to zero when the connection is established.
OCT juniBgpPeerLastErrorCode	1.3.6.1.4.1.4874.2.2.29.1.4.1.15	OCTET STRING	read-only	The last error code and subcode seen by this peer on this connection. If no error has occurred, this field is zero. Otherwise, the first byte of this two byte OCTET STRING contains the error code, and the second byte contains the subcode.
STR juniBgpPeerLastResetReason	1.3.6.1.4.1.4874.2.2.29.1.4.1.16	DisplayString	read-only	The string representing the last error code seen by this peer on this connection. If no error has occurred, this string is null.
C32 juniBgpPeerFsmEstablishedTransitions	1.3.6.1.4.1.4874.2.2.29.1.4.1.17	Counter32	read-only	The total number of times the BGP FSM transitioned into the established state.
G32 juniBgpPeerFsmEstablishedTime	1.3.6.1.4.1.4874.2.2.29.1.4.1.18	Gauge32	read-only	This timer indicates how long (in seconds) this peer has been in the Established state or how long since this peer was last in the Established state. It is set to zero when a new peer is configured or the router is booted.
I32 juniBgpPeerRetryInterval	1.3.6.1.4.1.4874.2.2.29.1.4.1.19	Integer32	read-create	Time interval in seconds for the ConnectRetry timer. The suggested value for this timer is 120 seconds.
I32 juniBgpPeerHoldTime	1.3.6.1.4.1.4874.2.2.29.1.4.1.20	Integer32	read-only	Time interval in seconds for the Hold Timer established with the peer. The value of this object is calculated by this BGP speaker by using the smaller of the value in bgpPeerHoldTimeConfigured and the Hold Time received in the OPEN message. This value must be at lease three seconds if it is not zero (0) in which case the Hold Timer has not been established with the peer, or, the value of bgpPeerHoldTimeConfigured is zero (0).
I32 juniBgpPeerKeepAliveInterval	1.3.6.1.4.1.4874.2.2.29.1.4.1.21	Integer32	read-only	Time interval in seconds for the KeepAlive timer established with the peer. The value of this object is calculated by this BGP speaker such that, when compared with bgpPeerHoldTime, it has the same proportion as what bgpPeerKeepAliveConfigured has when compared with bgpPeerHoldTimeConfigured. If the value of this object is zero (0), it indicates that the KeepAlive timer has not been established with the peer, or, the value of bgpPeerKeepAliveConfigured is zero (0).
I32 juniBgpPeerConfigHoldTime	1.3.6.1.4.1.4874.2.2.29.1.4.1.22	Integer32	read-create	Time interval in seconds for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BGP speaker, and is compared with the Hold Time field in an OPEN message received from the peer when determining the Hold Time (bgpPeerHoldTime) with the peer. This value must not be less than three seconds if it is not zero (0) in which case the Hold Time is NOT to be established with the peer. The suggested value for this timer is 90 seconds.
I32 juniBgpPeerConfigKeepAliveInterval	1.3.6.1.4.1.4874.2.2.29.1.4.1.23	Integer32	read-create	Time interval in seconds for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages' frequency relative to the value specified in bgpPeerHoldTimeConfigured; the actual time interval for the KEEPALIVE messages is indicated by bgpPeerKeepAlive. A reasonable maximum value for this timer would be configured to be one third of that of bgpPeerHoldTimeConfigured. If the value of this object is zero (0), no periodical KEEPALIVE messages are sent to the peer after the BGP connection has been established. The suggested value for this timer is 30 seconds.
I32 juniBgpPeerAsOriginationInterval	1.3.6.1.4.1.4874.2.2.29.1.4.1.24	Integer32	read-create	Time interval in seconds for the MinASOriginationInterval timer. The suggested value for this timer is 10 seconds.
I32 juniBgpPeerAdvertisementInterval	1.3.6.1.4.1.4874.2.2.29.1.4.1.25	Integer32	read-create	Time interval in seconds for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds.
G32 juniBgpPeerInUpdateElapsedTime	1.3.6.1.4.1.4874.2.2.29.1.4.1.26	Gauge32	read-only	Elapsed time in seconds since the last BGP UPDATE message was received from the peer. Each time bgpPeerInUpdates is incremented, the value of this object is set to zero (0).
STR juniBgpPeerDescription	1.3.6.1.4.1.4874.2.2.29.1.4.1.27	DisplayString	read-create	Peer textual description.
IP juniBgpPeerRemoteIdentifier	1.3.6.1.4.1.4874.2.2.29.1.4.1.28	IpAddress	read-only	Peer's remote router ID.
U32 juniBgpPeerWeight	1.3.6.1.4.1.4874.2.2.29.1.4.1.29	Unsigned32	read-create	The weight assigned to routes learned from peer.
T/F juniBgpPeerEbgpMultihop	1.3.6.1.4.1.4874.2.2.29.1.4.1.30	TruthValue	read-create	The EBGP multihop is enabled.
I32 juniBgpPeerEbgpMultihopTtl	1.3.6.1.4.1.4874.2.2.29.1.4.1.31	Integer32	read-create	Maximum number of hops to the external peer (only relevant if EBGP multihop turned on).
IP juniBgpPeerUpdateSource	1.3.6.1.4.1.4874.2.2.29.1.4.1.32	IpAddress	read-create	The source IP address for peer connections.
OCT juniBgpPeerMd5Password	1.3.6.1.4.1.4874.2.2.29.1.4.1.33	OCTET STRING	read-create	The password for MD5 authentication. Reading this object always results in an OCTET STRING of length zero.
U32 juniBgpPeerMaxUpdateSize	1.3.6.1.4.1.4874.2.2.29.1.4.1.34	Unsigned32	read-create	The maximum size in bytes of transmitted UPDATE messages.
INT juniBgpPeerType	1.3.6.1.4.1.4874.2.2.29.1.4.1.35	INTEGER	read-only	The type of peer.
T/F juniBgpPeerReceivedCapabilitiesOption	1.3.6.1.4.1.4874.2.2.29.1.4.1.36	TruthValue	read-only	The peer sent the capabilities optional parameter in its open message.
T/F juniBgpPeerReceivedCapabilityMultiProtocol	1.3.6.1.4.1.4874.2.2.29.1.4.1.37	TruthValue	read-only	The peer has advertised the multi-protocol capability to us.
T/F juniBgpPeerReceivedCapabilityRouteRefresh	1.3.6.1.4.1.4874.2.2.29.1.4.1.38	TruthValue	read-only	The peer has advertised the route-refresh capability to us.
T/F juniBgpPeerReceivedCapabilityRouteRefreshCisco	1.3.6.1.4.1.4874.2.2.29.1.4.1.39	TruthValue	read-only	The peer has advertised the route-refresh-cisco capability to us.
JUN juniBgpPeerResetConnectionType	1.3.6.1.4.1.4874.2.2.29.1.4.1.40	JuniBgpResetConnectionType	read-create	Writing a value to this object causes the session to the peer to be cleared; the value determines what type of clear is executed (hard clear, soft clear in, soft clear out, etc.). Reading this object has no effect and always returns resetTypeNoop.
ROW juniBgpPeerRowStatus	1.3.6.1.4.1.4874.2.2.29.1.4.1.41	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
I32 juniBgpPeerLocalAsNumber	1.3.6.1.4.1.4874.2.2.29.1.4.1.42	Integer32	read-create	Deprecated. The local autonomous system number to be used for this peer. Value zero (0) means that the global local automous system number (as specified in the object juniBgpPeerLocalAsNumber) is used. This object has been replaced by juniBgpPeerFourOctetLocalAsNumber. It is still possible to get and set this object, but if the actual local AS number is greater than 65535, getting this object returns AS-TRANS (23456).
JUN juniBgpPeerFourOctetRemoteAsNumber	1.3.6.1.4.1.4874.2.2.29.1.4.1.43	JuniBgpFourOctetAsNumber	read-create	The peer's four-octet autonomous system number.
JUN juniBgpPeerFourOctetLocalAsNumber	1.3.6.1.4.1.4874.2.2.29.1.4.1.44	JuniBgpFourOctetAsNumber	read-create	The four-octet local autonomous system number to be used for this peer. Value zero (0) means that the global local automous system number (as specified in the object juniBgpPeerFourOctetLocalAsNumber) is used.
T/F juniBgpPeerReceivedCapabilityFourOctetAsNumbers	1.3.6.1.4.1.4874.2.2.29.1.4.1.45	TruthValue	read-only	The peer has advertised the four-octet-as-numbers capability to us.
T/F juniBgpPeerReceivedCapabilityDynamicCapabilityNeg	1.3.6.1.4.1.4874.2.2.29.1.4.1.46	TruthValue	read-only	The peer has advertised the dynamic-capability-negotiation capability to us.
T/F juniBgpPeerShouldAdvertiseCapabilitiesOption	1.3.6.1.4.1.4874.2.2.29.1.4.1.47	TruthValue	read-create	Set this object to true if the capabilities option should be included in OPEN messages sent to this peer. Even if this object is set to true, BGP may decide not to include the capabilities option in OPEN messages sent to this peer (for example when it is detected that the peer does not support capability negotiation). The juniBgpPeerSentCapabilitiesOption can be used to determine whether or not the OPEN message sent to the peer actually contained the capabilities option.
T/F juniBgpPeerShouldAdvertiseCapabilityRouteRefresh	1.3.6.1.4.1.4874.2.2.29.1.4.1.48	TruthValue	read-create	Set this object to true if the route-refresh capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the route-refresh capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the route-refresh capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityRouteRefresh can be used to determine whether or not the capability was actually advertised to the peer.
T/F juniBgpPeerShouldAdvertiseCapabilityRouteRefreshCisco	1.3.6.1.4.1.4874.2.2.29.1.4.1.49	TruthValue	read-create	Set this object to true if the route-refresh-cisco capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the route-refresh-cisco capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the route-refresh-cisco capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityRouteRefreshCisco can be used to determine whether or not the capability was actually advertised to the peer.
T/F juniBgpPeerShouldAdvertiseCapabilityFourOctetAsNumbers	1.3.6.1.4.1.4874.2.2.29.1.4.1.50	TruthValue	read-create	Set this object to true if the four-octet-as-numbers capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the four-octet-as-numbers capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the four-octet-as-numbers capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityFourOctetAsNumbers can be used to determine whether or not the capability was actually advertised to the peer.
T/F juniBgpPeerShouldAdvertiseCapabilityDynamicCapabilityNeg	1.3.6.1.4.1.4874.2.2.29.1.4.1.51	TruthValue	read-create	Set this object to true if the dynamic-capability-negotiation capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the dynamic-capability-negotiation capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the dynamic-capability-negotiation capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityDynamicCapabilityNeg can be used to determine whether or not the capability was actually advertised to the peer.
T/F juniBgpPeerSentCapabilitiesOption	1.3.6.1.4.1.4874.2.2.29.1.4.1.52	TruthValue	read-only	We sent the capabilities optional parameter in the OPEN message to this peer.
T/F juniBgpPeerSentCapabilityMultiProtocol	1.3.6.1.4.1.4874.2.2.29.1.4.1.53	TruthValue	read-only	We advertised the multi-protocol capability to this peer.
T/F juniBgpPeerSentCapabilityRouteRefresh	1.3.6.1.4.1.4874.2.2.29.1.4.1.54	TruthValue	read-only	We advertised the route-refresh capability to this peer.
T/F juniBgpPeerSentCapabilityRouteRefreshCisco	1.3.6.1.4.1.4874.2.2.29.1.4.1.55	TruthValue	read-only	We advertised the route-refresh-cisco capability to this peer.
T/F juniBgpPeerSentCapabilityFourOctetAsNumbers	1.3.6.1.4.1.4874.2.2.29.1.4.1.56	TruthValue	read-only	We advertised the four-octet-as-numbers capability to this peer.
T/F juniBgpPeerSentCapabilityDynamicCapabilityNeg	1.3.6.1.4.1.4874.2.2.29.1.4.1.57	TruthValue	read-only	We advertised the dynamic-capability-negotiation capability to this peer.
T/F juniBgpPeerReceivedUnsupportedOptionalParameterNotification	1.3.6.1.4.1.4874.2.2.29.1.4.1.58	TruthValue	read-only	We received an unsupported optional parameter notification from this peer. This indicates that the peer does not support capability negotiation. When this object is set to true, we do not include the capabilities optional parameter in OPEN messages sent to this peer. A hard clear of the session is needed to retry sending the capabilities optional parameter.
T/F juniBgpPeerReceivedUnsupportedCapabilityNotification	1.3.6.1.4.1.4874.2.2.29.1.4.1.59	TruthValue	read-only	We received an unsupported capability notification from this peer. This often happens because the peer did not recognize a capability which we advertised to the peer and that peer incorrectly send back an unsupported capability notification (the peer should ignore the unsupported capability instead). When this object is set to true, we do not advertise capabilities that the peer does not support.
BIT juniBgpPeerUnconfiguredAttributes	1.3.6.1.4.1.4874.2.2.29.1.4.1.60	Bits	read-create	On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
OCT juniBgpPeerSiteOfOrigin	1.3.6.1.4.1.4874.2.2.29.1.4.1.61	OCTET STRING	read-create	The site-of-origin. This site-of-origin is added to the extended communities for all routes received from the peer. When sending routes to this peer all routes with this extended community are filtered. The null extended community (all 8 bytes zero) means that no site-of-origin is configured for this peer. It is not allowed to set this object to any extended community other than a site-of-origin type of extended community or null.
T/F juniBgpPeerLenient	1.3.6.1.4.1.4874.2.2.29.1.4.1.62	TruthValue	read-create	Enable Lenient behavior for this peer so that it is more tolerant of finite state machine errors and malformed messages received from the remote peer and avoids terminating the peer session whenever possible.
T/F juniBgpPeerReceivedCapabilityOldDynamicCapabilityNeg	1.3.6.1.4.1.4874.2.2.29.1.4.1.63	TruthValue	read-only	The peer has advertised the old deprecated dynamic-capability- negotiation capability to us.
T/F juniBgpPeerShouldAdvertiseCapabilityOldDynamicCapabilityNeg	1.3.6.1.4.1.4874.2.2.29.1.4.1.64	TruthValue	read-create	Set this object to true if the deprecated-dynamic-capability- negotiation capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the deprecated-dynamic-capability-negotiation capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the deprecated-dynamic-capability-negotiation capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityOldDynamicCapabilityNeg can be used to determine whether or not the capability was actually advertised to the peer.
T/F juniBgpPeerSentCapabilityOldDynamicCapabilityNeg	1.3.6.1.4.1.4874.2.2.29.1.4.1.65	TruthValue	read-only	We advertised the old-dynamic-capability-negotiation capability to this peer.
T/F juniBgpPeerPassive	1.3.6.1.4.1.4874.2.2.29.1.4.1.66	TruthValue	read-create	Set this object to true(1) to make this a passive peer.
T/F juniBgpPeerDynamic	1.3.6.1.4.1.4874.2.2.29.1.4.1.67	TruthValue	read-only	This object return true(1) if this is a dynamically created peer or false(2) if this is a configured peer.
T/F juniBgpPeerShouldAdvertiseCapabilityGracefulRestart	1.3.6.1.4.1.4874.2.2.29.1.4.1.68	TruthValue	read-create	Set this object to true if the graceful-restart capability should be advertised to all peers. Even if this object is set to true, BGP may decide not to advertise the graceful-restart capability to a peer (for example when graceful-restart is not enabled or when it is detected that the peer does not support capability negotiation). The juniBgpPeerSentCapabilityGracefulRestart can be used to determine whether or not the capability was actually advertised to the peer.
T/F juniBgpPeerSentCapabilityGracefulRestart	1.3.6.1.4.1.4874.2.2.29.1.4.1.69	TruthValue	read-only	We advertised the graceful-restart capability to this peer.
T/F juniBgpPeerReceivedCapabilityGracefulRestart	1.3.6.1.4.1.4874.2.2.29.1.4.1.70	TruthValue	read-only	The peer has advertised the graceful-restart capability to us.
I32 juniBgpPeerGracefulRestartRestartTime	1.3.6.1.4.1.4874.2.2.29.1.4.1.71	Integer32	read-create	The restart-time advertised in the graceful-restart capability sent to this peer. This is the estimated time (in seconds) it will take for the BGP session to be re-established after a restart. This can be used to speed up routing convergence by the peer in case that this BGP speaker does not come back after a restart. This value (if configured) overrides the global value configured in juniBgpGracefulRestartRestartTime and the value for the peer-group configured in juniBgpPeerGroupGracefulRestartRestartTime.
I32 juniBgpPeerGracefulRestartStalePathsTime	1.3.6.1.4.1.4874.2.2.29.1.4.1.72	Integer32	read-create	The maximum amount of time in seconds we keep stale routes after the session to this peer goes down. This value (if configured) overrides the global value configured in juniBgpGracefulRestartStalePathsTime and the value for the peer-group configured in juniBgpPeerGroupGracefulRestartStalePathsTime.
T/F juniBgpPeerSentGracefulRestartRestartState	1.3.6.1.4.1.4874.2.2.29.1.4.1.73	TruthValue	read-only	Value true(1) indicates that the OPEN message most recently sent to this peer contained the graceful-restart capability with the Restart-State (R) bit in the Restart Flags field set to one (this indicates that BGP has experienced a restart).
T/F juniBgpPeerReceivedGracefulRestartRestartState	1.3.6.1.4.1.4874.2.2.29.1.4.1.74	TruthValue	read-only	Value true(1) indicates that the OPEN message most recently received from this peer contained the graceful-restart capability with the Restart-State (R) bit in the Restart Flags field set to one (this indicates that the peer has experienced a restart).
I32 juniBgpPeerSentGracefulRestartRestartTime	1.3.6.1.4.1.4874.2.2.29.1.4.1.75	Integer32	read-only	The restart time in seconds field in the graceful-restart capability which we sent to the peer.
I32 juniBgpPeerReceivedGracefulRestartRestartTime	1.3.6.1.4.1.4874.2.2.29.1.4.1.76	Integer32	read-only	The restart time in seconds field in the graceful-restart capability which we received from the peer.
I32 juniBgpPeerTimeUntilGracefulRestartRestartTimerExpires	1.3.6.1.4.1.4874.2.2.29.1.4.1.77	Integer32	read-only	If the restart-timer is running this object contains the number of seconds before it will expire. If the restart-timer is not running this object contains zero. The restart-timer is used to limit the amount of time that we are willing to wait for the session to come back up after the peer restarts.
I32 juniBgpPeerTimeUntilGracefulRestartStalePathsTimerExpires	1.3.6.1.4.1.4874.2.2.29.1.4.1.78	Integer32	read-only	If the stale-paths-timer is running this object contains the number of seconds before it will expire. If the stale-paths-timer is not running this object contains zero. The stale-paths-timer is used to limit the amount of time that we are willing continue using stale routes from a peer after that peer restarts.
T/F juniBgpPeerBfdEnabled	1.3.6.1.4.1.4874.2.2.29.1.4.1.79	TruthValue	read-create	Value true(1) the BFD is enabled for this peer.
I32 juniBgpPeerBfdMinTransmitInterval	1.3.6.1.4.1.4874.2.2.29.1.4.1.80	Integer32	read-create	The minimum interval (in milliseconds) between BFD packets sent to the remote BFD speaker. In other words, it specifies the maximum rate at which we are willing to send BFD packets.
I32 juniBgpPeerBfdMinReceiveInterval	1.3.6.1.4.1.4874.2.2.29.1.4.1.81	Integer32	read-create	The minimum interval (in milliseconds) between BFD packets received from the remote BFD speaker. In other words, it specifies the maximum rate at which we are willing to receive BFD packets.
I32 juniBgpPeerBfdMultiplier	1.3.6.1.4.1.4874.2.2.29.1.4.1.82	Integer32	read-create	How many BFD packets can be missed before the BFD session is declared down.
T/F juniBgpPeerBfdSessionUp	1.3.6.1.4.1.4874.2.2.29.1.4.1.83	TruthValue	read-only	Is the BFD session up.
I32 juniBgpPeerBfdDetectionTime	1.3.6.1.4.1.4874.2.2.29.1.4.1.84	Integer32	read-only	The BFD detection time (in milliseconds) negotiated with the remote BFD speaker. In other words, how quickly can a broken connection be detected.
T/F juniBgpPeerIbgpSinglehop	1.3.6.1.4.1.4874.2.2.29.1.4.1.85	TruthValue	read-create	The IBGP single-hop is enabled.
juniBgpPeerProposedAfiSafiPeerTable	1.3.6.1.4.1.4874.2.2.29.1.5		not-accessible	The Juniper BGP PeerProposedAfiSafi Peer Table describes the BGP-specific AFI and SAFIs a peer proposed.
juniBgpPeerProposedAfiSafiPeerEntry	1.3.6.1.4.1.4874.2.2.29.1.5.1		not-accessible	The BGP PeerProposedAfiSafi Peer Entry describes a BGP-specific AFI/SAFIs proposed by one peer.
JUN juniBgpPeerProposedAfiSafiPeerVrfName	1.3.6.1.4.1.4874.2.2.29.1.5.1.1	JuniVrfName	not-accessible	The name of the VPN Routing Forwarding (VRF) instance in which this peer is configured. The empty string indicates that this peer is not in a VRF.
IP juniBgpPeerProposedAfiSafiPeerRemoteAddr	1.3.6.1.4.1.4874.2.2.29.1.5.1.2	IpAddress	not-accessible	The remote IP address of this entry's BGP peer.
JUN juniBgpPeerProposedAfiSafiPeerAfi	1.3.6.1.4.1.4874.2.2.29.1.5.1.3	JuniBgpAfi	not-accessible	The AFI proposed by this peer to us.
JUN juniBgpPeerProposedAfiSafiPeerSafi	1.3.6.1.4.1.4874.2.2.29.1.5.1.4	JuniBgpSafi	not-accessible	The SAFI proposed by this peer to us.
ROW juniBgpPeerProposedAfiSafiPeerRowStatus	1.3.6.1.4.1.4874.2.2.29.1.5.1.5	RowStatus	read-only	Should always be active according to the Row Status convention.
juniBgpLocalProposedAfiSafiPeerTable	1.3.6.1.4.1.4874.2.2.29.1.6		not-accessible	The Juniper BGP LocalProposedAfiSafi Peer Table describes the BGP-specific AFI and SAFIs proposed to the peer.
juniBgpLocalProposedAfiSafiPeerEntry	1.3.6.1.4.1.4874.2.2.29.1.6.1		not-accessible	The BGP LocalProposedAfiSafi Peer Entry describes a BGP-specific AFI/SAFIs proposed to one peer.
JUN juniBgpLocalProposedAfiSafiPeerVrfName	1.3.6.1.4.1.4874.2.2.29.1.6.1.1	JuniVrfName	not-accessible	The name of the VPN Routing Forwarding (VRF) instance in which this peer is configured. The empty string indicates that this peer is not in a VRF.
IP juniBgpLocalProposedAfiSafiPeerRemoteAddr	1.3.6.1.4.1.4874.2.2.29.1.6.1.2	IpAddress	not-accessible	The remote IP address of this entry's BGP peer.
JUN juniBgpLocalProposedAfiSafiPeerAfi	1.3.6.1.4.1.4874.2.2.29.1.6.1.3	JuniBgpAfi	not-accessible	The AFI we proposed to this peer.
JUN juniBgpLocalProposedAfiSafiPeerSafi	1.3.6.1.4.1.4874.2.2.29.1.6.1.4	JuniBgpSafi	not-accessible	The SAFI we proposed to this peer.
ROW juniBgpLocalProposedAfiSafiPeerRowStatus	1.3.6.1.4.1.4874.2.2.29.1.6.1.5	RowStatus	read-only	Should always be active according to the Row Status convention.
juniBgpExchangedAfiSafiPeerTable	1.3.6.1.4.1.4874.2.2.29.1.7		not-accessible	The Juniper BGP PeerExchangedAfiSafi Peer Table describes the BGP-specific AFI and SAFIs a peer exchanged.
juniBgpExchangedAfiSafiPeerEntry	1.3.6.1.4.1.4874.2.2.29.1.7.1		not-accessible	The BGP ExchangedAfiSafi Peer Entry describes a BGP-specific AFI/SAFIs exchanged by one peer.
JUN juniBgpExchangedAfiSafiPeerVrfName	1.3.6.1.4.1.4874.2.2.29.1.7.1.1	JuniVrfName	not-accessible	The name of the VPN Routing Forwarding (VRF) instance in which this peer is configured. The empty string indicates that this peer is not in a VRF.
IP juniBgpExchangedAfiSafiPeerRemoteAddr	1.3.6.1.4.1.4874.2.2.29.1.7.1.2	IpAddress	not-accessible	The remote IP address of this entry's BGP peer.
JUN juniBgpExchangedAfiSafiPeerAfi	1.3.6.1.4.1.4874.2.2.29.1.7.1.3	JuniBgpAfi	not-accessible	The AFI which we exchange with this peer.
JUN juniBgpExchangedAfiSafiPeerSafi	1.3.6.1.4.1.4874.2.2.29.1.7.1.4	JuniBgpSafi	not-accessible	The SAFI which we exchange with this peer.
ROW juniBgpExchangedAfiSafiPeerRowStatus	1.3.6.1.4.1.4874.2.2.29.1.7.1.5	RowStatus	read-only	Should always be active according to the Row Status convention.
juniBgpPeerAddressFamilyTable	1.3.6.1.4.1.4874.2.2.29.1.8		not-accessible	The Juniper BGP Peer Address Family Table describes the BGP-specific attributes of an Address Family for a peer.
juniBgpPeerAddressFamilyEntry	1.3.6.1.4.1.4874.2.2.29.1.8.1		not-accessible	The BGP ExchangedAfiSafi Peer Entry describes a BGP-specific AFI/SAFIs exchanged by one peer.
JUN juniBgpPeerAddressFamilyVrfName	1.3.6.1.4.1.4874.2.2.29.1.8.1.1	JuniVrfName	not-accessible	The name of the VPN Routing Forwarding (VRF) instance in which this peer is configured. The empty string indicates that this peer is not in a VRF.
JUN juniBgpPeerAddressFamilyAfi	1.3.6.1.4.1.4874.2.2.29.1.8.1.2	JuniBgpAfi	not-accessible	The AFI of the address-family in which this peer is configured.
JUN juniBgpPeerAddressFamilySafi	1.3.6.1.4.1.4874.2.2.29.1.8.1.3	JuniBgpSafi	not-accessible	The SAFI of the address-family in which this peer is configured.
IP juniBgpPeerAddressFamilyRemoteAddress	1.3.6.1.4.1.4874.2.2.29.1.8.1.4	IpAddress	not-accessible	The remote IP address of this entry's BGP peer.
STR juniBgpPeerAddressFamilyPeerGroup	1.3.6.1.4.1.4874.2.2.29.1.8.1.5	DisplayString	read-create	Peer group membership (null if none).
T/F juniBgpPeerAddressFamilyDefaultOriginate	1.3.6.1.4.1.4874.2.2.29.1.8.1.6	TruthValue	read-create	Set this object to true(1) in order to advertise a default route to this peer, if present.
T/F juniBgpPeerAddressFamilyNextHopSelf	1.3.6.1.4.1.4874.2.2.29.1.8.1.7	TruthValue	read-create	Set this object to true(1) in order to always advertise this router as the next hop.
T/F juniBgpPeerAddressFamilySendCommunity	1.3.6.1.4.1.4874.2.2.29.1.8.1.8	TruthValue	read-create	Set this object to true(1) in order to send COMMUNITIES attributes in updates.
STR juniBgpPeerAddressFamilyDistributeListIn	1.3.6.1.4.1.4874.2.2.29.1.8.1.9	DisplayString	read-create	The inbound distribute IP access list name.
STR juniBgpPeerAddressFamilyDistributeListOut	1.3.6.1.4.1.4874.2.2.29.1.8.1.10	DisplayString	read-create	The outbound distribute IP access list name.
STR juniBgpPeerAddressFamilyPrefixListIn	1.3.6.1.4.1.4874.2.2.29.1.8.1.11	DisplayString	read-create	The inbound IP prefix list name.
STR juniBgpPeerAddressFamilyPrefixListOut	1.3.6.1.4.1.4874.2.2.29.1.8.1.12	DisplayString	read-create	The outbound IP prefix list name.
STR juniBgpPeerAddressFamilyPrefixTreeIn	1.3.6.1.4.1.4874.2.2.29.1.8.1.13	DisplayString	read-create	The inbound IP prefix tree name.
STR juniBgpPeerAddressFamilyPrefixTreeOut	1.3.6.1.4.1.4874.2.2.29.1.8.1.14	DisplayString	read-create	The outbound IP prefix tree name.
STR juniBgpPeerAddressFamilyFilterListIn	1.3.6.1.4.1.4874.2.2.29.1.8.1.15	DisplayString	read-create	The inbound filter AS path list name.
STR juniBgpPeerAddressFamilyFilterListOut	1.3.6.1.4.1.4874.2.2.29.1.8.1.16	DisplayString	read-create	The outbound filter AS path list name.
STR juniBgpPeerAddressFamilyFilterListWeight	1.3.6.1.4.1.4874.2.2.29.1.8.1.17	DisplayString	read-create	The weight filter AS path list name.
U32 juniBgpPeerAddressFamilyFilterListWeightValue	1.3.6.1.4.1.4874.2.2.29.1.8.1.18	Unsigned32	read-create	The weight to apply on weight filter list matches.
STR juniBgpPeerAddressFamilyRouteMapIn	1.3.6.1.4.1.4874.2.2.29.1.8.1.19	DisplayString	read-create	The inbound route-map name. An empty string means no inbound route-map.
STR juniBgpPeerAddressFamilyRouteMapOut	1.3.6.1.4.1.4874.2.2.29.1.8.1.20	DisplayString	read-create	The outbound route-map name. An empty string means no outbound route-map.
T/F juniBgpPeerAddressFamilyRouteReflectorClient	1.3.6.1.4.1.4874.2.2.29.1.8.1.21	TruthValue	read-create	The peer is a route reflector client.
U32 juniBgpPeerAddressFamilyRouteLimitWarn	1.3.6.1.4.1.4874.2.2.29.1.8.1.22	Unsigned32	read-create	Log a warning if pathCount exceeds this value.
U32 juniBgpPeerAddressFamilyRouteLimitReset	1.3.6.1.4.1.4874.2.2.29.1.8.1.23	Unsigned32	read-create	Reset connection is pathCount exceeds this value.
T/F juniBgpPeerAddressFamilyRouteLimitWarnOnly	1.3.6.1.4.1.4874.2.2.29.1.8.1.24	TruthValue	read-create	Warn, but do not reset, if the path limit is exceeded.
T/F juniBgpPeerAddressFamilyRemovePrivateAs	1.3.6.1.4.1.4874.2.2.29.1.8.1.25	TruthValue	read-create	Remove private AS numbers from AS paths.
STR juniBgpPeerAddressFamilyUnsuppressMap	1.3.6.1.4.1.4874.2.2.29.1.8.1.26	DisplayString	read-create	The unsuppress route-map name. Routes which are sent to this peer and which match this route-map are not subject to suppression by summary-only aggregates. An empty string means no unsuppress route-map.
T/F juniBgpPeerAddressFamilyInboundSoftReconfig	1.3.6.1.4.1.4874.2.2.29.1.8.1.27	TruthValue	read-create	Inbound soft-reconfiguration is enabled. If inbound soft-reconfiguration is enabled we keep a copy of each received route before inbound policy was applied.
JUN juniBgpPeerAddressFamilyResetConnectionType	1.3.6.1.4.1.4874.2.2.29.1.8.1.28	JuniBgpResetConnectionType	read-create	Writing a value to this object causes one individual address family within the session to the peer to be cleared; the value determines what type of clear is executed (hard clear, soft clear in, soft clear out, etc.). Note that hard clearing an address family within a session will bounce the session and thus also affect the other address families in the session. Reading this object has no effect and always returns resetTypeNoop.
ROW juniBgpPeerAddressFamilyRowStatus	1.3.6.1.4.1.4874.2.2.29.1.8.1.29	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
T/F juniBgpPeerAddressFamilyAsOverride	1.3.6.1.4.1.4874.2.2.29.1.8.1.30	TruthValue	read-create	Replace the AS number of the peer by our own AS number in the AS-path attribute in UPDATEs sent to this peer.
I32 juniBgpPeerAddressFamilyAllowAsIn	1.3.6.1.4.1.4874.2.2.29.1.8.1.31	Integer32	read-create	The maximum number of times our own AS number is allowed to occur in a received AS-path before that received route is considered to be a loop and therefore rejected.
T/F juniBgpPeerAddressFamilySendExtendedCommunity	1.3.6.1.4.1.4874.2.2.29.1.8.1.32	TruthValue	read-create	Set this object to true(1) in order to send EXTENDED-COMMUNITIES attributes in updates.
T/F juniBgpPeerAddressFamilyAdvertiseCapPrefixListOrfSend	1.3.6.1.4.1.4874.2.2.29.1.8.1.33	TruthValue	read-create	Set this object to true(1) in order to send PREFIX-LIST ORF SEND CAPABILITY in Open Message.
T/F juniBgpPeerAddressFamilyAdvertiseCapPrefixListOrfReceive	1.3.6.1.4.1.4874.2.2.29.1.8.1.34	TruthValue	read-create	Set this object to true(1) in order to send PREFIX-LIST ORF RECEIVE CAPABILITY in Open Message.
T/F juniBgpPeerAddressFamilyAdvertiseCapPrefixListCiscoOrfSend	1.3.6.1.4.1.4874.2.2.29.1.8.1.35	TruthValue	read-create	Set this object to true(1) in order to send PREFIX-LIST-CISCO ORF SEND CAPABILITY in Open Message.
T/F juniBgpPeerAddressFamilyAdvertiseCapPrefixListCiscoOrfReceive	1.3.6.1.4.1.4874.2.2.29.1.8.1.36	TruthValue	read-create	Set this object to true(1) in order to send PREFIX-LIST-CISCO ORF RECEIVE CAPABILITY in Open Message.
T/F juniBgpPeerAddressFamilyReceivedCapPrefixListOrfSend	1.3.6.1.4.1.4874.2.2.29.1.8.1.37	TruthValue	read-only	The peer has sent PREFIX-LIST ORF SEND CAPABILITY to us for this address family.
T/F juniBgpPeerAddressFamilyReceivedCapPrefixListOrfReceive	1.3.6.1.4.1.4874.2.2.29.1.8.1.38	TruthValue	read-only	The peer has sent PREFIX-LIST ORF RECEIVE CAPABILITY to us for this address family.
T/F juniBgpPeerAddressFamilyReceivedCapPrefixListCiscoOrfSend	1.3.6.1.4.1.4874.2.2.29.1.8.1.39	TruthValue	read-only	The peer has sent PREFIX-LIST-CISCO ORF SEND CAPABILITY to us for this address family.
T/F juniBgpPeerAddressFamilyReceivedCapPrefixListCiscoOrfReceive	1.3.6.1.4.1.4874.2.2.29.1.8.1.40	TruthValue	read-only	The peer has sent PREFIX-LIST-CISCO ORF RECEIVE CAPABILITY to us for this address family.
U32 juniBgpPeerAddressFamilyReceivedOrfEntriesLimit	1.3.6.1.4.1.4874.2.2.29.1.8.1.41	Unsigned32	read-create	Ignore received ORF entries for this address family if count exceeds this value.
STR juniBgpPeerAddressFamilyReceivedPrefixListOrfName	1.3.6.1.4.1.4874.2.2.29.1.8.1.42	DisplayString	read-only	The prefix list name containing ORF entries received from the peer for this address family
T/F juniBgpPeerAddressFamilyMaximumPrefixStrict	1.3.6.1.4.1.4874.2.2.29.1.8.1.43	TruthValue	read-create	If the juniBgpPeerAddressFamilyInboundSoftReconfig object is set to true then routes which were rejected by inbound policy are stored in memory anyway. The juniBgpPeerAddressFamilyMaximumPrefixStrict object determines whether or not these routes count towards the maximum number of routes from the peer (as configured in juniBgpPeerAddressFamilyRouteLimitWarn and/or juniBgpPeerAddressFamilyRouteLimitReset).
BIT juniBgpPeerAddressFamilyUnconfiguredAttributes	1.3.6.1.4.1.4874.2.2.29.1.8.1.44	Bits	read-create	On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
T/F juniBgpPeerAddressFamilySendLabel	1.3.6.1.4.1.4874.2.2.29.1.8.1.45	TruthValue	read-create	Send labeled prefixes to this peer for this address-family.
STR juniBgpPeerAddressFamilyDefaultOriginateRouteMap	1.3.6.1.4.1.4874.2.2.29.1.8.1.46	DisplayString	read-create	The route-map to apply to the default route which is advertised to this peer as a result of setting juniBgpPeerAddressFamilyDefaultOriginate to true. An empty string means that no route-map is applied.
T/F juniBgpPeerAddressFamilySentCapabilityGracefulRestart	1.3.6.1.4.1.4874.2.2.29.1.8.1.47	TruthValue	read-only	Value true(1) means that an AFI-SAFI block for this address-family was included in the graceful-restart capability which we sent to this peer.
T/F juniBgpPeerAddressFamilyReceivedCapabilityGracefulRestart	1.3.6.1.4.1.4874.2.2.29.1.8.1.48	TruthValue	read-only	Value true(1) means that an AFI-SAFI block for this address-family was included in the graceful-restart capability which we received from this peer.
T/F juniBgpPeerAddressFamilySentForwardingStatePreserved	1.3.6.1.4.1.4874.2.2.29.1.8.1.49	TruthValue	read-only	Value true(1) indicates that the OPEN message most recently sent to this peer contained the graceful-restart capability which included an AFI-SAFI block for this address-family with the Forwarding-State (F) bit in the Flags for Address Family field set to one (this indicates that forwarding state has been preserved for the address family during the previous restart).
T/F juniBgpPeerAddressFamilyReceivedForwardingStatePreserved	1.3.6.1.4.1.4874.2.2.29.1.8.1.50	TruthValue	read-only	Value true(1) indicates that the OPEN message most recently received from this peer contained the graceful-restart capability which included an AFI-SAFI block for this address-family with the Forwarding-State (F) bit in the Flags for Address Family field set to one (this indicates that the peer preserved forwarding state for the address family during the previous restart).
T/F juniBgpPeerAddressFamilySentEndOfRibMarker	1.3.6.1.4.1.4874.2.2.29.1.8.1.51	TruthValue	read-only	Value true(1) indicates that we have sent an End-of-RIB marker for this address-family to this peer since the session became established.
T/F juniBgpPeerAddressFamilyReceivedEndOfRibMarker	1.3.6.1.4.1.4874.2.2.29.1.8.1.52	TruthValue	read-only	Value true(1) indicates that we have received an End-of-RIB marker for this address-family from this peer since the session became established.
T/F juniBgpPeerAddressFamilyWaitingForEndOfRibBeforeFlushStaleRoutes	1.3.6.1.4.1.4874.2.2.29.1.8.1.53	TruthValue	read-only	Value true(1) indicates that we are still waiting for an End-of-RIB marker from this peer before flushing all remaining stale routes from the address-family.
T/F juniBgpPeerAddressFamilyWaitingForEndOfRibBeforePathSelection	1.3.6.1.4.1.4874.2.2.29.1.8.1.54	TruthValue	read-only	Value true(1) indicates that we are still waiting for an End-of-RIB marker from this peer before we stop deferring path selection for this address-family.
T/F juniBgpPeerAddressFamilyNextHopUnchanged	1.3.6.1.4.1.4874.2.2.29.1.8.1.55	TruthValue	read-create	Set this object to true(1) in order to always advertise the the next-hop unchanged to this peer for this address-family.
juniBgpPeerGroupTable	1.3.6.1.4.1.4874.2.2.29.1.9		not-accessible	The Juniper BGP Peer Group Table describes the BGP-specific characteristics of peer groups.
juniBgpPeerGroupEntry	1.3.6.1.4.1.4874.2.2.29.1.9.1		not-accessible	The BGP Peer Group Entry describes BGP-specific characteristics of one peer group.
JUN juniBgpPeerGroupVrfName	1.3.6.1.4.1.4874.2.2.29.1.9.1.1	JuniVrfName	not-accessible	The name of the VPN Routing Forwarding (VRF) instance in which this peer-group is configured. The empty string indicates that this peer-group is not in a VRF.
STR juniBgpPeerGroupGroupName	1.3.6.1.4.1.4874.2.2.29.1.9.1.2	DisplayString	not-accessible	The name of the Peer group this instance configures.
INT juniBgpPeerGroupAdminStatus	1.3.6.1.4.1.4874.2.2.29.1.9.1.3	INTEGER	read-create	The desired state of the BGP connection. A transition from 'stop' to 'start' will cause the BGP Start Event to be generated. A transition from 'start' to 'stop' will cause the BGP Stop Event to be generated. This parameter can be used to restart BGP peer connections. Care should be used in providing write access to this object without adequate authentication.
I32 juniBgpPeerGroupRemoteAsNumber	1.3.6.1.4.1.4874.2.2.29.1.9.1.4	Integer32	read-create	Deprecated. The peer's autonomous system number. This object has been replaced by juniBgpPeerGroupFourOctetRemoteAsNumber. It is still possible to get and set this object, but if the actual remote AS number is greater than 65535, getting this object returns 23456 (AS-TRANS).
I32 juniBgpPeerGroupRetryInterval	1.3.6.1.4.1.4874.2.2.29.1.9.1.5	Integer32	read-create	Time interval in seconds for the ConnectRetry timer. The suggested value for this timer is 120 seconds.
I32 juniBgpPeerGroupConfigHoldTime	1.3.6.1.4.1.4874.2.2.29.1.9.1.6	Integer32	read-create	Time interval in seconds for the Hold Time configured for this BGP speaker with this peer. This value is placed in an OPEN message sent to this peer by this BGP speaker, and is compared with the Hold Time field in an OPEN message received from the peer when determining the Hold Time (bgpPeerHoldTime) with the peer. This value must not be less than three seconds if it is not zero (0) in which case the Hold Time is NOT to be established with the peer. The suggested value for this timer is 90 seconds.
I32 juniBgpPeerGroupConfigKeepAliveInterval	1.3.6.1.4.1.4874.2.2.29.1.9.1.7	Integer32	read-create	Time interval in seconds for the KeepAlive timer configured for this BGP speaker with this peer. The value of this object will only determine the KEEPALIVE messages' frequency relative to the value specified in bgpPeerHoldTimeConfigured; the actual time interval for the KEEPALIVE messages is indicated by bgpPeerKeepAlive. A reasonable maximum value for this timer would be configured to be one third of that of bgpPeerHoldTimeConfigured. If the value of this object is zero (0), no periodical KEEPALIVE messages are sent to the peer after the BGP connection has been established. The suggested value for this timer is 30 seconds.
I32 juniBgpPeerGroupAsOriginationInterval	1.3.6.1.4.1.4874.2.2.29.1.9.1.8	Integer32	read-create	Time interval in seconds for the MinASOriginationInterval timer. The suggested value for this timer is 10 seconds.
I32 juniBgpPeerGroupAdvertisementInterval	1.3.6.1.4.1.4874.2.2.29.1.9.1.9	Integer32	read-create	Time interval in seconds for the MinRouteAdvertisementInterval timer. The suggested value for this timer is 30 seconds.
STR juniBgpPeerGroupDescription	1.3.6.1.4.1.4874.2.2.29.1.9.1.10	DisplayString	read-create	Peer textual description.
U32 juniBgpPeerGroupWeight	1.3.6.1.4.1.4874.2.2.29.1.9.1.11	Unsigned32	read-create	The weight assigned to routes learned from peer.
T/F juniBgpPeerGroupEbgpMultihop	1.3.6.1.4.1.4874.2.2.29.1.9.1.12	TruthValue	read-create	The EBGP multihop is enabled.
I32 juniBgpPeerGroupEbgpMultihopTtl	1.3.6.1.4.1.4874.2.2.29.1.9.1.13	Integer32	read-create	Maximum number of hops to the external peer (only relevant if EBGP multihop turned on).
IP juniBgpPeerGroupUpdateSource	1.3.6.1.4.1.4874.2.2.29.1.9.1.14	IpAddress	read-create	The source IP address for peer connections.
OCT juniBgpPeerGroupMd5Password	1.3.6.1.4.1.4874.2.2.29.1.9.1.15	OCTET STRING	read-create	The password for MD5 authentication. Reading this object always results in an OCTET STRING of length zero.
U32 juniBgpPeerGroupMaxUpdateSize	1.3.6.1.4.1.4874.2.2.29.1.9.1.16	Unsigned32	read-create	The maximum size in bytes of transmitted UPDATE messages.
JUN juniBgpPeerGroupResetConnectionType	1.3.6.1.4.1.4874.2.2.29.1.9.1.17	JuniBgpResetConnectionType	read-create	Writing a value to this object causes the sessions to all peers in the peer-group to be cleared; the value determines what type of clear is executed (hard clear, soft clear in, soft clear out, etc.). Reading this object has no effect and always returns resetTypeNoop.
ROW juniBgpPeerGroupRowStatus	1.3.6.1.4.1.4874.2.2.29.1.9.1.18	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
I32 juniBgpPeerGroupLocalAsNumber	1.3.6.1.4.1.4874.2.2.29.1.9.1.19	Integer32	read-create	Deprecated. The local autonomous system number to be used for members. of this peer-group. Value zero (0) means that the global local automous system number (as specified in the object juniBgpPeerGroupLocalAsNumber) is used. This object has been replaced by juniBgpPeerGroupFourOctetLocalAsNumber. It is still possible to get and set this object, but if the actual local AS number is greater than 65535, getting this object returns AS-TRANS (23456).
JUN juniBgpPeerGroupFourOctetRemoteAsNumber	1.3.6.1.4.1.4874.2.2.29.1.9.1.20	JuniBgpFourOctetAsNumber	read-create	The peer's four-octet autonomous system number.
JUN juniBgpPeerGroupFourOctetLocalAsNumber	1.3.6.1.4.1.4874.2.2.29.1.9.1.21	JuniBgpFourOctetAsNumber	read-create	The four-octet local autonomous system number to be used for this peer. Value zero (0) means that the global local automous system number (as specified in the object juniBgpPeerGroupFourOctetLocalAsNumber) is used.
T/F juniBgpPeerGroupShouldAdvertiseCapabilitiesOption	1.3.6.1.4.1.4874.2.2.29.1.9.1.22	TruthValue	read-create	Set this object to true if the capabilities option should be included in OPEN messages sent to this peer. Even if this object is set to true, BGP may decide not to include the capabilities option in OPEN messages sent to this peer (for example when it is detected that the peer does not support capability negotiation). The juniBgpPeerSentCapabilitiesOption can be used to determine whether or not the OPEN message sent to the peer actually contained the capabilities option.
T/F juniBgpPeerGroupShouldAdvertiseCapabilityRouteRefresh	1.3.6.1.4.1.4874.2.2.29.1.9.1.23	TruthValue	read-create	Set this object to true if the route-refresh capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the route-refresh capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the route-refresh capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityRouteRefresh can be used to determine whether or not the capability was actually advertised to the peer.
T/F juniBgpPeerGroupShouldAdvertiseCapabilityRouteRefreshCisco	1.3.6.1.4.1.4874.2.2.29.1.9.1.24	TruthValue	read-create	Set this object to true if the route-refresh-cisco capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the route-refresh-cisco capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the route-refresh-cisco capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityRouteRefreshCisco can be used to determine whether or not the capability was actually advertised to the peer.
T/F juniBgpPeerGroupShouldAdvertiseCapabilityFourOctetAsNumbers	1.3.6.1.4.1.4874.2.2.29.1.9.1.25	TruthValue	read-create	Set this object to true if the four-octet-as-numbers capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the four-octet-as-numbers capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the four-octet-as-numbers capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityFourOctetAsNumbers can be used to determine whether or not the capability was actually advertised to the peer.
T/F juniBgpPeerGroupShouldAdvertiseCapabilityDynamicCapabilityNeg	1.3.6.1.4.1.4874.2.2.29.1.9.1.26	TruthValue	read-create	Set this object to true if the dynamic-capability-negotiation capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the dynamic-capability-negotiation capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the dynamic-capability-negotiation capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityDynamicCapabilityNeg can be used to determine whether or not the capability was actually advertised to the peer.
BIT juniBgpPeerGroupUnconfiguredAttributes	1.3.6.1.4.1.4874.2.2.29.1.9.1.27	Bits	read-create	On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
OCT juniBgpPeerGroupSiteOfOrigin	1.3.6.1.4.1.4874.2.2.29.1.9.1.28	OCTET STRING	read-create	The site-of-origin. This site-of-origin is added to the extended communities for all routes received from the peer. When sending routes to this peer-group all routes with this extended community are filtered. The null extended community (all 8 bytes zero) means that no site-of-origin is configured for this peer. It is not allowed to set this object to any extended community other than a site-of-origin type of extended community or null.
T/F juniBgpPeerGroupLenient	1.3.6.1.4.1.4874.2.2.29.1.9.1.29	TruthValue	read-create	Enable Lenient behavior for member peers so that they are more tolerant of finite state machine errors and malformed messages received from the remote peer and avoid terminating the peer session whenever possible.
T/F juniBgpPeerGroupShouldAdvertiseCapabilityOldDynamicCapabilityNeg	1.3.6.1.4.1.4874.2.2.29.1.9.1.30	TruthValue	read-create	Set this object to true if the deprecated-dynamic-capability- negotiation capability should be advertised to this peer. Even if this object is set to true, BGP may decide not to advertise the deprecated-dynamic-capability-negotiation capability to this peer (for example when it is detected that the peer does not support capability negotiation or when it is detected that the peer does not support the deprecated-dynamic-capability-negotiation capability and incorrectly sends an unsupported capability notification). The juniBgpPeerSentCapabilityOldDynamicCapabilityNeg can be used to determine whether or not the capability was actually advertised to the peer.
T/F juniBgpPeerGroupPassive	1.3.6.1.4.1.4874.2.2.29.1.9.1.31	TruthValue	read-create	Set this object to true(1) to make members of this peer-group passive.
INT juniBgpPeerGroupConfiguredPeerType	1.3.6.1.4.1.4874.2.2.29.1.9.1.32	INTEGER	read-create	The type of the members of the peer-group.
STR juniBgpPeerGroupAllowAccessListName	1.3.6.1.4.1.4874.2.2.29.1.9.1.33	DisplayString	read-create	The name of the access-list for promiscuous peers. When an incoming connection arrives whose remote address matches this access-list the connection is accepted and a dynamic peer is created. An empty string means that promiscuous peers are disabled for this peer-group.
U32 juniBgpPeerGroupAllowMaxPeers	1.3.6.1.4.1.4874.2.2.29.1.9.1.34	Unsigned32	read-create	The maximum number of dynamic peers for this peer-group. Zero means that there is no limit.
U32 juniBgpPeerGroupCurrentDynamicPeerCount	1.3.6.1.4.1.4874.2.2.29.1.9.1.35	Unsigned32	read-only	The current number of dynamic peers for this peer-group.
U32 juniBgpPeerGroupHighWaterMarkDynamicPeerCount	1.3.6.1.4.1.4874.2.2.29.1.9.1.36	Unsigned32	read-only	The high water mark for the number of dynamic peers for this peer-group.
U32 juniBgpPeerGroupRejectedDynamicPeerCount	1.3.6.1.4.1.4874.2.2.29.1.9.1.37	Unsigned32	read-only	The number of connection attempts for dynamic peers that were rejected because the number number of dynamic peers was reached.
T/F juniBgpPeerGroupShouldAdvertiseCapabilityGracefulRestart	1.3.6.1.4.1.4874.2.2.29.1.9.1.38	TruthValue	read-create	Set this object to true if the graceful-restart capability should be advertised to all members of the peer-group.
I32 juniBgpPeerGroupGracefulRestartRestartTime	1.3.6.1.4.1.4874.2.2.29.1.9.1.39	Integer32	read-create	The restart-time advertised in the graceful-restart capability sent to members of this peer-group. This is the estimated time (in seconds) it will take for the BGP session to be re-established after a restart. This can be used to speed up routing convergence by the peer in case that this BGP speaker does not come back after a restart. This value (if configured) overrides the global value configured in juniBgpGracefulRestartRestartTime.
I32 juniBgpPeerGroupGracefulRestartStalePathsTime	1.3.6.1.4.1.4874.2.2.29.1.9.1.40	Integer32	read-create	The maximum amount of time in seconds we keep stale routes after the session to a member of this peer-group goes down. This value (if configured) overrides the global value configured in juniBgpGracefulRestartStalePathsTime.
T/F juniBgpPeerGroupBfdEnabled	1.3.6.1.4.1.4874.2.2.29.1.9.1.41	TruthValue	read-create	Value true(1) the BFD is enabled for this peer-group.
I32 juniBgpPeerGroupBfdMinTransmitInterval	1.3.6.1.4.1.4874.2.2.29.1.9.1.42	Integer32	read-create	The minimum interval (in milliseconds) between BFD packets sent to the remote BFD speaker. In other words, it specifies the maximum rate at which we are willing to send BFD packets.
I32 juniBgpPeerGroupBfdMinReceiveInterval	1.3.6.1.4.1.4874.2.2.29.1.9.1.43	Integer32	read-create	The minimum interval (in milliseconds) between BFD packets received from the remote BFD speaker. In other words, it specifies the maximum rate at which we are willing to receive BFD packets.
I32 juniBgpPeerGroupBfdMultiplier	1.3.6.1.4.1.4874.2.2.29.1.9.1.44	Integer32	read-create	How many BFD packets can be missed before the BFD session is declared down.
T/F juniBgpPeerGroupIbgpSinglehop	1.3.6.1.4.1.4874.2.2.29.1.9.1.45	TruthValue	read-create	The IBGP single-hop is enabled.
juniBgpPeerGroupAddressFamilyTable	1.3.6.1.4.1.4874.2.2.29.1.10		not-accessible	The Juniper BGP Peer Group Address Family Table describes the BGP-specific attributes of an Address Family for a peer group.
juniBgpPeerGroupAddressFamilyEntry	1.3.6.1.4.1.4874.2.2.29.1.10.1		not-accessible	The BGP Peer Group Address Family Entry describes.
JUN juniBgpPeerGroupAddressFamilyVrfName	1.3.6.1.4.1.4874.2.2.29.1.10.1.1	JuniVrfName	not-accessible	The name of the VPN Routing Forwarding (VRF) instance in which this peer-group is configured. The empty string indicates that this peer-group is not in a VRF.
JUN juniBgpPeerGroupAddressFamilyAfi	1.3.6.1.4.1.4874.2.2.29.1.10.1.2	JuniBgpAfi	not-accessible	The AFI of the address-family in which this peer-group is configured.
JUN juniBgpPeerGroupAddressFamilySafi	1.3.6.1.4.1.4874.2.2.29.1.10.1.3	JuniBgpSafi	not-accessible	The SAFI of the address-family in which this peer-group is configured.
STR juniBgpPeerGroupGroupAddressFamilyGroupName	1.3.6.1.4.1.4874.2.2.29.1.10.1.4	DisplayString	not-accessible	The name of the Peer group this instance configures.
T/F juniBgpPeerGroupAddressFamilyDefaultOriginate	1.3.6.1.4.1.4874.2.2.29.1.10.1.5	TruthValue	read-create	Set this object to true(1) in order to advertise a default route to this peer, if present.
T/F juniBgpPeerGroupAddressFamilyNextHopSelf	1.3.6.1.4.1.4874.2.2.29.1.10.1.6	TruthValue	read-create	Set this object to true(1) in order to always advertise this router as the next hop.
T/F juniBgpPeerGroupAddressFamilySendCommunity	1.3.6.1.4.1.4874.2.2.29.1.10.1.7	TruthValue	read-create	Set this object to true(1) in order to send COMMUNITIES attributes in updates.
STR juniBgpPeerGroupAddressFamilyDistributeListIn	1.3.6.1.4.1.4874.2.2.29.1.10.1.8	DisplayString	read-create	The inbound distribute IP access list name.
STR juniBgpPeerGroupAddressFamilyDistributeListOut	1.3.6.1.4.1.4874.2.2.29.1.10.1.9	DisplayString	read-create	The outbound distribute IP access list name.
STR juniBgpPeerGroupAddressFamilyPrefixListIn	1.3.6.1.4.1.4874.2.2.29.1.10.1.10	DisplayString	read-create	The inbound IP prefix list name.
STR juniBgpPeerGroupAddressFamilyPrefixListOut	1.3.6.1.4.1.4874.2.2.29.1.10.1.11	DisplayString	read-create	The outbound IP prefix list name.
STR juniBgpPeerGroupAddressFamilyPrefixTreeIn	1.3.6.1.4.1.4874.2.2.29.1.10.1.12	DisplayString	read-create	The inbound IP prefix tree name.
STR juniBgpPeerGroupAddressFamilyPrefixTreeOut	1.3.6.1.4.1.4874.2.2.29.1.10.1.13	DisplayString	read-create	The outbound IP prefix tree name.
STR juniBgpPeerGroupAddressFamilyFilterListIn	1.3.6.1.4.1.4874.2.2.29.1.10.1.14	DisplayString	read-create	The inbound filter AS path list name.
STR juniBgpPeerGroupAddressFamilyFilterListOut	1.3.6.1.4.1.4874.2.2.29.1.10.1.15	DisplayString	read-create	The outbound filter AS path list name.
STR juniBgpPeerGroupAddressFamilyFilterListWeight	1.3.6.1.4.1.4874.2.2.29.1.10.1.16	DisplayString	read-create	The weight filter AS path list name.
U32 juniBgpPeerGroupAddressFamilyFilterListWeightValue	1.3.6.1.4.1.4874.2.2.29.1.10.1.17	Unsigned32	read-create	The weight to apply on weight filter list matches.
STR juniBgpPeerGroupAddressFamilyRouteMapIn	1.3.6.1.4.1.4874.2.2.29.1.10.1.18	DisplayString	read-create	The inbound route-map name. An empty string means no inbound route-map.
STR juniBgpPeerGroupAddressFamilyRouteMapOut	1.3.6.1.4.1.4874.2.2.29.1.10.1.19	DisplayString	read-create	The outbound route-map name. An empty string means no outbound route-map.
T/F juniBgpPeerGroupAddressFamilyRouteReflectorClient	1.3.6.1.4.1.4874.2.2.29.1.10.1.20	TruthValue	read-create	The peer is a route reflector client.
U32 juniBgpPeerGroupAddressFamilyRouteLimitWarn	1.3.6.1.4.1.4874.2.2.29.1.10.1.21	Unsigned32	read-create	Log a warning if pathCount exceeds this value.
U32 juniBgpPeerGroupAddressFamilyRouteLimitReset	1.3.6.1.4.1.4874.2.2.29.1.10.1.22	Unsigned32	read-create	Reset connection is pathCount exceeds this value.
T/F juniBgpPeerGroupAddressFamilyRouteLimitWarnOnly	1.3.6.1.4.1.4874.2.2.29.1.10.1.23	TruthValue	read-create	Warn, but do not reset, if the path limit is exceeded.
T/F juniBgpPeerGroupAddressFamilyRemovePrivateAs	1.3.6.1.4.1.4874.2.2.29.1.10.1.24	TruthValue	read-create	Remove private AS numbers from AS paths.
STR juniBgpPeerGroupAddressFamilyUnsuppressMap	1.3.6.1.4.1.4874.2.2.29.1.10.1.25	DisplayString	read-create	The unsuppress route-map name. Routes which are sent to this peer and which match this route-map are not subject to suppression by summary-only aggregates. An empty string means no unsuppress route-map.
T/F juniBgpPeerGroupAddressFamilyInboundSoftReconfig	1.3.6.1.4.1.4874.2.2.29.1.10.1.26	TruthValue	read-create	Inbound soft-reconfiguration is enabled. If inbound soft-reconfiguration is enabled we keep a copy of each received route before inbound policy was applied.
JUN juniBgpPeerGroupAddressFamilyResetConnectionType	1.3.6.1.4.1.4874.2.2.29.1.10.1.27	JuniBgpResetConnectionType	read-create	Writing a value to this object causes one individual address family within the sessions to all peers in the peer-group to be cleared; the value determines what type of clear is executed (hard clear, soft clear in, soft clear out, etc.). Note that hard clearing an address family within a session will bounce the session and thus also affect the other address families in the session. Reading this object has no effect and always returns resetTypeNoop.
ROW juniBgpPeerGroupAddressFamilyRowStatus	1.3.6.1.4.1.4874.2.2.29.1.10.1.28	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
T/F juniBgpPeerGroupAddressFamilyAsOverride	1.3.6.1.4.1.4874.2.2.29.1.10.1.29	TruthValue	read-create	Replace the AS number of the peer by our own AS number in the AS-path attribute in UPDATEs sent to this peer-group.
I32 juniBgpPeerGroupAddressFamilyAllowAsIn	1.3.6.1.4.1.4874.2.2.29.1.10.1.30	Integer32	read-create	The maximum number of times our own AS number is allowed to occur in a received AS-path before that received route is considered to be a loop and therefore rejected.
T/F juniBgpPeerGroupAddressFamilySendExtendedCommunity	1.3.6.1.4.1.4874.2.2.29.1.10.1.31	TruthValue	read-create	Set this object to true(1) in order to send EXTENDED-COMMUNITIES attributes in updates.
T/F juniBgpPeerGroupAddressFamilyAdvertiseCapPrefixListOrfSend	1.3.6.1.4.1.4874.2.2.29.1.10.1.32	TruthValue	read-create	Set this object to true(1) in order to send PREFIX-LIST ORF SEND CAPABILITY in Open Message.
T/F juniBgpPeerGroupAddressFamilyAdvertiseCapPrefixListCiscoOrfSend	1.3.6.1.4.1.4874.2.2.29.1.10.1.33	TruthValue	read-create	Set this object to true(1) in order to send PREFIX-LIST-CISCO ORF SEND CAPABILITY in Open Message.
T/F juniBgpPeerGroupAddressFamilyMaximumPrefixStrict	1.3.6.1.4.1.4874.2.2.29.1.10.1.34	TruthValue	read-create	If the juniBgpPeerGroupAddressFamilyInboundSoftReconfig object is set to true then routes which were rejected by inbound policy are stored in memory anyway. The juniBgpPeerGroupAddressFamilyMaximumPrefixStrict object determines whether or not these routes count towards the maximum number of routes from the peer-group members (as configured in juniBgpPeerGroupAddressFamilyRouteLimitWarn and/or juniBgpPeerGroupAddressFamilyRouteLimitReset).
BIT juniBgpPeerGroupAddressFamilyUnconfiguredAttributes	1.3.6.1.4.1.4874.2.2.29.1.10.1.35	Bits	read-create	On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
T/F juniBgpPeerGroupAddressFamilySendLabel	1.3.6.1.4.1.4874.2.2.29.1.10.1.36	TruthValue	read-create	Send labeled prefixes to this peer for this address-family.
STR juniBgpPeerGroupAddressFamilyDefaultOriginateRouteMap	1.3.6.1.4.1.4874.2.2.29.1.10.1.37	DisplayString	read-create	The route-map to apply to the default route which is advertised to this peer-group as a result of setting juniBgpPeerGroupAddressFamilyDefaultOriginate to true. An empty string means that no route-map is applied.
T/F juniBgpPeerGroupAddressFamilyNextHopUnchanged	1.3.6.1.4.1.4874.2.2.29.1.10.1.38	TruthValue	read-create	Set this object to true(1) in order to always advertise the next-hop unchanged to this peer-group in this address-family.
juniBgpRouteFlapHistoryTable	1.3.6.1.4.1.4874.2.2.29.1.12		not-accessible	The obsolete BGP Route Flap History Table contained information about recorded route flap events. This table has been replaced by the juniBgpNewRouteFlapHistoryTable.
juniBgpRouteFlapHistoryEntry	1.3.6.1.4.1.4874.2.2.29.1.12.1		not-accessible	An instance in the list of route flap events.
INT juniBgpRouteFlapState	1.3.6.1.4.1.4874.2.2.29.1.12.1.1	INTEGER	read-only	Current state: stateAvailable(1) - indicates path is available stateSuppressedReachable(2) - indicates path is suppressed, destination is reachable stateSuppressedUnreachable(3) - indicates path in suppressed, destination is not reachable
U32 juniBgpRouteFlapFigureOfMerit	1.3.6.1.4.1.4874.2.2.29.1.12.1.2	Unsigned32	read-only	Calculated figure-of-merit.
U32 juniBgpRouteFlapRemainingTime	1.3.6.1.4.1.4874.2.2.29.1.12.1.3	Unsigned32	read-only	Number of seconds until reuse or removal.
U32 juniBgpRouteFlapSuppressThreshold	1.3.6.1.4.1.4874.2.2.29.1.12.1.4	Unsigned32	read-only	Damping cutoff threshold (scaled).
U32 juniBgpRouteFlapReuseThreshold	1.3.6.1.4.1.4874.2.2.29.1.12.1.5	Unsigned32	read-only	Damping reuse threshold (scaled).
U32 juniBgpRouteFlapMaxHoldDownTime	1.3.6.1.4.1.4874.2.2.29.1.12.1.6	Unsigned32	read-only	Maximum route holddown time (seconds).
U32 juniBgpRouteFlapHalfLifeReachable	1.3.6.1.4.1.4874.2.2.29.1.12.1.7	Unsigned32	read-only	Figure of merit half life for reachable routes (seconds).
U32 juniBgpRouteFlapHalfLifeUnreachable	1.3.6.1.4.1.4874.2.2.29.1.12.1.8	Unsigned32	read-only	Figure of merit half life for unreachable routes (seconds).
juniBgpRouteTable	1.3.6.1.4.1.4874.2.2.29.1.13		not-accessible	The obsolete BGP-4 Received Path Attribute Table contained additional information about paths to destination networks received from all BGP4 peers. This table has been replaced by the juniBgpNewRouteTable.
juniBgpRouteEntry	1.3.6.1.4.1.4874.2.2.29.1.13.1		not-accessible	Additional information about a path to a network.
IP juniBgpRouteOriginatorId	1.3.6.1.4.1.4874.2.2.29.1.13.1.1	IpAddress	read-only	The Originator-ID path attribute of the route if present. The juniBgpRouteOriginatorIdPresent object indicates whether the Originator-ID path attribute is present.
T/F juniBgpRouteAtomicAggregatePresent	1.3.6.1.4.1.4874.2.2.29.1.13.1.2	TruthValue	read-only	Atomic-Aggregate path attribute is present.
T/F juniBgpRouteMedPresent	1.3.6.1.4.1.4874.2.2.29.1.13.1.3	TruthValue	read-only	The Multi-Exit-Discriminator path attribute is present.
T/F juniBgpRouteLocalPrefPresent	1.3.6.1.4.1.4874.2.2.29.1.13.1.4	TruthValue	read-only	The Local-Pref path attribute is present.
T/F juniBgpRouteAggregatorPresent	1.3.6.1.4.1.4874.2.2.29.1.13.1.5	TruthValue	read-only	The Aggregator path attribute is present.
T/F juniBgpRouteCommunitiesPresent	1.3.6.1.4.1.4874.2.2.29.1.13.1.6	TruthValue	read-only	The Communities path attribute is present.
T/F juniBgpRouteOriginatorIdPresent	1.3.6.1.4.1.4874.2.2.29.1.13.1.7	TruthValue	read-only	The Originator-ID path attribute is present.
T/F juniBgpRouteClusterListPresent	1.3.6.1.4.1.4874.2.2.29.1.13.1.8	TruthValue	read-only	The Cluster-List path attribute is present.
U32 juniBgpRouteWeight	1.3.6.1.4.1.4874.2.2.29.1.13.1.9	Unsigned32	read-only	The weight of the route.
JUN juniBgpRouteVrfName	1.3.6.1.4.1.4874.2.2.29.1.13.1.10	JuniVrfName	not-accessible	The name of the VPN Routing Forwarding (VRF) instance in which this route is present. The empty string indicates that this route is not in a VRF.
JUN juniBgpRouteAfi	1.3.6.1.4.1.4874.2.2.29.1.13.1.11	JuniBgpAfi	not-accessible	The AFI of the address-family in which this route is present.
JUN juniBgpRouteSafi	1.3.6.1.4.1.4874.2.2.29.1.13.1.12	JuniBgpSafi	not-accessible	The SAFI of the address-family in which this route is present.
IP juniBgpRoutePeer	1.3.6.1.4.1.4874.2.2.29.1.13.1.13	IpAddress	not-accessible	The IP address of the peer from which the route was received. This object has value 0.0.0.0 is the route was a locally originated route.
I32 juniBgpRouteIpAddrPrefixLen	1.3.6.1.4.1.4874.2.2.29.1.13.1.14	Integer32	not-accessible	Length in bits of the IP address prefix of the route.
IP juniBgpRouteIpAddrPrefix	1.3.6.1.4.1.4874.2.2.29.1.13.1.15	IpAddress	not-accessible	The IP address prefix of the route. This object is an IP address containing the prefix with length specified by juniBgpNewRouteIpAddrPrefixLen. Any bits beyond the length specified by juniBgpNewRouteIpAddrPrefixLen are zeroed.
INT juniBgpRouteRouteType	1.3.6.1.4.1.4874.2.2.29.1.13.1.16	INTEGER	not-accessible	The type of the route.
INT juniBgpRouteOrigin	1.3.6.1.4.1.4874.2.2.29.1.13.1.17	INTEGER	read-only	The value of the Origin path attribute.
OCT juniBgpRouteASPathSegment	1.3.6.1.4.1.4874.2.2.29.1.13.1.18	OCTET STRING	read-only	The value of the AS-path path attribute (as encoded in the received update message).
IP juniBgpRouteNextHop	1.3.6.1.4.1.4874.2.2.29.1.13.1.19	IpAddress	read-only	The value of the Next-Hop path attribute.
U32 juniBgpRouteMultiExitDisc	1.3.6.1.4.1.4874.2.2.29.1.13.1.20	Unsigned32	read-only	The value of the Multi-Exit-Discriminator path attribute if present. The juniBgpRouteMedPresent object indicates whether the Multi-Exit-Discriminator path attribute is present.
U32 juniBgpRouteLocalPref	1.3.6.1.4.1.4874.2.2.29.1.13.1.21	Unsigned32	read-only	The value of the Local-Pref path attribute if present. The juniBgpRouteLocalPrefPresent object indicates whether the Local-Pref path attribute is present.
INT juniBgpRouteAtomicAggregate	1.3.6.1.4.1.4874.2.2.29.1.13.1.22	INTEGER	read-only	Whether or not the local system has selected a less specific route without selecting a more specific route.
I32 juniBgpRouteAggregatorAS	1.3.6.1.4.1.4874.2.2.29.1.13.1.23	Integer32	read-only	The value of the AS field in the Aggregator path attribute if present. The juniBgpRouteAggregatorPresent object indicates whether the Aggregator path attribute is present.
IP juniBgpRouteAggregatorAddress	1.3.6.1.4.1.4874.2.2.29.1.13.1.24	IpAddress	read-only	The value of the address field in the Aggregator path attribute if present. The juniBgpRouteAggregatorPresent object indicates whether the Aggregator path attribute is present.
T/F juniBgpRouteBestInIpRouteTable	1.3.6.1.4.1.4874.2.2.29.1.13.1.25	TruthValue	read-only	When BGP places a routes in the IP route table, that route may not be used for forwarding traffic if there are other routes (e.g. IGP routes or static routes) to that same prefix with a better administrative distance in the IP route table. This object indicates whether or not the BGP route in the IP route table is the best route (and hence is used for forwarding traffic).
OCT juniBgpRouteUnknown	1.3.6.1.4.1.4874.2.2.29.1.13.1.26	OCTET STRING	read-only	One or more path attributes not understood by this BGP4 speaker. Size zero (0) indicates the absence of such attribute(s). Octets beyond the maximum size, if any, are not recorded by this object.
T/F juniBgpRouteExtendedCommunitiesPresent	1.3.6.1.4.1.4874.2.2.29.1.13.1.27	TruthValue	read-only	Is the Extended-Communities path attribute present?
T/F juniBgpRouteValid	1.3.6.1.4.1.4874.2.2.29.1.13.1.28	TruthValue	read-only	Is the route valid? The route is declared invalid if there is something wrong with it which is not serious enough for sending a notification, but it serious enough for not placing it in the IP route table or propagating it to other peers (for example the next-hop of the route is a local address).
INT juniBgpRouteSuppressedBy	1.3.6.1.4.1.4874.2.2.29.1.13.1.29	INTEGER	read-only	Indicates whether or not the route is suppressed, and if so why: suppressedByNothing - Route is not suppressed. suppressedByAggregate - Route is suppressed by a summary-only aggregate. suppressedByAutoSummary - Route is suppressed by an auto-summary. suppressedByDampening - Route is suppressed as a result of route-flap dampening.
T/F juniBgpRouteNextHopReachable	1.3.6.1.4.1.4874.2.2.29.1.13.1.30	TruthValue	read-only	Is the indirect next-hop of the route reachable (i.e. can the indirect next-hop of the route be resolved to at least one direct next-hop)?
T/F juniBgpRouteSynchronizedWithIgp	1.3.6.1.4.1.4874.2.2.29.1.13.1.31	TruthValue	read-only	Is the route is synchronized (i.e. is there is an IGP route to the same prefix in the IP route table)?
T/F juniBgpRoutePlaceInIpRouteTable	1.3.6.1.4.1.4874.2.2.29.1.13.1.32	TruthValue	read-only	Has a BGP route for this prefix been placed in the IP route table?
T/F juniBgpRouteAdvertiseToExternalPeers	1.3.6.1.4.1.4874.2.2.29.1.13.1.33	TruthValue	read-only	Should this route be advertised to external peers?
T/F juniBgpRouteAdvertiseToInternalPeers	1.3.6.1.4.1.4874.2.2.29.1.13.1.34	TruthValue	read-only	Should this route be advertised to internal peers?
OCT juniBgpRouteDistinguisher	1.3.6.1.4.1.4874.2.2.29.1.13.1.35	OCTET STRING	read-only	The Route Distinguisher (RD) of the route. This object has an undefined value for non-VPN routes.
U32 juniBgpRouteMplsLabel	1.3.6.1.4.1.4874.2.2.29.1.13.1.36	Unsigned32	read-only	The MPLS label for the route.
U32 juniBgpRouteNextHopMetric	1.3.6.1.4.1.4874.2.2.29.1.13.1.37	Unsigned32	read-only	The metric of direct next-hop of this BGP route.
juniBgpRouteCommunityTable	1.3.6.1.4.1.4874.2.2.29.1.14		not-accessible	The obsolete BGP-4 Path Community Table contained information about communities within destination networks received from all BGP4 peers. This table has been replaced by the juniBgpNewRouteCommunityTable.
juniBgpRouteCommunityEntry	1.3.6.1.4.1.4874.2.2.29.1.14.1		not-accessible	Community attribute information within a path to a network.
U32 juniBgpRouteCommunityNumber	1.3.6.1.4.1.4874.2.2.29.1.14.1.1	Unsigned32	read-only	The community number.
juniBgpRouteClusterIdTable	1.3.6.1.4.1.4874.2.2.29.1.15		not-accessible	The obsolete BGP-4 Path ClusterId Table contained information about router reflector cluster IDs. This table has been replaced by the juniBgpNewRouteClusterIdTable.
juniBgpRouteClusterIdEntry	1.3.6.1.4.1.4874.2.2.29.1.15.1		not-accessible	ClusterId attribute information within a path to a network.
U32 juniBgpRouteClusterId	1.3.6.1.4.1.4874.2.2.29.1.15.1.1	Unsigned32	read-only	The cluster id.
juniBgpNetworkTable	1.3.6.1.4.1.4874.2.2.29.1.16		not-accessible	The BGP Network Table controls what networks are originated by this BGP router.
juniBgpNetworkEntry	1.3.6.1.4.1.4874.2.2.29.1.16.1		not-accessible	An instance in the list of networks originated by this BGP router.
JUN juniBgpNetworkVrfName	1.3.6.1.4.1.4874.2.2.29.1.16.1.1	JuniVrfName	not-accessible	The name of the VPN Routing Forwarding (VRF) instance in which this network is configured. The empty string indicates that this network is not in a VRF.
JUN juniBgpNetworkAfi	1.3.6.1.4.1.4874.2.2.29.1.16.1.2	JuniBgpAfi	not-accessible	The AFI of the address-family in which this network is configured.
JUN juniBgpNetworkSafi	1.3.6.1.4.1.4874.2.2.29.1.16.1.3	JuniBgpSafi	not-accessible	The SAFI of the address-family in which this network is configured.
IP juniBgpNetworkIpAddrPrefix	1.3.6.1.4.1.4874.2.2.29.1.16.1.4	IpAddress	not-accessible	An IP address prefix in the Network Layer Reachability Information field. This object is an IP address containing the prefix with length specified by bgpRouteIpAddrPrefixLen. Any bits beyond the length specified by bgpRouteIpAddrPrefixLen are zeroed.
I32 juniBgpNetworkIpAddrPrefixLen	1.3.6.1.4.1.4874.2.2.29.1.16.1.5	Integer32	not-accessible	Length in bits of the IP address prefix in the Network Layer Reachability Information field.
T/F juniBgpNetworkBackdoor	1.3.6.1.4.1.4874.2.2.29.1.16.1.6	TruthValue	read-create	Set this object to true(1) in order to enable BGP backdoor in this network. This object can only be set at row creation.
ROW juniBgpNetworkRowStatus	1.3.6.1.4.1.4874.2.2.29.1.16.1.7	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
T/F juniBgpNetworkWeightSpecified	1.3.6.1.4.1.4874.2.2.29.1.16.1.8	TruthValue	read-create	If this object is set to true(1) then the BGP weight of this network is set to the value specified in juniBgpNetworkWeightValue. This object can only be set at row creation.
I32 juniBgpNetworkWeight	1.3.6.1.4.1.4874.2.2.29.1.16.1.9	Integer32	read-create	If juniBgpNetworkWeight specified is set to true(1) then this object specifies the weight of the network. Otherwise the weight of the network is determined by the IGP metric of the prefix. This object can only be set at row creation.
STR juniBgpNetworkRouteMap	1.3.6.1.4.1.4874.2.2.29.1.16.1.10	DisplayString	read-create	The name of the route-map used to set the path attributes of this network. A zero length route-map name means don't use a route-map for this. This object can only be set at row creation.
BIT juniBgpNetworkUnconfiguredAttributes	1.3.6.1.4.1.4874.2.2.29.1.16.1.11	Bits	read-create	On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
juniBgpAggregateTable	1.3.6.1.4.1.4874.2.2.29.1.17		not-accessible	The BGP Aggregate Table controls the consolidation of route information.
juniBgpAggregateEntry	1.3.6.1.4.1.4874.2.2.29.1.17.1		not-accessible	An instance in the list of route aggregation.
JUN juniBgpAggregateVrfName	1.3.6.1.4.1.4874.2.2.29.1.17.1.1	JuniVrfName	not-accessible	The name of the VPN Routing Forwarding (VRF) instance in which this aggregate is configured. The empty string indicates that this aggregate is not in a VRF.
JUN juniBgpAggregateAfi	1.3.6.1.4.1.4874.2.2.29.1.17.1.2	JuniBgpAfi	not-accessible	The AFI of the address-family in which this aggregate is configured.
JUN juniBgpAggregateSafi	1.3.6.1.4.1.4874.2.2.29.1.17.1.3	JuniBgpSafi	not-accessible	The SAFI of the address-family in which this aggregate is configured.
IP juniBgpAggregateIpAddrPrefix	1.3.6.1.4.1.4874.2.2.29.1.17.1.4	IpAddress	not-accessible	An IP address prefix in the Network Layer Reachability Information field. This object is an IP address containing the prefix with length specified by bgpRouteIpAddrPrefixLen. Any bits beyond the length specified by bgpRouteIpAddrPrefixLen are zeroed.
I32 juniBgpAggregateIpAddrPrefixLen	1.3.6.1.4.1.4874.2.2.29.1.17.1.5	Integer32	not-accessible	Length in bits of the IP address prefix in the Network Layer Reachability Information field.
T/F juniBgpAggregateAsSet	1.3.6.1.4.1.4874.2.2.29.1.17.1.6	TruthValue	read-create	Set this object to true(1) in order to generate AS_set path information by creating an aggregate entry that consists of all elements contained in all paths that are being summarized. This object can only be set at row creation.
T/F juniBgpAggregateSummaryOnly	1.3.6.1.4.1.4874.2.2.29.1.17.1.7	TruthValue	read-create	Set this object to true(1) in order to filter specific routes from updates. By doing that, advertisements of more specific routes will be suppressed to all neighbors. This object can only be set at row creation.
STR juniBgpAggregateAttributeMap	1.3.6.1.4.1.4874.2.2.29.1.17.1.8	DisplayString	read-create	The name of the route-map used to set the attributes of the aggregate An empty string means no route-map for this purpose.
STR juniBgpAggregateAdvertiseMap	1.3.6.1.4.1.4874.2.2.29.1.17.1.9	DisplayString	read-create	The name of the route-map used to select routes covered by the aggregate (for as-set aggregates the path attributes of the aggregate route are created by summarizing the path attributes of the covered routes). An empty string means no route-map for this purpose.
ROW juniBgpAggregateRowStatus	1.3.6.1.4.1.4874.2.2.29.1.17.1.10	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
STR juniBgpAggregateSuppressMap	1.3.6.1.4.1.4874.2.2.29.1.17.1.11	DisplayString	read-create	The suppress route-map name. If a suppress route-map has been specified, all routes which are covered by the aggregate and which match the suppress route-map are suppressed. An empty string means no inbound route-map.
BIT juniBgpAggregateUnconfiguredAttributes	1.3.6.1.4.1.4874.2.2.29.1.17.1.12	Bits	read-create	On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
juniBgpVrfTable	1.3.6.1.4.1.4874.2.2.29.1.18		not-accessible	The Juniper BGP VRF Table describes the BGP-specific characteristics of a VPN routing forwarding instance.
juniBgpVrfEntry	1.3.6.1.4.1.4874.2.2.29.1.18.1		not-accessible	The BGP VRF Entry describes BGP-specific characteristics of one VRF.
JUN juniBgpVrfName	1.3.6.1.4.1.4874.2.2.29.1.18.1.1	JuniVrfName	not-accessible	The name of the VPN Routing Forwarding (VRF) instance.
T/F juniBgpVrfSynchronization	1.3.6.1.4.1.4874.2.2.29.1.18.1.2	TruthValue	read-create	Set this object to true(1) in order to have IGP route synchronization enabled.
T/F juniBgpVrfAutoSummary	1.3.6.1.4.1.4874.2.2.29.1.18.1.3	TruthValue	read-create	Set this object to true(1) in order to automatically summarize redistributed routes to their natural network mask.
I32 juniBgpVrfExternalDistance	1.3.6.1.4.1.4874.2.2.29.1.18.1.4	Integer32	read-create	Obsolete administrative distance for external routes. Replaced by juniBgpAddressFamilyExternalDistance.
I32 juniBgpVrfInternalDistance	1.3.6.1.4.1.4874.2.2.29.1.18.1.5	Integer32	read-create	Obsolete administrative distance for internal routes. Replaced by juniBgpAddressFamilyInternalDistance.
I32 juniBgpVrfLocalDistance	1.3.6.1.4.1.4874.2.2.29.1.18.1.6	Integer32	read-create	Obsolete administrative distance for local routes. Replaced by juniBgpAddressFamilyLocalDistance.
JUN juniBgpVrfResetConnectionType	1.3.6.1.4.1.4874.2.2.29.1.18.1.7	JuniBgpResetConnectionType	read-create	Writing a value to this object causes the sessions to all peers in this VRF to be cleared; the value determines what type of clear is executed (hard clear, soft clear in, soft clear out, etc.). Reading this object has no effect and always returns resetTypeNoop.
ROW juniBgpVrfRowStatus	1.3.6.1.4.1.4874.2.2.29.1.18.1.8	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
INT juniBgpVrfOperationalState	1.3.6.1.4.1.4874.2.2.29.1.18.1.9	INTEGER	read-only	The BGP VRF operational state.
T/F juniBgpVrfAddUnicastRoutesToMulticastView	1.3.6.1.4.1.4874.2.2.29.1.18.1.10	TruthValue	read-create	Set this object to true(1) in order to add routes learnt by IPv4 Unicast BGP to the multicast route table.
I32 juniBgpVrfMaximumPathsEbgp	1.3.6.1.4.1.4874.2.2.29.1.18.1.11	Integer32	read-create	The maximum number of routes received from EBGP peers which BGP can select as equal cost. Zero means that routes from EBGP peers cannot be selected as equal cost.
I32 juniBgpVrfMaximumPathsIbgp	1.3.6.1.4.1.4874.2.2.29.1.18.1.12	Integer32	read-create	The maximum number of routes received from IBGP peers which BGP can select as equal cost. Zero means that routes from IBGP peers cannot be selected as equal cost.
BIT juniBgpVrfUnconfiguredAttributes	1.3.6.1.4.1.4874.2.2.29.1.18.1.13	Bits	read-create	On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
I32 juniBgpVrfMaximumPathsEIbgp	1.3.6.1.4.1.4874.2.2.29.1.18.1.14	Integer32	read-create	The maximum number of routes received from both EBGP and IBGP peers which BGP can select as equal cost. Zero means that routes from both EBGP and IBGP peers cannot be selected as equal cost.
T/F juniBgpVrfCarriersCarrierModeEnabled	1.3.6.1.4.1.4874.2.2.29.1.18.1.16	TruthValue	read-only	Obsolete the BGP carrier's carrier flag since there is no need for it when in carrier's carrier mode.
juniBgpAddressFamilyTable	1.3.6.1.4.1.4874.2.2.29.1.19		not-accessible	The BGP AddressFamily Entry describes BGP-specific characteristics of one AddressFamily.
juniBgpAddressFamilyEntry	1.3.6.1.4.1.4874.2.2.29.1.19.1		not-accessible	The BGP address family entry
JUN juniBgpAddressFamilyVrfName	1.3.6.1.4.1.4874.2.2.29.1.19.1.1	JuniVrfName	not-accessible	The name of the VPN Routing Forwarding (VRF) instance in which this address-family is configured. The empty string indicates that this address-family is not in a VRF.
JUN juniBgpAddressFamilyAfi	1.3.6.1.4.1.4874.2.2.29.1.19.1.2	JuniBgpAfi	not-accessible	The AFI of the address-family.
JUN juniBgpAddressFamilySafi	1.3.6.1.4.1.4874.2.2.29.1.19.1.3	JuniBgpSafi	not-accessible	The SAFI of the address-family.
T/F juniBgpAddressFamilyDefaultOriginate	1.3.6.1.4.1.4874.2.2.29.1.19.1.4	TruthValue	read-create	Set this object to true(1) in order to advertise a default route, if present.
T/F juniBgpAddressFamilyRouteFlapDampening	1.3.6.1.4.1.4874.2.2.29.1.19.1.5	TruthValue	read-create	Set this object to true(1) in order to enable route flap dampening.
U32 juniBgpAddressFamilyDampeningSuppressThreshold	1.3.6.1.4.1.4874.2.2.29.1.19.1.6	Unsigned32	read-create	The dampening cutoff threshold (scaled).
U32 juniBgpAddressFamilyDampeningReuseThreshold	1.3.6.1.4.1.4874.2.2.29.1.19.1.7	Unsigned32	read-create	The dampening reuse threshold (scaled).
U32 juniBgpAddressFamilyDampeningMaxHoldDownTime	1.3.6.1.4.1.4874.2.2.29.1.19.1.8	Unsigned32	read-create	Maximum route holddown time, in seconds.
U32 juniBgpAddressFamilyDampeningHalfLifeReachable	1.3.6.1.4.1.4874.2.2.29.1.19.1.9	Unsigned32	read-create	Figure of merit half life for reachable routes, in seconds.
U32 juniBgpAddressFamilyDampeningHalfLifeUnreachable	1.3.6.1.4.1.4874.2.2.29.1.19.1.10	Unsigned32	read-create	Figure of merit half life for unreachable routes, in seconds.
STR juniBgpAddressFamilyDampeningRouteMapName	1.3.6.1.4.1.4874.2.2.29.1.19.1.11	DisplayString	read-create	The name of the route-map used to determine which routes are dampened and which aren't and to set the dampening parameters for those routes which are dampenend. A zero length route-map name means don't use a route-map for this.
JUN juniBgpAddressFamilyResetConnectionType	1.3.6.1.4.1.4874.2.2.29.1.19.1.12	JuniBgpResetConnectionType	read-create	Writing a value to this object causes one individual address family within the sessions to all peers in this VRF to be cleared; the value determines what type of clear is executed (hard clear, soft clear in, soft clear out, etc.). Note that hard clearing an address family within a session will bounce the session and thus also affect the other address families in the session. Reading this object has no effect and always returns resetTypeNoop.
ROW juniBgpAddressFamilyRowStatus	1.3.6.1.4.1.4874.2.2.29.1.19.1.13	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
INT juniBgpAddressFamilyOperationalState	1.3.6.1.4.1.4874.2.2.29.1.19.1.14	INTEGER	read-only	The BGP address family operational state.
BIT juniBgpAddressFamilyUnconfiguredAttributes	1.3.6.1.4.1.4874.2.2.29.1.19.1.15	Bits	read-create	On get each bit indicates whether the corresponding attribute is configured or unconfigured: 0 = The attribute is configured (i.e. the configured value is the operational value). 1 = The attribute is unconfigured (i.e. the operational value is inherited from the a higher level which could be the default value). Getting the attribute value itself always returns the operational value of that attribute regardless of whether the attribute is configured or unconfigured. On write each bit indicates whether or not the corresponding attribute should be set to the unconfigured state: 0 = No operation (i.e. do not change the state of the attribute). 1 = Set the attribute to the unconfigured state. Setting an attribute to a value has the automatic side-effect of setting the bit with the same name to zero.
I32 juniBgpAddressFamilyExternalDistance	1.3.6.1.4.1.4874.2.2.29.1.19.1.16	Integer32	read-create	The administrative distance for external routes.
I32 juniBgpAddressFamilyInternalDistance	1.3.6.1.4.1.4874.2.2.29.1.19.1.17	Integer32	read-create	The administrative distance for internal routes.
I32 juniBgpAddressFamilyLocalDistance	1.3.6.1.4.1.4874.2.2.29.1.19.1.18	Integer32	read-create	The administrative distance for local routes.
STR juniBgpAddressFamilyDefaultOriginateRouteMap	1.3.6.1.4.1.4874.2.2.29.1.19.1.19	DisplayString	read-create	The route-map to apply to the default route which is advertised as a result of setting juniBgpAddressFamilyDefaultOriginate to true. An empty string means that no route-map is applied.
STR juniBgpAddressFamilyIpIntfProfileNameForMplsHeads	1.3.6.1.4.1.4874.2.2.29.1.19.1.20	DisplayString	read-create	Obsolete the name of the IP interface profile used by BGP to create IP dynamic interfaces on top of MPLS stacked tunnel heads. When support for BGP-created IP dynamic interfaces was removed, BGP profile names were obsoleted too.
STR juniBgpAddressFamilyIpIntfProfileNameForMplsTails	1.3.6.1.4.1.4874.2.2.29.1.19.1.21	DisplayString	read-create	Obsolete the name of the IP interface profile used by BGP to create IP dynamic interfaces on top of MPLS stacked tunnel tails. When support for BGP-created IP dynamic interfaces was removed, BGP profile names were obsoleted too.
STR juniBgpAddressFamilyIpIntfServiceProfileNameForMplsHeads	1.3.6.1.4.1.4874.2.2.29.1.19.1.22	DisplayString	read-create	Obsolete the name of the IP interface service-profile used by BGP to create IP dynamic interfaces on top of MPLS stacked tunnel heads. When support for BGP-created dynamic interfaces was removed, BGP profile names were obsoleted too.
STR juniBgpAddressFamilyIpIntfServiceProfileNameForMplsTails	1.3.6.1.4.1.4874.2.2.29.1.19.1.23	DisplayString	read-create	The name of the IP interface service-profile used by BGP to create IP dynamic interfaces on top of MPLS stacked tunnel tails. When support for BGP-created dynamic interfaces was removed, BGP profile names were obsoleted too.
T/F juniBgpAddressFamilyCheckVpnNextHops	1.3.6.1.4.1.4874.2.2.29.1.19.1.24	TruthValue	read-create	If this object is set to true, the reachability of the next-hops of routes in this address-family are checked. If this object is set to false, the next-hops if routes in this address-families are always considered to be reachable. This attribute only applies to address- families with SAFI 128 (labeled-vpn-unicast). For all other address- families this attributes is meaningless and attempting to set the attribute will result in an error.
T/F juniBgpAddressFamilyPathSelectionIsDeferred	1.3.6.1.4.1.4874.2.2.29.1.19.1.25	TruthValue	read-only	Is path selection for the address-family currently deferred?
T/F juniBgpAddressFamilyPreventBgpRoutesFromBeingPushedToLineCards	1.3.6.1.4.1.4874.2.2.29.1.19.1.26	TruthValue	read-only	Is BGP still in the process of placing fresh routes in the route table after a restart? During this period the line cards are forced to continue forwarding using the old stale routes.
I32 juniBgpAddressFamilyTimeUntilPathSelectionDeferTimerExpires	1.3.6.1.4.1.4874.2.2.29.1.19.1.27	Integer32	read-only	The number of seconds until the path selection defer timer expires or zero if it is not running.
juniBgpStorageGroup	1.3.6.1.4.1.4874.2.2.29.1.20
NUM juniBgpStorageInitialHeapSize	1.3.6.1.4.1.4874.2.2.29.1.20.1	JuniBgpStorageInteger	read-write	Obsolete initial size of the BGP heap in octets. The BGP heap is used for a small number of variable sized data structures.
NUM juniBgpStorageMaxHeapSize	1.3.6.1.4.1.4874.2.2.29.1.20.2	JuniBgpStorageInteger	read-write	Obsolete maximum size of the BGP heap in octets.
NUM juniBgpStorageInitialVrfPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.4	JuniBgpStorageInteger	read-write	Obsolete initial size of the VRF pool in entries. One entry is allocated from the VRF pool for each VRF used by BGP.
NUM juniBgpStorageMaxVrfPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.5	JuniBgpStorageInteger	read-write	Obsolete maximum size of the VRF pool in entries.
NUM juniBgpStorageInitialAddressFamilyPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.6	JuniBgpStorageInteger	read-write	Obsolete initial size of the address-family pool in entries. One entry is allocated from the address-family pool for each address-family used by BGP.
NUM juniBgpStorageMaxAddressFamilyPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.7	JuniBgpStorageInteger	read-write	Obsolete initial size of the address-family pool in entries.
NUM juniBgpStorageInitialPeerPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.8	JuniBgpStorageInteger	read-write	Obsolete initial size of the peer pool in entries. One entry is allocated from the peer pool for each peer configured in BGP.
NUM juniBgpStorageMaxPeerPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.9	JuniBgpStorageInteger	read-write	Obsolete maximum size of the peer pool in entries.
NUM juniBgpStorageInitialPeerAfPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.10	JuniBgpStorageInteger	read-write	Obsolete initial size of the peer-address-family pool in entries. One entry is allocated from the peer-address-family pool for each address family activated for any peer in BGP (including the IPv4 unicast address families which are usually activated by default for each peer).
NUM juniBgpStorageMaxPeerAfPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.11	JuniBgpStorageInteger	read-write	Obsolete maximum size of the peer-address-family pool in entries.
NUM juniBgpStorageInitialPeerGroupPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.12	JuniBgpStorageInteger	read-write	Obsolete initial size of the peer-group pool in entries. One entry is allocated from the peer-group pool for each peer-group configured in BGP.
NUM juniBgpStorageMaxPeerGroupPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.13	JuniBgpStorageInteger	read-write	Obsolete maximum size of the peer-group pool in entries.
NUM juniBgpStorageInitialPeerGroupAfPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.14	JuniBgpStorageInteger	read-write	Obsolete initial size of the peer-group-address-family pool in entries. One entry is allocated from the peer-group-address-family pool for each address family activated for any peer-group in BGP (including the IPv4 unicast address families which are usually activated by default for each peer-group).
NUM juniBgpStorageMaxPeerGroupAfPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.15	JuniBgpStorageInteger	read-write	Obsolete maximum size of the peer-group-address-family pool in entries.
NUM juniBgpStorageInitialNetworkPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.16	JuniBgpStorageInteger	read-write	Obsolete initial size of the network pool in entries. One entry is allocated from the network pool for each network configured in BGP.
NUM juniBgpStorageMaxNetworkPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.17	JuniBgpStorageInteger	read-write	Obsolete maximum size of the network pool in entries.
NUM juniBgpStorageInitialAggregatePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.18	JuniBgpStorageInteger	read-write	Obsolete initial size of the aggregate pool in entries. One entry is allocated from the aggregate pool for each aggregate configured in BGP.
NUM juniBgpStorageMaxAggregatePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.19	JuniBgpStorageInteger	read-write	Obsolete maximum size of the aggregate pool in entries.
NUM juniBgpStorageInitialDestinationPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.20	JuniBgpStorageInteger	read-write	Obsolete initial size of the destination pool in entries. One entry is allocated from the destination pool for each unique prefix in the BGP RIB.
NUM juniBgpStorageMaxDestinationPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.21	JuniBgpStorageInteger	read-write	Obsolete maximum size of the destination pool in entries.
NUM juniBgpStorageInitialRoutePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.22	JuniBgpStorageInteger	read-write	Obsolete initial size of the route pool in entries. One entry is allocated from the route pool for each received non-VPN route in the BGP RIB.
NUM juniBgpStorageMaxRoutePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.23	JuniBgpStorageInteger	read-write	Obsolete maximum size of the route pool in entries.
NUM juniBgpStorageInitialAttributesPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.24	JuniBgpStorageInteger	read-write	Obsolete initial size of the attributes pool in entries. One entry is allocated from the attributes pool for each unique combination of path attributes of routes in the BGP RIB.
NUM juniBgpStorageMaxAttributesPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.25	JuniBgpStorageInteger	read-write	Obsolete maximum size of the attributes pool in entries.
NUM juniBgpStorageInitialRouteFlapHistoryPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.26	JuniBgpStorageInteger	read-write	Obsolete initial size of the route-flap-history pool in entries. One entry is allocated from the route-flap-history pool for each route in the BGP RIB which has route-flap dampening history associated with it.
NUM juniBgpStorageMaxRouteFlapHistoryPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.27	JuniBgpStorageInteger	read-write	Obsolete maximum size of the route-flap-history pool in entries.
NUM juniBgpStorageInitialNetworkRoutePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.28	JuniBgpStorageInteger	read-write	Obsolete initial size of the network-route pool in entries. One entry is allocated from the network-route pool for each network route in the BGP RIB.
NUM juniBgpStorageMaxNetworkRoutePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.29	JuniBgpStorageInteger	read-write	Obsolete maximum size of the network-route pool in entries.
NUM juniBgpStorageInitialRedistributedRoutePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.30	JuniBgpStorageInteger	read-write	Obsolete initial size of the redistributed-route pool in entries. One entry is allocated from the redistributed-route pool for each redistributed route in the BGP RIB.
NUM juniBgpStorageMaxRedistributedRoutePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.31	JuniBgpStorageInteger	read-write	Obsolete maximum size of the redistributed-route pool in entries.
NUM juniBgpStorageInitialAggregateRoutePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.32	JuniBgpStorageInteger	read-write	Obsolete initial size of the aggregate-route pool in entries. One entry is allocated from the aggregate-route pool for each aggregate route in the BGP RIB.
NUM juniBgpStorageMaxAggregateRoutePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.33	JuniBgpStorageInteger	read-write	Obsolete maximum size of the aggregate-route pool in entries.
NUM juniBgpStorageInitialAutoSummaryRoutePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.34	JuniBgpStorageInteger	read-write	Obsolete initial size of the auto-summary-route pool in entries. One entry is allocated from the auto-summary-route pool for each auto-summary route in the BGP RIB.
NUM juniBgpStorageMaxAutoSummaryRoutePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.35	JuniBgpStorageInteger	read-write	Obsolete maximum size of the auto-summary-route pool in entries.
NUM juniBgpStorageInitialHistoryRoutePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.36	JuniBgpStorageInteger	read-write	Obsolete object is obsolete. Setting it has not effect and reading this object returns an undefined value.
NUM juniBgpStorageMaxHistoryRoutePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.37	JuniBgpStorageInteger	read-write	Obsolete object is obsolete. Setting it has not effect and reading this object returns an undefined value.
NUM juniBgpStorageInitialSendQueueEntryPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.38	JuniBgpStorageInteger	read-write	Obsolete initial size of the send-queue-entry pool in entries. One entry is allocated from the send-queue-entry pool for update messages which is queued for transmission to a peer.
NUM juniBgpStorageMaxSendQueueEntryPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.39	JuniBgpStorageInteger	read-write	Obsolete maximum size of the send-queue-entry pool in entries.
NUM juniBgpStorageInitialVpnRoutePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.40	JuniBgpStorageInteger	read-write	Obsolete initial size of the vpn-route pool in entries. One entry is allocated from the vpn-route pool for each received VPN route in the BGP RIB.
NUM juniBgpStorageMaxVpnRoutePoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.41	JuniBgpStorageInteger	read-write	Obsolete maximum size of the vpn-route pool in entries.
NUM juniBgpStorageInitialRouteTargetPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.42	JuniBgpStorageInteger	read-write	Obsolete initial size of the route-target pool in entries. One entry is allocated from the route-target pool for each route-target imported in any VRF used by BGP.
NUM juniBgpStorageMaxRouteTargetPoolSize	1.3.6.1.4.1.4874.2.2.29.1.20.43	JuniBgpStorageInteger	read-write	Obsolete maximum size of the route-target pool in entries.
juniBgpRouteExtendedCommunityTable	1.3.6.1.4.1.4874.2.2.29.1.22		not-accessible	The obsolete BGP-4 Path Extended Community Table contained information about communities within destination networks received from all BGP4 peers. This table has been replaced by the juniBgpNewRouteExtendedCommunityTable.
juniBgpRouteExtendedCommunityEntry	1.3.6.1.4.1.4874.2.2.29.1.22.1		not-accessible	Extended Community attribute information within a path to a network.
OCT juniBgpRouteExtendedCommunityNumber	1.3.6.1.4.1.4874.2.2.29.1.22.1.1	OCTET STRING	read-only	The extended community number.
juniBgpNewRouteTable	1.3.6.1.4.1.4874.2.2.29.1.23		not-accessible	The BGP-4 Received Path Attribute Table contains additional information about paths to destination networks received from all BGP4 peers.
juniBgpNewRouteEntry	1.3.6.1.4.1.4874.2.2.29.1.23.1		not-accessible	Additional information about a path to a network.
JUN juniBgpNewRouteVrfName	1.3.6.1.4.1.4874.2.2.29.1.23.1.1	JuniVrfName	not-accessible	The name of the VPN Routing Forwarding (VRF) instance in which this route is present. The empty string indicates that this route is not in a VRF.
JUN juniBgpNewRouteAfi	1.3.6.1.4.1.4874.2.2.29.1.23.1.2	JuniBgpAfi	not-accessible	The AFI of the address-family in which this route is present.
JUN juniBgpNewRouteSafi	1.3.6.1.4.1.4874.2.2.29.1.23.1.3	JuniBgpSafi	not-accessible	The SAFI of the address-family in which this route is present.
IP juniBgpNewRouteIpAddrPrefix	1.3.6.1.4.1.4874.2.2.29.1.23.1.4	IpAddress	not-accessible	The IP address prefix of the route. This object is an IP address containing the prefix with length specified by juniBgpNewRouteIpAddrPrefixLen. Any bits beyond the length specified by juniBgpNewRouteIpAddrPrefixLen are zeroed.
I32 juniBgpNewRouteIpAddrPrefixLen	1.3.6.1.4.1.4874.2.2.29.1.23.1.5	Integer32	not-accessible	Length in bits of the IP address prefix of the route.
OCT juniBgpNewRouteDistinguisher	1.3.6.1.4.1.4874.2.2.29.1.23.1.6	OCTET STRING	not-accessible	The Route Distinguisher (RD) of the route. This object has an undefined value for non-VPN routes.
IP juniBgpNewRoutePeer	1.3.6.1.4.1.4874.2.2.29.1.23.1.7	IpAddress	not-accessible	The IP address of the peer from which the route was received. This object has value 0.0.0.0 is the route was a locally originated route.
INT juniBgpNewRouteRouteType	1.3.6.1.4.1.4874.2.2.29.1.23.1.8	INTEGER	not-accessible	The type of the route.
OCT juniBgpNewRouteOriginalRd	1.3.6.1.4.1.4874.2.2.29.1.23.1.9	OCTET STRING	not-accessible	The original Route Distinguisher (RD) of a VPN route. For VPN routes which are originated in a VRF or which are received from a CE the original RD is equal to the RD of the VRF. For VPN routes which are received from another PE and imported into a VRF, the original RD is the RD which was received from the other PE (the RD of the route itself is changed to the RD for the VRF when the route is imported into the VRF). For non-VPN routes the value of this object is undefined.
IP juniBgpNewRouteOriginatorId	1.3.6.1.4.1.4874.2.2.29.1.23.1.10	IpAddress	read-only	The Originator-ID path attribute of the route if present. The juniBgpNewRouteOriginatorIdPresent object indicates whether the Originator-ID path attribute is present.
T/F juniBgpNewRouteAtomicAggregatePresent	1.3.6.1.4.1.4874.2.2.29.1.23.1.11	TruthValue	read-only	Atomic-Aggregate path attribute is present.
T/F juniBgpNewRouteMedPresent	1.3.6.1.4.1.4874.2.2.29.1.23.1.12	TruthValue	read-only	The Multi-Exit-Discriminator path attribute is present.
T/F juniBgpNewRouteLocalPrefPresent	1.3.6.1.4.1.4874.2.2.29.1.23.1.13	TruthValue	read-only	The Local-Pref path attribute is present.
T/F juniBgpNewRouteAggregatorPresent	1.3.6.1.4.1.4874.2.2.29.1.23.1.14	TruthValue	read-only	The Aggregator path attribute is present.
T/F juniBgpNewRouteCommunitiesPresent	1.3.6.1.4.1.4874.2.2.29.1.23.1.15	TruthValue	read-only	The Communities path attribute is present.
T/F juniBgpNewRouteOriginatorIdPresent	1.3.6.1.4.1.4874.2.2.29.1.23.1.16	TruthValue	read-only	The Originator-ID path attribute is present.
T/F juniBgpNewRouteClusterListPresent	1.3.6.1.4.1.4874.2.2.29.1.23.1.17	TruthValue	read-only	The Cluster-List path attribute is present.
U32 juniBgpNewRouteWeight	1.3.6.1.4.1.4874.2.2.29.1.23.1.18	Unsigned32	read-only	The weight of the route.
INT juniBgpNewRouteOrigin	1.3.6.1.4.1.4874.2.2.29.1.23.1.19	INTEGER	read-only	The value of the Origin path attribute.
OCT juniBgpNewRouteASPathSegment	1.3.6.1.4.1.4874.2.2.29.1.23.1.20	OCTET STRING	read-only	The value of the AS-path path attribute (as encoded in the received update message).
IP juniBgpNewRouteNextHop	1.3.6.1.4.1.4874.2.2.29.1.23.1.21	IpAddress	read-only	The value of the Next-Hop path attribute.
U32 juniBgpNewRouteMultiExitDisc	1.3.6.1.4.1.4874.2.2.29.1.23.1.22	Unsigned32	read-only	The value of the Multi-Exit-Discriminator path attribute if present. The juniBgpNewRouteMedPresent object indicates whether the Multi-Exit-Discriminator path attribute is present.
U32 juniBgpNewRouteLocalPref	1.3.6.1.4.1.4874.2.2.29.1.23.1.23	Unsigned32	read-only	The value of the Local-Pref path attribute if present. The juniBgpNewRouteLocalPrefPresent object indicates whether the Local-Pref path attribute is present.
INT juniBgpNewRouteAtomicAggregate	1.3.6.1.4.1.4874.2.2.29.1.23.1.24	INTEGER	read-only	Whether or not the local system has selected a less specific route without selecting a more specific route.
I32 juniBgpNewRouteAggregatorAS	1.3.6.1.4.1.4874.2.2.29.1.23.1.25	Integer32	read-only	The value of the AS field in the Aggregator path attribute if present. The juniBgpNewRouteAggregatorPresent object indicates whether the Aggregator path attribute is present.
IP juniBgpNewRouteAggregatorAddress	1.3.6.1.4.1.4874.2.2.29.1.23.1.26	IpAddress	read-only	The value of the address field in the Aggregator path attribute if present. The juniBgpNewRouteAggregatorPresent object indicates whether the Aggregator path attribute is present.
T/F juniBgpNewRouteBestInIpRouteTable	1.3.6.1.4.1.4874.2.2.29.1.23.1.27	TruthValue	read-only	When BGP places a routes in the IP route table, that route may not be used for forwarding traffic if there are other routes (e.g. IGP routes or static routes) to that same prefix with a better administrative distance in the IP route table. This object indicates whether or not the BGP route in the IP route table is the best route (and hence is used for forwarding traffic).
OCT juniBgpNewRouteUnknown	1.3.6.1.4.1.4874.2.2.29.1.23.1.28	OCTET STRING	read-only	One or more path attributes not understood by this BGP4 speaker. Size zero (0) indicates the absence of such attribute(s). Octets beyond the maximum size, if any, are not recorded by this object.
T/F juniBgpNewRouteExtendedCommunitiesPresent	1.3.6.1.4.1.4874.2.2.29.1.23.1.29	TruthValue	read-only	Is the Extended-Communities path attribute present?
T/F juniBgpNewRouteValid	1.3.6.1.4.1.4874.2.2.29.1.23.1.30	TruthValue	read-only	Is the route valid? The route is declared invalid if there is something wrong with it which is not serious enough for sending a notification, but it serious enough for not placing it in the IP route table or propagating it to other peers (for example the next-hop of the route is a local address).
INT juniBgpNewRouteSuppressedBy	1.3.6.1.4.1.4874.2.2.29.1.23.1.31	INTEGER	read-only	Indicates whether or not the route is suppressed, and if so why: suppressedByNothing - Route is not suppressed. suppressedByAggregate - Route is suppressed by a summary-only aggregate. suppressedByAutoSummary - Route is suppressed by an auto-summary. suppressedByDampening - Route is suppressed as a result of route-flap dampening.
T/F juniBgpNewRouteNextHopReachable	1.3.6.1.4.1.4874.2.2.29.1.23.1.32	TruthValue	read-only	Is the indirect next-hop of the route reachable (i.e. can the indirect next-hop of the route be resolved to at least one direct next-hop)?
T/F juniBgpNewRouteSynchronizedWithIgp	1.3.6.1.4.1.4874.2.2.29.1.23.1.33	TruthValue	read-only	Is the route is synchronized (i.e. is there is an IGP route to the same prefix in the IP route table)?
T/F juniBgpNewRoutePlaceInIpRouteTable	1.3.6.1.4.1.4874.2.2.29.1.23.1.34	TruthValue	read-only	Has a BGP route for this prefix been placed in the IP route table?
T/F juniBgpNewRouteAdvertiseToExternalPeers	1.3.6.1.4.1.4874.2.2.29.1.23.1.35	TruthValue	read-only	Should this route be advertised to external peers?
T/F juniBgpNewRouteAdvertiseToInternalPeers	1.3.6.1.4.1.4874.2.2.29.1.23.1.36	TruthValue	read-only	Should this route be advertised to internal peers?
U32 juniBgpNewRouteMplsLabel	1.3.6.1.4.1.4874.2.2.29.1.23.1.37	Unsigned32	read-only	The obsolete MPLS label for the route. This object was obsoleted when in-label and out-label were introduced.
U32 juniBgpNewRouteNextHopMetric	1.3.6.1.4.1.4874.2.2.29.1.23.1.38	Unsigned32	read-only	The metric of direct next-hop of this BGP route.
U32 juniBgpNewRouteMplsInLabel	1.3.6.1.4.1.4874.2.2.29.1.23.1.39	Unsigned32	read-only	The MPLS in-label for the route. This is the label that MPLS frames are going to be received with.
U32 juniBgpNewRouteMplsOutLabel	1.3.6.1.4.1.4874.2.2.29.1.23.1.40	Unsigned32	read-only	The MPLS out-label for the route. This is the label that MPLS frames are going to be sent with.
T/F juniBgpNewRouteLeaked	1.3.6.1.4.1.4874.2.2.29.1.23.1.41	TruthValue	read-only	Is the route leaked into this address-family from another address- family?
T/F juniBgpNewRouteStale	1.3.6.1.4.1.4874.2.2.29.1.23.1.42	TruthValue	read-only	Is the route stale?
juniBgpNewRouteFlapHistoryTable	1.3.6.1.4.1.4874.2.2.29.1.24		not-accessible	The BGP Route Flap History Table contains information about recorded route flap events.
juniBgpNewRouteFlapHistoryEntry	1.3.6.1.4.1.4874.2.2.29.1.24.1		not-accessible	An instance in the list of route flap events.
INT juniBgpNewRouteFlapState	1.3.6.1.4.1.4874.2.2.29.1.24.1.1	INTEGER	read-only	Current state: stateAvailable(1) - indicates path is available stateSuppressedReachable(2) - indicates path is suppressed, destination is reachable stateSuppressedUnreachable(3) - indicates path in suppressed, destination is not reachable
U32 juniBgpNewRouteFlapFigureOfMerit	1.3.6.1.4.1.4874.2.2.29.1.24.1.2	Unsigned32	read-only	Calculated figure-of-merit.
U32 juniBgpNewRouteFlapRemainingTime	1.3.6.1.4.1.4874.2.2.29.1.24.1.3	Unsigned32	read-only	Number of seconds until reuse or removal.
U32 juniBgpNewRouteFlapSuppressThreshold	1.3.6.1.4.1.4874.2.2.29.1.24.1.4	Unsigned32	read-only	Damping cutoff threshold (scaled).
U32 juniBgpNewRouteFlapReuseThreshold	1.3.6.1.4.1.4874.2.2.29.1.24.1.5	Unsigned32	read-only	Damping reuse threshold (scaled).
U32 juniBgpNewRouteFlapMaxHoldDownTime	1.3.6.1.4.1.4874.2.2.29.1.24.1.6	Unsigned32	read-only	Maximum route holddown time (seconds).
U32 juniBgpNewRouteFlapHalfLifeReachable	1.3.6.1.4.1.4874.2.2.29.1.24.1.7	Unsigned32	read-only	Figure of merit half life for reachable routes (seconds).
U32 juniBgpNewRouteFlapHalfLifeUnreachable	1.3.6.1.4.1.4874.2.2.29.1.24.1.8	Unsigned32	read-only	Figure of merit half life for unreachable routes (seconds).
juniBgpNewRouteCommunityTable	1.3.6.1.4.1.4874.2.2.29.1.25		not-accessible	The BGP-4 Path Community Table contains information about communities within destination networks received from all BGP4 peers.
juniBgpNewRouteCommunityEntry	1.3.6.1.4.1.4874.2.2.29.1.25.1		not-accessible	Community attribute information within a path to a network.
U32 juniBgpNewRouteCommunityNumber	1.3.6.1.4.1.4874.2.2.29.1.25.1.1	Unsigned32	read-only	The community number.
juniBgpNewRouteExtendedCommunityTable	1.3.6.1.4.1.4874.2.2.29.1.26		not-accessible	The BGP-4 Path Extended Community Table contains information about communities within destination networks received from all BGP4 peers.
juniBgpNewRouteExtendedCommunityEntry	1.3.6.1.4.1.4874.2.2.29.1.26.1		not-accessible	Extended Community attribute information within a path to a network.
OCT juniBgpNewRouteExtendedCommunityNumber	1.3.6.1.4.1.4874.2.2.29.1.26.1.1	OCTET STRING	read-only	The extended community number.
juniBgpNewRouteClusterIdTable	1.3.6.1.4.1.4874.2.2.29.1.27		not-accessible	The BGP-4 Path ClusterId Table contains information about router reflector cluster IDs.
juniBgpNewRouteClusterIdEntry	1.3.6.1.4.1.4874.2.2.29.1.27.1		not-accessible	ClusterId attribute information within a path to a network.
U32 juniBgpNewRouteClusterId	1.3.6.1.4.1.4874.2.2.29.1.27.1.1	Unsigned32	read-only	The cluster ID.
juniBgpFourOctetConfederationPeerTable	1.3.6.1.4.1.4874.2.2.29.1.28		not-accessible	The BGP New Confederation Peer Table describes the BGP-specific characteristics of confederation peers using four-octet AS-numbers.
juniBgpFourOctetConfederationPeerEntry	1.3.6.1.4.1.4874.2.2.29.1.28.1		not-accessible	The BGP New Confederation Peer Entry describes BGP-specific characteristics of one confederation peer using four-octet AS-numbers.
JUN juniBgpFourOctetConfederationPeerAsNumber	1.3.6.1.4.1.4874.2.2.29.1.28.1.1	JuniBgpFourOctetAsNumber	not-accessible	The four-octet AS-number of this confederation peer.
ROW juniBgpFourOctetConfederationPeerRowStatus	1.3.6.1.4.1.4874.2.2.29.1.28.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy
juniBgpPeerDynamicCapabilityTable	1.3.6.1.4.1.4874.2.2.29.1.29		not-accessible	The BGP PeerDynamicCapbility Table describes which dynamic capbilities we proposed to the peer, which the peer proposed to us, and which are being used.
juniBgpPeerDynamicCapabilityEntry	1.3.6.1.4.1.4874.2.2.29.1.29.1		not-accessible	The BGP PeerDynamicCapbility Entry describes one dynamic capability.
JUN juniBgpPeerDynamicCapabilityPeerVrfName	1.3.6.1.4.1.4874.2.2.29.1.29.1.1	JuniVrfName	not-accessible	The name of the VPN Routing Forwarding (VRF) instance in which this peer is configured. The empty string indicates that this peer is not in a VRF.
IP juniBgpPeerDynamicCapabilityPeerRemoteAddr	1.3.6.1.4.1.4874.2.2.29.1.29.1.2	IpAddress	not-accessible	The remote IP address of this entry's BGP peer.
I32 juniBgpPeerDynamicCapabilityCode	1.3.6.1.4.1.4874.2.2.29.1.29.1.3	Integer32	not-accessible	The capability code for the dynamic capability.
T/F juniBgpPeerDynamicCapabilitySent	1.3.6.1.4.1.4874.2.2.29.1.29.1.4	TruthValue	read-only	Returns true if we advertised capability code juniBgpPeerDynamicCapabilityCode in the dynamic-capability-negotiation capability which we sent to this peer.
T/F juniBgpPeerDynamicCapabilityReceived	1.3.6.1.4.1.4874.2.2.29.1.29.1.5	TruthValue	read-only	Returns true if the peer advertised capability code juniBgpPeerDynamicCapabilityCode in the dynamic-capability-negotiation capability which this peer sent to us.
juniBgpPeerAddressFamilyConditionalAdvTable	1.3.6.1.4.1.4874.2.2.29.1.30		not-accessible	The Juniper BGP Peer Address Family Conditional Advertisement Table describes the BGP conditional advertisement attributes in an Address Family for a peer.
juniBgpPeerAddressFamilyConditionalAdvEntry	1.3.6.1.4.1.4874.2.2.29.1.30.1		not-accessible	The Juniper BGP Peer Address Family Conditional Advertisement Entry describes a specific conditional advertisement entry in Address Family for a peer.
JUN juniBgpPeerAddressFamilyConditionalAdvAdvertiseMap	1.3.6.1.4.1.4874.2.2.29.1.30.1.1	JuniBgpAdvertiseMapName	not-accessible	The route-map for conditional advertisement.
STR juniBgpPeerAddressFamilyConditionalAdvConditionMap	1.3.6.1.4.1.4874.2.2.29.1.30.1.2	DisplayString	read-create	The condition-map to apply for this conditional advertisement entry.
T/F juniBgpPeerAddressFamilyConditionalAdvIsExistMap	1.3.6.1.4.1.4874.2.2.29.1.30.1.3	TruthValue	read-create	Set this value to true(1) if the condition-map specified should be applied as an exist-map. If the condition-map should be applied as a non-exist-map, set it to false(2).
I32 juniBgpPeerAddressFamilyConditionalAdvSequenceNum	1.3.6.1.4.1.4874.2.2.29.1.30.1.4	Integer32	read-create	The sequence number of this conditional advertisement entry.
JUN juniBgpPeerAddressFamilyConditionalAdvStatus	1.3.6.1.4.1.4874.2.2.29.1.30.1.5	JuniBgpConditionalAdvStatus	read-only	This value will be advertise(1) if the status of this advertise-map is evaluated as advertise based on the condition-map. Otherwise it is withdraw(2).
ROW juniBgpPeerAddressFamilyConditionalAdvRowStatus	1.3.6.1.4.1.4874.2.2.29.1.30.1.6	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo, destroy
juniBgpPeerGroupAddressFamilyConditionalAdvTable	1.3.6.1.4.1.4874.2.2.29.1.31		not-accessible	The Juniper BGP Peer Group Address Family Conditional Advertisement Table describes the BGP conditional advertisement attributes in an Address Family for a peer-group.
juniBgpPeerGroupAddressFamilyConditionalAdvEntry	1.3.6.1.4.1.4874.2.2.29.1.31.1		not-accessible	The Juniper BGP Peer Group Address Family Conditional Advertisement Entry describes a specific conditional advertisement entry in an Address Family for a peer-group.
JUN juniBgpPeerGroupAddressFamilyConditionalAdvAdvertiseMap	1.3.6.1.4.1.4874.2.2.29.1.31.1.1	JuniBgpAdvertiseMapName	not-accessible	The route-map for conditional advertisement.
STR juniBgpPeerGroupAddressFamilyConditionalAdvConditionMap	1.3.6.1.4.1.4874.2.2.29.1.31.1.2	DisplayString	read-create	The condition-map to apply for this conditional advertisement entry.
T/F juniBgpPeerGroupAddressFamilyConditionalAdvIsExistMap	1.3.6.1.4.1.4874.2.2.29.1.31.1.3	TruthValue	read-create	Set this value to true(1) if the condition-map specified should be applied as an exist-map. If the condition-map should be applied as a non-exist-map, set it to false(2).
I32 juniBgpPeerGroupAddressFamilyConditionalAdvSequenceNum	1.3.6.1.4.1.4874.2.2.29.1.31.1.4	Integer32	read-create	The sequence number of this conditional advertisement entry.
JUN juniBgpPeerGroupAddressFamilyConditionalAdvStatus	1.3.6.1.4.1.4874.2.2.29.1.31.1.5	JuniBgpConditionalAdvStatus	read-only	This value will be advertise(1) if the status of this advertise-map is evaluated as advertise based on the condition-map. Otherwise it is withdraw(2).
ROW juniBgpPeerGroupAddressFamilyConditionalAdvRowStatus	1.3.6.1.4.1.4874.2.2.29.1.31.1.6	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo, destroy
juniBgpConformance	1.3.6.1.4.1.4874.2.2.29.2
juniBgpCompliances	1.3.6.1.4.1.4874.2.2.29.2.1
juniBgpCompliance	1.3.6.1.4.1.4874.2.2.29.2.1.1			Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when the juniBgpDefaultIPv4Unicast object was added to the general cofiguation group.
juniBgpCompliance2	1.3.6.1.4.1.4874.2.2.29.2.1.2			Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when the original route destination was added as an index to each of the route configuration tables.
juniBgpCompliance3	1.3.6.1.4.1.4874.2.2.29.2.1.3			Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when the peer and peer-group local-as support was added.
juniBgpCompliance4	1.3.6.1.4.1.4874.2.2.29.2.1.4			Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support was added for adding unicast BGP routes into a multicast view.
juniBgpCompliance5	1.3.6.1.4.1.4874.2.2.29.2.1.5			Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when the juniBgpRedistributeInternal object was added to the general configuration group and the history pool size objects were obsoleted and the ability to unconfigure BGP attributes from the MIB was added.
juniBgpCompliance6	1.3.6.1.4.1.4874.2.2.29.2.1.6			Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for four-octet AS-numbers, dynamic capability negotiation, iBGP multipath, confederation peers filter-list, and address family maximum prefix strict was added.
juniBgpCompliance7	1.3.6.1.4.1.4874.2.2.29.2.1.7			Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for advertise-best-external-to-internal was added.
juniBgpCompliance8	1.3.6.1.4.1.4874.2.2.29.2.1.8			Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for maximum-paths eiBGP and other features were added.
juniBgpCompliance9	1.3.6.1.4.1.4874.2.2.29.2.1.9			Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for send-label was added.
juniBgpCompliance10	1.3.6.1.4.1.4874.2.2.29.2.1.10			Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for a route-map for default-information originate and neighbor ... default-originate was added.
juniBgpCompliance11	1.3.6.1.4.1.4874.2.2.29.2.1.11			Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when MIB support for graceful restart was added
juniBgpCompliance12	1.3.6.1.4.1.4874.2.2.29.2.1.12			Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when BGP storage support was removed and when MIB support for next-hop-unchanged was added.
juniBgpCompliance13	1.3.6.1.4.1.4874.2.2.29.2.1.13			Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for BGP BFD was added.
juniBgpCompliance14	1.3.6.1.4.1.4874.2.2.29.2.1.14			Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for ibgp-singlehop was added.
juniBgpCompliance15	1.3.6.1.4.1.4874.2.2.29.2.1.15			Obsolete compliance statement for entities which implement the Juniper BGP MIB. This statement became obsolete when support for conditional advertisement was added.
juniBgpCompliance16	1.3.6.1.4.1.4874.2.2.29.2.1.16			The compliance statement for entities which implement the Juniper BGP MIB.
juniBgpConfGroups	1.3.6.1.4.1.4874.2.2.29.2.2
juniBgpGeneralConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.1			Obsolete collection of objects providing general management of BGP in a Juniper product. This group became obsolete when the juniBgpDefaultIPv4Unicast object was added.
juniBgpStatisticsConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.2			A collection of objects providing statistics of BGP operations in a Juniper product.
juniBgpConfederationPeerConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.3			Deprecated object providing management of BGP-specific confederation peers in a Juniper product. This group became deprecated when support for four-octet AS-numbers was added.
juniBgpPeerConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.4			Obsolete collection of objects providing management of BGP peers in a Juniper product. This group became obsolete when the juniBgpPeerLocalAsNumber object was added.
juniBgpAfiSafiPeerConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.5			A collection of objects providing management of BGP-specific AFI and SAFI peers in a Juniper product.
juniBgpPeerAddressFamilyConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.6			Obsolete collection of objects providing management of BGP peer address families in a Juniper product. This group became obsolete when the ability to unconfigure attributes using the MIB was added.
juniBgpPeerGroupConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.7			Obsolete collection of objects providing management of BGP peer groups in a Juniper product. This group became obsolete when the juniBgpPeerGroupLocalAsNumber object was added.
juniBgpPeerGroupAddressFamilyConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.8			Obsolete collection of objects providing management of BGP peer group address families in a Juniper product. This group was obsoleted when the ability to unconfigure BGP attributes using the MIB was added.
juniBgpRouteConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.9			Obsolete collection of objects providing management of BGP routes in a Juniper product. This group became obsolete when the original route destination was added as an index to each of the tables.
juniBgpNetworkConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.10			Obsolete collection of objects providing management of BGP networks in a Juniper product. This group was obsoleted when the ability to unconfigure BGP attributes using the MIB was added.
juniBgpAggregateConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.11			Obsolete collection of objects providing consolidation of BGP route information in a Juniper product. This group was obsoleted when the ability to unconfigure BGP attributes using the MIB was added.
juniBgpVrfConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.12			Obsolete collection of objects providing management of BGP-specific VPN routing forwarding (VRF) characteristics in a Juniper product. This group became obsolete when the juniBgpVrfAddUnicastRoutesToMulticastView object was added.
juniBgpAddressFamilyConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.13			Obsolete collection of objects providing management of BGP address families in a Juniper product. This group was obsoleted when the ability to unconfigure BGP attributes using the MIB was added.
juniBgpStorageConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.14			Obsolete collection of objects providing management of BGP characteristics in a Juniper product that will not take affect until reboot. This group became obsolete when the history pool size objects were obsoleted.
juniBgpGeneralConfGroup2	1.3.6.1.4.1.4874.2.2.29.2.2.15			Obsolete collection of objects providing general management in a Juniper product. This group became obsolete when the juniBgpRedistributeInternal object and unconfigure support were added.
juniBgpNewRouteConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.16			Obsolete collection of objects providing management of BGP routes in a Juniper product. This group was obsoleted when label was replaced by in-label and out-label.
juniBgpPeerConfGroup2	1.3.6.1.4.1.4874.2.2.29.2.2.17			Obsolete collection of objects providing management of BGP peers in a Juniper product. This group became obsolete when the ability to unconfigure BGP attributes from the MIB was added.
juniBgpPeerGroupConfGroup2	1.3.6.1.4.1.4874.2.2.29.2.2.18			Obsolete collection of objects providing management of BGP peer groups in a Juniper product. This group was obsoleted when the ability to unconfigure BGP attributes using the MIB was added.
juniBgpVrfConfGroup2	1.3.6.1.4.1.4874.2.2.29.2.2.19			Obsolete collection of objects providing management of BGP-specific VPN routing forwarding (VRF) characteristics in a Juniper product. This group was obsoleted when the ability to unconfigure BGP attributes using the MIB was added.
juniBgpGeneralConfGroup3	1.3.6.1.4.1.4874.2.2.29.2.2.20			Obsolete collection of objects providing general management of BGP in a Juniper product. This group became obsolete when four-octet AS-numbers and maximum-paths iBGP support was added.
juniBgpStorageConfGroup2	1.3.6.1.4.1.4874.2.2.29.2.2.21			Obsolete collection of objects providing management of BGP characteristics in a Juniper product that will not take affect until reboot. This group became obsolete when storage heap size objects were obsoleted.
juniBgpPeerConfGroup3	1.3.6.1.4.1.4874.2.2.29.2.2.22			Obsolete collection of objects providing management of BGP peers in a Juniper product. This groups was obsoleted when support for four octet AS numbers was added.
juniBgpPeerAddressFamilyConfGroup2	1.3.6.1.4.1.4874.2.2.29.2.2.23			Obsolete collection of objects providing management of BGP peer address families in a Juniper product. This group was obsoleted when support for ORFs was added.
juniBgpPeerGroupConfGroup3	1.3.6.1.4.1.4874.2.2.29.2.2.24			Obsolete collection of objects providing management of BGP peer groups in a Juniper product. This group was obsoleted when support for dynamic capability negotiation was added.
juniBgpPeerGroupAddressFamilyConfGroup2	1.3.6.1.4.1.4874.2.2.29.2.2.25			Obsolete collection of objects providing management of BGP peer group address families in a Juniper product. This group was obsoleted when support for ORFs was added.
juniBgpNetworkConfGroup2	1.3.6.1.4.1.4874.2.2.29.2.2.26			A collection of objects providing management of BGP networks in a Juniper product.
juniBgpAggregateConfGroup2	1.3.6.1.4.1.4874.2.2.29.2.2.27			A collection of objects providing consolidation of BGP route information in a Juniper product.
juniBgpVrfConfGroup3	1.3.6.1.4.1.4874.2.2.29.2.2.28			Obsolete collection of objects providing management of BGP-specific VPN routing forwarding (VRF) characteristics in a Juniper product. This group was obsoleted when support for iBGP multipath was added.
juniBgpAddressFamilyConfGroup2	1.3.6.1.4.1.4874.2.2.29.2.2.29			Obsolete collection of objects providing management of BGP address-family groups in a Juniper product. This group was obsoleted when support for administrative distance was added.
juniBgpGeneralConfGroup4	1.3.6.1.4.1.4874.2.2.29.2.2.30			Obsolete collection of objects providing general management of BGP in a Juniper product. This group became obsolete when support for advertise-best-external-to-internal was added.
juniBgpFourOctetConfederationPeerConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.31			An object providing management of BGP-specific confederation peers in a Juniper product.
juniBgpPeerConfGroup4	1.3.6.1.4.1.4874.2.2.29.2.2.32			Obsolete collection of objects providing management of BGP peers in a Juniper product. This group was obsoleted when support for site-of-origin was added.
juniBgpPeerAddressFamilyConfGroup3	1.3.6.1.4.1.4874.2.2.29.2.2.33			Obsolete collection of objects providing management of BGP peer address families in a Juniper product. This group was obsoleted when support for send-label was added
juniBgpPeerGroupConfGroup4	1.3.6.1.4.1.4874.2.2.29.2.2.34			Obsolete collection of objects providing management of BGP peer groups in a Juniper product. This group was obsoleted when support for site-of-origin was added.
juniBgpPeerGroupAddressFamilyConfGroup3	1.3.6.1.4.1.4874.2.2.29.2.2.35			Obsolete collection of objects providing management of BGP peer group address families in a Juniper product. This group was obsoleted when support for send-label was added.
juniBgpVrfConfGroup4	1.3.6.1.4.1.4874.2.2.29.2.2.36			Obsolete collection of objects providing management of BGP-specific VPN routing forwarding (VRF) characteristics in a Juniper product. This group was obsoleted when support for eiBGP multipath was added.
juniBgpDeprecatedGroup	1.3.6.1.4.1.4874.2.2.29.2.2.37			A collection of deprecated objects that continue to be supported on some current Juniper products.
juniBgpNewRouteConfGroup2	1.3.6.1.4.1.4874.2.2.29.2.2.38			Obsolete collection of objects providing management of BGP routes in a Juniper product. This group was obsoleted when support for leaked flag attribute of the BGP route was added.
juniBgpGeneralConfGroup5	1.3.6.1.4.1.4874.2.2.29.2.2.39			Obsolete collection of objects providing general management of BGP in a Juniper product. This group was obsoleted when MIB support for graceful restart was added.
juniBgpPeerConfGroup5	1.3.6.1.4.1.4874.2.2.29.2.2.40			Obsolete collection of objects providing management of BGP peers in a Juniper product. This group was obsoleted when support for the new dynamic capability negotiation draft was added.
juniBgpPeerGroupConfGroup5	1.3.6.1.4.1.4874.2.2.29.2.2.41			Obsolete collection of objects providing management of BGP peer groups in a Juniper product. This group was obsoleted when support for the new dynamic capability negotiation draft was added.
juniBgpVrfConfGroup5	1.3.6.1.4.1.4874.2.2.29.2.2.42			Obsolete collection of objects providing management of BGP-specific VPN routing forwarding (VRF) characteristics in a Juniper product. This group was obsoleted when support for carrier's carrier was added.
juniBgpAddressFamilyConfGroup3	1.3.6.1.4.1.4874.2.2.29.2.2.43			Obsolete collection of objects providing management of BGP address families in a Juniper product. This group was obsoleted when support for check-vpn-next-hops was added.
juniBgpStorageConfGroup3	1.3.6.1.4.1.4874.2.2.29.2.2.44			Obsolete collection of objects providing management of BGP characteristics in a Juniper product that will not take affect until reboot. This group became obsolete when storage support objects were obsoleted.
juniBgpNewRouteConfGroup3	1.3.6.1.4.1.4874.2.2.29.2.2.45			Obsolete collection of objects providing management of BGP routes in a Juniper product. This group was obsoleted when MIB support for graceful restart was added.
juniBgpPeerAddressFamilyConfGroup4	1.3.6.1.4.1.4874.2.2.29.2.2.46			Obsolete collection of objects providing management of BGP peer address families in a Juniper product. This group was obsoleted when support for a route-map for neighbor ... default-originate was added.
juniBgpPeerGroupAddressFamilyConfGroup4	1.3.6.1.4.1.4874.2.2.29.2.2.47			Obsolete collection of objects providing management of BGP peer group address families in a Juniper product. This group was obsoleted when support for a route-map for neighbor ... default-originate was added.
juniBgpVrfConfGroup6	1.3.6.1.4.1.4874.2.2.29.2.2.48			Obsolete collection of objects providing management of BGP-specific VPN routing forwarding (VRF) characteristics in a Juniper product. This group was obsoleted when the BGP-specific carrier's carrier flag was removed.
juniBgpAddressFamilyConfGroup4	1.3.6.1.4.1.4874.2.2.29.2.2.49			Obsolete collection of objects providing management of BGP address families in a Juniper product. This group was obsoleted when support for the route-map option in default-information originate was added.
juniBgpPeerAddressFamilyConfGroup5	1.3.6.1.4.1.4874.2.2.29.2.2.50			Obsolete collection of objects providing management of BGP peer address families in a Juniper product. This group was obsoleted when MIB support for graceful restart was added.
juniBgpPeerGroupAddressFamilyConfGroup5	1.3.6.1.4.1.4874.2.2.29.2.2.51			Obsolete collection of objects providing management of BGP peer group address families in a Juniper product. This group was obsoleted when MIB support for next-hop-unchanged was added.
juniBgpAddressFamilyConfGroup5	1.3.6.1.4.1.4874.2.2.29.2.2.52			Obsolete collection of objects providing management of BGP address families in a Juniper product. This group was obsoleted when MIB support for graceful restart was added.
juniBgpPeerConfGroup6	1.3.6.1.4.1.4874.2.2.29.2.2.53			Obsolete collection of objects providing management of BGP peers in a Juniper product. This group was obsoleted when MIB support for graceful restart was added.
juniBgpPeerGroupConfGroup6	1.3.6.1.4.1.4874.2.2.29.2.2.54			Obsolete collection of objects providing management of BGP peer groups in a Juniper product. This group was obsoleted when MIB support for graceful restart was added.
juniBgpPeerDynamicCapabilityConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.55			A collection of objects providing management of BGP dynamic capability negotiation.
juniBgpGeneralConfGroup6	1.3.6.1.4.1.4874.2.2.29.2.2.56			A collection of objects providing general management of BGP in a Juniper product.
juniBgpPeerConfGroup7	1.3.6.1.4.1.4874.2.2.29.2.2.57			Obsolete collection of objects providing management of BGP peers in a Juniper product. This group was obsoleted when support for BFD was added.
juniBgpPeerAddressFamilyConfGroup6	1.3.6.1.4.1.4874.2.2.29.2.2.58			Obsolete collection of objects providing management of BGP peer address families in a Juniper product. This group was obsoleted when MIB support for next-hop-unchanged was added.
juniBgpPeerGroupConfGroup7	1.3.6.1.4.1.4874.2.2.29.2.2.59			Obsolete collection of objects providing management of BGP peer groups in a Juniper product. This group was obsoleted when support for BFD was added.
juniBgpNewRouteConfGroup4	1.3.6.1.4.1.4874.2.2.29.2.2.60			A collection of objects providing management of BGP routes in a Juniper product.
juniBgpAddressFamilyConfGroup6	1.3.6.1.4.1.4874.2.2.29.2.2.61			Obsolete collection of objects providing management of BGP address families in a Juniper product. This group was obsoleted when BGP-created IP dynamic interface profile support has been removed.
juniBgpVrfConfGroup7	1.3.6.1.4.1.4874.2.2.29.2.2.62			A collection of objects providing management of BGP-specific VPN routing forwarding (VRF) characteristics in a Juniper product.
juniBgpPeerAddressFamilyConfGroup7	1.3.6.1.4.1.4874.2.2.29.2.2.63			A collection of objects providing management of BGP peer address families in a Juniper product.
juniBgpPeerGroupAddressFamilyConfGroup6	1.3.6.1.4.1.4874.2.2.29.2.2.64			A collection of objects providing management of BGP peer group address families in a Juniper product.
juniBgpAddressFamilyConfGroup7	1.3.6.1.4.1.4874.2.2.29.2.2.65			A collection of objects providing management of BGP address families in a Juniper product.
juniBgpPeerConfGroup8	1.3.6.1.4.1.4874.2.2.29.2.2.66			Obsolete collection of objects providing management of BGP peers in a Juniper product. This group was obsoleted when support for ibgp-singlehop was added.
juniBgpPeerGroupConfGroup8	1.3.6.1.4.1.4874.2.2.29.2.2.67			Obsolete collection of objects providing management of BGP peers in a Juniper product. This group was obsoleted when support for ibgp-singlehop was added.
juniBgpPeerConfGroup9	1.3.6.1.4.1.4874.2.2.29.2.2.68			A collection of objects providing management of BGP peers in a Juniper product.
juniBgpPeerGroupConfGroup9	1.3.6.1.4.1.4874.2.2.29.2.2.69			A collection of objects providing management of BGP peer groups in a Juniper product.
juniBgpPeerAddressFamilyConditionalAdvConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.70			A collection of objects providing management of BGP Conditional Advertisement for peers in a Juniper product.
juniBgpPeerGroupAddressFamilyConditionalAdvConfGroup	1.3.6.1.4.1.4874.2.2.29.2.2.71			A collection of objects providing management of BGP Conditional Advertisement for peer groups in a Juniper product.

RFC description

Manages BGP protocol configuration including peers, address families, and graceful restart for Juniper routers.

Start monitoring Juniper E-series router (BGP configuration/peer sessions/route stats) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Juniper-BGP-MIB