| OID symbolic | OID numeric | Type | Access | Description |
|---|
| juniIpv6ProfileMIB | 1.3.6.1.4.1.4874.2.2.68 | | | The IPv6 Profile MIB for the Juniper Networks enterprise. |
| juniIpv6ProfileObjects | 1.3.6.1.4.1.4874.2.2.68.1 | | | |
| juniIpv6Profile | 1.3.6.1.4.1.4874.2.2.68.1.1 | | | |
| juniIpv6ProfileTable | 1.3.6.1.4.1.4874.2.2.68.1.1.1 | | not-accessible | The entries in this table describe profiles for configuring IP
interfaces.
Entries in this table are created/deleted as a side-effect of
corresponding operations to the juniProfileNameTable in the
Juniper-PROFILE-MIB. |
| juniIpv6ProfileEntry | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1 | | not-accessible | A profile describing configuration of an IPv6 interface. |
| U32 juniIpv6ProfileId | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.1 | Unsigned32 | not-accessible | The integer identifier associated with this profile. A value for this
identifier is determined by locating or creating a profile name in the
juniProfileNameTable. |
| JUN juniIpv6ProfileSetMap | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.2 | JuniSetMap | read-write | A bitmap representing which objects in this entry have been explicitly
configured. See the definition of the JuniSetMap TEXTUAL-CONVENTION for
details of use.
The INDEX object(s) and this object are excluded from representation
(i.e. their bits are never set).
When a SET request does not explicitly configure JuniSetMap, bits in
JuniSetMap are set as a side-effect of configuring other profile
attributes in the same entry.
If, however, a SET request explicitly configures JuniSetMap, the
explicitly configured value overrides 1) any previous bit settings, and
2) any simultaneous 'side-effect' settings that would otherwise occur.
Once set, bits can only be cleared by explicitly configuring
JuniSetMap. |
| JUN juniIpv6ProfileRouterName | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.3 | JuniName | read-write | The virtual router to which an IPv6 interface configured by this
profile will be assigned, if other mechanisms do not otherwise specify a
virtual router assignment. |
| ADR juniIpv6ProfileIpv6Addr | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.4 | InetAddressIPv6 | read-write | An IPv6 address to be used by an IPv6 interface configured by this
profile. This object will have a value of 0::0 for an unnumbered
interface. |
| I32 juniIpv6ProfileIpv6MaskLen | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.5 | Integer32 | read-write | An IPv6 address mask length to be used by an IPv6 interface configured
by this profile. This object will have a value of 0 for an unnumbered
interface. |
| I32 juniIpv6ProfileMtu | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.6 | Integer32 | read-write | The configured MTU size for this IPv6 network interface. If set to
zero, the default MTU size, as determined by the underlying network
media, is used. |
| JUN juniIpv6ProfileSrcAddrValidEnable | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.7 | JuniEnable | read-write | Enable/disable whether source addresses in received IPv6 packets are
validated. Validation is performed by looking up the source IPv6
address in the routing database and determining whether the packet
arrived on the expected interface; if not, the packet is discarded. |
| STR juniIpv6ProfileInheritNumString | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.8 | DisplayString | read-write | The text identifier of the numbered interface, associated with the
specified virtual router, whose IPv6 address is used as the source
address when transmitting IPv6 packets on unnumbered remote access user
links. Types/formats/examples for this string include:
Loopback
loopback
'loopback 0'
ATM Virtual Circuit
atm /.
'atm 3/1.100'
Ethernet
{ fastEthernet | gigabitEthernet } /
'fastEthernet 3/0'
'gigabitEthernet 3/0'
Ethernet VLAN
{ fastEthernet | gigabitEthernet } /:
'fastEthernet 3/0:1000'
'gigabitEthernet 3/0:1000'
Channelized Serial
serial /:[/]*
'serial 3/0:4' (T1/E1)
'serial 3/0:2/4' (T3/E3)
'serial 3/0:2/1/1/4' (OC3/OC12 - channelized DS3)
'serial 3/0:2/1/1/1/4' (OC3/OC12 - virtual tributaries)
Other formats may be supported over time.
An empty string indicates the referenced interface is unspecified, e.g.,
when this IPv6 interface is numbered. |
| JUN juniIpv6ProfileNdEnabled | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.9 | JuniEnable | read-write | Enable/disable ND for this IPv6 network interface. |
| JUN juniIpv6ProfileNdManagedConfig | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.10 | JuniEnable | read-write | Enable/disable ND managed config for this IPv6 network interface. |
| JUN juniIpv6ProfileNdOtherConfig | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.11 | JuniEnable | read-write | Enable/disable ND other config for this IPv6 network interface. |
| JUN juniIpv6ProfileNdSuppressRa | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.12 | JuniEnable | read-write | Enable/disable ND suppress RA for this IPv6 network interface. |
| I32 juniIpv6ProfileNdRaInterval | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.13 | Integer32 | read-write | The configured interval between IPv6 RA transmissions on the interface. |
| I32 juniIpv6ProfileNdRaLifeTime | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.14 | Integer32 | read-write | The configured RA lifetime for this IPv6 network interface. |
| I32 juniIpv6ProfileNdReachableTime | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.15 | Integer32 | read-write | The configured RA reachable time for this IPv6 network interface. |
| ADR juniIpv6ProfileNdPrefix | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.16 | Ipv6AddressPrefix | read-write | The prefix associated with the this interface. |
| I32 juniIpv6ProfileNdPrefixLength | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.17 | Integer32 | read-write | The length of the prefix (in bits). |
| JUN juniIpv6ProfileNdPrefixOnLinkFlag | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.18 | JuniEnable | read-write | This object has the value 'true(1)', if this
prefix can be used for on-link determination
and the value 'false(2)' otherwise. |
| JUN juniIpv6ProfileNdPrefixAutonomousFlag | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.19 | JuniEnable | read-write | Autonomous address configuration flag. When
true(1), indicates that this prefix can be used
for autonomous address configuration (i.e. can
be used to form a local interface address).
If false(2), it is not used to autoconfigure
a local interface address. |
| I32 juniIpv6ProfileNdPrefixPreferredLifetime | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.20 | Integer32 | read-write | It is the length of time in seconds that this
prefix will remain preferred, i.e. time until
deprecation. A value of 4,294,967,295 represents
infinity.
The address generated from a deprecated prefix
should no longer be used as a source address in
new communications, but packets received on such
an interface are processed as expected. |
| I32 juniIpv6ProfileNdPrefixValidLifetime | 1.3.6.1.4.1.4874.2.2.68.1.1.1.1.21 | Integer32 | read-write | It is the length of time in seconds that this
prefix will remain valid, i.e. time until
invalidation. A value of 4,294,967,295 represents
infinity.
The address generated from an invalidated prefix
should not appear as the destination or source
address of a packet. |
| juniIpv6ProfileMIBConformance | 1.3.6.1.4.1.4874.2.2.68.4 | | | |
| juniIpv6ProfileMIBCompliances | 1.3.6.1.4.1.4874.2.2.68.4.1 | | | |
| juniIpv6ProfileCompliance | 1.3.6.1.4.1.4874.2.2.68.4.1.1 | | | Obsolete Compliance statement for systems supporting IPv6 configuration
profiles. This statement became obsolete when added ND support. |
| juniIpv6ProfileCompliance1 | 1.3.6.1.4.1.4874.2.2.68.4.1.2 | | | Compliance statement for systems supporting IPv6 configuration
profiles, incorporating support of ND on dynamical interface. |
| juniIpv6ProfileMIBGroups | 1.3.6.1.4.1.4874.2.2.68.4.2 | | | |
| juniIpv6ProfileGroup | 1.3.6.1.4.1.4874.2.2.68.4.2.1 | | | An obsolete collection of objects providing management of IPv6 Profile
functionality in a Juniper product. This statement became obsolete
when added ND support. |
| juniIpv6ProfileGroup1 | 1.3.6.1.4.1.4874.2.2.68.4.2.2 | | | The basic collection of objects providing management of IPv6 Profile
functionality in a Juniper product. |
