DNOS-BGP-MIB

All MIBs › DNOS-BGP-MIB

Organization: Dell, Inc.

Last Updated: 2011-01-26

Category: Protocol: BGP, Technology: Routing, Vendor: Dell/DNOS

Description: Extends Border Gateway Protocol (BGP) management with Dell DNOS-specific objects for routing policy and peering.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DNOS-BGP-MIB?

DNOS-BGP-MIB extends standard Border Gateway Protocol management with Dell Networking Operating System (DNOS)-specific objects, part of a BGP "Flex package" for Dell/Broadcom-based DNOS routing platforms. It exposes BGP-specific configuration and state data such as peer/neighbor sessions, routing policy controls, and peering parameters beyond what the standard BGP4-MIB provides. In a monitoring context it supports fault and performance monitoring of the routing control plane, revealing BGP session/peer state (established, idle, active) which is critical to detecting route flapping or lost peering sessions. It explicitly extends the standard IETF BGP4-MIB and is meant to be used alongside it rather than as a replacement. It is deployed on Dell DNOS-based switches and routers acting as BGP speakers in data center or enterprise routing environments. Engineers can download the DNOS-BGP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DNOS-BGP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Dell DNOS switch/router

Monitoring Examples

No sample_objects were supplied; based on the description an admin would poll DNOS BGP peer-state objects (extending the standard bgpPeerTable model) to confirm neighbor sessions remain in the Established state. A peer unexpectedly dropping to Idle or Active state would indicate a routing adjacency failure needing investigation. Because this MIB augments BGP4-MIB, monitoring typically combines both MIBs' objects for a full picture.

What Can Be Monitored

BGP peer/session state
BGP routing policy configuration
peer established/idle status

Imported Objects

From DELL-REF-MIB

dnOS	OBJECT-IDENTITY

From RFC1213-MIB

DisplayString

From SNMPv2-SMI

Counter32
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

TEXTUAL-CONVENTION
TruthValue

How to Use in IPNetwork Monitor

Example using agentBGPInOpens OID:

Select a Dell Networking OS (DNOS) switch/router (BGP extensions) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type agentBGPInOpens into the Find box to locate it in the OID tree, then select it and click OK. The total number of BGP OPEN messages received since BGP counters were last cleared. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
TIK agentBGPCountersCleared	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.2.1	TimeTicks	read-only	The time since BGP counters were last cleared, in seconds.
G32 agentBGPDecProcAdds	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.3.1.9	Gauge32	read-only	Number of prefixes added during the decision process. For phase 1, this is the number of prefixes that pass inbound policy. For phase 2, this is the number of prefixes added to the BGP routing table. For phase 3, this is the number of prefixes added to the Adj-RIB-Out.
G32 agentBGPDecProcAddsIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.5.1.9	Gauge32	read-only	Number of prefixes added during the decision process. For phase 1, this is the number of prefixes that pass inbound policy. For phase 2, this is the number of prefixes added to the BGP routing table. For phase 3, this is the number of prefixes added to the Adj-RIB-Out.
G32 agentBGPDecProcDels	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.3.1.11	Gauge32	read-only	Number of prefixes deleted during the decision process. For phase 1, this is the number of prefixes that previously passed inbound policy but no longer pass. For phase 2, this is the number of prefixes removed from the BGP routing table. For phase 3, this is the number of prefixes removed from the Adj-RIB-Out.
G32 agentBGPDecProcDelsIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.5.1.11	Gauge32	read-only	Number of prefixes deleted during the decision process. For phase 1, this is the number of prefixes that previously passed inbound policy but no longer pass. For phase 2, this is the number of prefixes removed from the BGP routing table. For phase 3, this is the number of prefixes removed from the Adj-RIB-Out.
U32 agentBGPDecProcDeltaT	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.3.1.2	Unsigned32	read-only	How long since this decision process ran. The time is given in seconds.
U32 agentBGPDecProcDeltaTIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.5.1.2	Unsigned32	read-only	How long since this decision process ran. The time is given in seconds.
G32 agentBGPDecProcDuration	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.3.1.8	Gauge32	read-only	How long the decision process ran. Milliseconds.
G32 agentBGPDecProcDurationIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.5.1.8	Gauge32	read-only	How long the decision process ran. Milliseconds.
agentBGPDecProcEntry	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.3.1		not-accessible	Information about execution of a single decision process phase.
U32 agentBGPDecProcGenId	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.3.1.5	Unsigned32	read-only	The global generation ID when the decision process ran.
U32 agentBGPDecProcGenIdIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.5.1.5	Unsigned32	read-only	The global generation ID when the decision process ran.
C32 agentBGPDecProcIndex	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.3.1.1	Counter32	not-accessible	Integer that uniquely identifies a decision process run. This value is incremented each time BGP runs one phase of the decision process.
agentBGPDecProcIPv6Entry	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.5.1		not-accessible	Information about execution of a single decision process phase.
C32 agentBGPDecProcIPv6Index	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.5.1.1	Counter32	not-accessible	Integer that uniquely identifies a decision process run. This value is incremented each time BGP runs one phase of the decision process.
agentBGPDecProcIPv6Table	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.5		not-accessible	This table contains information about the twenty most recent executions of any of the three decision process phases. The most recent information is at the end of the table. This table is applicable to IPv6 address family only.
G32 agentBGPDecProcMods	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.3.1.10	Gauge32	read-only	Number of prefixes modified during the decision process. For phase 1, this is the number of prefixes that pass inbound policy. For phase 2, this is the number of routes modified. For phase 3, this is the number of routes modified in the Adj-RIB-Out.
G32 agentBGPDecProcModsIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.5.1.10	Gauge32	read-only	Number of prefixes modified during the decision process. For phase 1, this is the number of prefixes that pass inbound policy. For phase 2, this is the number of routes modified. For phase 3, this is the number of routes modified in the Adj-RIB-Out.
IP agentBGPDecProcPeer	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.3.1.7	IpAddress	read-only	This variable is only valid when phase 1 is run for a single peer. In this case, this variable is the IP address of the peer for which phase 1 was run.
IP agentBGPDecProcPeerIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.5.1.7	IpAddress	read-only	This variable is only valid when phase 1 is run for a single peer. In this case, this variable is the IP address of the peer for which phase 1 was run.
U32 agentBGPDecProcPhase	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.3.1.3	Unsigned32	read-only	Which of the three decision process phases was run.
U32 agentBGPDecProcPhaseIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.5.1.3	Unsigned32	read-only	Which of the three decision process phases was run.
STR agentBGPDecProcReason	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.3.1.6	DisplayString	read-only	Reason why the decision process was run.
STR agentBGPDecProcReasonIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.5.1.6	DisplayString	read-only	Reason why the decision process was run.
agentBGPDecProcTable	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.3		not-accessible	This table contains information about the twenty most recent executions of any of the three decision process phases. The most recent information is at the end of the table. This table is applicable to IPv4 address family only.
U32 agentBGPDecProcUpdateGroup	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.3.1.4	Unsigned32	read-only	This variable is only valid when agentBGPDecProcPhase is 3. When the phase is 3, this variable identifies the outbound update group for which phase 3 was run. When the variable has a value of 65535 then it means that the corresponding agentBGPDecProcEntry does not belong to any outbound update group
U32 agentBGPDecProcUpdateGroupIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.5.1.4	Unsigned32	read-only	This variable is only valid when agentBGPDecProcPhase is 3. When the phase is 3, this variable identifies the outbound update group for which phase 3 was run. When the variable has a value of 65535 then it means that the corresponding agentBGPDecProcIPv6Entry does not belong to any outbound update group
C32 agentBGPInKeepalives	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.2.8	Counter32	read-only	The total number of BGP KEEPALIVE messages received since BGP counters were last cleared.
C32 agentBGPInNotifications	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.2.6	Counter32	read-only	The total number of BGP NOTIFICATION messages received since BGP counters were last cleared.
C32 agentBGPInOpensEx	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.2.2	Counter32	read-only	The total number of BGP OPEN messages received since BGP counters were last cleared.
C32 agentBGPInRouteRefreshes	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.2.10	Counter32	read-only	The total number of BGP ROUTE REFRESH messages received since BGP counters were last cleared.
C32 agentBGPInUpdates	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.2.4	Counter32	read-only	The total number of BGP UPDATE messages received since BGP counters were last cleared.
G32 agentBGPInUpdatesMax	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.2.12	Gauge32	read-only	The maximum rate of BGP UPDATE messages received. The rate is given in packets per second.
agentBGPMessageStatsGroup	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.2
C32 agentBGPOutKeepalives	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.2.9	Counter32	read-only	The total number of BGP KEEPALIVE messages transmitted since BGP counters were last cleared.
C32 agentBGPOutNotifications	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.2.7	Counter32	read-only	The total number of BGP NOTIFICATION messages transmitted since BGP counters were last cleared.
C32 agentBGPOutOpens	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.2.3	Counter32	read-only	The total number of BGP OPEN messages transmitted since BGP counters were last cleared.
C32 agentBGPOutRouteRefreshes	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.2.11	Counter32	read-only	The total number of BGP ROUTE REFRESH messages transmitted since BGP counters were last cleared.
C32 agentBGPOutUpdates	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.2.5	Counter32	read-only	The total number of BGP UPDATE messages transmitted since BGP counters were last cleared.
G32 agentBGPOutUpdatesMax	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.2.13	Gauge32	read-only	The maximum rate of BGP UPDATE messages transmitted. The rate is given in packets per second.
agentBGPPeerEntry	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1		not-accessible	Entry containing information about the connection with a BGP peer.
C32 agentBGPPeerInKeepalives	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.8	Counter32	read-only	The number of BGP KEEPALIVE messages received from this peer.
G32 agentBGPPeerInMaxNlriPerUpdate	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.26	Gauge32	read-only	The maximum number of IPv4 prefixes in any single UPDATE message from this peer.
G32 agentBGPPeerInMaxNlriPerUpdateIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.38	Gauge32	read-only	The maximum number of IPv6 prefixes in any single UPDATE message from this peer.
G32 agentBGPPeerInMinNlriPerUpdate	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.28	Gauge32	read-only	The minimum number of IPv4 prefixes in any single UPDATE message from this peer.
G32 agentBGPPeerInMinNlriPerUpdateIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.40	Gauge32	read-only	The minimum number of IPv6 prefixes in any single UPDATE message from this peer.
C32 agentBGPPeerInNotifications	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.6	Counter32	read-only	The number of BGP NOTIFICATION messages received from this peer.
C32 agentBGPPeerInOpens	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.2	Counter32	read-only	The number of BGP OPEN messages received from this peer.
G32 agentBGPPeerInPfxAccepted	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.24	Gauge32	read-only	The number of IPv4 prefixes received from this peer that may be considered to be included in the BGP route table. This includes all current prefixes whose path does not have an AS path loop and whose BGP NEXT HOP is resolved.
G32 agentBGPPeerInPfxAcceptedIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.36	Gauge32	read-only	The number of IPv6 prefixes received from this peer that may be considered to be included in the BGP route table. This includes all current prefixes whose path does not have an AS path loop and whose BGP NEXT HOP is resolved.
C32 agentBGPPeerInPfxAdv	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.18	Counter32	read-only	The number of IPv4 prefixes received from this peer.
C32 agentBGPPeerInPfxAdvIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.30	Counter32	read-only	The number of IPv6 prefixes received from this peer.
G32 agentBGPPeerInPfxCurrent	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.22	Gauge32	read-only	The number of IPv4 prefixes this peer is currently advertising to this router and that have passed inbound policy.
G32 agentBGPPeerInPfxCurrentIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.34	Gauge32	read-only	The number of IPv6 prefixes this peer is currently advertising to this router and that have passed inbound policy.
G32 agentBGPPeerInPfxRejected	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.25	Gauge32	read-only	The number of IPv4 prefixes from this peer that did not pass inbound policy.
G32 agentBGPPeerInPfxRejectedIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.37	Gauge32	read-only	The number of IPv6 prefixes from this peer that did not pass inbound policy.
C32 agentBGPPeerInPfxWithdrawn	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.20	Counter32	read-only	The number of IPv4 prefixes this peer has withdrawn.
C32 agentBGPPeerInPfxWithdrawnIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.32	Counter32	read-only	The number of IPv6 prefixes this peer has withdrawn.
C32 agentBGPPeerInRouteRefreshes	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.10	Counter32	read-only	The number of BGP ROUTE REFRESH messages received from this peer.
C32 agentBGPPeerInTotalMessages	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.12	Counter32	read-only	The total number of BGP messages of all types received from this peer.
C32 agentBGPPeerInUpdates	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.4	Counter32	read-only	The number of BGP UPDATE messages received from this peer.
C32 agentBGPPeerOutKeepalives	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.9	Counter32	read-only	The number of BGP KEEPALIVE messages transmitted to this peer.
G32 agentBGPPeerOutMaxNlriPerUpdate	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.27	Gauge32	read-only	The maximum number of IPv4 prefixes in any single UPDATE message sent to this peer.
G32 agentBGPPeerOutMaxNlriPerUpdateIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.39	Gauge32	read-only	The maximum number of IPv6 prefixes in any single UPDATE message sent to this peer.
G32 agentBGPPeerOutMinNlriPerUpdate	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.29	Gauge32	read-only	The minimum number of IPv4 prefixes in any single UPDATE message sent to this peer.
G32 agentBGPPeerOutMinNlriPerUpdateIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.41	Gauge32	read-only	The minimum number of IPv6 prefixes in any single UPDATE message sent to this peer.
C32 agentBGPPeerOutNotifications	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.7	Counter32	read-only	The number of BGP NOTIFICATION messages transmitted to this peer.
C32 agentBGPPeerOutOpens	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.3	Counter32	read-only	The number of BGP OPEN messages transmitted to this peer.
C32 agentBGPPeerOutPfxAdv	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.19	Counter32	read-only	The number of IPv4 prefixes advertised to this peer.
C32 agentBGPPeerOutPfxAdvIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.31	Counter32	read-only	The number of IPv6 prefixes advertised to this peer.
G32 agentBGPPeerOutPfxCurrent	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.23	Gauge32	read-only	The number of IPv4 prefixes this router is currently advertising to this peer.
G32 agentBGPPeerOutPfxCurrentIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.35	Gauge32	read-only	The number of IPv6 prefixes this router is currently advertising to this peer.
C32 agentBGPPeerOutPfxWithdrawn	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.21	Counter32	read-only	The number of IPv4 prefixes this router has withdrawn in UPDATE messages to this peer.
C32 agentBGPPeerOutPfxWithdrawnIPv6	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.33	Counter32	read-only	The number of IPv6 prefixes this router has withdrawn in UPDATE messages to this peer.
C32 agentBGPPeerOutRouteRefreshes	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.11	Counter32	read-only	The number of BGP ROUTE REFRESH messages transmitted to this peer.
C32 agentBGPPeerOutTotalMessages	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.13	Counter32	read-only	The total number of BGP messages of all types transmitted to this peer.
C32 agentBGPPeerOutUpdates	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.5	Counter32	read-only	The number of BGP UPDATE messages transmitted to this peer.
IP agentBGPPeerRemoteAddr	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.1	IpAddress	read-only	The remote IP address of this entry's BGP peer.
agentBGPPeerTable	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4		not-accessible	BGP peer table. This table contains, one entry per BGP peer, information about connections with BGP peers.
C32 agentBGPPeerUpdateQueueDrops	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.17	Counter32	read-only	The number of UPDATE messages from this peer that could not be added to the UPDATE queue because the queue was full.
G32 agentBGPPeerUpdateQueueHigh	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.15	Gauge32	read-only	The maximum length (or high water mark) of this peer.s UPDATE queue, in bytes.
G32 agentBGPPeerUpdateQueueLen	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.14	Gauge32	read-only	After receiving a BGP UPDATE message, BGP places each UPDATE on a per-neighbor queue before processing the UPDATE. This variable gives the current length of this peer's UPDATE queue, in bytes.
U32 agentBGPPeerUpdateQueueLimit	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.4.1.16	Unsigned32	read-only	The maximum number of bytes of received UPDATE messages that may be queued for this peer at any given time.
C32 agentBGPQueueDrops	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.1.1.1.5	Counter32	read-only	The number of items dropped because the work queue was full.
agentBGPQueueEntry	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.1.1.1		not-accessible	Information on a specific BGP work queue.
agentBGPQueueGroup	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.1
G32 agentBGPQueueHigh	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.1.1.1.4	Gauge32	read-only	The high water mark of the number of items in the work queue.
U32 agentBGPQueueIndex	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.1.1.1.1	Unsigned32	not-accessible	Index value for this work queue.
G32 agentBGPQueueLength	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.1.1.1.3	Gauge32	read-only	The number of items currently in the work queue.
U32 agentBGPQueueLimit	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.1.1.1.6	Unsigned32	read-only	The maximum number of items this queue can hold.
STR agentBGPQueueName	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.1.1.1.2	DisplayString	read-only	Name of an BGP work queue.
agentBGPQueueTable	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.1.1		not-accessible	Table lists information about BGP work queue utilization.
INT agentBGPSnmpAllTrapFlag	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.6.1	INTEGER	read-write	Enable standard traps defined in RFC 4273.
agentBGPSnmpTrapFlagsConfigGroup	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5.6
fastPathBGP	1.3.6.1.4.1.674.10895.5000.2.6132.1.1.5			The MIB definitions for Border Gateway Protocol Flex package.

RFC description

Border Gateway Protocol (BGP) queue and work queue monitoring for Dell/DNOS routing devices.

Start monitoring Dell Networking OS (DNOS) switch/router (BGP extensions) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DNOS-BGP-MIB