All MIBs › HUAWEI-TUNNEL-TE-MIB
Organization: Huawei Technologies Co.,Ltd.
Last Updated: 2013-08-28
Category: MPLS and Traffic Engineering, Vendor: Huawei
Description: Huawei tunnel traffic engineering MIB for managing MPLS-TE tunnel attributes, bandwidth reservations, and path computation.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is HUAWEI-TUNNEL-TE-MIB?
HUAWEI-TUNNEL-TE-MIB is a Huawei enterprise MIB for managing MPLS Traffic Engineering (TE) tunnels, covering tunnel attributes, bandwidth reservations, and path computation/binding information on Huawei routing platforms. It falls into the configuration and traffic-engineering category of MIBs, exposing data about how MPLS-TE tunnels are provisioned and bound to underlying paths rather than raw interface counters. Its monitoring relevance is in verifying tunnel and bandwidth-reservation state as an indicator of the health and correct operation of the MPLS-TE control plane and forwarding paths, rather than hardware sensors. As an MPLS-TE extension it implicitly depends on standard MPLS-TE concepts (e.g. RSVP-TE signaling and the IETF MPLS-TE MIB family) even though no module description text was available to confirm this explicitly. It is typically deployed on Huawei core/edge routers participating in an MPLS-TE-enabled service provider or enterprise WAN backbone. Engineers can download the HUAWEI-TUNNEL-TE-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-TUNNEL-TE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Huawei MPLS-TE capable router
Monitoring Examples
No sample objects were provided for this module, so specific object/table names cannot be cited; based on its description, an administrator would typically monitor MPLS-TE tunnel binding and bandwidth-reservation state to confirm tunnels are established along their intended paths and that reserved bandwidth matches configuration.
This MIB depends on
Related MIBs
Imported Objects
From HUAWEI-MIB
| hwDatacomm | OBJECT-IDENTITY |
From IF-MIB
| InterfaceIndex |
From MPLS-LSR-STD-MIB
| MplsIndexType |
From MPLS-TC-STD-MIB
| MplsExtendedTunnelId | |
| MplsTunnelIndex | |
| MplsTunnelInstanceIndex |
From SNMP-FRAMEWORK-MIB
| SnmpAdminString |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| BITS | |
| Counter32 | |
| Counter64 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| RowStatus | |
| TimeStamp | |
| TruthValue |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| hwTunnelTeMib | 1.3.6.1.4.1.2011.5.25.151 | This MIB contains private managed object definitions for the binding information. | ||
| hwTunnelTeMibObject | 1.3.6.1.4.1.2011.5.25.151.1 | |||
| hwTunnelDiffServTable | 1.3.6.1.4.1.2011.5.25.151.1.1 | not-accessible | The table describes the different service mode of tunnel. | |
| hwTunnelDiffServEntry | 1.3.6.1.4.1.2011.5.25.151.1.1.1 | not-accessible | Interface different service mode attribute configuration. | |
| NUM hwTunnelDiffServIndex | 1.3.6.1.4.1.2011.5.25.151.1.1.1.1 | InterfaceIndex | not-accessible | Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. Managers should obtain new values for row creation in this table by reading mplsTunnelIndexNext. When the MPLS signalling protocol is rsvp(2),this value should be equal to the value signalled in the Tunnel ID of the session object. When the MPLS signalling protocol is crldp(3) this value should be equal to the value signalled in the LSP ID. Reference to MPLS-TE-STD-MIB. |
| INT hwTunnelDiffServMode | 1.3.6.1.4.1.2011.5.25.151.1.1.1.2 | INTEGER | read-only | Different service mode of TE interface, default is uniform. |
| INT hwTunnelDiffServServiceClass | 1.3.6.1.4.1.2011.5.25.151.1.1.1.3 | INTEGER | read-only | PHB in the ingress PE, the value must be be,af1,af2,af3,af4,ef,cs6,cs7.The default class is invalidClass(255). |
| INT hwTunnelDiffServColor | 1.3.6.1.4.1.2011.5.25.151.1.1.1.4 | INTEGER | read-only | Remarked color of packet in the ingress PE, the value must be green,yellow,red.The default color is invalidColor(255). |
| OCT hwTunnelTeFlowQueue | 1.3.6.1.4.1.2011.5.25.151.1.1.1.5 | OCTET STRING | read-only | Name of flow-queue template. |
| hwTunnelTeVsiTable | 1.3.6.1.4.1.2011.5.25.151.1.2 | not-accessible | The table describes the VPN binding of Tunnel. | |
| hwTunnelTeVsiEntry | 1.3.6.1.4.1.2011.5.25.151.1.2.1 | not-accessible | The L2VPN VSI binding configuration of tunnel interface. | |
| NUM hwTunnelTeVsiIndex | 1.3.6.1.4.1.2011.5.25.151.1.2.1.1 | InterfaceIndex | not-accessible | Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. Managers should obtain new values for row creation in this table by reading mplsTunnelIndexNext. When the MPLS signalling protocol is rsvp(2),this value should be equal to the value signalled in the tunnel ID of the session object. When the MPLS signalling protocol is crldp(3) this value should be equal to the value signalled in the LSP ID. Reference to MPLS-TE-STD-MIB. |
| OCT hwTunnelTeVsiName | 1.3.6.1.4.1.2011.5.25.151.1.2.1.2 | OCTET STRING | not-accessible | The name of VSI that the TE interface bind. |
| I32 hwTunnelTeVsiCir | 1.3.6.1.4.1.2011.5.25.151.1.2.1.3 | Integer32 | read-only | The Committed Information Rate of the VSI. |
| I32 hwTunnelTeVsiPir | 1.3.6.1.4.1.2011.5.25.151.1.2.1.4 | Integer32 | read-only | The Peak Information Rate of the VSI. |
| OCT hwTunnelTeVsiFlowQueue | 1.3.6.1.4.1.2011.5.25.151.1.2.1.5 | OCTET STRING | read-only | Name of flow-queue template. |
| hwTunnelTeVllTable | 1.3.6.1.4.1.2011.5.25.151.1.3 | not-accessible | The table describes the VLL binding of tunnel. | |
| hwTunnelTeVllEntry | 1.3.6.1.4.1.2011.5.25.151.1.3.1 | not-accessible | The VLL binding configuration of tunnel interface. | |
| NUM hwTunnelTeVllIndex | 1.3.6.1.4.1.2011.5.25.151.1.3.1.1 | InterfaceIndex | not-accessible | Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. Managers should obtain new values for row creation in this table by reading mplsTunnelIndexNext. When the MPLS signalling protocol is rsvp(2),this value should be equal to the value signalled in the tunnel ID of the session object. When the MPLS signalling protocol is crldp(3) this value should be equal to the value signalled in the LSP ID. Reference to MPLS-TE-STD-MIB. |
| OCT hwTunnelTeVllInterfaceName | 1.3.6.1.4.1.2011.5.25.151.1.3.1.2 | OCTET STRING | not-accessible | The interface name of VLL binding. |
| I32 hwTunnelTeVllCir | 1.3.6.1.4.1.2011.5.25.151.1.3.1.3 | Integer32 | read-only | The Committed Information Rate of the VLL. |
| I32 hwTunnelTeVllPir | 1.3.6.1.4.1.2011.5.25.151.1.3.1.4 | Integer32 | read-only | The Peak Information Rate of the VLL. |
| OCT hwTunnelTeVllFlowQueue | 1.3.6.1.4.1.2011.5.25.151.1.3.1.5 | OCTET STRING | read-only | Name of flow-queue template. |
| hwTunnelTeL3vpnTable | 1.3.6.1.4.1.2011.5.25.151.1.4 | not-accessible | The table describes the L3VPN binding of tunnel. | |
| hwTunnelTeL3vpnEntry | 1.3.6.1.4.1.2011.5.25.151.1.4.1 | not-accessible | The L3VPN binding configuration of tunnel interface. | |
| NUM hwTunnelTeL3vpnIndex | 1.3.6.1.4.1.2011.5.25.151.1.4.1.1 | InterfaceIndex | not-accessible | Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. Managers should obtain new values for row creation in this table by reading mplsTunnelIndexNext. When the MPLS signalling protocol is rsvp(2),this value should be equal to the value signalled in the tunnel ID of the session object. When the MPLS signalling protocol is crldp(3) this value should be equal to the value signalled in the LSP ID. Reference to MPLS-TE-STD-MIB. |
| OCT hwTunnelTeL3vpnName | 1.3.6.1.4.1.2011.5.25.151.1.4.1.2 | OCTET STRING | not-accessible | The name of VPN instance that the TE interface bind. |
| I32 hwTunnelTeL3vpnCir | 1.3.6.1.4.1.2011.5.25.151.1.4.1.3 | Integer32 | read-only | The Committed Information Rate of the L3VPN. |
| I32 hwTunnelTeL3vpnPir | 1.3.6.1.4.1.2011.5.25.151.1.4.1.4 | Integer32 | read-only | The Peak Information Rate of the L3VPN. |
| OCT hwTunnelTeL3vpnFlowQueue | 1.3.6.1.4.1.2011.5.25.151.1.4.1.5 | OCTET STRING | read-only | Name of flow-queue template. |
| hwTunnelTeStatisticsTable | 1.3.6.1.4.1.2011.5.25.151.1.5 | not-accessible | The table describes the up/down state transition counts of the TE tunnel interface. | |
| hwTunnelTeStatisticsEntry | 1.3.6.1.4.1.2011.5.25.151.1.5.1 | not-accessible | The up/down state transition counts of TE tunnel interface. The index of the table is hwTunnelTeStatisticsIfIndex. | |
| NUM hwTunnelTeStatisticsIfIndex | 1.3.6.1.4.1.2011.5.25.151.1.5.1.1 | InterfaceIndex | not-accessible | Uniquely identifies a set of tunnel instances between a pair of ingress and egress LSRs. Managers should obtain new values for row creation in this table by reading mplsTunnelIndexNext. |
| U32 hwTunnelTeUpDownStatistics | 1.3.6.1.4.1.2011.5.25.151.1.5.1.2 | Unsigned32 | read-only | Describes the up/down transition counts of the TE tunnel interface. |
| TIM hwTunnTeCounterDiscontinuityTime | 1.3.6.1.4.1.2011.5.25.151.1.5.1.3 | TimeStamp | read-only | The value of sysUpTime on the most recent occasion at which this interface's up/down transition counters suffered a discontinuity. |
| hwCtTemplateTable | 1.3.6.1.4.1.2011.5.25.151.1.6 | not-accessible | The table describes the CT template configuration on the device. | |
| hwCtTemplateEntry | 1.3.6.1.4.1.2011.5.25.151.1.6.1 | not-accessible | The CT template configuration on the device. The index of the table is hwCtTemplateIndex. | |
| I32 hwCtTemplateIndex | 1.3.6.1.4.1.2011.5.25.151.1.6.1.1 | Integer32 | not-accessible | It uniquely identifies a set of CT templates. Managers should obtain new values for row creation in this table by reading hwCtTemplateIndex. |
| OCT hwCtTemplateName | 1.3.6.1.4.1.2011.5.25.151.1.6.1.2 | OCTET STRING | read-create | The CT template name. |
| U32 hwCtTemplateCt0 | 1.3.6.1.4.1.2011.5.25.151.1.6.1.3 | Unsigned32 | read-create | The CT0 bandwidth of the CT template. |
| U32 hwCtTemplateCt1 | 1.3.6.1.4.1.2011.5.25.151.1.6.1.4 | Unsigned32 | read-create | The CT1 bandwidth of the CT template. |
| U32 hwCtTemplateCt2 | 1.3.6.1.4.1.2011.5.25.151.1.6.1.5 | Unsigned32 | read-create | The CT2 bandwidth of the CT template. |
| U32 hwCtTemplateCt3 | 1.3.6.1.4.1.2011.5.25.151.1.6.1.6 | Unsigned32 | read-create | The CT3 bandwidth of the CT template. |
| U32 hwCtTemplateCt4 | 1.3.6.1.4.1.2011.5.25.151.1.6.1.7 | Unsigned32 | read-create | The CT4 bandwidth of the CT template. |
| U32 hwCtTemplateCt5 | 1.3.6.1.4.1.2011.5.25.151.1.6.1.8 | Unsigned32 | read-create | The CT5 bandwidth of the CT template. |
| U32 hwCtTemplateCt6 | 1.3.6.1.4.1.2011.5.25.151.1.6.1.9 | Unsigned32 | read-create | The CT6 bandwidth of the CT template. |
| U32 hwCtTemplateCt7 | 1.3.6.1.4.1.2011.5.25.151.1.6.1.10 | Unsigned32 | read-create | The CT7 bandwidth of the CT template. |
| INT hwCtTemplateCommit | 1.3.6.1.4.1.2011.5.25.151.1.6.1.11 | INTEGER | read-create | The commit flag of the CT template,1 indicates commit,0 indicates not commit. |
| ROW hwCtTemplateRowStatus | 1.3.6.1.4.1.2011.5.25.151.1.6.1.12 | RowStatus | read-create | This object is used to create and delete rows in the CT template. |
| hwCtConfigTunnelCtTable | 1.3.6.1.4.1.2011.5.25.151.1.7 | not-accessible | The table describes the CT configuration in the TE tunnel interface. | |
| hwCtConfigTunnelCtEntry | 1.3.6.1.4.1.2011.5.25.151.1.7.1 | not-accessible | The table describes the CT configuration in the TE tunnel interface. The index of the table is hwCtConfigTunnelCtIfIndex. | |
| NUM hwCtConfigTunnelCtIfIndex | 1.3.6.1.4.1.2011.5.25.151.1.7.1.1 | InterfaceIndex | not-accessible | Uniquely identifies a set of tunnels between a pair of ingress and egress LSRs. Managers should obtain new values for row creation in this table by reading mplsTunnelIndexNext. When the MPLS signalling protocol is rsvp(2),this value should be equal to the value signalled in the tunnel ID of the session object. When the MPLS signalling protocol is crldp(3) this value should be equal to the value signalled in the LSP ID. Reference to MPLS-TE-STD-MIB. |
| OCT hwCtConfigTunnelName | 1.3.6.1.4.1.2011.5.25.151.1.7.1.2 | OCTET STRING | read-only | The name of the TE tunnel interface. |
| INT hwCtConfigTunnelCommit | 1.3.6.1.4.1.2011.5.25.151.1.7.1.3 | INTEGER | read-only | The commit flag of the TE tunnel interface,1 indicates commit,0 indicates not commit. |
| OCT hwCtConfigTemplateName | 1.3.6.1.4.1.2011.5.25.151.1.7.1.4 | OCTET STRING | read-only | The CT template name. |
| U32 hwCtConfigTunnelCt0Band | 1.3.6.1.4.1.2011.5.25.151.1.7.1.5 | Unsigned32 | read-only | The CT0 bandwidth value of the TE tunnel interface. |
| U32 hwCtConfigTunnelCt1Band | 1.3.6.1.4.1.2011.5.25.151.1.7.1.6 | Unsigned32 | read-only | The CT1 bandwidth value of the TE tunnel interface. |
| U32 hwCtConfigTunnelCt2Band | 1.3.6.1.4.1.2011.5.25.151.1.7.1.7 | Unsigned32 | read-only | The CT2 bandwidth value of the TE tunnel interface. |
| U32 hwCtConfigTunnelCt3Band | 1.3.6.1.4.1.2011.5.25.151.1.7.1.8 | Unsigned32 | read-only | The CT3 bandwidth value of the TE tunnel interface. |
| U32 hwCtConfigTunnelCt4Band | 1.3.6.1.4.1.2011.5.25.151.1.7.1.9 | Unsigned32 | read-only | The CT4 bandwidth value of the TE tunnel interface. |
| U32 hwCtConfigTunnelCt5Band | 1.3.6.1.4.1.2011.5.25.151.1.7.1.10 | Unsigned32 | read-only | The CT5 bandwidth value of the TE tunnel interface. |
| U32 hwCtConfigTunnelCt6Band | 1.3.6.1.4.1.2011.5.25.151.1.7.1.11 | Unsigned32 | read-only | The CT6 bandwidth value of the TE tunnel interface. |
| U32 hwCtConfigTunnelCt7Band | 1.3.6.1.4.1.2011.5.25.151.1.7.1.12 | Unsigned32 | read-only | The CT7 bandwidth value of the TE tunnel interface. |
| hwCtStatisticsTable | 1.3.6.1.4.1.2011.5.25.151.1.8 | not-accessible | The table describes flow statistics of the TE tunnel interface VPN configuration. | |
| hwCtStatisticsEntry | 1.3.6.1.4.1.2011.5.25.151.1.8.1 | not-accessible | The table describes the statistics in the TE tunnel interface with CT configuration. The index of the table is hwCtStatisticsIfIndex. | |
| NUM hwCtStatisticsIfIndex | 1.3.6.1.4.1.2011.5.25.151.1.8.1.1 | InterfaceIndex | not-accessible | Uniquely identifies a set of tunnels between a pair of ingress and egress LSRs. Managers should obtain new values for row creation in this table by reading mplsTunnelIndexNext. When the MPLS signalling protocol is rsvp(2),this value should be equal to the value signalled in the tunnel ID of the session object. When the MPLS signalling protocol is crldp(3) this value should be equal to the value signalled in the LSP ID. Reference to MPLS-TE-STD-MIB. |
| OCT hwCtStatisticsTunnelName | 1.3.6.1.4.1.2011.5.25.151.1.8.1.2 | OCTET STRING | read-only | The name of the TE tunnel interface. |
| C64 hwCtStatisticsCt0OutByteRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.3 | Counter64 | read-only | It counts the rate in bytes/sec out from the CT0 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt0OutPktRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.4 | Counter64 | read-only | It counts the rate in packets/sec out from the CT0 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt0OutPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.5 | Counter64 | read-only | It counts the out packets from the CT0 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt0OutPktByte | 1.3.6.1.4.1.2011.5.25.151.1.8.1.6 | Counter64 | read-only | It counts the out bytes from the CT0 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt0OutErrorPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.7 | Counter64 | read-only | It counts the error packets from the CT0 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt1OutByteRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.8 | Counter64 | read-only | It counts the rate in bytes/sec out from CT1 the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt1OutPktRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.9 | Counter64 | read-only | It counts the rate in packets/sec out from the CT0 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt1OutPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.10 | Counter64 | read-only | It counts the out packets from the CT1 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt1OutPktByte | 1.3.6.1.4.1.2011.5.25.151.1.8.1.11 | Counter64 | read-only | It counts the out packet bytes from the CT1 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt1OutErrorPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.12 | Counter64 | read-only | It counts the error packets from the CT1 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt2OutByteRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.13 | Counter64 | read-only | It counts the rate in bytes/sec out from the CT2 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt2OutPktRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.14 | Counter64 | read-only | It counts the rate in packets/sec out from the CT2 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt2OutPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.15 | Counter64 | read-only | It counts the out packets from the CT2 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt2OutPktByte | 1.3.6.1.4.1.2011.5.25.151.1.8.1.16 | Counter64 | read-only | It counts the out packet bytes from the CT2 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt2OutErrorPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.17 | Counter64 | read-only | It counts the error packets from the CT2 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt3OutByteRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.18 | Counter64 | read-only | The CT3 out in bytes/sec out of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt3OutPktRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.19 | Counter64 | read-only | It counts the rate in packets/sec out from the CT0 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt3OutPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.20 | Counter64 | read-only | It counts the out packets from the CT3 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt3OutPktByte | 1.3.6.1.4.1.2011.5.25.151.1.8.1.21 | Counter64 | read-only | It counts the out packet bytes from the CT3 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt3OutErrorPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.22 | Counter64 | read-only | It counts the error packets from the CT0 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt4OutByteRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.23 | Counter64 | read-only | The CT4 out in bytes/sec out of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt4OutPktRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.24 | Counter64 | read-only | It counts the rate in packets/sec out from the CT4 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt4OutPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.25 | Counter64 | read-only | It counts the out packets from the CT4 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt4OutPktByte | 1.3.6.1.4.1.2011.5.25.151.1.8.1.26 | Counter64 | read-only | It counts the out packet bytes from the CT4 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt4OutErrorPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.27 | Counter64 | read-only | It counts the error packets from the CT4 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt5OutByteRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.28 | Counter64 | read-only | The CT5 out in bytes/sec out of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt5OutPktRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.29 | Counter64 | read-only | It counts the rate in packets/sec out from the CT5 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt5OutPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.30 | Counter64 | read-only | It counts the out packets from the CT5 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt5OutPktByte | 1.3.6.1.4.1.2011.5.25.151.1.8.1.31 | Counter64 | read-only | It counts the out packet bytes from the CT5 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt5OutErrorPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.32 | Counter64 | read-only | It counts the error packets from the CT5 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt6OutByteRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.33 | Counter64 | read-only | The CT6 out in bytes/sec out of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt6OutPktRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.34 | Counter64 | read-only | It counts the rate in packets/sec out from the CT6 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt6OutPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.35 | Counter64 | read-only | It counts the out packets from the CT6 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt6OutPktByte | 1.3.6.1.4.1.2011.5.25.151.1.8.1.36 | Counter64 | read-only | It counts the out packet bytes from the CT6 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt6OutErrorPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.37 | Counter64 | read-only | It counts the error packets from the CT6 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt7OutByteRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.38 | Counter64 | read-only | The CT7 out in bytes/sec out of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt7OutPktRate | 1.3.6.1.4.1.2011.5.25.151.1.8.1.39 | Counter64 | read-only | It counts the rate in packets/sec out from the CT7 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt7OutPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.40 | Counter64 | read-only | It counts the out packets from the CT7 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt7OutPktByte | 1.3.6.1.4.1.2011.5.25.151.1.8.1.41 | Counter64 | read-only | It counts the out packet bytes from the CT7 of the TE tunnel interface with VPN configuration. |
| C64 hwCtStatisticsCt7OutErrorPkt | 1.3.6.1.4.1.2011.5.25.151.1.8.1.42 | Counter64 | read-only | It counts the error packets from the CT7 of the TE tunnel interface with VPN configuration. |
| hwCtFlowTemplateTable | 1.3.6.1.4.1.2011.5.25.151.1.9 | not-accessible | The table describes max 8 of the CT-FLOW-Mapping template configuration on the device. | |
| hwCtFlowTemplateEntry | 1.3.6.1.4.1.2011.5.25.151.1.9.1 | not-accessible | The table describes the CT-FLOW-Mapping template configuration on the device. | |
| I32 hwCtFlowTemplateID | 1.3.6.1.4.1.2011.5.25.151.1.9.1.1 | Integer32 | not-accessible | The index of CT-FLOW templat. |
| OCT hwCtFlowTemplateName | 1.3.6.1.4.1.2011.5.25.151.1.9.1.11 | OCTET STRING | read-create | The name of CT-FLOW template. |
| INT hwCt0Cos | 1.3.6.1.4.1.2011.5.25.151.1.9.1.12 | INTEGER | read-create | The Value of class of service must be in 'be,af1,af2,af3,af4,ef,cs6,cs7'. |
| INT hwCt0Scheduler | 1.3.6.1.4.1.2011.5.25.151.1.9.1.13 | INTEGER | read-create | Scheduler name. |
| INT hwCt0Valid | 1.3.6.1.4.1.2011.5.25.151.1.9.1.14 | INTEGER | read-create | The state of CT-FLOW templat row. |
| INT hwCt1Cos | 1.3.6.1.4.1.2011.5.25.151.1.9.1.15 | INTEGER | read-create | The Value of class of service must be in 'be,af1,af2,af3,af4,ef,cs6,cs7'. |
| INT hwCt1Scheduler | 1.3.6.1.4.1.2011.5.25.151.1.9.1.16 | INTEGER | read-create | Scheduler name. |
| INT hwCt1Valid | 1.3.6.1.4.1.2011.5.25.151.1.9.1.17 | INTEGER | read-create | The state of CT-FLOW templat row. |
| INT hwCt2Cos | 1.3.6.1.4.1.2011.5.25.151.1.9.1.18 | INTEGER | read-create | The Value of class of service must be in 'be,af1,af2,af3,af4,ef,cs6,cs7'. |
| INT hwCt2Scheduler | 1.3.6.1.4.1.2011.5.25.151.1.9.1.19 | INTEGER | read-create | Scheduler name. |
| INT hwCt2Valid | 1.3.6.1.4.1.2011.5.25.151.1.9.1.20 | INTEGER | read-create | The state of CT-FLOW templat row. |
| INT hwCt3Cos | 1.3.6.1.4.1.2011.5.25.151.1.9.1.21 | INTEGER | read-create | The Value of class of service must be in 'be,af1,af2,af3,af4,ef,cs6,cs7'. |
| INT hwCt3Scheduler | 1.3.6.1.4.1.2011.5.25.151.1.9.1.22 | INTEGER | read-create | Scheduler name. |
| INT hwCt3Valid | 1.3.6.1.4.1.2011.5.25.151.1.9.1.23 | INTEGER | read-create | The state of CT-FLOW templat row. |
| INT hwCt4Cos | 1.3.6.1.4.1.2011.5.25.151.1.9.1.24 | INTEGER | read-create | The Value of class of service must be in 'be,af1,af2,af3,af4,ef,cs6,cs7'. |
| INT hwCt4Scheduler | 1.3.6.1.4.1.2011.5.25.151.1.9.1.25 | INTEGER | read-create | Scheduler name. |
| INT hwCt4Valid | 1.3.6.1.4.1.2011.5.25.151.1.9.1.26 | INTEGER | read-create | The state of CT-FLOW templat row. |
| INT hwCt5Cos | 1.3.6.1.4.1.2011.5.25.151.1.9.1.27 | INTEGER | read-create | The Value of class of service must be in 'be,af1,af2,af3,af4,ef,cs6,cs7'. |
| INT hwCt5Scheduler | 1.3.6.1.4.1.2011.5.25.151.1.9.1.28 | INTEGER | read-create | Scheduler name. |
| INT hwCt5Valid | 1.3.6.1.4.1.2011.5.25.151.1.9.1.29 | INTEGER | read-create | The state of CT-FLOW templat row. |
| INT hwCt6Cos | 1.3.6.1.4.1.2011.5.25.151.1.9.1.30 | INTEGER | read-create | The Value of class of service must be in 'be,af1,af2,af3,af4,ef,cs6,cs7'. |
| INT hwCt6Scheduler | 1.3.6.1.4.1.2011.5.25.151.1.9.1.31 | INTEGER | read-create | Scheduler name. |
| INT hwCt6Valid | 1.3.6.1.4.1.2011.5.25.151.1.9.1.32 | INTEGER | read-create | The state of CT-FLOW templat row. |
| INT hwCt7Cos | 1.3.6.1.4.1.2011.5.25.151.1.9.1.33 | INTEGER | read-create | The Value of class of service must be in 'be,af1,af2,af3,af4,ef,cs6,cs7'. |
| INT hwCt7Scheduler | 1.3.6.1.4.1.2011.5.25.151.1.9.1.34 | INTEGER | read-create | Scheduler name. |
| INT hwCt7Valid | 1.3.6.1.4.1.2011.5.25.151.1.9.1.35 | INTEGER | read-create | The state of CT-FLOW templat row. |
| INT hwCtFlowTemplateCommit | 1.3.6.1.4.1.2011.5.25.151.1.9.1.36 | INTEGER | read-create | The state of CT-FLOW templat commit. |
| ROW hwCtFlowTemplateRowStatus | 1.3.6.1.4.1.2011.5.25.151.1.9.1.51 | RowStatus | read-create | The state of CT-FLOW templat. |
| hwDsteInterfaceCfgTable | 1.3.6.1.4.1.2011.5.25.151.1.10 | not-accessible | The DS-TE configuration at interface. | |
| hwDsteInterfaceCfgEntry | 1.3.6.1.4.1.2011.5.25.151.1.10.1 | not-accessible | The DS-TE configuration at interface. | |
| NUM hwDsteIfIndex | 1.3.6.1.4.1.2011.5.25.151.1.10.1.1 | InterfaceIndex | not-accessible | A unique value, greater than zero, for eachinterface. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must remain constant at least from one re-initialization of the entity's network management system to the next re-initialization. |
| OCT hwAppliedCtFlowTemplateName | 1.3.6.1.4.1.2011.5.25.151.1.10.1.11 | OCTET STRING | read-create | The name of CT-FLOW template. |
| INT hwCtBandWidthShareCfg | 1.3.6.1.4.1.2011.5.25.151.1.10.1.12 | INTEGER | read-create | The Value of Ct BandWidth configuration for DS-TE. That must be in 'Share,UnShare'. |
| hwTunnelDsTeTrap | 1.3.6.1.4.1.2011.5.25.151.2 | |||
| NTF hwMplsFqShortage | 1.3.6.1.4.1.2011.5.25.151.2.1 | This notification is generated when FQ (flow-queue) template resources are shortage. | ||
| NTF hwMplsSqShortage | 1.3.6.1.4.1.2011.5.25.151.2.2 | This notification is generated when SQ (subscriber-queue) resources are shortage. | ||
| NTF hwMplsSqBandwidthExceed | 1.3.6.1.4.1.2011.5.25.151.2.3 | This notification is generated when the total bandwidth of SQ (subscriber-queue) exceeds 10G bit/s in one LPU. | ||
| NTF hwMplsHsbFqShortage | 1.3.6.1.4.1.2011.5.25.151.2.4 | This notification is generated when FQ (flow-queue) template resources in HSB are shortage. | ||
| NTF hwMplsHsbSqShortage | 1.3.6.1.4.1.2011.5.25.151.2.5 | This notification is generated when SQ (subscriber-queue) resources in HSB are shortage. | ||
| NTF hwMplsHsbSqBandwidthExceed | 1.3.6.1.4.1.2011.5.25.151.2.6 | This notification is generated when the total bandwidth of SQ (subscriber-queue) in HSB exceeds 10G bit/s in one LPU. | ||
| hwTunnelTeConformance | 1.3.6.1.4.1.2011.5.25.151.3 | |||
| hwTunnelTeCompliances | 1.3.6.1.4.1.2011.5.25.151.3.1 | |||
| hwTunnelTeCompliance | 1.3.6.1.4.1.2011.5.25.151.3.1.1 | The compliance statement for HUAWEI-TUNNEL-TE-MIB. | ||
| hwTunnelTeGroups | 1.3.6.1.4.1.2011.5.25.151.3.3 | |||
| hwTunnelDiffServGroup | 1.3.6.1.4.1.2011.5.25.151.3.3.1 | Describes the different service mode of tunnel. | ||
| hwTunnelTeVsiGroup | 1.3.6.1.4.1.2011.5.25.151.3.3.2 | Describes the VSI binding of tunnel. | ||
| hwTunnelTeVllGroup | 1.3.6.1.4.1.2011.5.25.151.3.3.3 | Describes the VLL binding of tunnel. | ||
| hwTunnelTeL3vpnGroup | 1.3.6.1.4.1.2011.5.25.151.3.3.4 | Describes the L3VPN binding of tunnel. | ||
| hwTunnelTeStatisticsGroup | 1.3.6.1.4.1.2011.5.25.151.3.3.5 | Describes the up/down count of the TE tunnel. | ||
| hwCtTemplateGroup | 1.3.6.1.4.1.2011.5.25.151.3.3.6 | Describes CT template. | ||
| hwCtConfigCtGroup | 1.3.6.1.4.1.2011.5.25.151.3.3.7 | Describes the CT configuration of the TE tunnel interface. | ||
| hwCtStatisticsGroup | 1.3.6.1.4.1.2011.5.25.151.3.3.8 | Describes the CT of the TE tunnel interface. | ||
| hwTunnelTeTrapGroup | 1.3.6.1.4.1.2011.5.25.151.3.3.9 | The HUAWEI Tunnel Te trap info. | ||
| hwCtFlowTemplateGroup | 1.3.6.1.4.1.2011.5.25.151.3.3.10 | The table describes the CT-FLOW-Mapping template configuration on the device. | ||
| hwDsteInterfaceCfgGroup | 1.3.6.1.4.1.2011.5.25.151.3.3.11 | The table describes the CT-FLOW-Mapping template configuration on the device. |
RFC description
Huawei MPLS traffic engineering tunnel configuration and DiffServ binding management.
Start monitoring Huawei MPLS-TE capable router with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.