HUAWEI-ADSL-MIB

All MIBs › HUAWEI-ADSL-MIB

Organization: Huawei Technologies Co.,Ltd.

Last Updated: 2012-12-27

Category: Domain: DSL, Vendor: Huawei

Description:

Huawei ADSL MIB for managing Asymmetric Digital Subscriber Line interfaces including line status, parameters, and performance counters.

Imported Objects

From ADSL-LINE-EXT-MIB

adslLineExtEntry

OBJECT-TYPE

From ADSL-LINE-MIB

adslAtucChanEntry	OBJECT-TYPE
adslAtucChanIntervalEntry	OBJECT-TYPE
adslAtucChanPerfDataEntry	OBJECT-TYPE
adslAtucIntervalEntry	OBJECT-TYPE
adslAtucPerfDataEntry	OBJECT-TYPE
adslAtucPhysEntry	OBJECT-TYPE
adslAturChanEntry	OBJECT-TYPE
adslAturChanIntervalEntry	OBJECT-TYPE
adslAturChanPerfDataEntry	OBJECT-TYPE
adslAturPhysEntry	OBJECT-TYPE
adslLineAlarmConfProfileEntry	OBJECT-TYPE
adslLineConfProfileEntry	OBJECT-TYPE
adslLineConfProfileName	OBJECT-TYPE
adslLineEntry	OBJECT-TYPE
adslLineMib	OBJECT-IDENTITY
adslMibObjects	OBJECT-IDENTITY
adslTraps	OBJECT-IDENTITY

From ADSL2-LINE-TC-MIB

Adsl2PsdMaskDs
Adsl2PsdMaskUs
Adsl2SymbolProtection
Adsl2TransmissionModeType

From HUAWEI-DEVICE-MIB

hwFrameIndex	OBJECT-TYPE
hwPortIndex	OBJECT-TYPE
hwSlotIndex	OBJECT-TYPE
hwSubslotIndex	OBJECT-TYPE

From HUAWEI-MIB

huaweiUtility

OBJECT-IDENTITY

From HUAWEI-TC-MIB

hwAlarmId	OBJECT-TYPE
hwAlarmSn	OBJECT-TYPE
hwAlarmTime	OBJECT-TYPE
hwCauseId	OBJECT-TYPE
hwTrapType	OBJECT-TYPE

From HWMUSA-DEV-MIB

hwIasConfigChangeTrapID

OBJECT-TYPE

From IF-MIB

ifIndex

OBJECT-TYPE

From PerfHist-TC-MIB

PerfIntervalCount

From RFC1213-MIB

ifType

From SNMPv2-MIB

sysName

OBJECT-TYPE

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DateAndTime
PhysAddress
RowStatus
TEXTUAL-CONVENTION

What Is HUAWEI-ADSL-MIB?

HUAWEI-ADSL-MIB is a Huawei vendor-specific module for managing Asymmetric Digital Subscriber Line (ADSL) interfaces on Huawei access equipment, covering line configuration, operational status, and performance monitoring for ADSL subscriber lines. Based on its stated purpose it exposes per-line objects for line status (up, training, or down), configurable line parameters, and performance counters tracking line quality over time. Its monitoring emphasis is squarely on line/hardware operational status: line up/down/training state functions much like a physical-layer health indicator, while performance counters (errored seconds, CRC/FEC errors, signal-to-noise margin) reveal degrading line quality before a full outage occurs. It likely complements the standard IETF ADSL-LINE-MIB/ADSL2-LINE-MIB conventions with Huawei-specific extensions rather than replacing them outright. It is deployed on Huawei DSLAM and broadband access equipment used by carriers to deliver and monitor residential/business ADSL service. Carriers deploying Huawei DSLAMs typically obtain a HUAWEI-ADSL-MIB download directly from Huawei's support portal to load into their SNMP management platform before polling line status.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-ADSL-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

What Can Be Monitored

ADSL line operational status (up/down/training)
line configuration parameters
line performance counters (errors, margin)

Supported Devices

Huawei DSLAM / ADSL broadband access equipment

Monitoring Examples

Without a supplied object list, the expected scenario is polling a per-line status object to confirm an ADSL line is synced rather than stuck in a training or down state, alongside performance counters for errored seconds or CRC errors that would reveal a noisy line degrading a subscriber's connection before it drops entirely. Because no concrete table or object names were provided for this module, a more specific polling example cannot be responsibly constructed.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwAdsl	1.3.6.1.4.1.2011.6.31			This MIB is used for defining Huawei's ADSL management MIB objects.
HWA hwadsl2ChConfProfMinProtectionDs	1.3.6.1.2.1.10.94.1.1.65543.1.14	HWADSLSYMBOLPROTECTION	read-write	Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection(0), halfSymbol(1), singleSymbol(2), twoSymbols(4), threeSymbols(6), fourSymbols(8), fiveSymbols(10), sixSymbols(12), sevenSymbols(14), eightSymbols(16), nineSymbols(18), tenSymbols(20), elevenSymbols(22), twelveSymbols(24), thirteenSymbols(26), fourteenSymbols(28), fifteenSymbols(30), sixteenSymbols(32), null(65535) The value multiply 1/2 is the real value of Noise Protection values.
HWA hwadsl2ChConfProfMinProtectionUs	1.3.6.1.2.1.10.94.1.1.65543.1.15	HWADSLSYMBOLPROTECTION	read-write	Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection(0), halfSymbol(1), singleSymbol(2), twoSymbols(4), threeSymbols(6), fourSymbols(8), fiveSymbols(10), sixSymbols(12), sevenSymbols(14), eightSymbols(16), nineSymbols(18), tenSymbols(20), elevenSymbols(22), twelveSymbols(24), thirteenSymbols(26), fourteenSymbols(28), fifteenSymbols(30), sixteenSymbols(32), null(65535) The value multiply 1/2 is the real value of Noise Protection values.
I32 hwadsl2L2ModeGuardTime	1.3.6.1.2.1.10.94.1.1.65543.1.27	Integer32	read-create	Guard Time before entering L2 Mode. Range: 0-1024 Default: 60 Unit: seconds
I32 hwadsl2L2ModeIntervalPowerValue	1.3.6.1.2.1.10.94.1.1.65543.1.29	Integer32	read-create	Maximum aggregate transmit power reduction per L2 request or L2 power trim. Range: 0-31 Default: 3 Unit: db
I32 hwadsl2L2ModeIntervalTime	1.3.6.1.2.1.10.94.1.1.65543.1.28	Integer32	read-create	The minimum interval between two records of L2 mode. Range: 0-255 Default: 255 Unit: seconds
I32 hwadsl2L2ModeL2Time	1.3.6.1.2.1.10.94.1.1.65543.1.65536	Integer32	read-create	This minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. It ranges from 0 to 255 seconds. Range: 0-255 Default: 30 Unit: seconds
I32 hwadsl2L2ModeMaxDataRate	1.3.6.1.2.1.10.94.1.1.65543.1.25	Integer32	read-create	Maximum Data Rate in L2 Mode. Range: 128-16384 Default: 1024 Unit: Kbps
I32 hwadsl2L2ModeMinDataRate	1.3.6.1.2.1.10.94.1.1.65543.1.24	Integer32	read-create	Minimum Data Rate in L2 Mode. Range: 128-16384 Unit: Kbps
I32 hwadsl2L2ModePayloadRateThreshold	1.3.6.1.2.1.10.94.1.1.65543.1.26	Integer32	read-create	Threshold for the Payload Rate Ratio. Range: 128-16384 Default: 128 Unit: Kbps
INT hwadsl2L2ModeState	1.3.6.1.2.1.10.94.1.1.65543.1.23	INTEGER	read-create	The state of L2 power management mode. Options: 1. disabled(1) - L2 power management mode is disabled 2. enabled(2) - L2 power management mode is enabled 3. forced(3) - L2 power management mode is forced Default: disabled(1)
I32 hwadsl2L2ModeTotalPowerValue	1.3.6.1.2.1.10.94.1.1.65543.1.30	Integer32	read-create	Total maximum aggregate transmit power reduction in L2. Range: 0-31 Default: 9 Unit: db
ADS hwadsl2LineTransAtucActual	1.3.6.1.2.1.10.94.3.1.17.1.65555	Adsl2TransmissionModeType	read-only	The actual transmission mode of the ATU-C. During ADSL line initialization, the ADSL Transceiver Unit - Remote terminal end (ATU-R) will determine the mode used for the link. This value will be limited a single transmission mode that is a subset of those modes enabled by the ATU-C and denoted by adslLineTransAtucConfig. After an initialization has occurred, its mode is saved as the 'Current' mode and is persistence should the link go down. This object returns 0 (i.e. BITS with no mode bit set) if the mode is not known.
hwAdsl2SCStateTable	1.3.6.1.2.1.10.94.1.1.65549		not-accessible	The table adsl2SCStatusTable contains status parameters of the ADSL2 sub-carriers. The indexes of this table are ifIndex and hwAdsl2SCStatusDirection.
OCT hwAdsl2SCStatusBitsAlloc	1.3.6.1.2.1.10.94.1.1.65549.1.3	OCTET STRING	read-only	The bits allocation per sub-carrier. An array of 256 octets (512 nibbles), designed for supporting up to 512 (downstream) sub-carriers. The number of utilized nibbles on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Nibble i (0 <= i < NSC) is set to a value in the range 0 to 15 to indicate that the respective downstream or upstream sub-carrier i has the same amount of bits allocation.
INT hwAdsl2SCStatusDirection	1.3.6.1.2.1.10.94.1.1.65549.1.1	INTEGER	not-accessible	The direction of the sub-carrier is either upstream or downstream. Options: 1. upstream(1) - Upstream sub-carrier 2. downstream(2) - Downstream sub-carrier
hwAdsl2SCStatusEntry	1.3.6.1.2.1.10.94.1.1.65549.1		not-accessible	The table adsl2SCStatusTable contains status parameters of the ADSL2 sub-carriers. The indexes of this entry are ifIndex and hwAdsl2SCStatusDirection.
OCT hwAdsl2SCStatusGainAlloc	1.3.6.1.2.1.10.94.1.1.65549.1.4	OCTET STRING	read-only	The gain allocation per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Value i (0 <= i < NSC) is in the range 0 to 4093 to indicate that the respective downstream or upstream sub-carrier i has the same amount of gain value. The gain value is represented as a multiple of 1/512 on a linear scale. Each value in this array is 16 bits wide and is stored in big endian format.
OCT hwAdsl2SCStatusLog	1.3.6.1.2.1.10.94.1.1.65549.1.5	OCTET STRING	read-only	An array of up to 512 real H(f) logarithmic representation values in dB for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Each array entry represents the real Hlog(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NSC). The real Hlog(f) value is represented as (6-m(i)/10), with m(i) in the range 0 to 1022. A special value m=1023 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 16 bits wide and is stored in big endian format.
OCT hwAdsl2SCStatusQln	1.3.6.1.2.1.10.94.1.1.65549.1.6	OCTET STRING	read-only	An array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Each array entry represents the QLN(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NSC). The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the range 0 to 254. A special value n(i)=255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the noise PSD is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 8 bits wide.
OCT hwAdsl2SCStatusSnr	1.3.6.1.2.1.10.94.1.1.65549.1.2	OCTET STRING	read-only	The SNR Margin per sub-carrier, expressing the ratio between the received signal power and received noise power per subscriber. It is an array of 512 octets, designed for supporting up to 512 (downstream) sub-carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Octet i (0 <= i < NSC) is set to a value in the range 0 to 254 to indicate that the respective downstream or upstream sub- carrier i has SNR of: (-32 + Adsl2SubcarrierSnr(i)/2) in dB (i.e., -32 to 95dB). The special value 255 means that no measurement could be done for the subcarrier because it is out of the PSD mask passband or that the noise PSD is out of range to be represented. Each value in this array is 8 bits wide.
OCT hwAdsl2SCStatusSnrMargin	1.3.6.1.2.1.10.94.1.1.65549.1.7	OCTET STRING	read-only	SNR Margin is the maximum increase in dB of the noise power received at the ATU (ATU-R on downstream direction and ATU-C on upstream direction), such that the BER requirements are met for all bearer channels received at the ATU. It ranges from -640 to 630 units of 0.1 dB (physical values are -64 to 63 dB).
OCT hwAdsl2SCStatusTxPSD	1.3.6.1.2.1.10.94.1.1.65549.1.8	OCTET STRING	read-only	The PSD MASK per sub-carrier.An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub-carriers. It ranges from -1400 to -300 units of 0.1 dBm/Hz (physical values are -140 to -30 dBm/Hz).
U32 hwadsl2TranMissionStardardMask	1.3.6.1.2.1.10.94.1.1.65543.1.20	Unsigned32	read-write	The tranmission stardard mask. The Mask bit and the corresponding Transmission Standard: 0x 1 1 1 1 1 1 ETSI T1.413 G992.5 G992.3 G992.2 G992.1 The Default BitMask: 0X0.
U32 hwadsl2TransMissionAnnexMask	1.3.6.1.2.1.10.94.1.1.65543.1.21	Unsigned32	read-write	The transMission annex Mask. The Mask bit and the corresponding Transmission Annex: 0x 1 1 1 1 1 Annex .J Annex .M Annex .L Annex .B Annex .A The Default BitMask: 0X0.
HWA hwadsl2TransMissionAnnexMScope	1.3.6.1.2.1.10.94.1.1.65543.1.22	HWADSL2ANNEXMSCOPE	read-create	Annex M expand scope: 1-Tone Index(7~32) 2-Tone Index(7~36) 3-Tone Index(7~40) 4-Tone Index(7~44) 5-Tone Index(7~48) 6-Tone Index(7~52) 7-Tone Index(7~56) 8-Tone Index(7~60) 9-Tone Index(7~64) -1-invalidValue
ADS hwadsl2TSSiPsdMaskDs	1.3.6.1.2.1.10.94.1.1.65543.1.19	Adsl2PsdMaskDs	read-write	The downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G992.3 or G992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G992.5. This is a string of 32 pairs of values in the following structure: Octets 0-1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 32, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
ADS hwadsl2TSSiPsdMaskUs	1.3.6.1.2.1.10.94.1.1.65543.1.39	Adsl2PsdMaskUs	read-write	The upstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G992.3 or G992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G992.5. This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 9-11, which are associated with a fourth breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCus. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 4, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
G32 hwadslAtucChanCodeGain	1.3.6.1.2.1.10.94.1.1.4.1.65544	Gauge32	read-only	Indicates Code Gain on downstream direction. It ranges from 0 to 16 units of 0.5 dB (physical values are 0 to 8 dB).
C32 hwadslAtucChanCrcBlks	1.3.6.1.2.1.10.94.1.1.10.1.65538	Counter32	read-only	Count of all blocks received with CRC anomalies since agent reset.
G32 hwadslAtucChanCurrINP	1.3.6.1.2.1.10.94.1.1.4.1.65536	Gauge32	read-only	Indicates Impulse Noise Protection on downstream direction. The value multiply 1/10000 is the real value. Unit: DMT Symbol
G32 hwAdslAtucChanCurrTxRate	1.3.6.1.2.1.10.94.1.1.65546.1.18	Gauge32	read-only	Actual transmit rate on this channel. Unit: bps
C32 hwadslAtucChanFecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65536	Counter32	read-only	Count of all blocks received with FEC anomalies since agent reset.
C32 hwadslAtucChanHecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65537	Counter32	read-only	Count of all blocks received with HEC anomalies since agent reset.
NUM hwAdslAtucChanIntervalCorrectedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.34	PerfIntervalCount	read-only	Count of all blocks received with errors that were corrected on this channel during this interval.
NUM hwadslAtucChanIntervalCrcBlks	1.3.6.1.2.1.10.94.1.1.12.1.65538	PerfIntervalCount	read-only	Count of all blocks received with CRC anomalies on this channel during this interval.
NUM hwadslAtucChanIntervalFecBlks	1.3.6.1.2.1.10.94.1.1.12.1.65536	PerfIntervalCount	read-only	Count of all blocks received with FRC anomalies on this channel during this interval.
NUM hwadslAtucChanIntervalHecBlks	1.3.6.1.2.1.10.94.1.1.12.1.65537	PerfIntervalCount	read-only	Count of all blocks received with HRC anomalies on this channel during this interval.
NUM hwAdslAtucChanIntervalReceivedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.32	PerfIntervalCount	read-only	Count of all encoded blocks received on this channel during this interval.
G32 hwadslAtucChanIntervalRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.12.1.65540	Gauge32	read-only	Count of units corrected by retransmission on this channel during this interval.
G32 hwadslAtucChanIntervalRtxCW	1.3.6.1.2.1.10.94.1.1.12.1.65539	Gauge32	read-only	Count of units request retransmission on this channel during this interval.
G32 hwadslAtucChanIntervalRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.12.1.65541	Gauge32	read-only	Count of units uncorrected by retransmission on this channel during this interval.
NUM hwAdslAtucChanIntervalTransmittedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.33	PerfIntervalCount	read-only	Count of all encoded blocks transmitted on this channel during this interval.
NUM hwAdslAtucChanIntervalUncorrectBlks	1.3.6.1.2.1.10.94.1.1.65546.1.35	PerfIntervalCount	read-only	Count of all blocks received with uncorrectable errors on this channel during this interval.
G32 hwadslAtucChanPcb	1.3.6.1.2.1.10.94.1.1.4.1.65545	Gauge32	read-only	Indicates Power Cut-back on downstream direction. It ranges from 0 to 400 units of 0.1 dB(physical values are 0 to 40 dB). Unit: tenth dB
C32 hwadslAtucChanPerfCurr15MinCrcBlks	1.3.6.1.2.1.10.94.1.1.10.1.65541	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel within the current 15 minute interval.
C32 hwadslAtucChanPerfCurr15MinFecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65539	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel within the current 15 minute interval.
C32 hwadslAtucChanPerfCurr15MinHecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65540	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel within the current 15 minute interval.
G32 hwadslAtucChanPerfCurr15MinRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65552	Gauge32	read-only	Count of units corrected by retransmission on this channel within the current 15 minute interval.
G32 hwadslAtucChanPerfCurr15MinRtxCW	1.3.6.1.2.1.10.94.1.1.10.1.65551	Gauge32	read-only	Count of units request retransmission on this channel within the current 15 minute interval.
G32 hwadslAtucChanPerfCurr15MinRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65553	Gauge32	read-only	Count of units uncorrected by retransmission on this channel within the current 15 minute interval.
C32 hwadslAtucChanPerfCurr1DayCrcBlks	1.3.6.1.2.1.10.94.1.1.10.1.65544	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
C32 hwadslAtucChanPerfCurr1DayFecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65542	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
C32 hwadslAtucChanPerfCurr1DayHecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65543	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
G32 hwadslAtucChanPerfCurr1DayRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65555	Gauge32	read-only	Count of units corrected by retransmission on this channel during the current day.
G32 hwadslAtucChanPerfCurr1DayRtxCW	1.3.6.1.2.1.10.94.1.1.10.1.65554	Gauge32	read-only	Count of units request retransmission on this channel during the current day.
G32 hwadslAtucChanPerfCurr1DayRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65556	Gauge32	read-only	Count of units uncorrected by retransmission on this channel during the current day.
C32 hwadslAtucChanPerfPrev1DayCrcBlks	1.3.6.1.2.1.10.94.1.1.10.1.65547	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel within the most recent previous 1-day period.
C32 hwadslAtucChanPerfPrev1DayFecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65545	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel within the most recent previous 1-day period.
C32 hwadslAtucChanPerfPrev1DayHecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65546	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel within the most recent previous 1-day period.
G32 hwadslAtucChanPerfPrev1DayRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65558	Gauge32	read-only	Count of units corrected by retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAtucChanPerfPrev1DayRtxCW	1.3.6.1.2.1.10.94.1.1.10.1.65557	Gauge32	read-only	Count of units request retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAtucChanPerfPrev1DayRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65559	Gauge32	read-only	Count of units uncorrected by retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAtucChanPhyRrrcBits	1.3.6.1.2.1.10.94.1.1.4.1.65541	Gauge32	read-only	The bits in the channel that used to retransmission on downstream direction.
G32 hwadslAtucChanPhyRtxQueue	1.3.6.1.2.1.10.94.1.1.4.1.65542	Gauge32	read-only	Queues in send buffer on downstream direction.
G32 hwadslAtucChanRsDepth	1.3.6.1.2.1.10.94.1.1.4.1.65539	Gauge32	read-only	Indicates Reed-Solomon depth on downstream direction. Unit: byte
G32 hwadslAtucChanRsRedundancy	1.3.6.1.2.1.10.94.1.1.4.1.65538	Gauge32	read-only	Indicates Reed-Solomon redundancy on downstream direction. Unit: byte
G32 hwadslAtucChanRsSize	1.3.6.1.2.1.10.94.1.1.4.1.65543	Gauge32	read-only	Indicates Reed-Solomon Codeword Size on downstream direction . Range: 0-255 Unit: byte
G32 hwadslAtucChanRsSymbols	1.3.6.1.2.1.10.94.1.1.4.1.65537	Gauge32	read-only	Indicates Reed-Solomon symbols on downstream direction. The value multiply 1/10000 is the real value. Unit: byte
G32 hwadslAtucChanRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65549	Gauge32	read-only	Count of units corrected by retransmission since agent reset.
G32 hwadslAtucChanRtxCW	1.3.6.1.2.1.10.94.1.1.10.1.65548	Gauge32	read-only	Count of units request retransmission since agent reset.
G32 hwadslAtucChanRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65550	Gauge32	read-only	Count of units uncorrected by retransmission since agent reset.
G32 hwadslAtucChanSymbolLength	1.3.6.1.2.1.10.94.1.1.4.1.65540	Gauge32	read-only	Indicates the Bit Number of the DMT Symbol on downstream direction. Unit: bit
INT hwAdslAtucConfDownBitSwap	1.3.6.1.2.1.10.94.1.1.14.1.65536	INTEGER	read-create	Enables and disables the down bitswap of a template. Options: 1. enabled(1) - Indicates that the downstream bit swap is enabled 2. disabled(2) - Indicates that the downstream bit swap is disabled Default: enabled(1)
INT hwAdslAtucConfUpBitSwap	1.3.6.1.2.1.10.94.1.1.14.1.65537	INTEGER	read-create	Enables and disables the up bitswap of a template. Options: 1. enabled(1) - Indicates that the upstream bit swap is enabled 2. disabled(2) - Indicates that the upstream bit swap is disabled Default: enabled(1)
G32 hwAdslAtucCurrAtn	1.3.6.1.2.1.10.94.1.1.65546.1.15	Gauge32	read-only	Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU. Range: 0-630 Unit: tenth dB
G32 hwAdslAtucCurrAttainableRate	1.3.6.1.2.1.10.94.1.1.65546.1.17	Gauge32	read-only	Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate. Unit: bps
G32 hwAdslAtucCurrSignalAtn	1.3.6.1.2.1.10.94.1.1.2.1.65537	Gauge32	read-only	Current signal attenuation of the ATU-C, indicating the difference between the transmit signal of the ATU-R and the receive signal of the ATU-C. Range: 0-630 Unit: tenth dB
I32 hwAdslAtucCurrSnrMgn	1.3.6.1.2.1.10.94.1.1.65546.1.16	Integer32	read-only	Noise Margin as seen by this ATU with respect to its received signal in tenth dB. Unit: tenth dB
HWA hwAdslAtucCurrTransMode	1.3.6.1.2.1.10.94.1.1.2.1.65536	HWADSLTRANSMISSIONMODETYPE	read-only	A set of ADSL line transmission modes.
NUM hwAdslAtucIntervalESs	1.3.6.1.2.1.10.94.1.1.65546.1.23	PerfIntervalCount	read-only	Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects. Unit: seconds
C32 hwAdslAtucIntervalFailFullInits	1.3.6.1.2.1.10.94.1.1.8.1.65535	Counter32	read-only	Count of the line initialization failed attempts during the interval.
NUM hwAdslAtucIntervalLofs	1.3.6.1.2.1.10.94.1.1.65546.1.24	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Framing. Unit: seconds
NUM hwAdslAtucIntervalLols	1.3.6.1.2.1.10.94.1.1.65546.1.25	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Link. Unit: seconds
NUM hwAdslAtucIntervalLoss	1.3.6.1.2.1.10.94.1.1.65546.1.26	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Signal. Unit: seconds
NUM hwAdslAtucIntervalLprs	1.3.6.1.2.1.10.94.1.1.65546.1.27	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Power. Unit: seconds
NUM hwAdslAtucIntervalSesL	1.3.6.1.2.1.10.94.1.1.65546.1.40	PerfIntervalCount	read-only	For the each interval, adslAtucIntervalSesL reports the number of seconds during which there have been severely errored seconds-line. Unit: seconds
NUM hwAdslAtucIntervalUasL	1.3.6.1.2.1.10.94.1.1.65546.1.41	PerfIntervalCount	read-only	For the each interval, adslAtucIntervalUasL reports the number of seconds during which there have been unavailable seconds-line. Unit: seconds
G32 hwAdslAtucLatestAtn	1.3.6.1.2.1.10.94.1.1.65544.1.7	Gauge32	read-only	Measured difference in the total power transmitted as seen by this ATU-C at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
G32 hwAdslAtucLatestAttainableRate	1.3.6.1.2.1.10.94.1.1.65544.1.9	Gauge32	read-only	Indicates the maximum attainable data rate by the ATU-C at the time of the last adslAtucRateChangeTrap event. Unit: bps
G32 hwAdslAtucLatestConfTxRate	1.3.6.1.2.1.10.94.1.1.65544.1.11	Gauge32	read-only	Configured transmit rate for ADSL port, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates. Unit: bps
G32 hwAdslAtucLatestInterleaveDelay	1.3.6.1.2.1.10.94.1.1.65544.1.13	Gauge32	read-only	Interleave Delay for this channel when latest actived. Unit: milliseconds
I32 hwAdslAtucLatestSnrMgn	1.3.6.1.2.1.10.94.1.1.65544.1.5	Integer32	read-only	Noise Margin as seen by this ATU-C at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
I32 hwAdslAtucLatestTargetSnrMgn	1.3.6.1.2.1.10.94.1.1.65544.1.15	Integer32	read-only	Port Signal/Noise Margin. Range: 0-310 Unit: tenth dB
G32 hwAdslAtucLatestTxRate	1.3.6.1.2.1.10.94.1.1.65544.1.3	Gauge32	read-only	Actual transmit rate on this channel when latest actived. Unit: bps
G32 hwAdslAtucLatestTxRateThreshold	1.3.6.1.2.1.10.94.1.1.65544.1.17	Gauge32	read-only	Port down stream threshold. Unit: bps
C32 hwAdslAtucPerfCurr15MinFailFullInits	1.3.6.1.2.1.10.94.1.1.6.1.65536	Counter32	read-only	Count of the line initialization failed attempts in the current 15 minute interval.
C32 hwAdslAtucPerfCurr1DayFailFullInits	1.3.6.1.2.1.10.94.1.1.6.1.65537	Counter32	read-only	Count of the line initialization failed attempts in the day as measured by adslAtucPerfCurr1DayTimeElapsed.
C32 hwAdslAtucPerfFailFullInits	1.3.6.1.2.1.10.94.1.1.6.1.65535	Counter32	read-only	Count of the line initialization failed attempts since agent reset.
C32 hwAdslAtucPerfPrev1DayFailFullInits	1.3.6.1.2.1.10.94.1.1.6.1.65538	Counter32	read-only	Count of the line initialization failed attempts in the most recent previous 1-day period.
G32 hwAdslAtucPreAtn	1.3.6.1.2.1.10.94.1.1.65539.1.5	Gauge32	read-only	Measured difference in the total power transmitted as seen by this ATU-C at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
U32 hwAdslAtucPrevAttainableRate	1.3.6.1.2.1.10.94.1.1.65539.1.3	Unsigned32	read-only	Indicates the maximum attainable data rate by the ATU-C at the time of the last adslAtucRateChangeTrap event. Unit: bps
I32 hwAdslAtucPrevSnrMgn	1.3.6.1.2.1.10.94.1.1.65539.1.1	Integer32	read-only	Noise Margin as seen by this ATU-C at the time of the last adslAtucRateChangeTrap event. Unit: tenth dB
G32 hwadslAturChanCodeGain	1.3.6.1.2.1.10.94.1.1.5.1.65544	Gauge32	read-only	Indicates Code Gain on upstream direction. It ranges from 0 to 16 units of 0.5 dB (physical values are 0 to 8 dB).
C32 hwadslAturChanCrcBlks	1.3.6.1.2.1.10.94.1.1.11.1.65538	Counter32	read-only	Count of all blocks received with CRC anomalies since agent reset.
G32 hwadslAturChanCurrINP	1.3.6.1.2.1.10.94.1.1.5.1.65536	Gauge32	read-only	Indicates Impulse Noise Protection on upstream direction. The value multiply 1/10000 is the real value. Unit: DMT Symbol
G32 hwAdslAturChanCurrTxRate	1.3.6.1.2.1.10.94.1.1.65546.1.22	Gauge32	read-only	Actual transmit rate on this channel. Unit: bps
C32 hwadslAturChanFecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65536	Counter32	read-only	Count of all blocks received with FEC anomalies since agent reset.
C32 hwadslAturChanHecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65537	Counter32	read-only	Count of all blocks received with HEC anomalies since agent reset.
NUM hwAdslAturChanIntervalCorrectedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.38	PerfIntervalCount	read-only	Count of all blocks received with errors that were corrected on this channel during this interval.
NUM hwadslAturChanIntervalCrcBlks	1.3.6.1.2.1.10.94.1.1.13.1.65538	PerfIntervalCount	read-only	Count of all blocks received with CRC anomalies on this channel during this interval.
NUM hwadslAturChanIntervalFecBlks	1.3.6.1.2.1.10.94.1.1.13.1.65536	PerfIntervalCount	read-only	Count of all blocks received with FRC anomalies on this channel during this interval.
NUM hwadslAturChanIntervalHecBlks	1.3.6.1.2.1.10.94.1.1.13.1.65537	PerfIntervalCount	read-only	Count of all blocks received with HRC anomalies on this channel during this interval.
NUM hwAdslAturChanIntervalReceivedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.36	PerfIntervalCount	read-only	Count of all encoded blocks received on this channel during this interval.
G32 hwadslAturChanIntervalRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.13.1.65540	Gauge32	read-only	Count of units corrected by retransmission on this channel during this interval.
G32 hwadslAturChanIntervalRtxCW	1.3.6.1.2.1.10.94.1.1.13.1.65539	Gauge32	read-only	Count of units request retransmission on this channel during this interval.
G32 hwadslAturChanIntervalRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.13.1.65541	Gauge32	read-only	Count of units uncorrected by retransmission on this channel during this interval.
NUM hwAdslAturChanIntervalTransmittedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.37	PerfIntervalCount	read-only	Count of all encoded blocks transmitted on this channel during this interval.
NUM hwAdslAturChanIntervalUncorrectBlks	1.3.6.1.2.1.10.94.1.1.65546.1.39	PerfIntervalCount	read-only	Count of all blocks received with uncorrectable errors on this channel during this interval.
C32 hwadslAturChanPerfCurr15MinCrcBlks	1.3.6.1.2.1.10.94.1.1.11.1.65541	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel within the current 15 minute interval.
C32 hwadslAturChanPerfCurr15MinFecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65539	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel within the current 15 minute interval.
C32 hwadslAturChanPerfCurr15MinHecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65540	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel within the current 15 minute interval.
G32 hwadslAturChanPerfCurr15MinRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65552	Gauge32	read-only	Count of units corrected by retransmission on this channel within the current 15 minute interval.
G32 hwadslAturChanPerfCurr15MinRtxCW	1.3.6.1.2.1.10.94.1.1.11.1.65551	Gauge32	read-only	Count of units request retransmission on this channel within the current 15 minute interval.
G32 hwadslAturChanPerfCurr15MinRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65553	Gauge32	read-only	Count of units uncorrected by retransmission on this channel within the current 15 minute interval.
C32 hwadslAturChanPerfCurr1DayCrcBlks	1.3.6.1.2.1.10.94.1.1.11.1.65544	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
C32 hwadslAturChanPerfCurr1DayFecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65542	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
C32 hwadslAturChanPerfCurr1DayHecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65543	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
G32 hwadslAturChanPerfCurr1DayRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65555	Gauge32	read-only	Count of units corrected by retransmission on this channel during the current day.
G32 hwadslAturChanPerfCurr1DayRtxCW	1.3.6.1.2.1.10.94.1.1.11.1.65554	Gauge32	read-only	Count of units request retransmission on this channel during the current day.
G32 hwadslAturChanPerfCurr1DayRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65556	Gauge32	read-only	Count of units uncorrected by retransmission on this channel during the current day.
C32 hwadslAturChanPerfPrev1DayCrcBlks	1.3.6.1.2.1.10.94.1.1.11.1.65547	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel within the most recent previous 1-day period.
C32 hwadslAturChanPerfPrev1DayFecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65545	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel within the most recent previous 1-day period.
C32 hwadslAturChanPerfPrev1DayHecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65546	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel within the most recent previous 1-day period.
G32 hwadslAturChanPerfPrev1DayRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65558	Gauge32	read-only	Count of units corrected by retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAturChanPerfPrev1DayRtxCW	1.3.6.1.2.1.10.94.1.1.11.1.65557	Gauge32	read-only	Count of units request retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAturChanPerfPrev1DayRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65559	Gauge32	read-only	Count of units uncorrected by retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAturChanPhyRrrcBits	1.3.6.1.2.1.10.94.1.1.5.1.65541	Gauge32	read-only	The bits in the channel that used to retransmission on upstream direction.
G32 hwadslAturChanPhyRtxQueue	1.3.6.1.2.1.10.94.1.1.5.1.65542	Gauge32	read-only	Queues in send buffer on upstream direction.
G32 hwadslAturChanRsDepth	1.3.6.1.2.1.10.94.1.1.5.1.65539	Gauge32	read-only	Indicates Reed-Solomon depth on upstream direction. Unit: byte
G32 hwadslAturChanRsRedundancy	1.3.6.1.2.1.10.94.1.1.5.1.65538	Gauge32	read-only	Indicates Reed-Solomon redundancy on upstream direction. Unit: byte
G32 hwadslAturChanRsSize	1.3.6.1.2.1.10.94.1.1.5.1.65543	Gauge32	read-only	Indicates Reed-Solomon Codeword Size on upstream direction. Range: 0-255 Unit: byte
G32 hwadslAturChanRsSymbols	1.3.6.1.2.1.10.94.1.1.5.1.65537	Gauge32	read-only	Indicates Reed-Solomon symbols on upstream direction. The value multiply 1/10000 is the real value. Unit: byte
G32 hwadslAturChanRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65549	Gauge32	read-only	Count of units corrected by retransmission since agent reset.
G32 hwadslAturChanRtxCW	1.3.6.1.2.1.10.94.1.1.11.1.65548	Gauge32	read-only	Count of units request retransmission since agent reset.
G32 hwadslAturChanRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65550	Gauge32	read-only	Count of units uncorrected by retransmission since agent reset.
G32 hwadslAturChanSymbolLength	1.3.6.1.2.1.10.94.1.1.5.1.65540	Gauge32	read-only	Indicates the Bit Number of the DMT Symbol on upstream direction. Unit: bit
G32 hwAdslAturCurrAtn	1.3.6.1.2.1.10.94.1.1.65546.1.19	Gauge32	read-only	Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU. Range: 0-630 Unit: tenth dB
G32 hwAdslAturCurrAttainableRate	1.3.6.1.2.1.10.94.1.1.65546.1.21	Gauge32	read-only	Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate. Unit: bps
G32 hwAdslAturCurrSignalAtn	1.3.6.1.2.1.10.94.1.1.3.1.65536	Gauge32	read-only	The signal attenuation value on ATUR: It indicates the difference between the transmit signal of the ATU-C and the receive signal of the ATU-R. Range: 0-630 Unit: tenth dB
I32 hwAdslAturCurrSnrMgn	1.3.6.1.2.1.10.94.1.1.65546.1.20	Integer32	read-only	Noise Margin as seen by this ATU with respect to its received signal in tenth dB. Unit: tenth dB
NUM hwAdslAturIntervalESs	1.3.6.1.2.1.10.94.1.1.65546.1.28	PerfIntervalCount	read-only	Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects. Unit: seconds
NUM hwAdslAturIntervalLofs	1.3.6.1.2.1.10.94.1.1.65546.1.29	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Framing. Unit: seconds
NUM hwAdslAturIntervalLoss	1.3.6.1.2.1.10.94.1.1.65546.1.30	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Signal. Unit: seconds
NUM hwAdslAturIntervalLprs	1.3.6.1.2.1.10.94.1.1.65546.1.31	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Power. Unit: seconds
NUM hwAdslAturIntervalSesL	1.3.6.1.2.1.10.94.1.1.65546.1.42	PerfIntervalCount	read-only	For the each interval, adslAturIntervalSesL reports the number of seconds during which there have been severely errored seconds-line. Unit: seconds
NUM hwAdslAturIntervalUasL	1.3.6.1.2.1.10.94.1.1.65546.1.43	PerfIntervalCount	read-only	For the each interval, adslAturIntervalUasL reports the number of seconds during which there have been unavailable seconds-line. Unit: seconds
G32 hwAdslAturLatestAtn	1.3.6.1.2.1.10.94.1.1.65544.1.8	Gauge32	read-only	Measured difference in the total power transmitted as seen by this ATU-R at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
G32 hwAdslAturLatestAttainableRate	1.3.6.1.2.1.10.94.1.1.65544.1.10	Gauge32	read-only	Indicates the maximum attainable data rate by the ATU-R at the time of the last adslAtucRateChangeTrap event. Unit: bps
G32 hwAdslAturLatestConfTxRate	1.3.6.1.2.1.10.94.1.1.65544.1.12	Gauge32	read-only	Configured receive rate for ADSL port, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates. Unit: bps
G32 hwAdslAturLatestInterleaveDelay	1.3.6.1.2.1.10.94.1.1.65544.1.14	Gauge32	read-only	Interleave Delay for this channel when latest actived. Unit: milliseconds
I32 hwAdslAturLatestSnrMgn	1.3.6.1.2.1.10.94.1.1.65544.1.6	Integer32	read-only	Noise Margin as seen by this ATU-R at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
I32 hwAdslAturLatestTargetSnrMgn	1.3.6.1.2.1.10.94.1.1.65544.1.16	Integer32	read-only	Port Signal/Noise Margin. Range: 0-310 Unit: tenth dB
G32 hwAdslAturLatestTxRate	1.3.6.1.2.1.10.94.1.1.65544.1.4	Gauge32	read-only	Actual transmit rate on this channel when latest actived. Unit: bps
G32 hwAdslAturLatestTxRateThreshold	1.3.6.1.2.1.10.94.1.1.65544.1.18	Gauge32	read-only	Port up stream threshold. Unit: bps
G32 hwAdslAturPreAtn	1.3.6.1.2.1.10.94.1.1.65539.1.6	Gauge32	read-only	Measured difference in the total power transmitted as seen by this ATU-R at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
U32 hwAdslAturPrevAttainableRate	1.3.6.1.2.1.10.94.1.1.65539.1.4	Unsigned32	read-only	Indicates the maximum attainable data rate by the ATU-R at the time of the last adslAtucRateChangeTrap event. Unit: bps
I32 hwAdslAturPrevSnrMgn	1.3.6.1.2.1.10.94.1.1.65539.1.2	Integer32	read-only	Noise Margin as seen by this ATU-R at the time of the last adslAtucRateChangeTrap event. Unit: tenth dB
ADS hwadslAturTransmissionCapabilities	1.3.6.1.2.1.10.94.1.1.3.1.65535	Adsl2TransmissionModeType	read-only	The ATU transmission system capability list of the different coding types. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the ATU supports the respective coding. The value may be derived from the handshaking procedures defined in G.994.1.
ADS hwadslExtDsINPmax	1.3.6.1.2.1.10.94.1.1.65543.1.36	Adsl2SymbolProtection	read-write	Maximum Impulse Noise Protection on downstream direction. The parameter can take the following values: noProtection(1), halfSymbol(2), singleSymbol(3), twoSymbols(4), threeSymbols(5), fourSymbols(6), fiveSymbols(7), sixSymbols(8), sevenSymbols(9), eightSymbols(10), nineSymbols(11), tenSymbols(12), elevenSymbols(13), twelveSymbols(14), thirteeSymbols(15), fourteenSymbols(16), fifteenSymbols(17), sixteenSymbols(18) The value multiply 1/2 is the real value of Noise Protection values. Unit: DMT Symbol
I32 hwAdslExtDsMaxPsd	1.3.6.1.2.1.10.94.1.1.65543.1.18	Integer32	read-create	Maximum PSD margin in downstream.
I32 hwadslExtDsMinRSoverhead	1.3.6.1.2.1.10.94.1.1.65543.1.38	Integer32	read-write	The minimum value of R/N on downstream direction. Range: 0-128 Default: 0 Unit: 1/256
I32 hwadslExtDsMinRtxRatio	1.3.6.1.2.1.10.94.1.1.65543.1.37	Integer32	read-write	Minimum rtxratio on downstream direction. Range: 0-255 Default: 0 Unit: 1/256
I32 hwAdslExtDsMinTrainSnrMgn	1.3.6.1.2.1.10.94.1.1.65543.1.16	Integer32	read-create	Maximum Trainning Margin in downstream. Range: 0-310 Default: 30 Unit: tenth dB
INT hwadslExtDsPhyRcontrol	1.3.6.1.2.1.10.94.1.1.65543.1.35	INTEGER	read-write	To enable or disable the PHY-R function on downstream direction. Options: 1. enable(1) - The PHY-R function on downstream direction is enabled 2. disable(2) - The PHY-R function on downstream direction is disabled Default: disable(2)
ADS hwadslExtUsINPmax	1.3.6.1.2.1.10.94.1.1.65543.1.32	Adsl2SymbolProtection	read-write	Maximum Impulse Noise Protection on upstream direction. The parameter can take the following values: noProtection(1), halfSymbol(2), singleSymbol(3), twoSymbols(4), threeSymbols(5), fourSymbols(6), fiveSymbols(7), sixSymbols(8), sevenSymbols(9), eightSymbols(10), nineSymbols(11), tenSymbols(12), elevenSymbols(13), twelveSymbols(14), thirteeSymbols(15), fourteenSymbols(16), fifteenSymbols(17), sixteenSymbols(18) The value multiply 1/2 is the real value of Noise Protection values. Unit: DMT Symbol Default: 1
I32 hwadslExtUsMinRSoverhead	1.3.6.1.2.1.10.94.1.1.65543.1.34	Integer32	read-write	The minimum value of R/N on upstream direction. Range: 0-128 Default: 0 Unit: 1/256
I32 hwadslExtUsMinRtxRatio	1.3.6.1.2.1.10.94.1.1.65543.1.33	Integer32	read-write	Minimum rtxratio on upstream direction. Range: 0-255 Default: 0 Unit: 1/256
I32 hwAdslExtUsMinTrainSnrMgn	1.3.6.1.2.1.10.94.1.1.65543.1.17	Integer32	read-create	Maximum Trainning Margin in upstream. Range: 0-310 Default: 30 Unit: tenth dB
INT hwadslExtUsPhyRcontrol	1.3.6.1.2.1.10.94.1.1.65543.1.31	INTEGER	read-write	To enable or disable the PHY-R function on upstream direction. Options: 1. enable(1) - The PHY-R function on upstream direction is enabled 2. disable(2) - The PHY-R function on upstream direction is disabled Default: disable(2)
hwAdslGeneralTraps	1.3.6.1.2.1.10.94.1.2.65536.1
hwAdslGeneralTrapsOIDs	1.3.6.1.2.1.10.94.1.2.65536.1.0
INT hwadslLConfProfAdslMode	1.3.6.1.2.1.10.94.1.1.65543.1.40	INTEGER	read-write	The ADSL2 management model specified includes an ADSL Mode attribute which identifies an instance of ADSL Mode-Specific PSD Configuration object in the ADSL Line Profile. The following classes of ADSL operating mode are defined. Options: 1. defMode(1) - ADSL transmit mode is defMode 2. adsl(2) - ADSL transmit mode is adsl 3. adsl2Pots(3) - ADSL transmit mode is adsl2Pots 4. adsl2Isdn(4) - ADSL transmit mode is adsl2Isdn 5. adsl2PlusPots(5) - ADSL transmit mode is adsl2PlusPots 6. adsl2PlusIsdn(6) - ADSL transmit mode is adsl2PlusIsdn 7. adsl2ReachExtended(7) - ADSL transmit mode is adsl2ReachExtended 8. invalidValue(-1) - Invalid value
INT hwadslLineAlarmConfProfileDyingGasp	1.3.6.1.2.1.10.94.1.1.15.1.65536	INTEGER	read-create	This object enables/disables the report of LOSS-OF-POWER alarm in an ADSL line, This object is defaulted enable(1). Options: 1. enable (1) - The LOSS-OF-POWER alarm in an ADSL line will be reported 2. disable (2) - The LOSS-OF-POWER alarm in an ADSL line will not be reported
hwAdslLineBitAllocationEntry	1.3.6.1.2.1.10.94.1.1.65537.1		not-accessible	The hwAdslLineBitAllocationTable contains the detailed bit-allocation information for the current link. This information can be used to determine whether a given sub-carrier loop has sufficient margin to support ADSL data rates, and possibly to determine whether certain specific types of interfe- rence or line attenuation exist.The bit allocation information are only va- lid when the ATU-C is in the C-ACTIVE state. The index of this entry is ifIndex.
hwAdslLineBitAllocationTable	1.3.6.1.2.1.10.94.1.1.65537		not-accessible	The hwAdslLineBitAllocationTable contains the detailed bit-allocation information for the current link. This information can be used to determine whether a given sub-carrier loop has sufficient margin to support ADSL data rates, and possibly to determine whether certain specific types of interfe- rence or line attenuation exist.The bit allocation information are only va- lid when the ATU-C is in the C-ACTIVE state. The index of this table is ifIndex.
OCT hwAdslLineConfProfile	1.3.6.1.2.1.10.94.1.1.65546.1.13	OCTET STRING	read-only	The value of this object identifies the row in the ADSL Line Configuration Profile Table, (adslLineConfProfileTable), which applies for this ADSL line, and channels if applicable. For 'dynamic' mode, in the case which the configuration profile has not been set, the value will be set to 'DEFVAL'. If the creator of this MIB has chosen not to implement 'dynamic assignment' of profiles, this object's MIN-ACCESS is read-only.
I32 hwadslLineDisableToneSection1Begin	1.3.6.1.2.1.10.94.1.1.65543.1.2	Integer32	read-create	The begin index of section1. Range: 0-511
I32 hwadslLineDisableToneSection1End	1.3.6.1.2.1.10.94.1.1.65543.1.3	Integer32	read-create	The end index of section1. Range: 0-511
INT hwadslLineDisableToneSection1Flag	1.3.6.1.2.1.10.94.1.1.65543.1.4	INTEGER	read-create	The enable flag of section1. Options: 1. enabled(1) - The first tone section is enabled 2. disabled(2) - The first tone section is disabled
I32 hwadslLineDisableToneSection2Begin	1.3.6.1.2.1.10.94.1.1.65543.1.5	Integer32	read-create	The begin index of section2. Range: 0-511
I32 hwadslLineDisableToneSection2End	1.3.6.1.2.1.10.94.1.1.65543.1.6	Integer32	read-create	The end index of section2. Range: 0-511
INT hwadslLineDisableToneSection2Flag	1.3.6.1.2.1.10.94.1.1.65543.1.7	INTEGER	read-create	The enable flag of section2. Options: 1. enabled(1) - The second tone section is enabled 2. disabled(2) - The second tone section is disabled
I32 hwadslLineDisableToneSection3Begin	1.3.6.1.2.1.10.94.1.1.65543.1.8	Integer32	read-create	The begin index of section3. Range: 0-511
I32 hwadslLineDisableToneSection3End	1.3.6.1.2.1.10.94.1.1.65543.1.9	Integer32	read-create	The end index of section3. Range: 0-511
INT hwadslLineDisableToneSection3Flag	1.3.6.1.2.1.10.94.1.1.65543.1.10	INTEGER	read-create	The enable flag of the third section. Options: 1. enabled(1) - The third tone section is enabled 2. disabled(2) - The third tone section is disabled
I32 hwadslLineDisableToneSection4Begin	1.3.6.1.2.1.10.94.1.1.65543.1.11	Integer32	read-create	The begin index of the fourth section. Range: 0-511
I32 hwadslLineDisableToneSection4End	1.3.6.1.2.1.10.94.1.1.65543.1.12	Integer32	read-create	The end index of the fourth section. Range: 0-511
INT hwadslLineDisableToneSection4Flag	1.3.6.1.2.1.10.94.1.1.65543.1.13	INTEGER	read-create	The enable flag of the fourth section. Range: 0-511 Options: 1. enabled(1) - The fourth tone section is enabled 2. disabled(2) - The fourth tone section is disabled
OCT hwAdslLineDownStreamBitAllocHigh	1.3.6.1.2.1.10.94.1.1.65537.1.4	OCTET STRING	read-only	when used to Adsl board This object contains the second 128 downstream sub-carrier bit allocations (sub-carrier # 129-256). This object is 64 bytes in length, where each byte contains 2 sub-carrier values. Byte 1 - 64 Downstream bit allocation (second 128 sub-carriers), one byte for two sub-carriers. 1 Bits 4 - 7 # bits in 129th downstream sub-carrier 1 Bits 0 - 3 # bits in 130th downstream sub-carrier ... 64 Bits 4 - 7 # bits in 255th downstream sub-carrier 64 Bits 0 - 3 # bits in 256th downstream sub-carrier when used to Adsl2+ board This object contains the second 256 downstream sub-carrier bit allocations (sub-carrier # 257-512). This object is 256 bytes in length, where each byte contains 1 sub-carrier values. Byte 1 - 256 Downstream bit allocation (second 256 sub-carriers), one byte for one sub-carriers. 1 Bits 0 - 7 # bits in 1st downstream sub-carrier ... 255 Bits 0 - 7 # bits in 255th downstream sub-carrier 256 Bits 0 - 7 # bits in 256th downstream sub-carrier
OCT hwAdslLineDownStreamBitAllocLow	1.3.6.1.2.1.10.94.1.1.65537.1.3	OCTET STRING	read-only	when used to Adsl board This object contains the first 128 downstream sub-carrier bit allocations (sub-carrier # 1-128). This object is 64 bytes in length, where each byte contains 2 sub-carrier values. Byte 1 - 64 Downstream bit allocation (first 128 sub-carriers), one byte for two sub-carriers. 1 Bits 4 - 7 # bits in 1st downstream sub-carrier 1 Bits 0 - 3 # bits in 2nd downstream sub-carrier ... 64 Bits 4 - 7 # bits in 127th downstream sub-carrier 64 Bits 0 - 3 # bits in 128th downstream sub-carrier when used to Adsl2+ board This object contains the first 256 downstream sub-carrier bit allocations (sub-carrier # 1-256). This object is 256 bytes in length, where each byte contains 1 sub-carrier values. Byte 1 - 256 Downstream bit allocation (first 256 sub-carriers), one byte for one sub-carriers. 1 Bits 0 - 7 # bits in 1st downstream sub-carrier ... 255 Bits 0 - 7 # bits in 255th downstream sub-carrier 256 Bits 0 - 7 # bits in 256th downstream sub-carrier
I32 hwAdslLineDownStreamBitsPerFrame	1.3.6.1.2.1.10.94.1.1.65537.1.1	Integer32	read-only	Number of bits required per frame in the downstream data path for the current configuration.
OCT hwadslLineDynamicProfile	1.3.6.1.2.1.10.94.1.1.1.1.65537	OCTET STRING	read-write	The value of this object identifies the row in the ADSL Dynamic Profile Table,which applies to this ADSL line, and channels if applicable. NULL - indicates that there is no Dynamic profile bound to this port. Range: 0-32
OCT hwadslLineExtConfProfile	1.3.6.1.2.1.10.94.1.1.1.1.65536	OCTET STRING	read-write	The value of this object identifies the row in the ADSL Extend Line Configuration Profile Table, (adslLineExtConfProfileTable), which applies to this ADSL line, and channels if applicable. NULL - indicates that there is no extend line profile bound to this port. Range: 0-32
hwadslLineExtConfProfileEntry	1.3.6.1.2.1.10.94.1.1.65543.1		not-accessible	This table contains information on the ADSL extend line configuration. One entry in this table reflects a extend line profile defined by a manager which can be used to configure the ADSL line. The index of this entry is hwadslLineExtConfProfileName.
OCT hwadslLineExtConfProfileName	1.3.6.1.2.1.10.94.1.1.65543.1.1	OCTET STRING	not-accessible	This object is used by the hwadslLineExtConfProfileTable in order to identify a row of this table. This object indicates the name of the extended line profile.
ROW hwadslLineExtConfProfileRowStatus	1.3.6.1.2.1.10.94.1.1.65543.1.65535	RowStatus	read-create	This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to 'destroy' or 'outOfService') it must be first unreferenced from all associated lines. If the creator of this MIB has chosen not to implement 'dynamic assignment' of profiles, this object's MIN-ACCESS is read-only and its value is always to be 'active'.
hwadslLineExtConfProfileTable	1.3.6.1.2.1.10.94.1.1.65543		not-accessible	This table contains information on the ADSL extend line configuration. One entry in this table reflects a extend line profile defined by a manager which can be used to configure the ADSL line. The index of this table is hwadslLineExtConfProfileName.
DAT hwAdslLineLatestActiveTime	1.3.6.1.2.1.10.94.1.1.65544.1.1	DateAndTime	read-only	Actual time when latest actived.
hwAdslLineLatestActParaEntry	1.3.6.1.2.1.10.94.1.1.65544.1		not-accessible	This table provides one row for each ADSL PORT. Each row contains the latest actived Parameters. The index of this entry is ifIndex.
hwAdslLineLatestActParaTable	1.3.6.1.2.1.10.94.1.1.65544		not-accessible	This table provides one row for each ADSL PORT. Each row contains the latest actived Parameters. The index of this table is ifIndex.
DAT hwAdslLineLatestDeactiveTime	1.3.6.1.2.1.10.94.1.1.65544.1.2	DateAndTime	read-only	Actual time when latest deactived. If port is actived, the value is invalid.
hwAdslLinePreActParaEntry	1.3.6.1.2.1.10.94.1.1.65539.1		not-accessible	This table provides one row for each ADSL PORT. Each row contains the preactived Parameters. The index of this entry is ifIndex.
hwAdslLinePreActParaTable	1.3.6.1.2.1.10.94.1.1.65539		not-accessible	This table provides one row for each ADSL PORT. Each row contains the preactived Parameters. The index of this table is ifIndex.
INT hwAdslLinePvcConnectType	1.3.6.1.2.1.10.94.1.1.65536.1.10	INTEGER	read-only	The Connected type of the adsl line PVC. Options: 1. auto(0) - The Connected type of the adsl line PVC is auto 2. llc1483B(1) - The Connected type of the adsl line PVC is llc1483B 3. pppoaLLC(2) - The Connected type of the adsl line PVC is pppoaLLC 4. pppoaVcmux(3) - The Connected type of the adsl line PVC is pppoaVcmux 5. ipoaLLc(4) - The Connected type of the adsl line PVC is ipoaLLc 6. ipoaVcmux(5) - The Connected type of the adsl line PVC is ipoaVcmux
I32 hwAdslLinePvcDsBand	1.3.6.1.2.1.10.94.1.1.65536.1.5	Integer32	read-write	The down stream band of the adsl line PVC. Range: 0-450
hwAdslLinePvcEntry	1.3.6.1.2.1.10.94.1.1.65536.1		not-accessible	PVC configuration table of the ADSL port and used to configure the VPI and VCI of the ADSL port. The indexes of this entry are ifIndex,hwAdsllinePvcVpi,and hwAdsllinePvcVci. This table is used to configure only the CO PVC.
INT hwAdslLinePvcIGMPEnable	1.3.6.1.2.1.10.94.1.1.65536.1.8	INTEGER	read-write	This object allows the adsl line PVC to support IGMP. Options: 1. enable(1) - Indicates that the PVC of the ADSL port is enabled to support IGMP 2. disable(2) - Indicates that the PVC of the ADSL port is disabled to support IGMP Default: disable(2)
I32 hwAdslLinePvcIndex	1.3.6.1.2.1.10.94.1.1.65536.1.9	Integer32	read-write	The index of the adsl line PVC. Range: 1-8
INT hwAdslLinePvcMCastEnable	1.3.6.1.2.1.10.94.1.1.65536.1.7	INTEGER	read-write	This object allows the adsl line PVC to support multicast. Options: 1. enable(1) - Indicates that the PVC of the ADSL port is enabled to support the multicast 2. disable(2) - Indicates that the PVC of the ADSL port is disabled to support the multicast Default: disable(2)
I32 hwAdslLinePvcPriority	1.3.6.1.2.1.10.94.1.1.65536.1.4	Integer32	read-write	The Priority value of the adsl line PVC. Range: 0-7
ROW hwAdslLinePvcRowStatus	1.3.6.1.2.1.10.94.1.1.65536.1.11	RowStatus	read-create	Row status. Add or delete a table item.
hwAdslLinePvcTable	1.3.6.1.2.1.10.94.1.1.65536		not-accessible	PVC configuration table of the ADSL port and used to configure the VPI and VCI of the ADSL port. The indexes of this table are ifIndex,hwAdsllinePvcVpi,and hwAdsllinePvcVci. This table is used to configure only the CO PVC.
I32 hwAdslLinePvcUsBand	1.3.6.1.2.1.10.94.1.1.65536.1.6	Integer32	read-write	The up stream band of the adsl line PVC. Range: 0-450
I32 hwAdslLinePvcVci	1.3.6.1.2.1.10.94.1.1.65536.1.2	Integer32	read-only	The VCI of the adsl line.
I32 hwAdslLinePvcVlanId	1.3.6.1.2.1.10.94.1.1.65536.1.3	Integer32	read-write	The VLAN ID of the adsl line PVC. Range: 1-4000
I32 hwAdsllinePvcVpi	1.3.6.1.2.1.10.94.1.1.65536.1.1	Integer32	read-only	The VPI of the adsl line.
OCT hwAdslLineUpStreamBitAlloc	1.3.6.1.2.1.10.94.1.1.65537.1.5	OCTET STRING	read-only	when used to Adsl board This Object contains 64 upstream sub-carrier bit allocations (sub-carrier # 1-64). This Object is 32 bytes in length, where each byte contains 2 sub-carrier values. Byte 1-32 Upstream bit allocation information, total: 32 bytes, one byte for two sub-carriers. 1 Bits 7 - 4 # bits in 1st upstream sub-carrier 1 Bits 3 - 0 # bits in 2nd upstream sub-carrier ... 32 Bits 7 - 4 # bits in 63rd upstream sub-carrier 32 Bits 3 - 0 # bits in 64th upstream sub-carrier when used to Adsl2+ board This Object contains 64 upstream sub-carrier bit allocations (sub-carrier # 1-64). This Object is 64 bytes in length, where each byte contains 1 sub-carrier values. Byte 1-64 Upstream bit allocation information, total: 64 bytes, one byte for one sub-carriers. 1 Bits 7 - 0 # bits in 1st upstream sub-carrier ... 64 Bits 7 - 0 # bits in 64th upstream sub-carrier
I32 hwAdslLineUpStreamBitsPerFrame	1.3.6.1.2.1.10.94.1.1.65537.1.2	Integer32	read-only	Number of bits required per frame in the upstream data path for the current configuration.
C32 hwAdslPort15minUpTime	1.3.6.1.2.1.10.94.1.1.65546.1.14	Counter32	read-only	Up time in the interval. Unit: seconds
C32 hwAdslPort15minutesPerformanceInBytes	1.3.6.1.2.1.10.94.1.1.65546.1.2	Counter32	read-only	Read the receive bytes of xDSL port during 15 minutes.
I32 hwAdslPort15minutesPerformanceInterval	1.3.6.1.2.1.10.94.1.1.65546.1.1	Integer32	not-accessible	The index of the interval which is queried. Range: 0-96
C32 hwAdslPort15minutesPerformanceOutBytes	1.3.6.1.2.1.10.94.1.1.65546.1.3	Counter32	read-only	Read the transmit bytes of xDSL port during 15 minutes.
NTF hwAdslPortActRateMonitorTrap	1.3.6.1.2.1.10.94.1.2.65536.1.0.1			Definition of the trap reported when the ADSL port rate fails to meet the requirement. If ADSL act rate is lower than threshold, hwTrapType is 1. Otherwise, hwTrapType is 2.
C32 hwAdslPortAtucCodeViolation	1.3.6.1.2.1.10.94.1.1.65546.1.6	Counter32	read-only	Seconds of head errors of the ATUC cell within 15 minutes.
C32 hwAdslPortAtucFecSeconds	1.3.6.1.2.1.10.94.1.1.65546.1.8	Counter32	read-only	Seconds of the ATUC FEC errors within 15 minutes.
C32 hwAdslPortAtucHecDropCellsCnt	1.3.6.1.2.1.10.94.1.1.65546.1.11	Counter32	read-only	ATUC cells discarded with HEC Errors.
C32 hwAdslPortAturCodeViolation	1.3.6.1.2.1.10.94.1.1.65546.1.7	Counter32	read-only	Seconds of head errors of the ATUC cell within 15 minutes.
C32 hwAdslPortAturFecSeconds	1.3.6.1.2.1.10.94.1.1.65546.1.9	Counter32	read-only	Error seconds of the ATUR FEC within 15 minutes.
C32 hwAdslPortAturHecDropCellsCnt	1.3.6.1.2.1.10.94.1.1.65546.1.12	Counter32	read-only	ATUR cells discarded with HEC Errors.
C32 hwAdslPortCurrent15minutesTimeElapse	1.3.6.1.2.1.10.94.1.1.65546.1.10	Counter32	read-only	Seconds that is passed within the current 15 minutes.
INT hwAdslPortCurrentActMode	1.3.6.1.2.1.10.94.1.1.65546.1.44	INTEGER	read-only	Instantaneous value of the technology type that line is currently trained up under. Options: 1. adsl(1) - Indicates that line is currently trained up under adsl type 2. adsl2(2) - Indicates that line is currently trained up under adsl2 type 3. adsl2plus(3) - Indicates that line is currently trained up under adsl2+ type
hwAdslPortPerformanceStatEntry	1.3.6.1.2.1.10.94.1.1.65546.1		not-accessible	This table is used to describe the performance statistics of the ADSL port within 15 minutes. The indexes of this entry are ifIndex and hwAdslPort15minutesPerformanceInterval.
hwAdslPortPerformanceStatTable	1.3.6.1.2.1.10.94.1.1.65546		not-accessible	This table is used to describe the performance statistics of the ADSL port within 15 minutes. The indexes of this table are ifIndex and hwAdslPort15minutesPerformanceInterval.
NTF hwAdslPortRateChangeTrap	1.3.6.1.2.1.10.94.1.2.65536.1.0.2			ADSL act rate is change trap. This trap message is generated when the ADSL port rate change.
INT hwAdslPortRateChangeTrapConfig	1.3.6.1.2.1.10.94.1.1.65548.1	INTEGER	read-write	Enable or disable ADSL port line-rate change trap feature. Options: 1. enabled(1) - ADSL port line-rate change trap feature is enabled 2. disabled(2) - ADSL port line-rate change trap feature is disabled
G32 hwAdslPortRateChangeTrapDSLineRate	1.3.6.1.2.1.10.94.1.1.65547.1.4	Gauge32	accessible-for-notify	Down stream line rate after line rate change.
OCT hwAdslPortRateChangeTrapDslType	1.3.6.1.2.1.10.94.1.1.65547.1.7	OCTET STRING	accessible-for-notify	DSL line type of the port whose rate changes.
OCT hwAdslPortRateChangeTrapEventType	1.3.6.1.2.1.10.94.1.1.65547.1.6	OCTET STRING	accessible-for-notify	Event type reported during the previous change of the rate. If both the upstream and downstream rates change, this leaf object outputs character string 'DU'. If only the upstream rates changes, this leaf object outputs character string 'US'. If only the downstream rates changes, this leaf object outputs character string 'DS'.
OCT hwAdslPortRateChangeTrapIPIAID	1.3.6.1.2.1.10.94.1.1.65547.1.1	OCTET STRING	accessible-for-notify	The port IPIAID is reported when the port rate changes.
OCT hwAdslPortRateChangeTrapMUXID	1.3.6.1.2.1.10.94.1.1.65547.1.2	OCTET STRING	accessible-for-notify	The port MUXID is reported when the port rate changes.
hwAdslPortRateChangeTrapParaEntry	1.3.6.1.2.1.10.94.1.1.65547.1		not-accessible	ADSL line rate change trap parameter table. The index of this entry is ifIndex.
hwAdslPortRateChangeTrapParaTable	1.3.6.1.2.1.10.94.1.1.65547		not-accessible	ADSL line rate change trap parameter table. The index of this table is ifIndex.
C32 hwAdslPortRateChangeTrapTimeStamp	1.3.6.1.2.1.10.94.1.1.65547.1.3	Counter32	accessible-for-notify	The time stamp of Line rate change trap. Standard Unix format; as the number of seconds since 1/1/1970 (UNIT:Second).
G32 hwAdslPortRateChangeTrapUSLineRate	1.3.6.1.2.1.10.94.1.1.65547.1.5	Gauge32	accessible-for-notify	Up stream line rate after line rate change.
C32 hwAdslPortSyncFailNumber	1.3.6.1.2.1.10.94.1.1.65546.1.5	Counter32	read-only	Number of failed activations within 15 minutes.
C32 hwAdslPortSyncSuccNumber	1.3.6.1.2.1.10.94.1.1.65546.1.4	Counter32	read-only	Number of successful activations within 15 minutes.
DAT hwAdslPreActiveTime	1.3.6.1.2.1.10.94.1.1.65539.1.7	DateAndTime	read-only	The last time at that the port was activated.
INT hwAdslTransmissionMode	1.3.6.1.2.1.10.94.1.1.14.1.65539	INTEGER	read-create	Indicates the transmission mode of this channel. Options: 1. all(1) - All (G992.1, G992.2, T1.413)(Default) 2. fullRate(2) - Full rate(G992.1 or T1.413) 3. gliteOnly(3) - G992.2(g.lite) only 4. t1413Only(4) - T1.413 only 5. gdmtOnly(5) - G992.1,G992.3,G992.5,(g.dmt) only 6. ghs(6) - g.hs (G992.1,G992.2,G992.3,G992.4,G992.5,G992.5 is prior) 7. g992Dot1(7) - G992.1 8. g992Dot2(8) - G992.2 9. g992Dot3(9) - G992.3 10. g992Dot4(10) - G992.4 11. g992Dot5(11) - G992.5 12. adslAllOnly(12) - ADSL ALL ONLY 13. adslAndAdsl2(13) - G.992.1,G.992.3,T1.413(Not support) Default: all(1)
hwAdslTraps	1.3.6.1.2.1.10.94.1.2.65536
INT hwAdslTrellionsModeEnable	1.3.6.1.2.1.10.94.1.1.14.1.65538	INTEGER	read-create	Enables and disables the Trellions mode. Options: 1. enabled(1) - Indicates that the trellis coding is enabled 2. disabled(2) - Indicates that the trellis coding is disabled Default: enabled(1)
INT hwPortThreePriorityEnable	1.3.6.1.2.1.10.94.1.1.65540.1.1	INTEGER	read-write	Three Priority status of the interface. Options: 1. enable(1) - Adsl port three priority is enabled 2. disable(2) - Adsl port three priority is disabled
hwPortThreePriorityEntry	1.3.6.1.2.1.10.94.1.1.65540.1		not-accessible	Adsl port three priority table. The index of this entry is ifIndex.
hwPortThreePriorityTable	1.3.6.1.2.1.10.94.1.1.65540		not-accessible	Adsl port three priority table. The index of this table is ifIndex.
INT hwSlotMacMaxNoLimitEnable	1.3.6.1.2.1.10.94.1.1.65541.1.1	INTEGER	read-write	This object is used to set whether all the ports in the slot limits the maximum number of learning MAC addresses. Options: 1. enable(1) - Don't limit the max NO. of learning mac addresses in the slot 2. disable(2) - Limit the max NO. of learning mac addresses in the slot
hwSlotMacMaxNoLimitEntry	1.3.6.1.2.1.10.94.1.1.65541.1		not-accessible	Max mac learning no limit table. The index of this entry is hwFrameIndex and hwSlotIndex.
hwSlotMacMaxNoLimitTable	1.3.6.1.2.1.10.94.1.1.65541		not-accessible	Max mac learning no limit table. The index of this table is hwFrameIndex and hwSlotIndex.
INT hwXdslDynamicInfoCollect	1.3.6.1.2.1.10.94.1.1.65552.1.1	INTEGER	read-write	Start Dynamic information collecting of Xdsl port. Options: 1. start(1) - Indicates that collecting data starts 2. invalid(-1) - Invalid value
hwXdslDynamicInfoCollectEntry	1.3.6.1.2.1.10.94.1.1.65552.1		not-accessible	The table hwXdslDynamicInfoCollectTable implement xDSL port Dynamic information collect. The index of this entry is hwFrameIndex and hwSlotIndex.
INT hwXdslDynamicInfoCollectStatus	1.3.6.1.2.1.10.94.1.1.65552.1.2	INTEGER	read-only	Board Dynamic information collecting status. Options: 1. noCollect(1) - Indicates that collecting data is not performed 2. collecting(2) - Indicates that collecting data is being performed 3. collected(3) - Indicates that collecting data is complete
hwXdslDynamicInfoCollectTable	1.3.6.1.2.1.10.94.1.1.65552		not-accessible	The table hwXdslDynamicInfoCollectTable implement xDSL port Dynamic information collect. The index of this table is hwFrameIndex and hwSlotIndex.
DAT hwXdslDynamicInfoCollectTime	1.3.6.1.2.1.10.94.1.1.65552.1.3	DateAndTime	read-only	Time when collecting the optimization information is complete.
INT hwxdslDynamicProfBandOptUsage	1.3.6.1.2.1.10.94.1.1.65550.1.46	INTEGER	read-create	Defines the VDSL link use of the optional frequency range [25kHz - 138kHz] (Opt). Options: 1. disable(1) - Indicates Opt is unused 2. enable(2) - Indicates Opt usage is for upstream 3. invalidValue(-1) - Invalid value Huawei defined.
INT hwxdslDynamicProfBitSwapDS	1.3.6.1.2.1.10.94.1.1.65550.1.3	INTEGER	read-create	Enables or disables the bit swap downstream of a line. Options: 1. disable(1) - The bit swap downstream of a line is disabled 2. enable(2) - The bit swap downstream of a line is enabled 3. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfBitSwapUS	1.3.6.1.2.1.10.94.1.1.65550.1.4	INTEGER	read-create	Enables or disables the bit swap upstream of a line. Options: 1. disable(1) - The bit swap upstream of a line is disabled 2. enable(2) - The bit swap upstream of a line is enabled 3. invalidValue(-1) - Invalid value
OCT hwxdslDynamicProfCarMaskDS	1.3.6.1.2.1.10.94.1.1.65550.1.35	OCTET STRING	read-create	Sub-carriers mask. A bitmap of 512 bits that allows masking up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the respective downstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCds < 512, all bits i (NSCds i <= 512) should be set to '1'.
OCT hwxdslDynamicProfCarMaskUS	1.3.6.1.2.1.10.94.1.1.65550.1.36	OCTET STRING	read-create	Sub-carriers mask. A bitmap of 64 bits that allows masking up to 64 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCus) is set to '1', the respective upstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCus < 64, all bits i (NSCus < i <= 64) should be set to '1'.
U32 hwxdslDynamicProfCh1MaxDelayDs	1.3.6.1.2.1.10.94.1.1.65550.1.13	Unsigned32	read-create	Maximum Interleave Delay on Downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay is as close as possible to, but less than or equal to, hwxdslDynamicProfCh1MaxDelayDs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Range: 0-200 Unit: milliseconds
U32 hwxdslDynamicProfCh1MaxDelayUs	1.3.6.1.2.1.10.94.1.1.65550.1.14	Unsigned32	read-create	Maximum Interleave Delay on Upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay is as close as possible to, but less than or equal to, hwxdslDynamicProfCh1MaxDelayUs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Range: 0-200 Unit: milliseconds
INT hwxdslDynamicProfCh1MinProtectionDs	1.3.6.1.2.1.10.94.1.1.65550.1.11	INTEGER	read-create	Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Options: 1. noProtection (1) - Indicates that the INP value is 0 2. halfSymbol (2) - Indicates that the INP value is 0.5 3. singleSymbol (3) - Indicates that the INP value is 1 4. twoSymbols (4) - Indicates that the INP value is 2 5. threeSymbols (5) - Indicates that the INP value is 3 6. fourSymbols (6) - Indicates that the INP value is 4 7. fiveSymbols (7) - Indicates that the INP value is 5 8. sixSymbols (8) - Indicates that the INP value is 6 9. sevenSymbols (9) - Indicates that the INP value is 7 10. eightSymbols (10) - Indicates that the INP value is 8 11. nineSymbols (11) - Indicates that the INP value is 9 12. tenSymbols (12) - Indicates that the INP value is 10 13. elevenSymbols (13) - Indicates that the INP value is 11 14. twelveSymbols (14) - Indicates that the INP value is 12 15. thirteenSymbols (15) - Indicates that the INP value is 13 16. fourteenSymbols (16) - Indicates that the INP value is 14 17. fifteenSymbols (17) - Indicates that the INP value is 15 18. sixteenSymbols (18) - Indicates that the INP value is 16 19. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfCh1MinProtectionUs	1.3.6.1.2.1.10.94.1.1.65550.1.12	INTEGER	read-create	Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Options: 1. noProtection (1) - Indicates that the INP value is 0 2. halfSymbol (2) - Indicates that the INP value is 0.5 3. singleSymbol (3) - Indicates that the INP value is 1 4. twoSymbols (4) - Indicates that the INP value is 2 5. threeSymbols (5) - Indicates that the INP value is 3 6. fourSymbols (6) - Indicates that the INP value is 4 7. fiveSymbols (7) - Indicates that the INP value is 5 8. sixSymbols (8) - Indicates that the INP value is 6 9. sevenSymbols (9) - Indicates that the INP value is 7 10. eightSymbols (10) - Indicates that the INP value is 8 11. nineSymbols (11) - Indicates that the INP value is 9 12. tenSymbols (12) - Indicates that the INP value is 10 13. elevenSymbols (13) - Indicates that the INP value is 11 14. twelveSymbols (14) - Indicates that the INP value is 12 15. thirteenSymbols (15) - Indicates that the INP value is 13 16. fourteenSymbols (16) - Indicates that the INP value is 14 17. fifteenSymbols (17) - Indicates that the INP value is 15 18. sixteenSymbols (18) - Indicates that the INP value is 16 19. invalidValue(-1) - Invalid value
U32 hwxdslDynamicProfCh2MaxDelayDs	1.3.6.1.2.1.10.94.1.1.65550.1.17	Unsigned32	read-create	Maximum Interleave Delay on Downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay is as close as possible to, but less than or equal to, hwxdslDynamicProfCh2MaxDelayDs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Range: 0-200 Unit: milliseconds
U32 hwxdslDynamicProfCh2MaxDelayUs	1.3.6.1.2.1.10.94.1.1.65550.1.18	Unsigned32	read-create	Maximum Interleave Delay on Upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay is as close as possible to, but less than or equal to, hwxdslDynamicProfCh2MaxDelayUs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Range: 0-200 Unit: milliseconds
INT hwxdslDynamicProfCh2MinProtectionDs	1.3.6.1.2.1.10.94.1.1.65550.1.15	INTEGER	read-create	Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Options: 1. noProtection (1) - Indicates that the INP value is 0 2. halfSymbol (2) - Indicates that the INP value is 0.5 3. singleSymbol (3) - Indicates that the INP value is 1 4. twoSymbols (4) - Indicates that the INP value is 2 5. threeSymbols (5) - Indicates that the INP value is 3 6. fourSymbols (6) - Indicates that the INP value is 4 7. fiveSymbols (7) - Indicates that the INP value is 5 8. sixSymbols (8) - Indicates that the INP value is 6 9. sevenSymbols (9) - Indicates that the INP value is 7 10. eightSymbols (10) - Indicates that the INP value is 8 11. nineSymbols (11) - Indicates that the INP value is 9 12. tenSymbols (12) - Indicates that the INP value is 10 13. elevenSymbols (13) - Indicates that the INP value is 11 14. twelveSymbols (14) - Indicates that the INP value is 12 15. thirteenSymbols (15) - Indicates that the INP value is 13 16. fourteenSymbols (16) - Indicates that the INP value is 14 17. fifteenSymbols (17) - Indicates that the INP value is 15 18. sixteenSymbols (18) - Indicates that the INP value is 16 19. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfCh2MinProtectionUs	1.3.6.1.2.1.10.94.1.1.65550.1.16	INTEGER	read-create	Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Options: 1. noProtection (1) - Indicates that the INP value is 0 2. halfSymbol (2) - Indicates that the INP value is 0.5 3. singleSymbol (3) - Indicates that the INP value is 1 4. twoSymbols (4) - Indicates that the INP value is 2 5. threeSymbols (5) - Indicates that the INP value is 3 6. fourSymbols (6) - Indicates that the INP value is 4 7. fiveSymbols (7) - Indicates that the INP value is 5 8. sixSymbols (8) - Indicates that the INP value is 6 9. sevenSymbols (9) - Indicates that the INP value is 7 10. eightSymbols (10) - Indicates that the INP value is 8 11. nineSymbols (11) - Indicates that the INP value is 9 12. tenSymbols (12) - Indicates that the INP value is 10 13. elevenSymbols (13) - Indicates that the INP value is 11 14. twelveSymbols (14) - Indicates that the INP value is 12 15. thirteenSymbols (15) - Indicates that the INP value is 13 16. fourteenSymbols (16) - Indicates that the INP value is 14 17. fifteenSymbols (17) - Indicates that the INP value is 15 18. sixteenSymbols (18) - Indicates that the INP value is 16 19. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfClassMask	1.3.6.1.2.1.10.94.1.1.65550.1.45	INTEGER	read-create	In order to reduce the number of configuration possibilities, the limit PSD masks are grouped in the following PSD mask classes: Options: 1. annexA998-D-32(1) - Class 998 Annex A: D-32, D-64, D-48, D-128 2. annexA998-D-64(2) - Class 998 Annex A: D-32, D-64, D-48, D-128 3. annexB997-M1c-A-7(3) - Class 997-M1c Annex B: 997-M1c-A-7 4. annexB997-M1x-M-8(4) - Class 997-M1x Annex B: 997-M1x-M-8, 997-M1x-M 5. annexB997-M1x-M(5) - Class 997-M1x Annex B: 997-M1x-M-8, 997-M1x-M 6. annexB997-M2x-M-8(6) - Class 997-M2x Annex B: 997-M2x-M-8, 997-M2x-A, 997-M2x-M 7. annexB997-M2x-A(7) - Class 997-M2x Annex B: 997-M2x-M-8, 997-M2x-A, 997-M2x-M 8. annexB997-M2x-M(8) - Class 997-M2x Annex B: 997-M2x-M-8, 997-M2x-A, 997-M2x-M 9. annexB998-M1x-A(9) - Class 998-M1x Annex B: 998-M1x-A, 998-M1x-B, 998-M1x-NUS0 10. annexB998-M1x-B(10) - Class 998-M1x Annex B: 998-M1x-A, 998-M1x-B, 998-M1x-NUS0 11. annexB998-M1x-NUS0(11) - Class 998-M1x Annex B: 998-M1x-A, 998-M1x-B, 998-M1x-NUS0 12. annexB998-M2x-A(12) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0 13. annexB998-M2x-M(13) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0 14. annexB998-M2x-B(14) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0 15. annexB998-M2x-NUS0(15) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0 16. annexBHPE17-M1(16) - Class HPE17 Annex B: HPE17-M1 17. annexBHPE30-M1(17) - Class HPE30 Annex B: HPE30-M1 18. annexB997E17-M2x-A(18) - Class 997E17-M2x Annex B: 997E17-M2x-A 19. annexB997E30-M2x-NUS0(19) - Class 997E30-M2x Annex B: 997E30-M2x-NUS0 20. annexB998E17-M2x-NUS0(20) - Class 998E17-M2x Annex B: 998E17-M2x-NUS0, 998E17-M2x-NUS0-M 21. annexB998E17-M2x-NUS0-M(21) - Class 998E17-M2x Annex B: 998E17-M2x-NUS0, 998E17-M2x-NUS0-M 22. annexB998ADE17-M2x-NUS0-M(22) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M. 23. annexB998ADE17-M2x-B(23) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M. 24. annexB998E30-M2x-NUS0(24) - Class 998E30-M2x Annex B: 998E30-M2x-NUS0, 998E30-M2x-NUS0-M 25. annexB998E30-M2x-NUS0-M(25) - Class 998E30-M2x Annex B: 998E30-M2x-NUS0, 998E30-M2x-NUS0-M 26. annexB998ADE30-M2x-NUS0-M(26) - Class 998ADE30-M2x Annex B: 998ADE30-M2x-NUS0-M, 998ADE30-M2x-NUS0-A 27. annexB998ADE17-M2x-A(27) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M. 28. annexB998ADE30-M2x-NUS0-A(28) - Class 998ADE30-M2x Annex B: 998ADE30-M2x-NUS0-M, 998ADE30-M2x-NUS0-A 29. annexA998-D-48(29) - Class 998 Annex A: D-32, D-64, D-48, D-128 30. annexA998-D-128(30) - Class 998 Annex A: D-32, D-64, D-48, D-128 31. annexB998ADE17-M2x-M(31) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M. 32. invalidValue(-1) - Invalid value
OCT hwxdslDynamicProfDpboEPsd	1.3.6.1.2.1.10.94.1.1.65550.1.24	OCTET STRING	read-create	This parameter defines the PSD mask that is assumed to be permitted at the exchange. This parameter shall use the same format as PSDMASKds. The maximum number of breakpoints for DPBOEPSD is 16. This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value 0xff.
OCT hwxdslDynamicProfDpboEscm	1.3.6.1.2.1.10.94.1.1.65550.1.26	OCTET STRING	read-create	This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid. Octets 0+1 DPBOESCMA Octets 2+3 DPBOESCMB Octets 4+5 DPBOESCMC
U32 hwxdslDynamicProfDpboEsEL	1.3.6.1.2.1.10.94.1.1.65550.1.25	Unsigned32	read-create	This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back-off depending on this length. For this parameter the electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. DPBOESEL shall be coded as an unsigned integer representing an electrical length from 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB. All values in the range are valid.If DPBOESEL is set to zero, the DPBO in this section shall be disabled. Range: 0-511 Unit: 0.5dB
U32 hwxdslDynamicProfDpboFMax	1.3.6.1.2.1.10.94.1.1.65550.1.29	Unsigned32	read-create	DPBOFMAX defines the maximum frequency at which DPBO may be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956). Range: 32-6956 Unit: 4.3125 KHz
U32 hwxdslDynamicProfDpboFMin	1.3.6.1.2.1.10.94.1.1.65550.1.28	Unsigned32	read-create	DPBOFMIN defines the minimum frequency from which the DPBO shall be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 0 kHz (coded as 0) to 8832 kHz (coded as 2048). Range: 0-2048 Unit: 4.3125 KHz
U32 hwxdslDynamicProfDpboMus	1.3.6.1.2.1.10.94.1.1.65550.1.27	Unsigned32	read-create	DPBOMUS defines the assumed Minimum Usable receive Signal PSD (in dBm/Hz) for exchange based services, used to modify parameter DPBOFMAX defined below. It shall be coded as an unsigned integer representing a PSD level from 0 dBm/Hz (coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz. All values in the range are valid. Range: 0-255 Unit: 0.5dBm/Hz
hwxdslDynamicProfEntry	1.3.6.1.2.1.10.94.1.1.65550.1		not-accessible	This table includes common parameters of the xdsl Dynamic profile. The index of this entry is hwxdslDynamicProfProfileName.
U32 hwxdslDynamicProfL0Time	1.3.6.1.2.1.10.94.1.1.65550.1.20	Unsigned32	read-create	This minimum time (in seconds) between an Exit from the L2 state and the next Entry into the L2 state. It ranges from 0 to 255 seconds. Range: 0-255
U32 hwxdslDynamicProfL2Atpr	1.3.6.1.2.1.10.94.1.1.65550.1.22	Unsigned32	read-create	The maximum aggregate transmit power reduction (in dB) that can be performed at transition of L0 to L2 state or through a single Power Trim in the L2 state. It ranges from 0 dB to 31 dB. Range: 0-31 Unit: dB
U32 hwxdslDynamicProfL2Atprt	1.3.6.1.2.1.10.94.1.1.65550.1.23	Unsigned32	read-create	The total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Request (i.e., at transition of L0 to L2 state) and Power Trims. Range: 0-31 Unit: dB
U32 hwxdslDynamicProfL2Time	1.3.6.1.2.1.10.94.1.1.65550.1.21	Unsigned32	read-create	This minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. It ranges from 0 to 255 seconds. Range: 0-255
INT hwxdslDynamicProfLimitMask	1.3.6.1.2.1.10.94.1.1.65550.1.44	INTEGER	read-create	This configuration parameter contains the G.993.2 profiles to be allowed by the near-end xTU on this line. Options: 1. profile8a (1) - The G.993.2 profile is profile8a 2. profile8b (2) - The G.993.2 profile is profile8b 3. profile8c (3) - The G.993.2 profile is profile8c 4. profile8d (4) - The G.993.2 profile is profile8d 5. profile12a (5) - The G.993.2 profile is profile12a 6. profile12b (6) - The G.993.2 profile is profile12b 7. profile17a (7) - The G.993.2 profile is profile17a 8. profile30a (8) - The G.993.2 profile is profile30a 9. invalidValue(-1) - Invalid value
U32 hwxdslDynamicProfMaxNomAtpDs	1.3.6.1.2.1.10.94.1.1.65550.1.40	Unsigned32	read-create	The maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm). Range: 0-255 Unit: 0.1 dBm
U32 hwxdslDynamicProfMaxNomAtpUs	1.3.6.1.2.1.10.94.1.1.65550.1.41	Unsigned32	read-create	The maximum nominal aggregate transmit power in the upstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm). Range: 0-255 Unit: 0.1 dBm
I32 hwxdslDynamicProfMaxNomPsdDs	1.3.6.1.2.1.10.94.1.1.65550.1.38	Integer32	read-create	The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz(physical values are -60 to -30 dBm/Hz). The invalid value is -1. If data is invalid, the invalid value will be returned. Unit: 0.1 dB
I32 hwxdslDynamicProfMaxNomPsdUs	1.3.6.1.2.1.10.94.1.1.65550.1.39	Integer32	read-create	The maximum nominal transmit PSD in the upstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz(physical values are -60 to -30 dBm/Hz). The invalid value is -1. If data is invalid, the invalid value will be returned. Unit: 0.1 dB
U32 hwxdslDynamicProfMaxSnrmDs	1.3.6.1.2.1.10.94.1.1.65550.1.7	Unsigned32	read-create	The maximum Noise Margin the xTU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
U32 hwxdslDynamicProfMaxSnrmUs	1.3.6.1.2.1.10.94.1.1.65550.1.8	Unsigned32	read-create	The maximum Noise Margin the xTU-C receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
U32 hwxdslDynamicProfMinSnrmDs	1.3.6.1.2.1.10.94.1.1.65550.1.9	Unsigned32	read-create	The minimum Noise Margin the xTU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
U32 hwxdslDynamicProfMinSnrmUs	1.3.6.1.2.1.10.94.1.1.65550.1.10	Unsigned32	read-create	The minimum Noise Margin the xTU-C receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
BIT hwxdslDynamicProfPmMode	1.3.6.1.2.1.10.94.1.1.65550.1.19	Bits	read-create	Power management state Enabling. Defines the power states the xTU-C or xTU-R may autonomously transition to on this line. The various bit positions are: allowTransitionsToIdle (0) and allowTransitionsToLowPower (1). A bit with a '1' value means that the xTU is allowed to transit into the respective state and a '0' value means that the xTU is not allowed to transit into the respective state.
OCT hwxdslDynamicProfProfileName	1.3.6.1.2.1.10.94.1.1.65550.1.1	OCTET STRING	not-accessible	The name of xdsl Dynamic Profile.
OCT hwxdslDynamicProfPsdMaskDs	1.3.6.1.2.1.10.94.1.1.65550.1.42	OCTET STRING	read-create	This configuration parameter defines the downstream PSD mask applicable at the U C2 reference point. This MIB PSD mask may impose PSD restrictions in addition to the Limit PSD mask defined in the relevant Recommendation (e.g., G.992.5, G.993.2). This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCds - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 32, all remaining octets are set to the value 0xff. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
OCT hwxdslDynamicProfPsdMaskUs	1.3.6.1.2.1.10.94.1.1.65550.1.43	OCTET STRING	read-create	This configuration parameter defines the upstream PSD mask applicable at the U R2 reference point. This MIB PSD mask may impose PSD restrictions in addition to the Limit PSD mask defined in the relevant Recommendations (e.g., ITU-T Recommendations G.992.3, G.993.2). This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 45-47 - Same, for a 3rd breakpoint. This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCus - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value 0xff. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
OCT hwxdslDynamicProfRfiBands	1.3.6.1.2.1.10.94.1.1.65550.1.33	OCTET STRING	read-create	The subset of PSD mask breakpoints that shall be used to notch an RFI band. It is a string of bands consist of begin tone index and end tone index. for example :0-10,20-50,100-4095 It can contain as most as 16 bands.
ROW hwxdslDynamicProfRowStatus	1.3.6.1.2.1.10.94.1.1.65550.1.51	RowStatus	read-create	This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be first unreferenced from all associated templates.
hwxdslDynamicProfTable	1.3.6.1.2.1.10.94.1.1.65550		not-accessible	This table includes common parameters of the xdsl Dynamic profile. The index of this table is hwxdslDynamicProfProfileName.
U32 hwxdslDynamicProfTargetSnrmDs	1.3.6.1.2.1.10.94.1.1.65550.1.5	Unsigned32	read-create	The target Noise Margin the xTU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
U32 hwxdslDynamicProfTargetSnrmUs	1.3.6.1.2.1.10.94.1.1.65550.1.6	Unsigned32	read-create	The target Noise Margin the xTU-C receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
OCT hwxdslDynamicProfToneBlackOut	1.3.6.1.2.1.10.94.1.1.65550.1.34	OCTET STRING	read-create	The subset of subcarriermask that shall be used to mask the subcarriers. It is a string of bands consist of begin tone index and end tone index. for example :0-10,20-50,100-4095 It can contain as most as 8 bands.
U32 hwxdslDynamicProfUpboKL	1.3.6.1.2.1.10.94.1.1.65550.1.32	Unsigned32	read-create	This parameter defines the electrical loop length expressed in dB at 1MHz, kl0, configured by the CO-MIB. The value shall be coded as an unsigned 16 bit number in the range 0 (coded as 0) to 128 dB (coded as 1280) in steps of 0.1 dB. Range: 0-1280 Unit: 0.1 dB
INT hwxdslDynamicProfUpboKLF	1.3.6.1.2.1.10.94.1.1.65550.1.31	INTEGER	read-create	This parameter is a flag that forces the VTU-R to use the electrical loop length of the CO-MIB (UPBOKL) to compute the UPBO. The value shall be forced if the flag is set to 1. Otherwise, the electrical loop length shall be autonomously selected by the VTU-O. Options: 1. forced(1) - Force the CPE to use the electrical length of the CO(UPBOKL) to compute the UPBO 2. auto(2) - Electrical length shall be autonomously selected by the CO 3. invalidValue(-1) - Invalid value
OCT hwxdslDynamicProfUpboPsdBand	1.3.6.1.2.1.10.94.1.1.65550.1.30	OCTET STRING	read-create	This parameter defines the UPBO reference PSD used to compute the upstream power back-off for each upstream band except US0. A UPBOPSD defined for each band ahsll consist of two parameters [a, b]. Parameter a shall be coded as an unsigned 12-bit number from 40 dBm/Hz (coded as 0) to 80.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz; and b shall be coded as an unsigned 12 bit number from 0 (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency f expressed in MHz shall be equal to '-a-b(SQRT(f))'. The set of parameter values a = 40 dBm/Hz, b = 0 dBm/Hz is a special configuration to disable UPBO in the respective upstream band. Octets 0+1 - a[0] Octets 2+3 - b[0] Octets 4+5 - a[1] Octets 6+7 - b[1] Octets 8+9 - a[2] Octets 10+11 - b[2] Octets 12+13 - a[3] Octets 14+15 - b[3]
OCT hwxdslDynamicProfVirtualNoiseDs	1.3.6.1.2.1.10.94.1.1.65550.1.49	OCTET STRING	read-create	The Virtual Noise of downsteam. This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCds - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (127.5dBm/Hz) with steps of 0.5dBm/Hz.
INT hwxdslDynamicProfVirtualNoiseModeDs	1.3.6.1.2.1.10.94.1.1.65550.1.47	INTEGER	read-create	Defines the Virtual Noise of downsteam. Options: 1. disable(1) - Unused 2. enable(2) - Used 3. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfVirtualNoiseModeUs	1.3.6.1.2.1.10.94.1.1.65550.1.48	INTEGER	read-create	Defines the Virtual Noise of upstream. Options: 1. disable(1) - Unused 2. enable(2) - Used 3. invalidValue(-1) - Invalid value
OCT hwxdslDynamicProfVirtualNoiseUs	1.3.6.1.2.1.10.94.1.1.65550.1.50	OCTET STRING	read-create	The Virtual Noise of upsteam. This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCds - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (127.5dBm/Hz) with steps of 0.5dBm/Hz.
INT hwxdslDynamicProfXdslMode	1.3.6.1.2.1.10.94.1.1.65550.1.37	INTEGER	read-create	The XDSL Mode is a way of categorizing the various XDSL transmission modes into groups, each group (XDSL Mode) shares the same PSD configuration. Options: 1. defMode (1) - XDSL transmit mode is defMode 2. adsl (2) - XDSL transmit mode is adsl 3. adsl2Pots (3) - XDSL transmit mode is adsl2Pots 4. adsl2Isdn (4) - XDSL transmit mode is adsl2Isdn 5. adsl2PlusPots (5) - XDSL transmit mode is adsl2PlusPots 6. adsl2PlusIsdn (6) - XDSL transmit mode is adsl2PlusIsdn 7. adsl2ReachExtended (7) - XDSL transmit mode is adsl2ReachExtended 8. g9923PotsNonOverlapped(8) - XDSL transmit mode is g9923PotsNonOverlapped 9. g9923PotsOverlapped(9) - XDSL transmit mode is g9923PotsOverlapped 10. g9923IsdnNonOverlapped(10) - XDSL transmit mode is g9923IsdnNonOverlapped 11. g9923isdnOverlapped(11) - XDSL transmit mode is g9923isdnOverlapped 12. g9924potsNonOverlapped(14) - XDSL transmit mode is g9924potsNonOverlapped 13. g9924potsOverlapped(15) - XDSL transmit mode is g9924potsOverlapped 14. g9923AnnexIAllDigNonOverlapped(18) - XDSL transmit mode is g9923AnnexIAllDigNonOverlapped 15. g9923AnnexIAllDigOverlapped(19) - XDSL transmit mode is g9923AnnexIAllDigOverlapped 16. g9923AnnexJAllDigNonOverlapped(20) - XDSL transmit mode is g9923AnnexJAllDigNonOverlapped 17. g9923AnnexJAllDigOverlapped(21) - XDSL transmit mode is g9923AnnexJAllDigOverlapped 18. g9924AnnexIAllDigNonOverlapped(22) - XDSL transmit mode is g9924AnnexIAllDigNonOverlapped 19. g9924AnnexIAllDigOverlapped(23) - XDSL transmit mode is g9924AnnexIAllDigOverlapped 20. g9923AnnexLMode1NonOverlapped(24) - XDSL transmit mode is g9923AnnexLMode1NonOverlapped 21. g9923AnnexLMode2NonOverlapped(25) - XDSL transmit mode is g9923AnnexLMode2NonOverlapped 22. g9923AnnexLMode3Overlapped(26) - XDSL transmit mode is g9923AnnexLMode3Overlapped 23. g9923AnnexLMode4Overlapped(27) - XDSL transmit mode is g9923AnnexLMode4Overlapped 24. g9923AnnexMPotsNonOverlapped(28) - XDSL transmit mode is g9923AnnexMPotsNonOverlapped 25. g9923AnnexMPotsOverlapped(29) - XDSL transmit mode is g9923AnnexMPotsOverlapped 26. g9925PotsNonOverlapped(30) - XDSL transmit mode is g9925PotsNonOverlapped 27. g9925PotsOverlapped(31) - XDSL transmit mode is g9925PotsOverlapped 28. g9925IsdnNonOverlapped(32) - XDSL transmit mode is g9925IsdnNonOverlapped 29. g9925isdnOverlapped(33) - XDSL transmit mode is g9925isdnOverlapped 30. g9925AnnexIAllDigNonOverlapped(36) - XDSL transmit mode is g9925AnnexIAllDigNonOverlapped 31. g9925AnnexIAllDigOverlapped(37) - XDSL transmit mode is g9925AnnexIAllDigOverlapped 32. g9925AnnexJAllDigNonOverlapped(38) - XDSL transmit mode is g9925AnnexJAllDigNonOverlapped 33. g9925AnnexJAllDigOverlapped(39) - XDSL transmit mode is g9925AnnexJAllDigOverlapped 34. g9925AnnexMPotsNonOverlapped(40) - XDSL transmit mode is g9925AnnexMPotsNonOverlapped 35. g9925AnnexMPotsOverlapped(41) - XDSL transmit mode is g9925AnnexMPotsOverlapped 36. vdsl2Pots (42) - XDSL transmit mode is vdsl2Pots 37. vdsl2Isdn (43) - XDSL transmit mode is vdsl2Isdn 38. invalidValue(-1) - Invalid value
BIT hwxdslDynamicProfXtuTransSysEna	1.3.6.1.2.1.10.94.1.1.65550.1.2	Bits	read-create	Xtu Transmission System Enabling (ATSE). A list of the different coding types enabled in this profile. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the XTUs may apply the respective coding for the XDSL line. A bit set to '0' means that the XTUs cannot apply the respective coding for the XDSL line. All 'reserved' bits should be set to '0'.
C32 hwXdslPort15minutesPerformanceInBytes	1.3.6.1.2.1.10.94.1.1.65545.1.2	Counter32	read-only	Read the receive bytes of xDSL port during 15 minutes.
I32 hwXdslPort15minutesPerformanceInterval	1.3.6.1.2.1.10.94.1.1.65545.1.1	Integer32	not-accessible	The index of the interval which is queried. Range: 0-96
C32 hwXdslPort15minutesPerformanceOutBytes	1.3.6.1.2.1.10.94.1.1.65545.1.3	Counter32	read-only	Read the transmit bytes of xDSL port during 15 minutes.
C32 hwXdslPortAtucCodeViolation	1.3.6.1.2.1.10.94.1.1.65545.1.6	Counter32	read-only	Number of head errors of the ATUC cell within 15 minutes.
C32 hwXdslPortAtucFecSeconds	1.3.6.1.2.1.10.94.1.1.65545.1.8	Counter32	read-only	Seconds of the ATUC FEC errors within 15 minutes.
C32 hwXdslPortAturCodeViolation	1.3.6.1.2.1.10.94.1.1.65545.1.7	Counter32	read-only	Number of head errors of the ATUR cell within 15 minutes.
C32 hwXdslPortAturFecSeconds	1.3.6.1.2.1.10.94.1.1.65545.1.9	Counter32	read-only	Seconds of the ATUR FEC errors within 15 minutes.
DAT hwXdslPortClearUpCntTime	1.3.6.1.2.1.10.94.1.1.65538.1.704	DateAndTime	read-only	The time when up counts of a Xdsl port is cleared.
C32 hwXdslPortCurrent15minutesStatTime	1.3.6.1.2.1.10.94.1.1.65545.1.10	Counter32	read-only	Seconds passed within the current 15 minutes.
I32 hwXdslPortCurrentDownRate	1.3.6.1.2.1.10.94.1.1.65538.1.501	Integer32	accessible-for-notify	Xdsl Port Current Downstream Value. Range: 0-30000 Default: 0
I32 hwXdslPortCurrentUpRate	1.3.6.1.2.1.10.94.1.1.65538.1.500	Integer32	accessible-for-notify	Xdsl Port Current Upstream Value. Range: 0-30000 Default: 0
I32 hwXdslPortDownThreshold	1.3.6.1.2.1.10.94.1.1.65538.1.811	Integer32	read-write	Set Port monitoring downstream rate threshold percent value. Range: 0-100
G32 hwXdslPortDownThresholdTxRate	1.3.6.1.2.1.10.94.1.1.65538.1.5	Gauge32	read-write	Set Port monitoring downstream rate threshold value. Default: 0 Unit: bps
hwXdslPortEntry	1.3.6.1.2.1.10.94.1.1.65538.1		not-accessible	This table includes xDSL(e.g. adsl,g.shdsl,vdsl...)port information, Used to support common attributes of the ADSL, G.SHDSL, and VDSL ports. The index of this entry is ifIndex.
INT hwXdslPortFarEndRunState	1.3.6.1.2.1.10.94.1.1.65538.1.600	INTEGER	read-only	Xdsl port far end Run state, This object is defaulted unknown(1). Options: 1. unknown(1) - Unknown status 2. noModem(2) - Port is not connected to modem 3. handshake(3) - Handshake status 4. showtime(4) - Port is activated
hwXdslPortIopCaptureEntry	1.3.6.1.2.1.10.94.1.1.65551.1		not-accessible	The table hwXdslPortIopCaptureTable implement xDSL port IOP information capture. The index of this entry is ifIndex.
INT hwXdslPortIopCaptureOperStatus	1.3.6.1.2.1.10.94.1.1.65551.1.2	INTEGER	read-only	Port IOP capture status. Options: 1. noCapture(1) - Indicates that the capture is not performed 2. capturing(2) - Indicates that the capture is being performed 3. iopGenerate(3) - Indicates that the IOP file is generated 4. captured(4) - Indicates that the capture is complete 5. invalid(-1) - Invalid value
INT hwXdslPortIopCaptureOperType	1.3.6.1.2.1.10.94.1.1.65551.1.1	INTEGER	read-write	Start or stop IOP information capture of xDSL port. Options: 1. start(1) - Start IOP information capture of xDSL port 2. stop(2) - Stop IOP information capture of xDSL port 3. invalid(-1) - Invalid value
hwXdslPortIopCaptureTable	1.3.6.1.2.1.10.94.1.1.65551		not-accessible	The table hwXdslPortIopCaptureTable implement xDSL port IOP information capture. The index of this table is ifIndex.
DAT hwXdslPortLastDownTime	1.3.6.1.2.1.10.94.1.1.65538.1.703	DateAndTime	read-only	Last down time of a Xdsl port.
U32 hwXdslPortLastRetrainReason	1.3.6.1.2.1.10.94.1.1.65538.1.706	Unsigned32	read-only	The last retrain reson of Xdsl Line, coded as bit mask. Only one bit can be set valid, all bits set valid means invalid retrain reason.
DAT hwXdslPortLastUpTime	1.3.6.1.2.1.10.94.1.1.65538.1.702	DateAndTime	read-only	Last up time of a Xdsl port.
INT hwXdslPortLoopFlag	1.3.6.1.2.1.10.94.1.1.65538.1.800	INTEGER	read-only	Loop flag. Options: 1. false(0) - No loop 2. true (1) - Loop
I32 hwXdslPortMaxMacLearn	1.3.6.1.2.1.10.94.1.1.65538.1.1	Integer32	read-write	Set Max MAC count on the XDSL port. Range: 0-255 Default: 255
INT hwXdslPortNTEPowerStatus	1.3.6.1.2.1.10.94.1.1.65538.1.8	INTEGER	read-only	NTE power status, this object is defaulted off(2). Options: 1. on(1) - NTE power on 2. off(2) - NTE power off 3. unknown(3) - Unknown status
hwXdslPortPerformanceStatEntry	1.3.6.1.2.1.10.94.1.1.65545.1		not-accessible	XDSL port performance statistic table. The indexes of this entry are ifIndex and hwXdslPort15minutesPerformanceInterval.
hwXdslPortPerformanceStatTable	1.3.6.1.2.1.10.94.1.1.65545		not-accessible	XDSL port performance statistic table. The indexes of this table are ifIndex and hwXdslPort15minutesPerformanceInterval.
INT hwXdslPortPowerState	1.3.6.1.2.1.10.94.1.1.65538.1.601	INTEGER	read-only	Xdsl port power state. Options: 1. l0(1) - Full-on state 2. l2(2) - Low power state 3. l3(3) - Idle state 4. l1(4) - Low power state 5. invalidValue(-1) - Invalid value Default: l0(1)
INT hwXdslPortRateMonitorAlarmEnable	1.3.6.1.2.1.10.94.1.1.65538.1.6	INTEGER	read-write	Enables/Disables port rate monitor alarm. Options: 1. enabled(1) - The port rate monitor alarm is enabled 2. disabled(2) - The port rate monitor alarm is disabled
I32 hwXdslPortRateMonitorThreshold	1.3.6.1.2.1.10.94.1.1.65538.1.2	Integer32	read-write	Set Port monitoring rate threshold percent. Including upstream and downstream. Range: 0-100 Default: 0
U32 hwXdslPortRetrainCnt	1.3.6.1.2.1.10.94.1.1.65538.1.705	Unsigned32	read-only	The retrain counts of Xdsl Line.
OCT hwXdslPortStateBitmapList	1.3.6.1.2.1.10.94.1.1.65542.1.2	OCTET STRING	read-only	The type of port status: 2 failed; 8 testing; 9 activated; 10 activating; 11 deactivated; 18 localloopback; 19 remoteloopback; 20 blocked; 37 utopialoopback; 38 afeloopback; 39 hybridloopback; 255 unknown; HwXdslPortStateBitmapList describes the states of all ports. Every byte describe the current state of every port. The length is equal to the value of the hwXdslPortStatePortNumber.
U32 hwXdslPortStatePortNumber	1.3.6.1.2.1.10.94.1.1.65542.1.1	Unsigned32	read-only	This Object is Port Number of One Slot.
hwXdslPortStateStatisticEntry	1.3.6.1.2.1.10.94.1.1.65542.1		not-accessible	XDSL port state statistic table, used to support the statistics information about the status mapping and status of ports on the service boards, such as the ADSL, G.SHDSL and VDSL boards. The indexes of this entry are ifType, hwFrameIndex, and hwSlotIndex.
hwXdslPortStateStatisticTable	1.3.6.1.2.1.10.94.1.1.65542		not-accessible	XDSL port state statistic table, used to support the statistics information about the status mapping and status of ports on the service boards, such as the ADSL, G.SHDSL and VDSL boards. The indexes of this table are ifType, hwFrameIndex, and hwSlotIndex.
C32 hwXdslPortSyncFailNumber	1.3.6.1.2.1.10.94.1.1.65545.1.5	Counter32	read-only	Number of failed activations of the xDSL port within 15 minutes.
C32 hwXdslPortSyncSuccNumber	1.3.6.1.2.1.10.94.1.1.65545.1.4	Counter32	read-only	Number of successful activations of the xDSL port within 15 minutes.
hwXdslPortTable	1.3.6.1.2.1.10.94.1.1.65538		not-accessible	This table includes xDSL(e.g. adsl,g.shdsl,vdsl...)port information, Used to support common attributes of the ADSL, G.SHDSL, and VDSL ports. The index of this table is ifIndex.
U32 hwXdslPortUpCnt	1.3.6.1.2.1.10.94.1.1.65538.1.700	Unsigned32	read-only	The up counts of Xdsl port.
INT hwXdslPortUpCntAdminStatus	1.3.6.1.2.1.10.94.1.1.65538.1.701	INTEGER	read-write	Admin the up counts of xDSL port. Options: 1. reset(0) - Reset the up counts of xDSL port
I32 hwXdslPortUpThreshold	1.3.6.1.2.1.10.94.1.1.65538.1.810	Integer32	read-write	Set Port monitoring upstream rate threshold percent value. Range: 0-100
G32 hwXdslPortUpThresholdTxRate	1.3.6.1.2.1.10.94.1.1.65538.1.4	Gauge32	read-write	Set Port monitoring upstream rate threshold value. Default: 0 Unit: bps
C32 hwXdslPortUpTime	1.3.6.1.2.1.10.94.1.1.65538.1.7	Counter32	read-only	Duration of the xDSL port activation. Unit: seconds
hwXdslSysManagementParaTable	1.3.6.1.2.1.10.94.1.1.65548
U32 hwXdslTotalOfActivatedPorts	1.3.6.1.2.1.10.94.1.1.65542.1.3	Unsigned32	read-only	The total of the activated ports.
U32 hwXdslTotalOfActivatingPorts	1.3.6.1.2.1.10.94.1.1.65542.1.5	Unsigned32	read-only	The total of the activating ports.
U32 hwXdslTotalOfBlockedPorts	1.3.6.1.2.1.10.94.1.1.65542.1.7	Unsigned32	read-only	The total of the blocked ports.
U32 hwXdslTotalOfDeactivatedPorts	1.3.6.1.2.1.10.94.1.1.65542.1.4	Unsigned32	read-only	The total of the deactivated ports.
U32 hwXdslTotalOfFailedPorts	1.3.6.1.2.1.10.94.1.1.65542.1.10	Unsigned32	read-only	The total of the failed ports.
U32 hwXdslTotalOfLocalLoopbackPorts	1.3.6.1.2.1.10.94.1.1.65542.1.8	Unsigned32	read-only	The total of the local testing ports.
U32 hwXdslTotalOfRemoteLoopbackPorts	1.3.6.1.2.1.10.94.1.1.65542.1.9	Unsigned32	read-only	The total of the remote testing ports.
U32 hwXdslTotalOfTestingPorts	1.3.6.1.2.1.10.94.1.1.65542.1.6	Unsigned32	read-only	The total of the Testing ports.
U32 hwXdslTotalOfUnknownPorts	1.3.6.1.2.1.10.94.1.1.65542.1.11	Unsigned32	read-only	The total of the unknown testing ports.

OID symbolic	OID numeric	Type	Access	Description
OCT hwadslLineExtConfProfile	1.3.6.1.2.1.10.94.1.1.1.1.65536	OCTET STRING	read-write	The value of this object identifies the row in the ADSL Extend Line Configuration Profile Table, (adslLineExtConfProfileTable), which applies to this ADSL line, and channels if applicable. NULL - indicates that there is no extend line profile bound to this port. Range: 0-32
OCT hwadslLineDynamicProfile	1.3.6.1.2.1.10.94.1.1.1.1.65537	OCTET STRING	read-write	The value of this object identifies the row in the ADSL Dynamic Profile Table,which applies to this ADSL line, and channels if applicable. NULL - indicates that there is no Dynamic profile bound to this port. Range: 0-32
HWA hwAdslAtucCurrTransMode	1.3.6.1.2.1.10.94.1.1.2.1.65536	HWADSLTRANSMISSIONMODETYPE	read-only	A set of ADSL line transmission modes.
G32 hwAdslAtucCurrSignalAtn	1.3.6.1.2.1.10.94.1.1.2.1.65537	Gauge32	read-only	Current signal attenuation of the ATU-C, indicating the difference between the transmit signal of the ATU-R and the receive signal of the ATU-C. Range: 0-630 Unit: tenth dB
ADS hwadslAturTransmissionCapabilities	1.3.6.1.2.1.10.94.1.1.3.1.65535	Adsl2TransmissionModeType	read-only	The ATU transmission system capability list of the different coding types. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the ATU supports the respective coding. The value may be derived from the handshaking procedures defined in G.994.1.
G32 hwAdslAturCurrSignalAtn	1.3.6.1.2.1.10.94.1.1.3.1.65536	Gauge32	read-only	The signal attenuation value on ATUR: It indicates the difference between the transmit signal of the ATU-C and the receive signal of the ATU-R. Range: 0-630 Unit: tenth dB
G32 hwadslAtucChanCurrINP	1.3.6.1.2.1.10.94.1.1.4.1.65536	Gauge32	read-only	Indicates Impulse Noise Protection on downstream direction. The value multiply 1/10000 is the real value. Unit: DMT Symbol
G32 hwadslAtucChanRsSymbols	1.3.6.1.2.1.10.94.1.1.4.1.65537	Gauge32	read-only	Indicates Reed-Solomon symbols on downstream direction. The value multiply 1/10000 is the real value. Unit: byte
G32 hwadslAtucChanRsRedundancy	1.3.6.1.2.1.10.94.1.1.4.1.65538	Gauge32	read-only	Indicates Reed-Solomon redundancy on downstream direction. Unit: byte
G32 hwadslAtucChanRsDepth	1.3.6.1.2.1.10.94.1.1.4.1.65539	Gauge32	read-only	Indicates Reed-Solomon depth on downstream direction. Unit: byte
G32 hwadslAtucChanSymbolLength	1.3.6.1.2.1.10.94.1.1.4.1.65540	Gauge32	read-only	Indicates the Bit Number of the DMT Symbol on downstream direction. Unit: bit
G32 hwadslAtucChanPhyRrrcBits	1.3.6.1.2.1.10.94.1.1.4.1.65541	Gauge32	read-only	The bits in the channel that used to retransmission on downstream direction.
G32 hwadslAtucChanPhyRtxQueue	1.3.6.1.2.1.10.94.1.1.4.1.65542	Gauge32	read-only	Queues in send buffer on downstream direction.
G32 hwadslAtucChanRsSize	1.3.6.1.2.1.10.94.1.1.4.1.65543	Gauge32	read-only	Indicates Reed-Solomon Codeword Size on downstream direction . Range: 0-255 Unit: byte
G32 hwadslAtucChanCodeGain	1.3.6.1.2.1.10.94.1.1.4.1.65544	Gauge32	read-only	Indicates Code Gain on downstream direction. It ranges from 0 to 16 units of 0.5 dB (physical values are 0 to 8 dB).
G32 hwadslAtucChanPcb	1.3.6.1.2.1.10.94.1.1.4.1.65545	Gauge32	read-only	Indicates Power Cut-back on downstream direction. It ranges from 0 to 400 units of 0.1 dB(physical values are 0 to 40 dB). Unit: tenth dB
G32 hwadslAturChanCurrINP	1.3.6.1.2.1.10.94.1.1.5.1.65536	Gauge32	read-only	Indicates Impulse Noise Protection on upstream direction. The value multiply 1/10000 is the real value. Unit: DMT Symbol
G32 hwadslAturChanRsSymbols	1.3.6.1.2.1.10.94.1.1.5.1.65537	Gauge32	read-only	Indicates Reed-Solomon symbols on upstream direction. The value multiply 1/10000 is the real value. Unit: byte
G32 hwadslAturChanRsRedundancy	1.3.6.1.2.1.10.94.1.1.5.1.65538	Gauge32	read-only	Indicates Reed-Solomon redundancy on upstream direction. Unit: byte
G32 hwadslAturChanRsDepth	1.3.6.1.2.1.10.94.1.1.5.1.65539	Gauge32	read-only	Indicates Reed-Solomon depth on upstream direction. Unit: byte
G32 hwadslAturChanSymbolLength	1.3.6.1.2.1.10.94.1.1.5.1.65540	Gauge32	read-only	Indicates the Bit Number of the DMT Symbol on upstream direction. Unit: bit
G32 hwadslAturChanPhyRrrcBits	1.3.6.1.2.1.10.94.1.1.5.1.65541	Gauge32	read-only	The bits in the channel that used to retransmission on upstream direction.
G32 hwadslAturChanPhyRtxQueue	1.3.6.1.2.1.10.94.1.1.5.1.65542	Gauge32	read-only	Queues in send buffer on upstream direction.
G32 hwadslAturChanRsSize	1.3.6.1.2.1.10.94.1.1.5.1.65543	Gauge32	read-only	Indicates Reed-Solomon Codeword Size on upstream direction. Range: 0-255 Unit: byte
G32 hwadslAturChanCodeGain	1.3.6.1.2.1.10.94.1.1.5.1.65544	Gauge32	read-only	Indicates Code Gain on upstream direction. It ranges from 0 to 16 units of 0.5 dB (physical values are 0 to 8 dB).
C32 hwAdslAtucPerfFailFullInits	1.3.6.1.2.1.10.94.1.1.6.1.65535	Counter32	read-only	Count of the line initialization failed attempts since agent reset.
C32 hwAdslAtucPerfCurr15MinFailFullInits	1.3.6.1.2.1.10.94.1.1.6.1.65536	Counter32	read-only	Count of the line initialization failed attempts in the current 15 minute interval.
C32 hwAdslAtucPerfCurr1DayFailFullInits	1.3.6.1.2.1.10.94.1.1.6.1.65537	Counter32	read-only	Count of the line initialization failed attempts in the day as measured by adslAtucPerfCurr1DayTimeElapsed.
C32 hwAdslAtucPerfPrev1DayFailFullInits	1.3.6.1.2.1.10.94.1.1.6.1.65538	Counter32	read-only	Count of the line initialization failed attempts in the most recent previous 1-day period.
C32 hwAdslAtucIntervalFailFullInits	1.3.6.1.2.1.10.94.1.1.8.1.65535	Counter32	read-only	Count of the line initialization failed attempts during the interval.
C32 hwadslAtucChanFecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65536	Counter32	read-only	Count of all blocks received with FEC anomalies since agent reset.
C32 hwadslAtucChanHecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65537	Counter32	read-only	Count of all blocks received with HEC anomalies since agent reset.
C32 hwadslAtucChanCrcBlks	1.3.6.1.2.1.10.94.1.1.10.1.65538	Counter32	read-only	Count of all blocks received with CRC anomalies since agent reset.
C32 hwadslAtucChanPerfCurr15MinFecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65539	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel within the current 15 minute interval.
C32 hwadslAtucChanPerfCurr15MinHecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65540	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel within the current 15 minute interval.
C32 hwadslAtucChanPerfCurr15MinCrcBlks	1.3.6.1.2.1.10.94.1.1.10.1.65541	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel within the current 15 minute interval.
C32 hwadslAtucChanPerfCurr1DayFecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65542	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
C32 hwadslAtucChanPerfCurr1DayHecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65543	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
C32 hwadslAtucChanPerfCurr1DayCrcBlks	1.3.6.1.2.1.10.94.1.1.10.1.65544	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
C32 hwadslAtucChanPerfPrev1DayFecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65545	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel within the most recent previous 1-day period.
C32 hwadslAtucChanPerfPrev1DayHecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65546	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel within the most recent previous 1-day period.
C32 hwadslAtucChanPerfPrev1DayCrcBlks	1.3.6.1.2.1.10.94.1.1.10.1.65547	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel within the most recent previous 1-day period.
G32 hwadslAtucChanRtxCW	1.3.6.1.2.1.10.94.1.1.10.1.65548	Gauge32	read-only	Count of units request retransmission since agent reset.
G32 hwadslAtucChanRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65549	Gauge32	read-only	Count of units corrected by retransmission since agent reset.
G32 hwadslAtucChanRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65550	Gauge32	read-only	Count of units uncorrected by retransmission since agent reset.
G32 hwadslAtucChanPerfCurr15MinRtxCW	1.3.6.1.2.1.10.94.1.1.10.1.65551	Gauge32	read-only	Count of units request retransmission on this channel within the current 15 minute interval.
G32 hwadslAtucChanPerfCurr15MinRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65552	Gauge32	read-only	Count of units corrected by retransmission on this channel within the current 15 minute interval.
G32 hwadslAtucChanPerfCurr15MinRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65553	Gauge32	read-only	Count of units uncorrected by retransmission on this channel within the current 15 minute interval.
G32 hwadslAtucChanPerfCurr1DayRtxCW	1.3.6.1.2.1.10.94.1.1.10.1.65554	Gauge32	read-only	Count of units request retransmission on this channel during the current day.
G32 hwadslAtucChanPerfCurr1DayRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65555	Gauge32	read-only	Count of units corrected by retransmission on this channel during the current day.
G32 hwadslAtucChanPerfCurr1DayRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65556	Gauge32	read-only	Count of units uncorrected by retransmission on this channel during the current day.
G32 hwadslAtucChanPerfPrev1DayRtxCW	1.3.6.1.2.1.10.94.1.1.10.1.65557	Gauge32	read-only	Count of units request retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAtucChanPerfPrev1DayRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65558	Gauge32	read-only	Count of units corrected by retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAtucChanPerfPrev1DayRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65559	Gauge32	read-only	Count of units uncorrected by retransmission on this channel within the most recent previous 1-day period.
C32 hwadslAturChanFecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65536	Counter32	read-only	Count of all blocks received with FEC anomalies since agent reset.
C32 hwadslAturChanHecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65537	Counter32	read-only	Count of all blocks received with HEC anomalies since agent reset.
C32 hwadslAturChanCrcBlks	1.3.6.1.2.1.10.94.1.1.11.1.65538	Counter32	read-only	Count of all blocks received with CRC anomalies since agent reset.
C32 hwadslAturChanPerfCurr15MinFecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65539	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel within the current 15 minute interval.
C32 hwadslAturChanPerfCurr15MinHecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65540	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel within the current 15 minute interval.
C32 hwadslAturChanPerfCurr15MinCrcBlks	1.3.6.1.2.1.10.94.1.1.11.1.65541	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel within the current 15 minute interval.
C32 hwadslAturChanPerfCurr1DayFecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65542	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
C32 hwadslAturChanPerfCurr1DayHecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65543	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
C32 hwadslAturChanPerfCurr1DayCrcBlks	1.3.6.1.2.1.10.94.1.1.11.1.65544	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
C32 hwadslAturChanPerfPrev1DayFecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65545	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel within the most recent previous 1-day period.
C32 hwadslAturChanPerfPrev1DayHecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65546	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel within the most recent previous 1-day period.
C32 hwadslAturChanPerfPrev1DayCrcBlks	1.3.6.1.2.1.10.94.1.1.11.1.65547	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel within the most recent previous 1-day period.
G32 hwadslAturChanRtxCW	1.3.6.1.2.1.10.94.1.1.11.1.65548	Gauge32	read-only	Count of units request retransmission since agent reset.
G32 hwadslAturChanRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65549	Gauge32	read-only	Count of units corrected by retransmission since agent reset.
G32 hwadslAturChanRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65550	Gauge32	read-only	Count of units uncorrected by retransmission since agent reset.
G32 hwadslAturChanPerfCurr15MinRtxCW	1.3.6.1.2.1.10.94.1.1.11.1.65551	Gauge32	read-only	Count of units request retransmission on this channel within the current 15 minute interval.
G32 hwadslAturChanPerfCurr15MinRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65552	Gauge32	read-only	Count of units corrected by retransmission on this channel within the current 15 minute interval.
G32 hwadslAturChanPerfCurr15MinRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65553	Gauge32	read-only	Count of units uncorrected by retransmission on this channel within the current 15 minute interval.
G32 hwadslAturChanPerfCurr1DayRtxCW	1.3.6.1.2.1.10.94.1.1.11.1.65554	Gauge32	read-only	Count of units request retransmission on this channel during the current day.
G32 hwadslAturChanPerfCurr1DayRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65555	Gauge32	read-only	Count of units corrected by retransmission on this channel during the current day.
G32 hwadslAturChanPerfCurr1DayRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65556	Gauge32	read-only	Count of units uncorrected by retransmission on this channel during the current day.
G32 hwadslAturChanPerfPrev1DayRtxCW	1.3.6.1.2.1.10.94.1.1.11.1.65557	Gauge32	read-only	Count of units request retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAturChanPerfPrev1DayRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65558	Gauge32	read-only	Count of units corrected by retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAturChanPerfPrev1DayRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65559	Gauge32	read-only	Count of units uncorrected by retransmission on this channel within the most recent previous 1-day period.
NUM hwadslAtucChanIntervalFecBlks	1.3.6.1.2.1.10.94.1.1.12.1.65536	PerfIntervalCount	read-only	Count of all blocks received with FRC anomalies on this channel during this interval.
NUM hwadslAtucChanIntervalHecBlks	1.3.6.1.2.1.10.94.1.1.12.1.65537	PerfIntervalCount	read-only	Count of all blocks received with HRC anomalies on this channel during this interval.
NUM hwadslAtucChanIntervalCrcBlks	1.3.6.1.2.1.10.94.1.1.12.1.65538	PerfIntervalCount	read-only	Count of all blocks received with CRC anomalies on this channel during this interval.
G32 hwadslAtucChanIntervalRtxCW	1.3.6.1.2.1.10.94.1.1.12.1.65539	Gauge32	read-only	Count of units request retransmission on this channel during this interval.
G32 hwadslAtucChanIntervalRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.12.1.65540	Gauge32	read-only	Count of units corrected by retransmission on this channel during this interval.
G32 hwadslAtucChanIntervalRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.12.1.65541	Gauge32	read-only	Count of units uncorrected by retransmission on this channel during this interval.
NUM hwadslAturChanIntervalFecBlks	1.3.6.1.2.1.10.94.1.1.13.1.65536	PerfIntervalCount	read-only	Count of all blocks received with FRC anomalies on this channel during this interval.
NUM hwadslAturChanIntervalHecBlks	1.3.6.1.2.1.10.94.1.1.13.1.65537	PerfIntervalCount	read-only	Count of all blocks received with HRC anomalies on this channel during this interval.
NUM hwadslAturChanIntervalCrcBlks	1.3.6.1.2.1.10.94.1.1.13.1.65538	PerfIntervalCount	read-only	Count of all blocks received with CRC anomalies on this channel during this interval.
G32 hwadslAturChanIntervalRtxCW	1.3.6.1.2.1.10.94.1.1.13.1.65539	Gauge32	read-only	Count of units request retransmission on this channel during this interval.
G32 hwadslAturChanIntervalRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.13.1.65540	Gauge32	read-only	Count of units corrected by retransmission on this channel during this interval.
G32 hwadslAturChanIntervalRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.13.1.65541	Gauge32	read-only	Count of units uncorrected by retransmission on this channel during this interval.
INT hwAdslAtucConfDownBitSwap	1.3.6.1.2.1.10.94.1.1.14.1.65536	INTEGER	read-create	Enables and disables the down bitswap of a template. Options: 1. enabled(1) - Indicates that the downstream bit swap is enabled 2. disabled(2) - Indicates that the downstream bit swap is disabled Default: enabled(1)
INT hwAdslAtucConfUpBitSwap	1.3.6.1.2.1.10.94.1.1.14.1.65537	INTEGER	read-create	Enables and disables the up bitswap of a template. Options: 1. enabled(1) - Indicates that the upstream bit swap is enabled 2. disabled(2) - Indicates that the upstream bit swap is disabled Default: enabled(1)
INT hwAdslTrellionsModeEnable	1.3.6.1.2.1.10.94.1.1.14.1.65538	INTEGER	read-create	Enables and disables the Trellions mode. Options: 1. enabled(1) - Indicates that the trellis coding is enabled 2. disabled(2) - Indicates that the trellis coding is disabled Default: enabled(1)
INT hwAdslTransmissionMode	1.3.6.1.2.1.10.94.1.1.14.1.65539	INTEGER	read-create	Indicates the transmission mode of this channel. Options: 1. all(1) - All (G992.1, G992.2, T1.413)(Default) 2. fullRate(2) - Full rate(G992.1 or T1.413) 3. gliteOnly(3) - G992.2(g.lite) only 4. t1413Only(4) - T1.413 only 5. gdmtOnly(5) - G992.1,G992.3,G992.5,(g.dmt) only 6. ghs(6) - g.hs (G992.1,G992.2,G992.3,G992.4,G992.5,G992.5 is prior) 7. g992Dot1(7) - G992.1 8. g992Dot2(8) - G992.2 9. g992Dot3(9) - G992.3 10. g992Dot4(10) - G992.4 11. g992Dot5(11) - G992.5 12. adslAllOnly(12) - ADSL ALL ONLY 13. adslAndAdsl2(13) - G.992.1,G.992.3,T1.413(Not support) Default: all(1)
INT hwadslLineAlarmConfProfileDyingGasp	1.3.6.1.2.1.10.94.1.1.15.1.65536	INTEGER	read-create	This object enables/disables the report of LOSS-OF-POWER alarm in an ADSL line, This object is defaulted enable(1). Options: 1. enable (1) - The LOSS-OF-POWER alarm in an ADSL line will be reported 2. disable (2) - The LOSS-OF-POWER alarm in an ADSL line will not be reported
hwAdslLinePvcTable	1.3.6.1.2.1.10.94.1.1.65536		not-accessible	PVC configuration table of the ADSL port and used to configure the VPI and VCI of the ADSL port. The indexes of this table are ifIndex,hwAdsllinePvcVpi,and hwAdsllinePvcVci. This table is used to configure only the CO PVC.
hwAdslLinePvcEntry	1.3.6.1.2.1.10.94.1.1.65536.1		not-accessible	PVC configuration table of the ADSL port and used to configure the VPI and VCI of the ADSL port. The indexes of this entry are ifIndex,hwAdsllinePvcVpi,and hwAdsllinePvcVci. This table is used to configure only the CO PVC.
I32 hwAdsllinePvcVpi	1.3.6.1.2.1.10.94.1.1.65536.1.1	Integer32	read-only	The VPI of the adsl line.
I32 hwAdslLinePvcVci	1.3.6.1.2.1.10.94.1.1.65536.1.2	Integer32	read-only	The VCI of the adsl line.
I32 hwAdslLinePvcVlanId	1.3.6.1.2.1.10.94.1.1.65536.1.3	Integer32	read-write	The VLAN ID of the adsl line PVC. Range: 1-4000
I32 hwAdslLinePvcPriority	1.3.6.1.2.1.10.94.1.1.65536.1.4	Integer32	read-write	The Priority value of the adsl line PVC. Range: 0-7
I32 hwAdslLinePvcDsBand	1.3.6.1.2.1.10.94.1.1.65536.1.5	Integer32	read-write	The down stream band of the adsl line PVC. Range: 0-450
I32 hwAdslLinePvcUsBand	1.3.6.1.2.1.10.94.1.1.65536.1.6	Integer32	read-write	The up stream band of the adsl line PVC. Range: 0-450
INT hwAdslLinePvcMCastEnable	1.3.6.1.2.1.10.94.1.1.65536.1.7	INTEGER	read-write	This object allows the adsl line PVC to support multicast. Options: 1. enable(1) - Indicates that the PVC of the ADSL port is enabled to support the multicast 2. disable(2) - Indicates that the PVC of the ADSL port is disabled to support the multicast Default: disable(2)
INT hwAdslLinePvcIGMPEnable	1.3.6.1.2.1.10.94.1.1.65536.1.8	INTEGER	read-write	This object allows the adsl line PVC to support IGMP. Options: 1. enable(1) - Indicates that the PVC of the ADSL port is enabled to support IGMP 2. disable(2) - Indicates that the PVC of the ADSL port is disabled to support IGMP Default: disable(2)
I32 hwAdslLinePvcIndex	1.3.6.1.2.1.10.94.1.1.65536.1.9	Integer32	read-write	The index of the adsl line PVC. Range: 1-8
INT hwAdslLinePvcConnectType	1.3.6.1.2.1.10.94.1.1.65536.1.10	INTEGER	read-only	The Connected type of the adsl line PVC. Options: 1. auto(0) - The Connected type of the adsl line PVC is auto 2. llc1483B(1) - The Connected type of the adsl line PVC is llc1483B 3. pppoaLLC(2) - The Connected type of the adsl line PVC is pppoaLLC 4. pppoaVcmux(3) - The Connected type of the adsl line PVC is pppoaVcmux 5. ipoaLLc(4) - The Connected type of the adsl line PVC is ipoaLLc 6. ipoaVcmux(5) - The Connected type of the adsl line PVC is ipoaVcmux
ROW hwAdslLinePvcRowStatus	1.3.6.1.2.1.10.94.1.1.65536.1.11	RowStatus	read-create	Row status. Add or delete a table item.
hwAdslLineBitAllocationTable	1.3.6.1.2.1.10.94.1.1.65537		not-accessible	The hwAdslLineBitAllocationTable contains the detailed bit-allocation information for the current link. This information can be used to determine whether a given sub-carrier loop has sufficient margin to support ADSL data rates, and possibly to determine whether certain specific types of interfe- rence or line attenuation exist.The bit allocation information are only va- lid when the ATU-C is in the C-ACTIVE state. The index of this table is ifIndex.
hwAdslLineBitAllocationEntry	1.3.6.1.2.1.10.94.1.1.65537.1		not-accessible	The hwAdslLineBitAllocationTable contains the detailed bit-allocation information for the current link. This information can be used to determine whether a given sub-carrier loop has sufficient margin to support ADSL data rates, and possibly to determine whether certain specific types of interfe- rence or line attenuation exist.The bit allocation information are only va- lid when the ATU-C is in the C-ACTIVE state. The index of this entry is ifIndex.
I32 hwAdslLineDownStreamBitsPerFrame	1.3.6.1.2.1.10.94.1.1.65537.1.1	Integer32	read-only	Number of bits required per frame in the downstream data path for the current configuration.
I32 hwAdslLineUpStreamBitsPerFrame	1.3.6.1.2.1.10.94.1.1.65537.1.2	Integer32	read-only	Number of bits required per frame in the upstream data path for the current configuration.
OCT hwAdslLineDownStreamBitAllocLow	1.3.6.1.2.1.10.94.1.1.65537.1.3	OCTET STRING	read-only	when used to Adsl board This object contains the first 128 downstream sub-carrier bit allocations (sub-carrier # 1-128). This object is 64 bytes in length, where each byte contains 2 sub-carrier values. Byte 1 - 64 Downstream bit allocation (first 128 sub-carriers), one byte for two sub-carriers. 1 Bits 4 - 7 # bits in 1st downstream sub-carrier 1 Bits 0 - 3 # bits in 2nd downstream sub-carrier ... 64 Bits 4 - 7 # bits in 127th downstream sub-carrier 64 Bits 0 - 3 # bits in 128th downstream sub-carrier when used to Adsl2+ board This object contains the first 256 downstream sub-carrier bit allocations (sub-carrier # 1-256). This object is 256 bytes in length, where each byte contains 1 sub-carrier values. Byte 1 - 256 Downstream bit allocation (first 256 sub-carriers), one byte for one sub-carriers. 1 Bits 0 - 7 # bits in 1st downstream sub-carrier ... 255 Bits 0 - 7 # bits in 255th downstream sub-carrier 256 Bits 0 - 7 # bits in 256th downstream sub-carrier
OCT hwAdslLineDownStreamBitAllocHigh	1.3.6.1.2.1.10.94.1.1.65537.1.4	OCTET STRING	read-only	when used to Adsl board This object contains the second 128 downstream sub-carrier bit allocations (sub-carrier # 129-256). This object is 64 bytes in length, where each byte contains 2 sub-carrier values. Byte 1 - 64 Downstream bit allocation (second 128 sub-carriers), one byte for two sub-carriers. 1 Bits 4 - 7 # bits in 129th downstream sub-carrier 1 Bits 0 - 3 # bits in 130th downstream sub-carrier ... 64 Bits 4 - 7 # bits in 255th downstream sub-carrier 64 Bits 0 - 3 # bits in 256th downstream sub-carrier when used to Adsl2+ board This object contains the second 256 downstream sub-carrier bit allocations (sub-carrier # 257-512). This object is 256 bytes in length, where each byte contains 1 sub-carrier values. Byte 1 - 256 Downstream bit allocation (second 256 sub-carriers), one byte for one sub-carriers. 1 Bits 0 - 7 # bits in 1st downstream sub-carrier ... 255 Bits 0 - 7 # bits in 255th downstream sub-carrier 256 Bits 0 - 7 # bits in 256th downstream sub-carrier
OCT hwAdslLineUpStreamBitAlloc	1.3.6.1.2.1.10.94.1.1.65537.1.5	OCTET STRING	read-only	when used to Adsl board This Object contains 64 upstream sub-carrier bit allocations (sub-carrier # 1-64). This Object is 32 bytes in length, where each byte contains 2 sub-carrier values. Byte 1-32 Upstream bit allocation information, total: 32 bytes, one byte for two sub-carriers. 1 Bits 7 - 4 # bits in 1st upstream sub-carrier 1 Bits 3 - 0 # bits in 2nd upstream sub-carrier ... 32 Bits 7 - 4 # bits in 63rd upstream sub-carrier 32 Bits 3 - 0 # bits in 64th upstream sub-carrier when used to Adsl2+ board This Object contains 64 upstream sub-carrier bit allocations (sub-carrier # 1-64). This Object is 64 bytes in length, where each byte contains 1 sub-carrier values. Byte 1-64 Upstream bit allocation information, total: 64 bytes, one byte for one sub-carriers. 1 Bits 7 - 0 # bits in 1st upstream sub-carrier ... 64 Bits 7 - 0 # bits in 64th upstream sub-carrier
hwXdslPortTable	1.3.6.1.2.1.10.94.1.1.65538		not-accessible	This table includes xDSL(e.g. adsl,g.shdsl,vdsl...)port information, Used to support common attributes of the ADSL, G.SHDSL, and VDSL ports. The index of this table is ifIndex.
hwXdslPortEntry	1.3.6.1.2.1.10.94.1.1.65538.1		not-accessible	This table includes xDSL(e.g. adsl,g.shdsl,vdsl...)port information, Used to support common attributes of the ADSL, G.SHDSL, and VDSL ports. The index of this entry is ifIndex.
I32 hwXdslPortMaxMacLearn	1.3.6.1.2.1.10.94.1.1.65538.1.1	Integer32	read-write	Set Max MAC count on the XDSL port. Range: 0-255 Default: 255
I32 hwXdslPortRateMonitorThreshold	1.3.6.1.2.1.10.94.1.1.65538.1.2	Integer32	read-write	Set Port monitoring rate threshold percent. Including upstream and downstream. Range: 0-100 Default: 0
G32 hwXdslPortUpThresholdTxRate	1.3.6.1.2.1.10.94.1.1.65538.1.4	Gauge32	read-write	Set Port monitoring upstream rate threshold value. Default: 0 Unit: bps
G32 hwXdslPortDownThresholdTxRate	1.3.6.1.2.1.10.94.1.1.65538.1.5	Gauge32	read-write	Set Port monitoring downstream rate threshold value. Default: 0 Unit: bps
INT hwXdslPortRateMonitorAlarmEnable	1.3.6.1.2.1.10.94.1.1.65538.1.6	INTEGER	read-write	Enables/Disables port rate monitor alarm. Options: 1. enabled(1) - The port rate monitor alarm is enabled 2. disabled(2) - The port rate monitor alarm is disabled
C32 hwXdslPortUpTime	1.3.6.1.2.1.10.94.1.1.65538.1.7	Counter32	read-only	Duration of the xDSL port activation. Unit: seconds
INT hwXdslPortNTEPowerStatus	1.3.6.1.2.1.10.94.1.1.65538.1.8	INTEGER	read-only	NTE power status, this object is defaulted off(2). Options: 1. on(1) - NTE power on 2. off(2) - NTE power off 3. unknown(3) - Unknown status
I32 hwXdslPortCurrentUpRate	1.3.6.1.2.1.10.94.1.1.65538.1.500	Integer32	accessible-for-notify	Xdsl Port Current Upstream Value. Range: 0-30000 Default: 0
I32 hwXdslPortCurrentDownRate	1.3.6.1.2.1.10.94.1.1.65538.1.501	Integer32	accessible-for-notify	Xdsl Port Current Downstream Value. Range: 0-30000 Default: 0
INT hwXdslPortFarEndRunState	1.3.6.1.2.1.10.94.1.1.65538.1.600	INTEGER	read-only	Xdsl port far end Run state, This object is defaulted unknown(1). Options: 1. unknown(1) - Unknown status 2. noModem(2) - Port is not connected to modem 3. handshake(3) - Handshake status 4. showtime(4) - Port is activated
INT hwXdslPortPowerState	1.3.6.1.2.1.10.94.1.1.65538.1.601	INTEGER	read-only	Xdsl port power state. Options: 1. l0(1) - Full-on state 2. l2(2) - Low power state 3. l3(3) - Idle state 4. l1(4) - Low power state 5. invalidValue(-1) - Invalid value Default: l0(1)
U32 hwXdslPortUpCnt	1.3.6.1.2.1.10.94.1.1.65538.1.700	Unsigned32	read-only	The up counts of Xdsl port.
INT hwXdslPortUpCntAdminStatus	1.3.6.1.2.1.10.94.1.1.65538.1.701	INTEGER	read-write	Admin the up counts of xDSL port. Options: 1. reset(0) - Reset the up counts of xDSL port
DAT hwXdslPortLastUpTime	1.3.6.1.2.1.10.94.1.1.65538.1.702	DateAndTime	read-only	Last up time of a Xdsl port.
DAT hwXdslPortLastDownTime	1.3.6.1.2.1.10.94.1.1.65538.1.703	DateAndTime	read-only	Last down time of a Xdsl port.
DAT hwXdslPortClearUpCntTime	1.3.6.1.2.1.10.94.1.1.65538.1.704	DateAndTime	read-only	The time when up counts of a Xdsl port is cleared.
U32 hwXdslPortRetrainCnt	1.3.6.1.2.1.10.94.1.1.65538.1.705	Unsigned32	read-only	The retrain counts of Xdsl Line.
U32 hwXdslPortLastRetrainReason	1.3.6.1.2.1.10.94.1.1.65538.1.706	Unsigned32	read-only	The last retrain reson of Xdsl Line, coded as bit mask. Only one bit can be set valid, all bits set valid means invalid retrain reason.
INT hwXdslPortLoopFlag	1.3.6.1.2.1.10.94.1.1.65538.1.800	INTEGER	read-only	Loop flag. Options: 1. false(0) - No loop 2. true (1) - Loop
I32 hwXdslPortUpThreshold	1.3.6.1.2.1.10.94.1.1.65538.1.810	Integer32	read-write	Set Port monitoring upstream rate threshold percent value. Range: 0-100
I32 hwXdslPortDownThreshold	1.3.6.1.2.1.10.94.1.1.65538.1.811	Integer32	read-write	Set Port monitoring downstream rate threshold percent value. Range: 0-100
hwAdslLinePreActParaTable	1.3.6.1.2.1.10.94.1.1.65539		not-accessible	This table provides one row for each ADSL PORT. Each row contains the preactived Parameters. The index of this table is ifIndex.
hwAdslLinePreActParaEntry	1.3.6.1.2.1.10.94.1.1.65539.1		not-accessible	This table provides one row for each ADSL PORT. Each row contains the preactived Parameters. The index of this entry is ifIndex.
I32 hwAdslAtucPrevSnrMgn	1.3.6.1.2.1.10.94.1.1.65539.1.1	Integer32	read-only	Noise Margin as seen by this ATU-C at the time of the last adslAtucRateChangeTrap event. Unit: tenth dB
I32 hwAdslAturPrevSnrMgn	1.3.6.1.2.1.10.94.1.1.65539.1.2	Integer32	read-only	Noise Margin as seen by this ATU-R at the time of the last adslAtucRateChangeTrap event. Unit: tenth dB
U32 hwAdslAtucPrevAttainableRate	1.3.6.1.2.1.10.94.1.1.65539.1.3	Unsigned32	read-only	Indicates the maximum attainable data rate by the ATU-C at the time of the last adslAtucRateChangeTrap event. Unit: bps
U32 hwAdslAturPrevAttainableRate	1.3.6.1.2.1.10.94.1.1.65539.1.4	Unsigned32	read-only	Indicates the maximum attainable data rate by the ATU-R at the time of the last adslAtucRateChangeTrap event. Unit: bps
G32 hwAdslAtucPreAtn	1.3.6.1.2.1.10.94.1.1.65539.1.5	Gauge32	read-only	Measured difference in the total power transmitted as seen by this ATU-C at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
G32 hwAdslAturPreAtn	1.3.6.1.2.1.10.94.1.1.65539.1.6	Gauge32	read-only	Measured difference in the total power transmitted as seen by this ATU-R at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
DAT hwAdslPreActiveTime	1.3.6.1.2.1.10.94.1.1.65539.1.7	DateAndTime	read-only	The last time at that the port was activated.
hwPortThreePriorityTable	1.3.6.1.2.1.10.94.1.1.65540		not-accessible	Adsl port three priority table. The index of this table is ifIndex.
hwPortThreePriorityEntry	1.3.6.1.2.1.10.94.1.1.65540.1		not-accessible	Adsl port three priority table. The index of this entry is ifIndex.
INT hwPortThreePriorityEnable	1.3.6.1.2.1.10.94.1.1.65540.1.1	INTEGER	read-write	Three Priority status of the interface. Options: 1. enable(1) - Adsl port three priority is enabled 2. disable(2) - Adsl port three priority is disabled
hwSlotMacMaxNoLimitTable	1.3.6.1.2.1.10.94.1.1.65541		not-accessible	Max mac learning no limit table. The index of this table is hwFrameIndex and hwSlotIndex.
hwSlotMacMaxNoLimitEntry	1.3.6.1.2.1.10.94.1.1.65541.1		not-accessible	Max mac learning no limit table. The index of this entry is hwFrameIndex and hwSlotIndex.
INT hwSlotMacMaxNoLimitEnable	1.3.6.1.2.1.10.94.1.1.65541.1.1	INTEGER	read-write	This object is used to set whether all the ports in the slot limits the maximum number of learning MAC addresses. Options: 1. enable(1) - Don't limit the max NO. of learning mac addresses in the slot 2. disable(2) - Limit the max NO. of learning mac addresses in the slot
hwXdslPortStateStatisticTable	1.3.6.1.2.1.10.94.1.1.65542		not-accessible	XDSL port state statistic table, used to support the statistics information about the status mapping and status of ports on the service boards, such as the ADSL, G.SHDSL and VDSL boards. The indexes of this table are ifType, hwFrameIndex, and hwSlotIndex.
hwXdslPortStateStatisticEntry	1.3.6.1.2.1.10.94.1.1.65542.1		not-accessible	XDSL port state statistic table, used to support the statistics information about the status mapping and status of ports on the service boards, such as the ADSL, G.SHDSL and VDSL boards. The indexes of this entry are ifType, hwFrameIndex, and hwSlotIndex.
U32 hwXdslPortStatePortNumber	1.3.6.1.2.1.10.94.1.1.65542.1.1	Unsigned32	read-only	This Object is Port Number of One Slot.
OCT hwXdslPortStateBitmapList	1.3.6.1.2.1.10.94.1.1.65542.1.2	OCTET STRING	read-only	The type of port status: 2 failed; 8 testing; 9 activated; 10 activating; 11 deactivated; 18 localloopback; 19 remoteloopback; 20 blocked; 37 utopialoopback; 38 afeloopback; 39 hybridloopback; 255 unknown; HwXdslPortStateBitmapList describes the states of all ports. Every byte describe the current state of every port. The length is equal to the value of the hwXdslPortStatePortNumber.
U32 hwXdslTotalOfActivatedPorts	1.3.6.1.2.1.10.94.1.1.65542.1.3	Unsigned32	read-only	The total of the activated ports.
U32 hwXdslTotalOfDeactivatedPorts	1.3.6.1.2.1.10.94.1.1.65542.1.4	Unsigned32	read-only	The total of the deactivated ports.
U32 hwXdslTotalOfActivatingPorts	1.3.6.1.2.1.10.94.1.1.65542.1.5	Unsigned32	read-only	The total of the activating ports.
U32 hwXdslTotalOfTestingPorts	1.3.6.1.2.1.10.94.1.1.65542.1.6	Unsigned32	read-only	The total of the Testing ports.
U32 hwXdslTotalOfBlockedPorts	1.3.6.1.2.1.10.94.1.1.65542.1.7	Unsigned32	read-only	The total of the blocked ports.
U32 hwXdslTotalOfLocalLoopbackPorts	1.3.6.1.2.1.10.94.1.1.65542.1.8	Unsigned32	read-only	The total of the local testing ports.
U32 hwXdslTotalOfRemoteLoopbackPorts	1.3.6.1.2.1.10.94.1.1.65542.1.9	Unsigned32	read-only	The total of the remote testing ports.
U32 hwXdslTotalOfFailedPorts	1.3.6.1.2.1.10.94.1.1.65542.1.10	Unsigned32	read-only	The total of the failed ports.
U32 hwXdslTotalOfUnknownPorts	1.3.6.1.2.1.10.94.1.1.65542.1.11	Unsigned32	read-only	The total of the unknown testing ports.
hwadslLineExtConfProfileTable	1.3.6.1.2.1.10.94.1.1.65543		not-accessible	This table contains information on the ADSL extend line configuration. One entry in this table reflects a extend line profile defined by a manager which can be used to configure the ADSL line. The index of this table is hwadslLineExtConfProfileName.
hwadslLineExtConfProfileEntry	1.3.6.1.2.1.10.94.1.1.65543.1		not-accessible	This table contains information on the ADSL extend line configuration. One entry in this table reflects a extend line profile defined by a manager which can be used to configure the ADSL line. The index of this entry is hwadslLineExtConfProfileName.
OCT hwadslLineExtConfProfileName	1.3.6.1.2.1.10.94.1.1.65543.1.1	OCTET STRING	not-accessible	This object is used by the hwadslLineExtConfProfileTable in order to identify a row of this table. This object indicates the name of the extended line profile.
I32 hwadslLineDisableToneSection1Begin	1.3.6.1.2.1.10.94.1.1.65543.1.2	Integer32	read-create	The begin index of section1. Range: 0-511
I32 hwadslLineDisableToneSection1End	1.3.6.1.2.1.10.94.1.1.65543.1.3	Integer32	read-create	The end index of section1. Range: 0-511
INT hwadslLineDisableToneSection1Flag	1.3.6.1.2.1.10.94.1.1.65543.1.4	INTEGER	read-create	The enable flag of section1. Options: 1. enabled(1) - The first tone section is enabled 2. disabled(2) - The first tone section is disabled
I32 hwadslLineDisableToneSection2Begin	1.3.6.1.2.1.10.94.1.1.65543.1.5	Integer32	read-create	The begin index of section2. Range: 0-511
I32 hwadslLineDisableToneSection2End	1.3.6.1.2.1.10.94.1.1.65543.1.6	Integer32	read-create	The end index of section2. Range: 0-511
INT hwadslLineDisableToneSection2Flag	1.3.6.1.2.1.10.94.1.1.65543.1.7	INTEGER	read-create	The enable flag of section2. Options: 1. enabled(1) - The second tone section is enabled 2. disabled(2) - The second tone section is disabled
I32 hwadslLineDisableToneSection3Begin	1.3.6.1.2.1.10.94.1.1.65543.1.8	Integer32	read-create	The begin index of section3. Range: 0-511
I32 hwadslLineDisableToneSection3End	1.3.6.1.2.1.10.94.1.1.65543.1.9	Integer32	read-create	The end index of section3. Range: 0-511
INT hwadslLineDisableToneSection3Flag	1.3.6.1.2.1.10.94.1.1.65543.1.10	INTEGER	read-create	The enable flag of the third section. Options: 1. enabled(1) - The third tone section is enabled 2. disabled(2) - The third tone section is disabled
I32 hwadslLineDisableToneSection4Begin	1.3.6.1.2.1.10.94.1.1.65543.1.11	Integer32	read-create	The begin index of the fourth section. Range: 0-511
I32 hwadslLineDisableToneSection4End	1.3.6.1.2.1.10.94.1.1.65543.1.12	Integer32	read-create	The end index of the fourth section. Range: 0-511
INT hwadslLineDisableToneSection4Flag	1.3.6.1.2.1.10.94.1.1.65543.1.13	INTEGER	read-create	The enable flag of the fourth section. Range: 0-511 Options: 1. enabled(1) - The fourth tone section is enabled 2. disabled(2) - The fourth tone section is disabled
HWA hwadsl2ChConfProfMinProtectionDs	1.3.6.1.2.1.10.94.1.1.65543.1.14	HWADSLSYMBOLPROTECTION	read-write	Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection(0), halfSymbol(1), singleSymbol(2), twoSymbols(4), threeSymbols(6), fourSymbols(8), fiveSymbols(10), sixSymbols(12), sevenSymbols(14), eightSymbols(16), nineSymbols(18), tenSymbols(20), elevenSymbols(22), twelveSymbols(24), thirteenSymbols(26), fourteenSymbols(28), fifteenSymbols(30), sixteenSymbols(32), null(65535) The value multiply 1/2 is the real value of Noise Protection values.
HWA hwadsl2ChConfProfMinProtectionUs	1.3.6.1.2.1.10.94.1.1.65543.1.15	HWADSLSYMBOLPROTECTION	read-write	Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection(0), halfSymbol(1), singleSymbol(2), twoSymbols(4), threeSymbols(6), fourSymbols(8), fiveSymbols(10), sixSymbols(12), sevenSymbols(14), eightSymbols(16), nineSymbols(18), tenSymbols(20), elevenSymbols(22), twelveSymbols(24), thirteenSymbols(26), fourteenSymbols(28), fifteenSymbols(30), sixteenSymbols(32), null(65535) The value multiply 1/2 is the real value of Noise Protection values.
I32 hwAdslExtDsMinTrainSnrMgn	1.3.6.1.2.1.10.94.1.1.65543.1.16	Integer32	read-create	Maximum Trainning Margin in downstream. Range: 0-310 Default: 30 Unit: tenth dB
I32 hwAdslExtUsMinTrainSnrMgn	1.3.6.1.2.1.10.94.1.1.65543.1.17	Integer32	read-create	Maximum Trainning Margin in upstream. Range: 0-310 Default: 30 Unit: tenth dB
I32 hwAdslExtDsMaxPsd	1.3.6.1.2.1.10.94.1.1.65543.1.18	Integer32	read-create	Maximum PSD margin in downstream.
ADS hwadsl2TSSiPsdMaskDs	1.3.6.1.2.1.10.94.1.1.65543.1.19	Adsl2PsdMaskDs	read-write	The downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G992.3 or G992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G992.5. This is a string of 32 pairs of values in the following structure: Octets 0-1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 32, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
U32 hwadsl2TranMissionStardardMask	1.3.6.1.2.1.10.94.1.1.65543.1.20	Unsigned32	read-write	The tranmission stardard mask. The Mask bit and the corresponding Transmission Standard: 0x 1 1 1 1 1 1 ETSI T1.413 G992.5 G992.3 G992.2 G992.1 The Default BitMask: 0X0.
U32 hwadsl2TransMissionAnnexMask	1.3.6.1.2.1.10.94.1.1.65543.1.21	Unsigned32	read-write	The transMission annex Mask. The Mask bit and the corresponding Transmission Annex: 0x 1 1 1 1 1 Annex .J Annex .M Annex .L Annex .B Annex .A The Default BitMask: 0X0.
HWA hwadsl2TransMissionAnnexMScope	1.3.6.1.2.1.10.94.1.1.65543.1.22	HWADSL2ANNEXMSCOPE	read-create	Annex M expand scope: 1-Tone Index(7~32) 2-Tone Index(7~36) 3-Tone Index(7~40) 4-Tone Index(7~44) 5-Tone Index(7~48) 6-Tone Index(7~52) 7-Tone Index(7~56) 8-Tone Index(7~60) 9-Tone Index(7~64) -1-invalidValue
INT hwadsl2L2ModeState	1.3.6.1.2.1.10.94.1.1.65543.1.23	INTEGER	read-create	The state of L2 power management mode. Options: 1. disabled(1) - L2 power management mode is disabled 2. enabled(2) - L2 power management mode is enabled 3. forced(3) - L2 power management mode is forced Default: disabled(1)
I32 hwadsl2L2ModeMinDataRate	1.3.6.1.2.1.10.94.1.1.65543.1.24	Integer32	read-create	Minimum Data Rate in L2 Mode. Range: 128-16384 Unit: Kbps
I32 hwadsl2L2ModeMaxDataRate	1.3.6.1.2.1.10.94.1.1.65543.1.25	Integer32	read-create	Maximum Data Rate in L2 Mode. Range: 128-16384 Default: 1024 Unit: Kbps
I32 hwadsl2L2ModePayloadRateThreshold	1.3.6.1.2.1.10.94.1.1.65543.1.26	Integer32	read-create	Threshold for the Payload Rate Ratio. Range: 128-16384 Default: 128 Unit: Kbps
I32 hwadsl2L2ModeGuardTime	1.3.6.1.2.1.10.94.1.1.65543.1.27	Integer32	read-create	Guard Time before entering L2 Mode. Range: 0-1024 Default: 60 Unit: seconds
I32 hwadsl2L2ModeIntervalTime	1.3.6.1.2.1.10.94.1.1.65543.1.28	Integer32	read-create	The minimum interval between two records of L2 mode. Range: 0-255 Default: 255 Unit: seconds
I32 hwadsl2L2ModeIntervalPowerValue	1.3.6.1.2.1.10.94.1.1.65543.1.29	Integer32	read-create	Maximum aggregate transmit power reduction per L2 request or L2 power trim. Range: 0-31 Default: 3 Unit: db
I32 hwadsl2L2ModeTotalPowerValue	1.3.6.1.2.1.10.94.1.1.65543.1.30	Integer32	read-create	Total maximum aggregate transmit power reduction in L2. Range: 0-31 Default: 9 Unit: db
INT hwadslExtUsPhyRcontrol	1.3.6.1.2.1.10.94.1.1.65543.1.31	INTEGER	read-write	To enable or disable the PHY-R function on upstream direction. Options: 1. enable(1) - The PHY-R function on upstream direction is enabled 2. disable(2) - The PHY-R function on upstream direction is disabled Default: disable(2)
ADS hwadslExtUsINPmax	1.3.6.1.2.1.10.94.1.1.65543.1.32	Adsl2SymbolProtection	read-write	Maximum Impulse Noise Protection on upstream direction. The parameter can take the following values: noProtection(1), halfSymbol(2), singleSymbol(3), twoSymbols(4), threeSymbols(5), fourSymbols(6), fiveSymbols(7), sixSymbols(8), sevenSymbols(9), eightSymbols(10), nineSymbols(11), tenSymbols(12), elevenSymbols(13), twelveSymbols(14), thirteeSymbols(15), fourteenSymbols(16), fifteenSymbols(17), sixteenSymbols(18) The value multiply 1/2 is the real value of Noise Protection values. Unit: DMT Symbol Default: 1
I32 hwadslExtUsMinRtxRatio	1.3.6.1.2.1.10.94.1.1.65543.1.33	Integer32	read-write	Minimum rtxratio on upstream direction. Range: 0-255 Default: 0 Unit: 1/256
I32 hwadslExtUsMinRSoverhead	1.3.6.1.2.1.10.94.1.1.65543.1.34	Integer32	read-write	The minimum value of R/N on upstream direction. Range: 0-128 Default: 0 Unit: 1/256
INT hwadslExtDsPhyRcontrol	1.3.6.1.2.1.10.94.1.1.65543.1.35	INTEGER	read-write	To enable or disable the PHY-R function on downstream direction. Options: 1. enable(1) - The PHY-R function on downstream direction is enabled 2. disable(2) - The PHY-R function on downstream direction is disabled Default: disable(2)
ADS hwadslExtDsINPmax	1.3.6.1.2.1.10.94.1.1.65543.1.36	Adsl2SymbolProtection	read-write	Maximum Impulse Noise Protection on downstream direction. The parameter can take the following values: noProtection(1), halfSymbol(2), singleSymbol(3), twoSymbols(4), threeSymbols(5), fourSymbols(6), fiveSymbols(7), sixSymbols(8), sevenSymbols(9), eightSymbols(10), nineSymbols(11), tenSymbols(12), elevenSymbols(13), twelveSymbols(14), thirteeSymbols(15), fourteenSymbols(16), fifteenSymbols(17), sixteenSymbols(18) The value multiply 1/2 is the real value of Noise Protection values. Unit: DMT Symbol
I32 hwadslExtDsMinRtxRatio	1.3.6.1.2.1.10.94.1.1.65543.1.37	Integer32	read-write	Minimum rtxratio on downstream direction. Range: 0-255 Default: 0 Unit: 1/256
I32 hwadslExtDsMinRSoverhead	1.3.6.1.2.1.10.94.1.1.65543.1.38	Integer32	read-write	The minimum value of R/N on downstream direction. Range: 0-128 Default: 0 Unit: 1/256
ADS hwadsl2TSSiPsdMaskUs	1.3.6.1.2.1.10.94.1.1.65543.1.39	Adsl2PsdMaskUs	read-write	The upstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G992.3 or G992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G992.5. This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 9-11, which are associated with a fourth breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCus. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 4, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
INT hwadslLConfProfAdslMode	1.3.6.1.2.1.10.94.1.1.65543.1.40	INTEGER	read-write	The ADSL2 management model specified includes an ADSL Mode attribute which identifies an instance of ADSL Mode-Specific PSD Configuration object in the ADSL Line Profile. The following classes of ADSL operating mode are defined. Options: 1. defMode(1) - ADSL transmit mode is defMode 2. adsl(2) - ADSL transmit mode is adsl 3. adsl2Pots(3) - ADSL transmit mode is adsl2Pots 4. adsl2Isdn(4) - ADSL transmit mode is adsl2Isdn 5. adsl2PlusPots(5) - ADSL transmit mode is adsl2PlusPots 6. adsl2PlusIsdn(6) - ADSL transmit mode is adsl2PlusIsdn 7. adsl2ReachExtended(7) - ADSL transmit mode is adsl2ReachExtended 8. invalidValue(-1) - Invalid value
ROW hwadslLineExtConfProfileRowStatus	1.3.6.1.2.1.10.94.1.1.65543.1.65535	RowStatus	read-create	This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to 'destroy' or 'outOfService') it must be first unreferenced from all associated lines. If the creator of this MIB has chosen not to implement 'dynamic assignment' of profiles, this object's MIN-ACCESS is read-only and its value is always to be 'active'.
I32 hwadsl2L2ModeL2Time	1.3.6.1.2.1.10.94.1.1.65543.1.65536	Integer32	read-create	This minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. It ranges from 0 to 255 seconds. Range: 0-255 Default: 30 Unit: seconds
hwAdslLineLatestActParaTable	1.3.6.1.2.1.10.94.1.1.65544		not-accessible	This table provides one row for each ADSL PORT. Each row contains the latest actived Parameters. The index of this table is ifIndex.
hwAdslLineLatestActParaEntry	1.3.6.1.2.1.10.94.1.1.65544.1		not-accessible	This table provides one row for each ADSL PORT. Each row contains the latest actived Parameters. The index of this entry is ifIndex.
DAT hwAdslLineLatestActiveTime	1.3.6.1.2.1.10.94.1.1.65544.1.1	DateAndTime	read-only	Actual time when latest actived.
DAT hwAdslLineLatestDeactiveTime	1.3.6.1.2.1.10.94.1.1.65544.1.2	DateAndTime	read-only	Actual time when latest deactived. If port is actived, the value is invalid.
G32 hwAdslAtucLatestTxRate	1.3.6.1.2.1.10.94.1.1.65544.1.3	Gauge32	read-only	Actual transmit rate on this channel when latest actived. Unit: bps
G32 hwAdslAturLatestTxRate	1.3.6.1.2.1.10.94.1.1.65544.1.4	Gauge32	read-only	Actual transmit rate on this channel when latest actived. Unit: bps
I32 hwAdslAtucLatestSnrMgn	1.3.6.1.2.1.10.94.1.1.65544.1.5	Integer32	read-only	Noise Margin as seen by this ATU-C at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
I32 hwAdslAturLatestSnrMgn	1.3.6.1.2.1.10.94.1.1.65544.1.6	Integer32	read-only	Noise Margin as seen by this ATU-R at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
G32 hwAdslAtucLatestAtn	1.3.6.1.2.1.10.94.1.1.65544.1.7	Gauge32	read-only	Measured difference in the total power transmitted as seen by this ATU-C at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
G32 hwAdslAturLatestAtn	1.3.6.1.2.1.10.94.1.1.65544.1.8	Gauge32	read-only	Measured difference in the total power transmitted as seen by this ATU-R at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
G32 hwAdslAtucLatestAttainableRate	1.3.6.1.2.1.10.94.1.1.65544.1.9	Gauge32	read-only	Indicates the maximum attainable data rate by the ATU-C at the time of the last adslAtucRateChangeTrap event. Unit: bps
G32 hwAdslAturLatestAttainableRate	1.3.6.1.2.1.10.94.1.1.65544.1.10	Gauge32	read-only	Indicates the maximum attainable data rate by the ATU-R at the time of the last adslAtucRateChangeTrap event. Unit: bps
G32 hwAdslAtucLatestConfTxRate	1.3.6.1.2.1.10.94.1.1.65544.1.11	Gauge32	read-only	Configured transmit rate for ADSL port, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates. Unit: bps
G32 hwAdslAturLatestConfTxRate	1.3.6.1.2.1.10.94.1.1.65544.1.12	Gauge32	read-only	Configured receive rate for ADSL port, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates. Unit: bps
G32 hwAdslAtucLatestInterleaveDelay	1.3.6.1.2.1.10.94.1.1.65544.1.13	Gauge32	read-only	Interleave Delay for this channel when latest actived. Unit: milliseconds
G32 hwAdslAturLatestInterleaveDelay	1.3.6.1.2.1.10.94.1.1.65544.1.14	Gauge32	read-only	Interleave Delay for this channel when latest actived. Unit: milliseconds
I32 hwAdslAtucLatestTargetSnrMgn	1.3.6.1.2.1.10.94.1.1.65544.1.15	Integer32	read-only	Port Signal/Noise Margin. Range: 0-310 Unit: tenth dB
I32 hwAdslAturLatestTargetSnrMgn	1.3.6.1.2.1.10.94.1.1.65544.1.16	Integer32	read-only	Port Signal/Noise Margin. Range: 0-310 Unit: tenth dB
G32 hwAdslAtucLatestTxRateThreshold	1.3.6.1.2.1.10.94.1.1.65544.1.17	Gauge32	read-only	Port down stream threshold. Unit: bps
G32 hwAdslAturLatestTxRateThreshold	1.3.6.1.2.1.10.94.1.1.65544.1.18	Gauge32	read-only	Port up stream threshold. Unit: bps
hwXdslPortPerformanceStatTable	1.3.6.1.2.1.10.94.1.1.65545		not-accessible	XDSL port performance statistic table. The indexes of this table are ifIndex and hwXdslPort15minutesPerformanceInterval.
hwXdslPortPerformanceStatEntry	1.3.6.1.2.1.10.94.1.1.65545.1		not-accessible	XDSL port performance statistic table. The indexes of this entry are ifIndex and hwXdslPort15minutesPerformanceInterval.
I32 hwXdslPort15minutesPerformanceInterval	1.3.6.1.2.1.10.94.1.1.65545.1.1	Integer32	not-accessible	The index of the interval which is queried. Range: 0-96
C32 hwXdslPort15minutesPerformanceInBytes	1.3.6.1.2.1.10.94.1.1.65545.1.2	Counter32	read-only	Read the receive bytes of xDSL port during 15 minutes.
C32 hwXdslPort15minutesPerformanceOutBytes	1.3.6.1.2.1.10.94.1.1.65545.1.3	Counter32	read-only	Read the transmit bytes of xDSL port during 15 minutes.
C32 hwXdslPortSyncSuccNumber	1.3.6.1.2.1.10.94.1.1.65545.1.4	Counter32	read-only	Number of successful activations of the xDSL port within 15 minutes.
C32 hwXdslPortSyncFailNumber	1.3.6.1.2.1.10.94.1.1.65545.1.5	Counter32	read-only	Number of failed activations of the xDSL port within 15 minutes.
C32 hwXdslPortAtucCodeViolation	1.3.6.1.2.1.10.94.1.1.65545.1.6	Counter32	read-only	Number of head errors of the ATUC cell within 15 minutes.
C32 hwXdslPortAturCodeViolation	1.3.6.1.2.1.10.94.1.1.65545.1.7	Counter32	read-only	Number of head errors of the ATUR cell within 15 minutes.
C32 hwXdslPortAtucFecSeconds	1.3.6.1.2.1.10.94.1.1.65545.1.8	Counter32	read-only	Seconds of the ATUC FEC errors within 15 minutes.
C32 hwXdslPortAturFecSeconds	1.3.6.1.2.1.10.94.1.1.65545.1.9	Counter32	read-only	Seconds of the ATUR FEC errors within 15 minutes.
C32 hwXdslPortCurrent15minutesStatTime	1.3.6.1.2.1.10.94.1.1.65545.1.10	Counter32	read-only	Seconds passed within the current 15 minutes.
hwAdslPortPerformanceStatTable	1.3.6.1.2.1.10.94.1.1.65546		not-accessible	This table is used to describe the performance statistics of the ADSL port within 15 minutes. The indexes of this table are ifIndex and hwAdslPort15minutesPerformanceInterval.
hwAdslPortPerformanceStatEntry	1.3.6.1.2.1.10.94.1.1.65546.1		not-accessible	This table is used to describe the performance statistics of the ADSL port within 15 minutes. The indexes of this entry are ifIndex and hwAdslPort15minutesPerformanceInterval.
I32 hwAdslPort15minutesPerformanceInterval	1.3.6.1.2.1.10.94.1.1.65546.1.1	Integer32	not-accessible	The index of the interval which is queried. Range: 0-96
C32 hwAdslPort15minutesPerformanceInBytes	1.3.6.1.2.1.10.94.1.1.65546.1.2	Counter32	read-only	Read the receive bytes of xDSL port during 15 minutes.
C32 hwAdslPort15minutesPerformanceOutBytes	1.3.6.1.2.1.10.94.1.1.65546.1.3	Counter32	read-only	Read the transmit bytes of xDSL port during 15 minutes.
C32 hwAdslPortSyncSuccNumber	1.3.6.1.2.1.10.94.1.1.65546.1.4	Counter32	read-only	Number of successful activations within 15 minutes.
C32 hwAdslPortSyncFailNumber	1.3.6.1.2.1.10.94.1.1.65546.1.5	Counter32	read-only	Number of failed activations within 15 minutes.
C32 hwAdslPortAtucCodeViolation	1.3.6.1.2.1.10.94.1.1.65546.1.6	Counter32	read-only	Seconds of head errors of the ATUC cell within 15 minutes.
C32 hwAdslPortAturCodeViolation	1.3.6.1.2.1.10.94.1.1.65546.1.7	Counter32	read-only	Seconds of head errors of the ATUC cell within 15 minutes.
C32 hwAdslPortAtucFecSeconds	1.3.6.1.2.1.10.94.1.1.65546.1.8	Counter32	read-only	Seconds of the ATUC FEC errors within 15 minutes.
C32 hwAdslPortAturFecSeconds	1.3.6.1.2.1.10.94.1.1.65546.1.9	Counter32	read-only	Error seconds of the ATUR FEC within 15 minutes.
C32 hwAdslPortCurrent15minutesTimeElapse	1.3.6.1.2.1.10.94.1.1.65546.1.10	Counter32	read-only	Seconds that is passed within the current 15 minutes.
C32 hwAdslPortAtucHecDropCellsCnt	1.3.6.1.2.1.10.94.1.1.65546.1.11	Counter32	read-only	ATUC cells discarded with HEC Errors.
C32 hwAdslPortAturHecDropCellsCnt	1.3.6.1.2.1.10.94.1.1.65546.1.12	Counter32	read-only	ATUR cells discarded with HEC Errors.
OCT hwAdslLineConfProfile	1.3.6.1.2.1.10.94.1.1.65546.1.13	OCTET STRING	read-only	The value of this object identifies the row in the ADSL Line Configuration Profile Table, (adslLineConfProfileTable), which applies for this ADSL line, and channels if applicable. For 'dynamic' mode, in the case which the configuration profile has not been set, the value will be set to 'DEFVAL'. If the creator of this MIB has chosen not to implement 'dynamic assignment' of profiles, this object's MIN-ACCESS is read-only.
C32 hwAdslPort15minUpTime	1.3.6.1.2.1.10.94.1.1.65546.1.14	Counter32	read-only	Up time in the interval. Unit: seconds
G32 hwAdslAtucCurrAtn	1.3.6.1.2.1.10.94.1.1.65546.1.15	Gauge32	read-only	Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU. Range: 0-630 Unit: tenth dB
I32 hwAdslAtucCurrSnrMgn	1.3.6.1.2.1.10.94.1.1.65546.1.16	Integer32	read-only	Noise Margin as seen by this ATU with respect to its received signal in tenth dB. Unit: tenth dB
G32 hwAdslAtucCurrAttainableRate	1.3.6.1.2.1.10.94.1.1.65546.1.17	Gauge32	read-only	Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate. Unit: bps
G32 hwAdslAtucChanCurrTxRate	1.3.6.1.2.1.10.94.1.1.65546.1.18	Gauge32	read-only	Actual transmit rate on this channel. Unit: bps
G32 hwAdslAturCurrAtn	1.3.6.1.2.1.10.94.1.1.65546.1.19	Gauge32	read-only	Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU. Range: 0-630 Unit: tenth dB
I32 hwAdslAturCurrSnrMgn	1.3.6.1.2.1.10.94.1.1.65546.1.20	Integer32	read-only	Noise Margin as seen by this ATU with respect to its received signal in tenth dB. Unit: tenth dB
G32 hwAdslAturCurrAttainableRate	1.3.6.1.2.1.10.94.1.1.65546.1.21	Gauge32	read-only	Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate. Unit: bps
G32 hwAdslAturChanCurrTxRate	1.3.6.1.2.1.10.94.1.1.65546.1.22	Gauge32	read-only	Actual transmit rate on this channel. Unit: bps
NUM hwAdslAtucIntervalESs	1.3.6.1.2.1.10.94.1.1.65546.1.23	PerfIntervalCount	read-only	Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects. Unit: seconds
NUM hwAdslAtucIntervalLofs	1.3.6.1.2.1.10.94.1.1.65546.1.24	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Framing. Unit: seconds
NUM hwAdslAtucIntervalLols	1.3.6.1.2.1.10.94.1.1.65546.1.25	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Link. Unit: seconds
NUM hwAdslAtucIntervalLoss	1.3.6.1.2.1.10.94.1.1.65546.1.26	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Signal. Unit: seconds
NUM hwAdslAtucIntervalLprs	1.3.6.1.2.1.10.94.1.1.65546.1.27	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Power. Unit: seconds
NUM hwAdslAturIntervalESs	1.3.6.1.2.1.10.94.1.1.65546.1.28	PerfIntervalCount	read-only	Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects. Unit: seconds
NUM hwAdslAturIntervalLofs	1.3.6.1.2.1.10.94.1.1.65546.1.29	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Framing. Unit: seconds
NUM hwAdslAturIntervalLoss	1.3.6.1.2.1.10.94.1.1.65546.1.30	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Signal. Unit: seconds
NUM hwAdslAturIntervalLprs	1.3.6.1.2.1.10.94.1.1.65546.1.31	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Power. Unit: seconds
NUM hwAdslAtucChanIntervalReceivedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.32	PerfIntervalCount	read-only	Count of all encoded blocks received on this channel during this interval.
NUM hwAdslAtucChanIntervalTransmittedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.33	PerfIntervalCount	read-only	Count of all encoded blocks transmitted on this channel during this interval.
NUM hwAdslAtucChanIntervalCorrectedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.34	PerfIntervalCount	read-only	Count of all blocks received with errors that were corrected on this channel during this interval.
NUM hwAdslAtucChanIntervalUncorrectBlks	1.3.6.1.2.1.10.94.1.1.65546.1.35	PerfIntervalCount	read-only	Count of all blocks received with uncorrectable errors on this channel during this interval.
NUM hwAdslAturChanIntervalReceivedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.36	PerfIntervalCount	read-only	Count of all encoded blocks received on this channel during this interval.
NUM hwAdslAturChanIntervalTransmittedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.37	PerfIntervalCount	read-only	Count of all encoded blocks transmitted on this channel during this interval.
NUM hwAdslAturChanIntervalCorrectedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.38	PerfIntervalCount	read-only	Count of all blocks received with errors that were corrected on this channel during this interval.
NUM hwAdslAturChanIntervalUncorrectBlks	1.3.6.1.2.1.10.94.1.1.65546.1.39	PerfIntervalCount	read-only	Count of all blocks received with uncorrectable errors on this channel during this interval.
NUM hwAdslAtucIntervalSesL	1.3.6.1.2.1.10.94.1.1.65546.1.40	PerfIntervalCount	read-only	For the each interval, adslAtucIntervalSesL reports the number of seconds during which there have been severely errored seconds-line. Unit: seconds
NUM hwAdslAtucIntervalUasL	1.3.6.1.2.1.10.94.1.1.65546.1.41	PerfIntervalCount	read-only	For the each interval, adslAtucIntervalUasL reports the number of seconds during which there have been unavailable seconds-line. Unit: seconds
NUM hwAdslAturIntervalSesL	1.3.6.1.2.1.10.94.1.1.65546.1.42	PerfIntervalCount	read-only	For the each interval, adslAturIntervalSesL reports the number of seconds during which there have been severely errored seconds-line. Unit: seconds
NUM hwAdslAturIntervalUasL	1.3.6.1.2.1.10.94.1.1.65546.1.43	PerfIntervalCount	read-only	For the each interval, adslAturIntervalUasL reports the number of seconds during which there have been unavailable seconds-line. Unit: seconds
INT hwAdslPortCurrentActMode	1.3.6.1.2.1.10.94.1.1.65546.1.44	INTEGER	read-only	Instantaneous value of the technology type that line is currently trained up under. Options: 1. adsl(1) - Indicates that line is currently trained up under adsl type 2. adsl2(2) - Indicates that line is currently trained up under adsl2 type 3. adsl2plus(3) - Indicates that line is currently trained up under adsl2+ type
hwAdslPortRateChangeTrapParaTable	1.3.6.1.2.1.10.94.1.1.65547		not-accessible	ADSL line rate change trap parameter table. The index of this table is ifIndex.
hwAdslPortRateChangeTrapParaEntry	1.3.6.1.2.1.10.94.1.1.65547.1		not-accessible	ADSL line rate change trap parameter table. The index of this entry is ifIndex.
OCT hwAdslPortRateChangeTrapIPIAID	1.3.6.1.2.1.10.94.1.1.65547.1.1	OCTET STRING	accessible-for-notify	The port IPIAID is reported when the port rate changes.
OCT hwAdslPortRateChangeTrapMUXID	1.3.6.1.2.1.10.94.1.1.65547.1.2	OCTET STRING	accessible-for-notify	The port MUXID is reported when the port rate changes.
C32 hwAdslPortRateChangeTrapTimeStamp	1.3.6.1.2.1.10.94.1.1.65547.1.3	Counter32	accessible-for-notify	The time stamp of Line rate change trap. Standard Unix format; as the number of seconds since 1/1/1970 (UNIT:Second).
G32 hwAdslPortRateChangeTrapDSLineRate	1.3.6.1.2.1.10.94.1.1.65547.1.4	Gauge32	accessible-for-notify	Down stream line rate after line rate change.
G32 hwAdslPortRateChangeTrapUSLineRate	1.3.6.1.2.1.10.94.1.1.65547.1.5	Gauge32	accessible-for-notify	Up stream line rate after line rate change.
OCT hwAdslPortRateChangeTrapEventType	1.3.6.1.2.1.10.94.1.1.65547.1.6	OCTET STRING	accessible-for-notify	Event type reported during the previous change of the rate. If both the upstream and downstream rates change, this leaf object outputs character string 'DU'. If only the upstream rates changes, this leaf object outputs character string 'US'. If only the downstream rates changes, this leaf object outputs character string 'DS'.
OCT hwAdslPortRateChangeTrapDslType	1.3.6.1.2.1.10.94.1.1.65547.1.7	OCTET STRING	accessible-for-notify	DSL line type of the port whose rate changes.
hwXdslSysManagementParaTable	1.3.6.1.2.1.10.94.1.1.65548
INT hwAdslPortRateChangeTrapConfig	1.3.6.1.2.1.10.94.1.1.65548.1	INTEGER	read-write	Enable or disable ADSL port line-rate change trap feature. Options: 1. enabled(1) - ADSL port line-rate change trap feature is enabled 2. disabled(2) - ADSL port line-rate change trap feature is disabled
hwAdsl2SCStateTable	1.3.6.1.2.1.10.94.1.1.65549		not-accessible	The table adsl2SCStatusTable contains status parameters of the ADSL2 sub-carriers. The indexes of this table are ifIndex and hwAdsl2SCStatusDirection.
hwAdsl2SCStatusEntry	1.3.6.1.2.1.10.94.1.1.65549.1		not-accessible	The table adsl2SCStatusTable contains status parameters of the ADSL2 sub-carriers. The indexes of this entry are ifIndex and hwAdsl2SCStatusDirection.
INT hwAdsl2SCStatusDirection	1.3.6.1.2.1.10.94.1.1.65549.1.1	INTEGER	not-accessible	The direction of the sub-carrier is either upstream or downstream. Options: 1. upstream(1) - Upstream sub-carrier 2. downstream(2) - Downstream sub-carrier
OCT hwAdsl2SCStatusSnr	1.3.6.1.2.1.10.94.1.1.65549.1.2	OCTET STRING	read-only	The SNR Margin per sub-carrier, expressing the ratio between the received signal power and received noise power per subscriber. It is an array of 512 octets, designed for supporting up to 512 (downstream) sub-carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Octet i (0 <= i < NSC) is set to a value in the range 0 to 254 to indicate that the respective downstream or upstream sub- carrier i has SNR of: (-32 + Adsl2SubcarrierSnr(i)/2) in dB (i.e., -32 to 95dB). The special value 255 means that no measurement could be done for the subcarrier because it is out of the PSD mask passband or that the noise PSD is out of range to be represented. Each value in this array is 8 bits wide.
OCT hwAdsl2SCStatusBitsAlloc	1.3.6.1.2.1.10.94.1.1.65549.1.3	OCTET STRING	read-only	The bits allocation per sub-carrier. An array of 256 octets (512 nibbles), designed for supporting up to 512 (downstream) sub-carriers. The number of utilized nibbles on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Nibble i (0 <= i < NSC) is set to a value in the range 0 to 15 to indicate that the respective downstream or upstream sub-carrier i has the same amount of bits allocation.
OCT hwAdsl2SCStatusGainAlloc	1.3.6.1.2.1.10.94.1.1.65549.1.4	OCTET STRING	read-only	The gain allocation per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Value i (0 <= i < NSC) is in the range 0 to 4093 to indicate that the respective downstream or upstream sub-carrier i has the same amount of gain value. The gain value is represented as a multiple of 1/512 on a linear scale. Each value in this array is 16 bits wide and is stored in big endian format.
OCT hwAdsl2SCStatusLog	1.3.6.1.2.1.10.94.1.1.65549.1.5	OCTET STRING	read-only	An array of up to 512 real H(f) logarithmic representation values in dB for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Each array entry represents the real Hlog(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NSC). The real Hlog(f) value is represented as (6-m(i)/10), with m(i) in the range 0 to 1022. A special value m=1023 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 16 bits wide and is stored in big endian format.
OCT hwAdsl2SCStatusQln	1.3.6.1.2.1.10.94.1.1.65549.1.6	OCTET STRING	read-only	An array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Each array entry represents the QLN(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NSC). The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the range 0 to 254. A special value n(i)=255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the noise PSD is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 8 bits wide.
OCT hwAdsl2SCStatusSnrMargin	1.3.6.1.2.1.10.94.1.1.65549.1.7	OCTET STRING	read-only	SNR Margin is the maximum increase in dB of the noise power received at the ATU (ATU-R on downstream direction and ATU-C on upstream direction), such that the BER requirements are met for all bearer channels received at the ATU. It ranges from -640 to 630 units of 0.1 dB (physical values are -64 to 63 dB).
OCT hwAdsl2SCStatusTxPSD	1.3.6.1.2.1.10.94.1.1.65549.1.8	OCTET STRING	read-only	The PSD MASK per sub-carrier.An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub-carriers. It ranges from -1400 to -300 units of 0.1 dBm/Hz (physical values are -140 to -30 dBm/Hz).
hwxdslDynamicProfTable	1.3.6.1.2.1.10.94.1.1.65550		not-accessible	This table includes common parameters of the xdsl Dynamic profile. The index of this table is hwxdslDynamicProfProfileName.
hwxdslDynamicProfEntry	1.3.6.1.2.1.10.94.1.1.65550.1		not-accessible	This table includes common parameters of the xdsl Dynamic profile. The index of this entry is hwxdslDynamicProfProfileName.
OCT hwxdslDynamicProfProfileName	1.3.6.1.2.1.10.94.1.1.65550.1.1	OCTET STRING	not-accessible	The name of xdsl Dynamic Profile.
BIT hwxdslDynamicProfXtuTransSysEna	1.3.6.1.2.1.10.94.1.1.65550.1.2	Bits	read-create	Xtu Transmission System Enabling (ATSE). A list of the different coding types enabled in this profile. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the XTUs may apply the respective coding for the XDSL line. A bit set to '0' means that the XTUs cannot apply the respective coding for the XDSL line. All 'reserved' bits should be set to '0'.
INT hwxdslDynamicProfBitSwapDS	1.3.6.1.2.1.10.94.1.1.65550.1.3	INTEGER	read-create	Enables or disables the bit swap downstream of a line. Options: 1. disable(1) - The bit swap downstream of a line is disabled 2. enable(2) - The bit swap downstream of a line is enabled 3. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfBitSwapUS	1.3.6.1.2.1.10.94.1.1.65550.1.4	INTEGER	read-create	Enables or disables the bit swap upstream of a line. Options: 1. disable(1) - The bit swap upstream of a line is disabled 2. enable(2) - The bit swap upstream of a line is enabled 3. invalidValue(-1) - Invalid value
U32 hwxdslDynamicProfTargetSnrmDs	1.3.6.1.2.1.10.94.1.1.65550.1.5	Unsigned32	read-create	The target Noise Margin the xTU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
U32 hwxdslDynamicProfTargetSnrmUs	1.3.6.1.2.1.10.94.1.1.65550.1.6	Unsigned32	read-create	The target Noise Margin the xTU-C receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
U32 hwxdslDynamicProfMaxSnrmDs	1.3.6.1.2.1.10.94.1.1.65550.1.7	Unsigned32	read-create	The maximum Noise Margin the xTU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
U32 hwxdslDynamicProfMaxSnrmUs	1.3.6.1.2.1.10.94.1.1.65550.1.8	Unsigned32	read-create	The maximum Noise Margin the xTU-C receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
U32 hwxdslDynamicProfMinSnrmDs	1.3.6.1.2.1.10.94.1.1.65550.1.9	Unsigned32	read-create	The minimum Noise Margin the xTU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
U32 hwxdslDynamicProfMinSnrmUs	1.3.6.1.2.1.10.94.1.1.65550.1.10	Unsigned32	read-create	The minimum Noise Margin the xTU-C receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
INT hwxdslDynamicProfCh1MinProtectionDs	1.3.6.1.2.1.10.94.1.1.65550.1.11	INTEGER	read-create	Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Options: 1. noProtection (1) - Indicates that the INP value is 0 2. halfSymbol (2) - Indicates that the INP value is 0.5 3. singleSymbol (3) - Indicates that the INP value is 1 4. twoSymbols (4) - Indicates that the INP value is 2 5. threeSymbols (5) - Indicates that the INP value is 3 6. fourSymbols (6) - Indicates that the INP value is 4 7. fiveSymbols (7) - Indicates that the INP value is 5 8. sixSymbols (8) - Indicates that the INP value is 6 9. sevenSymbols (9) - Indicates that the INP value is 7 10. eightSymbols (10) - Indicates that the INP value is 8 11. nineSymbols (11) - Indicates that the INP value is 9 12. tenSymbols (12) - Indicates that the INP value is 10 13. elevenSymbols (13) - Indicates that the INP value is 11 14. twelveSymbols (14) - Indicates that the INP value is 12 15. thirteenSymbols (15) - Indicates that the INP value is 13 16. fourteenSymbols (16) - Indicates that the INP value is 14 17. fifteenSymbols (17) - Indicates that the INP value is 15 18. sixteenSymbols (18) - Indicates that the INP value is 16 19. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfCh1MinProtectionUs	1.3.6.1.2.1.10.94.1.1.65550.1.12	INTEGER	read-create	Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Options: 1. noProtection (1) - Indicates that the INP value is 0 2. halfSymbol (2) - Indicates that the INP value is 0.5 3. singleSymbol (3) - Indicates that the INP value is 1 4. twoSymbols (4) - Indicates that the INP value is 2 5. threeSymbols (5) - Indicates that the INP value is 3 6. fourSymbols (6) - Indicates that the INP value is 4 7. fiveSymbols (7) - Indicates that the INP value is 5 8. sixSymbols (8) - Indicates that the INP value is 6 9. sevenSymbols (9) - Indicates that the INP value is 7 10. eightSymbols (10) - Indicates that the INP value is 8 11. nineSymbols (11) - Indicates that the INP value is 9 12. tenSymbols (12) - Indicates that the INP value is 10 13. elevenSymbols (13) - Indicates that the INP value is 11 14. twelveSymbols (14) - Indicates that the INP value is 12 15. thirteenSymbols (15) - Indicates that the INP value is 13 16. fourteenSymbols (16) - Indicates that the INP value is 14 17. fifteenSymbols (17) - Indicates that the INP value is 15 18. sixteenSymbols (18) - Indicates that the INP value is 16 19. invalidValue(-1) - Invalid value
U32 hwxdslDynamicProfCh1MaxDelayDs	1.3.6.1.2.1.10.94.1.1.65550.1.13	Unsigned32	read-create	Maximum Interleave Delay on Downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay is as close as possible to, but less than or equal to, hwxdslDynamicProfCh1MaxDelayDs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Range: 0-200 Unit: milliseconds
U32 hwxdslDynamicProfCh1MaxDelayUs	1.3.6.1.2.1.10.94.1.1.65550.1.14	Unsigned32	read-create	Maximum Interleave Delay on Upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay is as close as possible to, but less than or equal to, hwxdslDynamicProfCh1MaxDelayUs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Range: 0-200 Unit: milliseconds
INT hwxdslDynamicProfCh2MinProtectionDs	1.3.6.1.2.1.10.94.1.1.65550.1.15	INTEGER	read-create	Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Options: 1. noProtection (1) - Indicates that the INP value is 0 2. halfSymbol (2) - Indicates that the INP value is 0.5 3. singleSymbol (3) - Indicates that the INP value is 1 4. twoSymbols (4) - Indicates that the INP value is 2 5. threeSymbols (5) - Indicates that the INP value is 3 6. fourSymbols (6) - Indicates that the INP value is 4 7. fiveSymbols (7) - Indicates that the INP value is 5 8. sixSymbols (8) - Indicates that the INP value is 6 9. sevenSymbols (9) - Indicates that the INP value is 7 10. eightSymbols (10) - Indicates that the INP value is 8 11. nineSymbols (11) - Indicates that the INP value is 9 12. tenSymbols (12) - Indicates that the INP value is 10 13. elevenSymbols (13) - Indicates that the INP value is 11 14. twelveSymbols (14) - Indicates that the INP value is 12 15. thirteenSymbols (15) - Indicates that the INP value is 13 16. fourteenSymbols (16) - Indicates that the INP value is 14 17. fifteenSymbols (17) - Indicates that the INP value is 15 18. sixteenSymbols (18) - Indicates that the INP value is 16 19. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfCh2MinProtectionUs	1.3.6.1.2.1.10.94.1.1.65550.1.16	INTEGER	read-create	Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Options: 1. noProtection (1) - Indicates that the INP value is 0 2. halfSymbol (2) - Indicates that the INP value is 0.5 3. singleSymbol (3) - Indicates that the INP value is 1 4. twoSymbols (4) - Indicates that the INP value is 2 5. threeSymbols (5) - Indicates that the INP value is 3 6. fourSymbols (6) - Indicates that the INP value is 4 7. fiveSymbols (7) - Indicates that the INP value is 5 8. sixSymbols (8) - Indicates that the INP value is 6 9. sevenSymbols (9) - Indicates that the INP value is 7 10. eightSymbols (10) - Indicates that the INP value is 8 11. nineSymbols (11) - Indicates that the INP value is 9 12. tenSymbols (12) - Indicates that the INP value is 10 13. elevenSymbols (13) - Indicates that the INP value is 11 14. twelveSymbols (14) - Indicates that the INP value is 12 15. thirteenSymbols (15) - Indicates that the INP value is 13 16. fourteenSymbols (16) - Indicates that the INP value is 14 17. fifteenSymbols (17) - Indicates that the INP value is 15 18. sixteenSymbols (18) - Indicates that the INP value is 16 19. invalidValue(-1) - Invalid value
U32 hwxdslDynamicProfCh2MaxDelayDs	1.3.6.1.2.1.10.94.1.1.65550.1.17	Unsigned32	read-create	Maximum Interleave Delay on Downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay is as close as possible to, but less than or equal to, hwxdslDynamicProfCh2MaxDelayDs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Range: 0-200 Unit: milliseconds
U32 hwxdslDynamicProfCh2MaxDelayUs	1.3.6.1.2.1.10.94.1.1.65550.1.18	Unsigned32	read-create	Maximum Interleave Delay on Upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay is as close as possible to, but less than or equal to, hwxdslDynamicProfCh2MaxDelayUs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Range: 0-200 Unit: milliseconds
BIT hwxdslDynamicProfPmMode	1.3.6.1.2.1.10.94.1.1.65550.1.19	Bits	read-create	Power management state Enabling. Defines the power states the xTU-C or xTU-R may autonomously transition to on this line. The various bit positions are: allowTransitionsToIdle (0) and allowTransitionsToLowPower (1). A bit with a '1' value means that the xTU is allowed to transit into the respective state and a '0' value means that the xTU is not allowed to transit into the respective state.
U32 hwxdslDynamicProfL0Time	1.3.6.1.2.1.10.94.1.1.65550.1.20	Unsigned32	read-create	This minimum time (in seconds) between an Exit from the L2 state and the next Entry into the L2 state. It ranges from 0 to 255 seconds. Range: 0-255
U32 hwxdslDynamicProfL2Time	1.3.6.1.2.1.10.94.1.1.65550.1.21	Unsigned32	read-create	This minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. It ranges from 0 to 255 seconds. Range: 0-255
U32 hwxdslDynamicProfL2Atpr	1.3.6.1.2.1.10.94.1.1.65550.1.22	Unsigned32	read-create	The maximum aggregate transmit power reduction (in dB) that can be performed at transition of L0 to L2 state or through a single Power Trim in the L2 state. It ranges from 0 dB to 31 dB. Range: 0-31 Unit: dB
U32 hwxdslDynamicProfL2Atprt	1.3.6.1.2.1.10.94.1.1.65550.1.23	Unsigned32	read-create	The total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Request (i.e., at transition of L0 to L2 state) and Power Trims. Range: 0-31 Unit: dB
OCT hwxdslDynamicProfDpboEPsd	1.3.6.1.2.1.10.94.1.1.65550.1.24	OCTET STRING	read-create	This parameter defines the PSD mask that is assumed to be permitted at the exchange. This parameter shall use the same format as PSDMASKds. The maximum number of breakpoints for DPBOEPSD is 16. This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value 0xff.
U32 hwxdslDynamicProfDpboEsEL	1.3.6.1.2.1.10.94.1.1.65550.1.25	Unsigned32	read-create	This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back-off depending on this length. For this parameter the electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. DPBOESEL shall be coded as an unsigned integer representing an electrical length from 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB. All values in the range are valid.If DPBOESEL is set to zero, the DPBO in this section shall be disabled. Range: 0-511 Unit: 0.5dB
OCT hwxdslDynamicProfDpboEscm	1.3.6.1.2.1.10.94.1.1.65550.1.26	OCTET STRING	read-create	This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid. Octets 0+1 DPBOESCMA Octets 2+3 DPBOESCMB Octets 4+5 DPBOESCMC
U32 hwxdslDynamicProfDpboMus	1.3.6.1.2.1.10.94.1.1.65550.1.27	Unsigned32	read-create	DPBOMUS defines the assumed Minimum Usable receive Signal PSD (in dBm/Hz) for exchange based services, used to modify parameter DPBOFMAX defined below. It shall be coded as an unsigned integer representing a PSD level from 0 dBm/Hz (coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz. All values in the range are valid. Range: 0-255 Unit: 0.5dBm/Hz
U32 hwxdslDynamicProfDpboFMin	1.3.6.1.2.1.10.94.1.1.65550.1.28	Unsigned32	read-create	DPBOFMIN defines the minimum frequency from which the DPBO shall be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 0 kHz (coded as 0) to 8832 kHz (coded as 2048). Range: 0-2048 Unit: 4.3125 KHz
U32 hwxdslDynamicProfDpboFMax	1.3.6.1.2.1.10.94.1.1.65550.1.29	Unsigned32	read-create	DPBOFMAX defines the maximum frequency at which DPBO may be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956). Range: 32-6956 Unit: 4.3125 KHz
OCT hwxdslDynamicProfUpboPsdBand	1.3.6.1.2.1.10.94.1.1.65550.1.30	OCTET STRING	read-create	This parameter defines the UPBO reference PSD used to compute the upstream power back-off for each upstream band except US0. A UPBOPSD defined for each band ahsll consist of two parameters [a, b]. Parameter a shall be coded as an unsigned 12-bit number from 40 dBm/Hz (coded as 0) to 80.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz; and b shall be coded as an unsigned 12 bit number from 0 (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency f expressed in MHz shall be equal to '-a-b(SQRT(f))'. The set of parameter values a = 40 dBm/Hz, b = 0 dBm/Hz is a special configuration to disable UPBO in the respective upstream band. Octets 0+1 - a[0] Octets 2+3 - b[0] Octets 4+5 - a[1] Octets 6+7 - b[1] Octets 8+9 - a[2] Octets 10+11 - b[2] Octets 12+13 - a[3] Octets 14+15 - b[3]
INT hwxdslDynamicProfUpboKLF	1.3.6.1.2.1.10.94.1.1.65550.1.31	INTEGER	read-create	This parameter is a flag that forces the VTU-R to use the electrical loop length of the CO-MIB (UPBOKL) to compute the UPBO. The value shall be forced if the flag is set to 1. Otherwise, the electrical loop length shall be autonomously selected by the VTU-O. Options: 1. forced(1) - Force the CPE to use the electrical length of the CO(UPBOKL) to compute the UPBO 2. auto(2) - Electrical length shall be autonomously selected by the CO 3. invalidValue(-1) - Invalid value
U32 hwxdslDynamicProfUpboKL	1.3.6.1.2.1.10.94.1.1.65550.1.32	Unsigned32	read-create	This parameter defines the electrical loop length expressed in dB at 1MHz, kl0, configured by the CO-MIB. The value shall be coded as an unsigned 16 bit number in the range 0 (coded as 0) to 128 dB (coded as 1280) in steps of 0.1 dB. Range: 0-1280 Unit: 0.1 dB
OCT hwxdslDynamicProfRfiBands	1.3.6.1.2.1.10.94.1.1.65550.1.33	OCTET STRING	read-create	The subset of PSD mask breakpoints that shall be used to notch an RFI band. It is a string of bands consist of begin tone index and end tone index. for example :0-10,20-50,100-4095 It can contain as most as 16 bands.
OCT hwxdslDynamicProfToneBlackOut	1.3.6.1.2.1.10.94.1.1.65550.1.34	OCTET STRING	read-create	The subset of subcarriermask that shall be used to mask the subcarriers. It is a string of bands consist of begin tone index and end tone index. for example :0-10,20-50,100-4095 It can contain as most as 8 bands.
OCT hwxdslDynamicProfCarMaskDS	1.3.6.1.2.1.10.94.1.1.65550.1.35	OCTET STRING	read-create	Sub-carriers mask. A bitmap of 512 bits that allows masking up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the respective downstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCds < 512, all bits i (NSCds i <= 512) should be set to '1'.
OCT hwxdslDynamicProfCarMaskUS	1.3.6.1.2.1.10.94.1.1.65550.1.36	OCTET STRING	read-create	Sub-carriers mask. A bitmap of 64 bits that allows masking up to 64 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCus) is set to '1', the respective upstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCus < 64, all bits i (NSCus < i <= 64) should be set to '1'.
INT hwxdslDynamicProfXdslMode	1.3.6.1.2.1.10.94.1.1.65550.1.37	INTEGER	read-create	The XDSL Mode is a way of categorizing the various XDSL transmission modes into groups, each group (XDSL Mode) shares the same PSD configuration. Options: 1. defMode (1) - XDSL transmit mode is defMode 2. adsl (2) - XDSL transmit mode is adsl 3. adsl2Pots (3) - XDSL transmit mode is adsl2Pots 4. adsl2Isdn (4) - XDSL transmit mode is adsl2Isdn 5. adsl2PlusPots (5) - XDSL transmit mode is adsl2PlusPots 6. adsl2PlusIsdn (6) - XDSL transmit mode is adsl2PlusIsdn 7. adsl2ReachExtended (7) - XDSL transmit mode is adsl2ReachExtended 8. g9923PotsNonOverlapped(8) - XDSL transmit mode is g9923PotsNonOverlapped 9. g9923PotsOverlapped(9) - XDSL transmit mode is g9923PotsOverlapped 10. g9923IsdnNonOverlapped(10) - XDSL transmit mode is g9923IsdnNonOverlapped 11. g9923isdnOverlapped(11) - XDSL transmit mode is g9923isdnOverlapped 12. g9924potsNonOverlapped(14) - XDSL transmit mode is g9924potsNonOverlapped 13. g9924potsOverlapped(15) - XDSL transmit mode is g9924potsOverlapped 14. g9923AnnexIAllDigNonOverlapped(18) - XDSL transmit mode is g9923AnnexIAllDigNonOverlapped 15. g9923AnnexIAllDigOverlapped(19) - XDSL transmit mode is g9923AnnexIAllDigOverlapped 16. g9923AnnexJAllDigNonOverlapped(20) - XDSL transmit mode is g9923AnnexJAllDigNonOverlapped 17. g9923AnnexJAllDigOverlapped(21) - XDSL transmit mode is g9923AnnexJAllDigOverlapped 18. g9924AnnexIAllDigNonOverlapped(22) - XDSL transmit mode is g9924AnnexIAllDigNonOverlapped 19. g9924AnnexIAllDigOverlapped(23) - XDSL transmit mode is g9924AnnexIAllDigOverlapped 20. g9923AnnexLMode1NonOverlapped(24) - XDSL transmit mode is g9923AnnexLMode1NonOverlapped 21. g9923AnnexLMode2NonOverlapped(25) - XDSL transmit mode is g9923AnnexLMode2NonOverlapped 22. g9923AnnexLMode3Overlapped(26) - XDSL transmit mode is g9923AnnexLMode3Overlapped 23. g9923AnnexLMode4Overlapped(27) - XDSL transmit mode is g9923AnnexLMode4Overlapped 24. g9923AnnexMPotsNonOverlapped(28) - XDSL transmit mode is g9923AnnexMPotsNonOverlapped 25. g9923AnnexMPotsOverlapped(29) - XDSL transmit mode is g9923AnnexMPotsOverlapped 26. g9925PotsNonOverlapped(30) - XDSL transmit mode is g9925PotsNonOverlapped 27. g9925PotsOverlapped(31) - XDSL transmit mode is g9925PotsOverlapped 28. g9925IsdnNonOverlapped(32) - XDSL transmit mode is g9925IsdnNonOverlapped 29. g9925isdnOverlapped(33) - XDSL transmit mode is g9925isdnOverlapped 30. g9925AnnexIAllDigNonOverlapped(36) - XDSL transmit mode is g9925AnnexIAllDigNonOverlapped 31. g9925AnnexIAllDigOverlapped(37) - XDSL transmit mode is g9925AnnexIAllDigOverlapped 32. g9925AnnexJAllDigNonOverlapped(38) - XDSL transmit mode is g9925AnnexJAllDigNonOverlapped 33. g9925AnnexJAllDigOverlapped(39) - XDSL transmit mode is g9925AnnexJAllDigOverlapped 34. g9925AnnexMPotsNonOverlapped(40) - XDSL transmit mode is g9925AnnexMPotsNonOverlapped 35. g9925AnnexMPotsOverlapped(41) - XDSL transmit mode is g9925AnnexMPotsOverlapped 36. vdsl2Pots (42) - XDSL transmit mode is vdsl2Pots 37. vdsl2Isdn (43) - XDSL transmit mode is vdsl2Isdn 38. invalidValue(-1) - Invalid value
I32 hwxdslDynamicProfMaxNomPsdDs	1.3.6.1.2.1.10.94.1.1.65550.1.38	Integer32	read-create	The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz(physical values are -60 to -30 dBm/Hz). The invalid value is -1. If data is invalid, the invalid value will be returned. Unit: 0.1 dB
I32 hwxdslDynamicProfMaxNomPsdUs	1.3.6.1.2.1.10.94.1.1.65550.1.39	Integer32	read-create	The maximum nominal transmit PSD in the upstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz(physical values are -60 to -30 dBm/Hz). The invalid value is -1. If data is invalid, the invalid value will be returned. Unit: 0.1 dB
U32 hwxdslDynamicProfMaxNomAtpDs	1.3.6.1.2.1.10.94.1.1.65550.1.40	Unsigned32	read-create	The maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm). Range: 0-255 Unit: 0.1 dBm
U32 hwxdslDynamicProfMaxNomAtpUs	1.3.6.1.2.1.10.94.1.1.65550.1.41	Unsigned32	read-create	The maximum nominal aggregate transmit power in the upstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm). Range: 0-255 Unit: 0.1 dBm
OCT hwxdslDynamicProfPsdMaskDs	1.3.6.1.2.1.10.94.1.1.65550.1.42	OCTET STRING	read-create	This configuration parameter defines the downstream PSD mask applicable at the U C2 reference point. This MIB PSD mask may impose PSD restrictions in addition to the Limit PSD mask defined in the relevant Recommendation (e.g., G.992.5, G.993.2). This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCds - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 32, all remaining octets are set to the value 0xff. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
OCT hwxdslDynamicProfPsdMaskUs	1.3.6.1.2.1.10.94.1.1.65550.1.43	OCTET STRING	read-create	This configuration parameter defines the upstream PSD mask applicable at the U R2 reference point. This MIB PSD mask may impose PSD restrictions in addition to the Limit PSD mask defined in the relevant Recommendations (e.g., ITU-T Recommendations G.992.3, G.993.2). This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 45-47 - Same, for a 3rd breakpoint. This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCus - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value 0xff. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
INT hwxdslDynamicProfLimitMask	1.3.6.1.2.1.10.94.1.1.65550.1.44	INTEGER	read-create	This configuration parameter contains the G.993.2 profiles to be allowed by the near-end xTU on this line. Options: 1. profile8a (1) - The G.993.2 profile is profile8a 2. profile8b (2) - The G.993.2 profile is profile8b 3. profile8c (3) - The G.993.2 profile is profile8c 4. profile8d (4) - The G.993.2 profile is profile8d 5. profile12a (5) - The G.993.2 profile is profile12a 6. profile12b (6) - The G.993.2 profile is profile12b 7. profile17a (7) - The G.993.2 profile is profile17a 8. profile30a (8) - The G.993.2 profile is profile30a 9. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfClassMask	1.3.6.1.2.1.10.94.1.1.65550.1.45	INTEGER	read-create	In order to reduce the number of configuration possibilities, the limit PSD masks are grouped in the following PSD mask classes: Options: 1. annexA998-D-32(1) - Class 998 Annex A: D-32, D-64, D-48, D-128 2. annexA998-D-64(2) - Class 998 Annex A: D-32, D-64, D-48, D-128 3. annexB997-M1c-A-7(3) - Class 997-M1c Annex B: 997-M1c-A-7 4. annexB997-M1x-M-8(4) - Class 997-M1x Annex B: 997-M1x-M-8, 997-M1x-M 5. annexB997-M1x-M(5) - Class 997-M1x Annex B: 997-M1x-M-8, 997-M1x-M 6. annexB997-M2x-M-8(6) - Class 997-M2x Annex B: 997-M2x-M-8, 997-M2x-A, 997-M2x-M 7. annexB997-M2x-A(7) - Class 997-M2x Annex B: 997-M2x-M-8, 997-M2x-A, 997-M2x-M 8. annexB997-M2x-M(8) - Class 997-M2x Annex B: 997-M2x-M-8, 997-M2x-A, 997-M2x-M 9. annexB998-M1x-A(9) - Class 998-M1x Annex B: 998-M1x-A, 998-M1x-B, 998-M1x-NUS0 10. annexB998-M1x-B(10) - Class 998-M1x Annex B: 998-M1x-A, 998-M1x-B, 998-M1x-NUS0 11. annexB998-M1x-NUS0(11) - Class 998-M1x Annex B: 998-M1x-A, 998-M1x-B, 998-M1x-NUS0 12. annexB998-M2x-A(12) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0 13. annexB998-M2x-M(13) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0 14. annexB998-M2x-B(14) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0 15. annexB998-M2x-NUS0(15) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0 16. annexBHPE17-M1(16) - Class HPE17 Annex B: HPE17-M1 17. annexBHPE30-M1(17) - Class HPE30 Annex B: HPE30-M1 18. annexB997E17-M2x-A(18) - Class 997E17-M2x Annex B: 997E17-M2x-A 19. annexB997E30-M2x-NUS0(19) - Class 997E30-M2x Annex B: 997E30-M2x-NUS0 20. annexB998E17-M2x-NUS0(20) - Class 998E17-M2x Annex B: 998E17-M2x-NUS0, 998E17-M2x-NUS0-M 21. annexB998E17-M2x-NUS0-M(21) - Class 998E17-M2x Annex B: 998E17-M2x-NUS0, 998E17-M2x-NUS0-M 22. annexB998ADE17-M2x-NUS0-M(22) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M. 23. annexB998ADE17-M2x-B(23) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M. 24. annexB998E30-M2x-NUS0(24) - Class 998E30-M2x Annex B: 998E30-M2x-NUS0, 998E30-M2x-NUS0-M 25. annexB998E30-M2x-NUS0-M(25) - Class 998E30-M2x Annex B: 998E30-M2x-NUS0, 998E30-M2x-NUS0-M 26. annexB998ADE30-M2x-NUS0-M(26) - Class 998ADE30-M2x Annex B: 998ADE30-M2x-NUS0-M, 998ADE30-M2x-NUS0-A 27. annexB998ADE17-M2x-A(27) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M. 28. annexB998ADE30-M2x-NUS0-A(28) - Class 998ADE30-M2x Annex B: 998ADE30-M2x-NUS0-M, 998ADE30-M2x-NUS0-A 29. annexA998-D-48(29) - Class 998 Annex A: D-32, D-64, D-48, D-128 30. annexA998-D-128(30) - Class 998 Annex A: D-32, D-64, D-48, D-128 31. annexB998ADE17-M2x-M(31) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M. 32. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfBandOptUsage	1.3.6.1.2.1.10.94.1.1.65550.1.46	INTEGER	read-create	Defines the VDSL link use of the optional frequency range [25kHz - 138kHz] (Opt). Options: 1. disable(1) - Indicates Opt is unused 2. enable(2) - Indicates Opt usage is for upstream 3. invalidValue(-1) - Invalid value Huawei defined.
INT hwxdslDynamicProfVirtualNoiseModeDs	1.3.6.1.2.1.10.94.1.1.65550.1.47	INTEGER	read-create	Defines the Virtual Noise of downsteam. Options: 1. disable(1) - Unused 2. enable(2) - Used 3. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfVirtualNoiseModeUs	1.3.6.1.2.1.10.94.1.1.65550.1.48	INTEGER	read-create	Defines the Virtual Noise of upstream. Options: 1. disable(1) - Unused 2. enable(2) - Used 3. invalidValue(-1) - Invalid value
OCT hwxdslDynamicProfVirtualNoiseDs	1.3.6.1.2.1.10.94.1.1.65550.1.49	OCTET STRING	read-create	The Virtual Noise of downsteam. This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCds - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (127.5dBm/Hz) with steps of 0.5dBm/Hz.
OCT hwxdslDynamicProfVirtualNoiseUs	1.3.6.1.2.1.10.94.1.1.65550.1.50	OCTET STRING	read-create	The Virtual Noise of upsteam. This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCds - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (127.5dBm/Hz) with steps of 0.5dBm/Hz.
ROW hwxdslDynamicProfRowStatus	1.3.6.1.2.1.10.94.1.1.65550.1.51	RowStatus	read-create	This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be first unreferenced from all associated templates.
hwXdslPortIopCaptureTable	1.3.6.1.2.1.10.94.1.1.65551		not-accessible	The table hwXdslPortIopCaptureTable implement xDSL port IOP information capture. The index of this table is ifIndex.
hwXdslPortIopCaptureEntry	1.3.6.1.2.1.10.94.1.1.65551.1		not-accessible	The table hwXdslPortIopCaptureTable implement xDSL port IOP information capture. The index of this entry is ifIndex.
INT hwXdslPortIopCaptureOperType	1.3.6.1.2.1.10.94.1.1.65551.1.1	INTEGER	read-write	Start or stop IOP information capture of xDSL port. Options: 1. start(1) - Start IOP information capture of xDSL port 2. stop(2) - Stop IOP information capture of xDSL port 3. invalid(-1) - Invalid value
INT hwXdslPortIopCaptureOperStatus	1.3.6.1.2.1.10.94.1.1.65551.1.2	INTEGER	read-only	Port IOP capture status. Options: 1. noCapture(1) - Indicates that the capture is not performed 2. capturing(2) - Indicates that the capture is being performed 3. iopGenerate(3) - Indicates that the IOP file is generated 4. captured(4) - Indicates that the capture is complete 5. invalid(-1) - Invalid value
hwXdslDynamicInfoCollectTable	1.3.6.1.2.1.10.94.1.1.65552		not-accessible	The table hwXdslDynamicInfoCollectTable implement xDSL port Dynamic information collect. The index of this table is hwFrameIndex and hwSlotIndex.
hwXdslDynamicInfoCollectEntry	1.3.6.1.2.1.10.94.1.1.65552.1		not-accessible	The table hwXdslDynamicInfoCollectTable implement xDSL port Dynamic information collect. The index of this entry is hwFrameIndex and hwSlotIndex.
INT hwXdslDynamicInfoCollect	1.3.6.1.2.1.10.94.1.1.65552.1.1	INTEGER	read-write	Start Dynamic information collecting of Xdsl port. Options: 1. start(1) - Indicates that collecting data starts 2. invalid(-1) - Invalid value
INT hwXdslDynamicInfoCollectStatus	1.3.6.1.2.1.10.94.1.1.65552.1.2	INTEGER	read-only	Board Dynamic information collecting status. Options: 1. noCollect(1) - Indicates that collecting data is not performed 2. collecting(2) - Indicates that collecting data is being performed 3. collected(3) - Indicates that collecting data is complete
DAT hwXdslDynamicInfoCollectTime	1.3.6.1.2.1.10.94.1.1.65552.1.3	DateAndTime	read-only	Time when collecting the optimization information is complete.
hwAdslTraps	1.3.6.1.2.1.10.94.1.2.65536
hwAdslGeneralTraps	1.3.6.1.2.1.10.94.1.2.65536.1
hwAdslGeneralTrapsOIDs	1.3.6.1.2.1.10.94.1.2.65536.1.0
NTF hwAdslPortActRateMonitorTrap	1.3.6.1.2.1.10.94.1.2.65536.1.0.1			Definition of the trap reported when the ADSL port rate fails to meet the requirement. If ADSL act rate is lower than threshold, hwTrapType is 1. Otherwise, hwTrapType is 2.
NTF hwAdslPortRateChangeTrap	1.3.6.1.2.1.10.94.1.2.65536.1.0.2			ADSL act rate is change trap. This trap message is generated when the ADSL port rate change.
ADS hwadsl2LineTransAtucActual	1.3.6.1.2.1.10.94.3.1.17.1.65555	Adsl2TransmissionModeType	read-only	The actual transmission mode of the ATU-C. During ADSL line initialization, the ADSL Transceiver Unit - Remote terminal end (ATU-R) will determine the mode used for the link. This value will be limited a single transmission mode that is a subset of those modes enabled by the ATU-C and denoted by adslLineTransAtucConfig. After an initialization has occurred, its mode is saved as the 'Current' mode and is persistence should the link go down. This object returns 0 (i.e. BITS with no mode bit set) if the mode is not known.
hwAdsl	1.3.6.1.4.1.2011.6.31			This MIB is used for defining Huawei's ADSL management MIB objects.

Adsl2PsdMaskDs (1)
ADS hwadsl2TSSiPsdMaskDs	1.3.6.1.2.1.10.94.1.1.65543.1.19	Adsl2PsdMaskDs	read-write	The downstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G992.3 or G992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G992.5. This is a string of 32 pairs of values in the following structure: Octets 0-1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 32, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
Adsl2PsdMaskUs (1)
ADS hwadsl2TSSiPsdMaskUs	1.3.6.1.2.1.10.94.1.1.65543.1.39	Adsl2PsdMaskUs	read-write	The upstream PSD mask applicable at the U-C2 reference point. This parameter is used only for G992.3 or G992.5 and it may impose PSD restrictions (breakpoints) in addition to the Limit PSD mask defined in G992.5. This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 9-11, which are associated with a fourth breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCus. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 4, all remaining octets are set to the value 0. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
Adsl2SymbolProtection (2)
ADS hwadslExtDsINPmax	1.3.6.1.2.1.10.94.1.1.65543.1.36	Adsl2SymbolProtection	read-write	Maximum Impulse Noise Protection on downstream direction. The parameter can take the following values: noProtection(1), halfSymbol(2), singleSymbol(3), twoSymbols(4), threeSymbols(5), fourSymbols(6), fiveSymbols(7), sixSymbols(8), sevenSymbols(9), eightSymbols(10), nineSymbols(11), tenSymbols(12), elevenSymbols(13), twelveSymbols(14), thirteeSymbols(15), fourteenSymbols(16), fifteenSymbols(17), sixteenSymbols(18) The value multiply 1/2 is the real value of Noise Protection values. Unit: DMT Symbol
ADS hwadslExtUsINPmax	1.3.6.1.2.1.10.94.1.1.65543.1.32	Adsl2SymbolProtection	read-write	Maximum Impulse Noise Protection on upstream direction. The parameter can take the following values: noProtection(1), halfSymbol(2), singleSymbol(3), twoSymbols(4), threeSymbols(5), fourSymbols(6), fiveSymbols(7), sixSymbols(8), sevenSymbols(9), eightSymbols(10), nineSymbols(11), tenSymbols(12), elevenSymbols(13), twelveSymbols(14), thirteeSymbols(15), fourteenSymbols(16), fifteenSymbols(17), sixteenSymbols(18) The value multiply 1/2 is the real value of Noise Protection values. Unit: DMT Symbol Default: 1
Adsl2TransmissionModeType (2)
ADS hwadsl2LineTransAtucActual	1.3.6.1.2.1.10.94.3.1.17.1.65555	Adsl2TransmissionModeType	read-only	The actual transmission mode of the ATU-C. During ADSL line initialization, the ADSL Transceiver Unit - Remote terminal end (ATU-R) will determine the mode used for the link. This value will be limited a single transmission mode that is a subset of those modes enabled by the ATU-C and denoted by adslLineTransAtucConfig. After an initialization has occurred, its mode is saved as the 'Current' mode and is persistence should the link go down. This object returns 0 (i.e. BITS with no mode bit set) if the mode is not known.
ADS hwadslAturTransmissionCapabilities	1.3.6.1.2.1.10.94.1.1.3.1.65535	Adsl2TransmissionModeType	read-only	The ATU transmission system capability list of the different coding types. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the ATU supports the respective coding. The value may be derived from the handshaking procedures defined in G.994.1.
Bits (2)
BIT hwxdslDynamicProfPmMode	1.3.6.1.2.1.10.94.1.1.65550.1.19	Bits	read-create	Power management state Enabling. Defines the power states the xTU-C or xTU-R may autonomously transition to on this line. The various bit positions are: allowTransitionsToIdle (0) and allowTransitionsToLowPower (1). A bit with a '1' value means that the xTU is allowed to transit into the respective state and a '0' value means that the xTU is not allowed to transit into the respective state.
BIT hwxdslDynamicProfXtuTransSysEna	1.3.6.1.2.1.10.94.1.1.65550.1.2	Bits	read-create	Xtu Transmission System Enabling (ATSE). A list of the different coding types enabled in this profile. It is coded in a bit-map representation with 1 or more bits set. A bit set to '1' means that the XTUs may apply the respective coding for the XDSL line. A bit set to '0' means that the XTUs cannot apply the respective coding for the XDSL line. All 'reserved' bits should be set to '0'.
Counter32 (52)
C32 hwadslAtucChanCrcBlks	1.3.6.1.2.1.10.94.1.1.10.1.65538	Counter32	read-only	Count of all blocks received with CRC anomalies since agent reset.
C32 hwadslAtucChanFecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65536	Counter32	read-only	Count of all blocks received with FEC anomalies since agent reset.
C32 hwadslAtucChanHecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65537	Counter32	read-only	Count of all blocks received with HEC anomalies since agent reset.
C32 hwadslAtucChanPerfCurr15MinCrcBlks	1.3.6.1.2.1.10.94.1.1.10.1.65541	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel within the current 15 minute interval.
C32 hwadslAtucChanPerfCurr15MinFecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65539	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel within the current 15 minute interval.
C32 hwadslAtucChanPerfCurr15MinHecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65540	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel within the current 15 minute interval.
C32 hwadslAtucChanPerfCurr1DayCrcBlks	1.3.6.1.2.1.10.94.1.1.10.1.65544	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
C32 hwadslAtucChanPerfCurr1DayFecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65542	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
C32 hwadslAtucChanPerfCurr1DayHecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65543	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel during the current day as measured by adslAtucChanPerfCurr1DayTimeElapsed.
C32 hwadslAtucChanPerfPrev1DayCrcBlks	1.3.6.1.2.1.10.94.1.1.10.1.65547	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel within the most recent previous 1-day period.
C32 hwadslAtucChanPerfPrev1DayFecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65545	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel within the most recent previous 1-day period.
C32 hwadslAtucChanPerfPrev1DayHecBlks	1.3.6.1.2.1.10.94.1.1.10.1.65546	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel within the most recent previous 1-day period.
C32 hwAdslAtucIntervalFailFullInits	1.3.6.1.2.1.10.94.1.1.8.1.65535	Counter32	read-only	Count of the line initialization failed attempts during the interval.
C32 hwAdslAtucPerfCurr15MinFailFullInits	1.3.6.1.2.1.10.94.1.1.6.1.65536	Counter32	read-only	Count of the line initialization failed attempts in the current 15 minute interval.
C32 hwAdslAtucPerfCurr1DayFailFullInits	1.3.6.1.2.1.10.94.1.1.6.1.65537	Counter32	read-only	Count of the line initialization failed attempts in the day as measured by adslAtucPerfCurr1DayTimeElapsed.
C32 hwAdslAtucPerfFailFullInits	1.3.6.1.2.1.10.94.1.1.6.1.65535	Counter32	read-only	Count of the line initialization failed attempts since agent reset.
C32 hwAdslAtucPerfPrev1DayFailFullInits	1.3.6.1.2.1.10.94.1.1.6.1.65538	Counter32	read-only	Count of the line initialization failed attempts in the most recent previous 1-day period.
C32 hwadslAturChanCrcBlks	1.3.6.1.2.1.10.94.1.1.11.1.65538	Counter32	read-only	Count of all blocks received with CRC anomalies since agent reset.
C32 hwadslAturChanFecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65536	Counter32	read-only	Count of all blocks received with FEC anomalies since agent reset.
C32 hwadslAturChanHecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65537	Counter32	read-only	Count of all blocks received with HEC anomalies since agent reset.
C32 hwadslAturChanPerfCurr15MinCrcBlks	1.3.6.1.2.1.10.94.1.1.11.1.65541	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel within the current 15 minute interval.
C32 hwadslAturChanPerfCurr15MinFecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65539	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel within the current 15 minute interval.
C32 hwadslAturChanPerfCurr15MinHecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65540	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel within the current 15 minute interval.
C32 hwadslAturChanPerfCurr1DayCrcBlks	1.3.6.1.2.1.10.94.1.1.11.1.65544	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
C32 hwadslAturChanPerfCurr1DayFecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65542	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
C32 hwadslAturChanPerfCurr1DayHecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65543	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel during the current day as measured by adslAturChanPerfCurr1DayTimeElapsed.
C32 hwadslAturChanPerfPrev1DayCrcBlks	1.3.6.1.2.1.10.94.1.1.11.1.65547	Counter32	read-only	Count of all blocks received with CRC anomalies on this channel within the most recent previous 1-day period.
C32 hwadslAturChanPerfPrev1DayFecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65545	Counter32	read-only	Count of all blocks received with FEC anomalies on this channel within the most recent previous 1-day period.
C32 hwadslAturChanPerfPrev1DayHecBlks	1.3.6.1.2.1.10.94.1.1.11.1.65546	Counter32	read-only	Count of all blocks received with HEC anomalies on this channel within the most recent previous 1-day period.
C32 hwAdslPort15minUpTime	1.3.6.1.2.1.10.94.1.1.65546.1.14	Counter32	read-only	Up time in the interval. Unit: seconds
C32 hwAdslPort15minutesPerformanceInBytes	1.3.6.1.2.1.10.94.1.1.65546.1.2	Counter32	read-only	Read the receive bytes of xDSL port during 15 minutes.
C32 hwAdslPort15minutesPerformanceOutBytes	1.3.6.1.2.1.10.94.1.1.65546.1.3	Counter32	read-only	Read the transmit bytes of xDSL port during 15 minutes.
C32 hwAdslPortAtucCodeViolation	1.3.6.1.2.1.10.94.1.1.65546.1.6	Counter32	read-only	Seconds of head errors of the ATUC cell within 15 minutes.
C32 hwAdslPortAtucFecSeconds	1.3.6.1.2.1.10.94.1.1.65546.1.8	Counter32	read-only	Seconds of the ATUC FEC errors within 15 minutes.
C32 hwAdslPortAtucHecDropCellsCnt	1.3.6.1.2.1.10.94.1.1.65546.1.11	Counter32	read-only	ATUC cells discarded with HEC Errors.
C32 hwAdslPortAturCodeViolation	1.3.6.1.2.1.10.94.1.1.65546.1.7	Counter32	read-only	Seconds of head errors of the ATUC cell within 15 minutes.
C32 hwAdslPortAturFecSeconds	1.3.6.1.2.1.10.94.1.1.65546.1.9	Counter32	read-only	Error seconds of the ATUR FEC within 15 minutes.
C32 hwAdslPortAturHecDropCellsCnt	1.3.6.1.2.1.10.94.1.1.65546.1.12	Counter32	read-only	ATUR cells discarded with HEC Errors.
C32 hwAdslPortCurrent15minutesTimeElapse	1.3.6.1.2.1.10.94.1.1.65546.1.10	Counter32	read-only	Seconds that is passed within the current 15 minutes.
C32 hwAdslPortRateChangeTrapTimeStamp	1.3.6.1.2.1.10.94.1.1.65547.1.3	Counter32	accessible-for-notify	The time stamp of Line rate change trap. Standard Unix format; as the number of seconds since 1/1/1970 (UNIT:Second).
C32 hwAdslPortSyncFailNumber	1.3.6.1.2.1.10.94.1.1.65546.1.5	Counter32	read-only	Number of failed activations within 15 minutes.
C32 hwAdslPortSyncSuccNumber	1.3.6.1.2.1.10.94.1.1.65546.1.4	Counter32	read-only	Number of successful activations within 15 minutes.
C32 hwXdslPort15minutesPerformanceInBytes	1.3.6.1.2.1.10.94.1.1.65545.1.2	Counter32	read-only	Read the receive bytes of xDSL port during 15 minutes.
C32 hwXdslPort15minutesPerformanceOutBytes	1.3.6.1.2.1.10.94.1.1.65545.1.3	Counter32	read-only	Read the transmit bytes of xDSL port during 15 minutes.
C32 hwXdslPortAtucCodeViolation	1.3.6.1.2.1.10.94.1.1.65545.1.6	Counter32	read-only	Number of head errors of the ATUC cell within 15 minutes.
C32 hwXdslPortAtucFecSeconds	1.3.6.1.2.1.10.94.1.1.65545.1.8	Counter32	read-only	Seconds of the ATUC FEC errors within 15 minutes.
C32 hwXdslPortAturCodeViolation	1.3.6.1.2.1.10.94.1.1.65545.1.7	Counter32	read-only	Number of head errors of the ATUR cell within 15 minutes.
C32 hwXdslPortAturFecSeconds	1.3.6.1.2.1.10.94.1.1.65545.1.9	Counter32	read-only	Seconds of the ATUR FEC errors within 15 minutes.
C32 hwXdslPortCurrent15minutesStatTime	1.3.6.1.2.1.10.94.1.1.65545.1.10	Counter32	read-only	Seconds passed within the current 15 minutes.
C32 hwXdslPortSyncFailNumber	1.3.6.1.2.1.10.94.1.1.65545.1.5	Counter32	read-only	Number of failed activations of the xDSL port within 15 minutes.
C32 hwXdslPortSyncSuccNumber	1.3.6.1.2.1.10.94.1.1.65545.1.4	Counter32	read-only	Number of successful activations of the xDSL port within 15 minutes.
C32 hwXdslPortUpTime	1.3.6.1.2.1.10.94.1.1.65538.1.7	Counter32	read-only	Duration of the xDSL port activation. Unit: seconds
DateAndTime (7)
DAT hwAdslLineLatestActiveTime	1.3.6.1.2.1.10.94.1.1.65544.1.1	DateAndTime	read-only	Actual time when latest actived.
DAT hwAdslLineLatestDeactiveTime	1.3.6.1.2.1.10.94.1.1.65544.1.2	DateAndTime	read-only	Actual time when latest deactived. If port is actived, the value is invalid.
DAT hwAdslPreActiveTime	1.3.6.1.2.1.10.94.1.1.65539.1.7	DateAndTime	read-only	The last time at that the port was activated.
DAT hwXdslDynamicInfoCollectTime	1.3.6.1.2.1.10.94.1.1.65552.1.3	DateAndTime	read-only	Time when collecting the optimization information is complete.
DAT hwXdslPortClearUpCntTime	1.3.6.1.2.1.10.94.1.1.65538.1.704	DateAndTime	read-only	The time when up counts of a Xdsl port is cleared.
DAT hwXdslPortLastDownTime	1.3.6.1.2.1.10.94.1.1.65538.1.703	DateAndTime	read-only	Last down time of a Xdsl port.
DAT hwXdslPortLastUpTime	1.3.6.1.2.1.10.94.1.1.65538.1.702	DateAndTime	read-only	Last up time of a Xdsl port.
Gauge32 (75)
G32 hwadslAtucChanCodeGain	1.3.6.1.2.1.10.94.1.1.4.1.65544	Gauge32	read-only	Indicates Code Gain on downstream direction. It ranges from 0 to 16 units of 0.5 dB (physical values are 0 to 8 dB).
G32 hwadslAtucChanCurrINP	1.3.6.1.2.1.10.94.1.1.4.1.65536	Gauge32	read-only	Indicates Impulse Noise Protection on downstream direction. The value multiply 1/10000 is the real value. Unit: DMT Symbol
G32 hwAdslAtucChanCurrTxRate	1.3.6.1.2.1.10.94.1.1.65546.1.18	Gauge32	read-only	Actual transmit rate on this channel. Unit: bps
G32 hwadslAtucChanIntervalRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.12.1.65540	Gauge32	read-only	Count of units corrected by retransmission on this channel during this interval.
G32 hwadslAtucChanIntervalRtxCW	1.3.6.1.2.1.10.94.1.1.12.1.65539	Gauge32	read-only	Count of units request retransmission on this channel during this interval.
G32 hwadslAtucChanIntervalRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.12.1.65541	Gauge32	read-only	Count of units uncorrected by retransmission on this channel during this interval.
G32 hwadslAtucChanPcb	1.3.6.1.2.1.10.94.1.1.4.1.65545	Gauge32	read-only	Indicates Power Cut-back on downstream direction. It ranges from 0 to 400 units of 0.1 dB(physical values are 0 to 40 dB). Unit: tenth dB
G32 hwadslAtucChanPerfCurr15MinRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65552	Gauge32	read-only	Count of units corrected by retransmission on this channel within the current 15 minute interval.
G32 hwadslAtucChanPerfCurr15MinRtxCW	1.3.6.1.2.1.10.94.1.1.10.1.65551	Gauge32	read-only	Count of units request retransmission on this channel within the current 15 minute interval.
G32 hwadslAtucChanPerfCurr15MinRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65553	Gauge32	read-only	Count of units uncorrected by retransmission on this channel within the current 15 minute interval.
G32 hwadslAtucChanPerfCurr1DayRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65555	Gauge32	read-only	Count of units corrected by retransmission on this channel during the current day.
G32 hwadslAtucChanPerfCurr1DayRtxCW	1.3.6.1.2.1.10.94.1.1.10.1.65554	Gauge32	read-only	Count of units request retransmission on this channel during the current day.
G32 hwadslAtucChanPerfCurr1DayRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65556	Gauge32	read-only	Count of units uncorrected by retransmission on this channel during the current day.
G32 hwadslAtucChanPerfPrev1DayRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65558	Gauge32	read-only	Count of units corrected by retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAtucChanPerfPrev1DayRtxCW	1.3.6.1.2.1.10.94.1.1.10.1.65557	Gauge32	read-only	Count of units request retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAtucChanPerfPrev1DayRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65559	Gauge32	read-only	Count of units uncorrected by retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAtucChanPhyRrrcBits	1.3.6.1.2.1.10.94.1.1.4.1.65541	Gauge32	read-only	The bits in the channel that used to retransmission on downstream direction.
G32 hwadslAtucChanPhyRtxQueue	1.3.6.1.2.1.10.94.1.1.4.1.65542	Gauge32	read-only	Queues in send buffer on downstream direction.
G32 hwadslAtucChanRsDepth	1.3.6.1.2.1.10.94.1.1.4.1.65539	Gauge32	read-only	Indicates Reed-Solomon depth on downstream direction. Unit: byte
G32 hwadslAtucChanRsRedundancy	1.3.6.1.2.1.10.94.1.1.4.1.65538	Gauge32	read-only	Indicates Reed-Solomon redundancy on downstream direction. Unit: byte
G32 hwadslAtucChanRsSize	1.3.6.1.2.1.10.94.1.1.4.1.65543	Gauge32	read-only	Indicates Reed-Solomon Codeword Size on downstream direction . Range: 0-255 Unit: byte
G32 hwadslAtucChanRsSymbols	1.3.6.1.2.1.10.94.1.1.4.1.65537	Gauge32	read-only	Indicates Reed-Solomon symbols on downstream direction. The value multiply 1/10000 is the real value. Unit: byte
G32 hwadslAtucChanRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65549	Gauge32	read-only	Count of units corrected by retransmission since agent reset.
G32 hwadslAtucChanRtxCW	1.3.6.1.2.1.10.94.1.1.10.1.65548	Gauge32	read-only	Count of units request retransmission since agent reset.
G32 hwadslAtucChanRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.10.1.65550	Gauge32	read-only	Count of units uncorrected by retransmission since agent reset.
G32 hwadslAtucChanSymbolLength	1.3.6.1.2.1.10.94.1.1.4.1.65540	Gauge32	read-only	Indicates the Bit Number of the DMT Symbol on downstream direction. Unit: bit
G32 hwAdslAtucCurrAtn	1.3.6.1.2.1.10.94.1.1.65546.1.15	Gauge32	read-only	Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU. Range: 0-630 Unit: tenth dB
G32 hwAdslAtucCurrAttainableRate	1.3.6.1.2.1.10.94.1.1.65546.1.17	Gauge32	read-only	Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate. Unit: bps
G32 hwAdslAtucCurrSignalAtn	1.3.6.1.2.1.10.94.1.1.2.1.65537	Gauge32	read-only	Current signal attenuation of the ATU-C, indicating the difference between the transmit signal of the ATU-R and the receive signal of the ATU-C. Range: 0-630 Unit: tenth dB
G32 hwAdslAtucLatestAtn	1.3.6.1.2.1.10.94.1.1.65544.1.7	Gauge32	read-only	Measured difference in the total power transmitted as seen by this ATU-C at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
G32 hwAdslAtucLatestAttainableRate	1.3.6.1.2.1.10.94.1.1.65544.1.9	Gauge32	read-only	Indicates the maximum attainable data rate by the ATU-C at the time of the last adslAtucRateChangeTrap event. Unit: bps
G32 hwAdslAtucLatestConfTxRate	1.3.6.1.2.1.10.94.1.1.65544.1.11	Gauge32	read-only	Configured transmit rate for ADSL port, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates. Unit: bps
G32 hwAdslAtucLatestInterleaveDelay	1.3.6.1.2.1.10.94.1.1.65544.1.13	Gauge32	read-only	Interleave Delay for this channel when latest actived. Unit: milliseconds
G32 hwAdslAtucLatestTxRate	1.3.6.1.2.1.10.94.1.1.65544.1.3	Gauge32	read-only	Actual transmit rate on this channel when latest actived. Unit: bps
G32 hwAdslAtucLatestTxRateThreshold	1.3.6.1.2.1.10.94.1.1.65544.1.17	Gauge32	read-only	Port down stream threshold. Unit: bps
G32 hwAdslAtucPreAtn	1.3.6.1.2.1.10.94.1.1.65539.1.5	Gauge32	read-only	Measured difference in the total power transmitted as seen by this ATU-C at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
G32 hwadslAturChanCodeGain	1.3.6.1.2.1.10.94.1.1.5.1.65544	Gauge32	read-only	Indicates Code Gain on upstream direction. It ranges from 0 to 16 units of 0.5 dB (physical values are 0 to 8 dB).
G32 hwadslAturChanCurrINP	1.3.6.1.2.1.10.94.1.1.5.1.65536	Gauge32	read-only	Indicates Impulse Noise Protection on upstream direction. The value multiply 1/10000 is the real value. Unit: DMT Symbol
G32 hwAdslAturChanCurrTxRate	1.3.6.1.2.1.10.94.1.1.65546.1.22	Gauge32	read-only	Actual transmit rate on this channel. Unit: bps
G32 hwadslAturChanIntervalRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.13.1.65540	Gauge32	read-only	Count of units corrected by retransmission on this channel during this interval.
G32 hwadslAturChanIntervalRtxCW	1.3.6.1.2.1.10.94.1.1.13.1.65539	Gauge32	read-only	Count of units request retransmission on this channel during this interval.
G32 hwadslAturChanIntervalRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.13.1.65541	Gauge32	read-only	Count of units uncorrected by retransmission on this channel during this interval.
G32 hwadslAturChanPerfCurr15MinRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65552	Gauge32	read-only	Count of units corrected by retransmission on this channel within the current 15 minute interval.
G32 hwadslAturChanPerfCurr15MinRtxCW	1.3.6.1.2.1.10.94.1.1.11.1.65551	Gauge32	read-only	Count of units request retransmission on this channel within the current 15 minute interval.
G32 hwadslAturChanPerfCurr15MinRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65553	Gauge32	read-only	Count of units uncorrected by retransmission on this channel within the current 15 minute interval.
G32 hwadslAturChanPerfCurr1DayRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65555	Gauge32	read-only	Count of units corrected by retransmission on this channel during the current day.
G32 hwadslAturChanPerfCurr1DayRtxCW	1.3.6.1.2.1.10.94.1.1.11.1.65554	Gauge32	read-only	Count of units request retransmission on this channel during the current day.
G32 hwadslAturChanPerfCurr1DayRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65556	Gauge32	read-only	Count of units uncorrected by retransmission on this channel during the current day.
G32 hwadslAturChanPerfPrev1DayRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65558	Gauge32	read-only	Count of units corrected by retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAturChanPerfPrev1DayRtxCW	1.3.6.1.2.1.10.94.1.1.11.1.65557	Gauge32	read-only	Count of units request retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAturChanPerfPrev1DayRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65559	Gauge32	read-only	Count of units uncorrected by retransmission on this channel within the most recent previous 1-day period.
G32 hwadslAturChanPhyRrrcBits	1.3.6.1.2.1.10.94.1.1.5.1.65541	Gauge32	read-only	The bits in the channel that used to retransmission on upstream direction.
G32 hwadslAturChanPhyRtxQueue	1.3.6.1.2.1.10.94.1.1.5.1.65542	Gauge32	read-only	Queues in send buffer on upstream direction.
G32 hwadslAturChanRsDepth	1.3.6.1.2.1.10.94.1.1.5.1.65539	Gauge32	read-only	Indicates Reed-Solomon depth on upstream direction. Unit: byte
G32 hwadslAturChanRsRedundancy	1.3.6.1.2.1.10.94.1.1.5.1.65538	Gauge32	read-only	Indicates Reed-Solomon redundancy on upstream direction. Unit: byte
G32 hwadslAturChanRsSize	1.3.6.1.2.1.10.94.1.1.5.1.65543	Gauge32	read-only	Indicates Reed-Solomon Codeword Size on upstream direction. Range: 0-255 Unit: byte
G32 hwadslAturChanRsSymbols	1.3.6.1.2.1.10.94.1.1.5.1.65537	Gauge32	read-only	Indicates Reed-Solomon symbols on upstream direction. The value multiply 1/10000 is the real value. Unit: byte
G32 hwadslAturChanRtxCorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65549	Gauge32	read-only	Count of units corrected by retransmission since agent reset.
G32 hwadslAturChanRtxCW	1.3.6.1.2.1.10.94.1.1.11.1.65548	Gauge32	read-only	Count of units request retransmission since agent reset.
G32 hwadslAturChanRtxUncorrectedCW	1.3.6.1.2.1.10.94.1.1.11.1.65550	Gauge32	read-only	Count of units uncorrected by retransmission since agent reset.
G32 hwadslAturChanSymbolLength	1.3.6.1.2.1.10.94.1.1.5.1.65540	Gauge32	read-only	Indicates the Bit Number of the DMT Symbol on upstream direction. Unit: bit
G32 hwAdslAturCurrAtn	1.3.6.1.2.1.10.94.1.1.65546.1.19	Gauge32	read-only	Measured difference in the total power transmitted by the peer ATU and the total power received by this ATU. Range: 0-630 Unit: tenth dB
G32 hwAdslAturCurrAttainableRate	1.3.6.1.2.1.10.94.1.1.65546.1.21	Gauge32	read-only	Indicates the maximum currently attainable data rate by the ATU. This value will be equal or greater than the current line rate. Unit: bps
G32 hwAdslAturCurrSignalAtn	1.3.6.1.2.1.10.94.1.1.3.1.65536	Gauge32	read-only	The signal attenuation value on ATUR: It indicates the difference between the transmit signal of the ATU-C and the receive signal of the ATU-R. Range: 0-630 Unit: tenth dB
G32 hwAdslAturLatestAtn	1.3.6.1.2.1.10.94.1.1.65544.1.8	Gauge32	read-only	Measured difference in the total power transmitted as seen by this ATU-R at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
G32 hwAdslAturLatestAttainableRate	1.3.6.1.2.1.10.94.1.1.65544.1.10	Gauge32	read-only	Indicates the maximum attainable data rate by the ATU-R at the time of the last adslAtucRateChangeTrap event. Unit: bps
G32 hwAdslAturLatestConfTxRate	1.3.6.1.2.1.10.94.1.1.65544.1.12	Gauge32	read-only	Configured receive rate for ADSL port, in bps. See adslAtucConfRateChanRatio for information regarding RADSL mode and ATUR transmit rate for ATUC receive rates. Unit: bps
G32 hwAdslAturLatestInterleaveDelay	1.3.6.1.2.1.10.94.1.1.65544.1.14	Gauge32	read-only	Interleave Delay for this channel when latest actived. Unit: milliseconds
G32 hwAdslAturLatestTxRate	1.3.6.1.2.1.10.94.1.1.65544.1.4	Gauge32	read-only	Actual transmit rate on this channel when latest actived. Unit: bps
G32 hwAdslAturLatestTxRateThreshold	1.3.6.1.2.1.10.94.1.1.65544.1.18	Gauge32	read-only	Port up stream threshold. Unit: bps
G32 hwAdslAturPreAtn	1.3.6.1.2.1.10.94.1.1.65539.1.6	Gauge32	read-only	Measured difference in the total power transmitted as seen by this ATU-R at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
G32 hwAdslPortRateChangeTrapDSLineRate	1.3.6.1.2.1.10.94.1.1.65547.1.4	Gauge32	accessible-for-notify	Down stream line rate after line rate change.
G32 hwAdslPortRateChangeTrapUSLineRate	1.3.6.1.2.1.10.94.1.1.65547.1.5	Gauge32	accessible-for-notify	Up stream line rate after line rate change.
G32 hwXdslPortDownThresholdTxRate	1.3.6.1.2.1.10.94.1.1.65538.1.5	Gauge32	read-write	Set Port monitoring downstream rate threshold value. Default: 0 Unit: bps
G32 hwXdslPortUpThresholdTxRate	1.3.6.1.2.1.10.94.1.1.65538.1.4	Gauge32	read-write	Set Port monitoring upstream rate threshold value. Default: 0 Unit: bps
HWADSL2ANNEXMSCOPE (1)
HWA hwadsl2TransMissionAnnexMScope	1.3.6.1.2.1.10.94.1.1.65543.1.22	HWADSL2ANNEXMSCOPE	read-create	Annex M expand scope: 1-Tone Index(7~32) 2-Tone Index(7~36) 3-Tone Index(7~40) 4-Tone Index(7~44) 5-Tone Index(7~48) 6-Tone Index(7~52) 7-Tone Index(7~56) 8-Tone Index(7~60) 9-Tone Index(7~64) -1-invalidValue
HWADSLSYMBOLPROTECTION (2)
HWA hwadsl2ChConfProfMinProtectionDs	1.3.6.1.2.1.10.94.1.1.65543.1.14	HWADSLSYMBOLPROTECTION	read-write	Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection(0), halfSymbol(1), singleSymbol(2), twoSymbols(4), threeSymbols(6), fourSymbols(8), fiveSymbols(10), sixSymbols(12), sevenSymbols(14), eightSymbols(16), nineSymbols(18), tenSymbols(20), elevenSymbols(22), twelveSymbols(24), thirteenSymbols(26), fourteenSymbols(28), fifteenSymbols(30), sixteenSymbols(32), null(65535) The value multiply 1/2 is the real value of Noise Protection values.
HWA hwadsl2ChConfProfMinProtectionUs	1.3.6.1.2.1.10.94.1.1.65543.1.15	HWADSLSYMBOLPROTECTION	read-write	Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection(0), halfSymbol(1), singleSymbol(2), twoSymbols(4), threeSymbols(6), fourSymbols(8), fiveSymbols(10), sixSymbols(12), sevenSymbols(14), eightSymbols(16), nineSymbols(18), tenSymbols(20), elevenSymbols(22), twelveSymbols(24), thirteenSymbols(26), fourteenSymbols(28), fifteenSymbols(30), sixteenSymbols(32), null(65535) The value multiply 1/2 is the real value of Noise Protection values.
HWADSLTRANSMISSIONMODETYPE (1)
HWA hwAdslAtucCurrTransMode	1.3.6.1.2.1.10.94.1.1.2.1.65536	HWADSLTRANSMISSIONMODETYPE	read-only	A set of ADSL line transmission modes.
INTEGER (44)
INT hwadsl2L2ModeState	1.3.6.1.2.1.10.94.1.1.65543.1.23	INTEGER	read-create	The state of L2 power management mode. Options: 1. disabled(1) - L2 power management mode is disabled 2. enabled(2) - L2 power management mode is enabled 3. forced(3) - L2 power management mode is forced Default: disabled(1)
INT hwAdsl2SCStatusDirection	1.3.6.1.2.1.10.94.1.1.65549.1.1	INTEGER	not-accessible	The direction of the sub-carrier is either upstream or downstream. Options: 1. upstream(1) - Upstream sub-carrier 2. downstream(2) - Downstream sub-carrier
INT hwAdslAtucConfDownBitSwap	1.3.6.1.2.1.10.94.1.1.14.1.65536	INTEGER	read-create	Enables and disables the down bitswap of a template. Options: 1. enabled(1) - Indicates that the downstream bit swap is enabled 2. disabled(2) - Indicates that the downstream bit swap is disabled Default: enabled(1)
INT hwAdslAtucConfUpBitSwap	1.3.6.1.2.1.10.94.1.1.14.1.65537	INTEGER	read-create	Enables and disables the up bitswap of a template. Options: 1. enabled(1) - Indicates that the upstream bit swap is enabled 2. disabled(2) - Indicates that the upstream bit swap is disabled Default: enabled(1)
INT hwadslExtDsPhyRcontrol	1.3.6.1.2.1.10.94.1.1.65543.1.35	INTEGER	read-write	To enable or disable the PHY-R function on downstream direction. Options: 1. enable(1) - The PHY-R function on downstream direction is enabled 2. disable(2) - The PHY-R function on downstream direction is disabled Default: disable(2)
INT hwadslExtUsPhyRcontrol	1.3.6.1.2.1.10.94.1.1.65543.1.31	INTEGER	read-write	To enable or disable the PHY-R function on upstream direction. Options: 1. enable(1) - The PHY-R function on upstream direction is enabled 2. disable(2) - The PHY-R function on upstream direction is disabled Default: disable(2)
INT hwadslLConfProfAdslMode	1.3.6.1.2.1.10.94.1.1.65543.1.40	INTEGER	read-write	The ADSL2 management model specified includes an ADSL Mode attribute which identifies an instance of ADSL Mode-Specific PSD Configuration object in the ADSL Line Profile. The following classes of ADSL operating mode are defined. Options: 1. defMode(1) - ADSL transmit mode is defMode 2. adsl(2) - ADSL transmit mode is adsl 3. adsl2Pots(3) - ADSL transmit mode is adsl2Pots 4. adsl2Isdn(4) - ADSL transmit mode is adsl2Isdn 5. adsl2PlusPots(5) - ADSL transmit mode is adsl2PlusPots 6. adsl2PlusIsdn(6) - ADSL transmit mode is adsl2PlusIsdn 7. adsl2ReachExtended(7) - ADSL transmit mode is adsl2ReachExtended 8. invalidValue(-1) - Invalid value
INT hwadslLineAlarmConfProfileDyingGasp	1.3.6.1.2.1.10.94.1.1.15.1.65536	INTEGER	read-create	This object enables/disables the report of LOSS-OF-POWER alarm in an ADSL line, This object is defaulted enable(1). Options: 1. enable (1) - The LOSS-OF-POWER alarm in an ADSL line will be reported 2. disable (2) - The LOSS-OF-POWER alarm in an ADSL line will not be reported
INT hwadslLineDisableToneSection1Flag	1.3.6.1.2.1.10.94.1.1.65543.1.4	INTEGER	read-create	The enable flag of section1. Options: 1. enabled(1) - The first tone section is enabled 2. disabled(2) - The first tone section is disabled
INT hwadslLineDisableToneSection2Flag	1.3.6.1.2.1.10.94.1.1.65543.1.7	INTEGER	read-create	The enable flag of section2. Options: 1. enabled(1) - The second tone section is enabled 2. disabled(2) - The second tone section is disabled
INT hwadslLineDisableToneSection3Flag	1.3.6.1.2.1.10.94.1.1.65543.1.10	INTEGER	read-create	The enable flag of the third section. Options: 1. enabled(1) - The third tone section is enabled 2. disabled(2) - The third tone section is disabled
INT hwadslLineDisableToneSection4Flag	1.3.6.1.2.1.10.94.1.1.65543.1.13	INTEGER	read-create	The enable flag of the fourth section. Range: 0-511 Options: 1. enabled(1) - The fourth tone section is enabled 2. disabled(2) - The fourth tone section is disabled
INT hwAdslLinePvcConnectType	1.3.6.1.2.1.10.94.1.1.65536.1.10	INTEGER	read-only	The Connected type of the adsl line PVC. Options: 1. auto(0) - The Connected type of the adsl line PVC is auto 2. llc1483B(1) - The Connected type of the adsl line PVC is llc1483B 3. pppoaLLC(2) - The Connected type of the adsl line PVC is pppoaLLC 4. pppoaVcmux(3) - The Connected type of the adsl line PVC is pppoaVcmux 5. ipoaLLc(4) - The Connected type of the adsl line PVC is ipoaLLc 6. ipoaVcmux(5) - The Connected type of the adsl line PVC is ipoaVcmux
INT hwAdslLinePvcIGMPEnable	1.3.6.1.2.1.10.94.1.1.65536.1.8	INTEGER	read-write	This object allows the adsl line PVC to support IGMP. Options: 1. enable(1) - Indicates that the PVC of the ADSL port is enabled to support IGMP 2. disable(2) - Indicates that the PVC of the ADSL port is disabled to support IGMP Default: disable(2)
INT hwAdslLinePvcMCastEnable	1.3.6.1.2.1.10.94.1.1.65536.1.7	INTEGER	read-write	This object allows the adsl line PVC to support multicast. Options: 1. enable(1) - Indicates that the PVC of the ADSL port is enabled to support the multicast 2. disable(2) - Indicates that the PVC of the ADSL port is disabled to support the multicast Default: disable(2)
INT hwAdslPortCurrentActMode	1.3.6.1.2.1.10.94.1.1.65546.1.44	INTEGER	read-only	Instantaneous value of the technology type that line is currently trained up under. Options: 1. adsl(1) - Indicates that line is currently trained up under adsl type 2. adsl2(2) - Indicates that line is currently trained up under adsl2 type 3. adsl2plus(3) - Indicates that line is currently trained up under adsl2+ type
INT hwAdslPortRateChangeTrapConfig	1.3.6.1.2.1.10.94.1.1.65548.1	INTEGER	read-write	Enable or disable ADSL port line-rate change trap feature. Options: 1. enabled(1) - ADSL port line-rate change trap feature is enabled 2. disabled(2) - ADSL port line-rate change trap feature is disabled
INT hwAdslTransmissionMode	1.3.6.1.2.1.10.94.1.1.14.1.65539	INTEGER	read-create	Indicates the transmission mode of this channel. Options: 1. all(1) - All (G992.1, G992.2, T1.413)(Default) 2. fullRate(2) - Full rate(G992.1 or T1.413) 3. gliteOnly(3) - G992.2(g.lite) only 4. t1413Only(4) - T1.413 only 5. gdmtOnly(5) - G992.1,G992.3,G992.5,(g.dmt) only 6. ghs(6) - g.hs (G992.1,G992.2,G992.3,G992.4,G992.5,G992.5 is prior) 7. g992Dot1(7) - G992.1 8. g992Dot2(8) - G992.2 9. g992Dot3(9) - G992.3 10. g992Dot4(10) - G992.4 11. g992Dot5(11) - G992.5 12. adslAllOnly(12) - ADSL ALL ONLY 13. adslAndAdsl2(13) - G.992.1,G.992.3,T1.413(Not support) Default: all(1)
INT hwAdslTrellionsModeEnable	1.3.6.1.2.1.10.94.1.1.14.1.65538	INTEGER	read-create	Enables and disables the Trellions mode. Options: 1. enabled(1) - Indicates that the trellis coding is enabled 2. disabled(2) - Indicates that the trellis coding is disabled Default: enabled(1)
INT hwPortThreePriorityEnable	1.3.6.1.2.1.10.94.1.1.65540.1.1	INTEGER	read-write	Three Priority status of the interface. Options: 1. enable(1) - Adsl port three priority is enabled 2. disable(2) - Adsl port three priority is disabled
INT hwSlotMacMaxNoLimitEnable	1.3.6.1.2.1.10.94.1.1.65541.1.1	INTEGER	read-write	This object is used to set whether all the ports in the slot limits the maximum number of learning MAC addresses. Options: 1. enable(1) - Don't limit the max NO. of learning mac addresses in the slot 2. disable(2) - Limit the max NO. of learning mac addresses in the slot
INT hwXdslDynamicInfoCollect	1.3.6.1.2.1.10.94.1.1.65552.1.1	INTEGER	read-write	Start Dynamic information collecting of Xdsl port. Options: 1. start(1) - Indicates that collecting data starts 2. invalid(-1) - Invalid value
INT hwXdslDynamicInfoCollectStatus	1.3.6.1.2.1.10.94.1.1.65552.1.2	INTEGER	read-only	Board Dynamic information collecting status. Options: 1. noCollect(1) - Indicates that collecting data is not performed 2. collecting(2) - Indicates that collecting data is being performed 3. collected(3) - Indicates that collecting data is complete
INT hwxdslDynamicProfBandOptUsage	1.3.6.1.2.1.10.94.1.1.65550.1.46	INTEGER	read-create	Defines the VDSL link use of the optional frequency range [25kHz - 138kHz] (Opt). Options: 1. disable(1) - Indicates Opt is unused 2. enable(2) - Indicates Opt usage is for upstream 3. invalidValue(-1) - Invalid value Huawei defined.
INT hwxdslDynamicProfBitSwapDS	1.3.6.1.2.1.10.94.1.1.65550.1.3	INTEGER	read-create	Enables or disables the bit swap downstream of a line. Options: 1. disable(1) - The bit swap downstream of a line is disabled 2. enable(2) - The bit swap downstream of a line is enabled 3. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfBitSwapUS	1.3.6.1.2.1.10.94.1.1.65550.1.4	INTEGER	read-create	Enables or disables the bit swap upstream of a line. Options: 1. disable(1) - The bit swap upstream of a line is disabled 2. enable(2) - The bit swap upstream of a line is enabled 3. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfCh1MinProtectionDs	1.3.6.1.2.1.10.94.1.1.65550.1.11	INTEGER	read-create	Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Options: 1. noProtection (1) - Indicates that the INP value is 0 2. halfSymbol (2) - Indicates that the INP value is 0.5 3. singleSymbol (3) - Indicates that the INP value is 1 4. twoSymbols (4) - Indicates that the INP value is 2 5. threeSymbols (5) - Indicates that the INP value is 3 6. fourSymbols (6) - Indicates that the INP value is 4 7. fiveSymbols (7) - Indicates that the INP value is 5 8. sixSymbols (8) - Indicates that the INP value is 6 9. sevenSymbols (9) - Indicates that the INP value is 7 10. eightSymbols (10) - Indicates that the INP value is 8 11. nineSymbols (11) - Indicates that the INP value is 9 12. tenSymbols (12) - Indicates that the INP value is 10 13. elevenSymbols (13) - Indicates that the INP value is 11 14. twelveSymbols (14) - Indicates that the INP value is 12 15. thirteenSymbols (15) - Indicates that the INP value is 13 16. fourteenSymbols (16) - Indicates that the INP value is 14 17. fifteenSymbols (17) - Indicates that the INP value is 15 18. sixteenSymbols (18) - Indicates that the INP value is 16 19. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfCh1MinProtectionUs	1.3.6.1.2.1.10.94.1.1.65550.1.12	INTEGER	read-create	Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Options: 1. noProtection (1) - Indicates that the INP value is 0 2. halfSymbol (2) - Indicates that the INP value is 0.5 3. singleSymbol (3) - Indicates that the INP value is 1 4. twoSymbols (4) - Indicates that the INP value is 2 5. threeSymbols (5) - Indicates that the INP value is 3 6. fourSymbols (6) - Indicates that the INP value is 4 7. fiveSymbols (7) - Indicates that the INP value is 5 8. sixSymbols (8) - Indicates that the INP value is 6 9. sevenSymbols (9) - Indicates that the INP value is 7 10. eightSymbols (10) - Indicates that the INP value is 8 11. nineSymbols (11) - Indicates that the INP value is 9 12. tenSymbols (12) - Indicates that the INP value is 10 13. elevenSymbols (13) - Indicates that the INP value is 11 14. twelveSymbols (14) - Indicates that the INP value is 12 15. thirteenSymbols (15) - Indicates that the INP value is 13 16. fourteenSymbols (16) - Indicates that the INP value is 14 17. fifteenSymbols (17) - Indicates that the INP value is 15 18. sixteenSymbols (18) - Indicates that the INP value is 16 19. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfCh2MinProtectionDs	1.3.6.1.2.1.10.94.1.1.65550.1.15	INTEGER	read-create	Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Options: 1. noProtection (1) - Indicates that the INP value is 0 2. halfSymbol (2) - Indicates that the INP value is 0.5 3. singleSymbol (3) - Indicates that the INP value is 1 4. twoSymbols (4) - Indicates that the INP value is 2 5. threeSymbols (5) - Indicates that the INP value is 3 6. fourSymbols (6) - Indicates that the INP value is 4 7. fiveSymbols (7) - Indicates that the INP value is 5 8. sixSymbols (8) - Indicates that the INP value is 6 9. sevenSymbols (9) - Indicates that the INP value is 7 10. eightSymbols (10) - Indicates that the INP value is 8 11. nineSymbols (11) - Indicates that the INP value is 9 12. tenSymbols (12) - Indicates that the INP value is 10 13. elevenSymbols (13) - Indicates that the INP value is 11 14. twelveSymbols (14) - Indicates that the INP value is 12 15. thirteenSymbols (15) - Indicates that the INP value is 13 16. fourteenSymbols (16) - Indicates that the INP value is 14 17. fifteenSymbols (17) - Indicates that the INP value is 15 18. sixteenSymbols (18) - Indicates that the INP value is 16 19. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfCh2MinProtectionUs	1.3.6.1.2.1.10.94.1.1.65550.1.16	INTEGER	read-create	Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not required), halfSymbol (i.e., INP length is 1/2 symbol) and 1-16 symbols in steps of 1 symbol. Options: 1. noProtection (1) - Indicates that the INP value is 0 2. halfSymbol (2) - Indicates that the INP value is 0.5 3. singleSymbol (3) - Indicates that the INP value is 1 4. twoSymbols (4) - Indicates that the INP value is 2 5. threeSymbols (5) - Indicates that the INP value is 3 6. fourSymbols (6) - Indicates that the INP value is 4 7. fiveSymbols (7) - Indicates that the INP value is 5 8. sixSymbols (8) - Indicates that the INP value is 6 9. sevenSymbols (9) - Indicates that the INP value is 7 10. eightSymbols (10) - Indicates that the INP value is 8 11. nineSymbols (11) - Indicates that the INP value is 9 12. tenSymbols (12) - Indicates that the INP value is 10 13. elevenSymbols (13) - Indicates that the INP value is 11 14. twelveSymbols (14) - Indicates that the INP value is 12 15. thirteenSymbols (15) - Indicates that the INP value is 13 16. fourteenSymbols (16) - Indicates that the INP value is 14 17. fifteenSymbols (17) - Indicates that the INP value is 15 18. sixteenSymbols (18) - Indicates that the INP value is 16 19. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfClassMask	1.3.6.1.2.1.10.94.1.1.65550.1.45	INTEGER	read-create	In order to reduce the number of configuration possibilities, the limit PSD masks are grouped in the following PSD mask classes: Options: 1. annexA998-D-32(1) - Class 998 Annex A: D-32, D-64, D-48, D-128 2. annexA998-D-64(2) - Class 998 Annex A: D-32, D-64, D-48, D-128 3. annexB997-M1c-A-7(3) - Class 997-M1c Annex B: 997-M1c-A-7 4. annexB997-M1x-M-8(4) - Class 997-M1x Annex B: 997-M1x-M-8, 997-M1x-M 5. annexB997-M1x-M(5) - Class 997-M1x Annex B: 997-M1x-M-8, 997-M1x-M 6. annexB997-M2x-M-8(6) - Class 997-M2x Annex B: 997-M2x-M-8, 997-M2x-A, 997-M2x-M 7. annexB997-M2x-A(7) - Class 997-M2x Annex B: 997-M2x-M-8, 997-M2x-A, 997-M2x-M 8. annexB997-M2x-M(8) - Class 997-M2x Annex B: 997-M2x-M-8, 997-M2x-A, 997-M2x-M 9. annexB998-M1x-A(9) - Class 998-M1x Annex B: 998-M1x-A, 998-M1x-B, 998-M1x-NUS0 10. annexB998-M1x-B(10) - Class 998-M1x Annex B: 998-M1x-A, 998-M1x-B, 998-M1x-NUS0 11. annexB998-M1x-NUS0(11) - Class 998-M1x Annex B: 998-M1x-A, 998-M1x-B, 998-M1x-NUS0 12. annexB998-M2x-A(12) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0 13. annexB998-M2x-M(13) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0 14. annexB998-M2x-B(14) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0 15. annexB998-M2x-NUS0(15) - Class 998-M2x Annex B: 998-M2x-A, 998-M2x-M, 998-M2x-B, 998-M2x-NUS0 16. annexBHPE17-M1(16) - Class HPE17 Annex B: HPE17-M1 17. annexBHPE30-M1(17) - Class HPE30 Annex B: HPE30-M1 18. annexB997E17-M2x-A(18) - Class 997E17-M2x Annex B: 997E17-M2x-A 19. annexB997E30-M2x-NUS0(19) - Class 997E30-M2x Annex B: 997E30-M2x-NUS0 20. annexB998E17-M2x-NUS0(20) - Class 998E17-M2x Annex B: 998E17-M2x-NUS0, 998E17-M2x-NUS0-M 21. annexB998E17-M2x-NUS0-M(21) - Class 998E17-M2x Annex B: 998E17-M2x-NUS0, 998E17-M2x-NUS0-M 22. annexB998ADE17-M2x-NUS0-M(22) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M. 23. annexB998ADE17-M2x-B(23) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M. 24. annexB998E30-M2x-NUS0(24) - Class 998E30-M2x Annex B: 998E30-M2x-NUS0, 998E30-M2x-NUS0-M 25. annexB998E30-M2x-NUS0-M(25) - Class 998E30-M2x Annex B: 998E30-M2x-NUS0, 998E30-M2x-NUS0-M 26. annexB998ADE30-M2x-NUS0-M(26) - Class 998ADE30-M2x Annex B: 998ADE30-M2x-NUS0-M, 998ADE30-M2x-NUS0-A 27. annexB998ADE17-M2x-A(27) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M. 28. annexB998ADE30-M2x-NUS0-A(28) - Class 998ADE30-M2x Annex B: 998ADE30-M2x-NUS0-M, 998ADE30-M2x-NUS0-A 29. annexA998-D-48(29) - Class 998 Annex A: D-32, D-64, D-48, D-128 30. annexA998-D-128(30) - Class 998 Annex A: D-32, D-64, D-48, D-128 31. annexB998ADE17-M2x-M(31) - Class 998ADE17-M2x Annex B: 998ADE17-M2x-NUS0-M, 998ADE17-M2x-A, 998ADE17-M2x-B, 998ADE17-M2x-M. 32. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfLimitMask	1.3.6.1.2.1.10.94.1.1.65550.1.44	INTEGER	read-create	This configuration parameter contains the G.993.2 profiles to be allowed by the near-end xTU on this line. Options: 1. profile8a (1) - The G.993.2 profile is profile8a 2. profile8b (2) - The G.993.2 profile is profile8b 3. profile8c (3) - The G.993.2 profile is profile8c 4. profile8d (4) - The G.993.2 profile is profile8d 5. profile12a (5) - The G.993.2 profile is profile12a 6. profile12b (6) - The G.993.2 profile is profile12b 7. profile17a (7) - The G.993.2 profile is profile17a 8. profile30a (8) - The G.993.2 profile is profile30a 9. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfUpboKLF	1.3.6.1.2.1.10.94.1.1.65550.1.31	INTEGER	read-create	This parameter is a flag that forces the VTU-R to use the electrical loop length of the CO-MIB (UPBOKL) to compute the UPBO. The value shall be forced if the flag is set to 1. Otherwise, the electrical loop length shall be autonomously selected by the VTU-O. Options: 1. forced(1) - Force the CPE to use the electrical length of the CO(UPBOKL) to compute the UPBO 2. auto(2) - Electrical length shall be autonomously selected by the CO 3. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfVirtualNoiseModeDs	1.3.6.1.2.1.10.94.1.1.65550.1.47	INTEGER	read-create	Defines the Virtual Noise of downsteam. Options: 1. disable(1) - Unused 2. enable(2) - Used 3. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfVirtualNoiseModeUs	1.3.6.1.2.1.10.94.1.1.65550.1.48	INTEGER	read-create	Defines the Virtual Noise of upstream. Options: 1. disable(1) - Unused 2. enable(2) - Used 3. invalidValue(-1) - Invalid value
INT hwxdslDynamicProfXdslMode	1.3.6.1.2.1.10.94.1.1.65550.1.37	INTEGER	read-create	The XDSL Mode is a way of categorizing the various XDSL transmission modes into groups, each group (XDSL Mode) shares the same PSD configuration. Options: 1. defMode (1) - XDSL transmit mode is defMode 2. adsl (2) - XDSL transmit mode is adsl 3. adsl2Pots (3) - XDSL transmit mode is adsl2Pots 4. adsl2Isdn (4) - XDSL transmit mode is adsl2Isdn 5. adsl2PlusPots (5) - XDSL transmit mode is adsl2PlusPots 6. adsl2PlusIsdn (6) - XDSL transmit mode is adsl2PlusIsdn 7. adsl2ReachExtended (7) - XDSL transmit mode is adsl2ReachExtended 8. g9923PotsNonOverlapped(8) - XDSL transmit mode is g9923PotsNonOverlapped 9. g9923PotsOverlapped(9) - XDSL transmit mode is g9923PotsOverlapped 10. g9923IsdnNonOverlapped(10) - XDSL transmit mode is g9923IsdnNonOverlapped 11. g9923isdnOverlapped(11) - XDSL transmit mode is g9923isdnOverlapped 12. g9924potsNonOverlapped(14) - XDSL transmit mode is g9924potsNonOverlapped 13. g9924potsOverlapped(15) - XDSL transmit mode is g9924potsOverlapped 14. g9923AnnexIAllDigNonOverlapped(18) - XDSL transmit mode is g9923AnnexIAllDigNonOverlapped 15. g9923AnnexIAllDigOverlapped(19) - XDSL transmit mode is g9923AnnexIAllDigOverlapped 16. g9923AnnexJAllDigNonOverlapped(20) - XDSL transmit mode is g9923AnnexJAllDigNonOverlapped 17. g9923AnnexJAllDigOverlapped(21) - XDSL transmit mode is g9923AnnexJAllDigOverlapped 18. g9924AnnexIAllDigNonOverlapped(22) - XDSL transmit mode is g9924AnnexIAllDigNonOverlapped 19. g9924AnnexIAllDigOverlapped(23) - XDSL transmit mode is g9924AnnexIAllDigOverlapped 20. g9923AnnexLMode1NonOverlapped(24) - XDSL transmit mode is g9923AnnexLMode1NonOverlapped 21. g9923AnnexLMode2NonOverlapped(25) - XDSL transmit mode is g9923AnnexLMode2NonOverlapped 22. g9923AnnexLMode3Overlapped(26) - XDSL transmit mode is g9923AnnexLMode3Overlapped 23. g9923AnnexLMode4Overlapped(27) - XDSL transmit mode is g9923AnnexLMode4Overlapped 24. g9923AnnexMPotsNonOverlapped(28) - XDSL transmit mode is g9923AnnexMPotsNonOverlapped 25. g9923AnnexMPotsOverlapped(29) - XDSL transmit mode is g9923AnnexMPotsOverlapped 26. g9925PotsNonOverlapped(30) - XDSL transmit mode is g9925PotsNonOverlapped 27. g9925PotsOverlapped(31) - XDSL transmit mode is g9925PotsOverlapped 28. g9925IsdnNonOverlapped(32) - XDSL transmit mode is g9925IsdnNonOverlapped 29. g9925isdnOverlapped(33) - XDSL transmit mode is g9925isdnOverlapped 30. g9925AnnexIAllDigNonOverlapped(36) - XDSL transmit mode is g9925AnnexIAllDigNonOverlapped 31. g9925AnnexIAllDigOverlapped(37) - XDSL transmit mode is g9925AnnexIAllDigOverlapped 32. g9925AnnexJAllDigNonOverlapped(38) - XDSL transmit mode is g9925AnnexJAllDigNonOverlapped 33. g9925AnnexJAllDigOverlapped(39) - XDSL transmit mode is g9925AnnexJAllDigOverlapped 34. g9925AnnexMPotsNonOverlapped(40) - XDSL transmit mode is g9925AnnexMPotsNonOverlapped 35. g9925AnnexMPotsOverlapped(41) - XDSL transmit mode is g9925AnnexMPotsOverlapped 36. vdsl2Pots (42) - XDSL transmit mode is vdsl2Pots 37. vdsl2Isdn (43) - XDSL transmit mode is vdsl2Isdn 38. invalidValue(-1) - Invalid value
INT hwXdslPortFarEndRunState	1.3.6.1.2.1.10.94.1.1.65538.1.600	INTEGER	read-only	Xdsl port far end Run state, This object is defaulted unknown(1). Options: 1. unknown(1) - Unknown status 2. noModem(2) - Port is not connected to modem 3. handshake(3) - Handshake status 4. showtime(4) - Port is activated
INT hwXdslPortIopCaptureOperStatus	1.3.6.1.2.1.10.94.1.1.65551.1.2	INTEGER	read-only	Port IOP capture status. Options: 1. noCapture(1) - Indicates that the capture is not performed 2. capturing(2) - Indicates that the capture is being performed 3. iopGenerate(3) - Indicates that the IOP file is generated 4. captured(4) - Indicates that the capture is complete 5. invalid(-1) - Invalid value
INT hwXdslPortIopCaptureOperType	1.3.6.1.2.1.10.94.1.1.65551.1.1	INTEGER	read-write	Start or stop IOP information capture of xDSL port. Options: 1. start(1) - Start IOP information capture of xDSL port 2. stop(2) - Stop IOP information capture of xDSL port 3. invalid(-1) - Invalid value
INT hwXdslPortLoopFlag	1.3.6.1.2.1.10.94.1.1.65538.1.800	INTEGER	read-only	Loop flag. Options: 1. false(0) - No loop 2. true (1) - Loop
INT hwXdslPortNTEPowerStatus	1.3.6.1.2.1.10.94.1.1.65538.1.8	INTEGER	read-only	NTE power status, this object is defaulted off(2). Options: 1. on(1) - NTE power on 2. off(2) - NTE power off 3. unknown(3) - Unknown status
INT hwXdslPortPowerState	1.3.6.1.2.1.10.94.1.1.65538.1.601	INTEGER	read-only	Xdsl port power state. Options: 1. l0(1) - Full-on state 2. l2(2) - Low power state 3. l3(3) - Idle state 4. l1(4) - Low power state 5. invalidValue(-1) - Invalid value Default: l0(1)
INT hwXdslPortRateMonitorAlarmEnable	1.3.6.1.2.1.10.94.1.1.65538.1.6	INTEGER	read-write	Enables/Disables port rate monitor alarm. Options: 1. enabled(1) - The port rate monitor alarm is enabled 2. disabled(2) - The port rate monitor alarm is disabled
INT hwXdslPortUpCntAdminStatus	1.3.6.1.2.1.10.94.1.1.65538.1.701	INTEGER	read-write	Admin the up counts of xDSL port. Options: 1. reset(0) - Reset the up counts of xDSL port
Integer32 (50)
I32 hwadsl2L2ModeGuardTime	1.3.6.1.2.1.10.94.1.1.65543.1.27	Integer32	read-create	Guard Time before entering L2 Mode. Range: 0-1024 Default: 60 Unit: seconds
I32 hwadsl2L2ModeIntervalPowerValue	1.3.6.1.2.1.10.94.1.1.65543.1.29	Integer32	read-create	Maximum aggregate transmit power reduction per L2 request or L2 power trim. Range: 0-31 Default: 3 Unit: db
I32 hwadsl2L2ModeIntervalTime	1.3.6.1.2.1.10.94.1.1.65543.1.28	Integer32	read-create	The minimum interval between two records of L2 mode. Range: 0-255 Default: 255 Unit: seconds
I32 hwadsl2L2ModeL2Time	1.3.6.1.2.1.10.94.1.1.65543.1.65536	Integer32	read-create	This minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. It ranges from 0 to 255 seconds. Range: 0-255 Default: 30 Unit: seconds
I32 hwadsl2L2ModeMaxDataRate	1.3.6.1.2.1.10.94.1.1.65543.1.25	Integer32	read-create	Maximum Data Rate in L2 Mode. Range: 128-16384 Default: 1024 Unit: Kbps
I32 hwadsl2L2ModeMinDataRate	1.3.6.1.2.1.10.94.1.1.65543.1.24	Integer32	read-create	Minimum Data Rate in L2 Mode. Range: 128-16384 Unit: Kbps
I32 hwadsl2L2ModePayloadRateThreshold	1.3.6.1.2.1.10.94.1.1.65543.1.26	Integer32	read-create	Threshold for the Payload Rate Ratio. Range: 128-16384 Default: 128 Unit: Kbps
I32 hwadsl2L2ModeTotalPowerValue	1.3.6.1.2.1.10.94.1.1.65543.1.30	Integer32	read-create	Total maximum aggregate transmit power reduction in L2. Range: 0-31 Default: 9 Unit: db
I32 hwAdslAtucCurrSnrMgn	1.3.6.1.2.1.10.94.1.1.65546.1.16	Integer32	read-only	Noise Margin as seen by this ATU with respect to its received signal in tenth dB. Unit: tenth dB
I32 hwAdslAtucLatestSnrMgn	1.3.6.1.2.1.10.94.1.1.65544.1.5	Integer32	read-only	Noise Margin as seen by this ATU-C at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
I32 hwAdslAtucLatestTargetSnrMgn	1.3.6.1.2.1.10.94.1.1.65544.1.15	Integer32	read-only	Port Signal/Noise Margin. Range: 0-310 Unit: tenth dB
I32 hwAdslAtucPrevSnrMgn	1.3.6.1.2.1.10.94.1.1.65539.1.1	Integer32	read-only	Noise Margin as seen by this ATU-C at the time of the last adslAtucRateChangeTrap event. Unit: tenth dB
I32 hwAdslAturCurrSnrMgn	1.3.6.1.2.1.10.94.1.1.65546.1.20	Integer32	read-only	Noise Margin as seen by this ATU with respect to its received signal in tenth dB. Unit: tenth dB
I32 hwAdslAturLatestSnrMgn	1.3.6.1.2.1.10.94.1.1.65544.1.6	Integer32	read-only	Noise Margin as seen by this ATU-R at the time of the last adslAtucRateChangeTrap event. in tenth dB. Unit: tenth dB
I32 hwAdslAturLatestTargetSnrMgn	1.3.6.1.2.1.10.94.1.1.65544.1.16	Integer32	read-only	Port Signal/Noise Margin. Range: 0-310 Unit: tenth dB
I32 hwAdslAturPrevSnrMgn	1.3.6.1.2.1.10.94.1.1.65539.1.2	Integer32	read-only	Noise Margin as seen by this ATU-R at the time of the last adslAtucRateChangeTrap event. Unit: tenth dB
I32 hwAdslExtDsMaxPsd	1.3.6.1.2.1.10.94.1.1.65543.1.18	Integer32	read-create	Maximum PSD margin in downstream.
I32 hwadslExtDsMinRSoverhead	1.3.6.1.2.1.10.94.1.1.65543.1.38	Integer32	read-write	The minimum value of R/N on downstream direction. Range: 0-128 Default: 0 Unit: 1/256
I32 hwadslExtDsMinRtxRatio	1.3.6.1.2.1.10.94.1.1.65543.1.37	Integer32	read-write	Minimum rtxratio on downstream direction. Range: 0-255 Default: 0 Unit: 1/256
I32 hwAdslExtDsMinTrainSnrMgn	1.3.6.1.2.1.10.94.1.1.65543.1.16	Integer32	read-create	Maximum Trainning Margin in downstream. Range: 0-310 Default: 30 Unit: tenth dB
I32 hwadslExtUsMinRSoverhead	1.3.6.1.2.1.10.94.1.1.65543.1.34	Integer32	read-write	The minimum value of R/N on upstream direction. Range: 0-128 Default: 0 Unit: 1/256
I32 hwadslExtUsMinRtxRatio	1.3.6.1.2.1.10.94.1.1.65543.1.33	Integer32	read-write	Minimum rtxratio on upstream direction. Range: 0-255 Default: 0 Unit: 1/256
I32 hwAdslExtUsMinTrainSnrMgn	1.3.6.1.2.1.10.94.1.1.65543.1.17	Integer32	read-create	Maximum Trainning Margin in upstream. Range: 0-310 Default: 30 Unit: tenth dB
I32 hwadslLineDisableToneSection1Begin	1.3.6.1.2.1.10.94.1.1.65543.1.2	Integer32	read-create	The begin index of section1. Range: 0-511
I32 hwadslLineDisableToneSection1End	1.3.6.1.2.1.10.94.1.1.65543.1.3	Integer32	read-create	The end index of section1. Range: 0-511
I32 hwadslLineDisableToneSection2Begin	1.3.6.1.2.1.10.94.1.1.65543.1.5	Integer32	read-create	The begin index of section2. Range: 0-511
I32 hwadslLineDisableToneSection2End	1.3.6.1.2.1.10.94.1.1.65543.1.6	Integer32	read-create	The end index of section2. Range: 0-511
I32 hwadslLineDisableToneSection3Begin	1.3.6.1.2.1.10.94.1.1.65543.1.8	Integer32	read-create	The begin index of section3. Range: 0-511
I32 hwadslLineDisableToneSection3End	1.3.6.1.2.1.10.94.1.1.65543.1.9	Integer32	read-create	The end index of section3. Range: 0-511
I32 hwadslLineDisableToneSection4Begin	1.3.6.1.2.1.10.94.1.1.65543.1.11	Integer32	read-create	The begin index of the fourth section. Range: 0-511
I32 hwadslLineDisableToneSection4End	1.3.6.1.2.1.10.94.1.1.65543.1.12	Integer32	read-create	The end index of the fourth section. Range: 0-511
I32 hwAdslLineDownStreamBitsPerFrame	1.3.6.1.2.1.10.94.1.1.65537.1.1	Integer32	read-only	Number of bits required per frame in the downstream data path for the current configuration.
I32 hwAdslLinePvcDsBand	1.3.6.1.2.1.10.94.1.1.65536.1.5	Integer32	read-write	The down stream band of the adsl line PVC. Range: 0-450
I32 hwAdslLinePvcIndex	1.3.6.1.2.1.10.94.1.1.65536.1.9	Integer32	read-write	The index of the adsl line PVC. Range: 1-8
I32 hwAdslLinePvcPriority	1.3.6.1.2.1.10.94.1.1.65536.1.4	Integer32	read-write	The Priority value of the adsl line PVC. Range: 0-7
I32 hwAdslLinePvcUsBand	1.3.6.1.2.1.10.94.1.1.65536.1.6	Integer32	read-write	The up stream band of the adsl line PVC. Range: 0-450
I32 hwAdslLinePvcVci	1.3.6.1.2.1.10.94.1.1.65536.1.2	Integer32	read-only	The VCI of the adsl line.
I32 hwAdslLinePvcVlanId	1.3.6.1.2.1.10.94.1.1.65536.1.3	Integer32	read-write	The VLAN ID of the adsl line PVC. Range: 1-4000
I32 hwAdsllinePvcVpi	1.3.6.1.2.1.10.94.1.1.65536.1.1	Integer32	read-only	The VPI of the adsl line.
I32 hwAdslLineUpStreamBitsPerFrame	1.3.6.1.2.1.10.94.1.1.65537.1.2	Integer32	read-only	Number of bits required per frame in the upstream data path for the current configuration.
I32 hwAdslPort15minutesPerformanceInterval	1.3.6.1.2.1.10.94.1.1.65546.1.1	Integer32	not-accessible	The index of the interval which is queried. Range: 0-96
I32 hwxdslDynamicProfMaxNomPsdDs	1.3.6.1.2.1.10.94.1.1.65550.1.38	Integer32	read-create	The maximum nominal transmit PSD in the downstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz(physical values are -60 to -30 dBm/Hz). The invalid value is -1. If data is invalid, the invalid value will be returned. Unit: 0.1 dB
I32 hwxdslDynamicProfMaxNomPsdUs	1.3.6.1.2.1.10.94.1.1.65550.1.39	Integer32	read-create	The maximum nominal transmit PSD in the upstream direction during initialization and Showtime. It ranges from -600 to -300 units of 0.1 dBm/Hz(physical values are -60 to -30 dBm/Hz). The invalid value is -1. If data is invalid, the invalid value will be returned. Unit: 0.1 dB
I32 hwXdslPort15minutesPerformanceInterval	1.3.6.1.2.1.10.94.1.1.65545.1.1	Integer32	not-accessible	The index of the interval which is queried. Range: 0-96
I32 hwXdslPortCurrentDownRate	1.3.6.1.2.1.10.94.1.1.65538.1.501	Integer32	accessible-for-notify	Xdsl Port Current Downstream Value. Range: 0-30000 Default: 0
I32 hwXdslPortCurrentUpRate	1.3.6.1.2.1.10.94.1.1.65538.1.500	Integer32	accessible-for-notify	Xdsl Port Current Upstream Value. Range: 0-30000 Default: 0
I32 hwXdslPortDownThreshold	1.3.6.1.2.1.10.94.1.1.65538.1.811	Integer32	read-write	Set Port monitoring downstream rate threshold percent value. Range: 0-100
I32 hwXdslPortMaxMacLearn	1.3.6.1.2.1.10.94.1.1.65538.1.1	Integer32	read-write	Set Max MAC count on the XDSL port. Range: 0-255 Default: 255
I32 hwXdslPortRateMonitorThreshold	1.3.6.1.2.1.10.94.1.1.65538.1.2	Integer32	read-write	Set Port monitoring rate threshold percent. Including upstream and downstream. Range: 0-100 Default: 0
I32 hwXdslPortUpThreshold	1.3.6.1.2.1.10.94.1.1.65538.1.810	Integer32	read-write	Set Port monitoring upstream rate threshold percent value. Range: 0-100
OCTET STRING (31)
OCT hwAdsl2SCStatusBitsAlloc	1.3.6.1.2.1.10.94.1.1.65549.1.3	OCTET STRING	read-only	The bits allocation per sub-carrier. An array of 256 octets (512 nibbles), designed for supporting up to 512 (downstream) sub-carriers. The number of utilized nibbles on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Nibble i (0 <= i < NSC) is set to a value in the range 0 to 15 to indicate that the respective downstream or upstream sub-carrier i has the same amount of bits allocation.
OCT hwAdsl2SCStatusGainAlloc	1.3.6.1.2.1.10.94.1.1.65549.1.4	OCTET STRING	read-only	The gain allocation per sub-carrier. An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub- carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Value i (0 <= i < NSC) is in the range 0 to 4093 to indicate that the respective downstream or upstream sub-carrier i has the same amount of gain value. The gain value is represented as a multiple of 1/512 on a linear scale. Each value in this array is 16 bits wide and is stored in big endian format.
OCT hwAdsl2SCStatusLog	1.3.6.1.2.1.10.94.1.1.65549.1.5	OCTET STRING	read-only	An array of up to 512 real H(f) logarithmic representation values in dB for the respective transmission direction. It is designed to support up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Each array entry represents the real Hlog(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NSC). The real Hlog(f) value is represented as (6-m(i)/10), with m(i) in the range 0 to 1022. A special value m=1023 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the attenuation is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 16 bits wide and is stored in big endian format.
OCT hwAdsl2SCStatusQln	1.3.6.1.2.1.10.94.1.1.65549.1.6	OCTET STRING	read-only	An array of up to 512 real Quiet Line Noise values in dBm/Hz for the respective transmission direction. It is designed for up to 512 (downstream) sub-carriers. The number of utilized values on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Each array entry represents the QLN(f = i*Df) value for a particular sub-carrier index i, (0 <= i < NSC). The QLN(f) is represented as ( -23-n(i)/2), with n(i) in the range 0 to 254. A special value n(i)=255 indicates that no measurement could be done for the subcarrier because it is out of the passband or that the noise PSD is out of range to be represented. This parameter is applicable in loop diagnostic procedure and initialization. Each value in this array is 8 bits wide.
OCT hwAdsl2SCStatusSnr	1.3.6.1.2.1.10.94.1.1.65549.1.2	OCTET STRING	read-only	The SNR Margin per sub-carrier, expressing the ratio between the received signal power and received noise power per subscriber. It is an array of 512 octets, designed for supporting up to 512 (downstream) sub-carriers. The number of utilized octets on downstream direction depends on NSCds, and on upstream direction it depends on NSCus. This value is referred to here as NSC. Octet i (0 <= i < NSC) is set to a value in the range 0 to 254 to indicate that the respective downstream or upstream sub- carrier i has SNR of: (-32 + Adsl2SubcarrierSnr(i)/2) in dB (i.e., -32 to 95dB). The special value 255 means that no measurement could be done for the subcarrier because it is out of the PSD mask passband or that the noise PSD is out of range to be represented. Each value in this array is 8 bits wide.
OCT hwAdsl2SCStatusSnrMargin	1.3.6.1.2.1.10.94.1.1.65549.1.7	OCTET STRING	read-only	SNR Margin is the maximum increase in dB of the noise power received at the ATU (ATU-R on downstream direction and ATU-C on upstream direction), such that the BER requirements are met for all bearer channels received at the ATU. It ranges from -640 to 630 units of 0.1 dB (physical values are -64 to 63 dB).
OCT hwAdsl2SCStatusTxPSD	1.3.6.1.2.1.10.94.1.1.65549.1.8	OCTET STRING	read-only	The PSD MASK per sub-carrier.An array of 512 16-bits values, designed for supporting up to 512 (downstream) sub-carriers. It ranges from -1400 to -300 units of 0.1 dBm/Hz (physical values are -140 to -30 dBm/Hz).
OCT hwAdslLineConfProfile	1.3.6.1.2.1.10.94.1.1.65546.1.13	OCTET STRING	read-only	The value of this object identifies the row in the ADSL Line Configuration Profile Table, (adslLineConfProfileTable), which applies for this ADSL line, and channels if applicable. For 'dynamic' mode, in the case which the configuration profile has not been set, the value will be set to 'DEFVAL'. If the creator of this MIB has chosen not to implement 'dynamic assignment' of profiles, this object's MIN-ACCESS is read-only.
OCT hwAdslLineDownStreamBitAllocHigh	1.3.6.1.2.1.10.94.1.1.65537.1.4	OCTET STRING	read-only	when used to Adsl board This object contains the second 128 downstream sub-carrier bit allocations (sub-carrier # 129-256). This object is 64 bytes in length, where each byte contains 2 sub-carrier values. Byte 1 - 64 Downstream bit allocation (second 128 sub-carriers), one byte for two sub-carriers. 1 Bits 4 - 7 # bits in 129th downstream sub-carrier 1 Bits 0 - 3 # bits in 130th downstream sub-carrier ... 64 Bits 4 - 7 # bits in 255th downstream sub-carrier 64 Bits 0 - 3 # bits in 256th downstream sub-carrier when used to Adsl2+ board This object contains the second 256 downstream sub-carrier bit allocations (sub-carrier # 257-512). This object is 256 bytes in length, where each byte contains 1 sub-carrier values. Byte 1 - 256 Downstream bit allocation (second 256 sub-carriers), one byte for one sub-carriers. 1 Bits 0 - 7 # bits in 1st downstream sub-carrier ... 255 Bits 0 - 7 # bits in 255th downstream sub-carrier 256 Bits 0 - 7 # bits in 256th downstream sub-carrier
OCT hwAdslLineDownStreamBitAllocLow	1.3.6.1.2.1.10.94.1.1.65537.1.3	OCTET STRING	read-only	when used to Adsl board This object contains the first 128 downstream sub-carrier bit allocations (sub-carrier # 1-128). This object is 64 bytes in length, where each byte contains 2 sub-carrier values. Byte 1 - 64 Downstream bit allocation (first 128 sub-carriers), one byte for two sub-carriers. 1 Bits 4 - 7 # bits in 1st downstream sub-carrier 1 Bits 0 - 3 # bits in 2nd downstream sub-carrier ... 64 Bits 4 - 7 # bits in 127th downstream sub-carrier 64 Bits 0 - 3 # bits in 128th downstream sub-carrier when used to Adsl2+ board This object contains the first 256 downstream sub-carrier bit allocations (sub-carrier # 1-256). This object is 256 bytes in length, where each byte contains 1 sub-carrier values. Byte 1 - 256 Downstream bit allocation (first 256 sub-carriers), one byte for one sub-carriers. 1 Bits 0 - 7 # bits in 1st downstream sub-carrier ... 255 Bits 0 - 7 # bits in 255th downstream sub-carrier 256 Bits 0 - 7 # bits in 256th downstream sub-carrier
OCT hwadslLineDynamicProfile	1.3.6.1.2.1.10.94.1.1.1.1.65537	OCTET STRING	read-write	The value of this object identifies the row in the ADSL Dynamic Profile Table,which applies to this ADSL line, and channels if applicable. NULL - indicates that there is no Dynamic profile bound to this port. Range: 0-32
OCT hwadslLineExtConfProfile	1.3.6.1.2.1.10.94.1.1.1.1.65536	OCTET STRING	read-write	The value of this object identifies the row in the ADSL Extend Line Configuration Profile Table, (adslLineExtConfProfileTable), which applies to this ADSL line, and channels if applicable. NULL - indicates that there is no extend line profile bound to this port. Range: 0-32
OCT hwadslLineExtConfProfileName	1.3.6.1.2.1.10.94.1.1.65543.1.1	OCTET STRING	not-accessible	This object is used by the hwadslLineExtConfProfileTable in order to identify a row of this table. This object indicates the name of the extended line profile.
OCT hwAdslLineUpStreamBitAlloc	1.3.6.1.2.1.10.94.1.1.65537.1.5	OCTET STRING	read-only	when used to Adsl board This Object contains 64 upstream sub-carrier bit allocations (sub-carrier # 1-64). This Object is 32 bytes in length, where each byte contains 2 sub-carrier values. Byte 1-32 Upstream bit allocation information, total: 32 bytes, one byte for two sub-carriers. 1 Bits 7 - 4 # bits in 1st upstream sub-carrier 1 Bits 3 - 0 # bits in 2nd upstream sub-carrier ... 32 Bits 7 - 4 # bits in 63rd upstream sub-carrier 32 Bits 3 - 0 # bits in 64th upstream sub-carrier when used to Adsl2+ board This Object contains 64 upstream sub-carrier bit allocations (sub-carrier # 1-64). This Object is 64 bytes in length, where each byte contains 1 sub-carrier values. Byte 1-64 Upstream bit allocation information, total: 64 bytes, one byte for one sub-carriers. 1 Bits 7 - 0 # bits in 1st upstream sub-carrier ... 64 Bits 7 - 0 # bits in 64th upstream sub-carrier
OCT hwAdslPortRateChangeTrapDslType	1.3.6.1.2.1.10.94.1.1.65547.1.7	OCTET STRING	accessible-for-notify	DSL line type of the port whose rate changes.
OCT hwAdslPortRateChangeTrapEventType	1.3.6.1.2.1.10.94.1.1.65547.1.6	OCTET STRING	accessible-for-notify	Event type reported during the previous change of the rate. If both the upstream and downstream rates change, this leaf object outputs character string 'DU'. If only the upstream rates changes, this leaf object outputs character string 'US'. If only the downstream rates changes, this leaf object outputs character string 'DS'.
OCT hwAdslPortRateChangeTrapIPIAID	1.3.6.1.2.1.10.94.1.1.65547.1.1	OCTET STRING	accessible-for-notify	The port IPIAID is reported when the port rate changes.
OCT hwAdslPortRateChangeTrapMUXID	1.3.6.1.2.1.10.94.1.1.65547.1.2	OCTET STRING	accessible-for-notify	The port MUXID is reported when the port rate changes.
OCT hwxdslDynamicProfCarMaskDS	1.3.6.1.2.1.10.94.1.1.65550.1.35	OCTET STRING	read-create	Sub-carriers mask. A bitmap of 512 bits that allows masking up to 512 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCds) is set to '1', the respective downstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCds < 512, all bits i (NSCds i <= 512) should be set to '1'.
OCT hwxdslDynamicProfCarMaskUS	1.3.6.1.2.1.10.94.1.1.65550.1.36	OCTET STRING	read-create	Sub-carriers mask. A bitmap of 64 bits that allows masking up to 64 downstream sub-carriers, depending on NSCds. If bit i (0 <= i < NSCus) is set to '1', the respective upstream sub-carrier i is masked, and if set to '0', the respective sub-carrier is unmasked. Note that there should always be unmasked sub-carriers (i.e., the object cannot be all 1's). Also note that if NSCus < 64, all bits i (NSCus < i <= 64) should be set to '1'.
OCT hwxdslDynamicProfDpboEPsd	1.3.6.1.2.1.10.94.1.1.65550.1.24	OCTET STRING	read-create	This parameter defines the PSD mask that is assumed to be permitted at the exchange. This parameter shall use the same format as PSDMASKds. The maximum number of breakpoints for DPBOEPSD is 16. This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 1 and NSCds. Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value 0xff.
OCT hwxdslDynamicProfDpboEscm	1.3.6.1.2.1.10.94.1.1.65550.1.26	OCTET STRING	read-create	This configuration parameter defines a cable model in terms of three scalars DPBOESCMA, DPBOESCMB and DPBOESCMC that shall be used to describe the frequency dependent loss of E-side cables.Parameters DPBOESCMA, DPBOESCMB, DPBOESCMC shall be coded as unsigned integers representing a scalar value from -1 (coded as 0) to 1.5 (coded as 640) in step of 1/256. All values in the range are valid. Octets 0+1 DPBOESCMA Octets 2+3 DPBOESCMB Octets 4+5 DPBOESCMC
OCT hwxdslDynamicProfProfileName	1.3.6.1.2.1.10.94.1.1.65550.1.1	OCTET STRING	not-accessible	The name of xdsl Dynamic Profile.
OCT hwxdslDynamicProfPsdMaskDs	1.3.6.1.2.1.10.94.1.1.65550.1.42	OCTET STRING	read-create	This configuration parameter defines the downstream PSD mask applicable at the U C2 reference point. This MIB PSD mask may impose PSD restrictions in addition to the Limit PSD mask defined in the relevant Recommendation (e.g., G.992.5, G.993.2). This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCds - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 32, all remaining octets are set to the value 0xff. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
OCT hwxdslDynamicProfPsdMaskUs	1.3.6.1.2.1.10.94.1.1.65550.1.43	OCTET STRING	read-create	This configuration parameter defines the upstream PSD mask applicable at the U R2 reference point. This MIB PSD mask may impose PSD restrictions in addition to the Limit PSD mask defined in the relevant Recommendations (e.g., ITU-T Recommendations G.992.3, G.993.2). This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 45-47 - Same, for a 3rd breakpoint. This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCus - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (-127.5dBm/Hz) with steps of 0.5dBm/Hz. Valid values are in the range 0 to 190 (0 to -95dBm/Hz). When the number of breakpoints is less than 16, all remaining octets are set to the value 0xff. Note that the content of this object should be correlated with the sub-carriers mask and with the RFI setup.
OCT hwxdslDynamicProfRfiBands	1.3.6.1.2.1.10.94.1.1.65550.1.33	OCTET STRING	read-create	The subset of PSD mask breakpoints that shall be used to notch an RFI band. It is a string of bands consist of begin tone index and end tone index. for example :0-10,20-50,100-4095 It can contain as most as 16 bands.
OCT hwxdslDynamicProfToneBlackOut	1.3.6.1.2.1.10.94.1.1.65550.1.34	OCTET STRING	read-create	The subset of subcarriermask that shall be used to mask the subcarriers. It is a string of bands consist of begin tone index and end tone index. for example :0-10,20-50,100-4095 It can contain as most as 8 bands.
OCT hwxdslDynamicProfUpboPsdBand	1.3.6.1.2.1.10.94.1.1.65550.1.30	OCTET STRING	read-create	This parameter defines the UPBO reference PSD used to compute the upstream power back-off for each upstream band except US0. A UPBOPSD defined for each band ahsll consist of two parameters [a, b]. Parameter a shall be coded as an unsigned 12-bit number from 40 dBm/Hz (coded as 0) to 80.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz; and b shall be coded as an unsigned 12 bit number from 0 (coded as 0) to 40.95 dBm/Hz (coded as 4095) in steps of 0.01 dBm/Hz. The UPBO reference PSD at the frequency f expressed in MHz shall be equal to '-a-b(SQRT(f))'. The set of parameter values a = 40 dBm/Hz, b = 0 dBm/Hz is a special configuration to disable UPBO in the respective upstream band. Octets 0+1 - a[0] Octets 2+3 - b[0] Octets 4+5 - a[1] Octets 6+7 - b[1] Octets 8+9 - a[2] Octets 10+11 - b[2] Octets 12+13 - a[3] Octets 14+15 - b[3]
OCT hwxdslDynamicProfVirtualNoiseDs	1.3.6.1.2.1.10.94.1.1.65550.1.49	OCTET STRING	read-create	The Virtual Noise of downsteam. This is a string of 32 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 94-95, which are associated with a 32nd breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCds - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (127.5dBm/Hz) with steps of 0.5dBm/Hz.
OCT hwxdslDynamicProfVirtualNoiseUs	1.3.6.1.2.1.10.94.1.1.65550.1.50	OCTET STRING	read-create	The Virtual Noise of upsteam. This is a string of 16 pairs of values in the following structure: Octets 0+1 - Index of 1st sub-carrier used in the context of a first breakpoint. Octet 2 - The PSD reduction for the sub-carrier indicated in octets 0 and 1. Octets 3-5 - Same, for a 2nd breakpoint. Octets 6-8 - Same, for a 3rd breakpoint. This architecture continues until octets 45-47, which are associated with a 16th breakpoint. Each subcarrier index is an unsigned number in the range 0 and (NSCds - 1). Each PSD reduction value is in the range 0 (0dBm/Hz) to 255 (127.5dBm/Hz) with steps of 0.5dBm/Hz.
OCT hwXdslPortStateBitmapList	1.3.6.1.2.1.10.94.1.1.65542.1.2	OCTET STRING	read-only	The type of port status: 2 failed; 8 testing; 9 activated; 10 activating; 11 deactivated; 18 localloopback; 19 remoteloopback; 20 blocked; 37 utopialoopback; 38 afeloopback; 39 hybridloopback; 255 unknown; HwXdslPortStateBitmapList describes the states of all ports. Every byte describe the current state of every port. The length is equal to the value of the hwXdslPortStatePortNumber.
PerfIntervalCount (27)
NUM hwAdslAtucChanIntervalCorrectedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.34	PerfIntervalCount	read-only	Count of all blocks received with errors that were corrected on this channel during this interval.
NUM hwadslAtucChanIntervalCrcBlks	1.3.6.1.2.1.10.94.1.1.12.1.65538	PerfIntervalCount	read-only	Count of all blocks received with CRC anomalies on this channel during this interval.
NUM hwadslAtucChanIntervalFecBlks	1.3.6.1.2.1.10.94.1.1.12.1.65536	PerfIntervalCount	read-only	Count of all blocks received with FRC anomalies on this channel during this interval.
NUM hwadslAtucChanIntervalHecBlks	1.3.6.1.2.1.10.94.1.1.12.1.65537	PerfIntervalCount	read-only	Count of all blocks received with HRC anomalies on this channel during this interval.
NUM hwAdslAtucChanIntervalReceivedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.32	PerfIntervalCount	read-only	Count of all encoded blocks received on this channel during this interval.
NUM hwAdslAtucChanIntervalTransmittedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.33	PerfIntervalCount	read-only	Count of all encoded blocks transmitted on this channel during this interval.
NUM hwAdslAtucChanIntervalUncorrectBlks	1.3.6.1.2.1.10.94.1.1.65546.1.35	PerfIntervalCount	read-only	Count of all blocks received with uncorrectable errors on this channel during this interval.
NUM hwAdslAtucIntervalESs	1.3.6.1.2.1.10.94.1.1.65546.1.23	PerfIntervalCount	read-only	Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects. Unit: seconds
NUM hwAdslAtucIntervalLofs	1.3.6.1.2.1.10.94.1.1.65546.1.24	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Framing. Unit: seconds
NUM hwAdslAtucIntervalLols	1.3.6.1.2.1.10.94.1.1.65546.1.25	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Link. Unit: seconds
NUM hwAdslAtucIntervalLoss	1.3.6.1.2.1.10.94.1.1.65546.1.26	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Signal. Unit: seconds
NUM hwAdslAtucIntervalLprs	1.3.6.1.2.1.10.94.1.1.65546.1.27	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Power. Unit: seconds
NUM hwAdslAtucIntervalSesL	1.3.6.1.2.1.10.94.1.1.65546.1.40	PerfIntervalCount	read-only	For the each interval, adslAtucIntervalSesL reports the number of seconds during which there have been severely errored seconds-line. Unit: seconds
NUM hwAdslAtucIntervalUasL	1.3.6.1.2.1.10.94.1.1.65546.1.41	PerfIntervalCount	read-only	For the each interval, adslAtucIntervalUasL reports the number of seconds during which there have been unavailable seconds-line. Unit: seconds
NUM hwAdslAturChanIntervalCorrectedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.38	PerfIntervalCount	read-only	Count of all blocks received with errors that were corrected on this channel during this interval.
NUM hwadslAturChanIntervalCrcBlks	1.3.6.1.2.1.10.94.1.1.13.1.65538	PerfIntervalCount	read-only	Count of all blocks received with CRC anomalies on this channel during this interval.
NUM hwadslAturChanIntervalFecBlks	1.3.6.1.2.1.10.94.1.1.13.1.65536	PerfIntervalCount	read-only	Count of all blocks received with FRC anomalies on this channel during this interval.
NUM hwadslAturChanIntervalHecBlks	1.3.6.1.2.1.10.94.1.1.13.1.65537	PerfIntervalCount	read-only	Count of all blocks received with HRC anomalies on this channel during this interval.
NUM hwAdslAturChanIntervalReceivedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.36	PerfIntervalCount	read-only	Count of all encoded blocks received on this channel during this interval.
NUM hwAdslAturChanIntervalTransmittedBlks	1.3.6.1.2.1.10.94.1.1.65546.1.37	PerfIntervalCount	read-only	Count of all encoded blocks transmitted on this channel during this interval.
NUM hwAdslAturChanIntervalUncorrectBlks	1.3.6.1.2.1.10.94.1.1.65546.1.39	PerfIntervalCount	read-only	Count of all blocks received with uncorrectable errors on this channel during this interval.
NUM hwAdslAturIntervalESs	1.3.6.1.2.1.10.94.1.1.65546.1.28	PerfIntervalCount	read-only	Count of Errored Seconds in the interval. The errored second parameter is a count of one-second intervals containing one or more crc anomalies, or one or more los or sef defects. Unit: seconds
NUM hwAdslAturIntervalLofs	1.3.6.1.2.1.10.94.1.1.65546.1.29	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Framing. Unit: seconds
NUM hwAdslAturIntervalLoss	1.3.6.1.2.1.10.94.1.1.65546.1.30	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Signal. Unit: seconds
NUM hwAdslAturIntervalLprs	1.3.6.1.2.1.10.94.1.1.65546.1.31	PerfIntervalCount	read-only	Count of seconds in the interval when there was Loss of Power. Unit: seconds
NUM hwAdslAturIntervalSesL	1.3.6.1.2.1.10.94.1.1.65546.1.42	PerfIntervalCount	read-only	For the each interval, adslAturIntervalSesL reports the number of seconds during which there have been severely errored seconds-line. Unit: seconds
NUM hwAdslAturIntervalUasL	1.3.6.1.2.1.10.94.1.1.65546.1.43	PerfIntervalCount	read-only	For the each interval, adslAturIntervalUasL reports the number of seconds during which there have been unavailable seconds-line. Unit: seconds
RowStatus (3)
ROW hwadslLineExtConfProfileRowStatus	1.3.6.1.2.1.10.94.1.1.65543.1.65535	RowStatus	read-create	This object is used to create a new row or modify or delete an existing row in this table. A profile activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service, (by setting this object to 'destroy' or 'outOfService') it must be first unreferenced from all associated lines. If the creator of this MIB has chosen not to implement 'dynamic assignment' of profiles, this object's MIN-ACCESS is read-only and its value is always to be 'active'.
ROW hwAdslLinePvcRowStatus	1.3.6.1.2.1.10.94.1.1.65536.1.11	RowStatus	read-create	Row status. Add or delete a table item.
ROW hwxdslDynamicProfRowStatus	1.3.6.1.2.1.10.94.1.1.65550.1.51	RowStatus	read-create	This object is used to create a new row or to modify or delete an existing row in this table. A profile is activated by setting this object to 'active'. When 'active' is set, the system will validate the profile. Before a profile can be deleted or taken out of service (by setting this object to 'destroy' or 'outOfService'), it must be first unreferenced from all associated templates.
Unsigned32 (38)
U32 hwadsl2TranMissionStardardMask	1.3.6.1.2.1.10.94.1.1.65543.1.20	Unsigned32	read-write	The tranmission stardard mask. The Mask bit and the corresponding Transmission Standard: 0x 1 1 1 1 1 1 ETSI T1.413 G992.5 G992.3 G992.2 G992.1 The Default BitMask: 0X0.
U32 hwadsl2TransMissionAnnexMask	1.3.6.1.2.1.10.94.1.1.65543.1.21	Unsigned32	read-write	The transMission annex Mask. The Mask bit and the corresponding Transmission Annex: 0x 1 1 1 1 1 Annex .J Annex .M Annex .L Annex .B Annex .A The Default BitMask: 0X0.
U32 hwAdslAtucPrevAttainableRate	1.3.6.1.2.1.10.94.1.1.65539.1.3	Unsigned32	read-only	Indicates the maximum attainable data rate by the ATU-C at the time of the last adslAtucRateChangeTrap event. Unit: bps
U32 hwAdslAturPrevAttainableRate	1.3.6.1.2.1.10.94.1.1.65539.1.4	Unsigned32	read-only	Indicates the maximum attainable data rate by the ATU-R at the time of the last adslAtucRateChangeTrap event. Unit: bps
U32 hwxdslDynamicProfCh1MaxDelayDs	1.3.6.1.2.1.10.94.1.1.65550.1.13	Unsigned32	read-create	Maximum Interleave Delay on Downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay is as close as possible to, but less than or equal to, hwxdslDynamicProfCh1MaxDelayDs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Range: 0-200 Unit: milliseconds
U32 hwxdslDynamicProfCh1MaxDelayUs	1.3.6.1.2.1.10.94.1.1.65550.1.14	Unsigned32	read-create	Maximum Interleave Delay on Upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay is as close as possible to, but less than or equal to, hwxdslDynamicProfCh1MaxDelayUs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Range: 0-200 Unit: milliseconds
U32 hwxdslDynamicProfCh2MaxDelayDs	1.3.6.1.2.1.10.94.1.1.65550.1.17	Unsigned32	read-create	Maximum Interleave Delay on Downstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Downstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay is as close as possible to, but less than or equal to, hwxdslDynamicProfCh2MaxDelayDs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Range: 0-200 Unit: milliseconds
U32 hwxdslDynamicProfCh2MaxDelayUs	1.3.6.1.2.1.10.94.1.1.65550.1.18	Unsigned32	read-create	Maximum Interleave Delay on Upstream direction. The maximum one-way interleaving delay introduced by the PMS-TC on Upstream direction. The XTUs shall choose the S (factor) and D (depth) values such that the actual one-way interleaving delay is as close as possible to, but less than or equal to, hwxdslDynamicProfCh2MaxDelayUs. The delay is coded in ms, with the value 0 indicating no delay bound is being imposed. Range: 0-200 Unit: milliseconds
U32 hwxdslDynamicProfDpboEsEL	1.3.6.1.2.1.10.94.1.1.65550.1.25	Unsigned32	read-create	This configuration parameter defines the assumed electrical length of cables (E-side cables) connecting exchange based DSL services to a remote flexibility point (cabinet), that hosts the xTU-C that is subject to spectrally shaped downstream power back-off depending on this length. For this parameter the electrical length is defined as the loss (in dB) of an equivalent length of hypothetical cable at a reference frequency defined by the network operator or in spectrum management regulations. DPBOESEL shall be coded as an unsigned integer representing an electrical length from 0 dB (coded as 0) to 255.5 dB (coded as 511) in steps of 0.5 dB. All values in the range are valid.If DPBOESEL is set to zero, the DPBO in this section shall be disabled. Range: 0-511 Unit: 0.5dB
U32 hwxdslDynamicProfDpboFMax	1.3.6.1.2.1.10.94.1.1.65550.1.29	Unsigned32	read-create	DPBOFMAX defines the maximum frequency at which DPBO may be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 138 kHz (coded as 32) to 29997.75 kHz (coded as 6956). Range: 32-6956 Unit: 4.3125 KHz
U32 hwxdslDynamicProfDpboFMin	1.3.6.1.2.1.10.94.1.1.65550.1.28	Unsigned32	read-create	DPBOFMIN defines the minimum frequency from which the DPBO shall be applied. It shall be coded as a 16 bits unsigned integer representing a frequency in multiple of 4.3125 KHz. The range of valid values is from 0 kHz (coded as 0) to 8832 kHz (coded as 2048). Range: 0-2048 Unit: 4.3125 KHz
U32 hwxdslDynamicProfDpboMus	1.3.6.1.2.1.10.94.1.1.65550.1.27	Unsigned32	read-create	DPBOMUS defines the assumed Minimum Usable receive Signal PSD (in dBm/Hz) for exchange based services, used to modify parameter DPBOFMAX defined below. It shall be coded as an unsigned integer representing a PSD level from 0 dBm/Hz (coded as 0) to -127.5 dBm/Hz (coded as 255) in steps of 0.5 dBm/Hz. All values in the range are valid. Range: 0-255 Unit: 0.5dBm/Hz
U32 hwxdslDynamicProfL0Time	1.3.6.1.2.1.10.94.1.1.65550.1.20	Unsigned32	read-create	This minimum time (in seconds) between an Exit from the L2 state and the next Entry into the L2 state. It ranges from 0 to 255 seconds. Range: 0-255
U32 hwxdslDynamicProfL2Atpr	1.3.6.1.2.1.10.94.1.1.65550.1.22	Unsigned32	read-create	The maximum aggregate transmit power reduction (in dB) that can be performed at transition of L0 to L2 state or through a single Power Trim in the L2 state. It ranges from 0 dB to 31 dB. Range: 0-31 Unit: dB
U32 hwxdslDynamicProfL2Atprt	1.3.6.1.2.1.10.94.1.1.65550.1.23	Unsigned32	read-create	The total maximum aggregate transmit power reduction (in dB) that can be performed in an L2 state. This is the sum of all reductions of L2 Request (i.e., at transition of L0 to L2 state) and Power Trims. Range: 0-31 Unit: dB
U32 hwxdslDynamicProfL2Time	1.3.6.1.2.1.10.94.1.1.65550.1.21	Unsigned32	read-create	This minimum time (in seconds) between an Entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Trims in the L2 State. It ranges from 0 to 255 seconds. Range: 0-255
U32 hwxdslDynamicProfMaxNomAtpDs	1.3.6.1.2.1.10.94.1.1.65550.1.40	Unsigned32	read-create	The maximum nominal aggregate transmit power in the downstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm). Range: 0-255 Unit: 0.1 dBm
U32 hwxdslDynamicProfMaxNomAtpUs	1.3.6.1.2.1.10.94.1.1.65550.1.41	Unsigned32	read-create	The maximum nominal aggregate transmit power in the upstream direction during initialization and Showtime. It ranges from 0 to 255 units of 0.1 dBm (physical values are 0 to 25.5 dBm). Range: 0-255 Unit: 0.1 dBm
U32 hwxdslDynamicProfMaxSnrmDs	1.3.6.1.2.1.10.94.1.1.65550.1.7	Unsigned32	read-create	The maximum Noise Margin the xTU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
U32 hwxdslDynamicProfMaxSnrmUs	1.3.6.1.2.1.10.94.1.1.65550.1.8	Unsigned32	read-create	The maximum Noise Margin the xTU-C receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
U32 hwxdslDynamicProfMinSnrmDs	1.3.6.1.2.1.10.94.1.1.65550.1.9	Unsigned32	read-create	The minimum Noise Margin the xTU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
U32 hwxdslDynamicProfMinSnrmUs	1.3.6.1.2.1.10.94.1.1.65550.1.10	Unsigned32	read-create	The minimum Noise Margin the xTU-C receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
U32 hwxdslDynamicProfTargetSnrmDs	1.3.6.1.2.1.10.94.1.1.65550.1.5	Unsigned32	read-create	The target Noise Margin the xTU-R receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
U32 hwxdslDynamicProfTargetSnrmUs	1.3.6.1.2.1.10.94.1.1.65550.1.6	Unsigned32	read-create	The target Noise Margin the xTU-C receiver shall achieve, relative to the BER requirement for each of the downstream bearer channels, to successfully complete initialization. The target noise margin ranges from 0 to 310 units of 0.1 dB (Physical values are 0 to 31 dB). Range: 0-310 Unit: 0.1 dB
U32 hwxdslDynamicProfUpboKL	1.3.6.1.2.1.10.94.1.1.65550.1.32	Unsigned32	read-create	This parameter defines the electrical loop length expressed in dB at 1MHz, kl0, configured by the CO-MIB. The value shall be coded as an unsigned 16 bit number in the range 0 (coded as 0) to 128 dB (coded as 1280) in steps of 0.1 dB. Range: 0-1280 Unit: 0.1 dB
U32 hwXdslPortLastRetrainReason	1.3.6.1.2.1.10.94.1.1.65538.1.706	Unsigned32	read-only	The last retrain reson of Xdsl Line, coded as bit mask. Only one bit can be set valid, all bits set valid means invalid retrain reason.
U32 hwXdslPortRetrainCnt	1.3.6.1.2.1.10.94.1.1.65538.1.705	Unsigned32	read-only	The retrain counts of Xdsl Line.
U32 hwXdslPortStatePortNumber	1.3.6.1.2.1.10.94.1.1.65542.1.1	Unsigned32	read-only	This Object is Port Number of One Slot.
U32 hwXdslPortUpCnt	1.3.6.1.2.1.10.94.1.1.65538.1.700	Unsigned32	read-only	The up counts of Xdsl port.
U32 hwXdslTotalOfActivatedPorts	1.3.6.1.2.1.10.94.1.1.65542.1.3	Unsigned32	read-only	The total of the activated ports.
U32 hwXdslTotalOfActivatingPorts	1.3.6.1.2.1.10.94.1.1.65542.1.5	Unsigned32	read-only	The total of the activating ports.
U32 hwXdslTotalOfBlockedPorts	1.3.6.1.2.1.10.94.1.1.65542.1.7	Unsigned32	read-only	The total of the blocked ports.
U32 hwXdslTotalOfDeactivatedPorts	1.3.6.1.2.1.10.94.1.1.65542.1.4	Unsigned32	read-only	The total of the deactivated ports.
U32 hwXdslTotalOfFailedPorts	1.3.6.1.2.1.10.94.1.1.65542.1.10	Unsigned32	read-only	The total of the failed ports.
U32 hwXdslTotalOfLocalLoopbackPorts	1.3.6.1.2.1.10.94.1.1.65542.1.8	Unsigned32	read-only	The total of the local testing ports.
U32 hwXdslTotalOfRemoteLoopbackPorts	1.3.6.1.2.1.10.94.1.1.65542.1.9	Unsigned32	read-only	The total of the remote testing ports.
U32 hwXdslTotalOfTestingPorts	1.3.6.1.2.1.10.94.1.1.65542.1.6	Unsigned32	read-only	The total of the Testing ports.
U32 hwXdslTotalOfUnknownPorts	1.3.6.1.2.1.10.94.1.1.65542.1.11	Unsigned32	read-only	The total of the unknown testing ports.
No type (39)
hwAdsl	1.3.6.1.4.1.2011.6.31			This MIB is used for defining Huawei's ADSL management MIB objects.
hwAdsl2SCStateTable	1.3.6.1.2.1.10.94.1.1.65549		not-accessible	The table adsl2SCStatusTable contains status parameters of the ADSL2 sub-carriers. The indexes of this table are ifIndex and hwAdsl2SCStatusDirection.
hwAdsl2SCStatusEntry	1.3.6.1.2.1.10.94.1.1.65549.1		not-accessible	The table adsl2SCStatusTable contains status parameters of the ADSL2 sub-carriers. The indexes of this entry are ifIndex and hwAdsl2SCStatusDirection.
hwAdslGeneralTraps	1.3.6.1.2.1.10.94.1.2.65536.1
hwAdslGeneralTrapsOIDs	1.3.6.1.2.1.10.94.1.2.65536.1.0
hwAdslLineBitAllocationEntry	1.3.6.1.2.1.10.94.1.1.65537.1		not-accessible	The hwAdslLineBitAllocationTable contains the detailed bit-allocation information for the current link. This information can be used to determine whether a given sub-carrier loop has sufficient margin to support ADSL data rates, and possibly to determine whether certain specific types of interfe- rence or line attenuation exist.The bit allocation information are only va- lid when the ATU-C is in the C-ACTIVE state. The index of this entry is ifIndex.
hwAdslLineBitAllocationTable	1.3.6.1.2.1.10.94.1.1.65537		not-accessible	The hwAdslLineBitAllocationTable contains the detailed bit-allocation information for the current link. This information can be used to determine whether a given sub-carrier loop has sufficient margin to support ADSL data rates, and possibly to determine whether certain specific types of interfe- rence or line attenuation exist.The bit allocation information are only va- lid when the ATU-C is in the C-ACTIVE state. The index of this table is ifIndex.
hwadslLineExtConfProfileEntry	1.3.6.1.2.1.10.94.1.1.65543.1		not-accessible	This table contains information on the ADSL extend line configuration. One entry in this table reflects a extend line profile defined by a manager which can be used to configure the ADSL line. The index of this entry is hwadslLineExtConfProfileName.
hwadslLineExtConfProfileTable	1.3.6.1.2.1.10.94.1.1.65543		not-accessible	This table contains information on the ADSL extend line configuration. One entry in this table reflects a extend line profile defined by a manager which can be used to configure the ADSL line. The index of this table is hwadslLineExtConfProfileName.
hwAdslLineLatestActParaEntry	1.3.6.1.2.1.10.94.1.1.65544.1		not-accessible	This table provides one row for each ADSL PORT. Each row contains the latest actived Parameters. The index of this entry is ifIndex.
hwAdslLineLatestActParaTable	1.3.6.1.2.1.10.94.1.1.65544		not-accessible	This table provides one row for each ADSL PORT. Each row contains the latest actived Parameters. The index of this table is ifIndex.
hwAdslLinePreActParaEntry	1.3.6.1.2.1.10.94.1.1.65539.1		not-accessible	This table provides one row for each ADSL PORT. Each row contains the preactived Parameters. The index of this entry is ifIndex.
hwAdslLinePreActParaTable	1.3.6.1.2.1.10.94.1.1.65539		not-accessible	This table provides one row for each ADSL PORT. Each row contains the preactived Parameters. The index of this table is ifIndex.
hwAdslLinePvcEntry	1.3.6.1.2.1.10.94.1.1.65536.1		not-accessible	PVC configuration table of the ADSL port and used to configure the VPI and VCI of the ADSL port. The indexes of this entry are ifIndex,hwAdsllinePvcVpi,and hwAdsllinePvcVci. This table is used to configure only the CO PVC.
hwAdslLinePvcTable	1.3.6.1.2.1.10.94.1.1.65536		not-accessible	PVC configuration table of the ADSL port and used to configure the VPI and VCI of the ADSL port. The indexes of this table are ifIndex,hwAdsllinePvcVpi,and hwAdsllinePvcVci. This table is used to configure only the CO PVC.
NTF hwAdslPortActRateMonitorTrap	1.3.6.1.2.1.10.94.1.2.65536.1.0.1			Definition of the trap reported when the ADSL port rate fails to meet the requirement. If ADSL act rate is lower than threshold, hwTrapType is 1. Otherwise, hwTrapType is 2.
hwAdslPortPerformanceStatEntry	1.3.6.1.2.1.10.94.1.1.65546.1		not-accessible	This table is used to describe the performance statistics of the ADSL port within 15 minutes. The indexes of this entry are ifIndex and hwAdslPort15minutesPerformanceInterval.
hwAdslPortPerformanceStatTable	1.3.6.1.2.1.10.94.1.1.65546		not-accessible	This table is used to describe the performance statistics of the ADSL port within 15 minutes. The indexes of this table are ifIndex and hwAdslPort15minutesPerformanceInterval.
NTF hwAdslPortRateChangeTrap	1.3.6.1.2.1.10.94.1.2.65536.1.0.2			ADSL act rate is change trap. This trap message is generated when the ADSL port rate change.
hwAdslPortRateChangeTrapParaEntry	1.3.6.1.2.1.10.94.1.1.65547.1		not-accessible	ADSL line rate change trap parameter table. The index of this entry is ifIndex.
hwAdslPortRateChangeTrapParaTable	1.3.6.1.2.1.10.94.1.1.65547		not-accessible	ADSL line rate change trap parameter table. The index of this table is ifIndex.
hwAdslTraps	1.3.6.1.2.1.10.94.1.2.65536
hwPortThreePriorityEntry	1.3.6.1.2.1.10.94.1.1.65540.1		not-accessible	Adsl port three priority table. The index of this entry is ifIndex.
hwPortThreePriorityTable	1.3.6.1.2.1.10.94.1.1.65540		not-accessible	Adsl port three priority table. The index of this table is ifIndex.
hwSlotMacMaxNoLimitEntry	1.3.6.1.2.1.10.94.1.1.65541.1		not-accessible	Max mac learning no limit table. The index of this entry is hwFrameIndex and hwSlotIndex.
hwSlotMacMaxNoLimitTable	1.3.6.1.2.1.10.94.1.1.65541		not-accessible	Max mac learning no limit table. The index of this table is hwFrameIndex and hwSlotIndex.
hwXdslDynamicInfoCollectEntry	1.3.6.1.2.1.10.94.1.1.65552.1		not-accessible	The table hwXdslDynamicInfoCollectTable implement xDSL port Dynamic information collect. The index of this entry is hwFrameIndex and hwSlotIndex.
hwXdslDynamicInfoCollectTable	1.3.6.1.2.1.10.94.1.1.65552		not-accessible	The table hwXdslDynamicInfoCollectTable implement xDSL port Dynamic information collect. The index of this table is hwFrameIndex and hwSlotIndex.
hwxdslDynamicProfEntry	1.3.6.1.2.1.10.94.1.1.65550.1		not-accessible	This table includes common parameters of the xdsl Dynamic profile. The index of this entry is hwxdslDynamicProfProfileName.
hwxdslDynamicProfTable	1.3.6.1.2.1.10.94.1.1.65550		not-accessible	This table includes common parameters of the xdsl Dynamic profile. The index of this table is hwxdslDynamicProfProfileName.
hwXdslPortEntry	1.3.6.1.2.1.10.94.1.1.65538.1		not-accessible	This table includes xDSL(e.g. adsl,g.shdsl,vdsl...)port information, Used to support common attributes of the ADSL, G.SHDSL, and VDSL ports. The index of this entry is ifIndex.
hwXdslPortIopCaptureEntry	1.3.6.1.2.1.10.94.1.1.65551.1		not-accessible	The table hwXdslPortIopCaptureTable implement xDSL port IOP information capture. The index of this entry is ifIndex.
hwXdslPortIopCaptureTable	1.3.6.1.2.1.10.94.1.1.65551		not-accessible	The table hwXdslPortIopCaptureTable implement xDSL port IOP information capture. The index of this table is ifIndex.
hwXdslPortPerformanceStatEntry	1.3.6.1.2.1.10.94.1.1.65545.1		not-accessible	XDSL port performance statistic table. The indexes of this entry are ifIndex and hwXdslPort15minutesPerformanceInterval.
hwXdslPortPerformanceStatTable	1.3.6.1.2.1.10.94.1.1.65545		not-accessible	XDSL port performance statistic table. The indexes of this table are ifIndex and hwXdslPort15minutesPerformanceInterval.
hwXdslPortStateStatisticEntry	1.3.6.1.2.1.10.94.1.1.65542.1		not-accessible	XDSL port state statistic table, used to support the statistics information about the status mapping and status of ports on the service boards, such as the ADSL, G.SHDSL and VDSL boards. The indexes of this entry are ifType, hwFrameIndex, and hwSlotIndex.
hwXdslPortStateStatisticTable	1.3.6.1.2.1.10.94.1.1.65542		not-accessible	XDSL port state statistic table, used to support the statistics information about the status mapping and status of ports on the service boards, such as the ADSL, G.SHDSL and VDSL boards. The indexes of this table are ifType, hwFrameIndex, and hwSlotIndex.
hwXdslPortTable	1.3.6.1.2.1.10.94.1.1.65538		not-accessible	This table includes xDSL(e.g. adsl,g.shdsl,vdsl...)port information, Used to support common attributes of the ADSL, G.SHDSL, and VDSL ports. The index of this table is ifIndex.
hwXdslSysManagementParaTable	1.3.6.1.2.1.10.94.1.1.65548

RFC description

Huawei vendor-private extension augmenting standard ADSL line MIB with ADSL performance monitoring, configuration, and alarm trap objects.

Start monitoring Huawei DSLAM / ADSL broadband access equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-ADSL-MIB

This MIB depends on

Related MIBs

What Is HUAWEI-ADSL-MIB?

What Can Be Monitored

Supported Devices

Monitoring Examples

RFC description