HUAWEI-ENERGYMNGT-MIB

MIB Reference — IPNetwork Monitor · Updated October 05, 2026

All MIBs › HUAWEI-ENERGYMNGT-MIB

Organization: Huawei Technologies Co.,Ltd.

Last Updated: 2015-05-30

Category: Technology: Energy Efficiency, Vendor: Huawei

Description: Huawei energy management MIB for monitoring power consumption, configuring energy-saving policies, and tracking power efficiency metrics on Huawei devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-ENERGYMNGT-MIB?

HUAWEI-ENERGYMNGT-MIB is a Huawei enterprise MIB module dedicated to energy management on Huawei networking equipment, part of the vendor's broader energy-efficiency feature set for routers and switches. It exposes configuration objects for energy-saving policies (such as scheduled interface power-down) alongside objects for monitoring power consumption and efficiency metrics. It is explicitly used to monitor the hardware power-related status of a device, letting administrators track real-time power draw and energy-saving policy state to detect abnormal power consumption or a device stuck out of a low-power mode. It sits within Huawei's private enterprise MIB tree without an apparent direct dependency on a specific IETF standard, though it complements standard entity/power MIBs. It is typically deployed in enterprise and carrier networks where operators want to track and reduce the energy footprint of large device fleets. Engineers can download the HUAWEI-ENERGYMNGT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-ENERGYMNGT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

  • Huawei routers
  • Huawei switches

Monitoring Examples

An administrator would poll the energy-management objects to read current power consumption for a device or module and compare it against a baseline, and would check the state of configured energy-saving policies to confirm they are active as scheduled. A sudden rise in reported power consumption without a corresponding policy change could indicate a fan or power-supply issue, or a device failing to enter its expected low-power state. No concrete object names were available in the source data for this MIB, so this describes the typical energy-management monitoring workflow rather than confirmed object names.

What Can Be Monitored

  • real-time power consumption
  • energy-saving policy status
  • power efficiency metrics
  • energy-saving schedule state

This MIB depends on

Related MIBs

Imported Objects

From HUAWEI-MIB

huaweiUtilityOBJECT-IDENTITY

From INET-ADDRESS-MIB

InetAddress
InetAddressType

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE

From SNMPv2-TC

DateAndTime
DisplayString
RowStatus
TruthValue

How to Use in IPNetwork Monitor

Example using hwPowerConsumption OID:

Select a Huawei router or switch (power consumption/energy-saving policy) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hwPowerConsumption into the Find box to locate it in the OID tree, then select it and click OK. It reports nE total power consumption, counted from equipment first used. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.
OIDs

RFC description

Manages energy consumption monitoring, power statistics, and energy-saving modes for Huawei network devices.

Start monitoring Huawei router or switch (power consumption/energy-saving policy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-ENERGYMNGT-MIB