HUAWEI-ENT-VOICE-SIPAG-MIB

All MIBs › HUAWEI-ENT-VOICE-SIPAG-MIB

Organization: Huawei Technologies Co.,Ltd.

Last Updated: 2011-07-01

Category: Domain: VoIP/Telephony, Vendor: Huawei

Description: Huawei enterprise voice SIP agent gateway MIB for managing SIP trunk connections and protocol configuration on Huawei voice gateway platforms.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HUAWEI-ENT-VOICE-SIPAG-MIB?

HUAWEI-ENT-VOICE-SIPAG-MIB is a Huawei-proprietary MIB for Huawei enterprise voice gateway platforms that defines objects for managing the SIP (Session Initiation Protocol) agent/trunk gateway function, covering SIP trunk connections and related protocol configuration. Its data primarily covers configuration of SIP trunk parameters (peer addresses, registration settings, protocol timers) and, implicitly, operational status of SIP trunk registration and call-signaling health. As a voice-signaling MIB it supports monitoring the software status of SIP connectivity: whether a SIP trunk is registered and reachable, and whether signaling errors or registration failures are occurring, which is a key software-health indicator for enterprise VoIP service continuity. It depends on the standard SIP protocol (RFC 3261) for its underlying semantics and typically works together with HUAWEI-ENT-VOICE-COMMON-MIB, which tracks the DSP hardware resources SIP calls ultimately consume. It is deployed on Huawei enterprise voice gateways connecting an on-premises PBX or IP telephony system to a SIP trunk provider or SIP-based carrier network. Engineers can download the HUAWEI-ENT-VOICE-SIPAG-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HUAWEI-ENT-VOICE-SIPAG-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Huawei enterprise voice gateways

Monitoring Examples

An administrator would poll SIP trunk registration-status objects to confirm a configured trunk remains registered with its SIP provider, and would check protocol-configuration objects to verify signaling parameters like proxy address or transport type are correctly applied. No sample object names were provided for this module, so specific table names cannot be cited, but the module description confirms SIP management is the scope of this MIB. A SIP trunk repeatedly failing registration would point to a network reachability or credential problem between the gateway and the SIP provider.

What Can Be Monitored

SIP trunk registration status
SIP trunk configuration parameters
signaling/registration failure counts

Imported Objects

From HUAWEI-MIB

hwDatacomm

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32
private

From SNMPv2-TC

DisplayString
RowStatus
TEXTUAL-CONVENTION

OIDs

OID symbolic	OID numeric	Type	Access	Description
hwEntVoiceSipagMIB	1.3.6.1.4.1.2011.5.25.250			This mib is used for defining huawei's SIP MIB objects, which provides SIP management.
hwEntSipAgConfigTable	1.3.6.1.4.1.2011.5.25.250.1		not-accessible	This table is used to config the parameters of SipAg. The index of this table is hwEntSipAgId.
hwEntSipAgConfigEntry	1.3.6.1.4.1.2011.5.25.250.1.1		not-accessible	This table is used to config the parameters of SipAg. The index of this entry is hwEntSipAgId.
I32 hwEntSipAgId	1.3.6.1.4.1.2011.5.25.250.1.1.1	Integer32	not-accessible	Sipag ID.
IP hwEntSipAgMediaIPAddress	1.3.6.1.4.1.2011.5.25.250.1.1.2	IpAddress	read-create	Indicates the media IP address.
IP hwEntSipAgSignallingIPAddress	1.3.6.1.4.1.2011.5.25.250.1.1.3	IpAddress	read-create	Indicates the signalling IP address.
I32 hwEntSipAgSignallingPort	1.3.6.1.4.1.2011.5.25.250.1.1.4	Integer32	read-create	Indicates the signalling port.
STR hwEntSipAgMediaAddrName	1.3.6.1.4.1.2011.5.25.250.1.1.5	DisplayString	read-create	Indicates the dynamic media IP name.
STR hwEntSipAgSignallingAddrName	1.3.6.1.4.1.2011.5.25.250.1.1.6	DisplayString	read-create	Indicates the dynamic signalliing IP name.
INT hwEntSipAgTransMode	1.3.6.1.4.1.2011.5.25.250.1.1.7	INTEGER	read-create	Indicates the transfer mode. Options: tcp(1) -TCP udp(2) -UDP sctp(3) -SCTP Default: udp(2)
STR hwEntSipAgDomainName	1.3.6.1.4.1.2011.5.25.250.1.1.8	DisplayString	read-create	Indicates the domain name of sipag.
STR hwEntSipAgHomeDomainName	1.3.6.1.4.1.2011.5.25.250.1.1.9	DisplayString	read-create	Indicates the home domain name.
STR hwEntSipAgRegisterUri	1.3.6.1.4.1.2011.5.25.250.1.1.10	DisplayString	read-create	Indicates the Register-URI.
STR hwEntSipAgConferenceFactoryUri	1.3.6.1.4.1.2011.5.25.250.1.1.11	DisplayString	read-create	Indicates the ConferenceFactory-URI.
STR hwEntSipAgDesc	1.3.6.1.4.1.2011.5.25.250.1.1.12	DisplayString	read-create	Indicates the Description.
STR hwEntSipAgPhoneContext	1.3.6.1.4.1.2011.5.25.250.1.1.13	DisplayString	read-create	Indicates the Phone Context.
ROW hwEntSipAgRowStatus	1.3.6.1.4.1.2011.5.25.250.1.1.14	RowStatus	read-create	This is used to create new rows in this table, modify existing rows, and delete existing rows.
INT hwEntSipAgAdminStatus	1.3.6.1.4.1.2011.5.25.250.1.1.15	INTEGER	read-create	Indicates the AdminStatus. Options: reset(1) -reset switchover(2) -switchover
I32 hwEntSipAgSwitchoverDestination	1.3.6.1.4.1.2011.5.25.250.1.1.16	Integer32	read-create	Indicates the target proxy of switchover. Options: 0: primary proxy 1: secondary proxy
I32 hwEntSipAgProfileIndex	1.3.6.1.4.1.2011.5.25.250.1.1.17	Integer32	read-create	Indicates the ProfileIndex. Default: 1
STR hwEntSipAgProfileName	1.3.6.1.4.1.2011.5.25.250.1.1.18	DisplayString	read-only	Indicates the ProfileName.
I32 hwEntSipAgSrvLogicIndex	1.3.6.1.4.1.2011.5.25.250.1.1.19	Integer32	read-create	Indicates the servelogic index. Default: 0
STR hwEntSipAgSrvLogicName	1.3.6.1.4.1.2011.5.25.250.1.1.20	DisplayString	read-only	Indicates the servelogic name.
INT hwEntSipAgServerDhcpOption	1.3.6.1.4.1.2011.5.25.250.1.1.21	INTEGER	read-create	Indicates the DHCP option. Options: none(1) -none option120(2) -option120 option21(3) -option21 Default: none(1)
INT hwEntSipAgAuthMode	1.3.6.1.4.1.2011.5.25.250.1.1.22	INTEGER	read-create	Indicates the user authentication mode. Options: interface(1) -interface user(2) -single user Default: user(2)
STR hwEntSipAgAuthUserName	1.3.6.1.4.1.2011.5.25.250.1.1.23	DisplayString	read-create	Indicates the auth username.
INT hwEntSipAgAuthPasswordMode	1.3.6.1.4.1.2011.5.25.250.1.1.24	INTEGER	read-create	Indicates the auth password mode. Options: password(1) -auth by password ha1(2) -auth by ha1 Default: password(1)
STR hwEntSipAgAuthPassword	1.3.6.1.4.1.2011.5.25.250.1.1.25	DisplayString	read-create	Indicates the auth password.
STR hwEntSipAgAuthHA1	1.3.6.1.4.1.2011.5.25.250.1.1.26	DisplayString	read-create	Indicates the auth ha1 password.
INT hwEntSipAgSubUAProfile	1.3.6.1.4.1.2011.5.25.250.1.1.27	INTEGER	read-create	Indicates the flag to subscribe to UA-Profile. Options: enable(1) disable(2) Default: enable(1)
INT hwEntSipAgSubRegState	1.3.6.1.4.1.2011.5.25.250.1.1.28	INTEGER	read-create	Indicates the flag to subscribe to REG-STATE. Options: enable(1) disable(2) Default: disable(2)
INT hwEntSipAgSubMwi	1.3.6.1.4.1.2011.5.25.250.1.1.29	INTEGER	read-create	Indicates the flag to subscribe to MWI. Options: enable(1) disable(2) Default: disable(2)
INT hwEntSipAgSdpNegoMode	1.3.6.1.4.1.2011.5.25.250.1.1.30	INTEGER	read-create	Indicates the SDP negotiation mode. Options: local(1) -Local end takes priority when codec negotiation remote(2) -Remote end takes priority when codec negotiation Default: remote(2)
INT hwEntSipAgProxyDualHome	1.3.6.1.4.1.2011.5.25.250.1.1.31	INTEGER	read-create	Indicates the mode of supporting proxy dual-homing. Options: no(1) -not support proxy dual-homing dualhome(2) -support proxy dual-homing, but not support auto switchover autoswitchover(3) -support proxy dual-homing and auto switchover Default: dualhome(2)
INT hwEntSipAgProxyDetectMode	1.3.6.1.4.1.2011.5.25.250.1.1.32	INTEGER	read-create	Indicate the proxy detection mode. Options: option(1) -detect proxy by option message probe(2) -detect proxy by probe mode register(3) -detect proxy by register message Default: probe(2)
INT hwEntSipAgProxyRefreshMode	1.3.6.1.4.1.2011.5.25.250.1.1.33	INTEGER	read-create	Indicate Proxy address refresh mode. Options: immediate(1) -immediate switch defer(2) -switch in no calls cases no-switch(3) -no switch null(255) -invalid value
hwEntSipAgRunningTable	1.3.6.1.4.1.2011.5.25.250.2		not-accessible	This table is used to query the running parameters. The index of this table is hwEntSipAgId.
hwEntSipAgRunningEntry	1.3.6.1.4.1.2011.5.25.250.2.1		not-accessible	This table is used to query the running parameters. The index of this entry is hwEntSipAgId.
I32 hwEntSipAgRunningId	1.3.6.1.4.1.2011.5.25.250.2.1.1	Integer32	not-accessible	Sipag ID.
IP hwEntSipAgRunningMediaIPAddress	1.3.6.1.4.1.2011.5.25.250.2.1.2	IpAddress	read-only	Indicates the media ip address.
IP hwEntSipAgRunningSignallingIPAddress	1.3.6.1.4.1.2011.5.25.250.2.1.3	IpAddress	read-only	Indicates the signalling ip address.
I32 hwEntSipAgRunningSignallingPort	1.3.6.1.4.1.2011.5.25.250.2.1.4	Integer32	read-only	Indicates the Signalling Port.
STR hwEntSipAgRunningMediaAddrName	1.3.6.1.4.1.2011.5.25.250.2.1.5	DisplayString	read-only	Indicates the current dynamic media IP name.
STR hwEntSipAgRunningSignallingAddrName	1.3.6.1.4.1.2011.5.25.250.2.1.6	DisplayString	read-only	Indicates the current dynamic signalling IP name.
INT hwEntSipAgRunningTransMode	1.3.6.1.4.1.2011.5.25.250.2.1.7	INTEGER	read-only	Indicates the Transfer Mode. null(255) means the interface is not started. Options: tcp(1) -TCP udp(2) -UDP sctp(3) -SCTP null(255) -interface is not started
STR hwEntSipAgRunningDomainName	1.3.6.1.4.1.2011.5.25.250.2.1.8	DisplayString	read-only	Indicates the domain name of sipag.
STR hwEntSipAgRunningHomeDomainName	1.3.6.1.4.1.2011.5.25.250.2.1.9	DisplayString	read-only	Indicates the home domain name.
STR hwEntSipAgRunningRegisterUri	1.3.6.1.4.1.2011.5.25.250.2.1.10	DisplayString	read-only	Indicates the register-URI.
STR hwEntSipAgRunningConferenceFactoryUri	1.3.6.1.4.1.2011.5.25.250.2.1.11	DisplayString	read-only	Indicates the conferencefactory-URI.
STR hwEntSipAgRunningDesc	1.3.6.1.4.1.2011.5.25.250.2.1.12	DisplayString	read-only	Indicates the description of sipag.
STR hwEntSipAgRunningPhoneContext	1.3.6.1.4.1.2011.5.25.250.2.1.13	DisplayString	read-only	Indicates the phone context.
I32 hwEntSipAgRunningProfileIndex	1.3.6.1.4.1.2011.5.25.250.2.1.14	Integer32	read-only	Indicates the profile index.
STR hwEntSipAgRunningProfileName	1.3.6.1.4.1.2011.5.25.250.2.1.15	DisplayString	read-only	Indicates the ProfileName.
I32 hwEntSipAgRunningSrvLogicIndex	1.3.6.1.4.1.2011.5.25.250.2.1.16	Integer32	read-only	Indicates the servelogic index.
STR hwEntSipAgRunningSrvLogicName	1.3.6.1.4.1.2011.5.25.250.2.1.17	DisplayString	read-only	Indicates the servelogic name.
INT hwEntSipAgRunningServerDhcpOption	1.3.6.1.4.1.2011.5.25.250.2.1.18	INTEGER	read-only	Indicates the DHCP option. Options: none(1) -none option120(2) -option120 option21(3) -option21
INT hwEntSipAgRunningAuthMode	1.3.6.1.4.1.2011.5.25.250.2.1.19	INTEGER	read-only	Indicates user authentication mode. Options: interface(1) -interface user(2) -single user
STR hwEntSipAgRunningAuthUserName	1.3.6.1.4.1.2011.5.25.250.2.1.20	DisplayString	read-only	Indicates the auth username.
INT hwEntSipAgRunningAuthPasswordMode	1.3.6.1.4.1.2011.5.25.250.2.1.21	INTEGER	read-only	Indicates the auth password mode. Options: password(1) -password ha1(2) -HA1
STR hwEntSipAgRunningAuthPassword	1.3.6.1.4.1.2011.5.25.250.2.1.22	DisplayString	read-only	Indicates the auth password.
STR hwEntSipAgRunningAuthHA1	1.3.6.1.4.1.2011.5.25.250.2.1.23	DisplayString	read-only	Indicates the auth ha1 password.
INT hwEntSipAgRunningSubUAProfile	1.3.6.1.4.1.2011.5.25.250.2.1.24	INTEGER	read-only	Indicates the flag to subscribe to UA-Profile. Options: enable(1) disable(2)
INT hwEntSipAgRunningSubRegState	1.3.6.1.4.1.2011.5.25.250.2.1.25	INTEGER	read-only	Indicates the flag to subscribe to REG-STATE. Options: enable(1) disable(2)
INT hwEntSipAgRunningSubMwi	1.3.6.1.4.1.2011.5.25.250.2.1.26	INTEGER	read-only	Indicates the flag to subscribe to MWI. Options: enable(1) disable(2)
INT hwEntSipAgRunningSdpNegoMode	1.3.6.1.4.1.2011.5.25.250.2.1.27	INTEGER	read-only	Indicates the SDP negotiation mode. Options: local(1) -local first remote(2) -remote first
INT hwEntSipAgRunningProxyDualHome	1.3.6.1.4.1.2011.5.25.250.2.1.28	INTEGER	read-only	Indicate the mode of supporting proxy dual-homing. Options: no(1) -not support proxy dual-homing dualhome(2) -support proxy dual-homing, but not support auto switchover autoswitchover(3) -support proxy dual-homing and auto switchover
INT hwEntSipAgRunningProxyDetectMode	1.3.6.1.4.1.2011.5.25.250.2.1.29	INTEGER	read-only	Indicates the proxy detection mode. Options: option(1) -detection proxy by option message probe(2) -detection proxy by probe mode register(3) -detection proxy by register message
INT hwEntSipAgRunningProxyRefreshMode	1.3.6.1.4.1.2011.5.25.250.2.1.30	INTEGER	read-only	Indicate Proxy address refresh mode. Options: immediate(1) -immediate switch defer(2) -switch in no calls cases no-switch(3) -no switch
INT hwEntSipAgRunningState	1.3.6.1.4.1.2011.5.25.250.2.1.31	INTEGER	read-only	Indicate the sipag state. Options: notStart(1) fault(2) normal(3)
hwEntSipAgProxyTable	1.3.6.1.4.1.2011.5.25.250.3		not-accessible	This table is used to config the parameters of sipag proxy. The indexes of this table are hwEntSipAgId, hwSipAgProxyIndex.
hwEntSipAgProxyEntry	1.3.6.1.4.1.2011.5.25.250.3.1		not-accessible	This table is used to config the parameters of sipag proxy. The indexes of this entry are hwEntSipAgId, hwSipAgProxyIndex.
I32 hwEntSipAgProxyId	1.3.6.1.4.1.2011.5.25.250.3.1.1	Integer32	not-accessible	Sipag ID.
I32 hwSipAgProxyIndex	1.3.6.1.4.1.2011.5.25.250.3.1.2	Integer32	not-accessible	proxy index. 0: main 1: standby
IP hwSipAgProxyIPAddress1	1.3.6.1.4.1.2011.5.25.250.3.1.3	IpAddress	read-write	Indicates the proxy IP address1.
IP hwSipAgProxyIPAddress2	1.3.6.1.4.1.2011.5.25.250.3.1.4	IpAddress	read-write	Indicates the proxy IP address2.
I32 hwSipAgProxyPort	1.3.6.1.4.1.2011.5.25.250.3.1.5	Integer32	read-write	Indicates the proxy port.
STR hwSipAgProxyDomainName	1.3.6.1.4.1.2011.5.25.250.3.1.6	DisplayString	read-write	Indicates the proxy domain name.
INT hwSipAgProxyAddressMode	1.3.6.1.4.1.2011.5.25.250.3.1.7	INTEGER	read-write	The proxy address mode. ip(1) dnsA(2) dnsSrv(3) dnsNaptr(4)
hwEntSipAgProxyRunningTable	1.3.6.1.4.1.2011.5.25.250.4		not-accessible	This table is used to query the running parameters of sipag proxy. The indexes of this table are hwEntSipAgId, hwSipAgProxyIndex.
hwEntSipAgProxyRunningEntry	1.3.6.1.4.1.2011.5.25.250.4.1		not-accessible	This table is used to query the running parameters sipag proxy. The indexes of this entry are hwEntSipAgId, hwSipAgProxyIndex.
I32 hwEntSipAgProxyRunningId	1.3.6.1.4.1.2011.5.25.250.4.1.1	Integer32	not-accessible	Sipag ID.
I32 hwSipAgProxyRunningIndex	1.3.6.1.4.1.2011.5.25.250.4.1.2	Integer32	not-accessible	proxy index. 0: main 1: standby
IP hwSipAgProxyRunningIPAddress1	1.3.6.1.4.1.2011.5.25.250.4.1.3	IpAddress	read-only	Indicates the proxy IP address1.
IP hwSipAgProxyRunningIPAddress2	1.3.6.1.4.1.2011.5.25.250.4.1.4	IpAddress	read-only	Indicates the proxy IP address2.
I32 hwSipAgProxyRunningPort	1.3.6.1.4.1.2011.5.25.250.4.1.5	Integer32	read-only	Indicates the Proxy Port.
STR hwSipAgProxyRunningDomainName	1.3.6.1.4.1.2011.5.25.250.4.1.6	DisplayString	read-only	Indicates the proxy domain name.
INT hwSipAgProxyRunningAddressMode	1.3.6.1.4.1.2011.5.25.250.4.1.7	INTEGER	read-only	The proxy address mode. ip(1) dnsA(2) dnsSrv(3) dnsNaptr(4)
INT hwSipAgProxyRunningState	1.3.6.1.4.1.2011.5.25.250.4.1.8	INTEGER	read-only	The proxy state. unknown(1) down(2) up(3)
hwEntSipProfileTable	1.3.6.1.4.1.2011.5.25.250.5		not-accessible	This table is used to query the sipag profile. The index of this table is hwEntSipProfileIndex.
hwEntSipProfileEntry	1.3.6.1.4.1.2011.5.25.250.5.1		not-accessible	This table is used to config the Sip Profile. The index of this entry is hwEntSipProfileIndex.
I32 hwEntSipProfileIndex	1.3.6.1.4.1.2011.5.25.250.5.1.1	Integer32	not-accessible	Indicates the index of sipprofile.
STR hwEntSipProfileName	1.3.6.1.4.1.2011.5.25.250.5.1.2	DisplayString	read-only	Indicates the name of sipprofile.
hwEntSipSrvLogicTable	1.3.6.1.4.1.2011.5.25.250.6		not-accessible	This table is used to config the Sip Serve-Logic list. The index of this table is hwEntSipSrvLogicIndex.
hwEntSipSrvLogicEntry	1.3.6.1.4.1.2011.5.25.250.6.1		not-accessible	This table is used to config the sip serve-logic list. The index of this entry is hwEntSipSrvLogicIndex.
I32 hwEntSipSrvLogicIndex	1.3.6.1.4.1.2011.5.25.250.6.1.1	Integer32	not-accessible	Indicates the index of serve-logic.
STR hwEntSipSrvLogicName	1.3.6.1.4.1.2011.5.25.250.6.1.2	DisplayString	read-only	Indicates the name of serve-logic.
hwEntSipAgDmmParaTable	1.3.6.1.4.1.2011.5.25.250.7		not-accessible	This table is used to config the digitmap. The index of this table is hwEntSipAgId.
hwEntSipAgDmmParaEntry	1.3.6.1.4.1.2011.5.25.250.7.1		not-accessible	This table is used to config the digitmap. The index of this entry is hwEntSipAgId.
I32 hwEntSipAgDmmParaId	1.3.6.1.4.1.2011.5.25.250.7.1.1	Integer32	not-accessible	Sipag ID.
I32 hwEntSipAgDmmParaStartTimer	1.3.6.1.4.1.2011.5.25.250.7.1.2	Integer32	read-write	Indicates the length of the DMM start timer. Default: 20 Unit: second
I32 hwEntSipAgDmmParaShortTimer	1.3.6.1.4.1.2011.5.25.250.7.1.3	Integer32	read-write	Indicates the length of the DMM short timer. Default: 4 Unit: second
I32 hwEntSipAgDmmParaLongTimer	1.3.6.1.4.1.2011.5.25.250.7.1.4	Integer32	read-write	Indicates the length of the DMM long timer. Default: 20 Unit: second
hwEntSipAgUserGroupTable	1.3.6.1.4.1.2011.5.25.250.8		not-accessible	This table is used to config the parameters of sip user group. The index of this table is hwEntSipAgUserGroupName.
hwEntSipAgUserGroupEntry	1.3.6.1.4.1.2011.5.25.250.8.1		not-accessible	This table is used to config the parameters of sip user group. The index of this entry is hwEntSipAgUserGroupName.
I32 hwEntSipAgUserGroupSipAgId	1.3.6.1.4.1.2011.5.25.250.8.1.1	Integer32	not-accessible	Sipag ID.
I32 hwEntSipAgUserGroupId	1.3.6.1.4.1.2011.5.25.250.8.1.2	Integer32	not-accessible	User Group ID.
INT hwEntSipAgUserGroupRegisterUriMode	1.3.6.1.4.1.2011.5.25.250.8.1.3	INTEGER	read-create	Indicates the user group register URI mode. Options: inneruser(1) -inner user alone(2) -alone
STR hwEntSipAgUserGroupUri	1.3.6.1.4.1.2011.5.25.250.8.1.4	DisplayString	read-create	Indicates the Register-URI of the sip user group without the domain.
STR hwEntSipAgUserGroupGrpName	1.3.6.1.4.1.2011.5.25.250.8.1.5	DisplayString	read-create	Indicates the sip user group Name.
STR hwEntSipAgUserGroupAuthUserName	1.3.6.1.4.1.2011.5.25.250.8.1.6	DisplayString	read-create	Indicates the Auth Username of the sip user group.
INT hwEntSipAgUserGroupAuthPassWordMode	1.3.6.1.4.1.2011.5.25.250.8.1.7	INTEGER	read-create	Indicates the Auth PasswordMode of the sip user group. Options: password(1) -auth by password ha1(2) -auth by HA1 Default: password(1)
STR hwEntSipAgUserGroupAuthPassword	1.3.6.1.4.1.2011.5.25.250.8.1.8	DisplayString	read-create	Indicates the Auth Password of the sip user group.
STR hwEntSipAgUserGroupAuthHA1	1.3.6.1.4.1.2011.5.25.250.8.1.9	DisplayString	read-create	Indicates the Auth HA1 value of the sip user group.
INT hwEntSipAgUserGroupPrecinctMode	1.3.6.1.4.1.2011.5.25.250.8.1.10	INTEGER	read-create	Indicates the user PrecinctMode in the sip user group. Options: local(1) remote(2) Default: local(1)
INT hwEntSipAgUserGroupSubUaProfile	1.3.6.1.4.1.2011.5.25.250.8.1.11	INTEGER	read-create	Indicates the flag of the user group with the same UA Profile privilege. Options: enable(1) disable(2) Default: enable(1)
ROW hwEntSipAgUserGroupRowStatus	1.3.6.1.4.1.2011.5.25.250.8.1.12	RowStatus	read-create	This is used to create new rows in this table, modify existing rows, and to delete existing rows.
INT hwEntSipAgUserGroupAdminStatus	1.3.6.1.4.1.2011.5.25.250.8.1.13	INTEGER	read-create	Indicates the admin operation of the sip user group. Options: startservice(1) -start service endservice(2) -end service
INT hwEntSipAgUserGroupRunningState	1.3.6.1.4.1.2011.5.25.250.8.1.14	INTEGER	read-only	Indicates the service state of user group. Options: startSvc(1) -start service rBlock(2) -remote block lBlock(3) -local block
hwEntSipAgSoftNumberParaTable	1.3.6.1.4.1.2011.5.25.250.9		not-accessible	This table is used to config the soft number parameters of sipag. The indexes of this table are hwEntSipAgId, hwEntSipAgSoftNumberParaNo.
hwEntSipAgSoftNumberParaEntry	1.3.6.1.4.1.2011.5.25.250.9.1		not-accessible	This table is used to config the soft number parameters of sipag. The indexes of this entry are hwEntSipAgId, hwEntSipAgSoftNumberParaNo.
I32 hwEntSipAgSoftNumberParaId	1.3.6.1.4.1.2011.5.25.250.9.1.1	Integer32	not-accessible	Sipag ID.
I32 hwEntSipAgSoftNumberParaNo	1.3.6.1.4.1.2011.5.25.250.9.1.2	Integer32	not-accessible	The number of sip mg soft number parameter.
I32 hwEntSipAgSoftNumberParaValue	1.3.6.1.4.1.2011.5.25.250.9.1.3	Integer32	read-write	The value of sip mg soft number parameter.
hwEntSipAgSoftStringParaTable	1.3.6.1.4.1.2011.5.25.250.10		not-accessible	This table is used to config the soft string Parameters of SIP interface. The indexes of this table are hwEntSipAgId, hwEntSipAgSoftStringParaNo.
hwEntSipAgSoftStringParaEntry	1.3.6.1.4.1.2011.5.25.250.10.1		not-accessible	This table is used to config the soft string parameters of sipag. The indexes of this entry are hwEntSipAgId, hwEntSipAgSoftStringParaNo.
I32 hwEntSipAgSoftStringParaId	1.3.6.1.4.1.2011.5.25.250.10.1.1	Integer32	not-accessible	Sipag ID.
I32 hwEntSipAgSoftStringParaNo	1.3.6.1.4.1.2011.5.25.250.10.1.2	Integer32	not-accessible	The number of sip mg soft string parameter.
STR hwEntSipAgSoftStringParaValue	1.3.6.1.4.1.2011.5.25.250.10.1.3	DisplayString	read-write	The value of sip mg soft string parameter.
hwEntSipAgSoftStringParaRunningTable	1.3.6.1.4.1.2011.5.25.250.11		not-accessible	This table is used to query the running soft string parameters of sipag. The indexes of this table are hwEntSipAgId, hwEntSipAgSoftStringParaNo.
hwEntSipAgSoftStringParaRunningEntry	1.3.6.1.4.1.2011.5.25.250.11.1		not-accessible	This table is used to query the running soft string parameters of sipag. The indexes of this entry are hwEntSipAgId, hwEntSipAgSoftStringParaNo.
I32 hwEntSipAgSoftStringParaRunningId	1.3.6.1.4.1.2011.5.25.250.11.1.1	Integer32	not-accessible	Sipag ID.
I32 hwEntSipAgSoftStringParaRunningNo	1.3.6.1.4.1.2011.5.25.250.11.1.2	Integer32	not-accessible	The number of sip mg soft string parameter.
STR hwEntSipAgSoftStringParaRunningValue	1.3.6.1.4.1.2011.5.25.250.11.1.3	DisplayString	read-only	The value of sip mg soft string parameter.
hwEntFaxModemParaTable	1.3.6.1.4.1.2011.5.25.250.12		not-accessible	This table is used to config the fax and modem parameters of sipag. The index of this table is hwEntSipAgId.
hwEntFaxModemParaEntry	1.3.6.1.4.1.2011.5.25.250.12.1		not-accessible	This table is used to config the fax parameter. The index of this entry is hwEntSipAgId.
I32 hwEntFaxSipAgId	1.3.6.1.4.1.2011.5.25.250.12.1.1	Integer32	not-accessible	Sipag ID.
INT hwEntFaxTransMode	1.3.6.1.4.1.2011.5.25.250.12.1.2	INTEGER	read-write	Indicates the fax transmission mode. Options: thoroughly(1) -use voice codec t38(2) -use T.38 codec Default: thoroughly(1)
INT hwEntModemTransMode	1.3.6.1.4.1.2011.5.25.250.12.1.3	INTEGER	read-write	Indicates the modem transmission mode. Options: thoroughly(1) -Thoroughly transmission relay(2) -Relay mode Default: thoroughly(1)
INT hwEntFaxModemNegoMode	1.3.6.1.4.1.2011.5.25.250.12.1.4	INTEGER	read-write	Indicates the negotiate mode. Options: negotiate(1) -negotiate selfswitch(2) -do not negotiate Default: negotiate(1)
INT hwEntFaxModemParaVbdCodec	1.3.6.1.4.1.2011.5.25.250.12.1.5	INTEGER	read-write	Indicates the codec of VBD. Options: g711a(1) -G.711A g711u(2) -G.711U Default: g711a(1)
INT hwEntFaxModemParaVbdPtType	1.3.6.1.4.1.2011.5.25.250.12.1.6	INTEGER	read-write	Indicates the payload type of VBD. Options: static(1) -static payload type dynamic(2) -dynamic payload type Default: static(1)
INT hwEntFaxModemVbdAttributeType	1.3.6.1.4.1.2011.5.25.250.12.1.7	INTEGER	read-write	Indicate the format of session attribute lines when starting fax VBD negotiation. Options: v152(1) -v.152 format chinatelecom(2) -chinatelecom format chinatelecomext(3) -chinatelecom ext format ietf(4) -ietf format Default: v152(1)
INT hwEntFaxModemRtpInterval	1.3.6.1.4.1.2011.5.25.250.12.1.8	INTEGER	read-write	Indicates the default RTP packet time of DSP channel. Options: pt5ms(1) pt10ms(2) pt20ms(3) pt30ms(4) Default: pt10ms(2)
hwEntDtmfParaTable	1.3.6.1.4.1.2011.5.25.250.13		not-accessible	This table is used to config the DTMF parameter of sipag. The index of this table is hwEntSipAgId.
hwEntDtmfParaEntry	1.3.6.1.4.1.2011.5.25.250.13.1		not-accessible	This table is used to config the DTMF parameter of sipag. The index of this entry is hwEntSipAgId.
I32 hwEntDtmfSipAgId	1.3.6.1.4.1.2011.5.25.250.13.1.1	Integer32	not-accessible	Sipag ID.
INT hwEntDtmfTransMode	1.3.6.1.4.1.2011.5.25.250.13.1.2	INTEGER	read-write	Indicates the transmission mode of DTMF. Options: thoroughly(1) -transparent transmission erase(2) -erase DTMF Default: thoroughly(1)
hwEntNteTable	1.3.6.1.4.1.2011.5.25.250.14		not-accessible	This table is used to config the nte parameter of sipag. The index of this table is hwEntSipAgId.
hwEntNteEntry	1.3.6.1.4.1.2011.5.25.250.14.1		not-accessible	This table is used to config the nte parameter of sipag. The index of this entry is hwEntSipAgId..
I32 hwEntNteSipAgId	1.3.6.1.4.1.2011.5.25.250.14.1.1	Integer32	not-accessible	Sipag ID.
INT hwEntNteNegoMode	1.3.6.1.4.1.2011.5.25.250.14.1.2	INTEGER	read-write	Indicates the start mode of NTE. Options: negoStart(1) -negotiate start fixedStart(2) -fixed start noInitiativeStart(3) -no initiative start Default: noInitiativeStart(3)
INT hwEntNteFaxModem	1.3.6.1.4.1.2011.5.25.250.14.1.3	INTEGER	read-write	Indicates the flag of fax and modem event using nte parameter. Options: enable(1) disable(2) Default: enable(1)
INT hwEntNteFlashHook	1.3.6.1.4.1.2011.5.25.250.14.1.4	INTEGER	read-write	Indicates the enabled flag of flash hook event using nte parameter. Options: enable(1) disable(2) Default: disable(2)
INT hwEntNteDtmf	1.3.6.1.4.1.2011.5.25.250.14.1.5	INTEGER	read-write	Indicates the enabled flag of dtmf using nte parameter. Options: enable(1) disable(2) Default: enable(1)
hwEntRedundancyTable	1.3.6.1.4.1.2011.5.25.250.15		not-accessible	This table is used to config the redundancy parameter. The index of this table is hwEntSipAgId.
hwEntRedundancyEntry	1.3.6.1.4.1.2011.5.25.250.15.1		not-accessible	This table is used to config the redundancy parameter of sipag. The index of this entry is hwEntSipAgId.
I32 hwEntRedundancySipAgId	1.3.6.1.4.1.2011.5.25.250.15.1.1	Integer32	not-accessible	Sipag ID.
INT hwEntRedundancyNegoMode	1.3.6.1.4.1.2011.5.25.250.15.1.2	INTEGER	read-write	Indicates the start mode of the redundancy. Options: negoStart(1) -negotiate start fixedStart(2) -fixed start noInitiativeStart(3) -no initiative start Default: noInitiativeStart(3)
INT hwEntRedundancyStartMode	1.3.6.1.4.1.2011.5.25.250.15.1.3	INTEGER	read-write	Indicates the start mode of the redundancy. Options: smartRedundancy(1) -smart start redundancy ordinaryRedundancy(2) -start redundancy ordinary Default: ordinaryRedundancy(2)
INT hwEntRedundancyNte	1.3.6.1.4.1.2011.5.25.250.15.1.4	INTEGER	read-write	Indicates the enabled flag of NTE with using redundancy. Options: enable(1) disable(2) Default: disable(2)
INT hwEntRedundancyVbd	1.3.6.1.4.1.2011.5.25.250.15.1.5	INTEGER	read-write	Indicates the enabled flag of the VBD using redundancy. Options: enable(1) disable(2) Default: enable(1)
INT hwEntRedundancyVoice	1.3.6.1.4.1.2011.5.25.250.15.1.6	INTEGER	read-write	Indicates the enabled flag of voice using redundancy. Options: 1. enable(1) 2. disable(2) Default: disable(2)
hwEntVoiceSipagConformance	1.3.6.1.4.1.2011.5.25.250.16
hwEntVoiceSipagCompliances	1.3.6.1.4.1.2011.5.25.250.16.1
hwEntVoiceSipagCompliance	1.3.6.1.4.1.2011.5.25.250.16.1.1			The compliance statement for systems supporting the this module.
hwEntVoiceSipagGroups	1.3.6.1.4.1.2011.5.25.250.16.2
hwEntSipAgConfigGroup	1.3.6.1.4.1.2011.5.25.250.16.2.1			The hwEntSipAgConfig group.
hwEntSipAgRunningGroup	1.3.6.1.4.1.2011.5.25.250.16.2.2			The hwEntSipAgRunning group.
hwEntSipAgProxyGroup	1.3.6.1.4.1.2011.5.25.250.16.2.3			The hwEntSipAgProxy group.
hwEntSipAgProxyRunningGroup	1.3.6.1.4.1.2011.5.25.250.16.2.4			The hwEntSipAgProxyRunning group.
hwEntSipProfileGroup	1.3.6.1.4.1.2011.5.25.250.16.2.5			The hwEntSipProfile group.
hwEntSipSrvLogicGroup	1.3.6.1.4.1.2011.5.25.250.16.2.6			The hwEntSipSrvLogic group.
hwEntSipAgDmmParaGroup	1.3.6.1.4.1.2011.5.25.250.16.2.7			The hwEntSipAgDmmPara group.
hwEntSipAgUserGroupGroup	1.3.6.1.4.1.2011.5.25.250.16.2.8			The hwEntSipAgUserGroup group.
hwEntSipAgSoftNumberParaGroup	1.3.6.1.4.1.2011.5.25.250.16.2.9			The hwEntSipAgSoftNumberPara group.
hwEntSipAgSoftStringParaGroup	1.3.6.1.4.1.2011.5.25.250.16.2.10			The hwEntSipAgSoftStringPara group.
hwEntSipAgSoftStringParaRunningGroup	1.3.6.1.4.1.2011.5.25.250.16.2.11			The hwEntSipAgSoftStringParaRunningGroup group.
hwEntFaxModemParaGroup	1.3.6.1.4.1.2011.5.25.250.16.2.12			The hwEntFaxModemPara group.
hwEntDtmfParaGroup	1.3.6.1.4.1.2011.5.25.250.16.2.13			The hwEntDtmfPara group.
hwEntNteGroup	1.3.6.1.4.1.2011.5.25.250.16.2.14			The hwEntNte group.
hwEntRedundancyGroup	1.3.6.1.4.1.2011.5.25.250.16.2.15			The hwEntRedundancy group.

RFC description

Manages SIP Access Gateway (SIPAG) configuration for SIP-based VoIP call management.

Start monitoring Huawei enterprise voice gateway (SIP trunk/agent) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HUAWEI-ENT-VOICE-SIPAG-MIB

What Is HUAWEI-ENT-VOICE-SIPAG-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description