HP-SN-MPLS-LSR-MIB

All MIBs › HP-SN-MPLS-LSR-MIB

Organization: Multiprotocol Label Switching (MPLS) Working Group

Last Updated: 2002-01-04

Category: MPLS and Traffic Engineering, Protocol: MPLS, Vendor: HP/HPE

Description: SNMP MIB from HP ServerNet (with Foundry heritage) covering the MPLS Label Switch Router (LSR) label table and forwarding behavior on HP SN network devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HP-SN-MPLS-LSR-MIB?

HP-SN-MPLS-LSR-MIB is an HP SN (Foundry-heritage) SNMP MIB module implementing the IETF MPLS Label Switch Router (LSR) MIB (RFC 3031) for HP's Foundry-derived ServerNet/SN series routing switches. It exposes MPLS interface configuration and performance data, including per-interface label ranges, bandwidth allocation, and label-switching participation state, plus fault notifications for the LSR subsystem. Because MPLS forwarding correctness depends on healthy label allocation and adequate link bandwidth, this MIB is used to monitor the operational health of MPLS-enabled interfaces -- tracking available vs. total bandwidth, label pool exhaustion, and interface participation state rather than classic CPU/memory/temperature sensors. It directly implements and depends on the IETF MPLS architecture defined in RFC 3031 and shares object naming conventions with the standard MPLS-LSR-MIB. It is deployed on HP/Foundry-heritage MPLS provider-edge or core routing switches in service-provider and large enterprise WAN backbones. Network engineers evaluating or troubleshooting this functionality can download the HP-SN-MPLS-LSR-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HP-SN-MPLS-LSR-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP/Foundry-heritage MPLS-capable routing switch
service-provider edge/core router

Monitoring Examples

An administrator polls mplsInterfaceConfTable/mplsInterfaceConfEntry to see per-interface mplsInterfaceLabelMinIn/mplsInterfaceLabelMaxIn and Out ranges alongside mplsInterfaceTotalBandwidth and mplsInterfaceAvailableBandwidth. A drop in mplsInterfaceAvailableBandwidth toward zero on a core-facing interface signals oversubscription or a misconfigured LSP reserving too much capacity. The mplsInterfacePerfTable supplements this with per-interface MPLS performance counters, and mplsLsrNotifications can alert when label participation state (mplsInterfaceLabelParticipationType) changes unexpectedly.

What Can Be Monitored

per-interface label range utilization
available vs total MPLS bandwidth
interface label participation state
MPLS interface performance counters
LSR fault notifications

Imported Objects

From HP-SN-MPLS-TC-MIB

MplsBitRate
MplsBurstSize
MplsInitialCreationSource
MplsLSPID
MplsLabel
mplsMIB	OBJECT-IDENTITY

From HP-SN-ROOT-MIB

snMpls

OBJECT-IDENTITY

From IANA-ADDRESS-FAMILY-NUMBERS-MIB

AddressFamilyNumbers

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero

From INET-ADDRESS-MIB

InetAddressIPv4
InetAddressIPv6
InetAddressType

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowPointer
RowStatus
StorageType
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using mplsInSegmentHCOctets OID:

Select a HP/Foundry-heritage MPLS-capable routing switch (Label Switch Router) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type mplsInSegmentHCOctets into the Find box to locate it in the OID tree, then select it and click OK. The total number of octets received. This is the 64 bit version of mplsInSegmentOctets. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
mplsLsrMIB	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2			This MIB contains managed object definitions for the Multiprotocol Label Switching (MPLS) Router as defined in: Rosen, E., Viswanathan, A., and R. Callon, Multiprotocol Label Switching Architecture, RFC 3031, January 2001.
mplsLsrObjects	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1
mplsInterfaceConfTable	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.1		not-accessible	This table specifies per-interface MPLS capability and associated information.
mplsInterfaceConfEntry	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.1.1		not-accessible	An entry in this table is created by an LSR for every interface capable of supporting MPLS. Each entry in this table will exist only if a corresponding entry in ifTable exists. If the associated entry in ifTable is deleted, the corresponding entry in this table must also be deleted shortly thereafter. The entry with index 0 represents the per-platform label space and contains parameters that apply to all interfaces that participate in the per-platform label space. Other entries defined in this table represent additional MPLS interfaces that may participate in either the per-platform or per-interface label spaces, or both. Additional information about label space participation of an interface is provided in the description clause of mplsInterfaceLabelParticipationType.
NUM mplsInterfaceConfIndex	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.1.1.1	InterfaceIndexOrZero	not-accessible	This is a unique index for an entry in the MplsInterfaceConfTable. A non-zero index for an entry indicates the ifIndex for the corresponding interface entry in of the MPLS-layer in the ifTable. Note that the per-platform label space may apply to several interfaces, and therefore the configuration of the per-platform label space interface parameters will apply to all of the interfaces that are participating in the per-platform label space.
MPL mplsInterfaceLabelMinIn	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.1.1.2	MplsLabel	read-only	This is the minimum value of an MPLS label that this LSR is willing to receive on this interface.
MPL mplsInterfaceLabelMaxIn	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.1.1.3	MplsLabel	read-only	This is the maximum value of an MPLS label that this LSR is willing to receive on this interface.
MPL mplsInterfaceLabelMinOut	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.1.1.4	MplsLabel	read-only	This is the minimum value of an MPLS label that this LSR is willing to send on this interface.
MPL mplsInterfaceLabelMaxOut	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.1.1.5	MplsLabel	read-only	This is the maximum value of an MPLS label that this LSR is willing to send on this interface.
MPL mplsInterfaceTotalBandwidth	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.1.1.6	MplsBitRate	read-only	This value indicates the total amount of usable bandwidth on this interface and is specified in kilobits per second (Kbps). This variable is not applicable when applied to the interface with index 0. When this value cannot be measured, this value should contain the nominal bandwidth.
MPL mplsInterfaceAvailableBandwidth	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.1.1.7	MplsBitRate	read-only	This value indicates the total amount of available bandwidth available on this interface and is specified in kilobits per second (Kbps). This value is calculated as the difference between the amount of bandwidth currently in use and that specified in mplsInterfaceTotalBandwidth. This variable is not applicable when applied to the interface with index 0. When this value cannot be measured, this value should contain the nominal bandwidth.
BIT mplsInterfaceLabelParticipationType	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.1.1.8	Bits	read-only	Either the perPlatform(0) or perInterface(1) bit MUST be set. If the value of the mplsInterfaceConfIndex for this entry is zero, then only the perPlatform(0) bit MUST be set and the perInterface(1) bit is meaningless. If the perInterface(1) bit is set then the value of mplsInterfaceLabelMinIn, mplsInterfaceLabelMaxIn, mplsInterfaceLabelMinOut, and mplsInterfaceLabelMaxOut for this entry reflect the label ranges for this interface. If only the perPlatform(0) bit is set, then the value of mplsInterfaceLabelMinIn, mplsInterfaceLabelMaxIn, mplsInterfaceLabelMinOut, and mplsInterfaceLabelMaxOut for this entry must be identical to the instance of these objects with index 0.
mplsInterfacePerfTable	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.2		not-accessible	This table provides MPLS performance information on a per-interface basis.
mplsInterfacePerfEntry	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.2.1		not-accessible	An entry in this table is created by the LSR for every interface capable of supporting MPLS. Its is an extension to the mplsInterfaceConfEntry table.
G32 mplsInterfaceInLabelsUsed	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.2.1.1	Gauge32	read-only	This object counts the number of labels that are in use at this point in time on this interface in the incoming direction. If the interface participates in the per-platform label space only, then this instance of this object MUST be identical with the instance with index 0. If the interface participates in the per-interface label space, then this instance of this object MUST represent the number of of per- interface labels that are in use at this point in time on this interface.
C32 mplsInterfaceFailedLabelLookup	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.2.1.2	Counter32	read-only	This object counts the number of labeled packets that have been received on this interface and were discarded because there was no matching cross- connect entry. This object MUST count on a per- interface basis regardless of which label space the interface participates in.
G32 mplsInterfaceOutLabelsUsed	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.2.1.3	Gauge32	read-only	This object counts the number of top-most labels in the outgoing label stacks that are in use at this point in time on this interface. This object MUST count on a per-interface basis regardless of which label space the interface participates in.
C32 mplsInterfaceOutFragments	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.2.1.4	Counter32	read-only	This object counts the number of outgoing MPLS packets that required fragmentation before transmission on this interface. This object MUST count on a per-interface basis regardless of which label space the interface participates in.
mplsInSegmentTable	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.3		not-accessible	This table contains a collection of incoming segments to an LSR.
mplsInSegmentEntry	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.3.1		not-accessible	An entry in this table represents one incoming segment. An entry can be created by a network administrator or an SNMP agent, or an MPLS signaling protocol. The creator of the entry is denoted by mplsInSegmentOwner. An entry in this table is indexed by the ifIndex of the incoming interface and the (top) label. The value of mplsInSegmentRowStatus cannot be active(1)unless the ifTable entry corresponding to mplsInSegmentIfIndex exists.
NUM mplsInSegmentIfIndex	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.3.1.1	InterfaceIndexOrZero	not-accessible	This is a unique index for an entry in the MplsInSegmentTable. This value represents the interface index for the incoming MPLS interface. A value of zero represents an incoming label from the per-platform label space. In this case, the mplsInSegmentLabel is interpreted to be an MPLS-type label.
MPL mplsInSegmentLabel	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.3.1.2	MplsLabel	not-accessible	The incoming label for this segment.
I32 mplsInSegmentNPop	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.3.1.3	Integer32	read-create	The number of labels to pop from the incoming packet. Normally only the top label is popped from the packet and used for all switching decisions for that packet. Note that technologies which do not support label popping should set this value to its default value of 1. This object cannot be modified if mplsInSegmentRowStatus is active(1).
ADR mplsInSegmentAddrFamily	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.3.1.4	AddressFamilyNumbers	read-create	The IANA address family [IANAFamily] of the incoming packet. A value of other(0) indicates that the family type is either unknown or undefined. This object cannot be modified if mplsInSegmentRowStatus is active(1).
U32 mplsInSegmentXCIndex	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.3.1.5	Unsigned32	read-only	Index into mplsXCTable which identifies which cross- connect entry this segment is part of. A value of zero indicates that this entry is not referred to by any cross-connect entry. When a cross-connect entry is created which this in-segment is a part of, this object is automatically updated to reflect the value of mplsXCIndex of that cross-connect entry.
MPL mplsInSegmentOwner	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.3.1.6	MplsInitialCreationSource	read-create	Denotes the entity that created and is responsible for managing this segment. This object cannot be modified if mplsInSegmentRowStatus is active(1).
NUM mplsInSegmentTrafficParamPtr	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.3.1.7	RowPointer	read-create	This variable represents a pointer to the traffic parameter specification for this in-segment. This value may point at an entry in the mplsTrafficParamTable to indicate which mplsTrafficParamEntry is to be assigned to this segment. This value may optionally point at an externally defined traffic parameter specification table. A value of zero-dot-zero indicates best-effort treatment. By having the same value of this object, two or more segments can indicate resource sharing. This object cannot be modified if mplsInSegmentRowStatus is active(1).
ROW mplsInSegmentRowStatus	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.3.1.8	RowStatus	read-create	This variable is used to create, modify, and/or delete a row in this table.
STO mplsInSegmentStorageType	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.3.1.9	StorageType	read-create	This variable indicates the storage type for this object. This object cannot be modified if mplsInSegmentRowStatus is active(1). If this variable is set to readOnly(5), and the corresponding TFIB entry is removed, then the agent must remove this row shortly thereafter.
mplsInSegmentPerfTable	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.4		not-accessible	This table contains statistical information for incoming MPLS segments to an LSR.
mplsInSegmentPerfEntry	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.4.1		not-accessible	An entry in this table contains statistical information about one incoming segment which was configured in the mplsInSegmentTable. The counters in this entry should behave in a manner similar to that of the interface.
C32 mplsInSegmentOctets	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.4.1.1	Counter32	read-only	This value represents the total number of octets received by this segment.
C32 mplsInSegmentPackets	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.4.1.2	Counter32	read-only	Total number of packets received by this segment.
C32 mplsInSegmentErrors	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.4.1.3	Counter32	read-only	The number of errored packets received on this segment.
C32 mplsInSegmentDiscards	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.4.1.4	Counter32	read-only	The number of labeled packets received on this in- segment, which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a labeled packet could be to free up buffer space.
C64 mplsInSegmentHCOctetsEx	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.4.1.5	Counter64	read-only	The total number of octets received. This is the 64 bit version of mplsInSegmentOctets.
TIM mplsInSegmentPerfDiscontinuityTime	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.4.1.6	TimeStamp	read-only	The value of sysUpTime on the most recent occasion at which any one or more of this segment's Counter32 or Counter64 suffered a discontinuity. If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value.
U32 mplsOutSegmentIndexNext	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.5	Unsigned32	read-only	This object contains the next appropriate value to be used for mplsOutSegmentIndex when creating entries in the mplsOutSegmentTable. If the number of unassigned entries is exhausted, this object will take on the value of 0. To obtain the mplsOutSegmentIndex value for a new entry, the manager must first issue a management protocol retrieval operation to obtain the current value of this object. The agent should modify the value to reflect the next unassigned index after each retrieval operation. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
mplsOutSegmentTable	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.6		not-accessible	This table contains a representation of the outgoing segments from an LSR.
mplsOutSegmentEntry	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.6.1		not-accessible	An entry in this table represents one outgoing segment. An entry can be created by a network administrator or an SNMP agent, or an MPLS signaling protocol. The object mplsOutSegmentOwner indicates the creator of this entry. The value of mplsOutSegmentRowStatus cannot be active(1)unless the ifTable entry corresponding to mplsOutSegmentIfIndex exists.
U32 mplsOutSegmentIndex	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.6.1.1	Unsigned32	not-accessible	This value contains a unique index for this row. While a value of 0 is not valid as an index for this row it can be supplied as a valid value to index mplsXCTable to access entries for which no out- segment has been configured.
NUM mplsOutSegmentIfIndex	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.6.1.2	InterfaceIndexOrZero	read-create	This value must contain the interface index of the outgoing interface. This object may only take the value of 0 during the create-and-wait row creation operation if the management station has not yet set the value of this object. This object cannot be modified if mplsOutSegmentRowStatus is active(1). The mplsOutSegmentRowStatus cannot be set to active(1) until this object is set to a value corresponding to a valid ifEntry.
T/F mplsOutSegmentPushTopLabel	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.6.1.3	TruthValue	read-create	This value indicates whether or not a top label should be pushed onto the outgoing packet's label stack. The value of this variable MUST be set to true if the outgoing interface does not support pop- and-go (for example an ATM interface) or if it is a tunnel origination. Note that it is considered an error in the case that mplsOutSegmentPushTopLabel is set to false, but the cross-connect entry which refers to this out-segment has a non-zero mplsLabelStackIndex. The LSR MUST ensure that this situation does not happen. This object cannot be modified if mplsOutSegmentRowStatus is active(1).
MPL mplsOutSegmentTopLabel	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.6.1.4	MplsLabel	read-create	If mplsOutSegmentPushTopLabel is true then this represents the label that should be pushed onto the top of the outgoing packet's label stack. Otherwise this value SHOULD be set to 0 by the management station and MUST be ignored by the agent. This object cannot be modified if mplsOutSegmentRowStatus is active(1).
IPt mplsOutSegmentNextHopIpAddrType	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.6.1.5	InetAddressType	read-create	Indicates whether the next hop address is IPv4 or IPv6. Note that a value of unknown (0) is valid only when the outgoing interface is of type point-to- point. This object cannot be modified if mplsOutSegmentRowStatus is active(1).
ADR mplsOutSegmentNextHopIpv4Addr	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.6.1.6	InetAddressIPv4	read-create	IPv4 Address of the next hop. Its value is significant only when mplsOutSegmentNextHopIpAddrType is ipV4 (1), otherwise it SHOULD return a value of 0. This object cannot be modified if mplsOutSegmentRowStatus is active(1).
ADR mplsOutSegmentNextHopIpv6Addr	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.6.1.7	InetAddressIPv6	read-create	IPv6 address of the next hop. Its value is significant only when mplsOutSegmentNextHopIpAddrType is ipV6 (2), otherwise it SHOULD return a value of 0. This object cannot be modified if mplsOutSegmentRowStatus is active(1).
U32 mplsOutSegmentXCIndex	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.6.1.8	Unsigned32	read-only	Index into mplsXCTable which identifies which cross- connect entry this segment is part of. A value of zero indicates that this entry is not referred to by any cross-connect entry. When a cross-connect entry is created which this out-segment is a part of, this object is automatically updated to reflect the value of mplsXCIndex of that cross-connect entry.
MPL mplsOutSegmentOwner	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.6.1.9	MplsInitialCreationSource	read-create	Denotes the entity which created and is responsible for managing this segment. This object cannot be modified if mplsOutSegmentRowStatus is active(1).
NUM mplsOutSegmentTrafficParamPtr	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.6.1.10	RowPointer	read-create	This variable represents a pointer to the traffic parameter specification for this out-segment. This value may point at an entry in the mplsTrafficParamTable to indicate which mplsTrafficParamEntry is to be assigned to this segment. This value may optionally point at an externally defined traffic parameter specification table. A value of zero-dot-zero indicates best- effort treatment. By having the same value of this object, two or more segments can indicate resource sharing. This object cannot be modified if mplsOutSegmentRowStatus is active(1).
ROW mplsOutSegmentRowStatus	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.6.1.11	RowStatus	read-create	For creating, modifying, and deleting this row.
STO mplsOutSegmentStorageType	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.6.1.12	StorageType	read-create	This variable indicates the storage type for this object. This object cannot be modified if mplsOutSegmentRowStatus is active(1). If this variable is set to readOnly(5), and the corresponding TFIB entry is removed, then the agent must remove this row shortly thereafter.
mplsOutSegmentPerfTable	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.7		not-accessible	This table contains statistical information about outgoing segments from an LSR. The counters in this entry should behave in a manner similar to that of the interface.
mplsOutSegmentPerfEntry	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.7.1		not-accessible	An entry in this table contains statistical information about one outgoing segment configured in mplsOutSegmentTable.
C32 mplsOutSegmentOctets	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.7.1.1	Counter32	read-only	This value contains the total number of octets sent on this segment.
C32 mplsOutSegmentPackets	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.7.1.2	Counter32	read-only	This value contains the total number of packets sent on this segment.
C32 mplsOutSegmentErrors	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.7.1.3	Counter32	read-only	Number of packets that could not be sent due to errors on this segment.
C32 mplsOutSegmentDiscards	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.7.1.4	Counter32	read-only	The number of labeled packets received on this out- segment, which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a labeled packet could be to free up buffer space.
C64 mplsOutSegmentHCOctets	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.7.1.5	Counter64	read-only	Total number of octets sent. This is the 64 bit version of mplsOutSegmentOctets.
TIM mplsOutSegmentPerfDiscontinuityTime	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.7.1.6	TimeStamp	read-only	The value of sysUpTime on the most recent occasion at which any one or more of this segment's Counter32 or Counter64 suffered a discontinuity. If no such discontinuities have occurred since the last re- initialization of the local management subsystem, then this object contains a zero value.
U32 mplsXCIndexNext	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.8	Unsigned32	read-only	This object contains an appropriate value to be used for mplsXCIndex when creating entries in the mplsXCTable. The value 0 indicates that no unassigned entries are available. To obtain the value of mplsXCIndex for a new entry in the mplsXCTable, the manager issues a management protocol retrieval operation to obtain the current value of mplsXCIndex. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
mplsXCTable	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.9		not-accessible	This table specifies information for switching between LSP segments. It supports point-to-point, point-to-multipoint and multipoint-to-point connections. mplsLabelStackTable specifies the label stack information for a cross-connect LSR and is referred to from mplsXCTable.
mplsXCEntry	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.9.1		not-accessible	A row in this table represents one cross-connect entry. The following objects index it: - cross-connect index mplsXCIndex that uniquely identifies a group of cross-connect entries - interface index of the in-segment, mplsInSegmentIfIndex - incoming label(s), mplsInSegmentLabel - out-segment index, mplsOutSegmentIndex Originating LSPs: These are represented by using the special combination of values mplsInSegmentIfIndex=0 and mplsInSegmentLabel=0 as indexes. In this case the mplsOutSegmentIndex MUST be non-zero. Terminating LSPs: These are represented by using the special value mplsOutSegmentIndex=0 as index. Special labels: Entries indexed by reserved MPLS label values 0 through 15 imply terminating LSPs and MUST have mplsOutSegmentIfIndex = 0. Note that situations where LSPs are terminated with incoming label equal to 0, should have mplsInSegmentIfIndex = 0 as well, but can be distinguished from originating LSPs because the mplsOutSegmentIfIndex = 0. The mplsOutSegmentIfIndex MUST only be set to 0 in cases of terminating LSPs. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling protocol.
U32 mplsXCIndex	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.9.1.1	Unsigned32	not-accessible	Primary index for the conceptual row identifying a group of cross-connect segments.
MPL mplsXCLspId	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.9.1.2	MplsLSPID	read-create	This value identifies the label switched path that this cross-connect entry belongs to. This object cannot be modified if mplsXCRowStatus is active(1).
U32 mplsXCLabelStackIndex	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.9.1.3	Unsigned32	read-create	Primary index into mplsLabelStackTable identifying a stack of labels to be pushed beneath the top label. Note that the top label identified by the out- segment ensures that all the components of a multipoint-to-point connection have the same outgoing label. A value of 0 indicates that no labels are to be stacked beneath the top label. This object cannot be modified if mplsXCRowStatus is active(1).
T/F mplsXCIsPersistent	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.9.1.4	TruthValue	read-create	Denotes whether or not this cross-connect entry and associated in- and out-segments should be restored automatically after failures. This value MUST be set to false in cases where this cross-connect entry was created by a signaling protocol. This object cannot be modified if mplsXCRowStatus is active(1).
MPL mplsXCOwner	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.9.1.5	MplsInitialCreationSource	read-create	Denotes the entity that created and is responsible for managing this cross-connect. This object cannot be modified if mplsXCRowStatus is active(1).
ROW mplsXCRowStatus	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.9.1.6	RowStatus	read-create	For creating, modifying, and deleting this row.
STO mplsXCStorageType	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.9.1.7	StorageType	read-create	Defines the storage type for this object. This object cannot be modified if mplsXCRowStatus is active(1). If this variable is set to readOnly(5), and the corresponding TFIB entry is removed, then the agent must remove this row shortly thereafter.
INT mplsXCAdminStatus	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.9.1.8	INTEGER	read-create	The desired operational status of this segment.
INT mplsXCOperStatus	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.9.1.9	INTEGER	read-only	The actual operational status of this cross- connect.
I32 mplsMaxLabelStackDepth	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.10	Integer32	read-only	The maximum stack depth supported by this LSR.
U32 mplsLabelStackIndexNext	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.11	Unsigned32	read-only	This object contains an appropriate value to be used for mplsLabelStackIndex when creating entries in the mplsLabelStackTable. The value 0 indicates that no unassigned entries are available. To obtain an mplsLabelStackIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
mplsLabelStackTable	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.12		not-accessible	This table specifies the label stack to be pushed onto a packet, beneath the top label. Entries into this table are referred to from mplsXCTable.
mplsLabelStackEntry	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.12.1		not-accessible	An entry in this table represents one label which is to be pushed onto an outgoing packet, beneath the top label. An entry can be created by a network administrator or by an SNMP agent as instructed by an MPLS signaling protocol.
U32 mplsLabelStackIndex	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.12.1.1	Unsigned32	not-accessible	Primary index for this row identifying a stack of labels to be pushed on an outgoing packet, beneath the top label.
U32 mplsLabelStackLabelIndex	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.12.1.2	Unsigned32	not-accessible	Secondary index for this row identifying one label of the stack. Note that an entry with a smaller mplsLabelStackLabelIndex would refer to a label higher up the label stack and would be popped at a downstream LSR before a label represented by a higher mplsLabelStackLabelIndex at a downstream LSR.
MPL mplsLabelStackLabel	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.12.1.3	MplsLabel	read-create	The label to pushed.
ROW mplsLabelStackRowStatus	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.12.1.4	RowStatus	read-create	For creating, modifying, and deleting this row.
STO mplsLabelStackStorageType	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.12.1.5	StorageType	read-create	Defines the storage type for this object. If this variable is set to readOnly(5), and the corresponding TFIB entry is removed, then the agent must remove this row shortly thereafter.
U32 mplsTrafficParamIndexNext	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.13	Unsigned32	read-only	This object contains an appropriate value which will be used for mplsTrafficParamIndex when creating entries in the mplsTrafficParamTable. The value 0 indicates that no unassigned entries are available. To obtain the mplsTrafficParamIndex value for a new entry, the manager issues a management protocol retrieval operation to obtain the current value of this object. After each retrieval operation, the agent should modify the value to reflect the next unassigned index. After a manager retrieves a value the agent will determine through its local policy when this index value will be made available for reuse.
mplsTrafficParamTable	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.14		not-accessible	This table specifies the Traffic Parameter objects for in and out-segments.
mplsTrafficParamEntry	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.14.1		not-accessible	An entry in this table represents the TrafficParam objects for one or more in or out segments. A single entry can be pointed to by multiple segments indicating resource sharing.
U32 mplsTrafficParamIndex	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.14.1.1	Unsigned32	not-accessible	Uniquely identifies this row of the table. Note that zero represents an invalid index.
MPL mplsTrafficParamMaxRate	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.14.1.2	MplsBitRate	read-create	Maximum rate in kilobits/second.
MPL mplsTrafficParamMeanRate	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.14.1.3	MplsBitRate	read-create	Mean rate in kilobits/second.
MPL mplsTrafficParamMaxBurstSize	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.14.1.4	MplsBurstSize	read-create	Maximum burst size in bytes.
ROW mplsTrafficParamRowStatus	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.14.1.5	RowStatus	read-create	For creating, modifying, and deleting this row.
STO mplsTrafficParamStorageType	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.14.1.6	StorageType	read-create	The storage type for this object. If this variable is set to readOnly(5), and the corresponding TFIB entry is removed, then the agent must remove this row shortly thereafter.
T/F mplsXCTrapEnable	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.1.15	TruthValue	read-write	If this object is set to true(1), then it enables the emission of mplsXCUp and mplsXCDown notifications; otherwise these notifications are not emitted.
mplsLsrNotifications	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.2
mplsLsrNotifyPrefix	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.2.0
NTF mplsXCUp	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.2.0.1			This notification is generated when the mplsXCOperStatus object for one or more contiguous entries in mplsXCTable are about to enter the up(1) state from some other. The included values of mplsXCOperStatus MUST both be set equal to this other state. The two instances of mplsXCOperStatus in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For cases where a contiguous range of cross-connects have transitioned into the up(1) state at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single cross-connect entry, then the instance identifier (and values) of the two mplsXCOperStatus objects MUST be the identical.
NTF mplsXCDown	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.2.0.2			This notification is generated when the mplsXCOperStatus object for one or more contiguous entries in mplsXCTable are about to enter the down(2) state from some other. The included values of mplsXCOperStatus MUST both be set equal to this other state. The two instances of mplsXCOperStatus in this notification indicate the range of indexes that are affected. Note that all the indexes of the two ends of the range can be derived from the instance identifiers of these two objects. For cases where a contiguous range of cross-connects have transitioned into the down(2) state at roughly the same time, the device SHOULD issue a single notification for each range of contiguous indexes in an effort to minimize the emission of a large number of notifications. If a notification has to be issued for just a single cross-connect entry, then the instance identifier (and values) of the two mplsXCOperStatus objects MUST be the identical.
mplsLsrConformance	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3
mplsLsrGroups	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.1
mplsInterfaceGroup	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.1.1			Collection of objects needed for MPLS interface configuration and performance information.
mplsInSegmentGroup	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.1.2			Collection of objects needed to implement an in- segment.
mplsOutSegmentGroup	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.1.3			Collection of objects needed to implement an out- segment.
mplsXCGroup	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.1.4			Collection of objects needed to implement a cross-connect entry.
mplsXCOptionalGroup	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.1.5			Collection of optional objects for implementing a cross-connect entry.
mplsPerfGroup	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.1.6			Collection of objects providing performance information about an LSR.
mplsHCInSegmentPerfGroup	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.1.7			Object(s) providing performance information specific to out-segments for which the object mplsInterfaceInOctets wraps around too quickly.
mplsHCOutSegmentPerfGroup	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.1.8			Object(s) providing performance information specific to out-segments for which the object mplsInterfaceOutOctets wraps around too quickly.
mplsTrafficParamGroup	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.1.9			Object(s) required for supporting QoS resource reservation.
mplsXCIsPersistentGroup	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.1.10			Objects needed to support persistent cross- connects.
mplsXCIsNotPersistentGroup	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.1.11			Objects needed to support non-persistent cross- connects.
mplsLabelStackGroup	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.1.12			Objects needed to support label stacking.
mplsSegmentDiscontinuityGroup	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.1.13			A collection of objects providing information specific to segment discontinuities..
mplsLsrNotificationGroup	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.1.14			Set of notifications implemented in this module. None is mandatory.
mplsLsrCompliances	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.2
mplsLsrModuleCompliance	1.3.6.1.4.1.11.2.3.7.11.12.2.15.15.2.3.2.1			Compliance statement for agents that support the MPLS LSR MIB.

RFC description

HP ServerNet (Foundry-heritage) SNMP MIB for MPLS Label Switch Router (LSR) label table and forwarding on HP SN network devices.

Start monitoring HP/Foundry-heritage MPLS-capable routing switch (Label Switch Router) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HP-SN-MPLS-LSR-MIB