HPN-ICF-USERLOG-MIB

All MIBs › HPN-ICF-USERLOG-MIB

Last Updated: 2003-04-10

Category: Alarm and Event Management, Vendor: H3C/HH3C, Vendor: HP/HPE

Description: Logs and manages per-user network access records for accounting and auditing on HP/Comware access devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HPN-ICF-USERLOG-MIB?

HPN-ICF-USERLOG-MIB is an HP Networking (H3C-derived ICF platform) proprietary MIB configuring user-activity logging for NAT and flow sessions. Its NAT-userlog objects cover version, syslog enable, source IP, flow-begin/active-time settings, a per-slot config table (enable, ACL number, host address, UDP port), and a per-slot runtime table (total/failed entries and packets, clear-stats action), with matching Flow-userlog objects (version, syslog, source IP, flow-begin/active-time). As a configuration/performance MIB it lets an administrator confirm NAT/flow logging destination and watch logged-entry success/failure counts on an HP Networking device. It is deployed on HP Networking (H3C-derived) equipment (NAT/flow user logging). Engineers can download the HPN-ICF-USERLOG-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HPN-ICF-USERLOG-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP Networking (H3C-derived) equipment (NAT/flow user logging)

Monitoring Examples

An administrator checks hpnicfUserlogNatFailedEntries and hpnicfUserlogNatHostAddress to diagnose NAT session-log delivery failures on an HP Networking device.

What Can Be Monitored

NAT/flow user-log delivery destination and success/failure counts

Imported Objects

From HPN-ICF-OID-MIB

hpnicfRhw

OBJECT-IDENTITY

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE

How to Use in IPNetwork Monitor

Example using hpnicfUserlogNatTotalEntries OID:

Select an HP Networking (H3C-derived) equipment (NAT/flow user activity logging) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hpnicfUserlogNatTotalEntries into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The total number of NAT flow entries which are logged. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hpnicfUserLogMIB	1.3.6.1.4.1.11.2.14.11.15.8.18			The HPN-ICF-USERLOG-MIB contains objects to Manage configuration and Monitor running state for userlog feature.
hpnicfUserlogObjects	1.3.6.1.4.1.11.2.14.11.15.8.18.1
hpnicfUserlogNatObjects	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1
I32 hpnicfUserlogNatVersion	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.1	Integer32	read-only	NAT LOG version. Currently only version 1 is developed.
I32 hpnicfUserlogNatSyslog	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.2	Integer32	read-write	NAT LOG format. If 1, LOG format is sysLog. If 0, LOG format is UDP packet. UDP packet is the default format, and is recommended.
IP hpnicfUserlogNatSourceIP	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.3	IpAddress	read-write	The Source IP address of NAT LOG UDP packet.
I32 hpnicfUserlogNatFlowBegin	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.4	Integer32	read-write	Log the NAT flow when it is created. If 1, this function is enabled. If 0, this function is disabled. This function will be used when real-time monitor required.
I32 hpnicfUserlogNatActiveTime	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.5	Integer32	read-write	The active time for long-time existed NAT flow. Unit: minute. Range: 10 minutes ~ 120 minutes. When setting it, NAT flow can be logged after an interval of active time. This function will be used when real-time monitor required. The default value 0 means real-time monitor function is disabled.
hpnicfUserlogNatSlotCfgInfoTable	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.6		not-accessible	A table of NAT LOG configuration information for the specified slot.
hpnicfUserlogNatSlotCfgInfoEntry	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.6.1		not-accessible	NAT LOG Configuration Information Entry for a slot.
I32 hpnicfUserlogNatCfgSlotNumber	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.6.1.1	Integer32	read-only	Slot number. Specify which slot is configured with NAT LOG.
I32 hpnicfUserlogNatEnable	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.6.1.2	Integer32	read-write	The NAT LOG feature Enable status. If 1, NAT LOG is enbled. If 0, NAT LOG is disabled.
I32 hpnicfUserlogNatAclNumber	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.6.1.3	Integer32	read-write	Access-list number. The value 0 means no ACL is specified. Only when NAT LOG is enabled, can ACL be configured. Only NAT flow which match the ACL will be logged.
IP hpnicfUserlogNatHostAddress	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.6.1.4	IpAddress	read-write	The IP address of NAT LOG server.
I32 hpnicfUserlogNatUdpPort	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.6.1.5	Integer32	read-write	The UDP Port Number of NAT LOG UDP packet.
hpnicfUserlogNatSlotRunInfoTable	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.7		not-accessible	A table of NAT LOG running information for the specified slot.
hpnicfUserlogNatSlotRunInfoEntry	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.7.1		not-accessible	NAT LOG Running Information Entry for a slot.
I32 hpnicfUserlogNatRunSlotNumber	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.7.1.1	Integer32	read-only	Slot number. Specify on which slot the NAT LOG statistics displayed.
C32 hpnicfUserlogNatTotalEntriesEx	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.7.1.2	Counter32	read-only	The total number of NAT flow entries which are logged.
C32 hpnicfUserlogNatTotalPackets	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.7.1.3	Counter32	read-only	The total number of NAT LOG UDP packets generated by the router.
C32 hpnicfUserlogNatFailedEntries	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.7.1.4	Counter32	read-only	The total number of NAT flow entries failed in outputting.
C32 hpnicfUserlogNatFailedPackets	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.7.1.5	Counter32	read-only	The total number of NAT LOG UDP packets failed in outputting.
I32 hpnicfUserlogNatClearRunStat	1.3.6.1.4.1.11.2.14.11.15.8.18.1.1.7.1.6	Integer32	read-write	Clear the running statistics for NAT LOG. Write-only. If 1, the running statistics for NAT LOG is resetted. Other value is invalid.
hpnicfUserlogFlowObjects	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2
I32 hpnicfUserlogFlowVersion	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.1	Integer32	read-only	BAS FLOW LOG version. Currently only version 1 is developed.
I32 hpnicfUserlogFlowSyslog	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.2	Integer32	read-write	BAS FLOW LOG format. If 1, LOG format is sysLog. If 0, LOG format is UDP packet. UDP packet is the default format, and is recommended.
IP hpnicfUserlogFlowSourceIP	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.3	IpAddress	read-write	The Source IP address of BAS FLOW LOG UDP packet.
I32 hpnicfUserlogFlowFlowBegin	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.4	Integer32	read-write	Log the BAS flow when it is created. If 1, this function is enabled. If 0, this function is disabled. This function will be used when real-time monitor required.
I32 hpnicfUserlogFlowActiveTime	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.5	Integer32	read-write	The active time for long-time existed BAS flow. Unit: minute. Range: 10 minutes ~ 120 minutes. When setting it, BAS flow can be logged after an internal of active time. This function will be used when real-time monitor required. The default value 0 means real-time monitor function is disabled.
hpnicfUserlogFlowSlotCfgInfoTable	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.6		not-accessible	A table of BAS FLOW LOG configuration information for the specified slot.
hpnicfUserlogFlowSlotCfgInfoEntry	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.6.1		not-accessible	BAS FLOW LOG Configuration Information Entry for a slot.
I32 hpnicfUserlogFlowCfgSlotNumber	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.6.1.1	Integer32	read-only	Slot number. Specify which slot is configured with BAS FLOW LOG.
I32 hpnicfUserlogFlowEnable	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.6.1.2	Integer32	read-write	The BAS FLOW LOG feature Enable status. If 1, BAS FLOW LOG is enbled. If 0, BAS FLOW LOG is disabled.
I32 hpnicfUserlogFlowAclNumber	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.6.1.3	Integer32	read-write	Access-list number. The value 0 means no ACL is specified. Only when BAS FLOW LOG is enabled, can ACL be configured. Only BAS flow which match the ACL will be logged.
IP hpnicfUserlogFlowHostAddress	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.6.1.4	IpAddress	read-write	The IP address of BAS FLOW LOG server.
I32 hpnicfUserlogFlowUdpPort	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.6.1.5	Integer32	read-write	The UDP Port Number of BAS FLOW LOG UDP packet.
hpnicfUserlogFlowSlotRunInfoTable	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.7		not-accessible	A table of BAS FLOW LOG running information for the specified slot.
hpnicfUserlogFlowSlotRunInfoEntry	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.7.1		not-accessible	Running Information Entry for a slot.
I32 hpnicfUserlogFlowRunSlotNumber	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.7.1.1	Integer32	read-only	Slot number. Specify on which slot the BAS FLOW LOG statistics displayed.
C32 hpnicfUserlogFlowTotalEntries	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.7.1.2	Counter32	read-only	The total number of BAS FLOW Entries which are logged.
C32 hpnicfUserlogFlowTotalPackets	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.7.1.3	Counter32	read-only	The total number of FLOW LOG UDP packet generated by the router.
C32 hpnicfUserlogFlowFailedEntries	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.7.1.4	Counter32	read-only	The total number of BAS FLOW entries failed in outputting.
C32 hpnicfUserlogFlowFailedPackets	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.7.1.5	Counter32	read-only	The total number of BAS FLOW LOG UDP packet failed in outputting.
I32 hpnicfUserlogFlowClearRunStat	1.3.6.1.4.1.11.2.14.11.15.8.18.1.2.7.1.6	Integer32	read-write	Clear the running statistics for FLOW LOG. Write-only. If 1, the running statistics for FLOW LOG is resetted. Other value is invalid.
hpnicfUserlogAccessObjects	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3
I32 hpnicfUserlogAccessVersion	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.1	Integer32	read-only	BAS ACCESS LOG version. Currently only version 1 is developed.
I32 hpnicfUserlogAccessSyslog	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.2	Integer32	read-write	BAS ACCESS LOG format. If 1, LOG format is sysLog; If 0, LOG format is UDP packet. UDP packet is the default format, and is recommended.
IP hpnicfUserlogAccessSourceIP	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.3	IpAddress	read-write	The Source IP address of BAS ACCESS LOG UDP packet.
hpnicfUserlogAccessSlotCfgInfoTable	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.4		not-accessible	A table of BAS ACCESS LOG configuration information for the specified slot.
hpnicfUserlogAccessSlotCfgInfoEntry	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.4.1		not-accessible	BAS ACCESS LOG Configuration Information Entry for a slot.
I32 hpnicfUserlogAccessCfgSlotNumber	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.4.1.1	Integer32	read-only	Slot number. Specify which slot is configured with BAS ACCESS LOG.
I32 hpnicfUserlogAccessEnable	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.4.1.2	Integer32	read-write	The BAS ACCESS LOG feature Enable status. If 1, BAS ACCESS LOG is enbled. If 0, BAS ACCESS LOG is disabled.
IP hpnicfUserlogAccessHostAddress	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.4.1.3	IpAddress	read-write	The IP address of BAS ACCESS LOG server.
I32 hpnicfUserlogAccessUdpPort	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.4.1.4	Integer32	read-write	The UDP Port Number of BAS ACCESS LOG UDP packet.
hpnicfUserlogAccessSlotRunInfoTable	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.5		not-accessible	A table of BAS ACCESS LOG running information for the specified slot.
hpnicfUserlogAccessSlotRunInfoEntry	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.5.1		not-accessible	Running Information Entry for a slot.
I32 hpnicfUserlogAccessRunSlotNumber	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.5.1.1	Integer32	read-only	Slot number. Specify on which slot the BAS ACCESS LOG statistics displayed.
C32 hpnicfUserlogAccessTotalEntries	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.5.1.2	Counter32	read-only	The total number of BAS ACCESS Records which are logged.
C32 hpnicfUserlogAccessTotalPackets	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.5.1.3	Counter32	read-only	The total number of ACCESS LOG UDP packet generated by the router.
C32 hpnicfUserlogAccessFailedEntries	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.5.1.4	Counter32	read-only	The total number of BAS ACCESS entries failed in outputting.
C32 hpnicfUserlogAccessFailedPackets	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.5.1.5	Counter32	read-only	The total number of BAS ACCESS LOG UDP packet failed in outputting.
I32 hpnicfUserlogAccessClearRunStat	1.3.6.1.4.1.11.2.14.11.15.8.18.1.3.5.1.6	Integer32	read-write	Clear the running statistics for ACCESS LOG. Write-only. If 1, the running statistics for ACCESS LOG is resetted. Other value is invalid.
hpnicfUserlogNotifications	1.3.6.1.4.1.11.2.14.11.15.8.18.2
hpnicfUserlogConformance	1.3.6.1.4.1.11.2.14.11.15.8.18.3
hpnicfUserlogCompliances	1.3.6.1.4.1.11.2.14.11.15.8.18.3.1
hpnicfUserlogCompliance	1.3.6.1.4.1.11.2.14.11.15.8.18.3.1.1			The compliance statement for entities which implement the Userlog mib.
hpnicfUserlogGroups	1.3.6.1.4.1.11.2.14.11.15.8.18.3.2
hpnicfUserlogMandatoryGroup	1.3.6.1.4.1.11.2.14.11.15.8.18.3.2.1			A collection of objects providing mandatory Userlog information.
hpnicfUserlogConfigGroup	1.3.6.1.4.1.11.2.14.11.15.8.18.3.2.2			All configurable parameters of Userlog feature.
hpnicfUserlogInfoGroup	1.3.6.1.4.1.11.2.14.11.15.8.18.3.2.3			All running information of Userlog feature.

RFC description

User logging configuration for HP/H3C network equipment including NAT logging and flow tracking.

Start monitoring HP Networking (H3C-derived) equipment (NAT/flow user activity logging) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HPN-ICF-USERLOG-MIB