HP-SN-AGENT-MIB

All MIBs › HP-SN-AGENT-MIB

Category: Device Management, Vendor: HP/HPE

Description: HP ServerNet (Foundry-heritage) SNMP agent MIB providing system-level management and agent information for HP SN network devices.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HP-SN-AGENT-MIB?

HP-SN-AGENT-MIB is HP's ServerNet/Foundry-heritage system agent MIB providing chassis-level identification and hardware status for HP network switches, within the core device/hardware-management area. It exposes system and chassis inventory data (type, serial number, board descriptions, port totals) directly alongside hardware health indicators — power supply status, fan status, and status/traffic/media LED states. This MIB is squarely a hardware-monitoring MIB: snChasPwrSupplyStatus and snChasFanStatus let an administrator directly detect a failed power supply or fan before it causes overheating or a chassis shutdown, while snChasMainBrdDescription/snChasExpBrdDescription with their port-total counters confirm the physical hardware configuration matches expectations. It typically complements the standard ENTITY-MIB and IF-MIB for a fuller physical/logical inventory picture, since this Foundry-heritage chassis MIB predates or supplements those standards. Typical deployment is HP/Foundry-heritage chassis-based switches where NOC staff poll chassis health objects and enable trap generation for proactive power/fan fault alerting. Engineers can download the HP-SN-AGENT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HP-SN-AGENT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP/Foundry-heritage chassis-based network switches

Monitoring Examples

An administrator would poll snChasPwrSupplyStatus and snChasFanStatus regularly; a status value indicating failed or not-installed on either flags an imminent hardware fault requiring physical intervention. snChasMainBrdDescription and snChasMainPortTotal (plus the expansion equivalents snChasExpBrdDescription/snChasExpPortTotal) let an inventory system confirm the chassis's actual populated port count, while snChasSerNum ties the polled data to a specific physical unit. Enabling snChasEnablePwrSupplyTrap causes the device to proactively send an SNMP trap the moment a power supply changes status, rather than waiting for the next poll cycle, which is critical for catching sudden failures in production.

What Can Be Monitored

power supply status
fan status
chassis/board type and serial number
main and expansion board port counts
status/traffic/media LED states
power-supply-failure trap enable state

Imported Objects

From HP-SN-ROOT-MIB

snAgentSys	OBJECT-IDENTITY
snChassis	OBJECT-IDENTITY
snStack	OBJECT-IDENTITY

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
TimeTicks

OIDs

OID symbolic	OID numeric	Type	Access	Description
snChasGen	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1
STR snChasType	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.1	DisplayString	read-only	The chassis type represents the type of Foundry product being managed.
STR snChasSerNum	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.2	DisplayString	read-only	The serial number of the chassis. If the serial number is unknown or unavailable then the value should be a zero length string.
INT snChasPwrSupplyStatus	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.3	INTEGER	read-only	A bit array that contains the value of the Chassis Power Supplies. This is a packed bit string; the 2 power supplies status are encoded into 4 bits (a nibble). There are multiple power supplies per chassis in this release. The following shows the meaning of each bit: (bit 0 is the least significant bit). bit position meaning ------------ ------- 12-31 reserved 11 Power Supply 4 DC (0=bad, 1=good). 10 Power Supply 3 DC (0=bad, 1=good). 9 Power Supply 4 present status (0=present, 1=not-present). 8 Power Supply 3 present status (0=present, 1=not-present). 4-7 reserved 3 Power Supply 2 DC (0=bad, 1=good). 2 Power Supply 1 DC (0=bad, 1=good). 1 Power Supply 2 present status (0=present, 1=not-present). 0 Power Supply 1 present status (0=present, 1=not-present).
INT snChasFanStatus	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.4	INTEGER	read-only	A bit array that contains the value of the fan status. This is a packed bit string. The status of each fan is encoded into one bit. bit value meaning --------- ------- 0 fan failure. 1 fan good. There are two fans per VLAN Switch chassis in this release. The following shows the meaning of each bit: (bit 0 is the least significant bit). bit position meaning ------------ ------- 4-31 reserved 3 fan4 status 2 fan3 status 1 fan2 status 0 fan1 status
STR snChasMainBrdDescription	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.5	DisplayString	read-only	The main board description string. (It is obsoleted for Chassis Product)
INT snChasMainPortTotal	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.6	INTEGER	read-only	The total number of ports for the main board. (It is obsoleted for Chassis Product)
STR snChasExpBrdDescription	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.7	DisplayString	read-only	The expansion board description string. Expansion board are those boards attaching on the main board. (It is obsoleted for Chassis Product)
INT snChasExpPortTotal	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.8	INTEGER	read-only	The total number of ports for the expansion board. (It is obsoleted for Chassis Product)
INT snChasStatusLeds	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.9	INTEGER	read-only	A bit array that contains the value of the front panel status LEDs. This is a bit-map; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Status LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (Link off) 1 on (Link on) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
INT snChasTrafficLeds	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.10	INTEGER	read-only	A bit array that contains the value of the front panel traffic LEDs. This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Traffic LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (no traffic) 1 on (traffic) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
INT snChasMediaLeds	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.11	INTEGER	read-only	A bit array that contains the value of the front panel media LEDs. This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Media LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning --------- ------- 0 half duplex 1 full duplex The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 ---------
INT snChasEnablePwrSupplyTrap	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.12	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate power supply failure traps.
OCT snChasMainBrdId	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.13	OCTET STRING	read-only	The main board identifier, which can uniquely identify a board type. It is an encoded octet string with the following meaning: octet 0 - octet string format version, which identifies the format of this string. If format version octet has the value 1, the octets after the version octet have the following meaning: octet 1 - product type, FIWG=0x57, FIBB=0x42, FIMLS=0x4D NI=0x4E, TI=0x54, TIRT=0x52 octet 2 - board type, POWERPC=1, ALPHA=2 The length of the octet string is 27. If format version octet has the value 2, the octets after the version octet have the following meaning: octet 1 - product type: BI_WG 0x57 BI_BB 0x42 BI_NI 0x4E octet 2 - module type: FI_MASTER_FIBER_8G 0x7 FI_MASTER_FIBER_4G 0x5 FI_MASTER_FIBER_2G 0x4 FI_SLAVE_COPPER_24 0xB MASTER_FIBER_8G 0x0 MASTER_FIBER_4G 0x1 MASTER_FIBER_2G 0x12 MASTER_FIBER_0G 0x14 MASTER_COPPER_16 0x2 MASTER_COPPER_8G 0x6 MASTER_COPPER_12_2 0x9 SLAVE_FIBER_8G 0x8 SLAVE_FIBER_4G 0x3 SLAVE_COPPER_20 0xA SLAVE_COPPER_24 0xA SLAVE_100FX_8 0xD SLAVE_100FX_16 0xC SLAVE_COPPER_8G 0xE SLAVE_COPPER_16_2 0xF STACK_FIBER_8G 0x10 STACK_COPPER_8G 0x11 SLAVE_100FX_24 0x13 The length of the octet string is 28. Both format version 1 and 2: octet 3 - processor type, PVR_M603=3, PVR_M604=4, PVR_M603E=6, PVR_M603EV=7, PVR_M604E=9 octet 4 to octet 5 - processor speed in MHz octet 6 - MAC type: MAC_SEEQ_10_100=1, MAC_DEC_10_100=2, MAC_SEEQ_1000=5, MAC_GMAC_1000=6, MAC_VLSI_1000=9 octet 7 - PHY type, PHY_NONE=0, PHY_QSI=1, PHY_ICS=3, PHY_NATIONAL=4, PHY_LEVEL1=6, PHY_LEVEL16=7, PHY_LEVEL24=8 octet 8 - port type, COPPER=0, FIBER=1 octet 9 - fiber port type, NONFIBER=0, SX_FIBER=1, LX_FIBER=2, LHX_FIBER=3, LX_SX_FIBER=4, LHB_FIBER=5 octet 10 to octet 13 - DRAM size in KBytes octet 14 to octet 17 - boot flash size in KBytes octet 18 to octet 21 - code flash size in KBytes octet 22 to octet 27 - serial number. Format version 1 only: octet 28 - chassis backplane type. chassis4000 = 0x00 chassis8000 = 0x04 Turbo8 = 0x07 (stack2) FastIron2 = 0x06 (stack1)
OCT snChasExpBrdId	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.14	OCTET STRING	read-only	The expansion board identifier. Expansion board are those boards attaching on the main board. It is an encoded octet string with the following meaning: octet 0 - octet string format version, which identifies the format of this string. If format version octet has the value 1, the octets after the version octet have the following meaning: octet 1 - expansion board type, HUNDRED_MEG_1PORT=1, HUNDRED_MEG_2PORT=2, HUNDRED_MEG_1PORT_COPPER=3, HUNDRED_MEG_2PORT_COPPER=4, HUNDRED_MEG_2PORT_LX=5, GIGA_1PORT=8, GIGA_2PORT=9 octet 2 - fiber port type, NONFIBER=0, SX_FIBER=1, LX_FIBER=2, LHX_FIBER=3, LX_SX_FIBER=4 (It is obsoleted for Chassis Product)
INT snChasSpeedLeds	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.15	INTEGER	read-only	A bit array that contains the value of the front panel media LEDs. This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Speed LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning --------- ------- 0 10 MBit 1 100 MBit The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 ---------
INT snChasEnableFanTrap	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.16	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate fan failure traps.
STR snChasIdNumber	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.17	DisplayString	read-write	An administratively-assigned chassis identity number, used by inventory control.
INT snChasActualTemperature	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.18	INTEGER	read-only	Temperature of the chassis. Each unit is 0.5 degrees Celcius. Only management module built with temperature sensor hardware is applicable. For those non-applicable management module, it returns no-such-name.
INT snChasWarningTemperature	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.19	INTEGER	read-write	Actual temperature higher than this threshold value will trigger the switch to send a temperature warning trap. Each unit is 0.5 degrees Celcius. Only management module built with temperature sensor hardware is applicable. For those non-applicable management module, it returns no-such-name.
INT snChasShutdownTemperature	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.20	INTEGER	read-write	Actual temperature higher than this threshold value will shutdown a partial of the switch hardware to cool down the system. Each unit is 0.5 degrees Celcius. Only management module built with temperature sensor hardware is applicable. For those non-applicable management module, it returns no-such-name.
INT snChasEnableTempWarnTrap	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.21	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate temperature warning traps.
INT snChasFlashCard	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.22	INTEGER	read-only	A bit array that contains the value of the flash card status. This is a packed bit string. The status of each flash card is encoded into one bit. bit value meaning --------- ------- 0 flash card absent. 1 flash card present. There are up to two flash cards in this release. This object is valid if M4 management module is present. The following shows the meaning of each bit: (bit 0 is the least significant bit). bit position meaning ------------ ------- 2-31 reserved 1 flash card 2 status 0 flash card 1 status
INT snChasFlashCardLeds	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.23	INTEGER	read-only	A bit array that contains the value of the flash card LEDs. This is a packed bit string; each LED is encoded into 1 bit for each flash card. bit value meaning -------- --------- 0 off 1 on
INT snChasNumSlots	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.24	INTEGER	read-only	Number of slots of the chassis.
INT snChasArchitectureType	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.25	INTEGER	read-only	Architecture type.
INT snChasProductType	1.3.6.1.4.1.11.2.3.7.11.12.1.1.1.26	INTEGER	read-only	Product type.
snChasPwr	1.3.6.1.4.1.11.2.3.7.11.12.1.1.2
snChasPwrSupplyTable	1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1		not-accessible	A table of each power supply information. Only installed power supply appears in a table row.
snChasPwrSupplyEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1		not-accessible	A row in the power supply table.
INT snChasPwrSupplyIndex	1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1.1	INTEGER	read-only	The index to power supply table.
STR snChasPwrSupplyDescription	1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1.2	DisplayString	read-only	The power supply description string.
INT snChasPwrSupplyOperStatus	1.3.6.1.4.1.11.2.3.7.11.12.1.1.2.1.1.3	INTEGER	read-only	The power supply operation status.
snChasFan	1.3.6.1.4.1.11.2.3.7.11.12.1.1.3
snChasFanTable	1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1		not-accessible	A table of each fan information. Only installed fan appears in a table row.
snChasFanEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1		not-accessible	A row in the fan table.
INT snChasFanIndex	1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1.1	INTEGER	read-only	The index to fan table.
STR snChasFanDescription	1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1.2	DisplayString	read-only	The fan description string.
INT snChasFanOperStatus	1.3.6.1.4.1.11.2.3.7.11.12.1.1.3.1.1.3	INTEGER	read-only	The fan operation status.
snAgentGbl	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1
INT snAgReload	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.1	INTEGER	read-write	Action object to reboot the agent. The following values can only be read: other(1).....agent in unknown or other state running(2)...agent running The following value can be written: reset(3).....do a hard reset The agent will return a response before the action occurs.
INT snAgEraseNVRAM	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.2	INTEGER	read-write	Action object to erase NVRAM of the agent. The following values can only be read: normal(1) error(2)... operation failed or bad flash erasing(4)...agent is erasing NVRAM flash The following value can be written: erase(3).....do erase The agent will return a response even before the erase is done. And the read value will be erasing until erase is done. And the erase request will be rejected until error or normal.
INT snAgWriteNVRAM	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.3	INTEGER	read-write	Action object to save all configuration info to NVRAM of the agent. The following values can only be read: normal(1) error(2)... operation failed or bad flash writing(4)...agent is writing NVRAM flash The following value can be written: write(3).....do write The agent will return a response even before the write is done. And the read value will be writing until write is done. And the write request will be rejected until error or normal.
INT snAgConfigFromNVRAM	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.4	INTEGER	not-accessible	Action object to config the switch from NVRAM of the agent. The following values can only be read: normal(1) error(2)... operation failed or bad flash configing(4)...configing from NVRAM flash is in process. The following value can be written: config(3).....do config The agent will return a response after config is done.
IP snAgTftpServerIp	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.5	IpAddress	read-write	The tftp server address, this will be used for both download/upload image file and config file.
STR snAgImgFname	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.6	DisplayString	read-write	Name of the image file including path currently associated with the system. When the object is not used, the value is a zero length string.
INT snAgImgLoad	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.7	INTEGER	read-write	Action object to down/up load a new image to the agent. The following values: Error values: from normal(1) to operationError(17) and tftpWrongFileType(23). loading(18) .. operation is in process. The following values are used for set : uploadPrimary(19)..upload the Primary image from flash to tftp server. downloadPrimary(20)..download the Primary image from tftp server to flash. uploadSecondary(21)..upload the Secondary image from flash to tftp server. downloadSecondary(22)..download the Secondary image from tftp server to flash. The image filename is defined in snAgImgFname. The tftp server address is defined in snAgTftpServerIp. Atomic set of snAgImgLoad, snAgImgFname and snAgTftpServerIp is required to allow down/up load to happen. And the write request will be rejected during loading until error or normal.
STR snAgCfgFname	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.8	DisplayString	read-write	Name of the config file(s) including path currently associated with the system. Some agents in special situations may support a value which contains multiple file names instead of a single file name. Multiple names are specified as a list of file names separated by semicolons (;). When the object is not used, the value is a zero length string.
INT snAgCfgLoad	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.9	INTEGER	read-write	Action object to down/up load a config image to the agent. The following values can be read : Error values: from normal(1) to operationError(17) and tftpWrongFileType(29). loading(18) .. operation is in process. The following value can be used to set: uploadFromFlashToServer(20)..upload the config from flash to tftp server. downloadToFlashFromServer(21)..download the config to flash from tftp server. uploadFromDramToServer(22)..upload the config from DRAM to tftp server. downloadToDramFromServer(23)..download the config to DRAM from tftp server. The following value can be used to set: uploadFromFlashToNMS(24)..upload the config from flash to NMS. downloadToFlashFromNMS(25)..download the config to flash from NMS. uploadFromDramToNMS(26)..upload the config from DRAM to NMS. downloadToDramFromNMS(27)..download the config to DRAM from NMS. The config filename is defined in snAgCfgFname. The tftp server address is defined in snAgTftpServerIp. Atomic set of snAgCfgLoad, snAgCfgFname and snAgTftpServerIp is required to allow down/up load to happen. And the write request will be rejected during loading until error or normal. For those NMS commands from (24) to (27), The snAgCfgEosTable MIB must be sent along in one PDU. A seperate write memory cli or set snAgWriteNVRAM is required to save the config to NVRAM.
IP snAgDefGwayIp	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.10	IpAddress	read-write	The default gateway (router) address.
STR snAgImgVer	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.11	DisplayString	read-only	The version of the running software in the form 'major.minor.maintenance[letters]'.
STR snAgFlashImgVer	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.12	DisplayString	read-only	The version of the software image saved in local storage such as flash memory in the form 'major.minor.maintenance[letters]'. If not known or not available, then the value is a zero length string.
IP snAgGblIfIpAddr	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.13	IpAddress	read-write	The interface ip address.
IP snAgGblIfIpMask	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.14	IpAddress	read-write	The interface ip address mask.
STR snAgGblPassword	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.15	DisplayString	read-write	System Security Access Password and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero string.
INT snAgTrpRcvrCurEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.16	INTEGER	read-only	The current total entries of the Trap Receiver Table are created.
INT snAgGblDataRetrieveMode	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.19	INTEGER	read-write	By default, this mode is set to nextbootCfg(0). The VLAN Table and Port-STP Table data will be retrieved according to this mode. nextbootCfg(0).........the nextboot configuration data are retrieved operationalData(1)..........the current running data are retrieved
OCT snAgSystemLog	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.20	OCTET STRING	read-write	The system log object to indicate whether any Network Management Station(NMS) has login. The first byte of the octet string is the value decribed below and followed by 4 bytes of secret code. login(1)..... a value for a NMS to login. heartbeat(2)... a value for the login NMS periodically to checkin; Otherwise, the Agent will automatically set this object to logout(3) after a timeout period. logout(3).... a value for a NMS to logout. changePassword(4).... a value for the login NMS to change password, only if snAgGblPasswordChangeMode was configured to 'anyMgmtEntity'. changeReadOnlyCommunity(5).... a value for the login NMS to change the read-only community string, only if snAgGblPasswordChangeMode was configured to 'anyMgmtEntity'. changeReadWriteCommunity(6).... a value for the login NMS to change the read-write community string, only if snAgGblPasswordChangeMode was configured to 'anyMgmtEntity'.
INT snAgGblEnableColdStartTrap	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.21	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate cold start traps.
INT snAgGblEnableLinkUpTrap	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.22	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate link up traps.
INT snAgGblEnableLinkDownTrap	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.23	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate link down traps.
INT snAgGblPasswordChangeMode	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.24	INTEGER	read-only	Specify which management entity is allowed to change the password. 'anyMgmtEntity' management entities are SNMP management station, console command line interface, and telnet command line interface. For security reason, this object can only be modified by console command line interface or telnet command line interface. The default value is 'consoleAndTelnet', of which both console and telnet command line interfaces are allowed to change the password.
STR snAgGblReadOnlyCommunity	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.25	DisplayString	read-write	SNMP read community string and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero length string.
STR snAgGblReadWriteCommunity	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.26	DisplayString	read-write	SNMP read-write community string and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero length string.
INT snAgGblCurrentSecurityLevel	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.27	INTEGER	read-only	This represnts the current log-in security level. Each level of security requires a password to permit user for different system configurations.
INT snAgGblSecurityLevelSet	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.28	INTEGER	read-write	This shows which the security level password to be set.
INT snAgGblLevelPasswordsMask	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.29	INTEGER	read-only	This shows the bitmap of level passwords which successfully assigned to the system.
INT snAgGblQueueOverflow	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.30	INTEGER	read-only	false - The device queues are not overflow. true - The device queues are overflow.
INT snAgGblBufferShortage	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.31	INTEGER	read-only	false - The device buffers are adequate. true - The device buffers are in shortage.
INT snAgGblDmaFailure	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.32	INTEGER	read-only	false - The device DMAs are in good condition. true - One of the DMAs in the device fails.
INT snAgGblResourceLowWarning	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.33	INTEGER	read-only	false - No, the device does not have resource-low-warning. true - Yes, the device does have resource-low-warning.
INT snAgGblExcessiveErrorWarning	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.34	INTEGER	read-only	false - No, the device does not have any excessive collision, FCS errors, alignment warning etc. true - Yes, the device does have.
GAU snAgGblCpuUtilData	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.35	Gauge	read-only	The statistics collection of utilization of the CPU in the device.
INT snAgGblCpuUtilCollect	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.36	INTEGER	read-write	enable(1) - The beginning of statistics collection of utilization of the CPU in the device. disable(0) - The end of statistics collection of utilization of the CPU in the device.
INT snAgGblTelnetTimeout	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.37	INTEGER	read-write	Telnet session idling timeout value. Writing value 0 to this object never timeouts any telnet sessions. Each value unit is one minute.
INT snAgGblEnableWebMgmt	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.38	INTEGER	read-write	Enable/disable web management.
INT snAgGblSecurityLevelBinding	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.39	INTEGER	read-only	This represnts the binding of a given password to which security level. A value of 255 indicates an invalid binding.
INT snAgGblEnableSLB	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.40	INTEGER	read-only	Enable/disable Server Load Balancing.
OCT snAgSoftwareFeature	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.41	OCTET STRING	read-only	A bit string representing the software feature of the running switch/router image. These features were conditional compiled to different product images. For each bit, exist feature has a value of 1, but non-exist feature has a value of 0. octet 0, bit 0 - RMON octet 0, bit 1 - ipx switching octet 0, bit 2 - server load balancing octet 0, bit 3 - layer 3 filter in switch octet 0, bit 4 - ipx routing octet 0, bit 5 - appletalk routing octet 0, bit 6 - ip multicast routing octet 0, bit 7 - local access control octet 1, bit 0 - BGP routing octet 1, bit 1 - loopback interface octet 1, bit 2 - BigIron multi-management module octet 1, bit 3 - BigIron SYSIF II octet 1, bit 4 - BigIron POS support octet 1, bit 5 - appletalk cable vlan octet 1, bit 6 - 64 subnet octet 1, bit 7 - multi-slot trunk octet 2, bit 0 - TACACS octet 2, bit 1 - Gigabit Ethernet port auto-negotiation mode octet 2, bit 2 - FSRP octet 2, bit 3 - Exodus requested OSPF enhancement octet 2, bit 4 - OSPF NSSA octet 2, bit 5 - POS octet 2, bit 6 - QOS octet 2, bit 7 - Single Span octet 3, bit 0 - Fast Span octet 3, bit 1 - Base L3 octet 3, bit 2 - static log buffer Bit 0 is the least significant bit of an octet, and bit 7 is the most significant bit of an octet.
INT snAgGblEnableModuleInsertedTrap	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.42	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate hardware module inserted to chassis traps.
INT snAgGblEnableModuleRemovedTrap	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.43	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate hardware module removed from chassis traps.
STR snAgGblTrapMessage	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.44	DisplayString	read-only	A generic trap message string.
INT snAgGblEnableTelnetServer	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.45	INTEGER	read-write	Enable or disable telnet server in device.
STR snAgGblTelnetPassword	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.46	DisplayString	read-write	Telnet Access Password and this is only allowed to use for setting but not for reading. An SNMP-Get will get an zero string.
STR snAgBuildDate	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.47	DisplayString	read-only	The date of the built software.
STR snAgBuildtime	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.48	DisplayString	read-only	The time of the built software.
STR snAgBuildVer	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.49	DisplayString	read-only	The version of the built software in the form 'major.minor.maintenance[letters]'.
GAU snAgGblCpuUtil1SecAvg	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.50	Gauge	read-only	The statistics collection of 1 second CPU utilization.
GAU snAgGblCpuUtil5SecAvg	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.51	Gauge	read-only	The statistics collection of 5 second CPU utilization.
GAU snAgGblCpuUtil1MinAvg	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.52	Gauge	read-only	The statistics collection of 1 minute CPU utilization.
GAU snAgGblDynMemUtil	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.53	Gauge	read-only	The system dynamic memory utilization, in unit of percentage.
INT snAgGblDynMemTotal	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.54	INTEGER	read-only	The total amount of system dynamic memory, in number of bytes.
INT snAgGblDynMemFree	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.55	INTEGER	read-only	The free amount of system dynamic memory, in number of bytes.
INT snAgImgLoadSPModuleType	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.56	INTEGER	read-write	The switch processor module type of which that receives the downloaded image.
INT snAgImgLoadSPModuleNumber	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.57	INTEGER	read-write	The slot numner of a switch processor module that receives the downloaded image. Setting value 0 applies to all SP modules.
INT snAgTrapHoldTime	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.58	INTEGER	read-write	The time in seconds for which traps will be witheld during system initialization.
NUM snAgSFlowSourceInterface	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.59	InterfaceIndex	read-write	Use the ifIndex value here to specify the source interface to be used for sFlow packets. The interface should have IP address configured on it. Value of 0 indicates that source interface has not been configured for sFlow. Port 65534 is used to specify a null port.
INT snAgGblTelnetLoginTimeout	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.60	INTEGER	read-write	Telnet session login timeout value in minutes. Default is 1 minute.
STR snAgGblBannerExec	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.61	DisplayString	read-write	EXEC process creation banner. Insert newlines using '\n' within the string.
STR snAgGblBannerIncoming	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.62	DisplayString	read-write	Incoming terminal line banner. Insert newlines using '\n' within the string.
STR snAgGblBannerMotd	1.3.6.1.4.1.11.2.3.7.11.12.1.2.1.63	DisplayString	read-write	Message-of-the-day banner. Insert newlines using '\n' within the string.
snAgentBrd	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2
snAgentBrdTable	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1		not-accessible	A table of each physical board information.
snAgentBrdEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1		not-accessible	A row in the Agent Board table.
INT snAgentBrdIndex	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.1	INTEGER	read-only	The index to the Agent Interface Table.
STR snAgentBrdMainBrdDescription	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.2	DisplayString	read-only	The main board description string.
OCT snAgentBrdMainBrdId	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.3	OCTET STRING	read-only	The main board identifier, which can uniquely identify a board type. It is an encoded octet string with the following meaning: octet 0 - octet string format version, which identifies the format of this string. If format version octet has the value 2, the octets after the version octet have the following meaning: octet 1 - product type: BI_WG 0x57 BI_BB 0x42 BI_NI 0x4E octet 2 - module type: MASTER_FIBER_8G 0x0 MASTER_FIBER_4G 0x1 MASTER_FIBER_2G 0x12 MASTER_FIBER_0G 0x14 MASTER_COPPER_16 0x2 MASTER_COPPER_8G 0x6 MASTER_COPPER_12_2 0x9 SLAVE_FIBER_8G 0x8 SLAVE_FIBER_4G 0x3 SLAVE_FIBER_2G 0x17 SLAVE_COPPER_8G 0xE SLAVE_COPPER_2G 0x18 SLAVE_COPPER_16_2 0xF SLAVE_COPPER_20 0xA SLAVE_COPPER_24 0xA SLAVE_100FX_8 0xD SLAVE_100FX_16 0xC SLAVE_100FX_24 0x13 STACK_FIBER_8G 0x10 STACK_COPPER_8G 0x11 POS_622M 0x15 POS_155M 0x16 octet 3 - processor type, PVR_M603=3, PVR_M604=4, PVR_M603E=6, PVR_M603EV=7, PVR_M604E=9 octet 4 to octet 5 - processor speed in MHz octet 6 - MAC type: MAC_SEEQ_10_100=1, MAC_DEC_10_100=2, MAC_SEEQ_1000=5, MAC_GMAC_1000=6, MAC_VLSI_1000=9 octet 7 - PHY type, PHY_NONE=0, PHY_QSI=1, PHY_ICS=3, PHY_NATIONAL=4, PHY_LEVEL1=6, PHY_LEVEL16=7, PHY_LEVEL24=8 octet 8 - port type, COPPER=0, FIBER=1 octet 9 - fiber port type, NONFIBER=0, SX_FIBER=1, LX_FIBER=2, LHX_FIBER=3 octet 10 to octet 13 - DRAM size in KBytes octet 14 to octet 17 - boot flash size in KBytes octet 18 to octet 21 - code flash size in KBytes octet 22 to octet 27 - serial number. octet 28 - chassis backplane type. chassis4000 = 0x00 chassis8000 = 0x04 Turbo8 = 0x07 (stack2) FastIron2 = 0x06 (stack1)
INT snAgentBrdMainPortTotal	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.4	INTEGER	read-only	The total number of ports for the main board.
STR snAgentBrdExpBrdDescription	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.5	DisplayString	read-only	The expansion board description string. Expansion board are those boards attaching on the main board.
OCT snAgentBrdExpBrdId	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.6	OCTET STRING	read-only	The expansion board identifier. Expansion board are those boards attaching on the main board. It is an encoded octet string with the following meaning: octet 0 - octet string format version, which identifies the format of this string. If format version octet has the value 1, the octets after the version octet have the following meaning: octet 1 - expansion board type, HUNDRED_MEG_1PORT=1, HUNDRED_MEG_2PORT=2, HUNDRED_MEG_1PORT_COPPER=3, HUNDRED_MEG_2PORT_COPPER=4, HUNDRED_MEG_2PORT_LX=5, GIGA_1PORT=8, GIGA_2PORT=9 octet 2 - fiber port type, NONFIBER=0, SX_FIBER=1, LX_FIBER=2, LHX_FIBER=3, LX_SX_FIBER=4
INT snAgentBrdExpPortTotal	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.7	INTEGER	read-only	The total number of ports for the expansion board.
INT snAgentBrdStatusLeds	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.8	INTEGER	read-only	A bit array that contains the value of the front panel status LEDs. This is a bit-map; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 32 that means 32 Ports Status LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (Link off) 1 on (Link on) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
INT snAgentBrdTrafficLeds	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.9	INTEGER	read-only	A bit array that contains the value of the front panel traffic LEDs. This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Traffic LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (no traffic) 1 on (traffic) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
INT snAgentBrdMediaLeds	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.10	INTEGER	read-only	A bit array that contains the value of the front panel media LEDs. This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Media LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning --------- ------- 0 half duplex 1 full duplex The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 ---------
INT snAgentBrdSpeedLeds	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.11	INTEGER	read-only	A bit array that contains the value of the front panel media LEDs. This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Speed LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning --------- ------- 0 10 MBit 1 100 MBit The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 ---------
INT snAgentBrdModuleStatus	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.12	INTEGER	read-only	By default, this mode is set to notActivated(0). moduleEmpty(0) ......... The slot of the chassis is empty. moduleGoingDown(2) ..... The module is going down. moduleRejected(3) ...... The module is being rejected due to wrong configuration. moduleBad(4) ........... The module Hardware is bad. moduleComingUp(9) ...... The module is in power-up cycle. moduleRunning(10) ....... The module is running.
INT snAgentBrdRedundantStatus	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.13	INTEGER	read-only	The redundant status of a module. Non-management module always returns other(1). Management module returns the rest of the states.
INT snAgentBrdAlarmLeds	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.14	INTEGER	read-only	A bit array that contains the value of the front panel media LEDs (for POS Module Only). This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Speed LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning --------- ------- 0 no alarm 1 alarm The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 ---------
INT snAgentBrdTxTrafficLeds	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.15	INTEGER	read-only	A bit array that contains the value of the front panel transmit traffic LEDs (for POS Module Only). This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Transmit Traffic LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (no transmit traffic) 1 on (transmit traffic) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
INT snAgentBrdRxTrafficLeds	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.16	INTEGER	read-only	A bit array that contains the value of the front panel receive traffic LEDs (for POS Module Only). This is a packed bit string; each LED is encoded into 1 bit for each switch port. The maximum number of ports in one chassis is 24 that means 24 Ports Receive Traffic LEDs. The expansion port number always begins from the last main port number. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (no receive traffic) 1 on (receive traffic) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
OCT snAgentBrdStatusLedString	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.17	OCTET STRING	read-only	A bit array that contains the value of the front panel status LEDs. This is a bit-map; each LED is encoded into 1 bit for each switch port. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (Link off) 1 on (Link on) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
OCT snAgentBrdTrafficLedString	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.18	OCTET STRING	read-only	A bit array that contains the value of the front panel traffic LEDs. This is a packed bit string; each LED is encoded into 1 bit for each switch port. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (no traffic) 1 on (traffic) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
OCT snAgentBrdMediaLedString	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.19	OCTET STRING	read-only	A bit array that contains the value of the front panel media LEDs. This is a packed bit string; each LED is encoded into 1 bit for each switch port. The following shows the meaning of each bit for each switch port: bit value meaning --------- ------- 0 half duplex 1 full duplex The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 ---------
OCT snAgentBrdSpeedLedString	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.20	OCTET STRING	read-only	A bit array that contains the value of the front panel media LEDs. This is a packed bit string; each LED is encoded into 1 bit for each switch port. The following shows the meaning of each bit for each switch port: bit value meaning --------- ------- 0 10 MBit 1 100 MBit The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 ---------
OCT snAgentBrdAlarmLedString	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.21	OCTET STRING	read-only	A bit array that contains the value of the front panel media LEDs (for POS Module Only). This is a packed bit string; each LED is encoded into 1 bit for each switch port. The following shows the meaning of each bit for each switch port: bit value meaning --------- ------- 0 no alarm 1 alarm The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 ---------
OCT snAgentBrdTxTrafficLedString	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.22	OCTET STRING	read-only	A bit array that contains the value of the front panel transmit traffic LEDs (for POS Module Only). This is a packed bit string; each LED is encoded into 1 bit for each switch port. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (no transmit traffic) 1 on (transmit traffic) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
OCT snAgentBrdRxTrafficLedString	1.3.6.1.4.1.11.2.3.7.11.12.1.2.2.1.1.23	OCTET STRING	read-only	A bit array that contains the value of the front panel receive traffic LEDs (for POS Module Only). This is a packed bit string; each LED is encoded into 1 bit for each switch port. The following shows the meaning of each bit for each switch port: bit value meaning -------- --------- 0 off (no receive traffic) 1 on (receive traffic) The bitmap of LEDs are as following: (Port1) (Port4) (Port8) Bit (Bit0) (Bit3) (Bit7) Byte 1: LED1 LED2 LED3 LED4 LED5 LED6 LED7 LED8 Byte 2: LED9 LED10 LED11 LED12 LED13 LED14 LED15 LED16 Byte 3: LED17 LED18 LED19 LED20 LED21 LED22 LED23 LED24 --------
snAgentTrp	1.3.6.1.4.1.11.2.3.7.11.12.1.2.3
snAgTrpRcvrTable	1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1		not-accessible	A table of managers which to send traps.
snAgTrpRcvrEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1		not-accessible	A row in the trap receiver table. The column snAgTrpRcvrStatus is used to create and delete rows in the table. Creation requires a SET PDU with objects snAgTrpRcvrIndex, snAgTrpRcvrIpAddr, snAgTrpRcvrComm and snAgTrpRcvrStatus.
INT snAgTrpRcvrIndex	1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.1	INTEGER	read-only	The index to the Trap Receiver Table.
IP snAgTrpRcvrIpAddr	1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.2	IpAddress	read-write	The ip address for SNMP manager that is to receive the trap.
OCT snAgTrpRcvrComm	1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.3	OCTET STRING	read-write	Community string to use.
INT snAgTrpRcvrStatus	1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.4	INTEGER	read-write	This object is used to create and delete rows in the table and control if they are used. The values that can be written are: ignore(5)...don't use this entry to send traps to at this time delete(3)...deletes the row create(4)...creates a new row If the row exists, then a SET with value of create(5) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: other(1)....some other case valid(2)....the row exists and is valid ignore(5)...don't use this entry to send traps to at this time
INT snAgTrpRcvrUDPPort	1.3.6.1.4.1.11.2.3.7.11.12.1.2.3.1.1.5	INTEGER	read-write	UDP port number of the trap receiver.
snAgentBoot	1.3.6.1.4.1.11.2.3.7.11.12.1.2.4
snAgBootSeqTable	1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1		not-accessible	A table of image load sequnce instructions to the boot code. Boot code will start from instruction of the first valid entry to load the image. If failed, it will use the second valid entry and so on, until a succesful load has completed. Each entry must have an unique instruction, duplicate instructions will be rejected.
snAgBootSeqEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1		not-accessible	A row in the boot sequence table.
INT snAgBootSeqIndex	1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.1	INTEGER	read-only	The index to the boot sequence table.
INT snAgBootSeqInstruction	1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.2	INTEGER	read-write	The instruction for the boot code.
IP snAgBootSeqIpAddr	1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.3	IpAddress	read-write	The ip address of the TFTP server if snAgBootSeqInstruction was set to 'fromTftpServer'; otherwise, this object is not used in any other boot instruction.
STR snAgBootSeqFilename	1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.4	DisplayString	read-write	The image filename on the TFTP server if snAgBootSeqInstruction was set to 'fromTftpServer'; otherwise, this object is not used in any other boot instruction.
INT snAgBootSeqRowStatus	1.3.6.1.4.1.11.2.3.7.11.12.1.2.4.1.1.5	INTEGER	read-write	To create or delete a boot sequence table entry.
snAgCfgEos	1.3.6.1.4.1.11.2.3.7.11.12.1.2.5
snAgCfgEosTable	1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1		not-accessible	This table represents the fragmented Configuration File data packet with checksum include in each rows of this table. A SNMP-SET represents configuration file download, and a SNMP-GET represents configuration file upload. This action is only if the SNMP-SET of snAgCfgLoad command is sent along with this table consecutively. The applicable snAgCfgLoad command value is as followings: uploadFromFlashToNMS(23), downloadToFlashFromNMS(24), uploadFromDramToNMS(25), downloadToDramFromNMS(26).
snAgCfgEosEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1		not-accessible	An EOS row in the table of encoded octet strings for table snAgCfgEosTable.
INT snAgCfgEosIndex	1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1.1	INTEGER	read-only	Each VLAN EOS Buffer Identifier have a multiple VLAN table entries.
OCT snAgCfgEosPacket	1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1.2	OCTET STRING	read-write	An encoded octet string. On reads it contains an integral number of configuration file data packets. The size of each encoded octet string is less than or equal to 1400 bytes.
INT snAgCfgEosChkSum	1.3.6.1.4.1.11.2.3.7.11.12.1.2.5.1.1.3	INTEGER	read-write	A checksum of each configuration file data packet.
snAgentLog	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6
snAgSysLogGbl	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1
INT snAgSysLogGblEnable	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.1	INTEGER	read-write	Enable/disable system logging.
INT snAgSysLogGblBufferSize	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.2	INTEGER	read-write	The number of dynamic system logging entries.
INT snAgSysLogGblClear	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.3	INTEGER	read-write	Clear dynamic and/or static system logging buffers.
INT snAgSysLogGblCriticalLevel	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.4	INTEGER	read-write	Filter events going to the logging buffer. This is a packed bit string object of which each bit has the following meaning: (bit 0 is the least significant bit). bit position meaning ------------ ------- 8-31 reserved 7 Warning (warning conditions) 6 Notification (normal but significant conditions) 5 Informational (informational messages) 4 Error (error conditions) 3 Emergency (system is unusable) 2 Debugging (debugging messages) 1 Critical (critical conditions) 0 Alert (immediate action needed) Setting a critical level bit to 1 makes the logging buffer accept the corresponding event. Resetting a critical level bit to 0 makes the logging buffer reject the corresponding event.
CTR snAgSysLogGblLoggedCount	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.5	Counter	read-only	The number events logged in the system logging buffer.
CTR snAgSysLogGblDroppedCount	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.6	Counter	read-only	The number of events dropped.
CTR snAgSysLogGblFlushedCount	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.7	Counter	read-only	The number of times that the system logging buffer was cleared.
CTR snAgSysLogGblOverrunCount	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.8	Counter	read-only	The number of times that the system logging buffer was wrapped around.
IP snAgSysLogGblServer	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.9	IpAddress	read-write	IP address of syslog server.
INT snAgSysLogGblFacility	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.1.10	INTEGER	read-write	Facility code.
snAgSysLogBufferTable	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2		not-accessible	Dynamic system logging buffer table.
snAgSysLogBufferEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1		not-accessible	A row in the dynamic system logging buffer table.
INT snAgSysLogBufferIndex	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.1	INTEGER	read-only	The index to the dynamic system logging buffer table.
TIK snAgSysLogBufferTimeStamp	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.2	TimeTicks	read-only	A time stamp when the event is logged.
INT snAgSysLogBufferCriticalLevel	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.3	INTEGER	read-only	The critical level of this event.
STR snAgSysLogBufferMessage	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.4	DisplayString	read-only	The system logging message.
STR snAgSysLogBufferCalTimeStamp	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.2.1.5	DisplayString	read-only	A time stamp when the event is logged. This object returns a NULL terminated time stamp string if the system calendar time was set. It returns a zero length string if the system calendar time was not set.
snAgStaticSysLogBufferTable	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3		not-accessible	Static system logging buffer table.
snAgStaticSysLogBufferEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1		not-accessible	A row in the static system logging buffer table.
INT snAgStaticSysLogBufferIndex	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.1	INTEGER	read-only	The index to the static system logging buffer table.
TIK snAgStaticSysLogBufferTimeStamp	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.2	TimeTicks	read-only	A time stamp when the event is logged.
INT snAgStaticSysLogBufferCriticalLevel	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.3	INTEGER	read-only	The critical level of this event.
STR snAgStaticSysLogBufferMessage	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.4	DisplayString	read-only	The system logging message.
STR snAgStaticSysLogBufferCalTimeStamp	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.3.1.5	DisplayString	read-only	A time stamp when the event is logged. This object returns a NULL terminated time stamp string if the system calendar time was set. It returns a zero length string if the system calendar time was not set.
snAgSysLogServerTable	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.4		not-accessible	System Log Server table.
snAgSysLogServerEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.4.1		not-accessible	A row in the SysLog Server table.
IP snAgSysLogServerIP	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.4.1.1	IpAddress	read-write	IP address of syslog server.
INT snAgSysLogServerUDPPort	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.4.1.2	INTEGER	read-write	UDP port number of syslog server.
INT snAgSysLogServerRowStatus	1.3.6.1.4.1.11.2.3.7.11.12.1.2.6.4.1.3	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: other(1)....some other case valid(2)....the row exists and is valid
snAgentSysParaConfig	1.3.6.1.4.1.11.2.3.7.11.12.1.2.7
snAgentSysParaConfigTable	1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1		not-accessible	A table of Agent of each board.
snAgentSysParaConfigEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1		not-accessible	A row in the Agent System Parameters Configuation table.
INT snAgentSysParaConfigIndex	1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.1	INTEGER	read-only	The index to the Agent System Parameters Configuation Table.
STR snAgentSysParaConfigDescription	1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.2	DisplayString	read-only	The main board description string.
INT snAgentSysParaConfigMin	1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.3	INTEGER	read-only	The minimum value of this Agent System Parameter.
INT snAgentSysParaConfigMax	1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.4	INTEGER	read-only	The maximum value of this Agent System Parameter.
INT snAgentSysParaConfigDefault	1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.5	INTEGER	read-only	The default value of this Agent System Parameter.
INT snAgentSysParaConfigCurrent	1.3.6.1.4.1.11.2.3.7.11.12.1.2.7.1.1.6	INTEGER	read-write	The current configurated value of this Agent System Parameter.
snAgentConfigModule	1.3.6.1.4.1.11.2.3.7.11.12.1.2.8
snAgentConfigModuleTable	1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1		not-accessible	A table of each configured module information.
snAgentConfigModuleEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1		not-accessible	A row in the Agent Configured Module table.
INT snAgentConfigModuleIndex	1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.1	INTEGER	read-only	The index to the Agent Configured Module Table.
INT snAgentConfigModuleType	1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.2	INTEGER	read-write	The Configured Module Type.
INT snAgentConfigModuleRowStatus	1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.3	INTEGER	read-write	To create or delete a configured module table entry.
STR snAgentConfigModuleDescription	1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.4	DisplayString	read-only	A description of the configured module.
STR snAgentConfigModuleOperStatus	1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.5	DisplayString	read-only	Module operational status. Zero length string indicates that physical module has not been inserted to the chassis.
STR snAgentConfigModuleSerialNumber	1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.6	DisplayString	read-only	Module serial number. Zero length string indicates that module serial number EEPROM has not been programmed or the module does not support serial number EEPROM.
INT snAgentConfigModuleNumberOfPorts	1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.7	INTEGER	read-only	The number of ports of module.
INT snAgentConfigModuleMgmtModuleType	1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.8	INTEGER	read-only	Management module type.
INT snAgentConfigModuleNumberOfCpus	1.3.6.1.4.1.11.2.3.7.11.12.1.2.8.1.1.9	INTEGER	read-only	The number of module CPUs.
snAgentUser	1.3.6.1.4.1.11.2.3.7.11.12.1.2.9
snAgentUserGbl	1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.1
INT snAgentUserMaxAccnt	1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.1.1	INTEGER	read-only	Maximum number of user account entries can be configured.
snAgentUserAccntTable	1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2		not-accessible	A table of user account information.
snAgentUserAccntEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1		not-accessible	A row in the Agent User table.
STR snAgentUserAccntName	1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.1	DisplayString	read-only	The user name.
STR snAgentUserAccntPassword	1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.2	DisplayString	read-write	The user password.
INT snAgentUserAccntEncryptCode	1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.3	INTEGER	read-write	The password encryption method code.
INT snAgentUserAccntPrivilege	1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.4	INTEGER	read-write	The user privilege.
INT snAgentUserAccntRowStatus	1.3.6.1.4.1.11.2.3.7.11.12.1.2.9.2.1.5	INTEGER	read-write	To create or delete a user account table entry.
snAgentRedundant	1.3.6.1.4.1.11.2.3.7.11.12.1.2.10
snAgentRedunGbl	1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1
INT snAgentRedunActiveMgmtMod	1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.1	INTEGER	read-write	Slot number of the active management module. Setting this object does not take effect immediately. Saving configuration data to flash storage and reboot the system are required to take effect. Setting a value of 0 requests the system to auto-select an active management module after power up.
INT snAgentRedunSyncConfig	1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.2	INTEGER	read-write	Frequency of the backup management module copying the configuration data from the active management module. Each unit is 1 second. Setting a value 0 will disable the synchronization copy. Setting a negative value will initiate the synchronization copy once immediately.
INT snAgentRedunBkupCopyBootCode	1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.3	INTEGER	read-write	If enabled(1), the backup management module copies the boot code from the active management module to its boot code flash storage after power up, and whenever the active management module's boot code is updated. The backup management module does not copy if both boot codes were identical.
INT snAgentEnableMgmtModRedunStateChangeTrap	1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.4	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate management module redundancy state change traps.
INT snAgentRedunBkupBootLoad	1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.5	INTEGER	read-write	Action object to down load a new boot code from boot flash storage of the active management module to the backup management module. The following are returned values from get operation: normal(1)............no operation operationError(17)...error codes The following are input values from set operation: downloadBackup(20)...download the boot code from the active management module to the backup management module Any set operation is rejected during loading until error or normal state is reached.
INT snAgentRedunSwitchOver	1.3.6.1.4.1.11.2.3.7.11.12.1.2.10.1.6	INTEGER	read-write	To force a switch-over from standby to active state if the backup management module exists in a chassis.
snAgentCpu	1.3.6.1.4.1.11.2.3.7.11.12.1.2.11
snAgentCpuUtilTable	1.3.6.1.4.1.11.2.3.7.11.12.1.2.11.1		not-accessible	Table to list utilization for all CPUs in the device.
snAgentCpuUtilEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.2.11.1.1		not-accessible	A row in the CPU utilization table.
INT snAgentCpuUtilSlotNum	1.3.6.1.4.1.11.2.3.7.11.12.1.2.11.1.1.1	INTEGER	read-only	The slot number of module which contains the cpu.
INT snAgentCpuUtilCpuId	1.3.6.1.4.1.11.2.3.7.11.12.1.2.11.1.1.2	INTEGER	read-only	The id of cpu. For non-VM1/WSM management module, there is one CPU. For VM1/WSM there's one management CPU and three slave CPUs. The management CPU could be turned off. For POS and ATM there's no management CPU but two slave CPUs. Id for management cpu is 1. Value of 2 or greater are for slave CPUs.
INT snAgentCpuUtilInterval	1.3.6.1.4.1.11.2.3.7.11.12.1.2.11.1.1.3	INTEGER	read-only	The value, in seconds, for this utilization. For both management and slave CPU, we display utilization for 1 sec, 5 sec, 60 sec and 300 sec interval.
GAU snAgentCpuUtilValue	1.3.6.1.4.1.11.2.3.7.11.12.1.2.11.1.1.4	Gauge	read-only	The statistical CPU utilization in units of one-hundredth of a percent.
snAgentHw	1.3.6.1.4.1.11.2.3.7.11.12.1.2.12
snAgentHwICBMCounterTable	1.3.6.1.4.1.11.2.3.7.11.12.1.2.12.1		not-accessible	Table to list the ICBM counter values. This table is not supported on 10G module.
snAgentHwICBMCounterEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.2.12.1.1		not-accessible	A row representing ICBM counter values for that slot.
U32 snAgentHwICBMCounterSlot	1.3.6.1.4.1.11.2.3.7.11.12.1.2.12.1.1.1	Unsigned32	read-only	Slot number where ICBM resides.
U32 snAgentHwICBMCounterDMA	1.3.6.1.4.1.11.2.3.7.11.12.1.2.12.1.1.2	Unsigned32	read-only	DMA Id within a slot where ICBM resides. Valid only for Jetcore modules. For non-Jetcore modules, this index is ignored by the agent. In this case, value 0 will be returned by the agent.
CTR snAgentHwICBMCounterFreeDepth	1.3.6.1.4.1.11.2.3.7.11.12.1.2.12.1.1.3	Counter	read-only	Current depth of the free queue for this ICBM.
CTR snAgentHwICBMCounterWriteDrop	1.3.6.1.4.1.11.2.3.7.11.12.1.2.12.1.1.4	Counter	read-only	Write sequencer drop count for this ICBM.
CTR snAgentHwICBMCounterWriteInput	1.3.6.1.4.1.11.2.3.7.11.12.1.2.12.1.1.5	Counter	read-only	Write sequencer input counter for this ICBM.
CTR snAgentHwICBMCounterWriteOutput	1.3.6.1.4.1.11.2.3.7.11.12.1.2.12.1.1.6	Counter	read-only	Write sequencer output counter for this ICBM.
CTR snAgentHwICBMCounterReadInput	1.3.6.1.4.1.11.2.3.7.11.12.1.2.12.1.1.7	Counter	read-only	Read sequencer input counter for this ICBM.
CTR snAgentHwICBMCounterReadOutput	1.3.6.1.4.1.11.2.3.7.11.12.1.2.12.1.1.8	Counter	read-only	Read sequencer output counter for this ICBM.
snStackGen	1.3.6.1.4.1.11.2.3.7.11.12.1.5.1
INT snStackPriSwitchMode	1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.1	INTEGER	read-write	The Stackable Management Primary Switch mode either enabled or disabled and the default is disabled mode. enabled(1)...........primary switch enabled disabled(0)..........primary switch disabled
INT snStackMaxSecSwitch	1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.2	INTEGER	read-only	The Maximum Secondary Switches are allowed in the Stackable Management Group.
INT snStackTotalSecSwitch	1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.3	INTEGER	read-only	The Total Secondary Switches currently connected to the Stackable Management Group.
INT snStackSyncAllSecSwitch	1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.4	INTEGER	read-write	Synchronize all the secondary switches in the Stackable Management Group with the following commands. device(2)...........device related parameters. global(3)...........global parameters. local(4)............local parameters. The return result of the above commands are either normal(0)...........normal condition. invalid(1)...........invalid result.
INT snStackSmSlotIndex	1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.5	INTEGER	read-write	The Slot 0 is the Master slot and Slot 1-8 are slaves. All the slot-based MIB data can be retrieved with respect to this slot index such as snChassis global MIB.
INT snStackFmpSetProcess	1.3.6.1.4.1.11.2.3.7.11.12.1.5.1.6	INTEGER	read-only	normal(0) - The set process is either in an idle state or FMP-SET-SUCCESS state. pending(1) - The pending process is waiting for the result of an FMP-SET. failure(2) - The failure result of an FMP-SET.
snStackSecSwitchInfo	1.3.6.1.4.1.11.2.3.7.11.12.1.5.2
snStackSecSwitchTable	1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1		not-accessible	If snSwGroupOperMode is configured as basic mode which is VLAN by Port, Layer2 switching, then this table is valid. Each VLAN switch port could have a number of VLAN IDs.
snStackSecSwitchEntry	1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1		not-accessible	An entry in the Stackable Management Secondary Switch Information table.
INT snStackSecSwitchIndex	1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.1	INTEGER	read-only	The secondary switch index must not be greater than the snStackMaxSecSwitch.
INT snStackSecSwitchSlotId	1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.2	INTEGER	read-write	The secondary switch slot ID must be set before the Configuration command sent from the primary switch to the secondary switch either manually or automatically - snStackSecSwitchCfgCmd.
INT snStackSecSwitchPortCnts	1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.3	INTEGER	read-only	The number of ports in this secondary switch.
INT snStackSecSwitchEnabled	1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.4	INTEGER	read-write	The secondary switch has been selected to Stackable Management Group.
INT snStackSecSwitchAck	1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.5	INTEGER	read-only	The secondary switch has sent reponse to the primary switch.
MAC snStackSecSwitchMacAddr	1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.6	MacAddress	read-only	The secondary switch physical address. The physical address represents a MAC Station.
INT snStackSecSwitchSyncCmd	1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.7	INTEGER	read-write	Synchronize the secondary switches in the Stackable Management Group with the following commands. device(2)...........device related parameters. global(3)...........global parameters. local(4)............local parameters. The return result of the above commands are either normal(0)...........normal condition. invalid(1)...........invalid result.
IP snStackSecSwitchIpAddr	1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.8	IpAddress	read-write	The secondary switch IP Address and is used for manual-command of snStackSecSwitchCfgCmd.
IP snStackSecSwitchSubnetMask	1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.9	IpAddress	read-write	The secondary switch IP Subnet Mask and is used for manual-command of snStackSecSwitchCfgCmd.
INT snStackSecSwitchCfgCmd	1.3.6.1.4.1.11.2.3.7.11.12.1.5.2.1.1.10	INTEGER	read-write	snStackSecSwitchSlotId must be set before the Configuration command sent from the primary switch to the secondary switch either manually or automatically. auto(2)...........auto-configuration command sent. manual(3).........manual-configuration command sent. if manual-mode is used, snStackSecSwitchIpAddr and snStackSecSwitchSubnetMask must be first set before this command is sent. The return result of the above commands are either normal(0)...........normal condition. invalid(1)..........invalid result.

RFC description

Manages Foundry BigIron router switch chassis information including power supply and fan status.

Start monitoring HP/Foundry-heritage chassis-based network switch with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HP-SN-AGENT-MIB

What Is HP-SN-AGENT-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description