| OID symbolic | OID numeric | Type | Access | Description |
|---|
| hpicfSnmpMIB | 1.3.6.1.4.1.11.2.14.11.5.1.38 | | | This MIB module contains HP proprietary
objects for managing SNMP entity. |
| hpicfSnmpNotification | 1.3.6.1.4.1.11.2.14.11.5.1.38.0 | | | |
| NTF hpicfSnmpAuthFail | 1.3.6.1.4.1.11.2.14.11.5.1.38.0.1 | | | The switch sends this notification when an SNMP
SET command fails at the authorization check stage.
This notification applies to SETs within the hpicf tree that
are network security related. This object is controlled
by hpicfSnmpAuthNotifyEnable |
| hpicfSnmpObjects | 1.3.6.1.4.1.11.2.14.11.5.1.38.1 | | | |
| hpicfSnmpConfig | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1 | | | |
| hpicfSnmpGlobalCfg | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1 | | | |
| hpicfSnmpResponseSourceAddrPolicyTable | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.1 | | not-accessible | A table of entries used to configure the policy for
selecting source address while sending SNMP response.
When this entry is configured, the source address field
in the IP PKT header get modified based on the configured
option. There are 4 valid options that can be configured
for ipv4 and ipv6 networks
a) rfc1517
This is the default behavior if no other policy is
configured. In this case the source address will be
the address of the interface from which packet goes
out of the box.
b) user configured IP address
In this case the configured address will be used as
source address in the SNMP response.
c) user configured interface
In this case the IP address configured on the specified
interface will be used as source address in the SNMP
response. In case of multinet interface then smallest
IP address present on the interface in lexicographical
order will be used as source address while sending
SNMP responses for requests.
d) dst_ip_of_request
In this case, the destination IP address present in
the IP header of received SNMP request will be used
as source address in the SNMP response. |
| hpicfSnmpResponseSourceAddrPolicyEntry | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.1.1 | | not-accessible | An entry in the table, containing information about
a single source address. This table allows only 2 values
that can be used as index to this table. These are:
1) hpicfSnmpResponseSourceAddressType = ipv4
Where user wants to configure the source address type
used while sending the SNMP response on IPV4 network.
2) hpicfSnmpResponseSourceAddressType = ipv6
Where user wants to configure the source address type
used while sending the SNMP response on IPV6 network. |
| IPt hpicfSnmpResponseSourceAddressType | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.1.1.1 | InetAddressType | accessible-for-notify | We allow only 2 values for this object as an index for
hpicfSnmpResponseSourceAddrPolicyEntry -
1) hpicfSnmpResponseSourceAddressType = ipv4
Where user wants to configure the source address type
used while sending the SNMP response on IPV4 network
2) hpicfSnmpResponseSourceAddressType = ipv6
Where user wants to configure the source address type
used while sending the SNMP response on IPV6 network. |
| INT hpicfSnmpResponseSourceAddrPolicy | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.1.1.2 | INTEGER | read-create | This specifies the policy for selecting the source
address for outgoing SNMP responses.
a) rfc1517
This is the default behavior if no other policy is
configured. In this case the source address will be
the address of the interface from which packet goes
out of the box.
b) configuredIP
By setting this value will enable the SNMP agent to use
IP addresses specified in hpicfSnmpResponseSourceAddress
object as source address while sending the response.
hpicfSnmpResponseSourceAddress must be set to a valid
and active IP address before setting policy to
configuredIP.
Note: This IP address will be used in the SNMP response
PDU provided it is configured as an IP address on any
one of the interfaces of the device.
c) configuredInterface
By setting this value will enable the SNMP agent to use
IP addresses configured on the interface specified by
hpicfSnmpResponseSourceAddrIfIndex object as source
address while sending the response.
In case of multinet interface then smallest IP
address present on the interface in lexicographical
order will be used as source address while sending
SNMP responses for requests.
hpicfSnmpResponseSourceAddrIfIndex object must be set
to a valid loopback interface number before setting
policy to configuredInterface.
Note: The configured interface's IP address will be used
in the SNMP response PDU provided the interface has an IP
address configured.
d) dst_ip_of_request
In this case, the destination IP address present in
the IP header of received SNMP request will be used as
source address in the SNMP response. |
| IP hpicfSnmpResponseSourceAddress | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.1.1.3 | InetAddress | read-create | This object is used to set the IP address which will be
used as source IP while sending the SNMP response.
This object should be used in conjunction with the
hpicfSnmpResponseSourceAddressType and
hpicfSnmpResponseSourceAddrPolicy.
Note: This IP address will be used in the SNMP response
PDU provided it is configured as an IP address on any
one of the interfaces of the device. |
| NUM hpicfSnmpResponseSourceAddrIfIndex | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.1.1.4 | InterfaceIndexOrZero | read-create | This object is used to set the interface whose IP address
will be used as source IP while sending the SNMP response.
This object should be used in conjunction with the
hpicfSnmpResponseSourceAddressType and
hpicfSnmpResponseSourceAddrPolicy.
Note: The configured interface's IP address will be used
in the SNMP response PDU provided the interface has an IP
address configured. |
| hpicfSnmpTrapSourceAddrTable | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.2 | | not-accessible | A table of entries used to configure the source address
used while generating SNMP Traps. When this entry is
configured, the source address field in the IP PKT header
get modified based on the configured option. |
| hpicfSnmpTrapSourceAddrEntry | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.2.1 | | not-accessible | An entry in the table, containing information about
a single source address. This table allows only 2 values
that can be used as index to this table. These are:
1) hpicfSnmpResponseSourceAddressType = ipv4
Where user wants to configure the source address
used while sending the SNMP TRAPs on IPV4 network.
2) hpicfSnmpResponseSourceAddressType = ipv6
Where user wants to configure the source address
used while sending the SNMP TRAPs on IPV6 network. |
| IPt hpicfSnmpTrapSourceAddressType | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.2.1.1 | InetAddressType | accessible-for-notify | This table allows only 2 values
that can be used as index to this table. These are:
1) hpicfSnmpResponseSourceAddressType = ipv4
Where user wants to configure the source address
used while sending the SNMP TRAPs on IPV4 network.
2) hpicfSnmpResponseSourceAddressType = ipv6
Where user wants to configure the source address
used while sending the SNMP TRAPs on IPV6 network. |
| INT hpicfSnmpTrapSourceAddrPolicy | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.2.1.2 | INTEGER | read-create | This specifies the policy for selecting the source
address for outgoing SNMP responses.
a) rfc1517
This is the default behavior if no other policy is
configured. In this case the source address will be
the address of the interface from which packet goes
out of the box.
b) configuredIP
By setting this value will enable the SNMP agent to use
IP addresses specified in hpicfSnmpResponseSourceAddress
object as source address while sending the response.
hpicfSnmpTrapSourceAddress must be set to a valid
and active ip address before setting policy to
configuredIP.
Note: This IP address will be used in the SNMP trap
PDU provided it is configured as an IP address on any
one of the interfaces of the device.
c) configuredInterface
By setting this value will enable the SNMP agent to use
IP addresses configured on the interface specified by
hpicfSnmpResponseSourceAddrIfIndex object as source
address while sending the response.
In case of multinet interface then smallest IP
address present on the interface in lexicographical
order will be used as source address while sending
SNMP responses for requests.
Note: The configured interface's IP address will be used
in the SNMP trap PDU provided the interface has an IP
address configured.
hpicfSnmpTrapSourceAddrIfIndex object must be set
to a valid loopback interface number before setting
policy to configuredInterface. |
| IP hpicfSnmpTrapSourceAddress | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.2.1.3 | InetAddress | read-create | This object is used to set the IP address which will be
used as source IP while sending the SNMP TRAPs.
This object should be used in conjunction with the
hpicfSnmpResponseSourceAddressType and
hpicfSnmpTrapSourceAddrPolicy.
Note: This IP address will be used in the SNMP trap
PDU provided it is configured as an IP address on any
one of the interfaces of the device. |
| NUM hpicfSnmpTrapSourceAddrIfIndex | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.2.1.4 | InterfaceIndexOrZero | read-create | This object is used to set the interface whose IP address
will be used as source IP while sending the SNMP TRAPs.
This object should be used in conjunction with the
hpicfSnmpResponseSourceAddressType and
hpicfSnmpTrapSourceAddrPolicy.
Note: The configured interface's IP address will be used
in the SNMP trap PDU provided the interface has an IP
address configured. |
| INT hpicfSnmpAuthNotifyEnable | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.3 | INTEGER | read-write | Controls whether hpicfSnmpAuthFail notifications will be generated.
The default value is 1 (Enabled). A value of 2 represents
Disabled. Writing this object requires authentication, such
as provided by SNMPv3.
NOTE that hpicfSnmpAuthFail and snmpEnableAuthenTraps (RFC-1157)
are mutually exclusive. While they may both be disabled, only
one may be enabled at any given time. Notifications enabled by
hpicfSnmpAuthFail are more comprehensive and are therefore
recommended. |
| hpicfSnmpNotificationObjects | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.2 | | | |
| C32 hpicfSnmpAuthFailCount | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.2.1 | Counter32 | accessible-for-notify | A count of SNMP authorization failures detected by the SNMP entity. |
| IPt hpicfSnmpAuthFailIPType | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.2.2 | InetAddressType | accessible-for-notify | Type of IP address contained in hpicfSnmpAuthFailIP. |
| IP hpicfSnmpAuthFailIP | 1.3.6.1.4.1.11.2.14.11.5.1.38.1.2.3 | InetAddress | accessible-for-notify | IP address of sender of message that failed authentication. |
| hpicfSnmpConformance | 1.3.6.1.4.1.11.2.14.11.5.1.38.2 | | | |
| hpicfSnmpCompliances | 1.3.6.1.4.1.11.2.14.11.5.1.38.2.1 | | | |
| hpicfSnmpCompliance | 1.3.6.1.4.1.11.2.14.11.5.1.38.2.1.1 | | | A compliance statement for HP Routing switches with SNMP |
| hpicfSnmpCompliance1 | 1.3.6.1.4.1.11.2.14.11.5.1.38.2.1.2 | | | A compliance statement for HP Routing switches with SNMP |
| hpicfSnmpCompliancesGroups | 1.3.6.1.4.1.11.2.14.11.5.1.38.2.2 | | | |
| hpicfSnmpResponseSourceAddrTableCompliancesGroup | 1.3.6.1.4.1.11.2.14.11.5.1.38.2.2.1 | | | A collection of objects allowing configuration of policies
in the switch for selecting the source address used while
generating SNMP response |
| hpicfSnmpTrapSourceAddrTableCompliancesGroup | 1.3.6.1.4.1.11.2.14.11.5.1.38.2.2.2 | | | A collection of objects allowing configuration of source
addresses for SNMP traps generated by the switch. |
| hpicfSnmpResponseSourceAddrTableGroup | 1.3.6.1.4.1.11.2.14.11.5.1.38.2.2.3 | | | Description. |
| hpicfSnmpTrapSourceAddrTableGroup | 1.3.6.1.4.1.11.2.14.11.5.1.38.2.2.4 | | | Description. |
| hpicfSnmpNotifyObjectGroup | 1.3.6.1.4.1.11.2.14.11.5.1.38.2.2.5 | | | The operational status of hpicfSwitchAuthServerFail notifications.
The default value is 1 (Enabled). A value of 2 represents
Disabled. Writing this object requires authentication, such
as provided by SNMPv3. |
| hpicfSnmpNotificationGroup | 1.3.6.1.4.1.11.2.14.11.5.1.38.2.2.6 | | | Description. |
