HP-ICF-SNMP-MIB :: hpicfSnmpTrapSourceAddrPolicy

MIB Reference — IPNetwork Monitor · Updated September 21, 2026

All MIBs › HP-ICF-SNMP-MIB › hpicfSnmpTrapSourceAddrPolicy

hpicfSnmpTrapSourceAddrPolicy

Module: HP-ICF-SNMP-MIB

OID (symbolic): HP-ICF-SNMP-MIB::hpicfSnmpTrapSourceAddrPolicy

OID (numeric): 1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.2.1.2

Node type: OBJECT-TYPE

Type: INTEGER

Access: read-create

Description: This specifies the policy for selecting the source address for outgoing SNMP responses. a) rfc1517 This is the default behavior if no other policy is configured. In this case the source address will be the address of the interface from which packet goes out of the box. b) configuredIP By setting this value will enable the SNMP agent to use IP addresses specified in hpicfSnmpResponseSourceAddress object as source address while sending the response. hpicfSnmpTrapSourceAddress must be set to a valid and active ip address before setting policy to configuredIP. Note: This IP address will be used in the SNMP trap PDU provided it is configured as an IP address on any one of the interfaces of the device. c) configuredInterface By setting this value will enable the SNMP agent to use IP addresses configured on the interface specified by hpicfSnmpResponseSourceAddrIfIndex object as source address while sending the response. In case of multinet interface then smallest IP address present on the interface in lexicographical order will be used as source address while sending SNMP responses for requests. Note: The configured interface's IP address will be used in the SNMP trap PDU provided the interface has an IP address configured. hpicfSnmpTrapSourceAddrIfIndex object must be set to a valid loopback interface number before setting policy to configuredInterface.

What is hpicfSnmpTrapSourceAddrPolicy?

This selects the policy for choosing the source IP address the switch places in outgoing SNMP traps, offering the same rfc1517, configuredIP, configuredInterface, or dstIpOfRequest choices as the response-address policy. An admin sets this so traps sent to a network management station consistently appear to originate from a known, stable address rather than the interface nearest the trap destination. For example, setting this to configuredInterface(3) makes traps use the IP address of the loopback interface named in hpicfSnmpTrapSourceAddrIfIndex.

OID Breakdown

Upper-level ancestors (13 from the standard OID tree / other modules)
Numeric OIDNameModule
1isoLANART-AGENT
1.3orgAirPair-MIB
1.3.6dodAirPair-MIB
1.3.6.1internetAirPair-MIB
1.3.6.1.4privateAirPair-MIB
1.3.6.1.4.1enterprisesAirPair-MIB
1.3.6.1.4.1.11hpCLJ8500-MIB
1.3.6.1.4.1.11.2nmCLJ8500-MIB
1.3.6.1.4.1.11.2.14icfCONFIG-MIB
1.3.6.1.4.1.11.2.14.11hpicfObjectsCONFIG-MIB
1.3.6.1.4.1.11.2.14.11.5hpicfSwitchCONFIG-MIB
1.3.6.1.4.1.11.2.14.11.5.1hpSwitchCONFIG-MIB
1.3.6.1.4.1.11.2.14.11.5.1.38hpicfSnmpMIBHP-ICF-OID
Numeric OIDNameModule
1.3.6.1.4.1.11.2.14.11.5.1.38.1hpicfSnmpObjectsHP-ICF-SNMP-MIB
1.3.6.1.4.1.11.2.14.11.5.1.38.1.1hpicfSnmpConfigHP-ICF-SNMP-MIB
1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1hpicfSnmpGlobalCfgHP-ICF-SNMP-MIB
1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.2hpicfSnmpTrapSourceAddrTableHP-ICF-SNMP-MIB
1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.2.1hpicfSnmpTrapSourceAddrEntryHP-ICF-SNMP-MIB
1.3.6.1.4.1.11.2.14.11.5.1.38.1.1.1.2.1.2hpicfSnmpTrapSourceAddrPolicyHP-ICF-SNMP-MIB