All MIBs › HP-ICF-FAULT-FINDER-MIB › hpicfFfDisablePortTolerance
hpicfFfDisablePortTolerance
Module: HP-ICF-FAULT-FINDER-MIB
OID (symbolic): HP-ICF-FAULT-FINDER-MIB::hpicfFfDisablePortTolerance
OID (numeric): 1.3.6.1.4.1.11.2.14.11.1.7.1.1.4
Node type: OBJECT-TYPE
Type: HpicfFaultTolerance
Access: read-write
Description: The tolerance level used to calculate the port disable threshold for this fault type. The value of an instance of this object MUST be greater than the value of the corresponding instance of the hpicfFfWarnTolerance.
The agent will periodically check relevant statistics for each port for each type of fault. If the port disable threshold has been exceeded, and port disable is enabled for that fault type, an hpicfFaultFinderTrap notification will be sent. In addition, an entry will be made in the hpicfFfLogTable for the fault.
Ports will not be disabled until at least one polling interval after a warning has fired. In addition, the agent may further delay disabling a port in certain situations. For example, it may choose to delay disabling a cascade port to give the cascaded device a chance to correct the problem.
What is hpicfFfDisablePortTolerance?
The tolerance level used to compute the port-disable threshold for this fault type; it must be set higher than hpicfFfWarnTolerance, since disabling should only trigger after warnings have already been raised.
Examples
Walk all instances (SNMPv2c):
snmpwalk -v2c -c public <target> 1.3.6.1.4.1.11.2.14.11.1.7.1.1.4 snmpwalk -v2c -c public <target> HP-ICF-FAULT-FINDER-MIB::hpicfFfDisablePortTolerance
Get a specific instance (index 1):
snmpget -v2c -c public <target> 1.3.6.1.4.1.11.2.14.11.1.7.1.1.4.1 snmpget -v2c -c public <target> HP-ICF-FAULT-FINDER-MIB::hpicfFfDisablePortTolerance.1
Set instance 1 (SNMPv2c):
snmpset -v2c -c private <target> 1.3.6.1.4.1.11.2.14.11.1.7.1.1.4.1 s <value>
Start monitoring HP ProCurve web-managed switch (automated cabling/port fault detection) with a free 30-day trial of IPNetwork Monitor. Create custom SNMP monitor using the HP-ICF-FAULT-FINDER-MIB::hpicfFfDisablePortTolerance OID value, configure state conditions and alerts, and monitor any HP ProCurve web-managed switch (automated cabling/port fault detection) from a single console.
OID Breakdown
Upper-level ancestors (11 from the standard OID tree / other modules)
| Numeric OID | Name | Module |
|---|---|---|
| 1 | iso | LANART-AGENT |
| 1.3 | org | AirPair-MIB |
| 1.3.6 | dod | AirPair-MIB |
| 1.3.6.1 | internet | AirPair-MIB |
| 1.3.6.1.4 | private | AirPair-MIB |
| 1.3.6.1.4.1 | enterprises | AirPair-MIB |
| 1.3.6.1.4.1.11 | hp | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2 | nm | CLJ8500-MIB |
| 1.3.6.1.4.1.11.2.14 | icf | CONFIG-MIB |
| 1.3.6.1.4.1.11.2.14.11 | hpicfObjects | CONFIG-MIB |
| 1.3.6.1.4.1.11.2.14.11.1 | hpicfCommon | HP-ICF |
| Numeric OID | Name | Module |
|---|---|---|
| 1.3.6.1.4.1.11.2.14.11.1.7 | hpicfFaultFinder | HP-ICF-FAULT-FINDER-MIB |
| 1.3.6.1.4.1.11.2.14.11.1.7.1 | hpicfFfControlTable | HP-ICF-FAULT-FINDER-MIB |
| 1.3.6.1.4.1.11.2.14.11.1.7.1.1 | hpicfFfControlEntry | HP-ICF-FAULT-FINDER-MIB |
| 1.3.6.1.4.1.11.2.14.11.1.7.1.1.4 | hpicfFfDisablePortTolerance | HP-ICF-FAULT-FINDER-MIB |