EdgeSwitch-ROUTING-MIB

All MIBs › EdgeSwitch-ROUTING-MIB

Organization: Broadcom Inc

Last Updated: 2011-01-26

Category: Technology: Routing, Vendor: EdgeSwitch/Ubiquiti

Description: Ubiquiti EdgeSwitch routing MIB for managing IPv4 static routes, routing tables, and layer-3 forwarding configuration.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is EdgeSwitch-ROUTING-MIB?

EdgeSwitch-ROUTING-MIB is a Ubiquiti private MIB (based on the Broadcom FastPath routing stack) for managing IPv4 static routes, routing table contents, and layer-3 forwarding configuration on Ubiquiti EdgeSwitch devices. Although no specific object list was retrievable for this batch, based on its name and the underlying FastPath routing lineage it would expose configuration objects for static route entries and read-only tables reflecting the current IP routing table and per-interface routing status. Its monitoring value would center on the software/control-plane status of layer-3 forwarding -- confirming configured static routes are present and active, and that the routing table reflects expected next-hops -- rather than physical hardware sensors. It is built on the Broadcom FastPath routing MIB framework shared across several white-label/OEM switch vendors, rather than being wholly original to Ubiquiti. It is deployed on Ubiquiti EdgeSwitch layer-3 switches in small-to-midsize network environments requiring basic static IP routing, and administrators can download the EdgeSwitch-ROUTING-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in EdgeSwitch-ROUTING-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ubiquiti EdgeSwitch layer-3 managed switch

Monitoring Examples

No sample objects were available for this MIB in the provided data, so a concrete polling scenario naming specific tables/objects cannot be responsibly constructed; in general, an operator would expect to query a routing/route table to confirm a configured static route's next-hop and interface are active as intended.

What Can Be Monitored

static route configuration
IP routing table entries
route next-hop status

Imported Objects

From EdgeSwitch-REF-MIB

fastPath

OBJECT-IDENTITY

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero
ifIndex	OBJECT-TYPE

From OSPF-MIB

RouterID
ospfAreaEntry	OBJECT-TYPE
ospfIfEntry
ospfVirtIfEntry

From RFC1213-MIB

DisplayString
PhysAddress

From RIPv2-MIB

rip2IfConfEntry

OBJECT-TYPE

From SNMPv2-SMI

Counter32
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION
TruthValue

From VRRP-MIB

vrrpOperVrId

OBJECT-TYPE

How to Use in IPNetwork Monitor

Example using agentDhcpClientMsgsReceived OID:

Select an Ubiquiti EdgeSwitch (Broadcom FastPath-based) switch (IPv4 static routing/L3 forwarding) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type agentDhcpClientMsgsReceived into the Find box to locate it in the OID tree, then select it and click OK. The Number of DHCP Requests Received. Total number of DHCP requests received from all clients. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
fastPathRouting	1.3.6.1.4.1.4413.1.1.2			The Ubiquiti Private MIB for FastPath Routing
agentSwitchArpGroup	1.3.6.1.4.1.4413.1.1.2.1
I32 agentSwitchArpAgeoutTime	1.3.6.1.4.1.4413.1.1.2.1.1	Integer32	read-write	Configures the ARP entry ageout time in seconds. Allowable range: 15-21600
I32 agentSwitchArpResponseTime	1.3.6.1.4.1.4413.1.1.2.1.2	Integer32	read-write	Configures the ARP request response timeout in seconds. Allowable range: 1-10
I32 agentSwitchArpMaxRetries	1.3.6.1.4.1.4413.1.1.2.1.3	Integer32	read-write	Configures the ARP count of maximum request for retries. Allowable range: 0-10
I32 agentSwitchArpCacheSize	1.3.6.1.4.1.4413.1.1.2.1.4	Integer32	read-write	Configures the ARP maximum number of entries in the cache. Allowable range is platform-specific.
INT agentSwitchArpDynamicRenew	1.3.6.1.4.1.4413.1.1.2.1.5	INTEGER	read-write	This indicates the current setting of ARP dynamic renew mode.
G32 agentSwitchArpTotalEntryCountCurrent	1.3.6.1.4.1.4413.1.1.2.1.6	Gauge32	read-only	Current number of entries in the ARP cache.
G32 agentSwitchArpTotalEntryCountPeak	1.3.6.1.4.1.4413.1.1.2.1.7	Gauge32	read-only	Peak number of entries recorded in the ARP cache over time. This value is restarted whenever the ARP cache size is changed.
G32 agentSwitchArpStaticEntryCountCurrent	1.3.6.1.4.1.4413.1.1.2.1.8	Gauge32	read-only	Current number of configured static ARP entries.
I32 agentSwitchArpStaticEntryCountMax	1.3.6.1.4.1.4413.1.1.2.1.9	Integer32	read-only	Maximum number of configurable static ARP entries.
agentSwitchArpTable	1.3.6.1.4.1.4413.1.1.2.1.10		not-accessible	This table augments the MIB-II ipNetToMediaTable by providing per-interface ARP entry information.
agentSwitchArpEntry	1.3.6.1.4.1.4413.1.1.2.1.10.1		not-accessible
TIK agentSwitchArpAge	1.3.6.1.4.1.4413.1.1.2.1.10.1.1	TimeTicks	read-only	This defines the time (in seconds) since the ARP entry was last refreshed. This value is 0 for ARP entries of type local(1) or static(3), since these entries are not subject to aging.
IP agentSwitchArpIpAddress	1.3.6.1.4.1.4413.1.1.2.1.10.1.2	IpAddress	read-only	The IP Address assigned to each interface.
PHY agentSwitchArpMacAddress	1.3.6.1.4.1.4413.1.1.2.1.10.1.3	PhysAddress	read-create	The hardware MAX Address that each interface maps to.
I32 agentSwitchArpInterface	1.3.6.1.4.1.4413.1.1.2.1.10.1.4	Integer32	read-create	The Associated IfIndex which identified the ARP Entry.
INT agentSwitchArpType	1.3.6.1.4.1.4413.1.1.2.1.10.1.5	INTEGER	read-only	The type of ARP entry.
ROW agentSwitchArpStatus	1.3.6.1.4.1.4413.1.1.2.1.10.1.6	RowStatus	read-write	The status of this ARP entry. Setting this object destroy will remove the entry.
agentSwitchLocalProxyArpTable	1.3.6.1.4.1.4413.1.1.2.1.11		not-accessible	This table contains the per-interface configuration parameters for Local Proxy Arp.
agentSwitchLocalProxyArpEntry	1.3.6.1.4.1.4413.1.1.2.1.11.1		not-accessible	Represents a logical row in the agentSwitchLocalProxyArpTable
INT agentSwitchLocalProxyArpMode	1.3.6.1.4.1.4413.1.1.2.1.11.1.1	INTEGER	read-write	The Local Proxy Arp Mode for the interface.
agentSwitchIntfArpTable	1.3.6.1.4.1.4413.1.1.2.1.12		not-accessible	This table augments the MIB-II ipNetToMediaTable by providing per-interface ARP entry information.
agentSwitchIntfArpEntry	1.3.6.1.4.1.4413.1.1.2.1.12.1		not-accessible
IP agentSwitchIntfArpIpAddress	1.3.6.1.4.1.4413.1.1.2.1.12.1.1	IpAddress	not-accessible	The Type of Address assigned to this interface.
NUM agentSwitchIntfArpIfIndex	1.3.6.1.4.1.4413.1.1.2.1.12.1.2	InterfaceIndex	not-accessible	The Associated IfIndex which identified the ARP Entry. This value must be specified for static ARP entries on an unnumbered interface
TIK agentSwitchIntfArpAge	1.3.6.1.4.1.4413.1.1.2.1.12.1.3	TimeTicks	read-only	This defines the time (in seconds) since the ARP entry was last refreshed. This value is 0 for ARP entries of type local(1) or static(3), since these entries are not subject to aging.
PHY agentSwitchIntfArpMacAddress	1.3.6.1.4.1.4413.1.1.2.1.12.1.4	PhysAddress	read-create	The hardware MAX Address that each interface maps to.
INT agentSwitchIntfArpType	1.3.6.1.4.1.4413.1.1.2.1.12.1.5	INTEGER	read-only	The type of ARP entry.
ROW agentSwitchIntfArpStatus	1.3.6.1.4.1.4413.1.1.2.1.12.1.6	RowStatus	read-create	The status of this ARP entry. Setting this object destroy will remove the entry.
agentSwitchIpGroup	1.3.6.1.4.1.4413.1.1.2.2
INT agentSwitchIpRoutingMode	1.3.6.1.4.1.4413.1.1.2.2.1	INTEGER	read-write	Administratively enables/disables routing on the switch.
IP agentSwitchIpDefaultGateway	1.3.6.1.4.1.4413.1.1.2.2.2	IpAddress	read-write	Specifies the Default Gateway manually configured.
agentSwitchIpInterfaceTable	1.3.6.1.4.1.4413.1.1.2.2.3		not-accessible
agentSwitchIpInterfaceEntry	1.3.6.1.4.1.4413.1.1.2.2.3.1		not-accessible
I32 agentSwitchIpInterfaceIfIndex	1.3.6.1.4.1.4413.1.1.2.2.3.1.1	Integer32	read-only	The IfIndex associated with this instance.
INT agentSwitchIPAddressConfigMethod	1.3.6.1.4.1.4413.1.1.2.2.3.1.2	INTEGER	read-write	The Source of the IP Address. User can set the object to none(0) or dhcp(2). Option dhcp(2) enables Dhcp Client on the interface. Option none(0) disables Dhcp Client on the interface. Get on this object returns manual(1) only when the interface has a manually configured address.
IP agentSwitchIpInterfaceIpAddress	1.3.6.1.4.1.4413.1.1.2.2.3.1.3	IpAddress	read-write	The IpAddress assigned to this interface. When setting this value, the value of agentSwitchIpInterfaceNetMask must be set at the same time.
IP agentSwitchIpInterfaceNetMask	1.3.6.1.4.1.4413.1.1.2.2.3.1.4	IpAddress	read-write	The NetMask assigned to this interface. When setting this value, the value of agentSwitchIpInterfaceIpAddress must be set at the same time.
INT agentSwitchIpInterfaceClearIp	1.3.6.1.4.1.4413.1.1.2.2.3.1.5	INTEGER	read-write	Sets the interfaces IpAddress and NetMask back to 0.0.0.0
INT agentSwitchIpInterfaceRoutingMode	1.3.6.1.4.1.4413.1.1.2.2.3.1.6	INTEGER	read-write	Enables or disables routing for this interface.
INT agentSwitchIpInterfaceProxyARPMode	1.3.6.1.4.1.4413.1.1.2.2.3.1.7	INTEGER	read-write	Enables or disables Proxy ARP for this interface.
U32 agentSwitchIpInterfaceMtuValue	1.3.6.1.4.1.4413.1.1.2.2.3.1.8	Unsigned32	read-write	Configures the MTU value for this interface. The applicable range is 68 to the , in bytes. Get of this object returns the effective MTU value on the interface. Set of this object with a value of 0 resets the MTU to the default IP MTU value on the interface.
U32 agentSwitchIpInterfaceBandwidth	1.3.6.1.4.1.4413.1.1.2.2.3.1.9	Unsigned32	read-write	Configures the Bandwidth value for this interface. If the value returned is 0 bandwidth for this interface is not Configured.
NUM agentSwitchIpInterfaceUnnumberedIfIndex	1.3.6.1.4.1.4413.1.1.2.2.3.1.10	InterfaceIndexOrZero	read-write	If this object is non-zero, it indicates that the interface is unnumbered, and specifies which interface the address is borrowed from.
INT agentSwitchIpInterfaceIcmpUnreachables	1.3.6.1.4.1.4413.1.1.2.2.3.1.11	INTEGER	read-write	If this object is enable, it indicates that ICMP unreachables can be sent on this interface.
INT agentSwitchIpInterfaceIcmpRedirects	1.3.6.1.4.1.4413.1.1.2.2.3.1.12	INTEGER	read-write	If this object is enable and agentSwitchIpIcmpRedirectsMode is also enable ICMP Redirects can be sent on this interface.
INT agentSwitchDhcpOperation	1.3.6.1.4.1.4413.1.1.2.2.3.1.13	INTEGER	read-write	Renew or Release the IP Address learned through DHCP. Get on this object always gives none. none means no operation is performed on dhcp.
INT agentSwitchIpInterfaceSuppressed	1.3.6.1.4.1.4413.1.1.2.2.3.1.14	INTEGER	read-only	This mib variable contains the following values, which has the meaning as: 'unsuppressed' - The interface is not suppressed 'suppressed' - The interface is suppressed
U32 agentSwitchIpInterfaceNumberOfFlaps	1.3.6.1.4.1.4413.1.1.2.2.3.1.15	Unsigned32	read-only	This mib variable displays the number of flaps occurred on the interface
U32 agentSwitchIpInterfaceCurrentPenalty	1.3.6.1.4.1.4413.1.1.2.2.3.1.16	Unsigned32	read-only	This mib variable displays the current penalty of an interface
U32 agentSwitchIpInterfaceReUseTime	1.3.6.1.4.1.4413.1.1.2.2.3.1.17	Unsigned32	read-only	This mib variable displays the number of seconds until the interface is allowed to come up
agentSwitchIpRouterDiscoveryTable	1.3.6.1.4.1.4413.1.1.2.2.4		not-accessible	There is no global administrative flag for router discovery. The global routing flag (agentSwitchIpRoutingMode) will be used for this purpose. If routing is disabled, router discovery is disabled as well.
agentSwitchIpRouterDiscoveryEntry	1.3.6.1.4.1.4413.1.1.2.2.4.1		not-accessible
I32 agentSwitchIpRouterDiscoveryIfIndex	1.3.6.1.4.1.4413.1.1.2.2.4.1.1	Integer32	read-only	Interface Number to configure Router Discovery on.
INT agentSwitchIpRouterDiscoveryAdvertiseMode	1.3.6.1.4.1.4413.1.1.2.2.4.1.2	INTEGER	read-write	Enable or disable router discovery on the interface.
I32 agentSwitchIpRouterDiscoveryMaxAdvertisementInterval	1.3.6.1.4.1.4413.1.1.2.2.4.1.3	Integer32	read-write	Maximum time allowed between sending router advertisements from the interface.
I32 agentSwitchIpRouterDiscoveryMinAdvertisementInterval	1.3.6.1.4.1.4413.1.1.2.2.4.1.4	Integer32	read-write	Minimum time allowed between sending router advertisements from the interface. This value must be less than or equal to agentSwitchIpRouterDiscoveryMaxAdvertisementInterval.
I32 agentSwitchIpRouterDiscoveryAdvertisementLifetime	1.3.6.1.4.1.4413.1.1.2.2.4.1.5	Integer32	read-write	Value of lifetime field of router advertsisement sent from the interface. This value must be greater than or equal to agentSwitchIpRouterDiscoveryMaxAdvertisementInterval.
I32 agentSwitchIpRouterDiscoveryPreferenceLevel	1.3.6.1.4.1.4413.1.1.2.2.4.1.6	Integer32	read-write	Preferability of the address as a default router address, related to other addresses on the same subnet. This is defined as the larger the number, the higher the preference.
IP agentSwitchIpRouterDiscoveryAdvertisementAddress	1.3.6.1.4.1.4413.1.1.2.2.4.1.7	IpAddress	read-write	Address used when sending router advertisements from the interface.
agentSwitchIpVlanTable	1.3.6.1.4.1.4413.1.1.2.2.5		not-accessible
agentSwitchIpVlanEntry	1.3.6.1.4.1.4413.1.1.2.2.5.1		not-accessible	A Static VLAN for which routing can be enabled/disabled
I32 agentSwitchIpVlanId	1.3.6.1.4.1.4413.1.1.2.2.5.1.1	Integer32	read-only	The Vlan's Id.
I32 agentSwitchIpVlanIfIndex	1.3.6.1.4.1.4413.1.1.2.2.5.1.2	Integer32	read-only	The IfIndex associated with this VLAN.
ROW agentSwitchIpVlanRoutingStatus	1.3.6.1.4.1.4413.1.1.2.2.5.1.3	RowStatus	read-create	Status of Routing mode per Vlan. active(1) - Vlan is enabled for routing createAndGo(4) - Adds Vlan entry for routing destroy(6) - Removes Vlan from routing
agentSwitchSecondaryAddressTable	1.3.6.1.4.1.4413.1.1.2.2.6		not-accessible	Contains a list of secondary IP Addresses associated with an interface.
agentSwitchSecondaryAddressEntry	1.3.6.1.4.1.4413.1.1.2.2.6.1		not-accessible	A secondary IP Address for a given interface. This IP Address must not conflict with the IP Address configured in the agentSwitchIpInterfaceTable.
IP agentSwitchSecondaryIpAddress	1.3.6.1.4.1.4413.1.1.2.2.6.1.1	IpAddress	not-accessible	The Secondary IP Address assigned to this interface.
IP agentSwitchSecondaryNetMask	1.3.6.1.4.1.4413.1.1.2.2.6.1.2	IpAddress	read-create	The Secondary Net Mask assigned to this interface. This value must be set during creation, and can not be changed.
ROW agentSwitchSecondaryStatus	1.3.6.1.4.1.4413.1.1.2.2.6.1.3	RowStatus	read-create	Creates a new entry in the Secondary Address table. Allowed values are: createAndGo(4) - Creates an entry in this table, associating the address with a given interface. The agentSwitchSecondaryNetMask object must be set during creation. destroy(6) - Removes the associated address from the interface.
agentSwitchHelperAddressTable	1.3.6.1.4.1.4413.1.1.2.2.7		not-accessible	Replaced by agentSwitchIntfIpHelperAddressTable.
agentSwitchHelperAddressEntry	1.3.6.1.4.1.4413.1.1.2.2.7.1		not-accessible	A Helper IP Address for a given interface.
IP agentSwitchHelperIpAddress	1.3.6.1.4.1.4413.1.1.2.2.7.1.1	IpAddress	not-accessible	The Helper IP Address assigned to this interface.
ROW agentSwitchHelperStatus	1.3.6.1.4.1.4413.1.1.2.2.7.1.2	RowStatus	read-create	Creates a new entry in the Helper Address table. Allowed values are: createAndGo(4) - Creates an entry in this table, associating the address with a given interface. The agentSwitchHelperNetMask object must be set during creation. destroy(6) - Removes the associated address from the interface.
agentSwitchIpIcmpControlGroup	1.3.6.1.4.1.4413.1.1.2.2.8
INT agentSwitchIpIcmpEchoReplyMode	1.3.6.1.4.1.4413.1.1.2.2.8.1	INTEGER	read-write	Sets the administrative Echo Reply Mode.
INT agentSwitchIpIcmpRedirectsMode	1.3.6.1.4.1.4413.1.1.2.2.8.2	INTEGER	read-write	Sets the administrative Mode for sending Redirects.
I32 agentSwitchIpIcmpRateLimitInterval	1.3.6.1.4.1.4413.1.1.2.2.8.3	Integer32	read-write	Specifies the time interval between tokens being placed in the bucket for ICMP Ratelimit.
I32 agentSwitchIpIcmpRateLimitBurstSize	1.3.6.1.4.1.4413.1.1.2.2.8.4	Integer32	read-write	Specifies the number of tokens to be placed after timeout.
agentSwitchIntfIpHelperAddressTable	1.3.6.1.4.1.4413.1.1.2.2.10		not-accessible	Contains a list of IP helper addresses associated with an interface.
agentSwitchIntfIpHelperAddressEntry	1.3.6.1.4.1.4413.1.1.2.2.10.1		not-accessible	An IP helper address for a given interface.
IP agentSwitchIntfIpHelperIpAddress	1.3.6.1.4.1.4413.1.1.2.2.10.1.1	IpAddress	not-accessible	An IP helper address for packets received on this interface. An address of 0.0.0.0 identifies the entry as a discard entry. Packets that match a discard entry are dropped.
U32 agentSwitchIntfIpHelperUdpPort	1.3.6.1.4.1.4413.1.1.2.2.10.1.2	Unsigned32	not-accessible	UDP port number. Received packets with this destination UDP port number are forwarded to the helper address in this entry.
T/F agentSwitchIntfIpHelperDiscard	1.3.6.1.4.1.4413.1.1.2.2.10.1.3	TruthValue	read-write	Variable obsoleted. To create a discard entry, set the helper address to 0.0.0.0.
U32 agentSwitchIntfIpHelperHitCount	1.3.6.1.4.1.4413.1.1.2.2.10.1.4	Unsigned32	read-only	The number of times a packet has been forwarded or discarded according to this entry.
ROW agentSwitchIntfIpHelperStatus	1.3.6.1.4.1.4413.1.1.2.2.10.1.5	RowStatus	read-create	Creates a new entry in the Helper Address table. Allowed values are: createAndGo(4) - Creates an IP helper entry in this table. destroy(6) - Removes the IP helper entry.
INT agentSwitchClearIpDefaultGateway	1.3.6.1.4.1.4413.1.1.2.2.11	INTEGER	read-write	Resets the Global Default Gateway address.
agentRouterRipConfigGroup	1.3.6.1.4.1.4413.1.1.2.3
INT agentRouterRipAdminState	1.3.6.1.4.1.4413.1.1.2.3.1	INTEGER	read-write	Sets the administrative mode of RIP in the router.
INT agentRouterRipSplitHorizonMode	1.3.6.1.4.1.4413.1.1.2.3.2	INTEGER	read-write	Sets the RIP split horizon operating mode in the router. A value of none(1) means split horizon processing is disabled. When set to simple(2), the simple split horizon technique is used. When set to poisonReverse(3), the split horizon with poison reverse technique is used. The default split horizon mode is simple(2).
INT agentRouterRipAutoSummaryMode	1.3.6.1.4.1.4413.1.1.2.3.3	INTEGER	read-write	Sets the RIP auto summarization mode in the router. A value of enable(1) means that routes advertized by this RIP router are combined, or summarized, whenever possible into aggregates. When set to disable(2), routes are not aggregated in RIP updates generated by this router. The default auto summary mode is enable(1).
INT agentRouterRipHostRoutesAcceptMode	1.3.6.1.4.1.4413.1.1.2.3.4	INTEGER	read-write	Sets the RIP host route acceptance mode in the router. A value of enable(1) means that host routes advertized to this RIP router will be accepted (learned) into its routing table. When set to disable(2), host routes advertized in RIP updates from neighboring routers are ignored. The default host routes accept mode is enable(1).
I32 agentRouterRipDefaultMetric	1.3.6.1.4.1.4413.1.1.2.3.5	Integer32	read-write	Default metric of redistributed routes, when RIP redistributes from other protocols. {0} indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..15).
T/F agentRouterRipDefaultMetricConfigured	1.3.6.1.4.1.4413.1.1.2.3.6	TruthValue	read-write	Flag to determine whether RIP default-metric is configured or not. Set to 'false' to unconfigure the default route metric. Set to 'true' is not allowed.
T/F agentRouterRipDefaultInfoOriginate	1.3.6.1.4.1.4413.1.1.2.3.7	TruthValue	read-write	Flag to determine, whether RIP can advertise a default-route learned from another protocol.
agentRipRouteRedistTable	1.3.6.1.4.1.4413.1.1.2.3.8		not-accessible	This table contains the MIB objects required to configure route-redistribution for RIP. Here, RIP is the Destination protocol and the source protocols can be any of : BGP, OSPF, Static, Connected.
agentRipRouteRedistEntry	1.3.6.1.4.1.4413.1.1.2.3.8.1		not-accessible
INT agentRipRouteRedistSource	1.3.6.1.4.1.4413.1.1.2.3.8.1.1	INTEGER	read-only	Source route, from which RIP can redistribute routes. This object also acts as the identifier for the RIP redistribution Table entry.
INT agentRipRouteRedistMode	1.3.6.1.4.1.4413.1.1.2.3.8.1.2	INTEGER	read-write	User enabels/disables route-redistribution for a particular source protocol.
I32 agentRipRouteRedistMetric	1.3.6.1.4.1.4413.1.1.2.3.8.1.3	Integer32	read-write	Metric used for redistributing a particular source protocol route into RIP. {0} indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..15).
T/F agentRipRouteRedistMetricConfigured	1.3.6.1.4.1.4413.1.1.2.3.8.1.4	TruthValue	read-write	Flag to determine whether RIP redistribute-metric is configured or not. Set to 'false' to unconfigure redistribute metric. Set to 'true' is not allowed.
INT agentRipRouteRedistMatchInternal	1.3.6.1.4.1.4413.1.1.2.3.8.1.5	INTEGER	read-write	If this flag is true, RIP redistributes OSPF internal routes. It will be non-applicable, when source protocol is other than ospf.
INT agentRipRouteRedistMatchExternal1	1.3.6.1.4.1.4413.1.1.2.3.8.1.6	INTEGER	read-write	If this flag is true, RIP redistributes OSPF External1 routes. It will be non-applicable, when source protocol is other than ospf.
INT agentRipRouteRedistMatchExternal2	1.3.6.1.4.1.4413.1.1.2.3.8.1.7	INTEGER	read-write	If this flag is true, RIP redistributes OSPF External2 routes. It will be non-applicable, when source protocol is other than ospf.
INT agentRipRouteRedistMatchNSSAExternal1	1.3.6.1.4.1.4413.1.1.2.3.8.1.8	INTEGER	read-write	If this flag is true, RIP redistributes OSPF NSSA-External1 routes. It will be non-applicable, when source protocol is other than ospf.
INT agentRipRouteRedistMatchNSSAExternal2	1.3.6.1.4.1.4413.1.1.2.3.8.1.9	INTEGER	read-write	If this flag is true, RIP redistributes OSPF NSSA-External2 routes. It will be non-applicable, when source protocol is other than ospf.
U32 agentRipRouteRedistDistList	1.3.6.1.4.1.4413.1.1.2.3.8.1.10	Unsigned32	read-write	Access-list number of the access-list, which filters routes received from a source-protocol. A value of 0 indicates no distribute list is configured.
T/F agentRipRouteRedistDistListConfigured	1.3.6.1.4.1.4413.1.1.2.3.8.1.11	TruthValue	read-write	Flag to determine whether Access-list is configured or not.
agentRip2IfConfTable	1.3.6.1.4.1.4413.1.1.2.3.9		not-accessible	A list of subnets which require separate configuration in RIP. Augments rip2IfConfTable in the RIPv2-MIB.
agentRip2IfConfEntry	1.3.6.1.4.1.4413.1.1.2.3.9.1		not-accessible	A Single Routing Domain in a single Subnet. Augments rip2IfConfEntry in RIPv2-MIB.
INT agentRip2IfConfAuthKeyId	1.3.6.1.4.1.4413.1.1.2.3.9.1.1	INTEGER	read-create	The identifier for the authentication key used on this interface. This field is only meaningful when the RIPv2-MIB rip2IfConfAuthType is md5(3); otherwise, the value is not used.
INT agentRouterRipRoutePref	1.3.6.1.4.1.4413.1.1.2.3.10	INTEGER	read-create	The route preference, sometimes called administrative distance, for RIP routes. A route with a preference of 255 is considered unreachable.
agentRouterOspfConfigGroup	1.3.6.1.4.1.4413.1.1.2.4
I32 agentOspfDefaultMetric	1.3.6.1.4.1.4413.1.1.2.4.1	Integer32	read-write	Default metric of redistributed routes, when OSPF redistributes from other protocols. {0} indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..16777214).
T/F agentOspfDefaultMetricConfigured	1.3.6.1.4.1.4413.1.1.2.4.2	TruthValue	read-write	Flag to determine whether OSPF default-metric is configured or not. Set to 'false' to unconfigure the OSPF default-metric. Set to 'true' is not allowed.
T/F agentOspfDefaultInfoOriginate	1.3.6.1.4.1.4413.1.1.2.4.3	TruthValue	read-write	Flag to determine, whether OSPF can advertise a default-route learned from another protocol.
T/F agentOspfDefaultInfoOriginateAlways	1.3.6.1.4.1.4413.1.1.2.4.4	TruthValue	read-write	When this flag is true, the router advertises 0.0.0.0/0.0.0.0 always. Without this option, OSPF will only advertise 0.0.0.0/0.0.0.0 if the router's forwarding table contains a default route.
I32 agentOspfDefaultInfoOriginateMetric	1.3.6.1.4.1.4413.1.1.2.4.5	Integer32	read-write	Metric of the default route, which OSPF advertises when learned from other protocol. (0) indicates that the parameter is not configured, this value should not be set. Valid range for set is (1..16777214).
T/F agentOspfDefaultInfoOriginateMetricConfigured	1.3.6.1.4.1.4413.1.1.2.4.6	TruthValue	read-write	Flag to determine whether OSPF default-info originate metric is configured or not. Setting to false unconfigures the default route metric. Setting to true is not allowed.
INT agentOspfDefaultInfoOriginateMetricType	1.3.6.1.4.1.4413.1.1.2.4.7	INTEGER	read-write	Metric Type of the default route,which OSPF advertises when learned from other protocol. It can be 1(external type 1) or 2(external type 2).
agentOspfRouteRedistTable	1.3.6.1.4.1.4413.1.1.2.4.8		not-accessible	This table contains the MIB objects required to configure route-redistribution for OSPF. Here, OSPF is the Destination protocol and the source protocols can be any of : BGP, RIP, Static, Connected.
agentOspfRouteRedistEntry	1.3.6.1.4.1.4413.1.1.2.4.8.1		not-accessible
INT agentOspfRouteRedistSource	1.3.6.1.4.1.4413.1.1.2.4.8.1.1	INTEGER	read-only	Source protocol, from which OSPF can redistribute routes. This object also acts as the identifier for the OSPF redistribution Table entry.
INT agentOspfRouteRedistMode	1.3.6.1.4.1.4413.1.1.2.4.8.1.2	INTEGER	read-write	User enabels/disables route-redistribution for a particular source protocol.
I32 agentOspfRouteRedistMetric	1.3.6.1.4.1.4413.1.1.2.4.8.1.3	Integer32	read-write	Metric used for redistributing a particular source protocol route into OSPF.
T/F agentOspfRouteRedistMetricConfigured	1.3.6.1.4.1.4413.1.1.2.4.8.1.4	TruthValue	read-write	Flag to determine whether OSPF redistribute-metric is configured or not.
INT agentOspfRouteRedistMetricType	1.3.6.1.4.1.4413.1.1.2.4.8.1.5	INTEGER	read-write	Metric Type of routes,which OSPF redistributes from other source protocols. It can be 1(external type 1) or 2(external type 2).
U32 agentOspfRouteRedistTag	1.3.6.1.4.1.4413.1.1.2.4.8.1.6	Unsigned32	read-write	It specifies the tag field in routes redistributed by OSPF.
T/F agentOspfRouteRedistSubnets	1.3.6.1.4.1.4413.1.1.2.4.8.1.7	TruthValue	read-write	If this value is false, then OSPF will not redistribute subnetted routes.
U32 agentOspfRouteRedistDistList	1.3.6.1.4.1.4413.1.1.2.4.8.1.8	Unsigned32	read-write	Access-list number of the access-list, which filters routes received from a source-protocol.
T/F agentOspfRouteRedistDistListConfigured	1.3.6.1.4.1.4413.1.1.2.4.8.1.9	TruthValue	read-write	Flag to determine whether Access-list is configured or not.
agentOspfIfTable	1.3.6.1.4.1.4413.1.1.2.4.9		not-accessible	The OSPF Interface Table describes the inter- faces from the viewpoint of OSPF. Augments ospfIfTable from the OSPF-MIB.
agentOspfIfEntry	1.3.6.1.4.1.4413.1.1.2.4.9.1		not-accessible	The OSPF Interface Entry describes one inter- face from the viewpoint of OSPF. Augments ospfIfEntry in OSPF-MIB.
INT agentOspfIfAuthKeyId	1.3.6.1.4.1.4413.1.1.2.4.9.1.1	INTEGER	read-create	The identifier for the authentication key used on this interface. This field is only meaningful when the OSPF-MIB ospfIfAuthType is md5(2); otherwise, the value is not used.
INT agentOspfIfIpMtuIgnoreFlag	1.3.6.1.4.1.4413.1.1.2.4.9.1.2	INTEGER	read-write	Configures the IP MTU Ignore Flag value for this OSPF interface.
T/F agentOspfIfPassiveMode	1.3.6.1.4.1.4413.1.1.2.4.9.1.3	TruthValue	read-write	Flag to determine whether the interface is passive. A passive interface will not participate in the OSPF adjacency formation.
INT agentOspfIfAdvertiseSecondaries	1.3.6.1.4.1.4413.1.1.2.4.9.1.4	INTEGER	read-write	Configures the advertisability of the secondary addresses configured on this interface.
agentOspfVirtIfTable	1.3.6.1.4.1.4413.1.1.2.4.10		not-accessible	Information about this router's virtual inter- faces. Augments ospfVirtIfTable from the OSPF-MIB.
agentOspfVirtIfEntry	1.3.6.1.4.1.4413.1.1.2.4.10.1		not-accessible	Information about a single Virtual Interface. Augments ospfVirtIfEntry in OSPF-MIB.
INT agentOspfVirtIfAuthKeyId	1.3.6.1.4.1.4413.1.1.2.4.10.1.1	INTEGER	read-create	The identifier for the authentication key used on this virtual interface. This field is only meaningful when the OSPF-MIB ospfVirtIfAuthType is md5(2); otherwise, the value is not used.
INT agentRouterOspfRFC1583CompatibilityMode	1.3.6.1.4.1.4413.1.1.2.4.11	INTEGER	read-write	From RFC2328: Controls the preference rules used in Section 16.4 when choosing among multiple AS-external-LSAs advertising the same destination. When set to 'enabled', the preference rules remain those specified by RFC 1583 ([Ref9]). When set to 'disabled', the preference rules are those stated in Section 16.4.1, which prevent routing loops when AS- external-LSAs for the same destination have been originated from different areas. Set to 'enabled' by default. In order to minimize the chance of routing loops, all OSPF routers in an OSPF routing domain should have RFC1583Compatibility set identically. When there are routers present that have not been updated with the functionality specified in Section 16.4.1 of this memo, all routers should have RFC1583Compatibility set to 'enabled'. Otherwise, all routers should have RFC1583Compatibility set to 'disabled', preventing all routing loops.
SPF agentOspfSpfDelayTime	1.3.6.1.4.1.4413.1.1.2.4.12	SpfTimerRange	read-write	Delay time (in seconds) between when OSPF receives a topology change and when it starts an SPF calculation. It can be an integer from 0 to 65535. The default time is 5 seconds. A value of 0 means that there is no delay; that is, the SPF calculation is started immediately.
SPF agentOspfSpfHoldTime	1.3.6.1.4.1.4413.1.1.2.4.13	SpfTimerRange	read-write	Minimum time (in seconds) between two consecutive SPF calculations. It can be an integer from 0 to 65535. The default time is 10 seconds. A value of 0 means that there is no delay; that is, two SPF calculations can be done, one immediately after the other.
AUT agentOspfAutoCostRefBw	1.3.6.1.4.1.4413.1.1.2.4.14	AutoCostRefBw	read-write	Auto cost refernece bandwidth of the router interafaces for ospf metric calculations. It can be an integer from 1 to 4294967. The default reference bandwidth is 100 Mbps.
T/F agentOspfOpaqueLsaSupport	1.3.6.1.4.1.4413.1.1.2.4.15	TruthValue	read-write	The router's support for Opaque LSA types. This object is persistent and when written the entity SHOULD save the change to non-volatile storage.
agentOspfAreaOpaqueLsdbTable	1.3.6.1.4.1.4413.1.1.2.4.16		not-accessible	The OSPF Process's Area Link State Database (LSDB). The LSDB contains type-10 Link State Advertisements from throughout the areas that the device is attached to.
agentOspfAreaOpaqueLsdbEntry	1.3.6.1.4.1.4413.1.1.2.4.16.1		not-accessible	A single AreaOpaque Link State Advertisement.
IP agentOspfAreaOpaqueLsdbAreaId	1.3.6.1.4.1.4413.1.1.2.4.16.1.1	IpAddress	read-only	The 32 bit identifier of the Area from which the LSA was received.
INT agentOspfAreaOpaqueLsdbType	1.3.6.1.4.1.4413.1.1.2.4.16.1.2	INTEGER	read-only	The type of the link state advertisement. Each link state type has a separate advertisement format.
IP agentOspfAreaOpaqueLsdbLsid	1.3.6.1.4.1.4413.1.1.2.4.16.1.3	IpAddress	read-only	The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
IP agentOspfAreaOpaqueLsdbRouterId	1.3.6.1.4.1.4413.1.1.2.4.16.1.4	IpAddress	read-only	The 32 bit number that uniquely identifies the originating router in the Autonomous System.
I32 agentOspfAreaOpaqueLsdbSequence	1.3.6.1.4.1.4413.1.1.2.4.16.1.5	Integer32	read-only	The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
I32 agentOspfAreaOpaqueLsdbAge	1.3.6.1.4.1.4413.1.1.2.4.16.1.6	Integer32	read-only	This field is the age of the link state advertisement in seconds.
I32 agentOspfAreaOpaqueLsdbChecksum	1.3.6.1.4.1.4413.1.1.2.4.16.1.7	Integer32	read-only	This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connectionless datagrams; it is commonly referred to as the Fletcher checksum.
OCT agentOspfAreaOpaqueLsdbAdvertisement	1.3.6.1.4.1.4413.1.1.2.4.16.1.8	OCTET STRING	read-only	The entire Link State Advertisement, including its header. Note that for variable length LSAs, SNMP agents may not be able to return the largest string size
agentOspfLocalLsdbTable	1.3.6.1.4.1.4413.1.1.2.4.17		not-accessible	The OSPF Process's Link-Local Link State Database for non-virtual links. This table is identical to the OSPF LSDB Table in format, but contains only Link-Local Link State Advertisements for non-virtual links. The purpose is to allow Link-Local LSAs to be displayed for each non-virtual interface. This table is implemented to support type-9 LSAs which are defined in 'The OSPF Opaque LSA Option'.
agentOspfLocalLsdbEntry	1.3.6.1.4.1.4413.1.1.2.4.17.1		not-accessible	A single Link State Advertisement.
IP agentOspfLocalLsdbIpAddress	1.3.6.1.4.1.4413.1.1.2.4.17.1.1	IpAddress	read-only	The IP Address of the interface from which the LSA was received if the interface is numbered.
NUM agentOspfLocalLsdbAddressLessIf	1.3.6.1.4.1.4413.1.1.2.4.17.1.2	InterfaceIndexOrZero	read-only	The Interface Index of the interface from which the LSA was received if the interface is unnumbered.
INT agentOspfLocalLsdbType	1.3.6.1.4.1.4413.1.1.2.4.17.1.3	INTEGER	read-only	The type of the link state advertisement. Each link state type has a separate advertise- ment format.
IP agentOspfLocalLsdbLsid	1.3.6.1.4.1.4413.1.1.2.4.17.1.4	IpAddress	read-only	The Link State ID is an LS Type Specific field containing a 32 bit identifier in IP address format; it identifies the piece of the routing domain that is being described by the advertisement.
ROU agentOspfLocalLsdbRouterId	1.3.6.1.4.1.4413.1.1.2.4.17.1.5	RouterID	read-only	The 32 bit number that uniquely identifies the originating router in the Autonomous System.
I32 agentOspfLocalLsdbSequence	1.3.6.1.4.1.4413.1.1.2.4.17.1.6	Integer32	read-only	The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
I32 agentOspfLocalLsdbAge	1.3.6.1.4.1.4413.1.1.2.4.17.1.7	Integer32	read-only	This field is the age of the link state adver- tisement in seconds.
I32 agentOspfLocalLsdbChecksum	1.3.6.1.4.1.4413.1.1.2.4.17.1.8	Integer32	read-only	This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
OCT agentOspfLocalLsdbAdvertisement	1.3.6.1.4.1.4413.1.1.2.4.17.1.9	OCTET STRING	read-only	The entire Link State Advertisement, including its header. Note that for variable length LSAs, SNMP agents may not be able to return the largest string size.
agentOspfAsLsdbTable	1.3.6.1.4.1.4413.1.1.2.4.18		not-accessible	The OSPF Process's AS-scope LSA Link State Database. The Database contains the AS-scope Link State Advertisements from throughout the areas that the device is attached to. This table is identical to the OSPF LSDB Table in format, but contains only AS-scope Link State Advertisements. The purpose is to allow AS-scope LSAs to be displayed once for the router rather than once in each non-stub area.
agentOspfAsLsdbEntry	1.3.6.1.4.1.4413.1.1.2.4.18.1		not-accessible	A single Link State Advertisement.
INT agentOspfAsLsdbType	1.3.6.1.4.1.4413.1.1.2.4.18.1.1	INTEGER	read-only	The type of the link state advertisement. Each link state type has a separate advertise- ment format.
IP agentOspfAsLsdbLsid	1.3.6.1.4.1.4413.1.1.2.4.18.1.2	IpAddress	read-only	The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.
ROU agentOspfAsLsdbRouterId	1.3.6.1.4.1.4413.1.1.2.4.18.1.3	RouterID	read-only	The 32 bit number that uniquely identifies the originating router in the Autonomous System.
I32 agentOspfAsLsdbSequence	1.3.6.1.4.1.4413.1.1.2.4.18.1.4	Integer32	read-only	The sequence number field is a signed 32-bit integer. It starts with the value '80000001'h, or -'7FFFFFFF'h, and increments until '7FFFFFFF'h. Thus, a typical sequence number will be very negative. It is used to detect old and duplicate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number the more recent the advertisement.
I32 agentOspfAsLsdbAge	1.3.6.1.4.1.4413.1.1.2.4.18.1.5	Integer32	read-only	This field is the age of the link state adver- tisement in seconds.
I32 agentOspfAsLsdbChecksum	1.3.6.1.4.1.4413.1.1.2.4.18.1.6	Integer32	read-only	This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checksum. The checksum used is the same that is used for ISO connec- tionless datagrams; it is commonly referred to as the Fletcher checksum.
OCT agentOspfAsLsdbAdvertisement	1.3.6.1.4.1.4413.1.1.2.4.18.1.7	OCTET STRING	read-only	The entire Link State Advertisement, including its header.
T/F agentOspfDefaultPassiveMode	1.3.6.1.4.1.4413.1.1.2.4.19	TruthValue	read-write	Flag to determine, whether all the interfaces are passive interfaces by default. A passive interface will not participate in the OSPF adjacency formation.
INT agentOspfRoutePrefIntraArea	1.3.6.1.4.1.4413.1.1.2.4.20	INTEGER	read-write	The route preference, sometimes called administrative distance, for intra-area OSPFv2 routes. A route with a preference of 255 is considered unreachable.
INT agentOspfRoutePrefInterArea	1.3.6.1.4.1.4413.1.1.2.4.21	INTEGER	read-write	The route preference, sometimes called administrative distance, for inter-area OSPFv2 routes. A route with a preference of 255 is considered unreachable.
INT agentOspfRoutePrefExternal	1.3.6.1.4.1.4413.1.1.2.4.22	INTEGER	read-write	The route preference, sometimes called administrative distance, for external OSPFv2 routes. A route with a preference of 255 is considered unreachable.
agentSnmpTrapFlagsConfigGroupLayer3	1.3.6.1.4.1.4413.1.1.2.5
INT agentSnmpVRRPNewMasterTrapFlag	1.3.6.1.4.1.4413.1.1.2.5.1	INTEGER	read-write	This flag enables the sending of VRRP new master notification traps.
INT agentSnmpVRRPAuthFailureTrapFlag	1.3.6.1.4.1.4413.1.1.2.5.2	INTEGER	read-write	This flag enables the sending of VRRP authentication failure notification traps.
agentBootpDhcpRelayGroup	1.3.6.1.4.1.4413.1.1.2.6
I32 agentBootpDhcpRelayMaxHopCount	1.3.6.1.4.1.4413.1.1.2.6.1	Integer32	read-write	The BOOTP/DHCP Max Hop Count. The relay agent silently discards BOOTREQUEST messages whose hops field exceeds the value 16 assuming that the request is looped through the intermediate agents. The default value is 4.
IP agentBootpDhcpRelayForwardingIp	1.3.6.1.4.1.4413.1.1.2.6.2	IpAddress	read-write	DHCP server addresses are now configured through IP helper.
INT agentBootpDhcpRelayForwardMode	1.3.6.1.4.1.4413.1.1.2.6.3	INTEGER	read-write	The DHCP relay admin mode is replaced by the IP helper admin mode.
I32 agentBootpDhcpRelayMinWaitTime	1.3.6.1.4.1.4413.1.1.2.6.4	Integer32	read-write	The BOOTP/DHCP Minimum Wait Time. When the BOOTP relay agent receives a BOOTREQUEST message, it MAY use the value of the 'secs' (seconds since client began booting) field of the request as a factor in deciding whether to relay the request or not.
INT agentBootpDhcpRelayCircuitIdOptionMode	1.3.6.1.4.1.4413.1.1.2.6.5	INTEGER	read-write	The BOOTP/DHCP Circuit ID Option Mode. This flag is set to enable/disable the network element to add/remove the DHCP Relay agent Circuit ID sub-options.
I32 agentBootpDhcpRelayNumOfRequestsReceived	1.3.6.1.4.1.4413.1.1.2.6.6	Integer32	read-only	Replaced by IP helper statistics.
I32 agentBootpDhcpRelayNumOfRequestsForwarded	1.3.6.1.4.1.4413.1.1.2.6.7	Integer32	read-only	Replaced by IP helper statistics.
I32 agentBootpDhcpRelayNumOfDiscards	1.3.6.1.4.1.4413.1.1.2.6.8	Integer32	read-only	Replaced by IP helper statistics.
agentECMPGroup	1.3.6.1.4.1.4413.1.1.2.7
I32 agentECMPOspfMaxPaths	1.3.6.1.4.1.4413.1.1.2.7.1	Integer32	read-write	It sets the number of paths that OSPF can report for a given destination where maxpaths is platform-dependent.
agentRouterVrrpConfigGroup	1.3.6.1.4.1.4413.1.1.2.8
INT agentRouterVrrpAdminState	1.3.6.1.4.1.4413.1.1.2.8.1	INTEGER	read-write	Sets the administrative mode of VRRP in the router.
agentRouterVrrpConfiguredTable	1.3.6.1.4.1.4413.1.1.2.8.2		not-accessible	Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of `agentRouterVrrpConfiguredEntry' items.
agentRouterVrrpConfiguredEntry	1.3.6.1.4.1.4413.1.1.2.8.2.1		not-accessible	An entry in the table contains operational priority that is associated with a virtual router.
I32 agentRouterVrrpConfiguredPriority	1.3.6.1.4.1.4413.1.1.2.8.2.1.1	Integer32	read-only	This object specifies the value set by the vrrpOperPriority object. The GET operation on 'vrrpOperPriority' will be affected by both the tracking process and the configured priority set by the vrrpOperPriority object.
agentVrrpOperations	1.3.6.1.4.1.4413.1.1.2.9
agentRouterVrrpOperTable	1.3.6.1.4.1.4413.1.1.2.9.1		not-accessible	Operations table for a VRRP router which consists of a sequence (i.e., one or more conceptual rows) of `agentRouterVrrpOperEntry' items.
agentRouterVrrpOperEntry	1.3.6.1.4.1.4413.1.1.2.9.1.1		not-accessible	An entry in the table contains operational priority that is associated with a virtual router.
I32 agentRouterVrrpOperPriority	1.3.6.1.4.1.4413.1.1.2.9.1.1.1	Integer32	read-only	This object specifies the operational priority of the VRRP router. This value will be afftected by both the tracking process and the configured priority set by the vrrpOperPriority object.
agentRouterVrrpTrackGroup	1.3.6.1.4.1.4413.1.1.2.10
agentRouterVrrpTrackIntfTable	1.3.6.1.4.1.4413.1.1.2.10.1		not-accessible	Tracking table for a VRRP router which consists of agentRouterVrrpTrackIntfEntry items.
agentRouterVrrpTrackIntfEntry	1.3.6.1.4.1.4413.1.1.2.10.1.1		not-accessible	An entry in the table contains tracked IP interfaces associated with a virtual router.
NUM agentRouterVrrpTrackIntf	1.3.6.1.4.1.4413.1.1.2.10.1.1.1	InterfaceIndex	read-create	This object specifies the interface to be tracked.
I32 agentRouterVrrpTrackIfPrioDec	1.3.6.1.4.1.4413.1.1.2.10.1.1.2	Integer32	read-create	This object specifies the decrement priority of the VRRP router.
T/F agentRouterVrrpTrackIfState	1.3.6.1.4.1.4413.1.1.2.10.1.1.3	TruthValue	read-only	This object specifies the IP state of the tracked interface for the virtual router.
ROW agentRouterVrrpTrackIfStatus	1.3.6.1.4.1.4413.1.1.2.10.1.1.4	RowStatus	read-create	The row status variable, used in accordance to installation and removal conventions for conceptual rows. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). The newly created row will be in active state later. To destroy the row set this object to destroy.
agentRouterVrrpTrackRouteTable	1.3.6.1.4.1.4413.1.1.2.10.2		not-accessible	Tracking table for a VRRP router which consists of a 'agentRouterVrrpTrackRouteEntry' items.
agentRouterVrrpTrackRouteEntry	1.3.6.1.4.1.4413.1.1.2.10.2.1		not-accessible	An entry in the table contains tracked Routes associated with a virtual router.
IP agentRouterVrrpTrackRtPfx	1.3.6.1.4.1.4413.1.1.2.10.2.1.1	IpAddress	not-accessible	This object specifies the prefix of the route to be tracked.
I32 agentRouterVrrpTrackRtPfxLen	1.3.6.1.4.1.4413.1.1.2.10.2.1.2	Integer32	not-accessible	This object specifies prefix length of the route to be tracked.
I32 agentRouterVrrpTrackRtPrioDec	1.3.6.1.4.1.4413.1.1.2.10.2.1.3	Integer32	read-create	This object specifies the decrement priority of the VRRP router.
T/F agentRouterVrrpTrackRtReachable	1.3.6.1.4.1.4413.1.1.2.10.2.1.4	TruthValue	read-only	This object specifies the reachability of the tracked route.
ROW agentRouterVrrpTrackRtStatus	1.3.6.1.4.1.4413.1.1.2.10.2.1.5	RowStatus	read-create	The row status variable, used in accordance to installation and removal conventions for conceptual rows. To create a row in this table, a manager sets this object to either createAndGo(4) or createAndWait(5). The newly created row will be in active state later. To delete the tracked route set this object to destroy.
agentIpHelperGroup	1.3.6.1.4.1.4413.1.1.2.11
INT agentIpHelperAdminMode	1.3.6.1.4.1.4413.1.1.2.11.1	INTEGER	read-write	Administratively enable or disable IP helper.
C32 agentDhcpClientMsgsReceivedEx	1.3.6.1.4.1.4413.1.1.2.11.2	Counter32	read-only	The Number of DHCP Requests Received. Total number of DHCP requests received from all clients.
C32 agentDhcpClientMsgsRelayed	1.3.6.1.4.1.4413.1.1.2.11.3	Counter32	read-only	The Number of DHCP Requests Forwarded. Total number of DHCP requests relayed to a server.
C32 agentDhcpServerMsgsReceived	1.3.6.1.4.1.4413.1.1.2.11.4	Counter32	read-only	The number of DHCP messages received from a server.
C32 agentDhcpServerMsgsRelayed	1.3.6.1.4.1.4413.1.1.2.11.5	Counter32	read-only	The number of DHCP messages relayed to a server.
C32 agentUdpClientMsgsReceived	1.3.6.1.4.1.4413.1.1.2.11.6	Counter32	read-only	The number of UDP messages received from all clients.
C32 agentUdpClientMsgsRelayed	1.3.6.1.4.1.4413.1.1.2.11.7	Counter32	read-only	The number of UDP messages relayed to a server.
agentSwitchIpHelperAddressTable	1.3.6.1.4.1.4413.1.1.2.11.8		not-accessible	Contains a list of IP helper addresses configured globally.
agentSwitchIpHelperAddressEntry	1.3.6.1.4.1.4413.1.1.2.11.8.1		not-accessible	An IP Helper address that applies to packets received on any interface.
IP agentSwitchIpHelperAddress	1.3.6.1.4.1.4413.1.1.2.11.8.1.1	IpAddress	read-write	The IP Helper address assigned to this interface.
U32 agentSwitchIpHelperUdpPort	1.3.6.1.4.1.4413.1.1.2.11.8.1.2	Unsigned32	read-write	UDP port number.
U32 agentSwitchIpHelperHitCount	1.3.6.1.4.1.4413.1.1.2.11.8.1.3	Unsigned32	read-only	The number of times a packet has been forwarded or discarded according to this entry.
ROW agentSwitchIpHelperStatus	1.3.6.1.4.1.4413.1.1.2.11.8.1.4	RowStatus	read-create	Creates a new entry in the global IP Helper address table. Allowed values are: createAndGo(4) - Creates an IP helper entry in this table. destroy(6) - Removes the IP helper entry.
C32 agentUdpClientMsgsTtlExpired	1.3.6.1.4.1.4413.1.1.2.11.9	Counter32	read-only	The number of UDP messages received with an expired TTL.
C32 agentUdpClientMsgsDiscarded	1.3.6.1.4.1.4413.1.1.2.11.10	Counter32	read-only	The number of UDP messages that matched a discard entry.
agentInternalVlanGroup	1.3.6.1.4.1.4413.1.1.2.12
I32 agentInternalVlanBase	1.3.6.1.4.1.4413.1.1.2.12.1	Integer32	read-write	The VLAN ID internally assigned to the first port-based routing interface.
INT agentInternalVlanPolicy	1.3.6.1.4.1.4413.1.1.2.12.2	INTEGER	read-write	Whether to search up or down from the base VLAN ID for a free VLAN ID to assign to a port-based routing interface.
agentSwitchInternalVlanTable	1.3.6.1.4.1.4413.1.1.2.12.3		not-accessible	Contains a list of VLAN IDs used internally for port-based routing interfaces.
agentSwitchInternalVlanEntry	1.3.6.1.4.1.4413.1.1.2.12.3.1		not-accessible	A VLAN ID internally assigned to a port-based routing interface.
I32 agentSwitchInternalVlanId	1.3.6.1.4.1.4413.1.1.2.12.3.1.1	Integer32	not-accessible	A VLAN ID internally assigned to a port-based routing interface.
I32 agentSwitchInternalVlanIfIndex	1.3.6.1.4.1.4413.1.1.2.12.3.1.2	Integer32	read-only	Interface index of port-based routing interface using this VLAN ID.
agentOspfQueueGroup	1.3.6.1.4.1.4413.1.1.2.13
agentOspfQueueTable	1.3.6.1.4.1.4413.1.1.2.13.1		not-accessible	Table lists information about OSPFv2 message queue utilization.
agentOspfQueueEntry	1.3.6.1.4.1.4413.1.1.2.13.1.1		not-accessible	Information on a specific OSPFv2 message queue.
U32 agentOspfQueueIndex	1.3.6.1.4.1.4413.1.1.2.13.1.1.1	Unsigned32	not-accessible	Index value for this message queue.
STR agentOspfQueueName	1.3.6.1.4.1.4413.1.1.2.13.1.1.2	DisplayString	read-only	Name of an OSPFv2 message queue.
G32 agentOspfQueueLength	1.3.6.1.4.1.4413.1.1.2.13.1.1.3	Gauge32	read-only	The number of messages currently in the message queue.
G32 agentOspfQueueHigh	1.3.6.1.4.1.4413.1.1.2.13.1.1.4	Gauge32	read-only	The high water mark of the number of messages in the message queue.
C32 agentOspfQueueDrops	1.3.6.1.4.1.4413.1.1.2.13.1.1.5	Counter32	read-only	The number of items dropped because the message queue was full.
U32 agentOspfQueueLimit	1.3.6.1.4.1.4413.1.1.2.13.1.1.6	Unsigned32	read-only	The maximum number of messages this queue can hold.
agentOspfPacketStatsGroup	1.3.6.1.4.1.4413.1.1.2.14
U32 agentOspfCountersCleared	1.3.6.1.4.1.4413.1.1.2.14.1	Unsigned32	read-only	The time since OSPFv2 counters were last cleared, in seconds.
C32 agentOspfLsaRetxCount	1.3.6.1.4.1.4413.1.1.2.14.2	Counter32	read-only	The total number of LSAs retransmitted since OSPF counters were last cleared. If the same LSA is retransmitted to multiple neighbors, the count is incremented for each neighbor.
C32 agentOspfHellosRx	1.3.6.1.4.1.4413.1.1.2.14.3	Counter32	read-only	The total number of OSPFv2 Hello packets received since OSPF counters were last cleared.
C32 agentOspfHellosTx	1.3.6.1.4.1.4413.1.1.2.14.4	Counter32	read-only	The total number of OSPFv2 Hello packets transmitted since OSPF counters were last cleared.
C32 agentOspfDdRx	1.3.6.1.4.1.4413.1.1.2.14.5	Counter32	read-only	The total number of OSPFv2 Database Description packets received since OSPF counters were last cleared.
C32 agentOspfDdTx	1.3.6.1.4.1.4413.1.1.2.14.6	Counter32	read-only	The total number of OSPFv2 Database Description packets transmitted since OSPF counters were last cleared.
C32 agentOspfLsReqRx	1.3.6.1.4.1.4413.1.1.2.14.7	Counter32	read-only	The total number of OSPFv2 LS Request packets received since OSPF counters were last cleared.
C32 agentOspfLsReqTx	1.3.6.1.4.1.4413.1.1.2.14.8	Counter32	read-only	The total number of OSPFv2 LS Request packets transmitted since OSPF counters were last cleared.
C32 agentOspfLsUpdatesRx	1.3.6.1.4.1.4413.1.1.2.14.9	Counter32	read-only	The total number of OSPFv2 LS Update packets received since OSPF counters were last cleared.
C32 agentOspfLsUpdatesTx	1.3.6.1.4.1.4413.1.1.2.14.10	Counter32	read-only	The total number of OSPFv2 LS Update packets transmitted since OSPF counters were last cleared.
C32 agentOspfLsAckRx	1.3.6.1.4.1.4413.1.1.2.14.11	Counter32	read-only	The total number of OSPFv2 LS Acknowledgement packets received since OSPF counters were last cleared.
C32 agentOspfLsAckTx	1.3.6.1.4.1.4413.1.1.2.14.12	Counter32	read-only	The total number of OSPFv2 LS Acknowledgement packets transmitted since OSPF counters were last cleared.
G32 agentOspfLsUpdatesRxMax	1.3.6.1.4.1.4413.1.1.2.14.13	Gauge32	read-only	The maximum rate of OSPFv2 LS Update packets received over any 5-second interval since OSPF counters were last cleared. The rate is given in packets per second (that is, the number of packets received during the 5-second interval, divided by 5).
G32 agentOspfLsUpdatesTxMax	1.3.6.1.4.1.4413.1.1.2.14.14	Gauge32	read-only	The maximum rate of OSPFv2 LS Update packets transmitted over any 5-second interval since OSPF counters were last cleared. The rate is given in packets per second (that is, the number of packets transmitted during the 5-second interval, divided by 5).
C32 agentOspfType1LsasRx	1.3.6.1.4.1.4413.1.1.2.14.15	Counter32	read-only	The number of type 1 (router) LSAs received since OSPF counters were last cleared.
C32 agentOspfType2LsasRx	1.3.6.1.4.1.4413.1.1.2.14.16	Counter32	read-only	The number of type 2 (network) LSAs received since OSPF counters were last cleared.
C32 agentOspfType3LsasRx	1.3.6.1.4.1.4413.1.1.2.14.17	Counter32	read-only	The number of type 3 (network summary) LSAs received since OSPF counters were last cleared.
C32 agentOspfType4LsasRx	1.3.6.1.4.1.4413.1.1.2.14.18	Counter32	read-only	The number of type 4 (ASBR summary) LSAs received since OSPF counters were last cleared.
C32 agentOspfType5LsasRx	1.3.6.1.4.1.4413.1.1.2.14.19	Counter32	read-only	The number of type 5 (external) LSAs received since OSPF counters were last cleared.
C32 agentOspfType7LsasRx	1.3.6.1.4.1.4413.1.1.2.14.20	Counter32	read-only	The number of type 7 (NSSA external) LSAs received since OSPF counters were last cleared.
C32 agentOspfType9LsasRx	1.3.6.1.4.1.4413.1.1.2.14.21	Counter32	read-only	The number of type 9 (Link Opaque) LSAs received since OSPF counters were last cleared.
C32 agentOspfType10LsasRx	1.3.6.1.4.1.4413.1.1.2.14.22	Counter32	read-only	The number of type 10 (Area Opaque) LSAs received since OSPF counters were last cleared.
C32 agentOspfType11LsasRx	1.3.6.1.4.1.4413.1.1.2.14.23	Counter32	read-only	The number of type 11 (AS Opaque) LSAs received since OSPF counters were last cleared.
agentOspfSpfStatsTable	1.3.6.1.4.1.4413.1.1.2.15		not-accessible	Contains statistics for the twenty most recent SPF runs. Statistics are reported from the oldest SPF first to the most recent.
agentOspfSpfStatsEntry	1.3.6.1.4.1.4413.1.1.2.15.1		not-accessible	Statistics for a single SPF run.
C32 agentOspfSpfIndex	1.3.6.1.4.1.4413.1.1.2.15.1.1	Counter32	not-accessible	Integer that uniquely identifies an SPF run. This value is incremented each time OSPF runs a full routing table calculation.
U32 agentOspfSpfStatsDeltaT	1.3.6.1.4.1.4413.1.1.2.15.1.2	Unsigned32	read-only	How long since this routing table calculation ran. The time is given in seconds.
G32 agentOspfSpfStatsIntra	1.3.6.1.4.1.4413.1.1.2.15.1.3	Gauge32	read-only	Number of milliseconds to compute intra-area routes.
G32 agentOspfSpfStatsSumm	1.3.6.1.4.1.4413.1.1.2.15.1.4	Gauge32	read-only	Number of milliseconds to compute inter-area routes.
G32 agentOspfSpfStatsExt	1.3.6.1.4.1.4413.1.1.2.15.1.5	Gauge32	read-only	Number of milliseconds to compute external routes.
G32 agentOspfSpfStatsSpfTotal	1.3.6.1.4.1.4413.1.1.2.15.1.6	Gauge32	read-only	Number of milliseconds for entire routing table calculation.
G32 agentOspfSpfStatsRibUpdate	1.3.6.1.4.1.4413.1.1.2.15.1.7	Gauge32	read-only	Number of milliseconds to update the common routing table.
STR agentOspfSpfStatsReason	1.3.6.1.4.1.4413.1.1.2.15.1.8	DisplayString	read-only	Reasons why a routing table calculation was required. R - new router LSA, N - new Network LSA, SN - new network summary LSA, SA - new ASBR summary LSA, X - new external LSA.
agentRoutingHeapGroup	1.3.6.1.4.1.4413.1.1.2.16
U32 agentRoutingHeapSize	1.3.6.1.4.1.4413.1.1.2.16.1	Unsigned32	read-only	The size of the routing heap, in bytes. Unicast routing protocols and ARP allocate memory from the routing heap.
G32 agentRoutingHeapInUse	1.3.6.1.4.1.4413.1.1.2.16.2	Gauge32	read-only	The number of bytes currently allocated from the routing heap.
G32 agentRoutingHeapHigh	1.3.6.1.4.1.4413.1.1.2.16.3	Gauge32	read-only	High water mark for the number of bytes allocated from the routing heap.
agentRoutingTableSummaryGroup	1.3.6.1.4.1.4413.1.1.2.17
G32 agentConnectedRoutes	1.3.6.1.4.1.4413.1.1.2.17.1	Gauge32	read-only	The number of connected routes in the IPv4 routing table.
G32 agentStaticRoutes	1.3.6.1.4.1.4413.1.1.2.17.2	Gauge32	read-only	The number of static routes in the IPv4 routing table.
G32 agentRipRoutes	1.3.6.1.4.1.4413.1.1.2.17.3	Gauge32	read-only	The number of RIP routes in the IPv4 routing table.
G32 agentOspfRoutes	1.3.6.1.4.1.4413.1.1.2.17.4	Gauge32	read-only	The number of OSPFv2 routes in the IPv4 routing table.
G32 agentOspfIntraRoutes	1.3.6.1.4.1.4413.1.1.2.17.5	Gauge32	read-only	The number of OSPFv2 intra-area routes in the IPv4 routing table.
G32 agentOspfInterRoutes	1.3.6.1.4.1.4413.1.1.2.17.6	Gauge32	read-only	The number of OSPFv2 inter-area routes in the IPv4 routing table.
G32 agentOspfExt1Routes	1.3.6.1.4.1.4413.1.1.2.17.7	Gauge32	read-only	The number of OSPFv2 external type 1 routes in the IPv4 routing table.
G32 agentOspfExt2Routes	1.3.6.1.4.1.4413.1.1.2.17.8	Gauge32	read-only	The number of OSPFv2 external type 2 routes in the IPv4 routing table.
G32 agentBgpRoutes	1.3.6.1.4.1.4413.1.1.2.17.9	Gauge32	read-only	The number of BGP routes in the IPv4 routing table.
G32 agentEbgpRoutes	1.3.6.1.4.1.4413.1.1.2.17.10	Gauge32	read-only	The number of external BGP routes in the IPv4 routing table.
G32 agentIbgpRoutes	1.3.6.1.4.1.4413.1.1.2.17.11	Gauge32	read-only	The number of internal BGP routes in the IPv4 routing table.
G32 agentLocalBgpRoutes	1.3.6.1.4.1.4413.1.1.2.17.12	Gauge32	read-only	The number of local BGP routes in the IPv4 routing table.
G32 agentRejectRoutes	1.3.6.1.4.1.4413.1.1.2.17.13	Gauge32	read-only	The number of reject routes in the IPv4 routing table.
G32 agentTotalRoutes	1.3.6.1.4.1.4413.1.1.2.17.14	Gauge32	read-only	The number of routes in the IPv4 routing table.
G32 agentBestRoutes	1.3.6.1.4.1.4413.1.1.2.17.15	Gauge32	read-only	The number of IPv4 routes in the forwarding table.
G32 agentBestRoutesHigh	1.3.6.1.4.1.4413.1.1.2.17.16	Gauge32	read-only	The highest number of IPv4 routes in the forwarding table.
G32 agentAlternateRoutes	1.3.6.1.4.1.4413.1.1.2.17.17	Gauge32	read-only	The number of alternate routes in the IPv4 routing table. An alternate route is less preferred than the best route and is not used for forwarding.
C32 agentRouteAdds	1.3.6.1.4.1.4413.1.1.2.17.18	Counter32	read-only	The number of routes added to the IPv4 routing table.
C32 agentRouteModifies	1.3.6.1.4.1.4413.1.1.2.17.19	Counter32	read-only	The number of routes changed in the IPv4 routing table.
C32 agentRouteDeletes	1.3.6.1.4.1.4413.1.1.2.17.20	Counter32	read-only	The number of routes removed from the IPv4 routing table.
C32 agentUnresolvedRouteAdds	1.3.6.1.4.1.4413.1.1.2.17.21	Counter32	read-only	The number of IPv4 route adds that failed because none of the route's next hops were on a local subnet.
C32 agentInvalidRouteAdds	1.3.6.1.4.1.4413.1.1.2.17.22	Counter32	read-only	The number of IPv4 routes adds that failed because the route was invalid.
C32 agentFailedRouteAdds	1.3.6.1.4.1.4413.1.1.2.17.23	Counter32	read-only	The number of IPv4 routes adds that failed because of a resource limitation in the routing table
G32 agentReservedLocals	1.3.6.1.4.1.4413.1.1.2.17.24	Gauge32	read-only	The number of IPv4 routing table entries reserved for a local subnet on a routing interface that is down.
G32 agentUniqueNextHops	1.3.6.1.4.1.4413.1.1.2.17.25	Gauge32	read-only	The number of distinct next hops used among all IPv4 routes currently in the routing table. These include local interfaces for local routes and neighbors for indirect routes.
G32 agentUniqueNextHopsHigh	1.3.6.1.4.1.4413.1.1.2.17.26	Gauge32	read-only	The highest count of unique next hops since counters were last cleared.
G32 agentNextHopGroups	1.3.6.1.4.1.4413.1.1.2.17.27	Gauge32	read-only	The current number of next hop groups in use by one or more routes. Each next hop group includes one or more next hops.
G32 agentNextHopGroupsHigh	1.3.6.1.4.1.4413.1.1.2.17.28	Gauge32	read-only	The highest count of next hop groups since counters were last cleared.
G32 agentEcmpGroups	1.3.6.1.4.1.4413.1.1.2.17.29	Gauge32	read-only	The number of next hop groups with multiple next hops.
G32 agentEcmpGroupsHigh	1.3.6.1.4.1.4413.1.1.2.17.30	Gauge32	read-only	The high water mark of the number of ECMP groups.
G32 agentEcmpRoutes	1.3.6.1.4.1.4413.1.1.2.17.31	Gauge32	read-only	The current number of IPv4 routes with multiple next hops.
G32 agentTruncEcmpRoutes	1.3.6.1.4.1.4413.1.1.2.17.32	Gauge32	read-only	The number of ECMP routes that are currently installed in the forwarding table with just one next hop. The forwarding table may limit the number of ECMP routes or the number of ECMP groups. When an ECMP route cannot be installed because such a limit is reached, the route is installed with a single next hop.
C32 agentEcmpRetries	1.3.6.1.4.1.4413.1.1.2.17.33	Counter32	read-only	The number of ECMP routes that have been installed in the forwarding table after initially being installed with a single next hop.
agentEcmpCountTable	1.3.6.1.4.1.4413.1.1.2.18		not-accessible	A count of the number of routes with each number of ECMP next hops.
agentEcmpCountEntry	1.3.6.1.4.1.4413.1.1.2.18.1		not-accessible	Number of IPv4 routes with a given number of next hops.
U32 agentEcmpNextHopCount	1.3.6.1.4.1.4413.1.1.2.18.1.1	Unsigned32	not-accessible	The number of next hops in a route. From 0 to the maximum number of next hops in an ECMP route. The maximum varies by platform.
G32 agentEcmpRouteCount	1.3.6.1.4.1.4413.1.1.2.18.1.2	Gauge32	read-only	The number of IPv4 routes with agentEcmpNextHopCount next hops.
agentOspfStubRouterGroup	1.3.6.1.4.1.4413.1.1.2.19
INT ospfStubRouterAdvertisement	1.3.6.1.4.1.4413.1.1.2.19.1	INTEGER	read-only	Specifies how the router LSAs are advertised by the router. The value doNotAdvertise indicates the advertisement of a standard router LSA and is the default value. The value advertise indicates the advertisement of a stub router LSA.
INT agentOspfStubRouterReason	1.3.6.1.4.1.4413.1.1.2.19.2	INTEGER	read-only	This indicates the reason because of which the router is in Stub mode. This is valid only if the agentOspfStubRouterMode is 'active'.
U32 agentOspfStubRouterStartupTimeRemaining	1.3.6.1.4.1.4413.1.1.2.19.3	Unsigned32	read-only	The time remaining (in seconds) for the router to come out of the stub mode. This is valid only if the agentOspfStubRouterReason is 'startup'.
U32 agentOspfStubRouterDuration	1.3.6.1.4.1.4413.1.1.2.19.4	Unsigned32	read-only	Time elapsed (in seconds) since the router last entered the stub router mode. This is valid only if the agentOspfStubRouterMode is 'active' and agentOspfStubRouterReason is 'resource-limitation'.

RFC description

Vendor-private MIB for Ubiquiti EdgeSwitch routing management; defines objects for route table, BGP, OSPF, and general IP routing protocol monitoring.

Start monitoring Ubiquiti EdgeSwitch (Broadcom FastPath-based) switch (IPv4 static routing/L3 forwarding) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download EdgeSwitch-ROUTING-MIB