FOUNDRY-SN-IP-MIB

All MIBs › FOUNDRY-SN-IP-MIB

Category: IP and Core Protocols, Routing Protocols, Technology: Routing, Vendor: Foundry/Brocade

Description: Brocade Foundry IP MIB providing IPv4 routing, interface, and forwarding table management objects for FastIron Layer 3 switches and routers.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is FOUNDRY-SN-IP-MIB?

FOUNDRY-SN-IP-MIB is a Brocade/Foundry proprietary MIB providing IPv4 routing, interface, and forwarding-table management for FastIron Layer 3 switches. It exposes objects for ARP aging, default TTL, proxy ARP/RARP, BOOTP relay, IRDP, and load-sharing behavior, plus commands to clear ARP/route/IP caches. Its monitoring value is centered on the software IP forwarding plane: confirming ARP timeout, TTL, load-share, and proxy-ARP settings match intent, letting an admin verify a routing change took effect as designed. It complements standard IP-MIB and IP-FORWARD-MIB objects with Foundry-specific controls. Network engineers who download FOUNDRY-SN-IP-MIB definitions typically pair them with the standard IP-MIB for a complete view of the routing plane. It is used on FastIron Layer 3 switches and routers handling IPv4 routing.

IPNetwork Monitor allows you to monitor SNMP objects defined in FOUNDRY-SN-IP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ruckus (CommScope) ICX 8200 (2023) — campus switch for wireless-first/IoT networks, current FastIron-lineage successor to Brocade Foundry FastIron
Ruckus ICX 7550 — multigig (up to 48-port) campus switch, current FastIron-based product

Monitoring Examples

snRtArpAge and snRtIpTtl reveal the current ARP timeout and default TTL configuration, while snRtIpLoadShare and snRtIpProxyArp confirm whether ECMP load sharing and proxy ARP are enabled; after a routing change, an admin polls these to confirm the intended forwarding behavior took effect, using snRtClearArpCache or snRtClearIpRoute to force a refresh if stale entries are suspected.

What Can Be Monitored

ARP aging timeout
default TTL setting
proxy ARP and RARP status
IP load-sharing state
BOOTP/DHCP relay configuration
IRDP enabled state

Imported Objects

From FOUNDRY-SN-ROOT-MIB

snDvmrp	OBJECT-IDENTITY
snFsrp	OBJECT-IDENTITY
snGblRt	OBJECT-IDENTITY
snIp	OBJECT-IDENTITY
snLoopbackIf	OBJECT-IDENTITY
snPim	OBJECT-IDENTITY
snRip	OBJECT-IDENTITY
snVrrp	OBJECT-IDENTITY

From IF-MIB

InterfaceIndex

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
IpAddress
TimeTicks

OIDs

OID symbolic	OID numeric	Type	Access	Description
IP snDvmrpDefaultRoute	1.3.6.1.4.1.1991.1.2.5.1.12	IpAddress	read-write	This is the IP address of a router that is connected to one of the directly attached subnet. If a multicast route is not present on the local router, this default route will be used for multicast forwarding. snDvmrpEnable must be 'enabled' before this object is writen.
RTR snDvmrpEnable	1.3.6.1.4.1.1991.1.2.5.1.2	RtrStatus	read-write	Enable or disable DVMRP on this router.
INT snDvmrpGenerationId	1.3.6.1.4.1.1991.1.2.5.1.3	INTEGER	read-only	The generation identifier for the routing process. This is used by neighboring routers to detect whether pruning information should be resent.
INT snDvmrpGraftRetransmitTime	1.3.6.1.4.1.1991.1.2.5.1.11	INTEGER	read-write	This is the time interval after which a graft message will be retransmitted if graft acknowledge message has not been received. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
snDvmrpMIBObjects	1.3.6.1.4.1.1991.1.2.5.1
IP snDvmrpNeighborAddress	1.3.6.1.4.1.1991.1.2.5.1.14.1.3	IpAddress	read-only	The IP address of the DVMRP neighbor for which this entry contains information.
INT snDvmrpNeighborCapabilities	1.3.6.1.4.1.1991.1.2.5.1.14.1.9	INTEGER	read-only	This object describes the neighboring router's capabilities. The following shows the position of each bit: bit position meaning ----------- ------ 3 mtrace bit 2 generationID bit 1 prune bit 0 leaf bit The leaf bit indicates that the neighbor has only one interface with neighbors. The prune bit indicates that the neighbor supports pruning. The generationID bit indicates that the neighbor sends its generationID in Probe messages. The mtrace bit indicates that the neighbor can handle mtrace requests.
snDvmrpNeighborEntry	1.3.6.1.4.1.1991.1.2.5.1.14.1		not-accessible	An entry (conceptual row) in the snDvmrpNeighborTable.
INT snDvmrpNeighborEntryIndex	1.3.6.1.4.1.1991.1.2.5.1.14.1.1	INTEGER	read-only	The table entry index.
TIK snDvmrpNeighborExpiryTime	1.3.6.1.4.1.1991.1.2.5.1.14.1.5	TimeTicks	read-only	The minimum time remaining before this DVMRP neighbor will be aged out.
INT snDvmrpNeighborGenerationId	1.3.6.1.4.1.1991.1.2.5.1.14.1.6	INTEGER	read-only	The neighboring router's generation identifier.
INT snDvmrpNeighborMajorVersion	1.3.6.1.4.1.1991.1.2.5.1.14.1.7	INTEGER	read-only	The neighboring router's major DVMRP version number.
INT snDvmrpNeighborMinorVersion	1.3.6.1.4.1.1991.1.2.5.1.14.1.8	INTEGER	read-only	The neighboring router's minor DVMRP version number.
INT snDvmrpNeighborRouterTimeout	1.3.6.1.4.1.1991.1.2.5.1.7	INTEGER	read-write	This is the time interval after which the neighbour router is considered down. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
snDvmrpNeighborTable	1.3.6.1.4.1.1991.1.2.5.1.14		not-accessible	The (conceptual) table listing the router's DVMRP neighbors, as discovered by receiving Neighbor Probe messages. snDvmrpEnable must be 'enabled' before this table is read.
TIK snDvmrpNeighborUpTime	1.3.6.1.4.1.1991.1.2.5.1.14.1.4	TimeTicks	read-only	The time since this DVMRP neighbor (last) became a neighbor of the local router.
INT snDvmrpNeighborVifIndex	1.3.6.1.4.1.1991.1.2.5.1.14.1.2	INTEGER	read-only	The value of VifIndex for the virtual interface used to reach this DVMRP neighbor.
INT snDvmrpProbeInterval	1.3.6.1.4.1.1991.1.2.5.1.4	INTEGER	read-write	This is the time interval at which the router sends out probe messages to discover neighbour routers. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
INT snDvmrpPruneAge	1.3.6.1.4.1.1991.1.2.5.1.10	INTEGER	read-write	This is the duration of time for which the prune state is stored. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
INT snDvmrpReportInterval	1.3.6.1.4.1.1991.1.2.5.1.5	INTEGER	read-write	This is the time interval at which the router sends out full report messages. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
INT snDvmrpRouteDiscardTime	1.3.6.1.4.1.1991.1.2.5.1.9	INTEGER	read-write	This is the time interval after which a route is discarded from the route table. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
snDvmrpRouteEntry	1.3.6.1.4.1.1991.1.2.5.1.15.1		not-accessible	An entry (conceptual row) containing the multicast routing information used by DVMRP in place of the unicast routing information.
INT snDvmrpRouteEntryIndex	1.3.6.1.4.1.1991.1.2.5.1.15.1.1	INTEGER	read-only	The table entry index.
INT snDvmrpRouteExpireTime	1.3.6.1.4.1.1991.1.2.5.1.8	INTEGER	read-write	This is the time interval after which the route expires and becomes unreachable. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
TIK snDvmrpRouteExpiryTime	1.3.6.1.4.1.1991.1.2.5.1.15.1.7	TimeTicks	read-only	The minimum amount of time remaining before this entry will be aged out.
INT snDvmrpRouteMetric	1.3.6.1.4.1.1991.1.2.5.1.15.1.6	INTEGER	read-only	The distance in hops to the source subnet.
snDvmrpRouteNextHopEntry	1.3.6.1.4.1.1991.1.2.5.1.16.1		not-accessible	An entry (conceptual row) in the list of next hops on outgoing interfaces to which IP multicast datagrams from particular sources are routed.
IP snDvmrpRouteNextHopSource	1.3.6.1.4.1.1991.1.2.5.1.16.1.1	IpAddress	read-only	The network address which when combined with the corresponding value of snDvmrpRouteNextHopSourceMask identifies the sources for which this entry specifies a next hop on an outgoing interface.
IP snDvmrpRouteNextHopSourceMask	1.3.6.1.4.1.1991.1.2.5.1.16.1.2	IpAddress	read-only	The network mask which when combined with the corresponding value of snDvmrpRouteNextHopSource identifies the sources for which this entry specifies a next hop on an outgoing interface.
snDvmrpRouteNextHopTable	1.3.6.1.4.1.1991.1.2.5.1.16		not-accessible	The (conceptual) table containing information on the next hops on outgoing interfaces for routing IP multicast datagrams. snDvmrpEnable must be 'enabled' before this table is read.
INT snDvmrpRouteNextHopType	1.3.6.1.4.1.1991.1.2.5.1.16.1.4	INTEGER	read-only	Type is leaf if no neighbors exist on the outgoing virtual interface. Otherwise, type is branch.
INT snDvmrpRouteNextHopVifIndex	1.3.6.1.4.1.1991.1.2.5.1.16.1.3	INTEGER	read-only	The snDvmrpVInterfaceVifIndex value of the virtual interface for the outgoing interface for this next hop.
IP snDvmrpRouteSource	1.3.6.1.4.1.1991.1.2.5.1.15.1.2	IpAddress	read-only	The network address which when combined with the corresponding value of snDvmrpRouteSourceMask identifies the sources for which this entry contains multicast routing information.
IP snDvmrpRouteSourceMask	1.3.6.1.4.1.1991.1.2.5.1.15.1.3	IpAddress	read-only	The network mask which when combined with the corresponding value of snDvmrpRouteSource identifies the sources for which this entry contains multicast routing information.
snDvmrpRouteTable	1.3.6.1.4.1.1991.1.2.5.1.15		not-accessible	The routing table used by DVMRP in place of the unicast routing table. snDvmrpEnable must be 'enabled' before this table is read.
IP snDvmrpRouteUpstreamNeighbor	1.3.6.1.4.1.1991.1.2.5.1.15.1.4	IpAddress	read-only	The address of the upstream neighbor (e.g., RPF neighbor) from which IP datagrams from these sources are received.
INT snDvmrpRouteVifIndex	1.3.6.1.4.1.1991.1.2.5.1.15.1.5	INTEGER	read-only	The value of snDvmrpVInterfaceVifIndex for the virtual interface on which IP datagrams sent by these sources are received.
INT snDvmrpTriggerInterval	1.3.6.1.4.1.1991.1.2.5.1.6	INTEGER	read-write	This is the time interval at which triggered updates are sent out. Value is in number of seconds. snDvmrpEnable must be 'enabled' before this object is writen.
STR snDvmrpVersion	1.3.6.1.4.1.1991.1.2.5.1.1	DisplayString	read-only	The router's DVMRP version information.
CTR snDvmrpVIfStatDiscardGraftAckPkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.17	Counter	read-only	The number of graft acknowledge packets that have been discarded by the DVMRP virtual interface.
CTR snDvmrpVIfStatDiscardGraftPkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.14	Counter	read-only	The number of graft packets that have been discarded by the DVMRP virtual interface.
CTR snDvmrpVIfStatDiscardProbePkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.8	Counter	read-only	The number of probe packets that have been discarded by the DVMRP virtual interface.
CTR snDvmrpVIfStatDiscardPrunePkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.20	Counter	read-only	The number of prune packets that have been discarded by the DVMRP virtual interface.
CTR snDvmrpVIfStatDiscardRtUpdatePkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.11	Counter	read-only	The number of route update packets that have been discarded by the DVMRP virtual interface.
snDvmrpVIfStatEntry	1.3.6.1.4.1.1991.1.2.5.1.17.1		not-accessible	An entry (conceptual row) in the snDvmrpVIfStatTable.
CTR snDvmrpVIfStatInGraftAckPkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.15	Counter	read-only	The number of graft acknowledge packets that have arrived on the DVMRP virtual interface.
CTR snDvmrpVIfStatInGraftPkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.12	Counter	read-only	The number of graft packets that have arrived on the DVMRP virtual interface.
CTR snDvmrpVIfStatInOctets	1.3.6.1.4.1.1991.1.2.5.1.17.1.4	Counter	read-only	The number of octets that have arrived on the DVMRP virtual interface.
CTR snDvmrpVIfStatInPkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.2	Counter	read-only	The number of packets that have arrived on the DVMRP virtual interface.
CTR snDvmrpVIfStatInProbePkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.6	Counter	read-only	The number of probe packets that have arrived on the DVMRP virtual interface.
CTR snDvmrpVIfStatInPrunePkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.18	Counter	read-only	The number of prune packets that have arrived on the DVMRP virtual interface.
CTR snDvmrpVIfStatInRtUpdatePkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.9	Counter	read-only	The number of route update packets that have arrived on the DVMRP virtual interface.
CTR snDvmrpVIfStatOutGraftAckPkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.16	Counter	read-only	The number of graft acknowledge packets that have been sent on the DVMRP virtual interface.
CTR snDvmrpVIfStatOutGraftPkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.13	Counter	read-only	The number of graft packets that have been sent on the DVMRP virtual interface.
CTR snDvmrpVIfStatOutOctets	1.3.6.1.4.1.1991.1.2.5.1.17.1.5	Counter	read-only	The number of octets that have been sent on the DVMRP virtual interface.
CTR snDvmrpVIfStatOutPkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.3	Counter	read-only	The number of packets that have been sent on the DVMRP virtual interface.
CTR snDvmrpVIfStatOutProbePkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.7	Counter	read-only	The number of probe packets that have been sent on the DVMRP virtual interface.
CTR snDvmrpVIfStatOutPrunePkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.19	Counter	read-only	The number of prune packets that have been sent on the DVMRP virtual interface.
CTR snDvmrpVIfStatOutRtUpdatePkts	1.3.6.1.4.1.1991.1.2.5.1.17.1.10	Counter	read-only	The number of route update packets that have been sent on the DVMRP virtual interface.
snDvmrpVIfStatTable	1.3.6.1.4.1.1991.1.2.5.1.17		not-accessible	The (conceptual) table listing the router's DVMRP virtual interface statistical counters. snDvmrpEnable must be 'enabled' before this table is read.
INT snDvmrpVIfStatVifIndex	1.3.6.1.4.1.1991.1.2.5.1.17.1.1	INTEGER	read-only	The ifIndex value of this DVMRP virtual interface.
RTR snDvmrpVInterfaceAdvertiseLocal	1.3.6.1.4.1.1991.1.2.5.1.13.1.9	RtrStatus	read-write	Enable or disable the advertising of this local route.
RTR snDvmrpVInterfaceEncapsulation	1.3.6.1.4.1.1991.1.2.5.1.13.1.10	RtrStatus	read-write	Enable or disable the encapsulation of the DVMRP control packets when using IPINIP encapsulation.
snDvmrpVInterfaceEntry	1.3.6.1.4.1.1991.1.2.5.1.13.1		not-accessible	An entry (conceptual row) in the snDvmrpVInterfaceTable. This row augments ipMRouteInterfaceEntry in the IP Multicast MIB, where the threshold object resides.
IP snDvmrpVInterfaceLocalAddress	1.3.6.1.4.1.1991.1.2.5.1.13.1.4	IpAddress	read-write	The IP address of the local end of this DVMRP virtual interface.
INT snDvmrpVInterfaceMetric	1.3.6.1.4.1.1991.1.2.5.1.13.1.7	INTEGER	read-write	The distance metric for this DVMRP virtual interface which is used to calculate distance vectors.
INT snDvmrpVInterfaceOperState	1.3.6.1.4.1.1991.1.2.5.1.13.1.3	INTEGER	read-only	The current operational state of this DVMRP virtual interface.
IP snDvmrpVInterfaceRemoteAddress	1.3.6.1.4.1.1991.1.2.5.1.13.1.5	IpAddress	read-write	The IP address of the remote end of this DVMRP virtual interface. For a tunnel, this is the IP address of the neighboring router. For a subnet, this is the subnet address.
IP snDvmrpVInterfaceRemoteSubnetMask	1.3.6.1.4.1.1991.1.2.5.1.13.1.6	IpAddress	read-only	The subnet mask for a directly connected subnet. For a tunnel, this should be 0.0.0.0.
INT snDvmrpVInterfaceStatus	1.3.6.1.4.1.1991.1.2.5.1.13.1.11	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2)....Setting it to 'valid' has the effect of changing the row to operative.
snDvmrpVInterfaceTable	1.3.6.1.4.1.1991.1.2.5.1.13		not-accessible	The (conceptual) table listing the router's DVMRP virtual interfaces. snDvmrpEnable must be 'enabled' before this table is read or writen.
INT snDvmrpVInterfaceTtlThreshold	1.3.6.1.4.1.1991.1.2.5.1.13.1.8	INTEGER	read-write	This is the minimum time-to-live value to forward the packets out of this virtual interface.
INT snDvmrpVInterfaceType	1.3.6.1.4.1.1991.1.2.5.1.13.1.2	INTEGER	read-write	The type of this DVMRP virtual interface, whether it uses a tunnel, a physical interface for which we are a querier, or a physical interface for which we are not a querier. For write operation, this object can only accept tunnel(1) to configure a tunnel interface or subnet(3) to configure a physical interface.
INT snDvmrpVInterfaceVifIndex	1.3.6.1.4.1.1991.1.2.5.1.13.1.1	INTEGER	read-only	The ifIndex value of this DVMRP virtual interface.
snFsrpGlobal	1.3.6.1.4.1.1991.1.2.7.1
INT snFsrpGroupOperMode	1.3.6.1.4.1.1991.1.2.7.1.1	INTEGER	read-write	The FSRP is configured on this system either enabled or disabled and the default is disabled mode. disabled(0)..........disable FSRP enabled(1)...........activate FSRP
OCT snFsrpIfChassisTrackPortMask	1.3.6.1.4.1.1991.1.2.7.2.1.1.11	OCTET STRING	read-write	This object specifies the identity of the physical port whose state is to be monitored. Each bit is a port of the system. Default value is 0. If this object is configured then the Preference Level of this interface will be adjusted dynamically depending on the state of the Track Port. The interface's Preference Level is reduced by value of Preference Level parameter when the Track Port states first changes from UP to DOWN. When the Track Port next comes up the interface's Preference Level is increased by the amount specified by the Preference Level. The Chassis router FSRP Track port membership. (It was obsoleted after release 07100, replaced by snFsrpIfTrackPortList)
snFsrpIfEntry	1.3.6.1.4.1.1991.1.2.7.2.1.1		not-accessible	The FSRP Interface Entry describes one interface from the viewpoint of FSRP.
IP snFsrpIfIpAddress	1.3.6.1.4.1.1991.1.2.7.2.1.1.2	IpAddress	read-only	The IP Address of the physical router port of this interface.
INT snFsrpIfKeepAliveTime	1.3.6.1.4.1.1991.1.2.7.2.1.1.9	INTEGER	read-write	The heart-beat is from 1 to 120 seconds.
IP snFsrpIfOtherRtrIpAddr	1.3.6.1.4.1.1991.1.2.7.2.1.1.4	IpAddress	read-write	The IP Address of the Other Router on this ip subnet that operates FSRP and to whom the Keep Alive message need to be sent by this router. This object must be configured for FSRP to work correctly
INT snFsrpIfPort	1.3.6.1.4.1.1991.1.2.7.2.1.1.1	INTEGER	read-only	The physical router port of this FSRP interface.
INT snFsrpIfPreferLevel	1.3.6.1.4.1.1991.1.2.7.2.1.1.5	INTEGER	read-write	The higher the number the higher the priority is. This parameter decides which router should becomes the Active Router for the interface. A Router with higher priority selected to becomes the Active Router.
INT snFsrpIfRouterDeadTime	1.3.6.1.4.1.1991.1.2.7.2.1.1.10	INTEGER	read-write	The hold time of the Fsrp router is from 3 to 255 seconds.
INT snFsrpIfRowStatus	1.3.6.1.4.1.1991.1.2.7.2.1.1.7	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
INT snFsrpIfState	1.3.6.1.4.1.1991.1.2.7.2.1.1.8	INTEGER	read-only	This object specifies the FSRP Router's interface state as: init(0)...initialization state. negotiating(1)...negotiating state. standby(2)...standby state. active(3)...active state.
INT snFsrpIfStateChangeTrap	1.3.6.1.4.1.1991.1.2.7.1.2	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate FSRP interface state change traps.
snFsrpIfTable	1.3.6.1.4.1.1991.1.2.7.2.1		not-accessible	The FSRP Interface Table describes the interfaces from the viewpoint of FSRP.
OCT snFsrpIfTrackPortList	1.3.6.1.4.1.1991.1.2.7.2.1.1.12	OCTET STRING	read-write	This object specifies the identity of the physical port whose state is to be monitored. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number. Default value is 0 length octet string. If this object is configured then the Preference Level of this interface will be adjusted dynamically depending on the state of the Track Port. The interface's Preference Level is reduced by value of Preference Level parameter when the Track Port states first changes from UP to DOWN. When the Track Port next comes up the interface's Preference Level is increased by the amount specified by the Preference Level. The router FSRP physical track port membership.
POR snFsrpIfTrackPortMask	1.3.6.1.4.1.1991.1.2.7.2.1.1.6	PortMask	read-write	This object specifies the identity of the physical port whose state is to be monitored. Each bit is a port of the system. Default value is 0. If this object is configured then the Preference Level of this interface will be adjusted dynamically depending on the state of the Track Port. The interface's Preference Level is reduced by value of Preference Level parameter when the Track Port states first changes from UP to DOWN. When the Track Port next comes up the interface's Preference Level is increased by the amount specified by the Preference Level. The Standalone router FSRP Track port membership (Not used for Chassis Product)
IP snFsrpIfVirRtrIpAddr	1.3.6.1.4.1.1991.1.2.7.2.1.1.3	IpAddress	read-write	The IP Address of the Virtual Router for the interface. The Virtual Router IP address need to be configured on the interface before Redundant Router Function can operate on the interface. This address has to be same on all the routers that going to participate in the Redundant Router Function on a given subnet.
snFsrpIntf	1.3.6.1.4.1.1991.1.2.7.2
snGblRtGeneral	1.3.6.1.4.1.1991.1.2.8.1
RTR snGblRtRouteOnly	1.3.6.1.4.1.1991.1.2.8.1.1	RtrStatus	read-write	If this object is 'enabled', this switching router will only route packets. If this object is 'disabled', this switching router will first route packets. If route cannot perform, it will switch packets.
INT snIpAsPathAccessListAction	1.3.6.1.4.1.1991.1.2.2.12.1.3	INTEGER	read-write	Action to take if the bgp address match with this filter.
snIpAsPathAccessListEntry	1.3.6.1.4.1.1991.1.2.2.12.1		not-accessible	An entry in the Ip As-Path Access List table.
INT snIpAsPathAccessListIndex	1.3.6.1.4.1.1991.1.2.2.12.1.1	INTEGER	read-only	The table index for a filter entry.
OCT snIpAsPathAccessListRegExpression	1.3.6.1.4.1.1991.1.2.2.12.1.4	OCTET STRING	read-write	Autonomous system in the filter using a regular expression. Each character of the regular expression string is represented by one octet.
INT snIpAsPathAccessListRowStatus	1.3.6.1.4.1.1991.1.2.2.12.1.5	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
INT snIpAsPathAccessListSequence	1.3.6.1.4.1.1991.1.2.2.12.1.2	INTEGER	read-only	The table sequence index for a filter entry.
INT snIpAsPathAccessListStringAction	1.3.6.1.4.1.1991.1.2.2.16.1.3	INTEGER	read-write	Action to take if the bgp address match with this filter.
snIpAsPathAccessListStringEntry	1.3.6.1.4.1.1991.1.2.2.16.1		not-accessible	An entry in the Ip As-Path Access List table.
STR snIpAsPathAccessListStringName	1.3.6.1.4.1.1991.1.2.2.16.1.1	DisplayString	read-only	The table index for a filter entry, string version.
STR snIpAsPathAccessListStringRegExpression	1.3.6.1.4.1.1991.1.2.2.16.1.4	DisplayString	read-write	Autonomous system in the filter using a regular expression. Each character of the regular expression string is represented by one octet.
INT snIpAsPathAccessListStringRowStatus	1.3.6.1.4.1.1991.1.2.2.16.1.5	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
INT snIpAsPathAccessListStringSequence	1.3.6.1.4.1.1991.1.2.2.16.1.2	INTEGER	read-only	The table sequence index for a filter entry.
snIpAsPathAccessListStringTable	1.3.6.1.4.1.1991.1.2.2.16		not-accessible	Ip As-Path Access List table, string version.
snIpAsPathAccessListTable	1.3.6.1.4.1.1991.1.2.2.12		not-accessible	Ip As-Path Access List table.
INT snIpCommunityListAction	1.3.6.1.4.1.1991.1.2.2.13.1.3	INTEGER	read-write	Action to take if the bgp address match with this filter.
OCT snIpCommunityListCommNum	1.3.6.1.4.1.1991.1.2.2.13.1.4	OCTET STRING	read-write	A number from 1 to 0xFFFFFFFF. There are 20 of them. This integer number is represented by 4 OCTETs.
snIpCommunityListEntry	1.3.6.1.4.1.1991.1.2.2.13.1		not-accessible	An entry in the Ip Community List table.
INT snIpCommunityListIndex	1.3.6.1.4.1.1991.1.2.2.13.1.1	INTEGER	read-only	The table index for a filter entry.
INT snIpCommunityListInternet	1.3.6.1.4.1.1991.1.2.2.13.1.5	INTEGER	read-write	Disabled/Enabled the Internet Community.
INT snIpCommunityListLocalAs	1.3.6.1.4.1.1991.1.2.2.13.1.9	INTEGER	read-write	Send this route to peers in other sub-autonomous systems within the local confederation. Do not advertise this route to an external system.
INT snIpCommunityListNoAdvertise	1.3.6.1.4.1.1991.1.2.2.13.1.6	INTEGER	read-write	Do not advertise this route to any peer (internal or external).
INT snIpCommunityListNoExport	1.3.6.1.4.1.1991.1.2.2.13.1.7	INTEGER	read-write	Do not advertise this route to an EBGP peer.
INT snIpCommunityListRowStatus	1.3.6.1.4.1.1991.1.2.2.13.1.8	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
INT snIpCommunityListSequence	1.3.6.1.4.1.1991.1.2.2.13.1.2	INTEGER	read-only	The table sequence index for a filter entry.
INT snIpCommunityListStringAction	1.3.6.1.4.1.1991.1.2.2.17.1.3	INTEGER	read-write	Action to take if the bgp address match with this filter.
OCT snIpCommunityListStringCommNum	1.3.6.1.4.1.1991.1.2.2.17.1.4	OCTET STRING	read-write	A number from 1 to 0xFFFFFFFF. There are 20 of them. This integer number is represented by 4 OCTETs.
snIpCommunityListStringEntry	1.3.6.1.4.1.1991.1.2.2.17.1		not-accessible	An entry in the Ip Community ListString table.
INT snIpCommunityListStringInternet	1.3.6.1.4.1.1991.1.2.2.17.1.5	INTEGER	read-write	Disabled/Enabled the Internet Community.
INT snIpCommunityListStringLocalAs	1.3.6.1.4.1.1991.1.2.2.17.1.9	INTEGER	read-write	Send this route to peers in other sub-autonomous systems within the local confederation. Do not advertise this route to an external system.
STR snIpCommunityListStringName	1.3.6.1.4.1.1991.1.2.2.17.1.1	DisplayString	read-only	The table index for a filter entry.
INT snIpCommunityListStringNoAdvertise	1.3.6.1.4.1.1991.1.2.2.17.1.6	INTEGER	read-write	Do not advertise this route to any peer (internal or external).
INT snIpCommunityListStringNoExport	1.3.6.1.4.1.1991.1.2.2.17.1.7	INTEGER	read-write	Do not advertise this route to an EBGP peer.
INT snIpCommunityListStringRowStatus	1.3.6.1.4.1.1991.1.2.2.17.1.8	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
INT snIpCommunityListStringSequence	1.3.6.1.4.1.1991.1.2.2.17.1.2	INTEGER	read-only	The table sequence index for a filter entry.
snIpCommunityListStringTable	1.3.6.1.4.1.1991.1.2.2.17		not-accessible	Ip Community ListString table, string version.
snIpCommunityListTable	1.3.6.1.4.1.1991.1.2.2.13		not-accessible	Ip Community List table.
INT snIpPrefixListAction	1.3.6.1.4.1.1991.1.2.2.14.1.4	INTEGER	read-write	Action to take if the ip prefix match with this filter.
IP snIpPrefixListAddr	1.3.6.1.4.1.1991.1.2.2.14.1.5	IpAddress	read-write	Prefix IP address.
OCT snIpPrefixListDesc	1.3.6.1.4.1.1991.1.2.2.14.1.3	OCTET STRING	read-write	An octet string of the ip prefix list description, each character of the name is represented by one octet.
snIpPrefixListEntry	1.3.6.1.4.1.1991.1.2.2.14.1		not-accessible	An entry in the Ip As-Path Access List table.
INT snIpPrefixListGeValue	1.3.6.1.4.1.1991.1.2.2.14.1.7	INTEGER	read-write	Greater than value.
INT snIpPrefixListLeValue	1.3.6.1.4.1.1991.1.2.2.14.1.8	INTEGER	read-write	Less than value.
IP snIpPrefixListMask	1.3.6.1.4.1.1991.1.2.2.14.1.6	IpAddress	read-write	Prefix IP mask.
OCT snIpPrefixListName	1.3.6.1.4.1.1991.1.2.2.14.1.1	OCTET STRING	read-only	An octet string of the ip prefix list name, each character of the name is represented by one octet.
INT snIpPrefixListRowStatus	1.3.6.1.4.1.1991.1.2.2.14.1.9	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
INT snIpPrefixListSequence	1.3.6.1.4.1.1991.1.2.2.14.1.2	INTEGER	read-only	The table sequence index for a filter entry.
snIpPrefixListTable	1.3.6.1.4.1.1991.1.2.2.14		not-accessible	Ip Prefix List table.
snLoopbackIntfConfigEntry	1.3.6.1.4.1.1991.1.2.13.1.1		not-accessible	An entry in the Loopback Interface Config table.
INT snLoopbackIntfConfigPortIndex	1.3.6.1.4.1.1991.1.2.13.1.1.1	INTEGER	read-only	The port index for Loopback Interface config entry.
snLoopbackIntfConfigTable	1.3.6.1.4.1.1991.1.2.13.1		not-accessible	Loopback Interface Config table.
INT snLoopbackIntfMode	1.3.6.1.4.1.1991.1.2.13.1.1.2	INTEGER	read-write	The Loopback Interface mode.
INT snLoopbackIntfRowStatus	1.3.6.1.4.1.1991.1.2.13.1.1.3	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
snPimCandidateBSREntry	1.3.6.1.4.1.1991.1.2.9.2.2.1		not-accessible	An entry (conceptual row) in the snPimCandidateBSRTable.
INT snPimCandidateBSRHashMaskLen	1.3.6.1.4.1.1991.1.2.9.2.2.1.3	INTEGER	read-write	The hash mask value for this router as a candidate bootstrap router.
IP snPimCandidateBSRIPAddress	1.3.6.1.4.1.1991.1.2.9.2.2.1.2	IpAddress	read-only	The (unicast) address of the Candidate BSR.
INT snPimCandidateBSRPortID	1.3.6.1.4.1.1991.1.2.9.2.2.1.1	INTEGER	read-write	The IP address of the PIM interface. The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number.
INT snPimCandidateBSRPreference	1.3.6.1.4.1.1991.1.2.9.2.2.1.4	INTEGER	read-write	The preference value for this router as a candidate bootstrap router.
snPimCandidateBSRTable	1.3.6.1.4.1.1991.1.2.9.2.2		not-accessible	Candidate Bootstrap Router information.
snPimCandidateRPEntry	1.3.6.1.4.1.1991.1.2.9.2.4.1		not-accessible	An entry (conceptual row) in the snPimCandidateRPTable.
IP snPimCandidateRPGroupAddress	1.3.6.1.4.1.1991.1.2.9.2.4.1.1	IpAddress	read-only	The IP multicast group address which, when combined with snPimCandidateRPGroupMask, identifies a group prefix for which the local router will advertise itself as a Candidate-RP.
IP snPimCandidateRPIPAddress	1.3.6.1.4.1.1991.1.2.9.2.4.1.3	IpAddress	read-write	The (unicast) address of the interface which will be advertised as a Candidate-RP.
IP snPimCandidateRPMask	1.3.6.1.4.1.1991.1.2.9.2.4.1.2	IpAddress	read-only	The multicast group address mask which, when combined with snPimCandidateRPGroupMask, identifies a group prefix for which the local router will advertise itself as a Candidate-RP.
INT snPimCandidateRPRowStatus	1.3.6.1.4.1.1991.1.2.9.2.4.1.4	INTEGER	read-write	The status of this row, by which new entries may be created, or old entries deleted from this table. This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row other(1)....some other case valid(2)....the row exists and is valid
snPimCandidateRPTable	1.3.6.1.4.1.1991.1.2.9.2.4		not-accessible	The (conceptual) table listing the IP multicast groups for which the local router is to advertise itself as a Candidate-RP. If this table is empty, then the local router will advertise itself as a Candidate-RP for all groups snPimEnable must be 'enabled' before this table is read or writen.
RTR snPimEnable	1.3.6.1.4.1.1991.1.2.9.1.1	RtrStatus	read-write	Enable or disable PIM on this router.
INT snPimGraftRetransmitTime	1.3.6.1.4.1.1991.1.2.9.1.5	INTEGER	read-write	This is the time interval after which a graft message will be retransmitted if graft acknowledge message has not been received. Value is in number of seconds. snPimEnable must be 'enabled' before this object is writen.
INT snPimHelloTime	1.3.6.1.4.1.1991.1.2.9.1.3	INTEGER	read-write	This is the interval at which hello message is sent out an interface to the neighbouring router. This is used to detect the presence or abscense of a neighbouring router. Value is in number of seconds. snPimEnable must be 'enabled' before this object is writen.
INT snPimInactivityTime	1.3.6.1.4.1.1991.1.2.9.1.6	INTEGER	read-write	This is the interval after which the forwarding entry is deleted. When a packet is received for a group entry, this time is reset. This is used to only keep the forwarding entries for the active sessions. Value is in number of seconds. snPimEnable must be 'enabled' before this object is writen.
INT snPimJoinPruneInterval	1.3.6.1.4.1.1991.1.2.9.2.1	INTEGER	read-write	The default interval in seconds at which periodic PIM-SM Join/Prune messages are to be sent. snPimEnable must be 'enabled' before this table is read or writen.
snPimMIBObjects	1.3.6.1.4.1.1991.1.2.9.1
IP snPimNeighborAddress	1.3.6.1.4.1.1991.1.2.9.1.8.1.3	IpAddress	read-only	The IP address of the PIM neighbor for which this entry contains information.
snPimNeighborEntry	1.3.6.1.4.1.1991.1.2.9.1.8.1		not-accessible	An entry (conceptual row) in the snPimNeighborTable.
INT snPimNeighborEntryIndex	1.3.6.1.4.1.1991.1.2.9.1.8.1.1	INTEGER	read-only	The table entry index.
TIK snPimNeighborExpiryTime	1.3.6.1.4.1.1991.1.2.9.1.8.1.5	TimeTicks	read-only	The minimum time remaining before this PIM neighbor will be aged out.
INT snPimNeighborRouterTimeout	1.3.6.1.4.1.1991.1.2.9.1.2	INTEGER	read-write	This is the time interval after which the neighbour router is considered down. Value is in number of seconds. snPimEnable must be 'enabled' before this object is writen.
snPimNeighborTable	1.3.6.1.4.1.1991.1.2.9.1.8		not-accessible	The (conceptual) table listing the router's PIM neighbors. snPimEnable must be 'enabled' before this table is read.
TIK snPimNeighborUpTime	1.3.6.1.4.1.1991.1.2.9.1.8.1.4	TimeTicks	read-only	The time since this PIM neighbor (last) became a neighbor of the local router.
INT snPimNeighborVifIndex	1.3.6.1.4.1.1991.1.2.9.1.8.1.2	INTEGER	read-only	The value of VifIndex for the virtual interface used to reach this PIM neighbor.
INT snPimPruneTime	1.3.6.1.4.1.1991.1.2.9.1.4	INTEGER	read-write	This is the duration of time for which the prune state is stored. Value is in number of seconds. snPimEnable must be 'enabled' before this object is writen.
snPimRPSetEntry	1.3.6.1.4.1.1991.1.2.9.2.3.1		not-accessible	An entry (conceptual row) in the snPimRPSetTable.
IP snPimRPSetGroupAddress	1.3.6.1.4.1.1991.1.2.9.2.3.1.1	IpAddress	read-only	The IP multicast group address which, when combined with snPimRPSetGroupMask, gives the group prefix for which this entry contains information about the Candidate-RP.
INT snPimRPSetHoldTime	1.3.6.1.4.1.1991.1.2.9.2.3.1.4	INTEGER	read-only	The holdtime, in seconds, of a Candidate-RP. If the local router is not the BSR, this value is 0.
IP snPimRPSetIPAddress	1.3.6.1.4.1.1991.1.2.9.2.3.1.3	IpAddress	read-only	The IP address of the Candidate-RP.
IP snPimRPSetMask	1.3.6.1.4.1.1991.1.2.9.2.3.1.2	IpAddress	read-only	The multicast group address mask which, when combined with snPimRPSetGroupAddress, gives the group prefix for which this entry contains information about the Candidate-RP.
snPimRPSetTable	1.3.6.1.4.1.1991.1.2.9.2.3		not-accessible	The (conceptual) table listing PIM information for candidate Rendezvous Points (RPs) for IP multicast groups. When the local router is the BSR, this information is obtained from received Candidate-RP-Advertisements. When the local router is not the BSR, this information is obtained from received RP-Set messages. snPimEnable must be 'enabled' before this table is read or writen.
snPimSMMIBObjects	1.3.6.1.4.1.1991.1.2.9.2
CTR snPimVIfStatDiscardAssertPkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.10	Counter	read-only	The number of assert packets that have been discarded by the PIM virtual interface.
CTR snPimVIfStatDiscardGraftAckPkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.19	Counter	read-only	The number of graft acknowledge packets that have been discarded by the PIM virtual interface.
CTR snPimVIfStatDiscardGraftPkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.16	Counter	read-only	The number of graft packets that have been discarded by the PIM virtual interface.
CTR snPimVIfStatDiscardHelloPkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.13	Counter	read-only	The number of hello packets that have been discarded by the PIM virtual interface.
CTR snPimVIfStatDiscardJoinPkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.4	Counter	read-only	The number of join packets that have been discarded by the PIM virtual interface.
CTR snPimVIfStatDiscardPrunePkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.7	Counter	read-only	The number of prune packets that have been discarded by the PIM virtual interface.
snPimVIfStatEntry	1.3.6.1.4.1.1991.1.2.9.1.9.1		not-accessible	An entry (conceptual row) in the snPimVIfStatTable.
CTR snPimVIfStatInAssertPkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.8	Counter	read-only	The number of assert packets that have arrived on the PIM virtual interface.
CTR snPimVIfStatInGraftAckPkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.17	Counter	read-only	The number of graft acknowledge packets that have arrived on the PIM virtual interface.
CTR snPimVIfStatInGraftPkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.14	Counter	read-only	The number of graft packets that have arrived on the PIM virtual interface.
CTR snPimVIfStatInHelloPkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.11	Counter	read-only	The number of hello packets that have arrived on the PIM virtual interface.
CTR snPimVIfStatInJoinPkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.2	Counter	read-only	The number of join packets that have arrived on the PIM virtual interface.
CTR snPimVIfStatInPrunePkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.5	Counter	read-only	The number of prune packets that have arrived on the PIM virtual interface.
CTR snPimVIfStatOutAssertPkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.9	Counter	read-only	The number of assert packets that have been sent on the PIM virtual interface.
CTR snPimVIfStatOutGraftAckPkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.18	Counter	read-only	The number of graft acknowledge packets that have been sent on the PIM virtual interface.
CTR snPimVIfStatOutGraftPkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.15	Counter	read-only	The number of graft packets that have been sent on the PIM virtual interface.
CTR snPimVIfStatOutHelloPkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.12	Counter	read-only	The number of hello packets that have been sent on the PIM virtual interface.
CTR snPimVIfStatOutJoinPkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.3	Counter	read-only	The number of join packets that have been sent on the PIM virtual interface.
CTR snPimVIfStatOutPrunePkts	1.3.6.1.4.1.1991.1.2.9.1.9.1.6	Counter	read-only	The number of prune packets that have been sent on the PIM virtual interface.
snPimVIfStatTable	1.3.6.1.4.1.1991.1.2.9.1.9		not-accessible	The (conceptual) table listing the router's PIM virtual interface statistical counters. snPimEnable must be 'enabled' before this table is read.
INT snPimVIfStatVifIndex	1.3.6.1.4.1.1991.1.2.9.1.9.1.1	INTEGER	read-only	The ifIndex value of this PIM virtual interface.
IP snPimVInterfaceDR	1.3.6.1.4.1.1991.1.2.9.1.7.1.6	IpAddress	read-only	The Designated Router on this PIM virtual interface. For point-to-point interfaces, this object has the value 0.0.0.0.
snPimVInterfaceEntry	1.3.6.1.4.1.1991.1.2.9.1.7.1		not-accessible	An entry (conceptual row) in the snPimVInterfaceTable.
IP snPimVInterfaceLocalAddress	1.3.6.1.4.1.1991.1.2.9.1.7.1.3	IpAddress	read-write	The IP address of the local end of this PIM virtual interface.
IP snPimVInterfaceLocalSubnetMask	1.3.6.1.4.1.1991.1.2.9.1.7.1.4	IpAddress	read-only	The network mask for the IP address of the PIM virtual interface. For a tunnel, this should be 0.0.0.0.
INT snPimVInterfaceMode	1.3.6.1.4.1.1991.1.2.9.1.7.1.9	INTEGER	read-write	The configured mode of this PIM interface.
IP snPimVInterfaceRemoteAddress	1.3.6.1.4.1.1991.1.2.9.1.7.1.5	IpAddress	read-write	The IP address of the remote end of this PIM virtual interface.
INT snPimVInterfaceStatus	1.3.6.1.4.1.1991.1.2.9.1.7.1.8	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2)....Setting it to 'valid' has the effect of changing the row to operative.
snPimVInterfaceTable	1.3.6.1.4.1.1991.1.2.9.1.7		not-accessible	The (conceptual) table listing the router's PIM virtual interfaces. snPimEnable must be 'enabled' before this table is read or writen.
INT snPimVInterfaceTtlThreshold	1.3.6.1.4.1.1991.1.2.9.1.7.1.7	INTEGER	read-write	This is the minimum time-to-live value to forward the packets out of this interface.
INT snPimVInterfaceType	1.3.6.1.4.1.1991.1.2.9.1.7.1.2	INTEGER	read-write	The type of PIM virtual interface, whether it uses a tunnel or a physical interface.
INT snPimVInterfaceVifIndex	1.3.6.1.4.1.1991.1.2.9.1.7.1.1	INTEGER	read-only	The ifIndex value of this PIM virtual interface.
INT snRtArpAge	1.3.6.1.4.1.1991.1.2.2.1.6	INTEGER	read-write	The time in minutes an ARP entry can be valid without relearning. 0 - Don't not age.
snRtBcastFwd	1.3.6.1.4.1.1991.1.2.2.9
snRtBcastFwdGeneral	1.3.6.1.4.1.1991.1.2.2.9.1
INT snRtBootpRelayMax	1.3.6.1.4.1.1991.1.2.2.1.5	INTEGER	read-write	Maximum number of hop the bootp packet should travel.
IP snRtBootpServer	1.3.6.1.4.1.1991.1.2.2.1.4	IpAddress	read-write	IP address of bootp server to which bootp packet need to be relayed.
CLE snRtClearArpCache	1.3.6.1.4.1.1991.1.2.2.1.1	ClearStatus	read-write	clear(1) will clear arp cache table.
CLE snRtClearIpCache	1.3.6.1.4.1.1991.1.2.2.1.2	ClearStatus	read-write	clear(1) will clear ip route cache table.
CLE snRtClearIpRoute	1.3.6.1.4.1.1991.1.2.2.1.3	ClearStatus	read-write	clear(1) will clear ip route table.
RTR snRtIpDirBcastFwd	1.3.6.1.4.1.1991.1.2.2.1.16	RtrStatus	read-write	Enable/Disable directed broadcast forwarding.
INT snRtIpFilterAction	1.3.6.1.4.1.1991.1.2.2.3.1.2	INTEGER	read-write	Action to take if the ip packet match with this filter.
IP snRtIpFilterDestIp	1.3.6.1.4.1.1991.1.2.2.3.1.6	IpAddress	read-write	Destination IP address.
IP snRtIpFilterDestMask	1.3.6.1.4.1.1991.1.2.2.3.1.7	IpAddress	read-write	Destination IP subnet mask.
snRtIpFilterEntry	1.3.6.1.4.1.1991.1.2.2.3.1		not-accessible	An entry in the IP filter table.
RTR snRtIpFilterEstablished	1.3.6.1.4.1.1991.1.2.2.3.1.11	RtrStatus	read-write	Enable/Disable the filtering of established TCP packets of which the ACK or RESET flag is on. This additional filter only applies to TCP transport protocol.
INT snRtIpFilterIndex	1.3.6.1.4.1.1991.1.2.2.3.1.1	INTEGER	read-only	The table index for a filter entry.
INT snRtIpFilterOperand	1.3.6.1.4.1.1991.1.2.2.3.1.9	INTEGER	read-write	For now this only refers to transport protocol port number. 0 means NA
INT snRtIpFilterOperator	1.3.6.1.4.1.1991.1.2.2.3.1.8	INTEGER	read-write	Type of comparison to perform. for now, this only applys to tcp or udp to compare the port number
INT snRtIpFilterProtocol	1.3.6.1.4.1.1991.1.2.2.3.1.3	INTEGER	read-write	Transport protocol. 0 means don't care
INT snRtIpFilterQosPriority	1.3.6.1.4.1.1991.1.2.2.3.1.12	INTEGER	read-write	The router L4 Qos Priority values are: low(0) -- low prority high(1) -- high prority. The Priority values are: level0(0), level1(1), level2(2), level3(3), level4(4), level5(5), level6(6), level7(7)
ROW snRtIpFilterRowStatus	1.3.6.1.4.1.1991.1.2.2.3.1.10	RowSts	read-write	To create or delete a filter entry.
IP snRtIpFilterSourceIp	1.3.6.1.4.1.1991.1.2.2.3.1.4	IpAddress	read-write	Source IP address.
IP snRtIpFilterSourceMask	1.3.6.1.4.1.1991.1.2.2.3.1.5	IpAddress	read-write	Source IP subnet mask.
snRtIpFilterTable	1.3.6.1.4.1.1991.1.2.2.3		not-accessible	IP filter table.
INT snRtIpFwdCacheAction	1.3.6.1.4.1.1991.1.2.2.11.1.7	INTEGER	read-only	The action to take.
INT snRtIpFwdCacheCurEntries	1.3.6.1.4.1.1991.1.2.2.1.14	INTEGER	read-only	The current number of ip forwarding table entries.
snRtIpFwdCacheEntry	1.3.6.1.4.1.1991.1.2.2.11.1		not-accessible	An entry in the IP forwarding cache table.
INT snRtIpFwdCacheFragCheck	1.3.6.1.4.1.1991.1.2.2.11.1.8	INTEGER	read-only	Check for fragmentation.
INT snRtIpFwdCacheIndex	1.3.6.1.4.1.1991.1.2.2.11.1.1	INTEGER	read-only	The table index for a ip forwarding cache table entry.
IP snRtIpFwdCacheIp	1.3.6.1.4.1.1991.1.2.2.11.1.2	IpAddress	read-only	The IP address of a station.
OCT snRtIpFwdCacheMac	1.3.6.1.4.1.1991.1.2.2.11.1.3	OCTET STRING	read-only	The Mac address of an IP station.
INT snRtIpFwdCacheMaxEntries	1.3.6.1.4.1.1991.1.2.2.1.13	INTEGER	read-only	The maximum number of ip forwarding table entries.
IP snRtIpFwdCacheNextHopIp	1.3.6.1.4.1.1991.1.2.2.11.1.4	IpAddress	read-only	The next hop router IP address.
INT snRtIpFwdCacheOutgoingPort	1.3.6.1.4.1.1991.1.2.2.11.1.5	INTEGER	read-only	The outgoing port of which packets will forward to. Return port value of zero to indicate no outgoing port associated to this entry. Non-zero value has the following meanings: The bit 0 to bit 7: port number. The bit 8 to bit 11: slot number. For virtual router interface, slot number is 15, port number is the virtual router port from 1 to 60.
INT snRtIpFwdCacheSnapHdr	1.3.6.1.4.1.1991.1.2.2.11.1.9	INTEGER	read-only	Apply SNAP encapsulation.
snRtIpFwdCacheTable	1.3.6.1.4.1.1991.1.2.2.11		not-accessible	IP forwarding cache table.
INT snRtIpFwdCacheType	1.3.6.1.4.1.1991.1.2.2.11.1.6	INTEGER	read-only	The 'dynamic' or 'permanent' type for a ip forwarding cache table entry.
INT snRtIpFwdCacheVLanId	1.3.6.1.4.1.1991.1.2.2.11.1.10	INTEGER	read-only	The VLAN ID for a ip forwarding cache table entry. Return VLAN ID value of zero to indicate no VLAN associated to this entry.
snRtIpGeneral	1.3.6.1.4.1.1991.1.2.2.1
RTR snRtIpIrdpEnable	1.3.6.1.4.1.1991.1.2.2.1.7	RtrStatus	read-write	Perform router advertisement on this box.
RTR snRtIpLoadShare	1.3.6.1.4.1.1991.1.2.2.1.8	RtrStatus	read-write	If more than one route available, use them to share load.
INT snRtIpLoadShareMaxPaths	1.3.6.1.4.1.1991.1.2.2.1.18	INTEGER	read-only	Maximum number of routes can be configured to share load.
INT snRtIpLoadShareMinPaths	1.3.6.1.4.1.1991.1.2.2.1.19	INTEGER	read-only	Minimum number of routes can be configured to share load.
INT snRtIpLoadShareNumOfPaths	1.3.6.1.4.1.1991.1.2.2.1.17	INTEGER	read-write	Number of routes are used to share load.
INT snRtIpMaxStaticRouteEntries	1.3.6.1.4.1.1991.1.2.2.1.15	INTEGER	read-only	The maximum number of static route entries in the static route table.
INT snRtIpPortAccessDirection	1.3.6.1.4.1.1991.1.2.2.7.1.2	INTEGER	read-only	The incoming or outgoing check for port access.
snRtIpPortAccessEntry	1.3.6.1.4.1.1991.1.2.2.7.1		not-accessible	An entry in the IP Port access table.
OCT snRtIpPortAccessFilters	1.3.6.1.4.1.1991.1.2.2.7.1.3	OCTET STRING	read-write	1st octet correspond to 1st filter number and so on.
POR snRtIpPortAccessPortIndex	1.3.6.1.4.1.1991.1.2.2.7.1.1	PortIndex	read-only	The port index for port access entry.
ROW snRtIpPortAccessRowStatus	1.3.6.1.4.1.1991.1.2.2.7.1.4	RowSts	read-write	To create or delete a port access entry.
snRtIpPortAccessTable	1.3.6.1.4.1.1991.1.2.2.7		not-accessible	IP port access table.
snRtIpPortAddrEntry	1.3.6.1.4.1.1991.1.2.2.6.1		not-accessible	An entry in the IP Port Address table.
IP snRtIpPortAddress	1.3.6.1.4.1.1991.1.2.2.6.1.2	IpAddress	read-only	The port IP address.
POR snRtIpPortAddrPortIndex	1.3.6.1.4.1.1991.1.2.2.6.1.1	PortIndex	read-only	The port index for port address entry.
snRtIpPortAddrTable	1.3.6.1.4.1.1991.1.2.2.6		not-accessible	IP port address table.
INT snRtIpPortAddrType	1.3.6.1.4.1.1991.1.2.2.6.1.4	INTEGER	read-write	The port IP address type.
snRtIpPortConfigEntry	1.3.6.1.4.1.1991.1.2.2.8.1		not-accessible	An entry in the IP Port Config table.
POR snRtIpPortConfigPortIndex	1.3.6.1.4.1.1991.1.2.2.8.1.1	PortIndex	read-only	The port index for port config entry.
snRtIpPortConfigTable	1.3.6.1.4.1.1991.1.2.2.8		not-accessible	IP port Config table.
RTR snRtIpPortDirBcastFwd	1.3.6.1.4.1.1991.1.2.2.8.1.5	RtrStatus	read-write	Enable/Disable directed broadcast forwarding on the port.
INT snRtIpPortEncap	1.3.6.1.4.1.1991.1.2.2.8.1.3	INTEGER	read-write	Data link encapsulation to be used on the IP frame transmitted on the port.
INT snRtIpPortIfAccessDirection	1.3.6.1.4.1.1991.1.2.2.19.1.2	INTEGER	read-only	The incoming or outgoing check for port access.
snRtIpPortIfAccessEntry	1.3.6.1.4.1.1991.1.2.2.19.1		not-accessible	An entry in the IP Port access table.
OCT snRtIpPortIfAccessFilters	1.3.6.1.4.1.1991.1.2.2.19.1.3	OCTET STRING	read-write	1st octet correspond to 1st filter number and so on.
NUM snRtIpPortIfAccessInterfaceIndex	1.3.6.1.4.1.1991.1.2.2.19.1.1	InterfaceIndex	read-only	The InterfaceIndex for port access entry.
ROW snRtIpPortIfAccessRowStatus	1.3.6.1.4.1.1991.1.2.2.19.1.4	RowSts	read-write	To create or delete a port access entry.
snRtIpPortIfAccessTable	1.3.6.1.4.1.1991.1.2.2.19		not-accessible	IP port If access table.
snRtIpPortIfAddrEntry	1.3.6.1.4.1.1991.1.2.2.18.1		not-accessible	An entry in the IP Port Address table.
IP snRtIpPortIfAddress	1.3.6.1.4.1.1991.1.2.2.18.1.2	IpAddress	read-only	The port IP address.
NUM snRtIpPortIfAddrInterfaceIndex	1.3.6.1.4.1.1991.1.2.2.18.1.1	InterfaceIndex	read-only	The InterfaceIndex for port address entry.
snRtIpPortIfAddrTable	1.3.6.1.4.1.1991.1.2.2.18		not-accessible	IP port If address table.
INT snRtIpPortIfAddrType	1.3.6.1.4.1.1991.1.2.2.18.1.4	INTEGER	read-write	The port IP address type.
snRtIpPortIfConfigEntry	1.3.6.1.4.1.1991.1.2.2.20.1		not-accessible	An entry in the IP Port Config table.
NUM snRtIpPortIfConfigInterfaceIndex	1.3.6.1.4.1.1991.1.2.2.20.1.1	InterfaceIndex	read-only	The If index for port config entry.
snRtIpPortIfConfigTable	1.3.6.1.4.1.1991.1.2.2.20		not-accessible	IP port If Config table.
RTR snRtIpPortIfDirBcastFwd	1.3.6.1.4.1.1991.1.2.2.20.1.5	RtrStatus	read-write	Enable/Disable directed broadcast forwarding on the port.
INT snRtIpPortIfEncap	1.3.6.1.4.1.1991.1.2.2.20.1.3	INTEGER	read-write	Data link encapsulation to be used on the IP frame transmitted on the port.
INT snRtIpPortIfMetric	1.3.6.1.4.1.1991.1.2.2.20.1.4	INTEGER	read-write	The metric.
INT snRtIpPortIfMtu	1.3.6.1.4.1.1991.1.2.2.20.1.2	INTEGER	read-write	The maximun transfer unit. Ethernet MTU Range: 46 to 1500 POS MTU Range: 60 to 4470 ATM MTU Range: 1500 to 9180 ATM SubIf MTU Range: 1500 to 9180 For jumbo support, MTU range could be higher.
ROW snRtIpPortIfRowStatus	1.3.6.1.4.1.1991.1.2.2.18.1.5	RowSts	read-write	To create or delete a port address entry.
IP snRtIpPortIfSubnetMask	1.3.6.1.4.1.1991.1.2.2.18.1.3	IpAddress	read-write	The port IP address subnet mask.
INT snRtIpPortMetric	1.3.6.1.4.1.1991.1.2.2.8.1.4	INTEGER	read-write	The metric.
INT snRtIpPortMtu	1.3.6.1.4.1.1991.1.2.2.8.1.2	INTEGER	read-write	The maximun transfer unit.
ROW snRtIpPortRowStatus	1.3.6.1.4.1.1991.1.2.2.6.1.5	RowSts	read-write	To create or delete a port address entry.
IP snRtIpPortSubnetMask	1.3.6.1.4.1.1991.1.2.2.6.1.3	IpAddress	read-write	The port IP address subnet mask.
IP snRtIpProtocolRouterId	1.3.6.1.4.1.1991.1.2.2.1.20	IpAddress	read-write	Router Id for all IP Protocols.
RTR snRtIpProxyArp	1.3.6.1.4.1.1991.1.2.2.1.9	RtrStatus	read-write	Enable/disable proxy arp function in the box.
RTR snRtIpRarp	1.3.6.1.4.1.1991.1.2.2.1.10	RtrStatus	read-write	Enable/disable RARP server.
snRtIpRarpEntry	1.3.6.1.4.1.1991.1.2.2.4.1		not-accessible	An entry in the IP Rarp table.
INT snRtIpRarpIndex	1.3.6.1.4.1.1991.1.2.2.4.1.1	INTEGER	read-only	The table index for a Rarp entry.
IP snRtIpRarpIp	1.3.6.1.4.1.1991.1.2.2.4.1.3	IpAddress	read-write	The IP address for a Rarp entry.
OCT snRtIpRarpMac	1.3.6.1.4.1.1991.1.2.2.4.1.2	OCTET STRING	read-write	The Mac address for a Rarp entry.
ROW snRtIpRarpRowStatus	1.3.6.1.4.1.1991.1.2.2.4.1.4	RowSts	read-write	To create or delete a Rarp entry.
snRtIpRarpTable	1.3.6.1.4.1.1991.1.2.2.4		not-accessible	IP RARP table.
INT snRtIpRipDistance	1.3.6.1.4.1.1991.1.2.3.1.8	INTEGER	read-write	Administration distance.
RTR snRtIpRipEnable	1.3.6.1.4.1.1991.1.2.3.1.1	RtrStatus	read-write	Enable/disable ip rip routing.
INT snRtIpRipFiltOnAllPort	1.3.6.1.4.1.1991.1.2.3.1.7	INTEGER	read-write	Apply the ip rip global filter list snRtIpRipGblFiltList to all interfaces. This object is used to add all rip filter lists and delete all rip filter lists to/from all interfaces. Prior to sending this command, snRtIpRipGblFiltList must have been set to a proper filter list. The values that can be written are: deleteAllInBound(2)...delete all in-bound filter lists from all ports. deleteAllOutBound(3)..delete all out-bound filter lists from all ports. addAllInBound(4)......add all in-bound filter lists to all ports. addAllOutBound(5).....add all out-bound filter lists to all ports. If set operation failed, then a SET with value of (2) or (3) returns error code 'GenError'. If succeed, entries in the filter list are deleted immediately. The following values can be returned on reads: valid(1)....set operation is done and is valid.
OCT snRtIpRipGblFiltList	1.3.6.1.4.1.1991.1.2.3.1.6	OCTET STRING	read-write	An ip rip global filter list, of which each octet contains a filter ID number that forms a group of filters. A valid entry in the snRtIpRipRouteFilterTable with the corresponding filter ID number (i.e. snRtIpRipRouteFilterId) must have been created before a filter list is initialized. NULL string will be returned if there are no entries of this kind.
snRtIpRipGeneral	1.3.6.1.4.1.1991.1.2.3.1
ACT snRtIpRipNbrFilterAction	1.3.6.1.4.1.1991.1.2.3.5.1.2	Action	read-write	Action to take if the ip rip packet source IP address compares equal to the source IP address in this filter.
snRtIpRipNbrFilterEntry	1.3.6.1.4.1.1991.1.2.3.5.1		not-accessible	An entry of the ip rip neighbor filter table.
INT snRtIpRipNbrFilterId	1.3.6.1.4.1.1991.1.2.3.5.1.1	INTEGER	read-only	The filter ID to identify a filter entry.
INT snRtIpRipNbrFilterRowStatus	1.3.6.1.4.1.1991.1.2.3.5.1.4	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2).....the row exists and is valid
IP snRtIpRipNbrFilterSourceIp	1.3.6.1.4.1.1991.1.2.3.5.1.3	IpAddress	read-write	Source IP address to compare with the source IP address in a ip rip packet. IP address 0.0.0.0 always compares equal to any source IP addresses in any ip rip packets.
snRtIpRipNbrFilterTable	1.3.6.1.4.1.1991.1.2.3.5		not-accessible	ip rip neighbor filter table.
INT snRtIpRipPortAccessDir	1.3.6.1.4.1.1991.1.2.3.6.1.2	INTEGER	read-only	The access direction of incoming packet filter or outgoing packet filter.
snRtIpRipPortAccessEntry	1.3.6.1.4.1.1991.1.2.3.6.1		not-accessible	An entry of the ip interface rip access table.
OCT snRtIpRipPortAccessFilterList	1.3.6.1.4.1.1991.1.2.3.6.1.3	OCTET STRING	read-write	An ip rip filter list, of which each octet contains a filter ID number that forms a group of filters. A valid entry in the snRtIpRipRouteFilterTable with the corresponding filter ID number (i.e. snRtIpRipRouteFilterId) must have been created before a filter list is initialized.
POR snRtIpRipPortAccessPort	1.3.6.1.4.1.1991.1.2.3.6.1.1	PortIndex	read-only	The ip interface to which the rip filter applies.
INT snRtIpRipPortAccessRowStatus	1.3.6.1.4.1.1991.1.2.3.6.1.4	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2).....the row exists and is valid
snRtIpRipPortAccessTable	1.3.6.1.4.1.1991.1.2.3.6		not-accessible	ip interface rip access table.
snRtIpRipPortConfigEntry	1.3.6.1.4.1.1991.1.2.3.2.1		not-accessible	An entry in the IP Rip Port Config table.
POR snRtIpRipPortConfigPortIndex	1.3.6.1.4.1.1991.1.2.3.2.1.1	PortIndex	read-only	The port index for ip rip port config entry.
snRtIpRipPortConfigTable	1.3.6.1.4.1.1991.1.2.3.2		not-accessible	IP Rip port Config table.
INT snRtIpRipPortIfAccessDir	1.3.6.1.4.1.1991.1.2.3.8.1.2	INTEGER	read-only	The access direction of incoming packet filter or outgoing packet filter.
snRtIpRipPortIfAccessEntry	1.3.6.1.4.1.1991.1.2.3.8.1		not-accessible	An entry of the ip interface rip access table.
OCT snRtIpRipPortIfAccessFilterList	1.3.6.1.4.1.1991.1.2.3.8.1.3	OCTET STRING	read-write	An ip rip filter list, of which each octet contains a filter ID number that forms a group of filters. A valid entry in the snRtIpRipRouteFilterTable with the corresponding filter ID number (i.e. snRtIpRipRouteFilterId) must have been created before a filter list is initialized.
NUM snRtIpRipPortIfAccessPort	1.3.6.1.4.1.1991.1.2.3.8.1.1	InterfaceIndex	read-only	The ip interface to which the rip filter applies.
INT snRtIpRipPortIfAccessRowStatus	1.3.6.1.4.1.1991.1.2.3.8.1.4	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2).....the row exists and is valid
snRtIpRipPortIfAccessTable	1.3.6.1.4.1.1991.1.2.3.8		not-accessible	ip interface rip access table.
snRtIpRipPortIfConfigEntry	1.3.6.1.4.1.1991.1.2.3.7.1		not-accessible	An entry in the IP Rip Port If Config table.
NUM snRtIpRipPortIfConfigInterfaceIndex	1.3.6.1.4.1.1991.1.2.3.7.1.1	InterfaceIndex	read-only	The If index for ip rip port config entry.
snRtIpRipPortIfConfigTable	1.3.6.1.4.1.1991.1.2.3.7		not-accessible	IP Rip port If Config table.
INT snRtIpRipPortIfLearnDefault	1.3.6.1.4.1.1991.1.2.3.7.1.4	INTEGER	read-write	Apply the RIP router protocol learn-default option to the interface. The values that can be written are: disabled(0)...deleted the learn default option. enabled(1)....enabled the learn default option.
RTR snRtIpRipPortIfPoisonReverse	1.3.6.1.4.1.1991.1.2.3.7.1.3	RtrStatus	read-write	Enable/disable poison reverse.
INT snRtIpRipPortIfVersion	1.3.6.1.4.1.1991.1.2.3.7.1.2	INTEGER	read-write	The ip rip version on this port.
INT snRtIpRipPortLearnDefault	1.3.6.1.4.1.1991.1.2.3.2.1.4	INTEGER	read-write	Apply the RIP router protocol learn-default option to the interface. The values that can be written are: disabled(0)...deleted the learn default option. enabled(1)....enabled the learn default option.
RTR snRtIpRipPortPoisonReverse	1.3.6.1.4.1.1991.1.2.3.2.1.3	RtrStatus	read-write	Enable/disable poison reverse.
INT snRtIpRipPortVersion	1.3.6.1.4.1.1991.1.2.3.2.1.2	INTEGER	read-write	The ip rip version on this port.
ACT snRtIpRipRedisAction	1.3.6.1.4.1.1991.1.2.3.3.1.2	Action	read-write	The action to take when match this IP Rip Redistribution entry.
INT snRtIpRipRedisDefMetric	1.3.6.1.4.1.1991.1.2.3.1.4	INTEGER	read-write	Default metric to be used when redistribute route to rip.
RTR snRtIpRipRedisEnable	1.3.6.1.4.1.1991.1.2.3.1.3	RtrStatus	read-write	Enable/disable redistribution to rip.
snRtIpRipRedisEntry	1.3.6.1.4.1.1991.1.2.3.3.1		not-accessible	An entry in the IP Rip Redistribution table.
INT snRtIpRipRedisIndex	1.3.6.1.4.1.1991.1.2.3.3.1.1	INTEGER	read-only	The table index for a IP Rip Redistribution entry.
IP snRtIpRipRedisIp	1.3.6.1.4.1.1991.1.2.3.3.1.4	IpAddress	read-write	The ip address of the ip route to be distributed. 0.0.0.0 - all routes
IP snRtIpRipRedisMask	1.3.6.1.4.1.1991.1.2.3.3.1.5	IpAddress	read-write	The ip subnet mask of the ip route to be distributed.
MET snRtIpRipRedisMatchMetric	1.3.6.1.4.1.1991.1.2.3.3.1.6	Metric	read-write	The metric of the route to be matched to determine the redistribution. 0 - any metric value
INT snRtIpRipRedisProtocol	1.3.6.1.4.1.1991.1.2.3.3.1.3	INTEGER	read-write	The protocol to be distributed. other(1) cannot be used for SNMP-SET.
ROW snRtIpRipRedisRowStatus	1.3.6.1.4.1.1991.1.2.3.3.1.8	RowSts	read-write	To create or delete a Redistribution entry.
INT snRtIpRipRedisSetMetric	1.3.6.1.4.1.1991.1.2.3.3.1.7	INTEGER	read-write	The new metric of the route to be advertised. 0 - use the default metric.
snRtIpRipRedisTable	1.3.6.1.4.1.1991.1.2.3.3		not-accessible	IP Rip Redistribution table.
ACT snRtIpRipRouteFilterAction	1.3.6.1.4.1.1991.1.2.3.4.1.2	Action	read-write	Action to take if the ip rip packet matched with this filter.
snRtIpRipRouteFilterEntry	1.3.6.1.4.1.1991.1.2.3.4.1		not-accessible	An entry of the ip rip route filter table.
INT snRtIpRipRouteFilterId	1.3.6.1.4.1.1991.1.2.3.4.1.1	INTEGER	read-only	The filter ID to identify a filter entry.
IP snRtIpRipRouteFilterIpAddr	1.3.6.1.4.1.1991.1.2.3.4.1.3	IpAddress	read-write	Route IP address to compare with any route IP addresses in a ip rip packet. IP address 0.0.0.0 always compare equals to any route IP addresses in any ip rip packets.
INT snRtIpRipRouteFilterRowStatus	1.3.6.1.4.1.1991.1.2.3.4.1.5	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an exsisting row If the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative. valid(2).....the row exists and is valid
IP snRtIpRipRouteFilterSubnetMask	1.3.6.1.4.1.1991.1.2.3.4.1.4	IpAddress	read-write	Subnet mask to apply to the route IP address in a ip rip packet, the result is compared to snRtIpRipRouteFilterIpAddr. If snRtIpRipRouteFilterIpAddr is 0.0.0.0, this subnet mask value is ignored.
snRtIpRipRouteFilterTable	1.3.6.1.4.1.1991.1.2.3.4		not-accessible	ip rip route filter table.
INT snRtIpRipSetAllPortConfig	1.3.6.1.4.1.1991.1.2.3.1.5	INTEGER	read-write	The value of this object is an index number of a snRtIpRipPortConfigTable row (i.e. snRtIpRipPortConfigPortIndex), which is the selected row to copy all of its read-writable data (i.e. snRtIpRipPortVersion and snRtIpRipPortPoisonReverse) to the rest of the rows in snRtIpRipPortConfigTable. Note: prior setting this object, all the intended data of the given row of the table must be set. Otherwise, the current data of the row will be used to set the entire ip rip port configuration table. The previous setting will be overwritten by the new one.
INT snRtIpRipUpdateTime	1.3.6.1.4.1.1991.1.2.3.1.2	INTEGER	read-write	Ip rip update interval in seconds.
INT snRtIpSetAllPortConfig	1.3.6.1.4.1.1991.1.2.2.1.12	INTEGER	read-write	The value of this object is an index number of a snRtIpPortConfigTable row (i.e. snRtIpPortConfigPortIndex), which is the selected row to copy all of its read-writable data (i.e. snRtIpPortMtu and snRtIpPortEncap) to the rest of the rows in snRtIpPortConfigTable. Note: prior setting this object, all the intended data of the given row of the table must be set. Otherwise, the current data of the row will be used to set the entire ip interface configuration table. The previous setting will be overwritten by the new one.
RTR snRtIpSourceRoute	1.3.6.1.4.1.1991.1.2.2.1.21	RtrStatus	read-write	Enable/Disable source routing support, ability to drop the source routing packets.
IP snRtIpStaticRouteDest	1.3.6.1.4.1.1991.1.2.2.2.1.2	IpAddress	read-write	Destination IP address. 0.0.0.0 for default route.
INT snRtIpStaticRouteDistance	1.3.6.1.4.1.1991.1.2.2.2.1.7	INTEGER	read-write	Administration distance.
snRtIpStaticRouteEntry	1.3.6.1.4.1.1991.1.2.2.2.1		not-accessible	An entry in the IP static route table.
INT snRtIpStaticRouteIndex	1.3.6.1.4.1.1991.1.2.2.2.1.1	INTEGER	read-only	The table index for a static route entry.
IP snRtIpStaticRouteMask	1.3.6.1.4.1.1991.1.2.2.2.1.3	IpAddress	read-write	Subnet mask associated with the destination IP address. 0.0.0.0 for default route mask.
INT snRtIpStaticRouteMetric	1.3.6.1.4.1.1991.1.2.2.2.1.5	INTEGER	read-write	The metrics to next hop router.
IP snRtIpStaticRouteNextHop	1.3.6.1.4.1.1991.1.2.2.2.1.4	IpAddress	read-write	IP address of next hop router that is located on one of the directly attached IP subnet.
ROW snRtIpStaticRouteRowStatus	1.3.6.1.4.1.1991.1.2.2.2.1.6	RowSts	read-write	To create or delete a static route entry.
snRtIpStaticRouteTable	1.3.6.1.4.1.1991.1.2.2.2		not-accessible	IP static/default route table.
snRtIpTraceRoute	1.3.6.1.4.1.1991.1.2.2.10
INT snRtIpTraceRouteControl	1.3.6.1.4.1.1991.1.2.2.10.1.5	INTEGER	read-write	Only 'start' and 'abort' are writable values; 'success', 'failure' and 'inProgress' are readeable (or returned) values. Writing 'start' to this object to initiate the trace route operation. snRtIpTraceRouteDestAddr must have been init- ialized before 'start' is writen. This object will return 'inProgress' after trace route operation has started. During the 'inProgress' state, writing 'abort' to this object will stop the current trace route operation. If the destination address is reached, this object returned 'success'. snRtIpTraceRouteResultTable contains the routes (and the target address) to reach the destination address. If the destination address does not reach, timeout, or ending TTL reached, 'failure' is returned.
snRtIpTraceRouteGeneral	1.3.6.1.4.1.1991.1.2.2.10.1
INT snRtIpTraceRouteMaxTtl	1.3.6.1.4.1.1991.1.2.2.10.1.3	INTEGER	read-write	Maximum TTL value carried in the last probe packet. Value 0 cannot be used for SET operations. This value is returned if traceroute is not running within the system.
INT snRtIpTraceRouteMinTtl	1.3.6.1.4.1.1991.1.2.2.10.1.2	INTEGER	read-write	Minimum TTL value carried in the first probe packet. Value 0 cannot be used for SET operations. This value is returned if traceroute is not running within the system.
snRtIpTraceRouteResult	1.3.6.1.4.1.1991.1.2.2.10.2
IP snRtIpTraceRouteResultAddr	1.3.6.1.4.1.1991.1.2.2.10.2.1.1.2	IpAddress	read-only	The router or the target address of which forms part of the route to reach the destination address.
snRtIpTraceRouteResultEntry	1.3.6.1.4.1.1991.1.2.2.10.2.1.1		not-accessible	An entry of the trace route result table.
INT snRtIpTraceRouteResultIndex	1.3.6.1.4.1.1991.1.2.2.10.2.1.1.1	INTEGER	read-only	The table index for a trace route result entry.
TIK snRtIpTraceRouteResultRoundTripTime1	1.3.6.1.4.1.1991.1.2.2.10.2.1.1.3	TimeTicks	read-only	The round trip time between the first probe packet transmitted and the reponse ICMP packet received.
TIK snRtIpTraceRouteResultRoundTripTime2	1.3.6.1.4.1.1991.1.2.2.10.2.1.1.4	TimeTicks	read-only	The round trip time between the second probe packet transmitted and the reponse ICMP packet received.
snRtIpTraceRouteResultTable	1.3.6.1.4.1.1991.1.2.2.10.2.1		not-accessible	Trace route result table.
IP snRtIpTraceRouteTargetAddr	1.3.6.1.4.1.1991.1.2.2.10.1.1	IpAddress	read-write	Target IP address of which trace route is performed.
INT snRtIpTraceRouteTimeOut	1.3.6.1.4.1.1991.1.2.2.10.1.4	INTEGER	read-write	Time out period (in seconds) to wait for the response from the probe packet (i,e, the ICMP packet). Value 0 cannot be used for SET operations. This value is returned if traceroute is not running within the system.
INT snRtIpTtl	1.3.6.1.4.1.1991.1.2.2.1.11	INTEGER	read-write	The time to live value to be used in IP header of IP packet generated by the box.
snRtStaticArpEntry	1.3.6.1.4.1.1991.1.2.2.5.1		not-accessible	An entry in the IP static arp table.
INT snRtStaticArpIndex	1.3.6.1.4.1.1991.1.2.2.5.1.1	INTEGER	read-only	The table index for a static arp entry.
IP snRtStaticArpIp	1.3.6.1.4.1.1991.1.2.2.5.1.2	IpAddress	read-write	The IP address for a static arp entry.
OCT snRtStaticArpMac	1.3.6.1.4.1.1991.1.2.2.5.1.3	OCTET STRING	read-write	The Mac address for a static arp entry.
POR snRtStaticArpPort	1.3.6.1.4.1.1991.1.2.2.5.1.4	PortIndex	read-write	The port index for a static arp entry.
ROW snRtStaticArpRowStatus	1.3.6.1.4.1.1991.1.2.2.5.1.5	RowSts	read-write	To create or delete a Static Arp entry.
snRtStaticArpTable	1.3.6.1.4.1.1991.1.2.2.5		not-accessible	IP static arp table.
RTR snRtUdpBcastFwdEnable	1.3.6.1.4.1.1991.1.2.2.9.1.1	RtrStatus	read-write	Enable or disable UDP broadcast forwarding service. When UDP broadcast forwarding is enabled, default entries are added to the UDP broadcast forwarding port table. When it is disabled, UDP broadcast forwarding port table is flushed to empty.
snRtUdpBcastFwdPort	1.3.6.1.4.1.1991.1.2.2.9.2
snRtUdpBcastFwdPortEntry	1.3.6.1.4.1.1991.1.2.2.9.2.1.1		not-accessible	An entry of the UDP broadcast forwarding port table.
INT snRtUdpBcastFwdPortIndex	1.3.6.1.4.1.1991.1.2.2.9.2.1.1.1	INTEGER	read-only	The table index for a UDP broadcast forwarding port entry.
INT snRtUdpBcastFwdPortNumber	1.3.6.1.4.1.1991.1.2.2.9.2.1.1.2	INTEGER	read-write	UDP port number for which UDP broadcast forwarding is enabled.
ROW snRtUdpBcastFwdPortRowStatus	1.3.6.1.4.1.1991.1.2.2.9.2.1.1.3	RowSts	read-write	To create or delete a UDP broadcast forwarding port entry.
snRtUdpBcastFwdPortTable	1.3.6.1.4.1.1991.1.2.2.9.2.1		not-accessible	This table contains a list of UDP port numbers for which forwarding UDP broadcast is enabled.
snRtUdpHelper	1.3.6.1.4.1.1991.1.2.2.9.3
IP snRtUdpHelperAddr	1.3.6.1.4.1.1991.1.2.2.9.3.1.1.3	IpAddress	read-write	The UDP helper address. This is the address that UDP packets will be forwarded. It can be a helper address or a subnet broadcast address. But it cannot be 255.255.255.255 or 0.0.0.0.
snRtUdpHelperEntry	1.3.6.1.4.1.1991.1.2.2.9.3.1.1		not-accessible	An entry of the UDP helper table.
INT snRtUdpHelperIndex	1.3.6.1.4.1.1991.1.2.2.9.3.1.1.2	INTEGER	read-only	The table index for a UDP helper entry.
POR snRtUdpHelperPortIndex	1.3.6.1.4.1.1991.1.2.2.9.3.1.1.1	PortIndex	read-only	The port index for a UDP helper entry.
ROW snRtUdpHelperRowStatus	1.3.6.1.4.1.1991.1.2.2.9.3.1.1.4	RowSts	read-write	To create or delete a UDP helper entry.
snRtUdpHelperTable	1.3.6.1.4.1.1991.1.2.2.9.3.1		not-accessible	UDP helper table.
INT snVrrpClearVrrpStat	1.3.6.1.4.1.1991.1.2.12.1.5	INTEGER	read-write	Clear VRRP statistics command.
snVrrpGlobal	1.3.6.1.4.1.1991.1.2.12.1
INT snVrrpGroupOperMode	1.3.6.1.4.1.1991.1.2.12.1.1	INTEGER	read-write	The VRRP is configured on this system either enabled or disabled and the default is disabled mode. disabled(0)..........disable VRRP enabled(1)...........activate VRRP
OCT snVrrpIfAuthPassword	1.3.6.1.4.1.1991.1.2.12.2.1.1.3	OCTET STRING	read-write	The simple text password is allowed if only if the snVrrpIfAuthType type is simpleTextPasswd(1).
INT snVrrpIfAuthType	1.3.6.1.4.1.1991.1.2.12.2.1.1.2	INTEGER	read-write	The authentication type of this interface.
snVrrpIfEntry	1.3.6.1.4.1.1991.1.2.12.2.1.1		not-accessible	The VRRP Interface Entry describes one interface from the viewpoint of VRRP.
INT snVrrpIfMaxNumVridPerIntf	1.3.6.1.4.1.1991.1.2.12.1.3	INTEGER	read-only	Indicates the maximum number of VRID per interface.
INT snVrrpIfMaxNumVridPerSystem	1.3.6.1.4.1.1991.1.2.12.1.4	INTEGER	read-only	Indicates the maximum number of VRID per system.
INT snVrrpIfPort	1.3.6.1.4.1.1991.1.2.12.2.1.1.1	INTEGER	read-only	The IP port of this VRRP interface.
CTR snVrrpIfRxAuthPwdMismatchErrCnts	1.3.6.1.4.1.1991.1.2.12.2.1.1.6	Counter	read-only	The received authentication password mismatched error counts in this interface.
CTR snVrrpIfRxAuthTypeErrCnts	1.3.6.1.4.1.1991.1.2.12.2.1.1.5	Counter	read-only	The received authentication type error counts in this interface.
CTR snVrrpIfRxHeaderErrCnts	1.3.6.1.4.1.1991.1.2.12.2.1.1.4	Counter	read-only	The received Header error counts in this interface.
CTR snVrrpIfRxVridErrCnts	1.3.6.1.4.1.1991.1.2.12.2.1.1.7	Counter	read-only	The received unfound VRID error counts in this interface.
INT snVrrpIfStateChangeTrap	1.3.6.1.4.1.1991.1.2.12.1.2	INTEGER	read-write	Indicates whether the SNMP agent process is permitted to generate VRRP interface state change traps.
snVrrpIfTable	1.3.6.1.4.1.1991.1.2.12.2.1		not-accessible	The VRRP Interface Table describes the interfaces from the viewpoint of VRRP.
snVrrpIntf	1.3.6.1.4.1.1991.1.2.12.2
snVrrpVirRtr	1.3.6.1.4.1.1991.1.2.12.3
INT snVrrpVirRtrActivate	1.3.6.1.4.1.1991.1.2.12.3.1.1.11	INTEGER	read-write	This object specifies the VRRP Router's activate command as: disabled(0)...deactivate this VRRP Router. enabled(1)....activate this VRRP Router.
INT snVrrpVirRtrCfgPriority	1.3.6.1.4.1.1991.1.2.12.3.1.1.4	INTEGER	read-write	The higher the number the higher the priority is. This parameter decides which backup router should becomes the Active Router for the interface. A backup Router with higher priority selected to becomes the Active Router. Therefore, this Object can be set if only if snVrrpVirRtrOwnership is set to backup(2).
INT snVrrpVirRtrCurrDeadInt	1.3.6.1.4.1.1991.1.2.12.3.1.1.26	INTEGER	read-only	Current Dead interval (in 100 milliseconds).
INT snVrrpVirRtrCurrPriority	1.3.6.1.4.1.1991.1.2.12.3.1.1.6	INTEGER	read-only	The higher the number the higher the priority is. This object will be adjusted dynamically with the track priority when the Track Port states first changes from UP to DOWN.
INT snVrrpVirRtrDeadInt	1.3.6.1.4.1.1991.1.2.12.3.1.1.8	INTEGER	read-write	Dead interval (seconds).
snVrrpVirRtrEntry	1.3.6.1.4.1.1991.1.2.12.3.1.1		not-accessible	The VRRP virtual router Entry describes one virtual router from the viewpoint of VRRP.
INT snVrrpVirRtrHelloInt	1.3.6.1.4.1.1991.1.2.12.3.1.1.7	INTEGER	read-write	Time interval between advertisements (seconds).
INT snVrrpVirRtrId	1.3.6.1.4.1.1991.1.2.12.3.1.1.2	INTEGER	read-only	One of the virtual router ID of this VRRP interface.
OCT snVrrpVirRtrIpAddrMask	1.3.6.1.4.1.1991.1.2.12.3.1.1.12	OCTET STRING	read-write	The numbers of IP Addresses of this virtual router of this interface.
INT snVrrpVirRtrOwnership	1.3.6.1.4.1.1991.1.2.12.3.1.1.3	INTEGER	read-write	The ownership of this VRRP router interface can be set either owner(1) or backup(2). VirRtr SNMP-GET returns incomplete(0), it means no IP address has assigned to this VRRP router interface.
INT snVrrpVirRtrPort	1.3.6.1.4.1.1991.1.2.12.3.1.1.1	INTEGER	read-only	The IP port of this VRRP interface.
INT snVrrpVirRtrPreemptMode	1.3.6.1.4.1.1991.1.2.12.3.1.1.9	INTEGER	read-write	This mode controls whether a higher priority Backup router preempts a lower priority Master. The mode with enabled(1) allow preemption and disabled(0) prohibit preemption.
INT snVrrpVirRtrRowStatus	1.3.6.1.4.1.1991.1.2.12.3.1.1.15	INTEGER	read-write	This object is used to create and delete row in the table and control if they are used. The values that can be written are: delete(3)...deletes the row create(4)...creates a new row modify(5)...modifies an existing row VirRtr the row exists, then a SET with value of create(4) returns error 'badValue'. Deleted rows go away immediately. The following values can be returned on reads: noSuch(0)...no such row invalid(1)...Setting it to 'invalid' has the effect of rendering it inoperative.. valid(2)....the row exists and is valid
CTR snVrrpVirRtrRxArpPktDropCnts	1.3.6.1.4.1.1991.1.2.12.3.1.1.16	Counter	read-only	The received VRRP ARP Packet Drop Counts.
CTR snVrrpVirRtrRxHelloIntMismatchCnts	1.3.6.1.4.1.1991.1.2.12.3.1.1.21	Counter	read-only	The counts of the virtual router interface with hello interval mismatch counts.
CTR snVrrpVirRtrRxHigherPriorityCnts	1.3.6.1.4.1.1991.1.2.12.3.1.1.23	Counter	read-only	The counts of the virtual router interface with higher Priority.
CTR snVrrpVirRtrRxIpMismatchCnts	1.3.6.1.4.1.1991.1.2.12.3.1.1.20	Counter	read-only	The received VRRP IP Address mismatching Counts.
CTR snVrrpVirRtrRxIpPktDropCnts	1.3.6.1.4.1.1991.1.2.12.3.1.1.17	Counter	read-only	The received VRRP IP Packet Drop Counts.
CTR snVrrpVirRtrRxNumOfIpMismatchCnts	1.3.6.1.4.1.1991.1.2.12.3.1.1.19	Counter	read-only	The received VRRP Number of IP Addresses mismatching Counts.
CTR snVrrpVirRtrRxPortMismatchCnts	1.3.6.1.4.1.1991.1.2.12.3.1.1.18	Counter	read-only	The received VRRP Port mismatching Counts.
CTR snVrrpVirRtrRxPriorityZeroFromMasterCnts	1.3.6.1.4.1.1991.1.2.12.3.1.1.22	Counter	read-only	The counts of the virtual router interface with Priority zero from the master.
INT snVrrpVirRtrState	1.3.6.1.4.1.1991.1.2.12.3.1.1.10	INTEGER	read-only	This object specifies the VRRP Router's interface state as: init(0)...initialization state. master(1)...master state. backup(2)...backup state.
snVrrpVirRtrTable	1.3.6.1.4.1.1991.1.2.12.3.1		not-accessible	The VRRP virtual router Entry describes one virtual router from the viewpoint of VRRP.
OCT snVrrpVirRtrTrackPortList	1.3.6.1.4.1.1991.1.2.12.3.1.1.27	OCTET STRING	read-write	This object specifies the identity of the physical port whose state is to be monitored. Each port index is a 16-bit integer in big endian order. 8-bit is the slot number, the other 8-bit is the port number. Default value is 0 length octet string. If this object is configured then the Preference Level of this interface will be adjusted dynamically depending on the state of the Track Port. The interface's Preference Level is reduced by value of Preference Level parameter when the Track Port states first changes from UP to DOWN. When the Track Port next comes up the interface's Preference Level is increased by the amount specified by the Preference Level. The router VRRP physical track port membership.
OCT snVrrpVirRtrTrackPortMask	1.3.6.1.4.1.1991.1.2.12.3.1.1.13	OCTET STRING	read-write	This object specifies the identity of the physical port whose state is to be monitored. Each bit is a port of the system. Default value is 0. VirRtr this object is configured then the Preference Level of this interface will be adjusted dynamically depending on the state of the Track Port. The interface's Preference Level is reduced by value of Preference Level parameter when the Track Port states first changes from UP to DOWN. When the Track Port next comes up the interface's Preference Level is increased by the amount specified by the Preference Level. The Chassis/Stackable router VRRP Track port membership. The size of the OCTET STRING for Chassis is 32. The size of the OCTET STRING for Stackable is 4. (It was obsoleted after release 07100, replaced by snVrrpVirRtrTrackPortList)
INT snVrrpVirRtrTrackPriority	1.3.6.1.4.1.1991.1.2.12.3.1.1.5	INTEGER	read-write	The higher the number the higher the priority is. after this object is configured, the snVrrpVirRtrCurrPriority of this interface will be adjusted dynamically with this track priority when the Track Port states first changes from UP to DOWN.
OCT snVrrpVirRtrTrackVifMask	1.3.6.1.4.1.1991.1.2.12.3.1.1.14	OCTET STRING	read-write	This object specifies the identity of the virtual interface whose state is to be monitored. Each bit is a port of the system. Default value is 0. VirRtr this object is configured then the Preference Level of this interface will be adjusted dynamically depending on the state of the Track Port. The interface's Preference Level is reduced by value of Preference Level parameter when the Track Port states first changes from UP to DOWN. When the Track Port next comes up the interface's Preference Level is increased by the amount specified by the Preference Level. The Chassis/Stackable router VRRP Track port membership The size of the OCTET STRING for Chassis is 8. The size of the OCTET STRING for Stackable is 4. (It was obsoleted after release 07100, replaced by snVrrpVirRtrTrackVifPortList)
OCT snVrrpVirRtrTrackVifPortList	1.3.6.1.4.1.1991.1.2.12.3.1.1.28	OCTET STRING	read-write	This object specifies the identity of the virtual interface whose state is to be monitored. Each port index is a 16-bit integer in big endian order. Default value is 0 length octet string. If this object is configured then the Preference Level of this interface will be adjusted dynamically depending on the state of the Track Port. The interface's Preference Level is reduced by value of Preference Level parameter when the Track Port states first changes from UP to DOWN. When the Track Port next comes up the interface's Preference Level is increased by the amount specified by the Preference Level. The router VRRP virtual port track membership.
CTR snVrrpVirRtrTransToBackupStateCnts	1.3.6.1.4.1.1991.1.2.12.3.1.1.25	Counter	read-only	The counts of the virtual router interface transition to backup state.
CTR snVrrpVirRtrTransToMasterStateCnts	1.3.6.1.4.1.1991.1.2.12.3.1.1.24	Counter	read-only	The counts of the virtual router interface transition to master state.

RFC description

Foundry/Ruckus vendor-private MIB defining IP-related managed objects for Foundry SN series switches and routers.

Start monitoring Brocade/Foundry FastIron Layer 3 switch (IPv4 routing/ARP/forwarding) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download FOUNDRY-SN-IP-MIB

What Is FOUNDRY-SN-IP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description