EXTREME-SUMMIT-WM-DOT11-EXTNS-MIB

All MIBs › EXTREME-SUMMIT-WM-DOT11-EXTNS-MIB

Organization: Extreme Networks, Inc.

Last Updated: 2005-10-28

Category: Domain: Wireless, Technology: Wireless, Vendor: Extreme Networks

Description: Extreme Networks Summit WM MIB providing IEEE 802.11 extensions for wireless client and radio management on Summit WM controllers.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is EXTREME-SUMMIT-WM-DOT11-EXTNS-MIB?

EXTREME-SUMMIT-WM-DOT11-EXTNS-MIB is an Extreme Networks vendor MIB providing extension objects layered on top of the standard IEEE802dot11-MIB for Summit WM series wireless LAN controllers and their managed access points. As an extensions module it supplements the base 802.11 MIB with additional radio and client-management attributes specific to Extreme's Summit WM architecture, though no concrete object names were provided in the source data. Conceptually such extension MIBs typically expose radio configuration/status and associated wireless client details, adding monitoring value into radio and client health/performance beyond the base standard's scope. This module explicitly depends on and extends the standard IEEE802dot11-MIB, making it unusable in isolation without the base 802.11 objects it augments. It is deployed in enterprise WLAN environments running Extreme Summit WM controllers where administrators need finer-grained wireless statistics than the base 802.11 MIB provides, and an EXTREME-SUMMIT-WM-DOT11-EXTNS-MIB download is needed alongside the base dot11 MIB to fully populate a MIB browser for this platform.

IPNetwork Monitor allows you to monitor SNMP objects defined in EXTREME-SUMMIT-WM-DOT11-EXTNS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Extreme Networks Summit WM wireless LAN controller/access point

Monitoring Examples

No sample object names were supplied for this module, so a concrete polling scenario can't be responsibly constructed without inventing names. Typically an extension MIB of this kind would be polled alongside standard dot11 counters (client association state, radio channel/power) for the Summit WM's access points, used together with the base 802.11 MIB rather than standalone.

Imported Objects

From EXTREME-SUMMIT-WM-SMI

summitWMMgmt	OBJECT-IDENTITY
summitWMModules	OBJECT-IDENTITY

From IEEE802dot11-MIB

dot11WEPDefaultKeyIndex

OBJECT-TYPE

From IF-MIB

InterfaceIndex
ifIndex	OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
MacAddress
RowStatus
TruthValue

OIDs

OID symbolic	OID numeric	Type	Access	Description
dot11ExtnsMib	1.3.6.1.4.1.1916.5.3.1
dot11Extsmt	1.3.6.1.4.1.1916.5.3.1.1
dot11ExtBSSIDTable	1.3.6.1.4.1.1916.5.3.1.1.1		not-accessible	The dot11ExtBSSIDTable contains a list of the BSS (Basic Service Set) Identifiers supported by each radio, and associates an SSID with with each BSS.
dot11ExtBSSIDEntry	1.3.6.1.4.1.1916.5.3.1.1.1.1		not-accessible	An entry in the BSSID table.
I32 dot11ExtBSSIndex	1.3.6.1.4.1.1916.5.3.1.1.1.1.1	Integer32	read-only	A unique value, greater than zero, that identifies each Basic Service Set Identifier (BSSID) supported by a radio.
MAC dot11ExtBSSID	1.3.6.1.4.1.1916.5.3.1.1.1.1.2	MacAddress	read-only	The Basic Service Set Identifier (BSSID) uniquely identifies a wireless network adapter. In the case of the altitue350, a radio can support up to 8 distinct BSSIDs.
I32 dot11ExtSSIDID	1.3.6.1.4.1.1916.5.3.1.1.1.1.3	Integer32	read-write	SSIDID is a Extreme Summit WM internal numeric identifier for the SSID. This number is meaningless external to the product.
OCT dot11ExtSSID	1.3.6.1.4.1.1916.5.3.1.1.1.1.4	OCTET STRING	read-write	The Service Set Identifier (SSID) is the network name identifying the wireless network to which this adapter belongs.
I32 dot11ExtBSSIDWEPKeyIndex	1.3.6.1.4.1.1916.5.3.1.1.1.1.5	Integer32	read-write	Specifies the WEP default key associated with this BSS from the ieee802dot11 dot11WEPDefaultKeysTable.
T/F dot11ExtSSIDSuppress	1.3.6.1.4.1.1916.5.3.1.1.1.1.6	TruthValue	read-write	When True, the radio will not broadcast the SSID associated with this BSSID in the beacons.
T/F dot11ExtPriorityTrafficHandling	1.3.6.1.4.1.1916.5.3.1.1.1.1.7	TruthValue	read-write	When True, priority traffic handling is enabled for this BSSID.
dot11ExtWEPKeyMappingsTable	1.3.6.1.4.1.1916.5.3.1.1.2		not-accessible	The dot11ExtWEPKeyMappingsTable supports the ability to configure a separate WEP key for each BSS/Station pairing. The WEPKeyMappingValues in this table are logically WRITE-ONLY. Any attempt to read these values will return null or 0.
dot11ExtWEPKeyMappingsEntry	1.3.6.1.4.1.1916.5.3.1.1.2.1		not-accessible	An entry in the dot11ExtWEPKeyMappingsTable.
I32 dot11ExtWEPKeyMappingIndex	1.3.6.1.4.1.1916.5.3.1.1.2.1.1	Integer32	read-only	The auxiliary variable used to identify instances of the columnar objects in the WEP Key Mappings Table.
MAC dot11ExtWEPKeyMappingAddress	1.3.6.1.4.1.1916.5.3.1.1.2.1.2	MacAddress	read-create	The MAC address of the STA for which the values from this key mapping entry are to be used.
T/F dot11ExtWEPKeyMappingWEPOn	1.3.6.1.4.1.1916.5.3.1.1.2.1.3	TruthValue	read-create	Boolean as to whether WEP is to be used when communicating with the dot11WEPKeyMappingAddress STA.
WEP dot11ExtWEPKeyMappingValue	1.3.6.1.4.1.1916.5.3.1.1.2.1.4	WEPKeytype	read-create	A WEP secret key value.
ROW dot11ExtWEPKeyMappingStatus	1.3.6.1.4.1.1916.5.3.1.1.2.1.5	RowStatus	read-create	The status column used for creating, modifying, and deleting instances of the columnar objects in the WEP key mapping Table.
dot11CapabilitiesTable	1.3.6.1.4.1.1916.5.3.1.1.3		not-accessible	The dot11CapabilitiesTable contains the 802.11 protocols that each radio in the accessPoint are capable of supporting.
dot11CapabilitiesEntry	1.3.6.1.4.1.1916.5.3.1.1.3.1		not-accessible	An entry in the dot11CapabilitiesTable.
BIT dot11Capabilities	1.3.6.1.4.1.1916.5.3.1.1.3.1.1	Bits	read-write	Describes the capabilities of a radio, for example the protocol supported.
dot11bConfigTable	1.3.6.1.4.1.1916.5.3.1.1.4		not-accessible	The table contains configuration elements specific to the 802.11b protocol.
dot11bConfigEntry	1.3.6.1.4.1.1916.5.3.1.1.4.1		not-accessible	The dot11bConfigTable contains configuration elements specific to the 802.11b protocol. If an attempt to read the elements is made for a radio which does not support 802.11b, null or 0 will be returned.
T/F dot11bEnabled	1.3.6.1.4.1.1916.5.3.1.1.4.1.1	TruthValue	read-write	When true, 802.1b protocol support is active on this radio.
INT dot11BasicB	1.3.6.1.4.1.1916.5.3.1.1.4.1.2	INTEGER	read-write	Specifies the basic rate set for a 11b or 11b+g radio. When set to basic11b, the radio uses all four 11b rates (1, 2, 5.5 and 11 Mbps) as basic rates. When when set to basic11 the radio uses only the two 11 rates (1 and 2 Mbps) as basic rates.
dot11gConfigTable	1.3.6.1.4.1.1916.5.3.1.1.5		not-accessible	The dot11gConfigTable contains configuration elements specific to the 802.11g protocol. If an attempt to read the elements is made for a radio which does not support 802.11g, null or 0 will be returned.
dot11gConfigEntry	1.3.6.1.4.1.1916.5.3.1.1.5.1		not-accessible	An entry in the dot11gConfigTable.
T/F dot11gEnabled	1.3.6.1.4.1.1916.5.3.1.1.5.1.1	TruthValue	read-write	When true, 802.1g protocol support is active on this radio.
INT dot11gProtectionMode	1.3.6.1.4.1.1916.5.3.1.1.5.1.3	INTEGER	read-write	Configures whether and when to use Protection Mode for the 802.11g transmissions. Protection Mode helps reduce collisions with legacy 802.11b stations at the expense of additional overhead. None specifies that no protection is to be used. Auto specifies that radio will enable protection mode when it detects an 802.11b station. Always specifies that protection mode is always enabled.
INT dot11gProtectionType	1.3.6.1.4.1.1916.5.3.1.1.5.1.4	INTEGER	read-write	Determines whether 802.11g Protection Mode uses a RTS-CTS sequence or a CTS-only protection mechanism when Protection Mode is enabled.
INT dot11gProtectionRate	1.3.6.1.4.1.1916.5.3.1.1.5.1.5	INTEGER	read-write	Specifies the rate to be used by RTS or CTS in protection mode.
INT dot11gBasicG	1.3.6.1.4.1.1916.5.3.1.1.5.1.6	INTEGER	read-write	Specifies the set of basic rates in 11-g-only mode. Default allows all possible basic rates (1, 2, 5.5, 11, 6, 12 and 24 Mbps). Basic11 specifies only 11 rates (1 nad 2 Mbps) as basic. Basic11b specifies all four 11b rates (1, 2, 5.5 and 11 Mbps) as basic. OFDM specifies only OFDM rates (6, 12 and 24 Mbps) as basic.
dot11ExtSmtTable	1.3.6.1.4.1.1916.5.3.1.1.7		not-accessible	Extended settings table.
dot11ExtSmtEntry	1.3.6.1.4.1.1916.5.3.1.1.7.1		not-accessible	An entry in the Extended settings table dot11ExtSmtTable.
INT smtShortPreambleInvoked	1.3.6.1.4.1.1916.5.3.1.1.7.1.1	INTEGER	read-write	Specifies the type of preamble used in an 11b/g radio: always short, always long or automatically selected.
I32 dot11ExtSmtCurrentChannel	1.3.6.1.4.1.1916.5.3.1.1.7.1.2	Integer32	read-write	Specfies the current rdio channel.
OCT dot11ExtSmtMaxBasicRate	1.3.6.1.4.1.1916.5.3.1.1.7.1.3	OCTET STRING	read-write	Specifies the maximum basic rate.
OCT dot11ExtSmtMinBasicRate	1.3.6.1.4.1.1916.5.3.1.1.7.1.4	OCTET STRING	read-write	Specifies the minimum basic rate which is also the minimum operational rate.
OCT dot11ExtSmtMaxOperationalRate	1.3.6.1.4.1.1916.5.3.1.1.7.1.5	OCTET STRING	read-write	Specifies the maximum operational rate.
dot11ExtVlanSmtTable	1.3.6.1.4.1.1916.5.3.1.1.8		not-accessible	This table contains configuration about bridging mode for the radio.
dot11ExtVlanSmtEntry	1.3.6.1.4.1.1916.5.3.1.1.8.1		not-accessible	An entry in dot11ExtVlanSmtTable table.
T/F vlanBridgeMode	1.3.6.1.4.1.1916.5.3.1.1.8.1.1	TruthValue	read-write	When true, bridging mode is enabled on this radio.
I32 vlanTag	1.3.6.1.4.1.1916.5.3.1.1.8.1.2	Integer32	read-write	Integer specifying the VLAN tag. If untagged, returns -1.
dot11ExtAPObjs	1.3.6.1.4.1.1916.5.3.1.2
dot1XConfigTable	1.3.6.1.4.1.1916.5.3.1.2.2		not-accessible	Conceptual table for 802.1X settings required for wireless security.
dot1XConfigEntry	1.3.6.1.4.1.1916.5.3.1.2.2.1		not-accessible	An entry in dot1XConfigTable table.
T/F dot1XEnabled	1.3.6.1.4.1.1916.5.3.1.2.2.1.1	TruthValue	read-write	Enable 802.1X authentication for this BSSID.
U32 dot1XDynamicRekeyingInterval	1.3.6.1.4.1.1916.5.3.1.2.2.1.2	Unsigned32	read-write	This object defines the time period, in seconds, after which the key value must be updated.
T/F dot1XWPA1Enabled	1.3.6.1.4.1.1916.5.3.1.2.2.1.3	TruthValue	read-write	Enables WPA.1 (Wi-Fi Protected Access) on this BSSID
STR dot1XWPAPassphrase	1.3.6.1.4.1.1916.5.3.1.2.2.1.4	DisplayString	read-write	Specifies the WPA passphrase for the BSSID. This element is logically write only. Any attempt to read this element will result in null or 0.
INT dot1XWPACipherType	1.3.6.1.4.1.1916.5.3.1.2.2.1.5	INTEGER	read-write	Defines the encryption algoritms allowed with WPA: only TKIP if tkipOnly or both AES and TKIP if auto.
T/F dot1XWPA2Enabled	1.3.6.1.4.1.1916.5.3.1.2.2.1.6	TruthValue	read-write	When true, WPA v.2 support is enabled.
dot11ExtCounters	1.3.6.1.4.1.1916.5.3.1.4
assocGroupTable	1.3.6.1.4.1.1916.5.3.1.4.1		not-accessible	STA statistics table.
assocGroupEntry	1.3.6.1.4.1.1916.5.3.1.4.1.1		not-accessible	Entry in the STA statistics table.
MAC assocAddress	1.3.6.1.4.1.1916.5.3.1.4.1.1.1	MacAddress	read-only	MAC address associated with the client.
NUM assocIfIndex	1.3.6.1.4.1.1916.5.3.1.4.1.1.2	InterfaceIndex	read-only	Interface index of the radio to which the client is associated.
I32 assocReceivedRSSI	1.3.6.1.4.1.1916.5.3.1.4.1.1.3	Integer32	read-only	Received signal strength for the packets received from this client.
I32 assocTransmittedRSSI	1.3.6.1.4.1.1916.5.3.1.4.1.1.4	Integer32	read-only	Received signal strength averaged for the ACK packets received in response to transmitted packets for this client.
U32 assocReceivedRate	1.3.6.1.4.1.1916.5.3.1.4.1.1.5	Unsigned32	read-only	PHY rate for the packets received from this client.
U32 assocTransmittedRate	1.3.6.1.4.1.1916.5.3.1.4.1.1.6	Unsigned32	read-only	PHY rate used to transmit packets for this client.
C64 assocReceivedFrameCount	1.3.6.1.4.1.1916.5.3.1.4.1.1.7	Counter64	read-only	Frames received from this client.
C64 assocTransmittedFrameCount	1.3.6.1.4.1.1916.5.3.1.4.1.1.8	Counter64	read-only	Frames transmitted for this client.
C64 assocReceiveErrors	1.3.6.1.4.1.1916.5.3.1.4.1.1.9	Counter64	read-only	Frames received with errors from this client.
C64 assocTransmitErrors	1.3.6.1.4.1.1916.5.3.1.4.1.1.10	Counter64	read-only	Frames transmitted with errors (not acknowledged) for this cleint.
C64 assocTransmitBytes	1.3.6.1.4.1.1916.5.3.1.4.1.1.11	Counter64	read-only	Bytes transmitted for this client.
C64 assocReceiveBytes	1.3.6.1.4.1.1916.5.3.1.4.1.1.12	Counter64	read-only	Bytes received from this client.
assocCountersTable	1.3.6.1.4.1.1916.5.3.1.4.2		not-accessible	STA association statistics table.
assocCountersEntry	1.3.6.1.4.1.1916.5.3.1.4.2.1		not-accessible	Entry in the STA association statistics table.
C64 assocAuthenticationCount	1.3.6.1.4.1.1916.5.3.1.4.2.1.1	Counter64	read-only	Number of authentications for this client.
C64 assocDeauthenticationCount	1.3.6.1.4.1.1916.5.3.1.4.2.1.2	Counter64	read-only	Number of deauthentications for this client.
C64 assocAssociationCount	1.3.6.1.4.1.1916.5.3.1.4.2.1.3	Counter64	read-only	Number of associations for this client.
C64 assocDeassociationCount	1.3.6.1.4.1.1916.5.3.1.4.2.1.4	Counter64	read-only	Number of deassociations for this client.
C64 assocReassociationCount	1.3.6.1.4.1.1916.5.3.1.4.2.1.5	Counter64	read-only	Number of reassociations for this client.
dot11ExtConformance	1.3.6.1.4.1.1916.5.3.1.5
summitWMDot11ExtModule	1.3.6.1.4.1.1916.5.3.1.5.1			EXTREME-SUMMIT-WM-DOT11-EXTNS module compliance.
summitWMDot11ExtGroups	1.3.6.1.4.1.1916.5.3.1.5.2			Extreme summit WM Dot11-Extns object-group.
summitWMDot11ExtnsMIB	1.3.6.1.4.1.1916.5.5.3			Summit WM Dot11 extensions MIB. This module provides extension objects to the ieee80211 MIB.

RFC description

Summit WM wireless controller 802.11 extensions providing BSSID and SSID management for radio access points.

Start monitoring Extreme Networks Summit WM wireless LAN controller/access point (802.11 extensions) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download EXTREME-SUMMIT-WM-DOT11-EXTNS-MIB

What Is EXTREME-SUMMIT-WM-DOT11-EXTNS-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description