| OID symbolic | OID numeric | Type | Access | Description |
|---|
| dnxOT1E1 | 1.3.6.1.4.1.644.2.4.2.4 | | | |
| dnxOT1E1Enterprise | 1.3.6.1.4.1.644.2.4.2.4.0 | | | ERI DNX T1/E1 Enterprise for Alarms/Events |
| NTF oT1E1ConfigTrap | 1.3.6.1.4.1.644.2.4.2.4.0.1 | | | This trap is used to notify a NMS that a user has updated
the configuration for specific T1/E1 Port. |
| oteConfig | 1.3.6.1.4.1.644.2.4.2.4.1 | | | |
| oT1E1ConfigTable | 1.3.6.1.4.1.644.2.4.2.4.1.1 | | not-accessible | This is the Octal T1/E1 Configuration table which consists
of an entry for each of the Octal T1/E1 card's 8 links(ports).
The total number of entries depends on the number of Octal T1/E1
cards in the nest. Changes to the Link Configuration must be made
on a record or row by row basis. This means that any use of the
Set command on writable fields must include the oT1E1CfgCmdStatus
field with a value of 'update' as the last variable in the SET PDU. |
| oT1E1ConfigEntry | 1.3.6.1.4.1.644.2.4.2.4.1.1.1 | | not-accessible | The conceptual row of the Octal T1/E1 Configuration table.
A row in this table cannot be added or deleted, only modified
using the oT1E1CfgCmdStatus field with a value of 'update' as
the last variable in the SET PDU. The oT1E1CfgCmdStatus field must
be included as the last variable in a SET PDU for the action to
take effect. If the oT1E1CfgCmdStatus is missing from the SET PDU,
the GET RESPONSE will contain the SNMP error status of 'genErr' for
and an error index equal to the last variable. |
| ADR oT1E1CfgLinkAddr | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.1 | LinkPortAddress | read-only | This number uniquely identifies an Octal T1/E1 link resource.
This number will be used throughout the system to identify
a unique link. The format is represented using an IP address
syntax (4 byte string). Note that the maximum valid port
number will vary depending on the specified carrier and framing
options. For example, an octal T1/E1 device has 8 ports but the
DS3 has 28 ports.
The 1st byte is reserved for future Nest Number use
The 2nd byte represents the Slot Number (1-11)
The 3rd byte represents the Port Number (1-32)
The 4th byte is reserved for future use |
| I32 oT1E1CfgResource | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.2 | Integer32 | read-only | Uniquely identifies an Octal T1/E1 link in the system.
This number is provided as key to allow the manager to
map this entry to a corresponding Resource Table entry. |
| STR oT1E1CfgLinkName | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.3 | DisplayString | read-write | This is the user friendly text name to identify the link. |
| POR oT1E1Status | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.4 | PortStatus | read-write | Dictates the current status of the port, in-service or
out-of-service. |
| INT oT1E1ClearT1E1 | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.5 | INTEGER | read-write | Determines if the port supports T1 or E1 unframed. |
| INT oT1E1LineType | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.6 | INTEGER | read-write | Determines the type of framing used on the line. Choose between
E1 (Europeon) or T1 type framing options. When value of oT1E1ClearT1E1
is set to unframed (2), the only valid framing options are:
e1-unframed (5)
t1-b8zs-unframed (10)
t1-ami-unframed (11) |
| FUN oT1E1NetLoop | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.7 | FunctionSwitch | read-write | Determines whether or not the module should respond to loop
diagnostic commands received from the network supplier. Select
'enable' unless the commands are to be passed to another T1/E1
device. |
| DEC oT1E1YelAlrm | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.8 | DecisionType | read-write | Causes the module to discard data and send a yellow alarm if it
is in a red alarm condition after the set recover time period.
'Yes' must be chosen if the network supplier is a common carrier,
such as a telephone company. |
| INT oT1E1RecoverTime | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.9 | INTEGER | read-write | This is the red alarm timeout value. Determines the amount
of seconds the port will wait to stop sending the yellow alarm
when coming out of a red alarm condition. This field does not
apply to E1 links. |
| INT oT1E1IdleCode | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.10 | INTEGER | read-write | Determines the whether the data that will be transmitted over
the unused Ds0s will be 'idle' or 'busy' (all 1's). |
| INT oT1E1EsfFormat | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.11 | INTEGER | read-write | Determines the type of ESF network commands the T-1 link
will respond to. It has no meaning for D4 networks. With ESF
networks, this information must be obtained from the network
supplier. ESF does not apply to E1 links. |
| INT oT1E1CfgLBO | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.12 | INTEGER | read-write | Determines the type of Line Build Out (LBO) used on the link.
Choose between short haul or long haul designations but this varies
between T1 & E1. E1 LBO is defined by authentication of signal
presented to receiving circuitry while T1 LBO can be defined by
cable length or signal.
e1-shortHaul-0-6db (1) 0 to -6 decibel loss
e1-longHaul-0-34db (2) 0 to -34 decibel loss
t1-longHaul-0-0db (3) 0.0 decibel loss
t1-longHaul-7-5db (4) 0.0 to -7.5 decibel loss
t1-longHaul-15-0db (5) 0.0 to -15.0 decibel loss
t1-longHaul-22-5db (6) 0.0 to -22.5 decibel loss
t1-shortHaul-0-133ft (7) 0 to 133 feet of cable
t1-shortHaul-133-266ft (8) 133 to 266 feet of cable
t1-shortHaul-266-399ft (9) 266 to 399 feet of cable
t1-shortHaul-399-533ft (10) 399 to 533 feet of cable
t1-shortHaul-533-655ft (11) 533 to 655 feet of cable |
| LIN oT1E1CfgCmdStatus | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.13 | LinkCmdStatus | read-write | The command status for this link configuration row/record.
The value used in a SET will be replaced by a response
value in the GET RESPONSE indicating success or failure.
Default Response State used in GET RESPONSE Command
ready-for-command (0)
initial default status for a row
T1/E1 Link Commands used in SET Command (1..99)
update-link-config(1)
Change existing Link Configuration
inServiceAll (7)
Change Link Status to in-service for all 8 links.
copyToAll (9)
Copy T1 Link configuration to all other links
within the same device
outOfServiceAll (12)
Change Link Status to out-of-service for all 8 links.
Response States used in GET RESPONSE Command (100..199)
update-successful (101)
Link data has been successfully changed
insvc-successful (107)
All Links have been successfully placed In Service
copy-successful (109)
T1 Link data has been successfully copied to other links
oos-successful (112)
All Links have been successfully placed Out of Service
T1/E1 Link Config Error Codes used in GET RESPONSE Command (200..699)
err-general-link-config-error (400)
Unknown link configuration error occurred
err-invalid-link-status (401)
Unrecognized link status setting
err-invalid-link-framing (402)
Line framing type not valid for link type
err-invalid-link-command (403)
Unrecognized link command-action
err-invalid-link-lbo (404)
Line Build Out option not valid for link type
err-invalid-esf-format (405)
ESF type not applicable to link type
err-invalid-network-loop (410)
Unrecognized network loop setting
err-invalid-yellow-alrm (411)
Unrecognized yellow alarm setting
err-invalid-red-timeout (412)
Unrecognized red alarm timeout
err-invalid-idle-code (413)
Unrecognized idle code
err-device-in-standby (414)
Can't change config for designated Standby device
err-invalid-link-bits (427)
Reserved E1 National bits must be left at zero.
err-data-locked-by-another-user (450)
Another administrative user is making changes to this
part of the system via a terminal session. Check Event
Log for user name
err-snmp-parse-failed (500)
Agent could not parse variable
err-invalid-snmp-type (501)
Variable ASN type does not match Agent defined type
err-invalid-snmp-var-size (502)
Variable size is too big |
| DEC oT1E1Gr303Facility | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.14 | DecisionType | read-only | Enables link to be configured as a Gr303 Facility |
| ONE oT1E1NationalBits | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.15 | OneByteField | read-write | Enables E1 National S-bits to be set to zero or one.
This single byte field can be changed to set the values
of the E1 NFA byte in odd frames as depicted below:
sa8 sa7 sa6 sa5 sa4 reserved bits
--- --- --- --- --- -------------
1 1 1 1 1 0 0 0 = F8 (default)
Values should be entered in Hex. If reserved bits are changed,
an error code (427) will be returned in the command status. |
| ONE oT1E1InterNational | 1.3.6.1.4.1.644.2.4.2.4.1.1.1.16 | OneByteField | read-write | Enables InterNational S(i) Spare bit to be set to zero or one.
This single byte field can be changed to set the values
of the Bit 1 of TS0 G.704 frame as depicted below:
reserved bits S(i)
-------------------------- -----
0 0 0 0 0 0 0 1 = 01 (default)
Values should be entered in Hex. If reserved bits are changed,
an error code (427) will be returned in the command status. |
| oteDiag | 1.3.6.1.4.1.644.2.4.2.4.2 | | | |
| eriDNXOctalT1E1MIB | 1.3.6.1.4.1.644.3.2 | | | The ERI Enterprise MIB Module for the DNX T1/E1 ports. |
