ENTERASYS-IP-SLA-MIB

All MIBs › ENTERASYS-IP-SLA-MIB

Organization: Enterasys Networks, Inc

Last Updated: 2013-02-06

Category: Technology: SLA/OAM, Vendor: Enterasys/Cabletron

Description: Enterasys Networks MIB for configuring IP SLA probe entries and retrieving round-trip-time and jitter measurement results.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ENTERASYS-IP-SLA-MIB?

ENTERASYS-IP-SLA-MIB is a proprietary Enterasys Networks MIB for configuring IP Service Level Agreement (SLA) probes that actively measure network performance, comparable in purpose to Cisco's IP SLA feature. It exposes global capacity objects for how many SLA config and data entries the device supports, plus a configuration table defining each probe's type, destination address/port, and probe name. Its monitoring value is performance measurement: results gathered by these probes (round-trip time and jitter, i.e., packet delay variation) let an administrator verify whether a service provider is meeting contracted SLA obligations, functioning as an active performance-monitoring feature rather than passive interface counters. It is a vendor-specific feature MIB with no stated dependency on a standard IETF IP-SLA MIB. It is deployed on Enterasys/Extreme Networks routers and switches used at network edges where WAN or service-provider SLA compliance needs to be actively verified. Engineers can download the ENTERASYS-IP-SLA-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ENTERASYS-IP-SLA-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Enterasys/Extreme Networks router or switch

Monitoring Examples

An administrator would configure a probe via etsysIpSlaConfigTable/etsysIpSlaConfigEntry, setting etsysIpSlaConfigType, etsysIpSlaConfigDestType, etsysIpSlaConfigDestAddr, and etsysIpSlaConfigDestPort to target a remote SLA responder, then monitor etsysIpSlaEntriesInUse and etsysIpSlaDataEntriesInUse against etsysIpSlaMaxEntries and etsysIpSlaMaxDataEntries to ensure the device has not run out of probe capacity. The resulting round-trip-time and jitter data (reported elsewhere in the MIB's data tables) would be trended over time to detect a WAN link degrading beyond the provider's contracted SLA thresholds. etsysIpSlaConfigProbeName lets operators label probes meaningfully in a large-scale monitoring deployment.

What Can Be Monitored

configured SLA probe entries in use
SLA probe destination address/port
probe type and name
round-trip time / jitter measurement capacity

Imported Objects

From ENTERASYS-MIB-NAMES

etsysModules

OBJECT-IDENTITY

From INET-ADDRESS-MIB

InetAddress
InetAddressType
InetPortNumber

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Gauge32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowStatus

How to Use in IPNetwork Monitor

Example using etsysIpSlaEntriesInUse OID:

Select an Enterasys Networks router/Layer 3 switch (legacy, later Extreme Networks) (IP SLA active probing) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type etsysIpSlaEntriesInUse into the Find box to locate it in the OID tree, then select it and click OK. The number of IP SLA entries currently configured within the system. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Gauge32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
etsysIpSla	1.3.6.1.4.1.5624.1.2.94.1
U32 etsysIpSlaBucketIndex	1.3.6.1.4.1.5624.1.2.94.1.2.5.1.1	Unsigned32	not-accessible	A value that identifies a set of RTT data. The value of this object is influenced by the etsysIpSlaCollectionType. If the collection type is 'summary', the value of this object is one. There is only one RTT summary per data collection. If the collection type is 'distribution' the value of this object represents the distribution index. There is an associated entry in the etsysIpSlaDistDataTable. If the collection type is 'history', the value of this object is in the range of one to etsysIpSlaConfigHistoryBuckets.
U32 etsysIpSlaBucketTime	1.3.6.1.4.1.5624.1.2.94.1.2.5.1.2	Unsigned32	read-only	The time the first RTT data was stored in the bucket. This value is expressed in seconds since the Epoch (Jan 1, 1970).
etsysIpSlaCollectionEntry	1.3.6.1.4.1.5624.1.2.94.1.2.3.1		not-accessible	An entry (conceptual row) in the etsysIpSlaCollectionTable.
etsysIpSlaCollectionGroup	1.3.6.1.4.1.5624.1.2.94.2.1.3			This group defines the objects required to support the data collections for an IP SLA entry.
U32 etsysIpSlaCollectionIndex	1.3.6.1.4.1.5624.1.2.94.1.2.3.1.2	Unsigned32	not-accessible	A value that uniquely identifies a collection of data for the IP SLA entry.
G32 etsysIpslaCollectionNumHops	1.3.6.1.4.1.5624.1.2.94.1.2.3.1.5	Gauge32	read-only	This is the total number of hops per path in this collection of data.
G32 etsysIpSlaCollectionNumPaths	1.3.6.1.4.1.5624.1.2.94.1.2.3.1.4	Gauge32	read-only	This is the total number of paths available to this collection of data.
U32 etsysIpSlaCollectionStartTime	1.3.6.1.4.1.5624.1.2.94.1.2.3.1.3	Unsigned32	read-only	The start time of the test for this collection of data. This value is expressed in seconds since the Epoch (Jan 1, 1970).
etsysIpSlaCollectionTable	1.3.6.1.4.1.5624.1.2.94.1.2.3		not-accessible	This table provides generic information about the data collections stored in the IP SLA entry. A new collection begins at the beginning of each test.
INT etsysIpSlaCollectionType	1.3.6.1.4.1.5624.1.2.94.1.2.3.1.1	INTEGER	not-accessible	This identifies the collection type for this row entry. Each collection will have the 'summary' data. If the etsysIpSlaConfigDistributionCount is not zero, the collection will have a 'distribution' set of data. If the etsysIpSlaConfigHistoryCollections is not zero, the collection will have a 'history' set of data. summary(1) - The row entry data corresponds to the cumulative statistics gathered during a test. distribution(2) - The row entry data corresponds to the statistical distribution of the round-trip- time data. history(3) - The row entry data corresponds to a storage history collection of data.
etsysIpSlaCompliance	1.3.6.1.4.1.5624.1.2.94.2.2.1			The compliance statement for devices that support etsysIpSla.
etsysIpSlaCompliances	1.3.6.1.4.1.5624.1.2.94.2.2
IP etsysIpSlaConfigDestAddr	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.4	InetAddress	read-create	The destination address of the host. The IP SLA entry collects the data specified in etsysIpSlaConfigType for packets sent to this host.
INE etsysIpSlaConfigDestPort	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.5	InetPortNumber	read-create	The port number of the service on the destination host. The 'icmpTs' entries MUST use the default value of zero.
IPt etsysIpSlaConfigDestType	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.3	InetAddressType	read-create	The address family of the destination host specified in etsysIpSlaConfigDestAddr.
U32 etsysIpSlaConfigDistributionCount	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.16	Unsigned32	read-create	The number of statistical distributions to keep data for. This object only accumulates round-trip-time data calculations. This objects works in conjunction with the etsysIpSlaConfigDistributionInterval object. The last interval accumulates statistical distributions for all the entries from its interval start point to infinity (maximum value for a 32-bit integer).
U32 etsysIpSlaConfigDistributionInterval	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.17	Unsigned32	read-create	The statistical distribution interval. Example: etsysIpSlaConfigDistributionCount = 5 etsysIpSlaConfigDistributionInterval = 20 milliseconds Distribution 1 : Distribution 2 : Distribution 3 : Distribution 4 : Distribution 5 :
etsysIpSlaConfigEntry	1.3.6.1.4.1.5624.1.2.94.1.2.1.1		not-accessible	An entry (conceptual row) in the etsysIpSlaConfigTable.
etsysIpSlaConfigGroup	1.3.6.1.4.1.5624.1.2.94.2.1.2			This group defines the objects used to configure and schedule the entries used by the Enterasys IP SLA functionality.
U32 etsysIpSlaConfigHistoryAgeout	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.14	Unsigned32	read-create	The length of time a history collection remains in memory. The application reclaims the history collection's memory when it ages out. A value of zero means the history collection does not ageout.
U32 etsysIpSlaConfigHistoryBuckets	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.10	Unsigned32	read-create	The number of history buckets to maintain per history collection. Each bucket contains statistical information from the test.
INT etsysIpSlaConfigHistoryBucketType	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.11	INTEGER	read-create	The history bucket type. This determines the depth of each bucket. static(1) - A static bucket type indicates the depth of each bucket is fixed. The depth is specified in etsysIpSlaConfigHistorySamples. timed(2) - A timed bucket has a variable bucket depth. The etsysIpSlaConfigHistoryInterval specifies the total time for the bucket. To estimate the depth of the bucket, multiply the history interval by the expected number of received packets per second.
U32 etsysIpSlaConfigHistoryCollections	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.9	Unsigned32	read-create	The number of history collections to store in memory. A new collection begins with the start of each test. The etsysIpSlaScheduleTable dictates when tests start and stop. Modifying this value from a larger value to a smaller value causes the difference to be removed from memory. The collection with higher index values are removed. The history collections are found in the etsysIpSlaRttDataTable and the etsysIpSlaPdvDataTable using a etsysIpSlaCollectionType of 'history'.
U32 etsysIpSlaConfigHistoryInterval	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.13	Unsigned32	read-create	Specifies the length of time data should be continuously stored in the same bucket. Modifying this value changes the time for the current and future buckets. Previous buckets MUST NOT be modified. Data in the current bucket MUST NOT be altered either. This object is only valid when etsysIpSlaConfigHistoryBucketType is 'timed'. An 'inconsistentValue' return code is returned for a set operation when the type is other than 'timed'.
U32 etsysIpSlaConfigHistorySamples	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.12	Unsigned32	read-create	Specifies the static depth of each bucket. Modifying this value changes the depth for current and future buckets. Previous buckets MUST NOT be modified. This object is only valid when etsysIpSlaConfigHistoryBucketType is 'static'. An 'inconsistentValue' return code is returned for a set operation when the type is other than 'static'.
INT etsysIpSlaConfigHistoryWrap	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.15	INTEGER	read-create	Specifies whether to replace the oldest history collection with a newer data set, or stop collecting history data when the collection limit is reached. wrap(1) - When the history collection reaches its limit, the oldest history collection data is replaced with the newer data set. noWrap(2) - Once the history collection limit is reached, no new history collections are stored unless they age out.
U32 etsysIpSlaConfigHopCount	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.8	Unsigned32	read-create	The number of hops per path the entry keeps data for. Only the first etsysIpSlaConfigHopCount will be kept, additional hops along the path are ignored. This object is only valid when the etsysIpSlaConfigType is 'echo'. An 'inconsistentValue' return code is returned for a set operation when the type is other than 'echo'.
U32 etsysIpSlaConfigIndex	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.1	Unsigned32	not-accessible	A value that uniquely identifies a row in the etsysIpSlaConfigTable. This is the primary index used for all tables that have an association with an IP SLA entry.
U32 etsysIpSlaConfigPathCount	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.7	Unsigned32	read-create	A packet may traverse different routes to a destination host. This value specifies how many different paths to keep track of. Only the first etsysIpSlaConfigPathCount will be kept, additional detected paths are ignored. This object is only valid when the etsysIpSlaConfigType is 'echo'. An 'inconsistentValue' return code is returned for a set operation when the type is other than 'echo'.
STR etsysIpSlaConfigProbeName	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.6	SnmpAdminString	read-create	The name of the user configured probe this entry references. If this value is the empty string, the default probe assigned to the IP SLA application is used for running tests.
U32 etsysIpSlaConfigStatisticsCollections	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.18	Unsigned32	read-create	The number of statistical collections to store in memory. Each collection consists of the summary of results and the statistical distribution data. The summary of results consists of the round-trip-time and, if applicable, the packet delay variation data. A new collection begins with the start of each test. The etsysIpSlaScheduleTable dictates when tests start and stop. The collection automatically wraps back to one when the collection limit, configured by this object, is reached. The statistics stored in the collection are cleared prior to starting a new test. Modifying this value from a larger to a smaller value causes the difference to be removed from memory. The collections with the higher index values are removed. The statistical collections are found in the etsysIpSlaRttDataTable and the etsysIpSlaPdvDataTable.
ROW etsysIpSlaConfigStatus	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.19	RowStatus	read-create	This object permits management of the table by facilitating actions such as row creation and deletion. Creation and activation of a conceptual row in this table MUST be performed as a single operation by setting this object to createAndGo(4). Suspension of an active conceptual row is not supported. Consequently, setting this object to createAndWait(5) or notInService(2) SHALL fail.
etsysIpSlaConfigTable	1.3.6.1.4.1.5624.1.2.94.1.2.1		not-accessible	This table defines the configuration parameters and attributes pertaining to an IP SLA entry. The agent limits the size of this table. The object etsysIpSlaMaxEntries defines the maximum number of entries.
INT etsysIpSlaConfigType	1.3.6.1.4.1.5624.1.2.94.1.2.1.1.2	INTEGER	read-create	The type of the IP SLA entry. echo(1) - Specifies that the IP SLA entry collect the round-trip-time data for a destination host. The IP SLA entry MUST use a probe of type 'icmpTs'. jitter(2) - Specifies that the IP SLA entry collect the packet delay variation (jitter) and round-trip-time data for a destination host. The IP SLA entry MUST use a probe of type 'icmpTs'. Both the source and destination hosts MUST have clock synchorinzation enabled for accurate packet delay variation data.
etsysIpSlaConformance	1.3.6.1.4.1.5624.1.2.94.2
G32 etsysIpSlaDataEntriesInUse	1.3.6.1.4.1.5624.1.2.94.1.1.4	Gauge32	read-only	The number of data constructs currently used within the system Row entries in the etsysIpSlaRttDataTable and the etsysIpSlaPdvDataTable consume this resource.
etsysIpSlaDistDataEntry	1.3.6.1.4.1.5624.1.2.94.1.2.7.1		not-accessible	An entry (conceptual row) in the etsysIpSlaDistDataTable.
etsysIpSlaDistDataTable	1.3.6.1.4.1.5624.1.2.94.1.2.7		not-accessible	This table provides the packet distribution data for the IP SLA entries.
U32 etsysIpSlaDistMaxRange	1.3.6.1.4.1.5624.1.2.94.1.2.7.1.2	Unsigned32	read-only	This is the upper bound value for this statistical distribution segment. The etsysIpSlaConfigDistributionInterval is used to determine this value.
U32 etsysIpSlaDistMinRange	1.3.6.1.4.1.5624.1.2.94.1.2.7.1.1	Unsigned32	read-only	This is the lower bound value for this statistical distribution segment. The etsysIpSlaConfigDistributionInterval is used to determine this value.
etsysIpSlaDistribGroup	1.3.6.1.4.1.5624.1.2.94.2.1.7			This group defines the statistical distribution range data.
G32 etsysIpSlaEntriesInUseEx	1.3.6.1.4.1.5624.1.2.94.1.1.2	Gauge32	read-only	The number of IP SLA entries currently configured within the system.
etsysIpSlaGlobalGroup	1.3.6.1.4.1.5624.1.2.94.2.1.1			This group defines information pertaining to the global resources used by the Enterasys IP SLA functionality.
etsysIpSlaGlobals	1.3.6.1.4.1.5624.1.2.94.1.1
etsysIpSlaGroups	1.3.6.1.4.1.5624.1.2.94.2.1
IP etsysIpSlaHopDestAddr	1.3.6.1.4.1.5624.1.2.94.1.2.4.1.4	InetAddress	read-only	The address of the hop in the path.
IPt etsysIpSlaHopDestType	1.3.6.1.4.1.5624.1.2.94.1.2.4.1.3	InetAddressType	read-only	The address family of the hop in the path.
U32 etsysIpSlaHopIndex	1.3.6.1.4.1.5624.1.2.94.1.2.4.1.2	Unsigned32	not-accessible	This value represents the nth-hop in the path to the destination host identified by etsysIpSlaConfigDestAddr. A value of zero for this object and etsysIpSlaPathIndex represent the destination host.
U32 etsysIpSlaMaxDataEntries	1.3.6.1.4.1.5624.1.2.94.1.1.3	Unsigned32	read-only	The maximum number of data constructs available within the system. Row entries in the etsysIpSlaRttDataTable and the etsysIpSlaPdvDataTable consume this resource.
U32 etsysIpSlaMaxEntries	1.3.6.1.4.1.5624.1.2.94.1.1.1	Unsigned32	read-only	The maximum number of IP SLA entries that can be configured within the system.
etsysIpSlaMIB	1.3.6.1.4.1.5624.1.2.94			This MIB module defines a portion of the SNMP MIB under the Enterasys Networks enterprise OID pertaining to the IP Service Level Agreement (SLA) functionality. This MIB was designed to be used for configuring IP SLA entries, scheduling those entries to run tests, and retrieving the round-trip-time and packet delay variation (jitter) data. Management entities MAY use this data to verify the service provider is meeting its SLA obligation.
etsysIpSlaPathEntry	1.3.6.1.4.1.5624.1.2.94.1.2.4.1		not-accessible	An entry (conceptual row) in the etsysIpSlaPathTable.
etsysIpSlaPathGroup	1.3.6.1.4.1.5624.1.2.94.2.1.4			This group defines the path and hop objects used by the IP SLA entries.
U32 etsysIpSlaPathIndex	1.3.6.1.4.1.5624.1.2.94.1.2.4.1.1	Unsigned32	not-accessible	This value represents a unique path discovered to reach the destination host identified by etsysIpSlaConfigDestAddr. A value of zero for this object and etsysIpSlaHopIndex represent the destination host.
etsysIpSlaPathTable	1.3.6.1.4.1.5624.1.2.94.1.2.4		not-accessible	This table provides the information for the path and hop data of an IP SLA entry.
etsysIpSlaPdvDataEntry	1.3.6.1.4.1.5624.1.2.94.1.2.6.1		not-accessible	An entry (conceptual row) in the etsysIpSlaPdvDataTable.
G32 etsysIpSlaPdvDataMaxNegativeDS	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.18	Gauge32	read-only	The negative PDV values are stored as absolute values. The value of this object is the maximum value from the set of absolute values for packets sent from the destination to the source.
G32 etsysIpSlaPdvDataMaxNegativeSD	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.8	Gauge32	read-only	The negative PDV values are stored as absolute values. The value of this object is the maximum value from the set of absolute values for packets sent from the source to the destination.
G32 etsysIpSlaPdvDataMaxOneWayDS	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.29	Gauge32	read-only	The maximum one-way delay value for packets sent from the destination to the source.
G32 etsysIpSlaPdvDataMaxOneWaySD	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.24	Gauge32	read-only	The maximum one-way delay value for packets sent from the source to the destination.
G32 etsysIpSlaPdvDataMaxPositiveDS	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.13	Gauge32	read-only	The maximum PDV of all positive values for packets sent from the destination to the source.
G32 etsysIpSlaPdvDataMaxPositiveSD	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.3	Gauge32	read-only	The maximum PDV of all positive values for packets sent from the source to the destination.
G32 etsysIpSlaPdvDataMinNegativeDS	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.17	Gauge32	read-only	The negative PDV values are stored as absolute values. The value of this object is the minimum value from the set of absolute values for packets sent from the destination to the source.
G32 etsysIpSlaPdvDataMinNegativeSD	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.7	Gauge32	read-only	The negative PDV values are stored as absolute values. The value of this object is the minimum value from the set of absolute values for packets sent from the source to the destination.
G32 etsysIpSlaPdvDataMinOneWayDS	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.28	Gauge32	read-only	The minimum one-way delay value for packets sent from the destination to the source.
G32 etsysIpSlaPdvDataMinOneWaySD	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.23	Gauge32	read-only	The minimum one-way delay value for packets sent from the source to the destination.
G32 etsysIpSlaPdvDataMinPositiveDS	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.12	Gauge32	read-only	The minimum PDV of all positive values for packets sent from the destination to the source.
G32 etsysIpSlaPdvDataMinPositiveSD	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.2	Gauge32	read-only	The minimum PDV of all positive values for packets sent from the source to the destination.
G32 etsysIpSlaPdvDataNumNegativeDS	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.19	Gauge32	read-only	The total number of negative PDV values for packets sent from the destination to the source.
G32 etsysIpSlaPdvDataNumNegativeSD	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.9	Gauge32	read-only	The total number of negative PDV values for packets sent from the source to the destination.
G32 etsysIpSlaPdvDataNumOneWayDS	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.27	Gauge32	read-only	The total number of one-way delay values for packets sent from the destination to the source.
G32 etsysIpSlaPdvDataNumOneWaySD	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.22	Gauge32	read-only	The total number of one-way delay values for packets sent from the source to the destination.
G32 etsysIpSlaPdvDataNumPositiveDS	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.14	Gauge32	read-only	The total number of positive PDV values for packets sent from the destination to the source.
G32 etsysIpSlaPdvDataNumPositiveSD	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.4	Gauge32	read-only	The total number of positive PDV values for packets sent from the source to the destination.
G32 etsysIpSlaPdvDataSamples	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.1	Gauge32	read-only	The PDV samples that were successfully measured.
G32 etsysIpSlaPdvDataSumNegativeDS	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.20	Gauge32	read-only	The sum of the negative PDV values for packets sent from the destination to the source. The absolute value is returned.
G32 etsysIpSlaPdvDataSumNegativeSD	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.10	Gauge32	read-only	The sum of the negative PDV values for packets sent from the source to the destination. The absolute value is returned.
G32 etsysIpSlaPdvDataSumOneWayDS	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.30	Gauge32	read-only	The sum of the one-way delays for packets sent from the destination to the source.
G32 etsysIpSlaPdvDataSumOneWaySD	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.25	Gauge32	read-only	The sum of the one-way delays for packets sent from the source to the destination.
G32 etsysIpSlaPdvDataSumPositiveDS	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.15	Gauge32	read-only	The sum of the positive PDV values for packets sent from the destination to the source.
G32 etsysIpSlaPdvDataSumPositiveSD	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.5	Gauge32	read-only	The sum of the positive PDV values for packets sent from the source to the destination.
G32 etsysIpSlaPdvDataSumSquareNegativeDS	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.21	Gauge32	read-only	The sum of the squared negative PDV values for packets sent from the destination to the source.
G32 etsysIpSlaPdvDataSumSquareNegativeSD	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.11	Gauge32	read-only	The sum of the squared negative PDV values for packets sent from the source to the destination.
G32 etsysIpSlaPdvDataSumSquareOneWayDS	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.31	Gauge32	read-only	The sum of squares of the one-way delays for packets sent from the destination to the source.
G32 etsysIpSlaPdvDataSumSquareOneWaySD	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.26	Gauge32	read-only	The sum of squares of the one-way delays for packets sent from the source to the destination.
G32 etsysIpSlaPdvDataSumSquarePositiveDS	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.16	Gauge32	read-only	The sum of the squared positive PDV values for packets sent from the destination to the source.
G32 etsysIpSlaPdvDataSumSquarePositiveSD	1.3.6.1.4.1.5624.1.2.94.1.2.6.1.6	Gauge32	read-only	The sum of the squared positive PDV values for packets sent from the source to the destination.
etsysIpSlaPdvDataTable	1.3.6.1.4.1.5624.1.2.94.1.2.6		not-accessible	This table provides the packet delay variation (jitter) data for the IP SLA entry.
etsysIpSlaPdvGroup	1.3.6.1.4.1.5624.1.2.94.2.1.6			This group defines the packet delay variation (jitter) data objects defined for the IP SLA entries used by the Enterasys IP SLA functionality.
G32 etsysIpSlaRttDataAvgDelay	1.3.6.1.4.1.5624.1.2.94.1.2.5.1.5	Gauge32	read-only	The average RTT calculated from the sum of the successful samples.
etsysIpSlaRttDataEntry	1.3.6.1.4.1.5624.1.2.94.1.2.5.1		not-accessible	An entry (conceptual row) in the etsysIpSlaRttDataTable.
G32 etsysIpSlaRttDataMaxDelay	1.3.6.1.4.1.5624.1.2.94.1.2.5.1.6	Gauge32	read-only	The maximum RTT measurement from the successful samples.
G32 etsysIpSlaRttDataMinDelay	1.3.6.1.4.1.5624.1.2.94.1.2.5.1.4	Gauge32	read-only	The minimum RTT measurement from the successful samples.
G32 etsysIpSlaRttDataPktIpTosMismatch	1.3.6.1.4.1.5624.1.2.94.1.2.5.1.13	Gauge32	read-only	The number of reply packets whose IP TOS field mismatched the value in the request.
G32 etsysIpSlaRttDataPktLateArrival	1.3.6.1.4.1.5624.1.2.94.1.2.5.1.11	Gauge32	read-only	The number of packets that arrived late. The RTT for these packets are not included in any calculations.
G32 etsysIpSlaRttDataPktMissing	1.3.6.1.4.1.5624.1.2.94.1.2.5.1.12	Gauge32	read-only	The number of packets lost.
G32 etsysIpSlaRttDataPktOutOfOrder	1.3.6.1.4.1.5624.1.2.94.1.2.5.1.10	Gauge32	read-only	The number of packets that arrived out of order. The RTT for these packets are not included in any calculations.
G32 etsysIpSlaRttDataPktVlanPcpMismatch	1.3.6.1.4.1.5624.1.2.94.1.2.5.1.14	Gauge32	read-only	The number of reply packets whose VLAN PCP field mismatched the value in the request.
G32 etsysIpSlaRttDataSamples	1.3.6.1.4.1.5624.1.2.94.1.2.5.1.3	Gauge32	read-only	The RTT samples that were successfully measured.
G32 etsysIpSlaRttDataSum	1.3.6.1.4.1.5624.1.2.94.1.2.5.1.7	Gauge32	read-only	The summation of the successful RTT samples.
G32 etsysIpSlaRttDataSumSquareHigh	1.3.6.1.4.1.5624.1.2.94.1.2.5.1.9	Gauge32	read-only	The high 32 bits of the sum of squares of the successful RTT samples.
G32 etsysIpSlaRttDataSumSquareLow	1.3.6.1.4.1.5624.1.2.94.1.2.5.1.8	Gauge32	read-only	The low 32 bits of the sum of squares of the successful RTT samples.
etsysIpSlaRttDataTable	1.3.6.1.4.1.5624.1.2.94.1.2.5		not-accessible	This table provides the round-trip-time statistics data for the IP SLA entry.
G32 etsysIpSlaRttDataTxErrors	1.3.6.1.4.1.5624.1.2.94.1.2.5.1.15	Gauge32	read-only	The number transmissions errors.
etsysIpSlaRttGroup	1.3.6.1.4.1.5624.1.2.94.2.1.5			This group defines the round-trip-time data objects defined for the IP SLA entries used by the Enterasys IP SLA functionality.
etsysIpSlaScheduleEntry	1.3.6.1.4.1.5624.1.2.94.1.2.2.1		not-accessible	An entry (conceptual row) in the etsysIpSlaScheduleTable.
U32 etsysIpSlaScheduleRecurrence	1.3.6.1.4.1.5624.1.2.94.1.2.2.1.2	Unsigned32	read-write	This value represents the time between multiple test cycles. This value is the length of time between the end of one test cycle and the start of the next test cycle. A new test cycle SHALL NOT begin while a current cycle is running. Thus, this value SHOULD be greater than the result of the number repetitions multiplied by the sum of the duration and the frequency. If the value is less than the run time of a test cycle, the overlapping test cycles are skipped. For example, if there are two repetitions with a duration of 60 seconds and a frequency of 30 seconds, the test cycle runs for 180 seconds. Notes: Maximum value is 90 days; a value of 86400 is one day. A value of zero indicates this scheduled entry will not repeat its test cycle.
U32 etsysIpSlaScheduleStartTime	1.3.6.1.4.1.5624.1.2.94.1.2.2.1.1	Unsigned32	read-write	This is the initial start time for the entry's set of test cycles. This value is expressed in seconds since the Epoch (Jan 1, 1970). The scheduled entry MUST be cancelled prior to modifying the start time. An 'inconsistentValue' return code is returned for a set operation with a value other than zero if the etsysIpSlaScheduleTestState is NOT 'inactive'. Setting this value to zero cancels the scheduled tests and the etsysIpSlaScheduleTestState transitions to 'inactive'.
etsysIpSlaScheduleTable	1.3.6.1.4.1.5624.1.2.94.1.2.2		not-accessible	This table provides the scheduling parameters and attributes pertaining to an IP SLA entry. The scheduler determines when a test should execute, the length of time that test should run, the number of iterations of the test, and when the next scheduled test should start. An entry MUST exist in the etsysIpSlaConfigTable prior to setting the scheduling objects.
U32 etsysIpSlaScheduleTestDuration	1.3.6.1.4.1.5624.1.2.94.1.2.2.1.4	Unsigned32	read-write	The length of the time each test iteration should execute.
U32 etsysIpSlaScheduleTestFrequency	1.3.6.1.4.1.5624.1.2.94.1.2.2.1.5	Unsigned32	read-write	The length of time between each test iteration.
U32 etsysIpSlaScheduleTestRepetitions	1.3.6.1.4.1.5624.1.2.94.1.2.2.1.3	Unsigned32	read-write	The number of test iterations per test cycle.
INT etsysIpSlaScheduleTestState	1.3.6.1.4.1.5624.1.2.94.1.2.2.1.6	INTEGER	read-only	This is the state of the IP SLA entry test. inactive(1) - The entry is not currently scheduled. complete(2) - The entry has completed its test cycle and will not be rescheduled. running(3) - A test cycle is currently executing. queued(4) - The entry is on scheduler's queue and will start when the entry expires and is removed from the queue. At this point, it's state transitions to 'running'.
STR etsysIpSlaScheduleTestStatus	1.3.6.1.4.1.5624.1.2.94.1.2.2.1.7	SnmpAdminString	read-only	Provides a brief description of the test. The scheduler generates this string based on the test's state and where it is in it's tests cycle. For example, if the etsysIpSlaScheduleTestState is 'queued' and there is 193 seconds prior to the next test cycle starting, the string MAY read: Cycle begins in 193 seconds An implementation MAY choose to always return the empty string.
etsysIpSlaTables	1.3.6.1.4.1.5624.1.2.94.1.2

RFC description

IP Service Level Agreement (SLA) MIB for configuring and monitoring IP SLA tests, collecting round-trip-time and jitter metrics.

Start monitoring Enterasys Networks router/Layer 3 switch (legacy, later Extreme Networks) (IP SLA active probing) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ENTERASYS-IP-SLA-MIB