| OID symbolic | OID numeric | Type | Access | Description |
|---|
| etsysConvergenceEndPointMIB | 1.3.6.1.4.1.5624.1.2.40 | | | This MIB module defines a portion of the SNMP MIB under
Enterasys Networks enterprise OID pertaining to
Convergence End Point management. |
| etsysConvEndPointObjects | 1.3.6.1.4.1.5624.1.2.40.1 | | | |
| etsysConvEndPointConfig | 1.3.6.1.4.1.5624.1.2.40.1.1 | | | |
| ENA etsysConvEndPointGlobalConfigEnable | 1.3.6.1.4.1.5624.1.2.40.1.1.1 | EnabledStatus | read-write | When set to enabled(1) this object activates the current
Convergence End Point configuration.
When set to disabled(2) this MIB SHALL be configurable,
but MUST NOT be applied, all entries will be removed
from the etsysConvEndPointConnMacTable and the
etsysConvEndPointConnPortTable, and any policies that
have been changed as a result of End Point detection
will revert to their default states.
Maintaining the value of this object across agent
reboots is REQUIRED. |
| etsysConvEndPointGlobalConfigTable | 1.3.6.1.4.1.5624.1.2.40.1.1.2 | | not-accessible | This table represents all Convergence End Point types
supported by this entity, and provides a default policy
profile for each Convergence End Point type. |
| etsysConvEndPointGlobalConfigEntry | 1.3.6.1.4.1.5624.1.2.40.1.1.2.1 | | not-accessible | Defines the default policy to be applied when this type of
Convergence End Point is detected or discovered. |
| NUM etsysConvEndPointGlobalEndPointType | 1.3.6.1.4.1.5624.1.2.40.1.1.2.1.1 | ConvEndPointTypes | not-accessible | The Convergence End Point type. The value of this object is
limited to a single enumerated bit in the ConvEndPointTypes
textual convention. |
| I32 etsysConvEndPointGlobalDefaultPolicyIndex | 1.3.6.1.4.1.5624.1.2.40.1.1.2.1.2 | Integer32 | read-write | The policy that should be applied for this type of Convergence
End Point. This value is an etsysPolicyProfileIndex as defined
in the ENTERASYS-POLICY-PROFILE-MIB. If no such policy index
exists, then no policy will be applied when this type of
Convergence End Point is detected or discovered. The value
zero is not a valid etsysPolicyProfileIndex, so zero indicates
that no policy should be applied.
Maintaining the value of this object across system reboots
is REQUIRED. |
| etsysConvEndPointProtocolConfigTable | 1.3.6.1.4.1.5624.1.2.40.1.1.3 | | not-accessible | This table provides control of Convergence End Point detection
and discovery on a per interface and per Convergence End Point
type basis.
Maintaining the values of this table across system reboots
is REQUIRED. |
| etsysConvEndPointProtocolConfigEntry | 1.3.6.1.4.1.5624.1.2.40.1.1.3.1 | | not-accessible | The current Convergence End Point detection and discovery
status for an interface. |
| NUM etsysConvEndPointProtocolEndPointType | 1.3.6.1.4.1.5624.1.2.40.1.1.3.1.1 | ConvEndPointTypes | not-accessible | The Convergence End Point type. |
| ENA etsysConvEndPointProtocolEnable | 1.3.6.1.4.1.5624.1.2.40.1.1.3.1.2 | EnabledStatus | read-write | When set to enabled(1), Convergence End Point detection
and discovery will be enabled on this interface for the
Convergence End Point type specified.
When set to disabled(2), the Convergence End Points that
have been discovered or detected on this interface of the
type specified will be removed from the
etsysConvEndPointConnMacTable and the
etsysConvEndPointConnPortTable.
After all of the End Points have been removed from an
interface the policy on that interface will revert to
its default state. |
| etsysConvEndPointStatus | 1.3.6.1.4.1.5624.1.2.40.1.2 | | | |
| etsysConvEndPointConnMacTable | 1.3.6.1.4.1.5624.1.2.40.1.2.1 | | not-accessible | This table provides information on each of the Convergence
End Points that has been discovered or detected by this
entity.
Maintaining the value of this object across system reboots
is NOT REQUIRED. |
| etsysConvEndPointConnMacEntry | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1 | | not-accessible | Information about an individual Convergence End Point. |
| MAC etsysConvEndPointConnMacMacAddress | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.1 | MacAddress | not-accessible | The MAC address of this Convergence End Point. |
| NUM etsysConvEndPointConnMacPortNumber | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.2 | InterfaceIndex | read-only | The interface on which this Convergence End Point was
detected or discovered. |
| NUM etsysConvEndPointConnMacEndPointType | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.3 | ConvEndPointTypes | read-only | The type of Convergence End Point described by this row. |
| I32 etsysConvEndPointConnMacPolicyIndex | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.4 | Integer32 | read-only | The policy applied for this Convergence End Point. This
value is an etsysPolicyProfileIndex as defined in the
ENTERASYS-POLICY-PROFILE-MIB. If the desired policy does
not currently exist, or never did exist, then a zero MUST
be returned. |
| DAT etsysConvEndPointConnMacDiscoveryTime | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.5 | DateAndTime | read-only | The time and date that this Convergence End Point was
detected or discovered. |
| STR etsysConvEndPointConnMacFirmwareVersion | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.6 | SnmpAdminString | read-only | This is the firmware version of the discovered Convergence
End Point. If this information is not available via the
detection protocol then a zero length string MUST be returned. |
| IPt etsysConvEndPointConnMacInetAddressType | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.7 | InetAddressType | read-only | The address type of the discovered or detected Convergence
End Point. If the address is unknown, then this object
MUST return 'unknown'. |
| IP etsysConvEndPointConnMacInetAddress | 1.3.6.1.4.1.5624.1.2.40.1.2.1.1.8 | InetAddress | read-only | The address of the discovered or detected Convergence End
Point. If the address is unknown, then this object MUST
return a zero length string. |
| etsysConvEndPointConnPortTable | 1.3.6.1.4.1.5624.1.2.40.1.2.2 | | not-accessible | This table provides a mapping from the entities interfaces
to discovered Convergence End Points.
Maintaining the value of this object across system reboots
is NOT REQUIRED. |
| etsysConvEndPointConnPortEntry | 1.3.6.1.4.1.5624.1.2.40.1.2.2.1 | | not-accessible | Information about an individual Convergence End Point. |
| MAC etsysConvEndPointConnPortMacAddress | 1.3.6.1.4.1.5624.1.2.40.1.2.2.1.1 | MacAddress | read-only | The MAC address of the discovered or detected Convergence
End Point. |
| etsysCEPConnMacTable | 1.3.6.1.4.1.5624.1.2.40.1.2.3 | | not-accessible | This table provides information on each of the Convergence
End Points that has been discovered or detected by this
entity.
Maintaining the value of this object across system reboots
is NOT REQUIRED. |
| etsysCEPConnMacEntry | 1.3.6.1.4.1.5624.1.2.40.1.2.3.1 | | not-accessible | Information about an individual Convergence End Point (CEP). |
| NUM etsysCEPConnMacEndPointType | 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.1 | ConvEndPointTypes | read-only | The type of Convergence End Point described by this row. |
| I32 etsysCEPConnMacPolicyIndex | 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.2 | Integer32 | read-only | The policy applied for this Convergence End Point. This
value is an etsysPolicyProfileIndex as defined in the
ENTERASYS-POLICY-PROFILE-MIB. If the desired policy does
not currently exist, or never did exist, then a zero MUST
be returned. |
| DAT etsysCEPConnMacDiscoveryTime | 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.3 | DateAndTime | read-only | The time and date that this Convergence End Point was
detected or discovered. |
| STR etsysCEPConnMacFirmwareVersion | 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.4 | SnmpAdminString | read-only | This is the firmware version of the discovered Convergence
End Point. If this information is not available via the
detection protocol then a zero length string MUST be returned. |
| IPt etsysCEPConnMacInetAddressType | 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.5 | InetAddressType | read-only | The address type of the discovered or detected Convergence
End Point. If the address is unknown, then this object
MUST return 'unknown'. |
| IP etsysCEPConnMacInetAddress | 1.3.6.1.4.1.5624.1.2.40.1.2.3.1.6 | InetAddress | read-only | The address of the discovered or detected Convergence End
Point. If the address is unknown, then this object MUST
return a zero length string. |
| etsysConvEndPointDetection | 1.3.6.1.4.1.5624.1.2.40.1.3 | | | |
| I32 etsysConvEndPointDetectionMaxEntries | 1.3.6.1.4.1.5624.1.2.40.1.3.1 | Integer32 | read-only | This value represents the maximum number of entries
allowed in the etsysConvEndPointDetectionTable. |
| etsysConvEndPointDetectionTable | 1.3.6.1.4.1.5624.1.2.40.1.3.2 | | not-accessible | A table that describes the IP address and IP port based
Convergence End Point detection parameters.
Packets on interfaces that are configured to detect End
Points, via the etsysConvEndPointProtocolConfigTable,
that are defined in this table are inspected to determine
if a Convergence End Point exists on that interface.
Rules applying to Convergence End Point types that are
configured for detection are evaluated according to the
following:
1. If etsysConvEndPointDetectionProtocol does not have
any bits set, this indicates that the port based detection
should not be performed, proceed to step 2. Otherwise
the value in etsysConvEndPointDetectionProtocol is
evaluated against the protocol field in the IP header,
if it is of a, or the, type specified then the destination
port must be between the values of
etsysConvEndPointDetectionPortLow and
etsysConvEndPointDetectionPortHigh, inclusive.
2. If the etsysConvEndPointDetectionAddr is null, this
indicates that no detection address check should be
performed, consider the End Point detected. Otherwise
the value the of etsysConvEndPointDetectionAddr will be
masked with the value of etsysConvEndPointDetectionAddrMask,
via a bitwise AND operation, and this value will be compared
with the destination IP address that has also been masked
with the value of etsysConvEndPointDetectionAddrMask,
via a bitwise AND operation, if they are equal then
consider the End Point detected.
If there are no rows in this table that are in the active
state then the following pseudo entries describe the
behavior of the IP based Convergence End Point detection.
EndPointType siemens
Protocol { { udp, tcp } }
PortLow 4060
PortHigh 4060
AddrType unknown
Addr ''
AddrMaskType unknown
AddrMask ''
EndPointType h323
Protocol { { udp, tcp } }
PortLow 1718
PortHigh 1720
AddrType ipv4
Addr '224.0.1.41'
AddrMaskType ipv4
AddrMask '255.255.255.255'
EndPointType sip
Protocol { { udp, tcp } }
PortLow 5060
PortHigh 5060
AddrType ipv4
Addr '224.0.1.75'
AddrMaskType ipv4
AddrMask '255.255.255.255'
If one or more entries in this table are active the active
entries will define the IP based detection behavior in its
entirety.
Maintaining entries in this table across system reboots is
REQUIRED for entries with an etsysConvEndPointDetectionRowStatus
value of active(1). |
| etsysConvEndPointDetectionEntry | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1 | | not-accessible | Each entry represents a describes parameters for
detecting a Convergence End Point. |
| I32 etsysConvEndPointDetectionRuleIndex | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.1 | Integer32 | not-accessible | The index of this conceptual row. This row represents a
single rule for determining if an incoming IP packet
indicates the presence of a Convergence End Point device.
The lower the numerical value of the index the greater the
precedence of the rule. It is recommended that the lowest
index be configured to most predominate protocol in the
network for greater efficiency. |
| INT etsysConvEndPointDetectionEndPointType | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.2 | INTEGER | read-create | The Convergence End Point device type that a 'hit' on
this rule will indicate the presence of. |
| BIT etsysConvEndPointDetectionProtocol | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.3 | Bits | read-create | The IP protocol type that the following port range
applies to. If no bits are set then the destination
port will not be evaluated as part of the detection
process. |
| I32 etsysConvEndPointDetectionPortLow | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.4 | Integer32 | read-create | The low end of the range of the IP destination port that
will be used for Convergence End Point detection. This
value represents the low value in a range of port numbers
that will be used to indicate this type of Convergence End
Point. This value must be less than or equal to
etsysConvEndPointDetectionPortHigh. |
| I32 etsysConvEndPointDetectionPortHigh | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.5 | Integer32 | read-create | The high end of the range of the IP destination port that
will be used for Convergence End Point detection. This
value represents the high value in a range of port numbers
that will be used to indicate this type of Convergence End
Point. This value must be greater than or equal to
etsysConvEndPointDetectionPortLow. |
| IPt etsysConvEndPointDetectionAddrType | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.6 | InetAddressType | read-create | The destination address type that will be used for Convergence
End Point detection. If the address type is 'unknown', then
this value will not be evaluated as part of the detection
process. |
| IP etsysConvEndPointDetectionAddr | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.7 | InetAddress | read-create | The destination IP address that will be used for Convergence
End Point detection. If this address is null, then this value
will not be evaluated as part of the detection process. |
| IPt etsysConvEndPointDetectionAddrMaskType | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.8 | InetAddressType | read-create | The address type of the mask that will be applied to the
destination IP address as part of the Convergence End Point
detection process. If the address type is 'unknown', then
this value will not be evaluated as part of the detection
process. |
| IP etsysConvEndPointDetectionAddrMask | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.9 | InetAddress | read-create | The destination address mask that will be used for Convergence
End Point detection. If the mask is null, then this value will
not be evaluated as part of the detection process. |
| ROW etsysConvEndPointDetectionRowStatus | 1.3.6.1.4.1.5624.1.2.40.1.3.2.1.10 | RowStatus | read-create | The status of this row as defined by the RowStatus textual
convention.
Rows in this table can only transition to 'notInService',
or to 'active' if the etsysConvEndPointDetectionAddrType
object and the etsysConvEndPointDetectionAddrMaskType
object have the same value, and either their values are
not 'unknown' or there is at least one bit set in the
etsysConvEndPointDetectionProtocol object. |
| etsysCEPDetectionPortConfigTable | 1.3.6.1.4.1.5624.1.2.40.1.3.3 | | not-accessible | A table of per port configuration for Convergence End Point
detection.
Maintaining the value of this object across system reboots
is NOT REQUIRED. |
| etsysCEPDetectionPortConfigEntry | 1.3.6.1.4.1.5624.1.2.40.1.3.3.1 | | not-accessible | An entry containing per port Convergence End Point data.
Only interfaces that are able to detect Convergence End Points
are represented in this table. |
| T/F etsysCEPPortClearUsers | 1.3.6.1.4.1.5624.1.2.40.1.3.3.1.1 | TruthValue | read-write | Setting this object to a value of true(1) will cause
all detected or discovered Convergence End Points to be
removed from the following status tables:
etsysConvEndPointConnMacTable
etsysConvEndPointConnPortTable
etsysCEPConnMacTable
Setting this object to a value of false(2) has no effect. This
object will always return a value of false(2). |
| etsysCEPCdpPortConfigTable | 1.3.6.1.4.1.5624.1.2.40.1.3.4 | | not-accessible | A table of per port configuration for Convergence End Point
detection related to the Cisco CDP protocol. Only ports
that are capable of participating in Cisco CDP protocol are
represented in this table. |
| etsysCEPCdpPortConfigEntry | 1.3.6.1.4.1.5624.1.2.40.1.3.4.1 | | not-accessible | An entry containing per port Convergence End Point data.
Only interfaces that are able to detect Convergence End Points
are represented in this table. |
| I32 etsysCEPCiscoCDPVoicePortVlan | 1.3.6.1.4.1.5624.1.2.40.1.3.4.1.1 | Integer32 | read-write | This object controls the behavior of the remote configuration
of Cisco VOIP phones via Cisco CDP. Setting this object to
a value of -1 will cause the device to not attempt to
remotely configure a Cisco phone using CDP. Setting this
object to a value of 0 will cause the device to configure
the phone to send 802.1p priority tagged frames. A value of
4095 will cause the device to configure the phone to send
untagged frames. A value in the range 1..4094 will cause
the device to configure the phone to send 802.1Q tagged frames
using that value as the VLAN ID encoded in the tag. This object
SHOULD be maintained across device reboots. |
| etsysConvEndPointConformance | 1.3.6.1.4.1.5624.1.2.40.2 | | | |
| etsysConvEndPointGroups | 1.3.6.1.4.1.5624.1.2.40.2.1 | | | |
| etsysConvEndPointGlobalConfigGroup | 1.3.6.1.4.1.5624.1.2.40.2.1.1 | | | Objects which provide global control of the Convergence
End Point features. |
| etsysConvEndPointConfigGroup | 1.3.6.1.4.1.5624.1.2.40.2.1.2 | | | Objects which provide overrides to the global Convergence
End Point controls. |
| etsysConvEndPointDetectionGroup | 1.3.6.1.4.1.5624.1.2.40.2.1.3 | | | Objects that provide configuration information specific to
IP, port, and address based Convergence End Point detection. |
| etsysConvEndPointStatusGroup | 1.3.6.1.4.1.5624.1.2.40.2.1.4 | | | Objects that provide status information for discovered
and detected Convergence End Points. |
| etsysConvEndPointStatusGroup2 | 1.3.6.1.4.1.5624.1.2.40.2.1.5 | | | Objects that provide status information for discovered
and detected Convergence End Points. |
| etsysConvEndPointDetectionGroup2 | 1.3.6.1.4.1.5624.1.2.40.2.1.6 | | | Objects that provide configuration information specific to
IP, port, and address based Convergence End Point detection. |
| etsysConvEndPointPortConfigGroup | 1.3.6.1.4.1.5624.1.2.40.2.1.7 | | | Objects that provide per port control for discovered
and detected Convergence End Points. |
| etsysConvEndPointCiscoVoiceVLANGroup | 1.3.6.1.4.1.5624.1.2.40.2.1.8 | | | Objects that provide per port control for configuring Cisco
VOIP phones via Cisco CDP. |
| etsysConvEndPointCompliances | 1.3.6.1.4.1.5624.1.2.40.2.2 | | | |
| etsysConvEndPointCompliance | 1.3.6.1.4.1.5624.1.2.40.2.2.1 | | | This compliance statement has been deprecated in favor of
the etsysConvEndPointCompliance2 group. |
| etsysConvEndPointCompliance2 | 1.3.6.1.4.1.5624.1.2.40.2.2.2 | | | The compliance statement for entities which implement
the Enterasys Convergence End Point Management MIB. |
| etsysConvEndPointPortConfigCompliance | 1.3.6.1.4.1.5624.1.2.40.2.2.3 | | | The compliance statement for devices that support per port
configuration of Convergence End Point detection and
discovery. |
| etsysConvEndPointCiscoVoiceVLANCompliance | 1.3.6.1.4.1.5624.1.2.40.2.2.4 | | | The compliance statement for devices that support detection
and configuration of Cisco VOIP phones via Cisco CDP. |
