HPN-ICF-RPR-MIB

All MIBs › HPN-ICF-RPR-MIB

Last Updated: 2005-03-16

Description: HPN-ICF-RPR-MIB module

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is HPN-ICF-RPR-MIB?

This MIB manages Resilient Packet Ring (RPR, IEEE 802.17) interfaces on HP/Comware devices, providing an operational table that controls per-interface parameters and reports alarm conditions for the two counter-rotating fiber rings (Outer and Inner) that make up an RPR topology. It belongs to the HP/H3C ICF family and focuses on the physical/link-layer configuration and fault state of ring-based metro network interfaces. Its monitoring value is centered on hardware/link fault detection: because RPR's dual-ring design is meant to survive a single fiber break by wrapping traffic onto the surviving ring, monitoring per-ring alarm status here is critical for confirming that a break has been detected and traffic has failed over correctly rather than silently dropped. It is based on the IEEE 802.17 RPR standard, giving HP/Comware-specific management objects for a standards-defined ring technology. It is deployed on HP/Comware devices used in metro-area or campus ring topologies requiring sub-50ms fiber-cut protection. Network engineers evaluating or troubleshooting this functionality can download the HPN-ICF-RPR-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in HPN-ICF-RPR-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

HP/Comware router/switch with RPR ring interfaces

Monitoring Examples

No specific sample object names were provided for this MIB beyond its module description, so an object-level polling scenario cannot be precisely grounded; conceptually an operator would monitor per-ring (Outer/Inner) operational and alarm status to confirm the RPR ring has not experienced an unprotected fiber break, and check interface parameter settings against the ring's designed configuration.

What Can Be Monitored

RPR interface operational status
ring alarm conditions
outer/inner ring status

Imported Objects

From HPN-ICF-OID-MIB

hpnicfCommon

OBJECT-IDENTITY

From IEEE-802DOT17-RPR-MIB

rprTopoImageEntry	OBJECT-TYPE
rprTopoImageInetAddress	OBJECT-TYPE
rprTopoImageMacAddress	OBJECT-TYPE

From IF-MIB

InterfaceIndex

From INET-ADDRESS-MIB

InetAddress

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-SMI

Counter64
Gauge32

From SNMPv2-TC

MacAddress
RowStatus
TruthValue

How to Use in IPNetwork Monitor

Example using hpnicfRprSrcMacCountReceivedFrames OID:

Select a HP/Comware router/switch with RPR (Resilient Packet Ring) interface as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type hpnicfRprSrcMacCountReceivedFrames into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. Frames received from a particular MAC address of source station. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
hpnicfRpr	1.3.6.1.4.1.11.2.14.11.15.2.60			This MIB manages RPR(Resilient Packet Ring)interfaces by providing an operational table which controls parameters of each RPR interface and reports alarm conditions. A RPR ring is composed of two fiber rings: Outer and Inner.
hpnicfRprObjects	1.3.6.1.4.1.11.2.14.11.15.2.60.1
hpnicfRprMaxmumDefine	1.3.6.1.4.1.11.2.14.11.15.2.60.1.1
hpnicfRprMaxmumDefineTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.1.1		not-accessible	This table contains the specs of RPR ring.
hpnicfRprMaxmumDefineEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.1.1.1		not-accessible	The entry of RPR Maximum Table.
NUM hpnicfRprMaxMumIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.60.1.1.1.1.1	InterfaceIndex	not-accessible	The ifIndex of this RPR interface.
INT hpnicfRprMaxStationNumDefine	1.3.6.1.4.1.11.2.14.11.15.2.60.1.1.1.1.2	INTEGER	read-only	Max station number supported by RPR ring.
G32 hpnicfRprMaxReservedRateDefine	1.3.6.1.4.1.11.2.14.11.15.2.60.1.1.1.1.3	Gauge32	read-only	Max reserved rate supported by each RPR ringlet. An estimate of the interface's current bandwidth in units of 1,000,000 bits per second. If this object reports a value of 'n' then the speed of the interface is somewhere in the range of 'n-500,000' to 'n+499,999'. For interfaces which do not vary in bandwidth or for those where no accurate estimation can be made, this object should contain the nominal bandwidth. For a sub-layer which has no concept of bandwidth, this object should be zero.
hpnicfRprTopoImage	1.3.6.1.4.1.11.2.14.11.15.2.60.1.2
hpnicfRprTopoImageXTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.2.1		not-accessible	This table contains additional objects for the rprTopoImageTable in IEEE-802DOT17-RPR-MIB.
hpnicfRprTopoImageXEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.2.1.1		not-accessible	Each entry contains information specific to a particular station on the ring. The table has at least one entry for the station itself, this entry indicates zero hops on each ringlet.
T/F hpnicfRprTopoImageXWestEdgeStatus	1.3.6.1.4.1.11.2.14.11.15.2.60.1.2.1.1.3	TruthValue	read-only	The current edge status of the west span. If an edge exists,the hpnicfRprTopoImageXWestEdgeStatus is true. Otherwise, the hpnicfRprTopoImageXWestEdgeStatus is false.
T/F hpnicfRprTopoImageXEastEdgeStatus	1.3.6.1.4.1.11.2.14.11.15.2.60.1.2.1.1.4	TruthValue	read-only	The current edge status of the east span. If an edge exists, the hpnicfRprTopoImageXEastEdgeStatus is true. Otherwise, the hpnicfRprTopoImageXEastEdgeStatus is false.
STR hpnicfRprTopoImageXStationName	1.3.6.1.4.1.11.2.14.11.15.2.60.1.2.1.1.5	SnmpAdminString	read-write	The operator assigned station name. The operator can assigned it by hpnicfRprTopoImageXStationName.
hpnicfRprSpanCounters	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3
hpnicfRprSrcMacCountTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.1		not-accessible	The RPR Source Mac Count Table contains the cumulative sum of frames and octects from the particular source station.
hpnicfRprSrcMacCountEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.1.1		not-accessible	An entry in the RPR Source Mac Count Table.
NUM hpnicfRprSrcMacCountIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.1.1.1	InterfaceIndex	not-accessible	The ifIndex of this RPR interface.
MAC hpnicfRprSrcMacCountBySrcAddress	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.1.1.2	MacAddress	not-accessible	MAC address of the source station where the frames come from.
C64 hpnicfRprSrcMacCountReceivedFramesEx	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.1.1.3	Counter64	read-only	Frames received from a particular MAC address of source station.
C64 hpnicfRprSrcMacCountReceivedOctets	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.1.1.4	Counter64	read-only	Octets received from a particular MAC address of source station.
hpnicfRprDestMacCountTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.2		not-accessible	The RPR Destination MAC Count Table contains the cumulative sum of frames and octects to the particular destination station.
hpnicfRprDestMacCountEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.2.1		not-accessible	An entry in the RPR MAC Destination Count Table.
NUM hpnicfRprDestMacCountIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.2.1.1	InterfaceIndex	not-accessible	The ifIndex of RPR interface.
MAC hpnicfRprDestMacCountByDestAddress	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.2.1.2	MacAddress	not-accessible	MAC address of the destination station where the frames are sent to.
C64 hpnicfRprDestMacCountReceivedFrames	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.2.1.3	Counter64	read-only	Frames sent to a particular MAC address of destination station.
C64 hpnicfRprDestMacCountReceivedOctets	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.2.1.4	Counter64	read-only	Octets sent to a particular MAC address of destination station.
hpnicfRprPktDropCountTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3		not-accessible	The RPR Packet Drop Count Table contains the cumulative sum of packets dropped for congestion.
hpnicfRprPktDropCountEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1		not-accessible	An entry in the RPR Packet Drop Count Table.
NUM hpnicfRprPktDropCntIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.1	InterfaceIndex	not-accessible	The ifIndex of this RPR interface.
HPN hpnicfRprPktDropCntRingletID	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.2	HpnicfRprRingletID	not-accessible	The RPR Ringlet of the station through which the packets transmit.
C64 hpnicfRprDownFlowClassAPktDrops	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.3	Counter64	read-only	The total dropped number of Class A packets which transmit down from the host.
C64 hpnicfRprUpFlowClassAPktDrops	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.4	Counter64	read-only	The total dropped number of Class A packets which transmit up to the host.
C64 hpnicfRprDownFlowClassBPktDrops	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.5	Counter64	read-only	The total dropped number of Class B packets which transmit down from the host.
C64 hpnicfRprUpFlowClassBPktDrops	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.6	Counter64	read-only	The total dropped number of Class B packets which transmit up to the host.
C64 hpnicfRprDownFlowClassCPktDrops	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.7	Counter64	read-only	The total dropped number of Class C packets which transmit down from the host.
C64 hpnicfRprUpFlowClassCPktDrops	1.3.6.1.4.1.11.2.14.11.15.2.60.1.3.3.1.8	Counter64	read-only	The total dropped number of Class C packets which transmit up to the host.
hpnicfRprRS	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4
hpnicfRprStaticRSTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1		not-accessible	The RPR Static Ring Selection table contains the static ring selection information by the way of configuration.
hpnicfRprStaticRSEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1.1		not-accessible	An entry in the RPR Static Ring Selection table.
NUM hpnicfRprStaticRSIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1.1.1	InterfaceIndex	not-accessible	The ifIndex of RPR interface.
MAC hpnicfRprStaticRSMacAddress	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1.1.2	MacAddress	not-accessible	The MAC address of the station on the ring.
HPN hpnicfRprStaticRSRingletID	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1.1.3	HpnicfRprRingletID	read-create	The identifier of the ring which frames are sent from one station to another. Ringlet0 refers to outer ring, while ringlet1 does inner.
INT hpnicfRprStaticRSTtl	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1.1.4	INTEGER	read-only	The hops from source station to destination station by the selected ringlet.
T/F hpnicfRprStaticRSValid	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1.1.5	TruthValue	read-only	The flag identify whether the configed ringlet is valid. If it is true, the configed ringlet is valid, otherwise it's invalid.
ROW hpnicfRprStaticRSRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.1.1.6	RowStatus	read-create	The status of this table entry. The status includes createAndGo, active and destroy.
hpnicfRprIpv4DynamicRSTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.2		not-accessible	The RPR Ipv4Dynamic Ring Selection Table that contains the dynamic ring selection information by shortest path.
hpnicfRprIpv4DynamicRSEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.2.1		not-accessible	An entry in the RPR Ipv4Dynamic Ring Selection Table.
NUM hpnicfRprIpv4DynamicRSIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.2.1.1	InterfaceIndex	not-accessible	The ifIndex of RPR interface.
MAC hpnicfRprIpv4DynamicRSMacAddress	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.2.1.2	MacAddress	not-accessible	The Ipv4 MAC address of destination station on the ring.
HPN hpnicfRprIpv4DynamicRSRingletID	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.2.1.3	HpnicfRprRingletID	read-only	The identifier of the ring which frames are sent from the source station to the destination station.
INT hpnicfRprIpv4DynamicRSTtl	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.2.1.4	INTEGER	read-only	The hops from source station to destination station by the selected ringlet.
hpnicfRprIpv6DynamicRSTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.3		not-accessible	The RPR Ipv6 Dynamic Ring Selection Table that contains the Ipv6 ring selection information by dynamic ring selection and static ring selection.
hpnicfRprIpv6DynamicRSEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.3.1		not-accessible	An entry in the RPR Ipv6 Ring Selection Table.
NUM hpnicfRprIpv6DynamicRSIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.3.1.1	InterfaceIndex	not-accessible	The ifIndex of RPR interface.
MAC hpnicfRprIpv6DynamicRSMacAddress	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.3.1.2	MacAddress	not-accessible	The Ipv6 MAC address of the destination station on the ring.
HPN hpnicfRprIpv6DynamicRSRingletID	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.3.1.3	HpnicfRprRingletID	read-only	The identifier of the ring which frames are sent from the source station to the destination station.
INT hpnicfRprIpv6DynamicRSTtl	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.3.1.4	INTEGER	read-only	The hops from source station to destination station by selected ringlet.
hpnicfRprIpv4OverallRSTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.4		not-accessible	The RPR Ipv4 Overall Ring Selection Table that contains the overall and active ring selection infomation by dynamic ring selection and static ring selection.
hpnicfRprIpv4OverallRSEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.4.1		not-accessible	An entry in the RPR Overall Ring Selection Table.
NUM hpnicfRprIpv4OverallRSIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.4.1.1	InterfaceIndex	not-accessible	The ifIndex of RPR interface.
MAC hpnicfRprIpv4OverallRSMacAddress	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.4.1.2	MacAddress	not-accessible	The MAC address of the destination station on the ring.
INT hpnicfRprIpv4OverallRSType	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.4.1.3	INTEGER	read-only	The ring selection item type indicates static or dynamic.
HPN hpnicfRprIpv4OverallRSRingletID	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.4.1.4	HpnicfRprRingletID	read-only	The identifier of the ring which frames are sent from the source station to the destination station.
INT hpnicfRprIpv4OverallRSTtl	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.4.1.5	INTEGER	read-only	The hops from source station to destination station by selected ringlet.
hpnicfRprVrrpRSTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.5		not-accessible	The RPR VRRP Ring Selection Table that contains the ring selection information when the vrrp group is configured.
hpnicfRprVrrpRSEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.5.1		not-accessible	An entry in the RPR VRRP Ring Selection Table.
NUM hpnicfRprVrrpRSIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.5.1.1	InterfaceIndex	not-accessible	The ifIndex of RPR interface.
MAC hpnicfRprVrrpRSVirtualMacAddress	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.5.1.2	MacAddress	not-accessible	The virtual MAC address of the staion in VRRP group.
MAC hpnicfRprVrrpRSMacAddress	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.5.1.3	MacAddress	read-only	The MAC address of the station that is the master in VRRP group.
HPN hpnicfRprVrrpRSRingletID	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.5.1.4	HpnicfRprRingletID	read-only	The identifier of the ring which frames are sent from the source station to the destination station.
INT hpnicfRprVrrpRSTtl	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.5.1.5	INTEGER	read-only	The hops from source station to destination station by selected ringlet.
hpnicfRprDefaultRingIDTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.6		not-accessible	The RPR Default RingID Table specify the default ringID.
hpnicfRprDefaultRingIDEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.6.1		not-accessible	An entry in the RPR Default RingID Table.
NUM hpnicfRprDefaultRingIDIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.6.1.1	InterfaceIndex	not-accessible	The ifIndex of RPR interface.
HPN hpnicfRprDefaultConfigRingletID	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.6.1.2	HpnicfRprRingletID	read-write	The default identifier of the ring configured by user.
HPN hpnicfRprDefaultActiveRingID	1.3.6.1.4.1.11.2.14.11.15.2.60.1.4.6.1.3	HpnicfRprRingletID	read-only	The identifier of the default ring which is active currently. The default ring configured by user may be inactive.
hpnicfRprDefect	1.3.6.1.4.1.11.2.14.11.15.2.60.1.5
hpnicfRprDefectReportTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.5.1		not-accessible	The RPR Defect Report Table that contains the trap information on the ring.
hpnicfRprDefectReportEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.5.1.1		not-accessible	An entry in the RPR Defect Report Table.
NUM hpnicfRprDefectIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.60.1.5.1.1.1	InterfaceIndex	not-accessible	The ifIndex of RPR interface.
BIT hpnicfRprDefectCurrentStatus	1.3.6.1.4.1.11.2.14.11.15.2.60.1.5.1.1.2	Bits	read-only	Indicates the current status of RPR ring. This attribute is used to notify the management system that alarms generate or clear about some RPR ring.
hpnicfRprPriorityMap	1.3.6.1.4.1.11.2.14.11.15.2.60.1.6
hpnicfRprPriority2ClassMapTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.6.1		not-accessible	The Table is for Class Of Service and RPR Service Class Mapping.
hpnicfRprPriority2ClassMapEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.6.1.1		not-accessible	An entry in the COS to Service Class Map Table.
NUM hpnicfRprPriority2ClassMapIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.60.1.6.1.1.1	InterfaceIndex	not-accessible	The ifIndex of RPR interface.
INT hpnicfRprPriority2ClassMapType	1.3.6.1.4.1.11.2.14.11.15.2.60.1.6.1.1.2	INTEGER	not-accessible	The type of Priority,include tag, mpls, ip.
INT hpnicfRprPriorityValue	1.3.6.1.4.1.11.2.14.11.15.2.60.1.6.1.1.3	INTEGER	not-accessible	The priority of tag,mpls and ip, the value range is 0~7.
HPN hpnicfRprPriority2ClassMap	1.3.6.1.4.1.11.2.14.11.15.2.60.1.6.1.1.4	HpnicfRprServiceClass	read-write	The RPR service class.
hpnicfRprRateLimitConfig	1.3.6.1.4.1.11.2.14.11.15.2.60.1.7
hpnicfRprRateLimitConfigTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.7.1		not-accessible	The RPR Rate Limit Configuration Table that contains the rate limit infomation of RPR serviec class.
hpnicfRprRateLimitConfigEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.7.1.1		not-accessible	An entry in the RPR Rate Limit Configuration Table.
NUM hpnicfRprRateLimitConfigIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.60.1.7.1.1.1	InterfaceIndex	not-accessible	The ifIndex of RPR interface.
HPN hpnicfRprRateLimitConfigRingletId	1.3.6.1.4.1.11.2.14.11.15.2.60.1.7.1.1.2	HpnicfRprRingletID	not-accessible	The identifier of the ring of RPR ringlet.
HPN hpnicfRprRateLimitConfigServiceClass	1.3.6.1.4.1.11.2.14.11.15.2.60.1.7.1.1.3	HpnicfRprServiceClass	not-accessible	The RPR service class.
I32 hpnicfRprRateLimitConfigValue	1.3.6.1.4.1.11.2.14.11.15.2.60.1.7.1.1.4	Integer32	read-write	The value of rate-limit that configured for diffrent service class. The unit is permillage.
hpnicfRprMacAddrLearn	1.3.6.1.4.1.11.2.14.11.15.2.60.1.8
hpnicfRprMacLearnCfgTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1		not-accessible	The RPR MAC Address Table.
hpnicfRprMacLearnCfgEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1		not-accessible	The entry of RPR MAC Address Table.
NUM hpnicfRprMacLearnIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.1	InterfaceIndex	not-accessible	The ifIndex of RPR interface.
MAC hpnicfRprMacLearnRprMac	1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.2	MacAddress	not-accessible	The MAC address of the RPR station.
INT hpnicfRprMacLearnType	1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.3	INTEGER	read-create	The type of MAC address item that the user built. The type includes static and dynamic.
MAC hpnicfRprMacLearnDestMac	1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.4	MacAddress	read-create	The destination of MAC address.
I32 hpnicfRprMacLearnVlanId	1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.5	Integer32	read-create	The vlan ID that the MAC address learned from by RPR staion.
HPN hpnicfRprMacLearnRinglet	1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.6	HpnicfRprRingletID	read-create	The identifier of the ring which frames are sent from the source station to the destination station.
INT hpnicfRprMacLearnTtl	1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.7	INTEGER	read-only	The hops from source station to destination station on the selected ringlet.
T/F hpnicfRprMacLearnIsValid	1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.8	TruthValue	read-only	The flag identify whether the configured mac address is valid. If it is true, the configured mac address is valid, otherwise it's invalid.
ROW hpnicfRprMacLearnRowStatus	1.3.6.1.4.1.11.2.14.11.15.2.60.1.8.1.1.9	RowStatus	read-create	The status of this table entry. The status includes createAndGo, active and destroy.
hpnicfRprTrapVar	1.3.6.1.4.1.11.2.14.11.15.2.60.1.9
hpnicfRprTrapVarTable	1.3.6.1.4.1.11.2.14.11.15.2.60.1.9.1		not-accessible	The RPR Defect Report Table that contains varible that used to bind in trap.
hpnicfRprTrapVarEntry	1.3.6.1.4.1.11.2.14.11.15.2.60.1.9.1.1		not-accessible	An entry in the RPR Trap Var Table.
NUM hpnicfRprTrapIfIndex	1.3.6.1.4.1.11.2.14.11.15.2.60.1.9.1.1.1	InterfaceIndex	accessible-for-notify	The ifIndex of RPR interface. It is only used for trap to bind.
HPN hpnicfRprTrapRinglet	1.3.6.1.4.1.11.2.14.11.15.2.60.1.9.1.1.2	HpnicfRprRingletID	accessible-for-notify	The span of RPR station. It is only used for trap to bind.
MAC hpnicfRprTrapTopoMacAddress	1.3.6.1.4.1.11.2.14.11.15.2.60.1.9.1.1.3	MacAddress	accessible-for-notify	The MAC address of RPR station. It is only used for trap to bind.
IP hpnicfRprTrapIpAddress	1.3.6.1.4.1.11.2.14.11.15.2.60.1.9.1.1.4	InetAddress	accessible-for-notify	The IP address of RPR station. It is only used for trap to bind.
hpnicfRprTrap	1.3.6.1.4.1.11.2.14.11.15.2.60.1.10
NTF hpnicfRprTopologyOpenRing	1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.1			The topology openRing trap indicates that the RPR ring is opened.
NTF hpnicfRprTopologyCloseRing	1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.2			The topology openRing trap indicates that the RPR ring is closed.
NTF hpnicfRprTopologyInconsistent	1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.3			The topology inconsistent trap indicates that the topology of RPR is inconsistent.
NTF hpnicfRprTopologyInstability	1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.4			The topology instability trap indicates that the topology of RPR is instability.
NTF hpnicfRprDuplicateMacAddress	1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.5			The duplicate MAC address trap indicates that the mac address of the station on the ring is dulplicate. That means there is the same MAC address between two stations on the ring.
NTF hpnicfRprDulplicateIPAddress	1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.6			The dulplicate IP address trap indicates that the IP address of the station on the ring is dulplicate. That means there is the same IP address between two stations on the ring.
NTF hpnicfRprIncompleteLRTT	1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.7			The incomplete LRTT trap indicates that LRTT is not completed.
NTF hpnicfRprProtecConfigInconsistent	1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.8			The protection configuration inconsistent trap indicates that the configuration of protection mode on the ring is inconsistent. That is one station is configured steer mode while the other is configured wrap mode.
NTF hpnicfRprJumboConfigInconsistent	1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.9			The jumbo configuration inconsistent trap indicates that the configuration of jumbo mode on the ring is inconsistent. That is one station supports jumbo frame while the other doesn't support jumbo frame.
NTF hpnicfRprExceedMaxReservRate	1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.10			The exceeded max reserved rate trap indicates that the rate on the ringlet exceeded the max reserved rate. The operator can configure reserved rate for every station, but the sum of all stations' reserved rate of each RPR ringlet can't exceed maximum.
NTF hpnicfRprExceedMaxStationNum	1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.11			The exceeded max station number trap indicates that the number of the stations on the ring exceeded the max station number.
NTF hpnicfRprMiscabling	1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.12			The miscabling trap indicates that the miscabling event occurred.
NTF hpnicfRprBackPressure	1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.13			The back pressure trap indicates that the backpressure is generated on the ringlet. That is the data flow on the ringlet exceeded the range of rate-limit configured.
NTF hpnicfRprBackPressureOver	1.3.6.1.4.1.11.2.14.11.15.2.60.1.10.14			The back pressure over trap indicates that the backpressure is disappeared on the ringlet.

RFC description

HP ICF Resilient Packet Ring interface operational parameters and alarm management.

Start monitoring HP/Comware router/switch with RPR (Resilient Packet Ring) interfaces with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download HPN-ICF-RPR-MIB