DKSF-70-6-X-X-1

All MIBs › DKSF-70-6-X-X-1

Organization: Alentis Electronics

Last Updated: 2016-08-24

Category: Domain: Environmental Monitoring, Vendor: NetPing/DKSF

Description: MIB for DKSF-70 NetPing device firmware 6.x providing expanded sensor, relay, and environmental monitoring features.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is DKSF-70-6-X-X-1?

DKSF-70-6-X-X-1 is the MIB for the NetPing DKSF-70 device family running firmware 6.x, a remote sensing and control unit used for environmental and equipment monitoring over the network (branded under the "lightcom" enterprise tree). It exposes relay control objects (state, mode, memo, reset behavior) for controlling connected switches/power outlets, thermal sensor objects for reading temperature values from attached probes, and trap configuration for email alerting. Its monitoring focus is squarely on physical/environmental hardware status: reading temperature from npThermoTable sensors and relay on/off state from npRelayTable lets an operator watch equipment-room conditions and remotely toggle power to connected devices, functioning much like an environmental monitoring/PDU controller appliance. It is a self-contained proprietary NetPing MIB with no strong dependency on other standard MIBs evident in the object set. It is typically deployed in server rooms, telecom cabinets, or remote sites where temperature and relay-controlled equipment (fans, heaters, power resets) need remote SNMP monitoring and control. Engineers can download the DKSF-70-6-X-X-1 file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in DKSF-70-6-X-X-1. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

NetPing DKSF-70 environmental sensing/relay controller

Monitoring Examples

An administrator would poll npThermoTable/npThermoEntry, indexed by npThermoSensorN, to read npThermoValue for each attached temperature probe and alert if a room or rack temperature exceeds a safe threshold. Checking npRelayTable/npRelayEntry (indexed by npRelayN) for npRelayState and npRelayMode reveals whether a connected relay-controlled device (like a fan or backup heater) is currently on or off, and npRelayStartReset can be used to trigger a remote power-cycle of attached equipment. Configuring npTrapEmailTo ensures that when npTrapInfo notifications fire (e.g., an over-temperature event), an email alert is sent to the on-call administrator.

What Can Be Monitored

temperature sensor readings
relay on/off state
relay mode configuration
relay reset/power-cycle control
trap email notification configuration

Imported Objects

From SNMPv2-MIB

snmpTraps

OBJECT-IDENTITY

From SNMPv2-SMI

Counter32
Counter64
Gauge32
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
enterprises

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using npIoPulseCounter OID:

Select a NetPing DKSF-70 environmental sensing/relay controller as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type npIoPulseCounter into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. It reports the pulse Counter on IO input line (counts positive fronts) Write 0 to reset. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
lightcom	1.3.6.1.4.1.25728
npCurLoop	1.3.6.1.4.1.25728.8300
npCurLoopEntry	1.3.6.1.4.1.25728.8300.1.1		not-accessible	Current loop sensors Table Row
INT npCurLoopI	1.3.6.1.4.1.25728.8300.1.1.3	INTEGER	read-only	Loop current, mA
INT npCurLoopN	1.3.6.1.4.1.25728.8300.1.1.1	INTEGER	read-only	Index of current loop, 1 to max supported
INT npCurLoopPower	1.3.6.1.4.1.25728.8300.1.1.7	INTEGER	read-write	Control of loop power 0=Off, 1=On, 2=reset by off/on power
INT npCurLoopR	1.3.6.1.4.1.25728.8300.1.1.5	INTEGER	read-only	Resistance of the loop, Ohm
INT npCurLoopStatus	1.3.6.1.4.1.25728.8300.1.1.2	INTEGER	read-only	Status of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Powered
npCurLoopTable	1.3.6.1.4.1.25728.8300.1		not-accessible	Current loop sensors Table
NTF npCurLoopTrap	1.3.6.1.4.1.25728.8300.2.0.1			Status of current loop N has changed!
INT npCurLoopTrapI	1.3.6.1.4.1.25728.8300.2.3	INTEGER	read-only	Loop current, mA
INT npCurLoopTrapN	1.3.6.1.4.1.25728.8300.2.1	INTEGER	read-only	Index of current loop, which status has changed
INT npCurLoopTrapPower	1.3.6.1.4.1.25728.8300.2.7	INTEGER	read-write	Status of loop power 0=Off, 1=On
npCurLoopTrapPrefix	1.3.6.1.4.1.25728.8300.2.0
INT npCurLoopTrapR	1.3.6.1.4.1.25728.8300.2.5	INTEGER	read-only	Resistance of the loop, Ohm
npCurLoopTraps	1.3.6.1.4.1.25728.8300.2
INT npCurLoopTrapStatus	1.3.6.1.4.1.25728.8300.2.2	INTEGER	read-only	Status of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Powered
INT npCurLoopTrapV	1.3.6.1.4.1.25728.8300.2.4	INTEGER	read-only	Voltage drop on the loop, mV
INT npCurLoopV	1.3.6.1.4.1.25728.8300.1.1.4	INTEGER	read-only	Voltage drop on the loop, mV
INT npForcedReboot	1.3.6.1.4.1.25728.911.3	INTEGER	read-write	Write 1 to immediate forced reboot
npGsm	1.3.6.1.4.1.25728.3800
INT npGsmFailed	1.3.6.1.4.1.25728.3800.1.1	INTEGER	read-only	Firmware's GSM module status
npGsmInfo	1.3.6.1.4.1.25728.3800.1
INT npGsmRegistration	1.3.6.1.4.1.25728.3800.1.2	INTEGER	read-only	Status of modem registration in GSM network (AT+CREG? result)
STR npGsmSendSmsUtf8	1.3.6.1.4.1.25728.3800.1.9	DisplayString	read-write	Send arbitrary SMS. Format: [phone_number,phone_number,...] Message One to four destination phone numbers If [] and numbers omitted, mesagge will be sent to preset numbers from SMS setup Cyrillic characters must be in UTF8 encoding.
STR npGsmSendSmsWin1251	1.3.6.1.4.1.25728.3800.1.10	DisplayString	read-write	Send arbitrary SMS. Format: [phone_number,phone_number,...] Message One to four destination phone numbers If [] and numbers omitted, mesagge will be sent to preset numbers from SMS setup Cyrillic characters must be in Win1251 encoding.
INT npGsmStrength	1.3.6.1.4.1.25728.3800.1.3	INTEGER	read-only	GSM signal strength. 0..31 = 0..100%, 99 = unknown or n/a, 255 = updating info
NTF npGsmTrap	1.3.6.1.4.1.25728.3800.2.0.1			GSM modem or SMS firmware problems
npGsmTrapPrefix	1.3.6.1.4.1.25728.3800.2.0
npGsmTraps	1.3.6.1.4.1.25728.3800.2
npIo	1.3.6.1.4.1.25728.8900
npIoEntry	1.3.6.1.4.1.25728.8900.1.1		not-accessible	Digital Input/output Table Row
INT npIoLevelIn	1.3.6.1.4.1.25728.8900.1.1.2	INTEGER	read-only	Input level, 0 or 1
INT npIoLevelOut	1.3.6.1.4.1.25728.8900.1.1.3	INTEGER	read-write	Output level, 0 or 1. Write -1 to flip output.
INT npIoLineN	1.3.6.1.4.1.25728.8900.1.1.1	INTEGER	read-only	Number of IO line, from 1 to max supported
STR npIoMemo	1.3.6.1.4.1.25728.8900.1.1.6	DisplayString	read-only	IO line memo
C32 npIoPulseCounterEx	1.3.6.1.4.1.25728.8900.1.1.9	Counter32	read-write	Pulse Counter on IO input line (counts positive fronts) Write 0 to reset.
INT npIoSinglePulseDuration	1.3.6.1.4.1.25728.8900.1.1.12	INTEGER	read-write	Set duration of single pulse on IO output line, 100ms to 25500ms, min. step is 100ms
INT npIoSinglePulseStart	1.3.6.1.4.1.25728.8900.1.1.13	INTEGER	read-write	Write 1 to start single pulse on IO output. Output will be inverted for time, specified by npIoSinglePulseDuration
npIoTable	1.3.6.1.4.1.25728.8900.1		not-accessible	Digital Input/output Table
NTF npIoTrap	1.3.6.1.4.1.25728.8900.2.0.1			Input state of IO line is changed
INT npIoTrapLevelIn	1.3.6.1.4.1.25728.8900.2.2	INTEGER	read-only	Trap data, new Input level, 0 or 1
STR npIoTrapLevelLegend	1.3.6.1.4.1.25728.8900.2.7	DisplayString	read-only	Legend for current logic level on the IO line
INT npIoTrapLineN	1.3.6.1.4.1.25728.8900.2.1	INTEGER	read-only	Trap data, Number of IO line
STR npIoTrapMemo	1.3.6.1.4.1.25728.8900.2.6	DisplayString	read-only	Trap data, IO line memo
npIoTrapPrefix	1.3.6.1.4.1.25728.8900.2.0
npIoTraps	1.3.6.1.4.1.25728.8900.2
npIr	1.3.6.1.4.1.25728.7900
npIrCtrl	1.3.6.1.4.1.25728.7900.1
INT npIrPlayCmd	1.3.6.1.4.1.25728.7900.1.1	INTEGER	read-write	Write IR command number to send IR command
INT npIrReset	1.3.6.1.4.1.25728.7900.1.2	INTEGER	read-write	Write 1 to reset IR transiever. After reset, send IR command and check npIrStatus.
INT npIrStatus	1.3.6.1.4.1.25728.7900.1.3	INTEGER	read-only	IR transiever status
npReboot	1.3.6.1.4.1.25728.911
npRelay	1.3.6.1.4.1.25728.5500
npRelayEntry	1.3.6.1.4.1.25728.5500.5.1		not-accessible	Relay/outlet table row
STR npRelayMemo	1.3.6.1.4.1.25728.5500.5.1.6	DisplayString	read-only	Relay memo
INT npRelayMode	1.3.6.1.4.1.25728.5500.5.1.2	INTEGER	read-write	Control of relay: -1 - flip between on(1) and off(0) 0 - manual off 1 - manual on 2 - watchdog 3 - schedule 4 - both schedule and watchdog (while switched on by schedule) 5 - logic
INT npRelayN	1.3.6.1.4.1.25728.5500.5.1.1	INTEGER	read-only	The N of output relay
INT npRelayStartReset	1.3.6.1.4.1.25728.5500.5.1.3	INTEGER	read-write	Write 1 to start reset (switch relay off for some time)
INT npRelayState	1.3.6.1.4.1.25728.5500.5.1.15	INTEGER	read-only	Actual relay state at the moment, regardless of source of control. 0 - relay is off 1 - relay is on
npRelayTable	1.3.6.1.4.1.25728.5500.5		not-accessible	Watchdog and outlet/relay control table
npRelHumEntry	1.3.6.1.4.1.25728.8400.1.1		not-accessible	Humidity+Temperature Sensors Table Row
npRelHumidity	1.3.6.1.4.1.25728.8400
STR npRelHumMemo	1.3.6.1.4.1.25728.8400.1.1.6	DisplayString	read-only	Sensor Memo/Location
INT npRelHumN	1.3.6.1.4.1.25728.8400.1.1.1	INTEGER	read-only	Index of Humidity+Temperature sensor, 1 to max supported
INT npRelHumSafeRangeHigh	1.3.6.1.4.1.25728.8400.1.1.7	INTEGER	read-only	Relative Humidity safe range, top margin, %RH
INT npRelHumSafeRangeLow	1.3.6.1.4.1.25728.8400.1.1.8	INTEGER	read-only	Relative Humidity safe range, bottom margin, %RH
INT npRelHumStatus	1.3.6.1.4.1.25728.8400.1.1.3	INTEGER	read-only	Status of Relative Humiduty
npRelHumTable	1.3.6.1.4.1.25728.8400.1		not-accessible	Humidity+Temperature Sensors Table
INT npRelHumTempSafeRangeHigh	1.3.6.1.4.1.25728.8400.1.1.9	INTEGER	read-only	Temperature safe range, top margin, deg.C
INT npRelHumTempSafeRangeLow	1.3.6.1.4.1.25728.8400.1.1.10	INTEGER	read-only	Temperature safe range, bottom margin, deg.C
INT npRelHumTempStatus	1.3.6.1.4.1.25728.8400.1.1.5	INTEGER	read-only	Status of Relative Humiduty
INT npRelHumTempValue	1.3.6.1.4.1.25728.8400.1.1.4	INTEGER	read-only	Sensor temperature, deg.C
npRelHumTrap	1.3.6.1.4.1.25728.8400.6
NTF npRelHumTrapAboveSafe	1.3.6.1.4.1.25728.8400.6.103			Humidity above the Safe range
NTF npRelHumTrapAllChannels	1.3.6.1.4.1.25728.8400.6.127.99			Status of Humidity has changed!
npRelHumTrapAllEvents	1.3.6.1.4.1.25728.8400.6.127
NTF npRelHumTrapBelowSafe	1.3.6.1.4.1.25728.8400.6.101			Humidity below the Safe range
npRelHumTrapData	1.3.6.1.4.1.25728.8400.3
STR npRelHumTrapDataMemo	1.3.6.1.4.1.25728.8400.3.6	DisplayString	read-only	Sensor Memo/Location
INT npRelHumTrapDataN	1.3.6.1.4.1.25728.8400.3.1	INTEGER	read-only	Index of Humidity+Temperature sensor, 1 to max supported
INT npRelHumTrapDataSafeRangeHigh	1.3.6.1.4.1.25728.8400.3.7	INTEGER	read-only	Relative Humidity safe range, top margin, %RH or deg.C
INT npRelHumTrapDataSafeRangeLow	1.3.6.1.4.1.25728.8400.3.8	INTEGER	read-only	Relative Humidity safe range, bottom margin, %RH or deg.C
INT npRelHumTrapDataStatus	1.3.6.1.4.1.25728.8400.3.4	INTEGER	read-only	Status of humidity or temperature
INT npRelHumTrapDataValue	1.3.6.1.4.1.25728.8400.3.2	INTEGER	read-only	Sensor humidity, %RH, or temperature, deg.C
NTF npRelHumTrapFail	1.3.6.1.4.1.25728.8400.6.100			Rel.Humidity sensor failed!
NTF npRelHumTrapSafe	1.3.6.1.4.1.25728.8400.6.102			Humidity in the Safe range
npRelHumTrapTemp	1.3.6.1.4.1.25728.8400.7
NTF npRelHumTrapTempAboveSafe	1.3.6.1.4.1.25728.8400.7.103			Temperature above the Safe range
NTF npRelHumTrapTempAllChannels	1.3.6.1.4.1.25728.8400.7.127.99			Status of Temperature has changed!
npRelHumTrapTempAllEvents	1.3.6.1.4.1.25728.8400.7.127
NTF npRelHumTrapTempBelowSafe	1.3.6.1.4.1.25728.8400.7.101			Temperature below the Safe range
NTF npRelHumTrapTempFail	1.3.6.1.4.1.25728.8400.7.100			Sensor failed!
NTF npRelHumTrapTempSafe	1.3.6.1.4.1.25728.8400.7.102			Temperature in the Safe range
INT npRelHumValue	1.3.6.1.4.1.25728.8400.1.1.2	INTEGER	read-only	Relative humidity value, %
INT npResetStack	1.3.6.1.4.1.25728.911.2	INTEGER	read-write	Write 1 to re-initialize network stack
npSmoke	1.3.6.1.4.1.25728.8200
npSmokeEntry	1.3.6.1.4.1.25728.8200.1.1		not-accessible	Smoke Sensors Table Row
STR npSmokeMemo	1.3.6.1.4.1.25728.8200.1.1.6	DisplayString	read-only	Smoke sensor memo
INT npSmokePower	1.3.6.1.4.1.25728.8200.1.1.3	INTEGER	read-write	Controls power on Smoke sensor current loop
INT npSmokeReset	1.3.6.1.4.1.25728.8200.1.1.4	INTEGER	read-write	Write 1 to switch off for approx. 10s to reset sensor
INT npSmokeSensorN	1.3.6.1.4.1.25728.8200.1.1.1	INTEGER	read-only	The id of 1Wire Smoke sensor, 1 to 4
INT npSmokeStatus	1.3.6.1.4.1.25728.8200.1.1.2	INTEGER	read-only	Status of Smoke sensor
npSmokeTable	1.3.6.1.4.1.25728.8200.1		not-accessible	Smoke Sensors Table
NTF npSmokeTrap	1.3.6.1.4.1.25728.8200.2.0.1			Status of 1W Smoke sensor has changed
STR npSmokeTrapMemo	1.3.6.1.4.1.25728.8200.2.6	DisplayString	read-only	Smoke sensor memo
npSmokeTrapPrefix	1.3.6.1.4.1.25728.8200.2.0
npSmokeTraps	1.3.6.1.4.1.25728.8200.2
INT npSmokeTrapSensorN	1.3.6.1.4.1.25728.8200.2.1	INTEGER	read-only	The id of 1Wire Smoke sensor, 1 to 4
INT npSmokeTrapStatus	1.3.6.1.4.1.25728.8200.2.2	INTEGER	read-only	New status of Smoke sensor
INT npSoftReboot	1.3.6.1.4.1.25728.911.1	INTEGER	read-write	Write 1 to reboot device after current operations completition
npThermo	1.3.6.1.4.1.25728.8800
npThermoEntry	1.3.6.1.4.1.25728.8800.1.1		not-accessible	Thermo Sensors Table Row
INT npThermoHigh	1.3.6.1.4.1.25728.8800.1.1.5	INTEGER	read-only	Top margin of normal temperature range, deg.C
INT npThermoLow	1.3.6.1.4.1.25728.8800.1.1.4	INTEGER	read-only	Bottom margin of normal temperature range, deg.C
STR npThermoMemo	1.3.6.1.4.1.25728.8800.1.1.6	DisplayString	read-only	T channel memo
INT npThermoSensorN	1.3.6.1.4.1.25728.8800.1.1.1	INTEGER	read-only	The id of temperature sensor, 1 to 8
INT npThermoStatus	1.3.6.1.4.1.25728.8800.1.1.3	INTEGER	read-only	Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat)
npThermoTable	1.3.6.1.4.1.25728.8800.1		not-accessible	Thermo Sensors Table
NTF npThermoTrap	1.3.6.1.4.1.25728.8800.2.0.1			Status of Thermo sensor is changed (crossing of normal temp. range)
INT npThermoTrapHigh	1.3.6.1.4.1.25728.8800.2.5	INTEGER	read-only	Top margin of normal temperature range, deg.C
INT npThermoTrapLow	1.3.6.1.4.1.25728.8800.2.4	INTEGER	read-only	Bottom margin of normal temperature range, deg.C
STR npThermoTrapMemo	1.3.6.1.4.1.25728.8800.2.6	DisplayString	read-only	T channel memo
npThermoTrapPrefix	1.3.6.1.4.1.25728.8800.2.0
npThermoTraps	1.3.6.1.4.1.25728.8800.2
INT npThermoTrapSensorN	1.3.6.1.4.1.25728.8800.2.1	INTEGER	read-only	The id of temperature sensor, 1 to 8
INT npThermoTrapStatus	1.3.6.1.4.1.25728.8800.2.3	INTEGER	read-only	Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat)
INT npThermoTrapValue	1.3.6.1.4.1.25728.8800.2.2	INTEGER	read-only	Temperature, deg.C
INT npThermoValue	1.3.6.1.4.1.25728.8800.1.1.2	INTEGER	read-only	Temperature, deg.C
NUM npThermoValuePrecise	1.3.6.1.4.1.25728.8800.1.1.7	FixedPoint1000	read-only	Temperature, deg.C, with fractional part 3 digits after point
STR npTrapEmailTo	1.3.6.1.4.1.25728.90.1	DisplayString	read-only	user-specified e-mail for NetPing Trap Forwarding Service
npTrapInfo	1.3.6.1.4.1.25728.90
uniPingServerSolutionV3	1.3.6.1.4.1.25728.70			Generic MIB for NetPing remote sensing and control

RFC description

Generic NetPing remote sensing and control MIB for temperature, relays, IO lines, and GSM functions.

Start monitoring NetPing DKSF-70 environmental sensing/relay controller with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download DKSF-70-6-X-X-1