CISCO-ATM-CONN-MIB

All MIBs › CISCO-ATM-CONN-MIB

Organization: Cisco Systems, Inc.

Last Updated: 2002-07-12

Category: ATM

Description: Manages ATM virtual circuit connections (PVCs/SVCs) on Cisco ATM platforms.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is CISCO-ATM-CONN-MIB?

CISCO-ATM-CONN-MIB is a Cisco extension to the standard ATM connection tables defined in RFC 1695, adding vendor-specific management for ATM virtual path/virtual channel (VPL/VCL) connections on Cisco ATM switching platforms. It exposes per-connection configuration and status such as cast type, span type, connection state, UPC/policing mode, and OAM loopback and AIS/RDI (alarm indication/remote defect indication) settings. Its monitoring purpose is connection- and fault-status tracking on ATM switches: an operator checks ciscoAtmVplConnState to confirm a virtual path is up, and monitors OAM AIS/RDI flags to detect upstream/downstream ATM fault conditions propagating through the network. It directly extends and depends on the standard ATM-MIB (RFC 1695) VPL/VCL tables rather than replacing them. It is used in legacy carrier and enterprise ATM switching deployments, increasingly rare today but still found in older telecom/WAN infrastructure running ATM PVCs/SVCs. Engineers can download the CISCO-ATM-CONN-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in CISCO-ATM-CONN-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Cisco ATM switches

Monitoring Examples

An admin polls ciscoAtmVplTable/Entry to check ciscoAtmVplConnState and ciscoAtmVplOamAisEnable/ciscoAtmVplOamRdiEnable for a given virtual path. A connection state that isn't "operational" alongside an active AIS condition would indicate an ATM fault upstream of the switch, such as a failed transmission facility, propagating an alarm indication signal down the path.

What Can Be Monitored

ATM virtual path connection state
cast type/span type configuration
UPC/policing mode
OAM loopback settings
AIS/RDI alarm indication status

Imported Objects

From ATM-MIB

AtmTrafficDescrParamIndex
atmVclVci	OBJECT-TYPE
atmVclVpi	OBJECT-TYPE
atmVplVpi	OBJECT-TYPE

From CISCO-ATM-IF-MIB

NsapAtmAddr

From CISCO-ATM-RM-MIB

LsPerVcqThresholdGroup

From CISCO-SMI

ciscoExperiment

OBJECT-IDENTITY

From IF-MIB

InterfaceIndexOrZero
ifIndex	OBJECT-TYPE

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Counter32
Gauge32
Integer32
MODULE-IDENTITY
OBJECT-TYPE

From SNMPv2-TC

RowStatus
TEXTUAL-CONVENTION
TimeStamp
TruthValue

How to Use in IPNetwork Monitor

Example using ciscoAtmVplInClp0Cells OID:

Select a Cisco ATM switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type ciscoAtmVplInClp0Cells into the Find box to locate it in the OID tree, then select it and click OK. The total number of cells with the CLP bit clear received on this VPL. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter32-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
ciscoAtmConnMIB	1.3.6.1.4.1.9.10.13			This MIB module is a cisco extension to VPL/VCL table defined in rfc1695 for ATM switch connection management.
ciscoAtmConnMIBCompliance	1.3.6.1.4.1.9.10.13.3.1.1			The compliance statement for the Cisco ATM connection management group.
ciscoAtmConnMIBCompliance2	1.3.6.1.4.1.9.10.13.3.1.2			The compliance statement for the Cisco ATM connection management group.
ciscoAtmConnMIBCompliance3	1.3.6.1.4.1.9.10.13.3.1.3			The compliance statement for the Cisco ATM connection management group.
ciscoAtmConnMIBCompliance4	1.3.6.1.4.1.9.10.13.3.1.4			The compliance statement for the Cisco ATM connection management group.
ciscoAtmConnMIBCompliance5	1.3.6.1.4.1.9.10.13.3.1.5			The compliance statement for the Cisco ATM connection management group.
ciscoAtmConnMIBCompliance6	1.3.6.1.4.1.9.10.13.3.1.6			The compliance statement for the Cisco ATM connection management group.
ciscoAtmConnMIBCompliance7	1.3.6.1.4.1.9.10.13.3.1.7			The compliance statement for the Cisco ATM connection management group.
ciscoAtmConnMIBCompliance8	1.3.6.1.4.1.9.10.13.3.1.8			The compliance statement for the Cisco ATM connection management group.
ciscoAtmConnMIBCompliances	1.3.6.1.4.1.9.10.13.3.1
ciscoAtmConnMIBConformance	1.3.6.1.4.1.9.10.13.3
ciscoAtmConnMIBGroup	1.3.6.1.4.1.9.10.13.3.2.1
ciscoAtmConnMIBGroup1	1.3.6.1.4.1.9.10.13.3.2.9
ciscoAtmConnMIBGroup2	1.3.6.1.4.1.9.10.13.3.2.2
ciscoAtmConnMIBGroup3	1.3.6.1.4.1.9.10.13.3.2.3
ciscoAtmConnMIBGroup4	1.3.6.1.4.1.9.10.13.3.2.10
ciscoAtmConnMIBGroups	1.3.6.1.4.1.9.10.13.3.2
ciscoAtmConnMIBlsFcPfqGroup	1.3.6.1.4.1.9.10.13.3.2.5			A collection of objects which are supported on LS1010 systems equipped with the FC-PFQ feature card.
ciscoAtmConnMIBlsFcPfqGroup1	1.3.6.1.4.1.9.10.13.3.2.8			A collection of objects which are supported on LS1010 systems equipped with the FC-PFQ feature card.
ciscoAtmConnMIBlsPerVcqGroup	1.3.6.1.4.1.9.10.13.3.2.4			A collection of objects which are supported on platforms using the Lightstream per-VC queueing chipset.
ciscoAtmConnMIBlsPerVcqGroup2	1.3.6.1.4.1.9.10.13.3.2.6			A collection of objects which are supported on platforms using the Lightstream per-VC queueing chipset.
ciscoAtmConnMIBNegTraffGroup	1.3.6.1.4.1.9.10.13.3.2.7			A collection of objects to report negotiated traffic parameters on a Cisco ATM switch.
ciscoAtmConnMIBObjects	1.3.6.1.4.1.9.10.13.1
ciscoAtmConnNmsGroup	1.3.6.1.4.1.9.10.13.3.2.11			A group of objects that provides additional information for a management system
ciscoAtmSnoopVc	1.3.6.1.4.1.9.10.13.1.5
SNO ciscoAtmSnoopVcDir	1.3.6.1.4.1.9.10.13.1.5.1.1.4	SnoopDirType	read-create	This specifies the traffic direction at the snooped connection endpoint.
ciscoAtmSnoopVcEntry	1.3.6.1.4.1.9.10.13.1.5.1.1		not-accessible	An entry in the Snoop VC table. This entry models a VC snooping connection. The ifIndex indicates the snooping interface, the atmVclVpi and atmVclVci specifies the VPI and VCI value of the snooping connection. To create or destroy a snooping connection at an ATM interface, the following procedures are used: Configure VC Snooping A snooping connection is configured in one step by a set-request with all necessary snoop parameter values and set-request to the object ciscoAtmSnoopVcRowStatus to createAndGo(4). This may fail for the following reasons: - The selected snooping VPI/VCI values are unavailable, - The selected snooping VPI/VCI values are in use. - The selected snooping interface is CPU interface. - The selected snooped connection doesn't exist. - There is no traffic in the selected snoop direction. - Resource failure during configuration of snooping connection. De-Configure VC Snooping A snooping connection is deconfigured by a set-request to the object ciscoAtmSnoopVcRowStatus to destroy(6), and the agent releases all associated resources.
ROW ciscoAtmSnoopVcRowStatus	1.3.6.1.4.1.9.10.13.1.5.1.1.6	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table. This gives the way to configure one-shot per-vc snooping connection
NUM ciscoAtmSnoopVcSnoopedIfIndex	1.3.6.1.4.1.9.10.13.1.5.1.1.1	InterfaceIndexOrZero	read-create	This specifies the ifIndex of the snooped interface.
I32 ciscoAtmSnoopVcSnoopedVci	1.3.6.1.4.1.9.10.13.1.5.1.1.3	Integer32	read-create	This specifies the VCI value of the snooped connection endpoint.
I32 ciscoAtmSnoopVcSnoopedVpi	1.3.6.1.4.1.9.10.13.1.5.1.1.2	Integer32	read-create	This specifies the VPI value of the snooped connection endpoint.
CON ciscoAtmSnoopVcState	1.3.6.1.4.1.9.10.13.1.5.1.1.5	ConnState	read-only	The connection state of this Snooping connetion.
ciscoAtmSnoopVcTable	1.3.6.1.4.1.9.10.13.1.5.1		not-accessible	Snooping VC Table.
ciscoAtmSnoopVp	1.3.6.1.4.1.9.10.13.1.6
SNO ciscoAtmSnoopVpDir	1.3.6.1.4.1.9.10.13.1.6.1.1.3	SnoopDirType	read-create	This specifies the traffic direction at the snooped connection endpoint.
ciscoAtmSnoopVpEntry	1.3.6.1.4.1.9.10.13.1.6.1.1		not-accessible	An entry in the Snoop VP table. This entry models a VP snooping connection. The ifIndex indicates the snooping interface, the atmVclVpi specifies the VPI value of the snooping connection. To create or destroy a snooping connection at an ATM interface, the following procedures are used: Configure VP Snooping A snooping connection is configured in one step by a set-request with all necessary snoop parameter values and set-request to the object ciscoAtmSnoopVpRowStatus to createAndGo(4). This may fail for the following reasons: - The selected snooping VPI values are unavailable, - The selected snooping VPI values are in use. - The selected snooping interface is CPU interface. - The selected snooped connection doesn't exist. - There is no traffic in the selected snoop direction. - Resource failure during configuration of snooping connection. De-Configure VP Snooping A snooping connection is deconfigured by a set-request to the object ciscoAtmSnoopVpRowStatus to destroy(6), and the agent releases all associated resources.
ROW ciscoAtmSnoopVpRowStatus	1.3.6.1.4.1.9.10.13.1.6.1.1.5	RowStatus	read-create	This object is used to create a new row or delete an existing row in this table. This gives the way to configure one-shot per-vp snooping connection
NUM ciscoAtmSnoopVpSnoopedIfIndex	1.3.6.1.4.1.9.10.13.1.6.1.1.1	InterfaceIndexOrZero	read-create	This specifies the ifIndex of the snooped interface.
I32 ciscoAtmSnoopVpSnoopedVpi	1.3.6.1.4.1.9.10.13.1.6.1.1.2	Integer32	read-create	This specifies the VPI value of the snooped connection endpoint.
CON ciscoAtmSnoopVpState	1.3.6.1.4.1.9.10.13.1.6.1.1.4	ConnState	read-only	The connection state of this Snooping connection .
ciscoAtmSnoopVpTable	1.3.6.1.4.1.9.10.13.1.6.1		not-accessible	Snooping VP Table.
ciscoAtmSvc	1.3.6.1.4.1.9.10.13.1.4
OCT ciscoAtmSvcAddr	1.3.6.1.4.1.9.10.13.1.4.1.1.1	OCTET STRING	not-accessible	It depends on the direction.This could be p2pCallingSide address on a called side VCL, or p2pCalledSide address on a calling side VCL or p2mpRoot address on a p2mp leaf side VCL or p2mpLeaf address on a p2mp root side VCL.
ciscoAtmSvcAddrEntry	1.3.6.1.4.1.9.10.13.1.4.1.1		not-accessible	An entry in the SVC address table.
ciscoAtmSvcAddrTable	1.3.6.1.4.1.9.10.13.1.4.1		not-accessible	Switched virtual channel link address table.
DIR ciscoAtmSvcDirection	1.3.6.1.4.1.9.10.13.1.4.1.1.4	Direction	read-only	Indicate whether this VCL is calling side, called side, root or leaf for this address.
T/F ciscoAtmSvcFrameDiscardUsesAal5Ie	1.3.6.1.4.1.9.10.13.1.4.2	TruthValue	read-write	Determines mechanism to use on interfaces to specify frame discard. Specifying a value of true causes the presence of the AAL5 IE to influence whether frame discard is used on an SVC. If AAL5 IE is present in a received SETUP, frame discard is used. Specifying a value of false results in no influence on presence of the frame discard by the AAL5 IE.
I32 ciscoAtmSvcVci	1.3.6.1.4.1.9.10.13.1.4.1.1.3	Integer32	not-accessible	This SVC's VCI value on this interface.
I32 ciscoAtmSvcVpi	1.3.6.1.4.1.9.10.13.1.4.1.1.2	Integer32	not-accessible	This SVC's VPI value on this interface.
ciscoAtmSvp	1.3.6.1.4.1.9.10.13.1.3
OCT ciscoAtmSvpAddr	1.3.6.1.4.1.9.10.13.1.3.1.1.1	OCTET STRING	not-accessible	It depends on the direction.This could be p2pCallingSide address on a called side VPL, or p2pCalledSide address on a calling side VPL or p2mpRoot address on a p2mp leaf side VPL or p2mpLeaf address on a p2mp root side VPL.
ciscoAtmSvpAddrEntry	1.3.6.1.4.1.9.10.13.1.3.1.1		not-accessible	An entry in the Switched Vrtual Path address table.
ciscoAtmSvpAddrTable	1.3.6.1.4.1.9.10.13.1.3.1		not-accessible	Switched virtual path link address table.
DIR ciscoAtmSvpDirection	1.3.6.1.4.1.9.10.13.1.3.1.1.3	Direction	read-only	Indicate whether this VPL is calling side, called side, root or leaf for this address.
INT ciscoAtmSvpVpi	1.3.6.1.4.1.9.10.13.1.3.1.1.2	INTEGER	not-accessible	This SVP's VPI value on this interface.
ciscoAtmVcl	1.3.6.1.4.1.9.10.13.1.2
INT ciscoAtmVclAalEncapFlag	1.3.6.1.4.1.9.10.13.1.2.1.1.21	INTEGER	read-write	Encapsulation type for terminating VC.
INT ciscoAtmVclAalEncapProtocol	1.3.6.1.4.1.9.10.13.1.2.1.1.22	INTEGER	read-write	Protocol for terminating VC if EncapFlag is aal5Mux.
INT ciscoAtmVclAalUserVcType	1.3.6.1.4.1.9.10.13.1.2.1.1.23	INTEGER	read-write	Following is the list of user virtual circuit types in case aal5Lane encapusation on this virtual channel. boxConfigure -- The shared Server/Client end of a Configure VCC busForward -- The BUS end of the Data Forward VCC busSend -- The BUS end of the Data Send VCC clientConfigure -- The LE Client end of the Configure Direct VCC clientData -- One end of the Data Direct VCC clientDirect -- The LE Client end of the Control Direct VCC clientDistribute -- The LE Client end of the Control Distribute VCC clientForward -- The LE Client end of the Multicast Forward VCC clientSend -- The LE Client end of the Multicast Send VCC configure -- The Config Server end of any Configure VCC serverConfigure -- The LE Server end of the Configure VCC serverDirect -- The LE Server end of the Control Direct VCC.
I32 ciscoAtmVclAtmInArpInterval	1.3.6.1.4.1.9.10.13.1.2.1.1.24	Integer32	read-write	Time interval in minutes to send InArp on a PVC for IP over ATM. 0 will disable the InArp for this pvc.
CAS ciscoAtmVclCastType	1.3.6.1.4.1.9.10.13.1.2.1.1.1	CastType	read-write	Vcl type is either a point to point connection or point to multipoint root or leaf.
C32 ciscoAtmVclCellDrops	1.3.6.1.4.1.9.10.13.1.2.1.1.47	Counter32	read-only	The total number of cells received on this VCL, but discarded. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
C32 ciscoAtmVclClp0VcqFullCellDrops	1.3.6.1.4.1.9.10.13.1.2.1.1.48	Counter32	read-only	The total number of cells received on this VCL with the CLP bit clear, discarded because the per-VC queue limit is exceeded. This counter is valid only: - if EPD is disabled on the VCL. - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
C32 ciscoAtmVclClp1Drops	1.3.6.1.4.1.9.10.13.1.2.1.1.37	Counter32	read-only	Never implemented.
CON ciscoAtmVclConfigType	1.3.6.1.4.1.9.10.13.1.2.1.1.3	ConfigType	read-write	Vcl type is either a PVC, SVC, Soft PVC or Soft Passive half leg. The half leg can be set to Passive through user configuration only.
STR ciscoAtmVclConnName	1.3.6.1.4.1.9.10.13.1.2.1.1.55	SnmpAdminString	read-write	A human readable string that identifies this connection. This object will return a zero-length string if value is not set.
CON ciscoAtmVclConnState	1.3.6.1.4.1.9.10.13.1.2.1.1.6	ConnState	read-write	The connection state of this VCL.
INT ciscoAtmVclConnType	1.3.6.1.4.1.9.10.13.1.2.1.1.56	INTEGER	read-write	This object represent the PVC Type for this connection. - local connection within the node - endToEnd across several nodes. This object serves as an information object for a management system and has no functional meaning to the switch.
NUM ciscoAtmVclCrossIfIndex	1.3.6.1.4.1.9.10.13.1.2.1.1.15	InterfaceIndexOrZero	read-write	For point to point, this is the cross-connected VCL's ifIndex of this VCL. For point to multi-point connection, this will be the root VCL's ifIndex for a leaf VCL entry in the multicast chain, or it's the 1st leaf VCL for a root VCL entry. If it's zero, it means it's not cross-connected yet. Atomically set ciscoAtmVclConnState, ciscoAtmVclCrossIfindex, ciscoAtmVclCrossVpi and ciscoAtmVclCrossVci will create or delete a cross connection to crossed half leg of this ciscoAtmVclCrossIfindex, ciscoAtmVclCrossVpi and ciscoAtmVclCrossVci for p2p PVC, or add or drop a multicast connection to/from the root of this ciscoAtmVclCrossIfindex, ciscoAtmVclCrossVpi and ciscoAtmVclCrossVci on the multicast chain for p2mp PVC.
I32 ciscoAtmVclCrossVci	1.3.6.1.4.1.9.10.13.1.2.1.1.17	Integer32	read-write	This specifies the VCI value of the VCL to which this VCL is cross-connected. For point to multi-point connection, this is the root VCL's VCI for the leaf entry. Similarly it is the 1st leaf's VCI value for the root entry.
I32 ciscoAtmVclCrossVpi	1.3.6.1.4.1.9.10.13.1.2.1.1.16	Integer32	read-write	This specifies the VPI value of the VCL to which this VCL is cross-connected. For point to multi-point connection, this is the root VCL's VPI for the leaf entry. Similarly it is the 1st leaf's VPI value for the root entry.
I32 ciscoAtmVclDefaultRxUpcTolerance	1.3.6.1.4.1.9.10.13.1.2.1.1.38	Integer32	read-only	If the tolerance (CDVT for CBR, ABR, UBR connections, Maximum Burst Size for VBR connectons) requested for Usage Parameter Control is not explicitly specified in VCL creation, this object contains the default that is used.If tolerance is explicitly specified in VCL creation, it can be found in the Traffic Table row specified by atmVclReceiveTrafficDescrIndex, and the value of this object is -1.
I32 ciscoAtmVclDefaultRxUpcVbrCdvt	1.3.6.1.4.1.9.10.13.1.2.1.1.39	Integer32	read-only	If the Cell Delay Variation Tolerance (CDVT) requested for Usage Parameter Control for a VBR connection is not explicitly specified in VCL creation, this object contains the default that is used. If CDVT is explicitly specified in VCL creation, it can be found in the Traffic Table row specified by atmVclReceiveTrafficDescrIndex, and the value of this object is -1.
ciscoAtmVclEntry	1.3.6.1.4.1.9.10.13.1.2.1.1		not-accessible	An entry in the Vcl table.This entry is used to model a bi-directional Vcl. This table augments the atmVclTable defined in RFC 1695. However it uses ifIndex, atmVclVpi and atmVclVci as an Index for historical reasons. The entries are created/deleted as a by-product of creating and deleting entries in the atmVclTable.
INT ciscoAtmVclEpdEnable	1.3.6.1.4.1.9.10.13.1.2.1.1.5	INTEGER	read-write	Early Packet Discard option used for this VCL. The use is as follows: enable(1) Packet-discard is enabled. disable(2) Packet-discard is disabled. useTrafficDescr(3) Packet-discard in the receive direction is as specified by the atmTrafficFrameDiscard value in row corresponding to atmVclReceiveTrafficDescrIndex. For VCLs of type spvcInitiator, the packet-discard in the reverse direction is as specified by the atmTrafficFrameDiscard value in row corresponding to atmVclTransmitTrafficDescrIndex.
C32 ciscoAtmVclEpdTpdCellDrops	1.3.6.1.4.1.9.10.13.1.2.1.1.33	Counter32	read-only	Never implemented.
C32 ciscoAtmVclEpdTpdPacketDrops	1.3.6.1.4.1.9.10.13.1.2.1.1.34	Counter32	read-only	The total number of EPD/TPD packet drops of packets received on this VCL. This counter is valid only: - if EPD is enabled on this VCL. - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing.
C32 ciscoAtmVclEpdTpdPacketsIn	1.3.6.1.4.1.9.10.13.1.2.1.1.35	Counter32	read-only	The total number of packets received in their entirety on this VPL. This counter is valid only: - if EPD is enabled on this VCL. - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing.
C32 ciscoAtmVclInCells	1.3.6.1.4.1.9.10.13.1.2.1.1.13	Counter32	read-only	The total number of cells received on this VCL.
C32 ciscoAtmVclInClp0Cells	1.3.6.1.4.1.9.10.13.1.2.1.1.43	Counter32	read-only	The total number of cells with the CLP bit clear received on this VCL. Note that these cells may subsequently be discarded. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
C32 ciscoAtmVclInClp1Cells	1.3.6.1.4.1.9.10.13.1.2.1.1.44	Counter32	read-only	The total number of cells with the CLP bit set received on this VCL. Note that these cells may subsequently be discarded. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
TIM ciscoAtmVclInstallTime	1.3.6.1.4.1.9.10.13.1.2.1.1.12	TimeStamp	read-only	The time stamp derived from sysUpTime when this VCL gets created. The VCL entries are created/deleted as a by-product of creating and deleting entries in the atmVclTable defined in RFC1695.
I32 ciscoAtmVclLastReleaseCause	1.3.6.1.4.1.9.10.13.1.2.1.1.31	Integer32	read-only	Value of the Cause field of the Cause Information Element in the last Release Signalling message received for this SPVC. Indicates the reason for the Release. ciscoAtmVclConfigType is not soft then ciscoAtmVclLastReleaseCause value should be ignored.
LOC ciscoAtmVclLocation	1.3.6.1.4.1.9.10.13.1.2.1.1.28	Location	read-only	Indicate calling or called side of a soft PVC. If ciscoAtmVclConfigType is not soft then ciscoAtmVclLocation value should be ignored.
LSP ciscoAtmVclLsPerVcQThreshGrp	1.3.6.1.4.1.9.10.13.1.2.1.1.42	LsPerVcqThresholdGroup	read-only	The Threshold Group to which the cell-queue for cells received by this VC are queued. Note that this value is not valid until the VCL is in an active cross-connect. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset.
INT ciscoAtmVclLsPerVcqWrrWeight	1.3.6.1.4.1.9.10.13.1.2.1.1.40	INTEGER	read-write	Configure the weighting specified for a VC half-leg within a service class to make the scheduling decision among other active VCLs in the service class. This is for transmit on the VCL on the interface. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset.
G32 ciscoAtmVclLsPerVcqXmtQueuedCells	1.3.6.1.4.1.9.10.13.1.2.1.1.41	Gauge32	read-only	Number of cells received on this VCL and residing on the per-connection queue. Note that this value is not valid until the VCL is in an active cross-connect. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset.
NUM ciscoAtmVclNextLeafIfIndex	1.3.6.1.4.1.9.10.13.1.2.1.1.18	InterfaceIndexOrZero	read-only	For point to point, this is zero i.e. not used. For point to multi-point connection, this will be the next leaf VCL's ifIndex on the multicast chain. This will be 0 if this is the root VCL entry. If it's zero for a leaf VCL, it means this is the last leaf.
I32 ciscoAtmVclNextLeafVci	1.3.6.1.4.1.9.10.13.1.2.1.1.20	Integer32	read-only	For point to point, this is zero i.e. not used. This apply only to point to multi-point connection, this will be the next leaf VCL's VCI on the multicast chain.
I32 ciscoAtmVclNextLeafVpi	1.3.6.1.4.1.9.10.13.1.2.1.1.19	Integer32	read-only	For point to point, this is zero i.e. not used. This apply only to point to multi-point connection, this will be the next leaf VCL's VPI on the multicast chain.
C32 ciscoAtmVclNumAttempts	1.3.6.1.4.1.9.10.13.1.2.1.1.30	Counter32	read-only	Number of retries made to install this soft PVC connection. If ciscoAtmVclConfigType is not soft then ciscoAtmVclNumAttempts value should be ignored.
ENA ciscoAtmVclOamAisEnable	1.3.6.1.4.1.9.10.13.1.2.1.1.10	EnableStatus	read-write	Enable Alarm Indication Signal OAM cell generation if the interafce goes down on a crossconnect virtual channel.
ENA ciscoAtmVclOamEndLoopback	1.3.6.1.4.1.9.10.13.1.2.1.1.9	EnableStatus	read-write	Enable end to end loopback on this virtual channel.
I32 ciscoAtmVclOamLoopbkTxInterval	1.3.6.1.4.1.9.10.13.1.2.1.1.7	Integer32	read-write	Frequency of OAM loopback cell are generated on this virtual channel.
ENA ciscoAtmVclOamRdiEnable	1.3.6.1.4.1.9.10.13.1.2.1.1.11	EnableStatus	read-write	Enable Remote Defect Indication OAM cell generation if an Alarm Indication Signal OAM cell is received.
ENA ciscoAtmVclOamSegmentLoopback	1.3.6.1.4.1.9.10.13.1.2.1.1.8	EnableStatus	read-write	Enable segment loopback on this virtual channel.
C32 ciscoAtmVclOutCells	1.3.6.1.4.1.9.10.13.1.2.1.1.14	Counter32	read-only	The total number of cells transmitted on this VCL.
C32 ciscoAtmVclOutClp0Cells	1.3.6.1.4.1.9.10.13.1.2.1.1.45	Counter32	read-only	The total number of cells with the CLP bit clear transmitted on this VCL. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
C32 ciscoAtmVclOutClp1Cells	1.3.6.1.4.1.9.10.13.1.2.1.1.46	Counter32	read-only	The total number of cells with the CLP bit set transmitted on this VCL. This counter is valid only: - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
NSA ciscoAtmVclRemoteAddr	1.3.6.1.4.1.9.10.13.1.2.1.1.25	NsapAtmAddr	read-write	Soft PVC target address if this is the calling side Soft PVC source address if this is called side. Atomically set ConnState, RemoteAddr, RemoteVpi and RemoteVci will create or delete a soft PVC. Atomically set ConnState, RemoteAddr without RemoteVpi, Remote Vci will also create or delete a soft PVC but let target switch assign the vpi and vci.
I32 ciscoAtmVclRemoteVci	1.3.6.1.4.1.9.10.13.1.2.1.1.27	Integer32	read-write	Soft PVC target VCI in calling side. 0 in called side.
I32 ciscoAtmVclRemoteVpi	1.3.6.1.4.1.9.10.13.1.2.1.1.26	Integer32	read-write	Soft PVC target VPI in calling side. 0 in called side.
ATM ciscoAtmVclRxNegTraffDescrIndex	1.3.6.1.4.1.9.10.13.1.2.1.1.50	AtmTrafficDescrParamIndex	read-only	Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the receive direction of this VCL. This object is not instantiated if this VCL is not the calling side of a soft VC, or if there was no traffic negotiation.
UPC ciscoAtmVclRxUpcMode	1.3.6.1.4.1.9.10.13.1.2.1.1.4	UpcStatus	read-write	Usage Parameter Control opeartion is pass,tag,drop or local shaping at this connection.
I32 ciscoAtmVclSlowRetryIntv	1.3.6.1.4.1.9.10.13.1.2.1.1.29	Integer32	read-write	Soft PVC slow retry interval in seconds.
SPA ciscoAtmVclSpanType	1.3.6.1.4.1.9.10.13.1.2.1.1.2	SpanType	read-only	Vcl span is either a transit one or a terminating one.
C32 ciscoAtmVclSwFabOutCells	1.3.6.1.4.1.9.10.13.1.2.1.1.52	Counter32	read-only	The total number of cells transmitted on this VCL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics.
C32 ciscoAtmVclSwFabOutClp0Cells	1.3.6.1.4.1.9.10.13.1.2.1.1.53	Counter32	read-only	The total number of cells with the CLP bit clear transmitted on this VCL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics.
C32 ciscoAtmVclSwFabOutClp1Cells	1.3.6.1.4.1.9.10.13.1.2.1.1.54	Counter32	read-only	The total number of cells with the CLP bit set transmitted on this VCL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics.
ciscoAtmVclTable	1.3.6.1.4.1.9.10.13.1.2.1		not-accessible	The Virtual Channel Link extension Table.
ATM ciscoAtmVclTxNegTraffDescrIndex	1.3.6.1.4.1.9.10.13.1.2.1.1.51	AtmTrafficDescrParamIndex	read-only	Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the transmit direction of this VCL. This object is not instantiated if this VCL is not the calling side of a soft VC, or if there was no traffic negotiation.
C32 ciscoAtmVclUpcViolations	1.3.6.1.4.1.9.10.13.1.2.1.1.32	Counter32	read-only	The total number of nonconforming cells detected by Usage Parameter Control (UPC) for cells received on this VCL. On LS1010 systems, this counter is valid only on those equipped with the Feature Card - Per Flow Queueing.
C32 ciscoAtmVclVcqClpThreshCellDrops	1.3.6.1.4.1.9.10.13.1.2.1.1.49	Counter32	read-only	The total number of cells received on this VCL, discarded because the discard threshold (as opposed to the queue-limit) is exceeded on the per-VC queue, and the CLP bit is set. This counter is valid only: - if EPD is disabled on the VCL. - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
ciscoAtmVpl	1.3.6.1.4.1.9.10.13.1.1
CAS ciscoAtmVplCastType	1.3.6.1.4.1.9.10.13.1.1.1.1.1	CastType	read-write	Vpl type is either a point to point connection or point to multipoint root or leaf.
C32 ciscoAtmVplCellDrops	1.3.6.1.4.1.9.10.13.1.1.1.1.41	Counter32	read-only	The total number of cells received on this VPL, but discarded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
C32 ciscoAtmVplClp0VcqFullCellDrops	1.3.6.1.4.1.9.10.13.1.1.1.1.43	Counter32	read-only	The total number of cells received on this VPL with the CLP bit clear, discarded because the per-VC queue limit is exceeded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
C32 ciscoAtmVplClp1Drops	1.3.6.1.4.1.9.10.13.1.1.1.1.30	Counter32	read-only	Never implemented.
CON ciscoAtmVplConfigType	1.3.6.1.4.1.9.10.13.1.1.1.1.3	ConfigType	read-write	Vpl type is either a PVC, SVC, Soft PVC or Soft Passive half leg. The half leg can be set to Passive through user configuration only.
STR ciscoAtmVplConnName	1.3.6.1.4.1.9.10.13.1.1.1.1.51	SnmpAdminString	read-write	A human readable string that identifies this connection. This object will return a zero-length string if value is not set.
CON ciscoAtmVplConnState	1.3.6.1.4.1.9.10.13.1.1.1.1.5	ConnState	read-write	The connection state of this VPL.
INT ciscoAtmVplConnType	1.3.6.1.4.1.9.10.13.1.1.1.1.52	INTEGER	read-write	This object represent the PVP Type for this connection. - local connection within the node - endToEnd across several nodes This object serves as an information object for a management system and has no functional meaning to the switch.
NUM ciscoAtmVplCrossIfIndex	1.3.6.1.4.1.9.10.13.1.1.1.1.14	InterfaceIndexOrZero	read-write	For point to point, this is the cross-connected VPL's ifIndex of this VPL. For point to multi-point connection, this will be the root VPL's ifIndex for a leaf VPL entry in the multicast chain, or it's the 1st leaf for a root VPL entry. If it's zero, it means it's not cross-connected yet. Atomically set ciscoAtmVplConnState, ciscoAtmVplCrossIfIndex and ciscoAtmVplCrossVpi will create or delete a cross connection to crossed half leg of this ciscoAtmVplCrossIfindex and ciscoAtmVplCrossVpi for p2p PVP, or add or drop a multicast connection of this ciscoAtmVplCrossIfindex and ciscoAtmVplCrossVpi to/from the root on the multicast chain for p2mp PVP.
I32 ciscoAtmVplCrossVpi	1.3.6.1.4.1.9.10.13.1.1.1.1.15	Integer32	read-write	This specifies the VPI value of the VPL to which this VPL is cross-connected. For point to multi-point connection, this is the root VPL's VPI for the leaf entry. Similarly it is the 1st leaf's VPI value for the root entry.
I32 ciscoAtmVplDefaultRxUpcTolerance	1.3.6.1.4.1.9.10.13.1.1.1.1.31	Integer32	read-only	If the tolerance (CDVT for CBR, ABR, UBR connections, Maximum Burst Size for VBR connectons) requested for Usage Parameter Control is not explicitly specified in VPL creation, this object contains the default that is used. If tolerance is explicitly specified in VPL creation, it can be found in the Traffic Table row specified by atmVplReceiveTrafficDescrIndex, and the value of this object is -1.
I32 ciscoAtmVplDefaultRxUpcVbrCdvt	1.3.6.1.4.1.9.10.13.1.1.1.1.32	Integer32	read-only	If the Cell Delay Variation Tolerance (CDVT) requested for Usage Parameter Control for a VBR connection is not explicitly specified in VPL creation, this object contains the default that is used. If CDVT is explicitly specified in VPL creation, it can be found in the Traffic Table row specified by atmVplReceiveTrafficDescrIndex, and the value of this object is -1.
ciscoAtmVplEntry	1.3.6.1.4.1.9.10.13.1.1.1.1		not-accessible	An entry in the Vpl table.This entry is used to model a bi-directional Vpl. This table augments the atmVplTable defined in RFC 1695. However it uses ifIndex and atmVplVpi as an Index for historical reasons. The entries are created/deleted as a by-product of creating and deleting entries in the atmVplTable.
C32 ciscoAtmVplEpdTpdCellDrops	1.3.6.1.4.1.9.10.13.1.1.1.1.27	Counter32	read-only	Never implemented.
C32 ciscoAtmVplEpdTpdPacketDrops	1.3.6.1.4.1.9.10.13.1.1.1.1.28	Counter32	read-only	Never implemented.
C32 ciscoAtmVplEpdTpdPacketsIn	1.3.6.1.4.1.9.10.13.1.1.1.1.29	Counter32	read-only	Never implemented.
C32 ciscoAtmVplInCells	1.3.6.1.4.1.9.10.13.1.1.1.1.12	Counter32	read-only	The total number of cells received on this VPL.
C32 ciscoAtmVplInClp0CellsEx	1.3.6.1.4.1.9.10.13.1.1.1.1.37	Counter32	read-only	The total number of cells with the CLP bit clear received on this VPL. Note that these cells may subsequently be discarded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
C32 ciscoAtmVplInClp1Cells	1.3.6.1.4.1.9.10.13.1.1.1.1.38	Counter32	read-only	The total number of cells with the CLP bit set received on this VPL. Note that these cells may subsequently be discarded. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.
TIM ciscoAtmVplInstallTime	1.3.6.1.4.1.9.10.13.1.1.1.1.11	TimeStamp	read-only	The time stamp derived from sysUpTime when this VPL gets created. The VPL entries are created/deleted as a by-product of creating and deleting entries in the atmVplTable defined in RFC1695.
I32 ciscoAtmVplLastReleaseCause	1.3.6.1.4.1.9.10.13.1.1.1.1.23	Integer32	read-only	Value of the Cause field of the Cause Information Element in the last Release Signalling message received for this SPVP. Indicates the reason for the Release. ciscoAtmVplConfigType is not soft then ciscoAtmVplLastReleaseCause value should be ignored.
LOC ciscoAtmVplLocation	1.3.6.1.4.1.9.10.13.1.1.1.1.20	Location	read-only	Indicate calling or called side of a soft PVP. If ciscoAtmVplConfigType is not soft then ciscoAtmVplLocation value should be ignored.
INT ciscoAtmVplLogicalPortDef	1.3.6.1.4.1.9.10.13.1.1.1.1.24	INTEGER	read-write	Indicates whether the VPC at this VPL interface is an Atm Logical Port interface.
NUM ciscoAtmVplLogicalPortIndex	1.3.6.1.4.1.9.10.13.1.1.1.1.25	InterfaceIndexOrZero	read-only	The ifTable index of the Atm logical port interface associated with this VPL. Only valid if the value of atmVplLogicalPortDef is isLogicalIf, and the VPL row is active.
LSP ciscoAtmVplLsPerVcQThreshGrp	1.3.6.1.4.1.9.10.13.1.1.1.1.36	LsPerVcqThresholdGroup	read-only	The Threshold Group to which the cell-queue for cells received by this VP are queued. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset.
T/F ciscoAtmVplLsPerVcqTunnelIsHierarchical	1.3.6.1.4.1.9.10.13.1.1.1.1.45	TruthValue	read-write	Determines whether this is to be a -Hierarchical- VP, per the Lightstream per-VC queueing chipset. If the value specified is TRUE, the VP is to be a Hierarchical VP Tunnel. Such a VP cannot be cross-connected. This object is defined on a LS1010 only when the switch is equipped with the Lightstream per-VC queueing chipset.
T/F ciscoAtmVplLsPerVcqTunnelIsShaped	1.3.6.1.4.1.9.10.13.1.1.1.1.34	TruthValue	read-write	Determines whether this is to be a -shaped- VP, per the Lightstream per-VC queueing chipset. If the value specified is TRUE, the VP is to be a shaped VP Tunnel. Such a VP cannot be cross-connected. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset.
INT ciscoAtmVplLsPerVcqWrrWeight	1.3.6.1.4.1.9.10.13.1.1.1.1.33	INTEGER	read-write	Configure the weighting specified for a VP half-leg within a service class to make the scheduling decision among other active VPLs in the service class. This is for transmit on the VPL on the interface. This parameter only applies to transit VPs. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset.
G32 ciscoAtmVplLsPerVcqXmtQueuedCells	1.3.6.1.4.1.9.10.13.1.1.1.1.35	Gauge32	read-only	Number of cells received on this VPL and residing on the per-connection queue. Note that this value is not valid until the VPL is in an active cross-connect. This object is defined only when the switch is equipped with the Lightstream per-VC queueing chipset.
NUM ciscoAtmVplNextLeafIfIndex	1.3.6.1.4.1.9.10.13.1.1.1.1.16	InterfaceIndexOrZero	read-only	For point to point, this is zero i.e. not used. For point to multi-point connection, this will be the next leaf VPL's ifIndex on the multicast chain. This will be 0 if this is the root VPL entry. If it's zero for a leaf VPL, it means this is the last leaf.
I32 ciscoAtmVplNextLeafVpi	1.3.6.1.4.1.9.10.13.1.1.1.1.17	Integer32	read-only	For point to point, this is zero i.e. not used. This apply only to point to multi-point connection, this will be the next leaf VPL's VPI on the multicast chain.
C32 ciscoAtmVplNumAttempts	1.3.6.1.4.1.9.10.13.1.1.1.1.22	Counter32	read-only	Number of retries made to install this soft PVP connection. If ciscoAtmVplConfigType is not soft then ciscoAtmVplNumAttempts value should be ignored.
ENA ciscoAtmVplOamAisEnable	1.3.6.1.4.1.9.10.13.1.1.1.1.9	EnableStatus	read-write	Enable Alarm Indication Signal OAM cell generation if the interafce goes down on a crossconnect virtual path.
ENA ciscoAtmVplOamEndLoopback	1.3.6.1.4.1.9.10.13.1.1.1.1.8	EnableStatus	read-write	Enable end to end loopback on this virtual path.
I32 ciscoAtmVplOamLoopbkTxInterval	1.3.6.1.4.1.9.10.13.1.1.1.1.6	Integer32	read-write	Frequency of OAM loopback cells generated.
ENA ciscoAtmVplOamRdiEnable	1.3.6.1.4.1.9.10.13.1.1.1.1.10	EnableStatus	read-write	Enable Remote Defect Indication OAM cell generation if an Alarm Indication Signal OAM cell is received.
ENA ciscoAtmVplOamSegmentLoopback	1.3.6.1.4.1.9.10.13.1.1.1.1.7	EnableStatus	read-write	Enable segment loopback on this virtual path.
C32 ciscoAtmVplOutCells	1.3.6.1.4.1.9.10.13.1.1.1.1.13	Counter32	read-only	The total number of cells transmitted on this VPL.
C32 ciscoAtmVplOutClp0Cells	1.3.6.1.4.1.9.10.13.1.1.1.1.39	Counter32	read-only	The total number of cells with the CLP bit clear transmitted on this VPL. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing.
C32 ciscoAtmVplOutClp1Cells	1.3.6.1.4.1.9.10.13.1.1.1.1.40	Counter32	read-only	The total number of cells with the CLP bit set transmitted on this VPL. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with the Feature Card - Per Flow Queueing.
NSA ciscoAtmVplRemoteAddr	1.3.6.1.4.1.9.10.13.1.1.1.1.18	NsapAtmAddr	read-write	Soft PVP target address if this is the calling side Soft PVP source address if this is called side. Atomically set ConnState, RemoteAddr and RemoteVpi will create or delete a soft PVP. Atomically set ConnState, RemoteAddr without RemoteVpi will also create or delete a soft PVP but let target switch assign the vpi.
I32 ciscoAtmVplRemoteVpi	1.3.6.1.4.1.9.10.13.1.1.1.1.19	Integer32	read-write	Soft PVP target VPI in calling side. 0 in called side.
ATM ciscoAtmVplRxNegTraffDescrIndex	1.3.6.1.4.1.9.10.13.1.1.1.1.46	AtmTrafficDescrParamIndex	read-only	Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the receive direction of this VPL. This object is not instantiated if this VPL is not the calling side of a soft VP, or if there was no traffic negotiation.
UPC ciscoAtmVplRxUpcMode	1.3.6.1.4.1.9.10.13.1.1.1.1.4	UpcStatus	read-write	Usage Parameter Control opeartion is pass,tag,drop or local shaping at this connection.
I32 ciscoAtmVplSlowRetryIntv	1.3.6.1.4.1.9.10.13.1.1.1.1.21	Integer32	read-write	Soft PVP slow retry interval time in seconds.
SPA ciscoAtmVplSpanType	1.3.6.1.4.1.9.10.13.1.1.1.1.2	SpanType	read-only	Vpl span is either a transit one or a terminating one.
C32 ciscoAtmVplSwFabOutCells	1.3.6.1.4.1.9.10.13.1.1.1.1.48	Counter32	read-only	The total number of cells transmitted on this VPL by the Switch Fabric. This object is not instantiated on systems that do not have support for collecting such statistics.
C32 ciscoAtmVplSwFabOutClp0Cells	1.3.6.1.4.1.9.10.13.1.1.1.1.49	Counter32	read-only	The total number of cells with the CLP bit clear transmitted on this VPL by the Switch Fabric. This object is not instantiated for a VPL that is a logical interface (VP Tunnel). This object is not instantiated on systems that do not have support for collecting such statistics.
C32 ciscoAtmVplSwFabOutClp1Cells	1.3.6.1.4.1.9.10.13.1.1.1.1.50	Counter32	read-only	The total number of cells with the CLP bit set transmitted on this VPL by the Switch Fabric. This object is not instantiated for a VPL that is a logical interface (VP Tunnel). This object is not instantiated on systems that do not have support for collecting such statistics.
ciscoAtmVplTable	1.3.6.1.4.1.9.10.13.1.1.1		not-accessible	The Virtual Path Link extension Table.
ATM ciscoAtmVplTxNegTraffDescrIndex	1.3.6.1.4.1.9.10.13.1.1.1.1.47	AtmTrafficDescrParamIndex	read-only	Identifies the entry in the atmTrafficDescrParamTable which contains negotiated traffic parameters applied to the transmit direction of this VPL. This object is not instantiated if this VPL is not the calling side of a soft VP, or if there was no traffic negotiation.
C32 ciscoAtmVplUpcViolations	1.3.6.1.4.1.9.10.13.1.1.1.1.26	Counter32	read-only	The total number of nonconforming cells detected by Usage Parameter Control (UPC) for cells received on this VPL. On LS1010 systems, this counter is valid only if equipped with the Feature Card - Per Flow Queueing.
C32 ciscoAtmVplVcqClpThreshCellDrops	1.3.6.1.4.1.9.10.13.1.1.1.1.44	Counter32	read-only	The total number of cells received on this VPL, discarded because the discard threshold (as opposed to the queue-limit) is exceeded on the per-VC queue, and the CLP bit is set. This counter is valid only: - if the VPL is not a Logical Interface (tunnel). - on LS1010 systems, only those equipped with Feature Card - Per Flow Queueing.

RFC description

Extends ATM connection management for Cisco switches with per-connection statistics and transmission monitoring on VPL/VCL tables.

Start monitoring Cisco ATM switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download CISCO-ATM-CONN-MIB