All MIBs › ASCEND-MIB
Category: Device Management, Vendor: Ascend/Lucent
Description: Primary Ascend Communications MIB providing device configuration and status for WAN access equipment.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ASCEND-MIB?
ASCEND-MIB is Ascend Communications' primary enterprise MIB, defining the vendor-specific management objects for the company's WAN access and remote-access dial-up equipment, such as its MAX and Pipeline product lines (Ascend was later acquired by Lucent). It exposes configuration and operational status data for these WAN access devices, spanning system-level identification, interface/port configuration, and device status categories. It plays a direct role in monitoring hardware and software status on Ascend WAN access gear, and network operators query objects under the ASCEND-MIB OID tree to confirm system uptime, WAN interface/port operational state, and overall device health on these units. Like most enterprise MIBs, it depends on standard SNMP framework definitions (such as SNMPv2-SMI and SNMPv2-TC) for its base data types even as it defines Ascend-specific structures. It is typically deployed on Ascend Communications WAN access concentrators and remote-access routers in ISP and enterprise dial-up/WAN aggregation environments.
IPNetwork Monitor allows you to monitor SNMP objects defined in ASCEND-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Ascend Communications MAX and Pipeline WAN access/dial-up equipment
Monitoring Examples
No sample objects were available for this module, so specific object names cannot be confirmed here; broadly, however, an administrator monitoring an Ascend MAX or Pipeline unit through ASCEND-MIB would poll system identification and status scalars alongside WAN interface/port configuration and state tables to confirm the device is operating normally. Exact OIDs and table names should be verified against the actual MIB source rather than assumed.
What Can Be Monitored
- system uptime
- WAN interface/port status
- device configuration state
- system identification
This MIB depends on
Related MIBs
Imported Objects
From RFC-1212
| OBJECT-TYPE |
From RFC1155-SMI
| IpAddress | |
| TimeTicks | |
| enterprises |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| advancedAgent | 1.3.6.1.4.1.529.4 | |||
| apx_8000 | 1.3.6.1.4.1.529.1.8 | |||
| aq300 | 1.3.6.1.4.1.529.1.6.1 | |||
| aqueduct | 1.3.6.1.4.1.529.1.6 | |||
| ascend | 1.3.6.1.4.1.529 | |||
| asgGroup | 1.3.6.1.4.1.529.21 | |||
| atmpGroup | 1.3.6.1.4.1.529.24 | |||
| callLoggingGroup | 1.3.6.1.4.1.529.25 | |||
| callStatusGroup | 1.3.6.1.4.1.529.11 | |||
| cltmGroup | 1.3.6.1.4.1.529.31 | |||
| configuration | 1.3.6.1.4.1.529.23 | |||
| console | 1.3.6.1.4.1.529.8 | |||
| consoleEntry | 1.3.6.1.4.1.529.8.2.1 | not-accessible | An entry containing objects that describe the indexed console port. | |
| INT consoleIf | 1.3.6.1.4.1.529.8.2.1.2 | INTEGER | read-only | The interface number associated with the indexed console. This number can be used to index into the interface (and other) tables to obtain detailed console status. |
| INT consoleIndex | 1.3.6.1.4.1.529.8.2.1.1 | INTEGER | read-only | A unique value for each console. It's value ranges between 1 and the value consoleNumber. This is the index into the console table to identify a particular console. |
| INT consoleNumber | 1.3.6.1.4.1.529.8.1 | INTEGER | read-only | The number of consoles supported by this device. |
| INT consoleSecurity | 1.3.6.1.4.1.529.8.2.1.4 | INTEGER | read-only | The security profile, in the range of 1 through the number of profiles supported by the unit, of the indexed console. The default security profile is profile number 1. Note: This attribute is supported on non-TNT platforms only. |
| OID consoleSpecific | 1.3.6.1.4.1.529.8.2.1.5 | OBJECT IDENTIFIER | read-only | A reference to MIB definitions specific to the console port. Contains the object identifier { 0 0 } if there is no console specific information for the indexed console. |
| consoleTable | 1.3.6.1.4.1.529.8.2 | not-accessible | A list of console entries. | |
| INT consoleType | 1.3.6.1.4.1.529.8.2.1.3 | INTEGER | read-only | The type of console in the indexed entry. When no console is plugged into a console port the value inactive(5) is returned. The value remote(6) indicates a console initiated via remote management or TELNET session. |
| cvmax100 | 1.3.6.1.4.1.529.1.2.12 | |||
| INT doAnswer | 1.3.6.1.4.1.529.6.1.1.5 | INTEGER | read-write | When read returns valid if the indexed slot/item can answer a call. Writing any value will cause the call to be answered when valid, otherwise the write is ignored. |
| INT doBegEndBERT | 1.3.6.1.4.1.529.6.1.1.9 | INTEGER | read-write | When read returns valid if the indexed slot/item can enter or exit BERT test mode. Writing any value will cause the current BERT test state to be toggled when valid, otherwise the write is ignored. |
| INT doBegEndRemoteLB | 1.3.6.1.4.1.529.6.1.1.8 | INTEGER | read-write | When read returns valid if the indexed slot/item can enter or exit remote loopback. Writing any value will cause the current remote loopback state to be toggled when valid, otherwise the write is ignored. |
| INT doContractBW | 1.3.6.1.4.1.529.6.1.1.7 | INTEGER | read-write | When read returns valid if the indexed slot/item can contract bandwidth. Writing any value will cause bandwidth to be contracted when valid, otherwise the write is ignored. |
| INT doDial | 1.3.6.1.4.1.529.6.1.1.3 | INTEGER | read-write | When read returns valid if the indexed slot/item can dial a call. Writing any value will cause a call to be placed when valid, otherwise the write is ignored. |
| doEntry | 1.3.6.1.4.1.529.6.1.1 | not-accessible | An entry containing all of the action (do) commands and the slot and item index. | |
| INT doExtendBW | 1.3.6.1.4.1.529.6.1.1.6 | INTEGER | read-write | When read returns valid if the indexed slot/item can extend bandwidth. Writing any value will cause bandwidth to be extended when valid, otherwise the write is ignored. |
| doGroup | 1.3.6.1.4.1.529.6 | |||
| INT doHangUp | 1.3.6.1.4.1.529.6.1.1.4 | INTEGER | read-write | When read returns valid if the indexed slot/item can terminate a call. Writing any value will cause the call to be terminated when valid, otherwise the write is ignored. |
| INT doItemIndex | 1.3.6.1.4.1.529.6.1.1.2 | INTEGER | read-only | The item number on the indexed slot for which an action is desired. The valid range is 1 through the value slotItems in the slotTable when indexed by a value equal to doSlotIndex. |
| INT doResynchronize | 1.3.6.1.4.1.529.6.1.1.10 | INTEGER | read-write | When read returns valid if the indexed slot/item can issue a resynchronize command. Writing any value will cause a resynchronize command to be issued when valid, otherwise the write is ignored. |
| INT doSlotIndex | 1.3.6.1.4.1.529.6.1.1.1 | INTEGER | read-only | The index of the slot containing the item for which an action is desired. The valid range is 1 through the value slotNumber. |
| doTable | 1.3.6.1.4.1.529.6.1 | not-accessible | A list of do entries. | |
| dslmax20 | 1.3.6.1.4.1.529.1.2.10 | |||
| dslPipe2S | 1.3.6.1.4.1.529.1.3.12 | |||
| dslPipe50SdslCell | 1.3.6.1.4.1.529.1.3.25 | |||
| dslPipeAcap | 1.3.6.1.4.1.529.1.3.10 | |||
| dslPipeAdmt | 1.3.6.1.4.1.529.1.3.21 | |||
| dslPipeAdslCoeC | 1.3.6.1.4.1.529.1.3.13 | |||
| dslPipeAdslCoeD | 1.3.6.1.4.1.529.1.3.20 | |||
| dslPipeAlctlDmt | 1.3.6.1.4.1.529.1.3.22 | |||
| dslPipeS | 1.3.6.1.4.1.529.1.3.11 | |||
| dslPipeSdslCoe | 1.3.6.1.4.1.529.1.3.14 | |||
| dslPipeSdslCoe2S | 1.3.6.1.4.1.529.1.3.15 | |||
| dslPipeSdslHs | 1.3.6.1.4.1.529.1.3.26 | |||
| dslTnt | 1.3.6.1.4.1.529.1.5 | |||
| eventGroup | 1.3.6.1.4.1.529.10 | |||
| INT fatalLogAbsoluteTime | 1.3.6.1.4.1.529.9.16.1.8 | INTEGER | read-only | The time at which the system was reset. |
| INT fatalLogIndex | 1.3.6.1.4.1.529.9.16.1.1 | INTEGER | read-only | Dynamic index that reflects the index used in the Fatal LOG table, starting with the most oldest event. |
| STR fatalLogLoadName | 1.3.6.1.4.1.529.9.16.1.5 | DisplayString | read-only | The name of the Load executing on the card, it gives a textual description of the software code that was running on the system when the entry was created. |
| STR fatalLogLocation | 1.3.6.1.4.1.529.9.16.1.6 | DisplayString | read-only | The IP address from which a manual system reset was triggered. |
| INT fatalLogReason | 1.3.6.1.4.1.529.9.16.1.7 | INTEGER | read-only | The reason for reset as reported by the system. For a more detailed description consult the user manual. |
| INT fatalLogSlotIndex | 1.3.6.1.4.1.529.9.16.1.2 | INTEGER | read-only | An index into the slotTable This has the same value as slotIndex, it is set to 0 for systems with one logical slot card. |
| STR fatalLogSoftwareVerion | 1.3.6.1.4.1.529.9.16.1.3 | DisplayString | read-only | The version of the software running, when this entry was created by the system. |
| fatalLogTable | 1.3.6.1.4.1.529.9.16 | not-accessible | A list of the most recent Fatal Log entries of the system as well as the included slot cards | |
| fatalLogTableEntry | 1.3.6.1.4.1.529.9.16.1 | not-accessible | Definition of the row entries in the Fatal Log Table | |
| STR fatalLogUserprofile | 1.3.6.1.4.1.529.9.16.1.4 | DisplayString | read-only | The user responsible for reseting the card. This will be set to the empty string if unknown. |
| firewallGroup | 1.3.6.1.4.1.529.16 | |||
| flashGroup | 1.3.6.1.4.1.529.22 | |||
| hostStatus | 1.3.6.1.4.1.529.7 | |||
| INT hostStatusCallMgm | 1.3.6.1.4.1.529.7.1.1.6 | INTEGER | read-only | The call management protocol from the current call profile for the indexed host slot and port. Call management is only meaningful for calls using an inverse multiplexing protocol. |
| INT hostStatusCallState | 1.3.6.1.4.1.529.7.1.1.8 | INTEGER | read-only | Shows the current state of the current call for the indexed host slot and port. The returned value will indicates the same state displayed in a call status window for the port. |
| INT hostStatusCallType | 1.3.6.1.4.1.529.7.1.1.5 | INTEGER | read-only | The type of call from the current call profile of the indexed host slot and port. |
| INT hostStatusChannels | 1.3.6.1.4.1.529.7.1.1.10 | INTEGER | read-only | The number of channels in use by the call as displayed on the third line of the call status menu for the indexed slot and port. |
| INT hostStatusDataSvc | 1.3.6.1.4.1.529.7.1.1.7 | INTEGER | read-only | The type of service from the current call profile for the indexed host slot and port. |
| OCT hostStatusDialNum | 1.3.6.1.4.1.529.7.1.1.4 | OCTET STRING | read-only | The phone number from the current call profile of the indexed host slot and port. |
| INT hostStatusDuration | 1.3.6.1.4.1.529.7.1.1.11 | INTEGER | read-only | The duration of the call associated with the indexed host slot and port, measured in seconds. |
| hostStatusEntry | 1.3.6.1.4.1.529.7.1.1 | not-accessible | An entry containing the host port status of the indexed slot/item. | |
| INT hostStatusItemIndex | 1.3.6.1.4.1.529.7.1.1.2 | INTEGER | read-only | Index to each item defined for each slot. Since entries in this table are only valid for host ports an item number is a port number within the indexed slot. |
| OCT hostStatusLocalName | 1.3.6.1.4.1.529.7.1.1.3 | OCTET STRING | read-only | The name from the current call profile of the indexed host slot and port. |
| OCT hostStatusRemName | 1.3.6.1.4.1.529.7.1.1.9 | OCTET STRING | read-only | The value displayed on the 4th line of the call status menu. When the hostStatusCallType is aim( 1 ) this value is the name of the host port on the far end of a connection, or the far-end system name if the host port has not been named. An empty string is returned when there is no call active or when aim( 1 ) is not being used. |
| INT hostStatusSlotIndex | 1.3.6.1.4.1.529.7.1.1.1 | INTEGER | read-only | A unique value for each slot. The slot identified by a particular value of this index is the same slot as identified by the same value of slotIndex. |
| hostStatusTable | 1.3.6.1.4.1.529.7.1 | not-accessible | A table of host port status entries. A host port status entry potentialy exists for every slot/item. Host port status entries are only meaningful for slot/items that reference a host port. When indexed by other slot/items NO SUCH NAME will be returned. | |
| hostTypeAim2 | 1.3.6.1.4.1.529.3.4 | |||
| hostTypeAim6 | 1.3.6.1.4.1.529.3.5 | |||
| hostTypeAny | 1.3.6.1.4.1.529.3.1 | |||
| hostTypeDual | 1.3.6.1.4.1.529.3.2 | |||
| hostTypeQuad | 1.3.6.1.4.1.529.3.3 | |||
| hostTypes | 1.3.6.1.4.1.529.3 | |||
| lanModemGroup | 1.3.6.1.4.1.529.15 | |||
| lanTypeAny | 1.3.6.1.4.1.529.5.1 | |||
| lanTypeEtherData | 1.3.6.1.4.1.529.5.3 | |||
| lanTypeEthernet | 1.3.6.1.4.1.529.5.2 | |||
| lanTypes | 1.3.6.1.4.1.529.5 | |||
| max | 1.3.6.1.4.1.529.1.2 | |||
| max_tnt | 1.3.6.1.4.1.529.1.4 | |||
| max1800 | 1.3.6.1.4.1.529.1.2.2 | |||
| max200 | 1.3.6.1.4.1.529.1.2.1 | |||
| max2000 | 1.3.6.1.4.1.529.1.2.3 | |||
| max3000 | 1.3.6.1.4.1.529.1.2.9 | |||
| max4000 | 1.3.6.1.4.1.529.1.2.4 | |||
| max4002 | 1.3.6.1.4.1.529.1.2.5 | |||
| max4004 | 1.3.6.1.4.1.529.1.2.6 | |||
| max6000 | 1.3.6.1.4.1.529.1.2.7 | |||
| max800 | 1.3.6.1.4.1.529.1.2.8 | |||
| mCastGroup | 1.3.6.1.4.1.529.14 | |||
| mgGroup | 1.3.6.1.4.1.529.29 | |||
| mibanswerProfile | 1.3.6.1.4.1.529.23.3 | |||
| mibcadslNetworkProfile | 1.3.6.1.4.1.529.23.6 | |||
| mibdadslNetworkProfile | 1.3.6.1.4.1.529.23.7 | |||
| mibdmtAlDslNetworkProfile | 1.3.6.1.4.1.529.23.10 | |||
| mibds3AtmNetworkProfile | 1.3.6.1.4.1.529.23.13 | |||
| mibdS3NetworkProfile | 1.3.6.1.4.1.529.23.4 | |||
| mibe3AtmNetworkProfile | 1.3.6.1.4.1.529.23.15 | |||
| mibframeRelayProfile | 1.3.6.1.4.1.529.23.2 | |||
| mibhdsl2NetworkProfile | 1.3.6.1.4.1.529.23.14 | |||
| mibinternetProfile | 1.3.6.1.4.1.529.23.1 | |||
| miblimSparingConfigProfile | 1.3.6.1.4.1.529.23.12 | |||
| miboc3AtmNetworkProfile | 1.3.6.1.4.1.529.23.11 | |||
| mibredundancyProfile | 1.3.6.1.4.1.529.23.16 | |||
| mibredundancyStatsProfile | 1.3.6.1.4.1.529.23.17 | |||
| mibsdslNetworkProfile | 1.3.6.1.4.1.529.23.8 | |||
| mibuds3NetworkProfile | 1.3.6.1.4.1.529.23.5 | |||
| mibvdslNetworkProfile | 1.3.6.1.4.1.529.23.9 | |||
| miscGroup | 1.3.6.1.4.1.529.20 | |||
| multiband | 1.3.6.1.4.1.529.1.1 | |||
| multiShelf | 1.3.6.1.4.1.529.19 | |||
| pipe130N56 | 1.3.6.1.4.1.529.1.3.19 | |||
| pipe130T1 | 1.3.6.1.4.1.529.1.3.7 | |||
| pipe130V35 | 1.3.6.1.4.1.529.1.3.18 | |||
| pipe15 | 1.3.6.1.4.1.529.1.3.1 | |||
| pipe220 | 1.3.6.1.4.1.529.1.3.9 | |||
| pipe25 | 1.3.6.1.4.1.529.1.3.2 | |||
| pipe25Fx | 1.3.6.1.4.1.529.1.3.4 | |||
| pipe25Px | 1.3.6.1.4.1.529.1.3.3 | |||
| pipe400 | 1.3.6.1.4.1.529.1.3.8 | |||
| pipe50 | 1.3.6.1.4.1.529.1.3.5 | |||
| pipe50LS56 | 1.3.6.1.4.1.529.1.3.17 | |||
| pipe75 | 1.3.6.1.4.1.529.1.3.6 | |||
| pipe85 | 1.3.6.1.4.1.529.1.3.16 | |||
| pipeline | 1.3.6.1.4.1.529.1.3 | |||
| powerSupply | 1.3.6.1.4.1.529.18 | |||
| products | 1.3.6.1.4.1.529.1 | |||
| radiusGroup | 1.3.6.1.4.1.529.13 | |||
| resetStat | 1.3.6.1.4.1.529.9.12 | |||
| INT resetStatAll | 1.3.6.1.4.1.529.9.12.3 | INTEGER | read-write | Clear all WAN statistics. |
| INT resetStatEther | 1.3.6.1.4.1.529.9.12.1 | INTEGER | read-write | Clear Ethernet statistics. |
| INT resetStatWAN | 1.3.6.1.4.1.529.9.12.2 | INTEGER | read-write | Clear specified interface's WAN statistics. |
| resourcesGroup | 1.3.6.1.4.1.529.27 | |||
| sessionStatusGroup | 1.3.6.1.4.1.529.12 | |||
| slots | 1.3.6.1.4.1.529.2 | |||
| sparingGroup | 1.3.6.1.4.1.529.30 | |||
| spipe155T1 | 1.3.6.1.4.1.529.1.3.24 | |||
| spipe95 | 1.3.6.1.4.1.529.1.3.23 | |||
| srvcMgmtGroup | 1.3.6.1.4.1.529.26 | |||
| stinger_10 | 1.3.6.1.4.1.529.1.7 | |||
| INT sysAbsoluteCurrentTime | 1.3.6.1.4.1.529.9.7 | INTEGER | read-write | The current system time in seconds since January 1, 1990. Changing this value may result in a change of sysAbsoluteStartupTime and not of sysSecsSinceStartup. The following relationship holds: sysAbsoluteCurrentTime - sysAbsoluteStartupTime = sysSecsSinceStartup. |
| INT sysAbsoluteStartupTime | 1.3.6.1.4.1.529.9.1 | INTEGER | read-only | The time system startup up in seconds since January 1, 1990. This value in concert with 'sysSecsSinceStartup' below can be used to compute the current time in seconds since 1/1/90. |
| INT sysAuthPreference | 1.3.6.1.4.1.529.9.10 | INTEGER | read-write | An incoming call can be authenticated using a local profile or one from an authentication server such as RADIUS or TACACS. local-first means authenticate from a local profile first, and if that fails, try the authentication server. remote-first means get a profile from the authentication server and authenticate from that and if that fails, try to authenticate from a local profile. remote-no is the same as remote-first except if the external authentication server NACKs the request, then the connection will be denied, i.e. no search of the local profiles will be made. |
| STR sysConfigChange | 1.3.6.1.4.1.529.9.14 | DisplayString | read-only | The name and security index (if available) of the user who changed the configuration. |
| sysConfigFlash | 1.3.6.1.4.1.529.9.15 | |||
| INT sysConfigFlashCmd | 1.3.6.1.4.1.529.9.15.1 | INTEGER | read-write | This variable instructs the system to copy the stored code image from PCMCIA flash to internal flash or vice versa. |
| INT sysConfigFlashCopyStatus | 1.3.6.1.4.1.529.9.15.2 | INTEGER | read-only | This variable indicates the status of a flash image copy. |
| STR sysConfigInternalFlashImageVersion | 1.3.6.1.4.1.529.9.15.3 | DisplayString | read-only | The code version stored on the internal flash. |
| STR sysConfigPCMCIAFlashImageVersion | 1.3.6.1.4.1.529.9.15.4 | DisplayString | read-only | The code version stored on the PCMCIA flash. |
| sysConfigRadius | 1.3.6.1.4.1.529.9.6 | |||
| INT sysConfigRadiusCmd | 1.3.6.1.4.1.529.9.6.1 | INTEGER | read-write | This variable instructs the system to re-read its RADIUS configuration. This variable will return a general error if RADIUS is not configured or if sysConfigRadiusStatus has a value of processing(2). |
| INT sysConfigRadiusStatus | 1.3.6.1.4.1.529.9.6.2 | INTEGER | read-only | This variable indicates the status of the last RADIUS configuration retrieval. This includes the boot time retrieval. |
| sysConfigTftp | 1.3.6.1.4.1.529.9.5 | |||
| INT sysConfigTftpCmd | 1.3.6.1.4.1.529.9.5.1 | INTEGER | read-write | This variable instructs the system to perform the specified tftp operation. Note: loadCode( 6 ) is not supported on TNT platform. |
| STR sysConfigTftpFilename | 1.3.6.1.4.1.529.9.5.4 | DisplayString | read-write | This variable indicates the file name of the configuration file to save to or restore from a SNMP host through tftp. |
| IP sysConfigTftpHostAddr | 1.3.6.1.4.1.529.9.5.3 | IpAddress | read-write | This variable indicates the host address where the configuration file is saved to or restored from through tftp. |
| STR sysConfigTftpParameter | 1.3.6.1.4.1.529.9.5.6 | DisplayString | read-write | This variable indicates the list of profiles to be included or excluded during the save operation through tftp. The snmp agent will modify the set string to an uppercase space-separated new string and return the changed value. This is to clarify the case insensitive profile naming. |
| INT sysConfigTftpPort | 1.3.6.1.4.1.529.9.5.5 | INTEGER | read-write | This variable indicates the port # to use when starting a TSAVE TRESTORE command. Normally this would be port 69, but we need to allow the Java Console to override this in case the Console workstation has a TFTP server already running. |
| INT sysConfigTftpStatus | 1.3.6.1.4.1.529.9.5.2 | INTEGER | read-only | This variable indicates the status of a save or restore operation through tftp. |
| INT sysLastRestartReason | 1.3.6.1.4.1.529.9.13 | INTEGER | read-only | The error code for the previous box restart. The error codes are identical to ones obtained via fatal-history from the debug monitor screen. |
| STR sysLoadName | 1.3.6.1.4.1.529.9.9 | DisplayString | read-only | The name of the load which is currently running. |
| INT sysMibMinorRevNum | 1.3.6.1.4.1.529.9.4 | INTEGER | read-only | Value represents the minor revision number of this MIB. Minor revision numbers start at 0 and increment by 1 for each revision. Minor revisions are textual or comment changes. |
| INT sysMibVersionNum | 1.3.6.1.4.1.529.9.3 | INTEGER | read-only | Version number of this private MIB. Versions numbers start at 1 and increment by 1 for every major revision. Major revisions are additions/deletions to this MIB. |
| INT sysReset | 1.3.6.1.4.1.529.9.8 | INTEGER | read-write | The reset takes effect after 1 minute. |
| INT sysSecsSinceStartup | 1.3.6.1.4.1.529.9.2 | INTEGER | read-only | The number of seconds since system startup. |
| sysSPROM | 1.3.6.1.4.1.529.9.11 | |||
| INT sysSPROMCountries1 | 1.3.6.1.4.1.529.9.11.4 | INTEGER | read-only | The various bit positions are: (2 ** 0) - FranceIsdn (2 ** 1) - UKIsdn (2 ** 2) - BelgiumIsdn (2 ** 3) - JapanIsdn (2 ** 4) - AustraliaIsdn (2 ** 5) - GermanIsdn (2 ** 6) - UKDpnss (2 ** 7) - SwissIsdn (2 ** 8) - GloBandIsdn |
| INT sysSPROMOptions1 | 1.3.6.1.4.1.529.9.11.2 | INTEGER | read-only | The various bit positions are: (2 ** 0) - rs366Enabled (2 ** 1) - dChannelEnabled (2 ** 2) - autoDBAEnabled (2 ** 3) - bondingEnabled (2 ** 4) - aimEnabled (2 ** 5) - v25bisEnabled (2 ** 6) - x21Enabled (2 ** 7) - switchedEnabled (2 ** 8) - mrateEnabled (2 ** 9) - pbxEnabled (2 ** 10) - pcbusEnabled (2 ** 11) - bridgingEnabled (2 ** 12) - pipeHxEnabled (2 ** 13) - frameRelayEnabled (2 ** 14) - maxLinkClientEnabled (2 ** 15) - dataCallEnabled (2 ** 16) - dualSlotT1Enabled (2 ** 17) - r2SignalingEnabled (2 ** 18) - domesticEnabled (2 ** 19) - modemTSDialoutEnabled (2 ** 20) - pipePxEnabled (2 ** 21) - firewallsEnabled (2 ** 22) - serialPortT1_CSU_Enabled (2 ** 23) - pipePotsEnabled (2 ** 24) - forceMultibandPlatformSimulationEnabled (2 ** 25) - k56SlotCardOnlyEnabled (2 ** 26) - networkManagementEnabled (2 ** 27) - advancedAgentEnabled (DEPRECATED) (2 ** 28) - phsSupportEnabled (2 ** 29) - selectoolsEnabled (2 ** 30) - routingProtocolsDisabled (2 ** 31) - tunnelProtocolsDisabled (DEPRECATED). |
| INT sysSPROMOptions2 | 1.3.6.1.4.1.529.9.11.3 | INTEGER | read-only | The various bit positions are: (2 ** 0) - atmpEnabled (2 ** 1) - l2tpEnabled (2 ** 2) - pptpEnabled (2 ** 3) - l2fEnabled (2 ** 4) - ipinipEnabled (2 ** 5) - vRouterEnabled (2 ** 6) - aodiEnabled (2 ** 7) - maddModemEnabled (2 ** 8) - madd96DevicesEnabled (2 ** 9) - maddHdlcEnabled (2 ** 10) - v110Enabled (2 ** 11) - sdtnEnabled (2 ** 12) - restrictDSLTermEnabled (2 ** 13) - megamaxEnabled (2 ** 14) - maxtapEnabled (2 ** 15) - phs21Enabled (2 ** 16) - atmSvcEnabled (2 ** 17) - frVcEnabled (2 ** 18) - networkManagementVoipEnabled (2 ** 19) - networkManagementPlusEnabled (2 ** 20) - networkManagementPlusVoipEnabled |
| INT sysSPROMSerialNumber | 1.3.6.1.4.1.529.9.11.1 | INTEGER | read-only | The serial number as stored in the security PROM. The same value is also returned as part of sysName. |
| systemStatusGroup | 1.3.6.1.4.1.529.9 | |||
| terminator | 1.3.6.1.4.1.529.1.2.11 | |||
| voipGroup | 1.3.6.1.4.1.529.28 | |||
| wanDialoutPkt | 1.3.6.1.4.1.529.17 |
RFC description
Ascend Communications enterprise MIB defining OID structure and management objects for Ascend networking equipment (legacy vendor).
Start monitoring Ascend Communications MAX and Pipeline WAN access/dial-up equipment (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.