ALCATEL-IND1-PORT-MIB

All MIBs › ALCATEL-IND1-PORT-MIB

Organization: Alcatel-Lucent

Last Updated: 2013-11-22

Category: Network Interfaces, Vendor: Alcatel-Lucent

Description: Alcatel OmniSwitch port management MIB for configuring speed, duplex, flow control, and physical port parameters.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ALCATEL-IND1-PORT-MIB?

ALCATEL-IND1-PORT-MIB is an Alcatel-Lucent OmniSwitch proprietary MIB for Ethernet and Fibre Channel switching module port configuration, covering speed, duplex, flow control, and other physical-port parameters. Beyond basic configuration it includes Digital Diagnostics Monitoring (DDM) objects that read transceiver temperature and configurable warning thresholds, dying-gasp objects reporting chassis ID and power supply type at the moment of a power loss, and driver-level trap-drop counters. This gives it strong hardware-health relevance: ddmTemperature and ddmTempLowWarning let operators detect an SFP/transceiver overheating or running outside its safe operating range, while dying-gasp objects provide last-gasp notification of power supply failure. It layers vendor-specific transceiver and power-event monitoring on top of the standard IF-MIB rather than replacing physical/optical interface management wholesale. It is deployed on OmniSwitch chassis with pluggable optics, where transceiver health and power-loss detection are operationally important. Engineers can download the ALCATEL-IND1-PORT-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ALCATEL-IND1-PORT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Alcatel-Lucent OmniSwitch switches with pluggable optics

Monitoring Examples

An operator would poll ddmInfoTable/ddmInfoEntry for ddmTemperature on each transceiver and compare it against ddmTempLowWarning to catch an optic running outside its rated temperature range before it fails outright. Watching esmDrvTrapDrops would reveal whether the switch's SNMP trap subsystem is dropping notifications due to overload, meaning other alerts could be silently lost. A dying-gasp trap carrying alaDyingGaspChassisId and alaDyingGaspPowerSupplyType would immediately flag which chassis and power supply lost power, useful for correlating a site-wide outage.

What Can Be Monitored

transceiver (DDM) temperature
DDM warning thresholds
dying-gasp chassis/power-supply identification
trap-drop counters
port speed/duplex/flow-control configuration

Imported Objects

From ALCATEL-IND1-BASE

softentIND1Port

OBJECT-IDENTITY

From IF-MIB

InterfaceIndex
ifEntry	OBJECT-TYPE
ifInErrors	OBJECT-TYPE
ifIndex	OBJECT-TYPE
ifOutErrors	OBJECT-TYPE

From SNMP-FRAMEWORK-MIB

SnmpAdminString

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Integer32
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks

From SNMPv2-TC

DateAndTime
DisplayString
MacAddress
RowStatus
TEXTUAL-CONVENTION

How to Use in IPNetwork Monitor

Example using alcetherStatsCRCAlignErrors OID:

Select an Alcatel-Lucent Enterprise OmniSwitch switch as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type alcetherStatsCRCAlignErrors into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The total number of packets received with a length between 64 and 1518 octets that had either a bad FCS with an integral number of octets (FCS Error) or a non-integral number of octets (Alignment Error). On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases between polls, since a rising count of errors, failures, or discards often points to a real underlying problem. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
I32 alaDyingGaspChassisId	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.6.1	Integer32	accessible-for-notify	This object specifies the chassis id of the chassis whose NI is going down.
INT alaDyingGaspPowerSupplyType	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.6.2	INTEGER	accessible-for-notify	This object specifies the type of the power supply.
DAT alaDyingGaspTime	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.6.3	DateAndTime	accessible-for-notify	This object specifies the time of power failure.
NTF alaDyingGaspTrap	1.3.6.1.4.1.6486.801.1.2.1.5.1.0.9			Dying Gasp trap.
alaLFPConfigEntry	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.5.1		not-accessible	A list of Link Fault Propagation port and port type of each LFP group
alaLFPConfigMIBGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.17			A collection of objects to configure a port and port type for a Link Fault Propagation Group.
NUM alaLFPConfigPort	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.5.1.1	InterfaceIndex	accessible-for-notify	Indicates ifindex of source/destination port for a LFP Group.
INT alaLFPConfigPortType	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.5.1.2	INTEGER	read-create	Indicates the type of port, (1) means the port is destination port and (2) means the port is a destination port for a LFP Group.
ROW alaLFPConfigRowStatus	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.5.1.3	RowStatus	read-create	Row Status for initiating a MIB retrieval request.
alaLFPConfigTable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.5		not-accessible	A list of Link Fault Propagation port and port type of each LFP group
INT alaLFPGroupAdminStatus	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.4.1.2	INTEGER	read-create	Indicates the admin status of the group. disable(2) means link fault propagation, is disbaled. enable(1) means link fault propagation is enabled
alaLFPGroupEntry	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.4.1		not-accessible	The list of Link Fault Propagation group id and status for each group
I32 alaLFPGroupId	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.4.1.1	Integer32	accessible-for-notify	Indicates the unique group id for Link Fault Propagation (LFP).
alaLFPGroupMIBGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.16			A collection of objects to configure Link Fault Propagation Group, Wait to shutdown timer and admin staus of group.
INT alaLFPGroupOperStatus	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.4.1.3	INTEGER	read-only	Indicates the operational status of the group. down(2) means all the source ports are down, up(1) means atleast one source port in the group is up.
ROW alaLFPGroupRowStatus	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.4.1.5	RowStatus	read-create	Row Status for initiating a MIB retrieval request.
alaLFPGroupTable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.4		not-accessible	A list of Link Fault Propagation Grooups and their status
I32 alaLFPGroupWaitToShutdown	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.4.1.4	Integer32	read-create	0 - Disable wait to shutdown timer 5 - 300 - after expiry of this timer all destination ports will be shutdown
alaLinkMonConfigEntry	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2.1		not-accessible	A collection of Link Monitoring configurations kept for a particular Ethernet interface.
alaLinkMonConfigMIBGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.14			A collection of objects to support the Link Monitoring Configurations on the ports.
alaLinkMonConfigTable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2		not-accessible	A list of Link Monitoring Configuration Parameters
I32 alaLinkMonLinkErrorThreshold	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2.1.4	Integer32	read-write	Indicates the number of link errors allowed on Rx for the specified port during the time window before the port is shutdown. The errors are the MAC errors that include CRC, lost frames, error frames, alignment frames.
I32 alaLinkMonLinkFlapThreshold	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2.1.3	Integer32	read-write	Indicaes the number of link flaps allowed for the specified port during the time window before the port is shutdown.
INT alaLinkMonStatsClearStats	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.1	INTEGER	read-write	Used to Clear all Statistics counters. The value reset (1) indicates that Link Monitoring shuold all statistic counters related to the particular port. By default, this object contains zero value.
C64 alaLinkMonStatsCurrentAlignErrors	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.7	Counter64	read-only	Indicates the number of Rx alignment frames in the current time window.
C64 alaLinkMonStatsCurrentCRCErrors	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.5	Counter64	read-only	Indicates the number of CRC errors in the current time window.
C64 alaLinkMonStatsCurrentErrorFrames	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.4	Counter64	read-only	Indicates the number of error frames in the current time window.
C64 alaLinkMonStatsCurrentLinkErrors	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.8	Counter64	read-only	Indicates the sum of all the MAC Errors within the current time window. i.e., the sum of alaLinkMonStatsCurrentErrorFrames, alaLinkMonStatsCurrentCRCErrors, alaLinkMonCurrentLosFrames, alaLinkMonStatsCurrentAlignErrors.
C64 alaLinkMonStatsCurrentLinkFlaps	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.3	Counter64	read-only	Indicates the number of Link flaps in the current time window.
C64 alaLinkMonStatsCurrentLostFrames	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.6	Counter64	read-only	Indicates the number of Rx Lost frames in the current time window.
alaLinkMonStatsEntry	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1		not-accessible	A collection of Link Monitoring statistics for a particular Ethernet interface.
alaLinkMonStatsMIBGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.15			A collection of objects to provide all the statistics related to the Link Monitoring on the ports.
INT alaLinkMonStatsPortState	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.2	INTEGER	read-only	Indicates the status of the port. up(1) means the port is physically up, down(2) means the port is physically down, shutdown(3) means the interface is shutdown because of excessive link flaps or link errors.
alaLinkMonStatsTable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3		not-accessible	A list of Link Monitoring Statistics
C64 alaLinkMonStatsTotalLinkErrors	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.10	Counter64	read-only	Indicates the total number of link errors across all the time windows.
C64 alaLinkMonStatsTotalLinkFlaps	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.3.1.9	Counter64	read-only	Indicates the total number of link flaps across all the time windows.
INT alaLinkMonStatus	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2.1.1	INTEGER	read-write	Allows the user to enable or disable Link Monitoring on the port.
I32 alaLinkMonTimeWindow	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2.1.2	Integer32	read-write	Indicates the number of seconds the Link will be monitored for a port.
I32 alaLinkMonWaitToRestoreTimer	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2.1.5	Integer32	read-write	Indicates the number of seconds after which the link up event is notified to other applications. The timer is started whenever a Link Up is detected on a port being monitored.
I32 alaLinkMonWaitToShutdownTimer	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.2.1.6	Integer32	read-write	Indicates the number of milli seconds after which the link down event is notified to other applications. The timer is started whenever a Link down is detected on a port being monitored.
alcatelIND1PortMIB	1.3.6.1.4.1.6486.801.1.2.1.5.1			This module describes an authoritative enterprise-specific Simple Network Management Protocol (SNMP) Management Information Base (MIB): This group contains the configuration information data for the Ethernet and Fiber Channel Switching Module. The right to make changes in specification and other information contained in this document without prior notice is reserved. No liability shall be assumed for any incidental, indirect, special, or consequential damages whatsoever arising from or related to this document or the information contained herein. Vendors, end-users, and other interested parties are granted non-exclusive license to use this specification in connection with management of the products for which it is intended to be used. Copyright (C) 1995-2013 Alcatel-Lucent ALL RIGHTS RESERVED WORLDWIDE
alcatelIND1PortMIBCompliances	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.1
alcatelIND1PortMIBConformance	1.3.6.1.4.1.6486.801.1.2.1.5.1.2
alcatelIND1PortMIBGroups	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2
alcatelIND1PortMIBObjects	1.3.6.1.4.1.6486.801.1.2.1.5.1.1
alcatelIND1PortNotifications	1.3.6.1.4.1.6486.801.1.2.1.5.1.0
INT alcetherClearStats	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.1	INTEGER	read-write	Used to Clear all Statistics counters. By default, this object contains zero value.
TIK alcetherLastClearStats	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.2	TimeTicks	read-only	The value of SysUpTime at the time of all the statistics counters are cleared. By default, this object contains a zero value.
alcEtherStatsCompliance	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.1.2			The compliance statement for the Statistics of the Ethernet ports.
C64 alcetherStatsCRCAlignErrorsEx	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.3	Counter64	read-only	The total number of packets received that had a length (excluding framing bits, but including FCS octets) of between 64 and 1518 octets, inclusive, but but had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error).
alcetherStatsEntry	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1		not-accessible	A collection of statistics kept for a particular Ethernet interface. As an example, an instance of the etherStatsPkts object might be named alcetherStatsPkts.1
alcEtherStatsMIBGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.3			A collection of objects to provide all the statistics related to the Ethernet and GigaEthernert ports.
C64 alcetherStatsPkts1024to1518Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.15	Counter64	read-only	The total number of packets (including bad packets) received that were between 1024 and 1518 octets in length inclusive (excluding framing bits but including FCS octets). For both Ethernet and GigaEthernet.
C64 alcetherStatsPkts128to255Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.12	Counter64	read-only	The total number of packets (including bad packets) received that were between 128 and 255 octets in length inclusive (excluding framing bits but including FCS octets).
C64 alcetherStatsPkts1519to2047Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.18	Counter64	read-only	The total number of frames(including error packets) received that were between 1519 and 2047 bytes in length inclusive (excluding framing bits but including FCS bytes).
C64 alcetherStatsPkts2048to4095Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.19	Counter64	read-only	The total number of frames(including error packets) received that were between 2048 and 4095 bytes in length inclusive (excluding framing bits but including FCS bytes).
C64 alcetherStatsPkts256to511Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.13	Counter64	read-only	The total number of packets (including bad packets) received that were between 256 and 511 octets in length inclusive (excluding framing bits but including FCS octets).
C64 alcetherStatsPkts4096Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.20	Counter64	read-only	The total number of frames(including error packets) received that were greater than or equal to 4096 bytes in length inclusive (excluding framing bits but including FCS bytes).
C64 alcetherStatsPkts512to1023Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.14	Counter64	read-only	The total number of packets (including bad packets) received that were between 512 and 1023 octets in length inclusive (excluding framing bits but including FCS octets).
C64 alcetherStatsPkts64Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.10	Counter64	read-only	The total number of packets (including bad packets) received that were 64 octets in length (excluding framing bits but including FCS octets).
C64 alcetherStatsPkts65to127Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.11	Counter64	read-only	The total number of packets (including bad packets) received that were between 65 and 127 octets in length inclusive (excluding framing bits but including FCS octets).
C64 alcetherStatsRxCodeErrPkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.27	Counter64	read-only	The total number of frames for which one or more nibbles were signaled as errors during reception of the frame.
C64 alcetherStatsRxCollisions	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.8	Counter64	read-only	The best estimate of the total number of collisions on this Ethernet segment (in reception). Only for Ethernet Interfaces. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and section 10.3.1.3 (10BASE-2) of IEEE standard 802.3 states that a station must detect a collision, in the receive mode, if three or more stations are transmitting simultaneously. A repeater port must detect a collision when two or more stations are transmitting simultaneously. Thus a probe placed on a repeater port could record more collisions than a probe connected to a station on the same segment would. Probe location plays a much smaller role when considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE standard 802.3 defines a collision as the simultaneous presence of signals on the DO and RD circuits (transmitting and receiving at the same time). A 10BASE-T station can only detect collisions when it is transmitting. Thus probes placed on a station and a repeater, should report the same number of collisions. Note also that an RMON probe inside a repeater should ideally report collisions between the repeater and one or more other hosts (transmit collisions as defined by IEEE 802.3k) plus receiver collisions observed on any coax segments to which the repeater is connected.
C64 alcetherStatsRxControlPkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.25	Counter64	read-only	The total number of frames that were recognized as control frames.
C64 alcetherStatsRxDribbleNibblePkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.22	Counter64	read-only	The total number of frames for which a dribble nibble has been received and CRC is correct.
C64 alcetherStatsRxDvEventPkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.28	Counter64	read-only	The total number of frames for which a RX_DV event (packet not too long enough to be valid packet) has been seen before the correct frame.
C64 alcetherStatsRxGiantPkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.21	Counter64	read-only	The total number of frames that are greater than the specified Max length value, with a valid CRC, dropped because too long.
C64 alcetherStatsRxJabbers	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.7	Counter64	read-only	The total number of packets received that were longer than 1518 octets (excluding framing bits, but including FCS octets), and had either a bad Frame Check Sequence (FCS) with an integral number of octets (FCS Error) or a bad FCS with a non-integral number of octets (Alignment Error). Note that this definition of jabber is different than the definition in IEEE-802.3 section 8.2.1.5 (10BASE5) and section 10.3.1.4 (10BASE2). These documents define jabber as the condition where any packet exceeds 20 ms. The allowed range to detect jabber is between 20 ms and 150 ms.
C64 alcetherStatsRxLenChkErrPkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.26	Counter64	read-only	The total number of frames for which the frame length field value in the Type/Length field does not match the actual data bytes length and is NOT a type field.
C64 alcetherStatsRxLongEventPkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.23	Counter64	read-only	The total number of frames for which the Carrier sense exceeds 50000 bit times for 10 Mbits/sec or 80000 bit times for 100 Mbits/sec.
C64 alcetherStatsRxPrevPktDropped	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.29	Counter64	read-only	The total number of frames for which a packet has been dropped (because of too small IFG) before the correct frame.
C64 alcetherStatsRxUndersizePkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.4	Counter64	read-only	The total number of packets received that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
C64 alcetherStatsRxVlanTagPkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.24	Counter64	read-only	The total number of frames for which Type/Length field contains the VLAN protocol identifier (0x8100).
alcetherStatsTable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2		not-accessible	A list of Ethernet statistics entries.
C64 alcetherStatsTx1024to1518Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.35	Counter64	read-only	The total number of transmitted frames that were between 1024 and 1518 bytes in length inclusive (excluding framing bits but including FCS bytes).
C64 alcetherStatsTx128to255Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.32	Counter64	read-only	The total number of transmitted frames that were between 128 and 255 bytes in length inclusive (excluding framing bits but including FCS bytes).
C64 alcetherStatsTx1519to2047Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.36	Counter64	read-only	The total number of transmitted frames that were between 1519 and 2047 bytes in length inclusive (excluding framing bits but including FCS bytes).
C64 alcetherStatsTx2048to4095Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.37	Counter64	read-only	The total number of transmitted frames that were between 2048 and 4095 bytes in length inclusive (excluding framing bits but including FCS bytes).
C64 alcetherStatsTx256to511Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.33	Counter64	read-only	The total number of transmitted frames that were between 256 and 511 bytes in length inclusive (excluding framing bits but including FCS bytes).
C64 alcetherStatsTx4096Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.38	Counter64	read-only	The total number of transmitted frames that were greater than or equal to 4096 bytes in length and less than Max frame length (excluding framing bits but including FCS bytes).
C64 alcetherStatsTx512to1023Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.34	Counter64	read-only	The total number of transmitted frames that were between 512 and 1023 bytes in length inclusive (excluding framing bits but including FCS bytes).
C64 alcetherStatsTx64Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.30	Counter64	read-only	The total number of transmitted frames of 64 bytes.
C64 alcetherStatsTx65to127Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.31	Counter64	read-only	The total number of transmitted frames that were between 65 and 127 bytes in length inclusive (excluding framing bits but including FCS bytes).
C64 alcetherStatsTxCollisions	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.9	Counter64	read-only	The best estimate of the total number of collisions on this Ethernet segment (in transmition). Only for Ethernet Interfaces. The value returned will depend on the location of the RMON probe. Section 8.2.1.3 (10BASE-5) and section 10.3.1.3 (10BASE-2) of IEEE standard 802.3 states that a station must detect a collision, in the receive mode, if three or more stations are transmitting simultaneously. A repeater port must detect a collision when two or more stations are transmitting simultaneously. Thus a probe placed on a repeater port could record more collisions than a probe connected to a station on the same segment would. Probe location plays a much smaller role when considering 10BASE-T. 14.2.1.4 (10BASE-T) of IEEE standard 802.3 defines a collision as the simultaneous presence of signals on the DO and RD circuits (transmitting and receiving at the same time). A 10BASE-T station can only detect collisions when it is transmitting. Thus probes placed on a station and a repeater, should report the same number of collisions. Note also that an RMON probe inside a repeater should ideally report collisions between the repeater and one or more other hosts (transmit collisions as defined by IEEE 802.3k) plus receiver collisions observed on any coax segments to which the repeater is connected.
C64 alcetherStatsTxControlPkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.41	Counter64	read-only	The total number of transmitted frames that were recognised as control frames.
C64 alcetherStatsTxExcDeferPkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.45	Counter64	read-only	The total number of frames that were deferred in excess of 6071 nibble-times in 100 Mbps, 24287 bit-times in 10 Mbps mode. These frames are dropped.(This stat is only in case of Half duplex and excessive defer bit reset).
C64 alcetherStatsTxLatePkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.42	Counter64	read-only	The total number of late collisions that occured beyond the collision window.
C64 alcetherStatsTxLenChkErrPkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.44	Counter64	read-only	The total number of transmitted frames for which the frame length field value in the Type/Length field does not match the actual data bytes length and is NOT a Type field.
C64 alcetherStatsTxOversizePkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.6	Counter64	read-only	The total number of packets transmitted that were longer than 1518 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
C64 alcetherStatsTxRetryCount	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.39	Counter64	read-only	The total number of collisions that the frames faced during transmission attempts.
C64 alcetherStatsTxTotalBytesOnWire	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.43	Counter64	read-only	The total number of bytes transmitted on wire, including all bytes from collided attempts.
C64 alcetherStatsTxUndersizePkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.5	Counter64	read-only	The total number of packets transmitted that were less than 64 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
C64 alcetherStatsTxVlanTagPkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.40	Counter64	read-only	The total number of transmitted frames for which Type/Length field contains the VLAN protocol identifier (0x8100).
INT alcfcClearStats	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.1	INTEGER	read-write	Used to Clear all Statistics counters. By default, this object contains zero value.
TIK alcfcLastClearStats	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.2	TimeTicks	read-only	The value of SysUpTime at the time of all the statistics counters are cleared. By default, this object contains a zero value.
C64 alcfcStatsDelimiterErrors	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.16	Counter64	read-only	The number of invalid delimiters received
C64 alcfcStatsEncodingDisparityErrors	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.17	Counter64	read-only	The number of detected running disparity at 10b/8b level.
alcfcStatsEntry	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1		not-accessible	A collection of statistics kept for a particular Fiber Channel interface. As an example, an instance of the fcStatsPkts object might be named alcfcStatsPkts.1
C64 alcfcStatsFrameTooLongs	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.15	Counter64	read-only	The number of frames received at this port for which the frame length was greater than what was agreed to in FLOGI/PLOGI.
C64 alcfcStatsInvalidCRCs	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.13	Counter64	read-only	The number of frames received with an invalid CRC.
C64 alcfcStatsInvalidOrderedSets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.14	Counter64	read-only	The number of invalid ordered sets received at this port.
C64 alcfcStatsInvalidTxWords	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.12	Counter64	read-only	The number of invalid transmission words. This includes invalid ordered sets and invalid data words.
C64 alcfcStatsLinkFailures	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.8	Counter64	read-only	The number of link failures.
C64 alcfcStatsLossofSignals	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.10	Counter64	read-only	The number of loss of signals detected.
C64 alcfcStatsLossofSynchs	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.9	Counter64	read-only	The number of loss of word-sync detected.
C64 alcfcStatsOtherErrors	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.18	Counter64	read-only	The number of errors detected but not counted by any other error counter. This only includes RX frames drops due to zero RX BBCredits
C64 alcfcStatsPrimSeqProtocolErrors	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.11	Counter64	read-only	The number of primitive sequence protocol errors detected.
C64 alcfcStatsRxBBCreditZeros	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.7	Counter64	read-only	The number of times RX BBCredit drops to zero.
C64 alcfcStatsRxUndersizePkts	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.3	Counter64	read-only	The total number of packets received that were less than 36 octets long (excluding framing bits, but including FCS octets) and were otherwise well formed.
alcfcStatsTable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7		not-accessible	A list of Fiber Channel statistics entries.
C64 alcfcStatsTxBBCreditZeros	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.7.1.6	Counter64	read-only	The number of transitions in/out of the buffer-to-buffer credit zero state.
alcPortNotificationGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.4			The Port MIB Notification Group.
csmConfTrap	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.6
csmConfTrapGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.18			A collection of objects for chassis supervision traps
INT ddmConfig	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.4.1	INTEGER	read-write	This object enables/disables DDM software feature in the system.
ddmConfigGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.7			A collection of objects to allow configuration of DDM and DDM traps.
ddmConfiguration	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.4
NTF ddmCurrentThresholdViolated	1.3.6.1.4.1.6486.801.1.2.1.5.1.0.4			This object notifies management station if an SFP/XFP/SFP+ Tx bias current has crossed any threshold or reverted from previous threshold violation for a port represented by ifIndex. It also provides the current realtime value of SFP/XFP/SFP+ Tx bias current.
ddmInfoEntry	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1		not-accessible	Each row represents a particular SFP/XFP that supports Digital Diagnostic Monitoring. Entries are created and deleted internally by the system.
ddmInfoGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.6			A collection of objects to provide digital diagnostics information related to SFPs, XFPs, and SFP+s.
ddmInfoTable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5		not-accessible	The ddmInfoTable has an entry for each SFP/XFP in the system that supports Digital Diagnostic Monitoring (DDM). The table is indexed by ifIndex. Each row in this table is dynamically added and removed internally by the system based on the presence or absence of DDM capable SFP/XFP components.
ddmNotificationsGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.8			A collection of notifications used to indicate DDM threshold violations.
INT ddmNotificationType	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.4.3	INTEGER	accessible-for-notify	This object defines the trap type for monitored DDM parameters.
I32 ddmPortChannel	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.1	Integer32	read-only	The channel number of the data that is being read. In the case of a QSFP there will be 4 10 gigabyte channels, for SFP/XFP there will only be one.
ddmPortInfoEntry	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1		not-accessible	Each row represents a particular SFP/XFP that supports Digital Diagnostic Monitoring. Entries are created and deleted internally by the system.
ddmPortInfoGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.13			A collection of objects to provide digital diagnostics information related to SFPs, XFPs, and SFP+s.
ddmPortInfoTable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6		not-accessible	The ddmPortInfoTable has an entry for each SFP/XFP in the system that supports Digital Diagnostic Monitoring (DDM). The table is indexed by ifIndex and port channel. Each row in this table is dynamically added and removed internally by the system based on the presence or absence of DDM capable SFP/XFP components.
I32 ddmPortRxOpticalPower	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.22	Integer32	read-only	The value of ddmRxOpticalPower indicates the current Received Optical Power of the SFP/XFP in 1000s of dBm. A value of -200000 indicates this object is not applicable.
I32 ddmPortRxOpticalPowerHiAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.26	Integer32	read-only	The value of ddmRxOpticalPowerHiAlarm indicates the Received Optical Power of the SFP/XFP in 1000s of dBm that triggers a hi-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmPortRxOpticalPowerHiWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.25	Integer32	read-only	The value of ddmRxOpticalPowerHiWarning indicates the Received Optical Power of the SFP/XFP in 1000s of dBm that triggers a hi-warning. A value of -200000 indicates this object is not applicable.
I32 ddmPortRxOpticalPowerLowAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.24	Integer32	read-only	The value of ddmRxOpticalPowerLowAlarm indicates the Received Optical Power of the SFP/XFP in 1000s of dBm that triggers a low-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmPortRxOpticalPowerLowWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.23	Integer32	read-only	The value of ddmRxOpticalPowerLowWarning indicates the Received Optical Power of the SFP/XFP in 1000s of dBm that triggers a low-warning. A value of -200000 indicates this object is not applicable.
I32 ddmPortSupplyVoltage	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.7	Integer32	read-only	The value of ddmSupplyVoltage indicates the current supply voltage of the SFP/XFP in 1000s of Volts (V). A value of -200000 indicates this object is not applicable.
I32 ddmPortSupplyVoltageHiAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.11	Integer32	read-only	The value of ddmSupplyVoltageHiAlarm indicates the supply voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmPortSupplyVoltageHiWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.10	Integer32	read-only	The value of ddmSupplyVoltageHiWarning indicates the supply voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-warning. A value of -200000 indicates this object is not applicable.
I32 ddmPortSupplyVoltageLowAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.9	Integer32	read-only	The value of ddmSupplyVoltageLowAlarm indicates the supply voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmPortSupplyVoltageLowWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.8	Integer32	read-only	The value of ddmSupplyVoltageLowWarning indicates the supply voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-warning. A value of -200000 indicates this object is not applicable.
I32 ddmPortTemperature	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.2	Integer32	read-only	The value of ddmTemperature indicates the current temperature of the SFP/XFP in 1000s of degrees Celsius. A value of -200000 indicates this object is not applicable.
I32 ddmPortTempHiAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.6	Integer32	read-only	The value of ddmTempHiAlarm indicates the temperature of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmPortTempHiWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.5	Integer32	read-only	The value of ddmTempHiWarning indicates the temperature of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-warning. A value of -200000 indicates this object is not applicable.
I32 ddmPortTempLowAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.4	Integer32	read-only	The value of ddmTempLowAlarm indicates the temperature of the SFP/XFP in 1000s of degrees Celsius that triggers a low-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmPortTempLowWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.3	Integer32	read-only	The value of ddmTempLowWarning indicates the temperature of the SFP/XFP in 1000s of degrees Celsius that triggers a low-warning. A value of -200000 indicates this object is not applicable.
I32 ddmPortTxBiasCurrent	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.12	Integer32	read-only	The value of ddmTxBiasCurrent indicates the current Transmit Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA). A value of -200000 indicates this object is not applicable.
I32 ddmPortTxBiasCurrentHiAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.16	Integer32	read-only	The value of ddmTxBiasCurrentHiAlarm indicates the Transmit Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a hi-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmPortTxBiasCurrentHiWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.15	Integer32	read-only	The value of ddmTxBiasCurrentHiWarning indicates the Transmit Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a hi-warning. A value of -200000 indicates this object is not applicable.
I32 ddmPortTxBiasCurrentLowAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.14	Integer32	read-only	The value of ddmTxBiasCurrentLowAlarm indicates the Transmit Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a low-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmPortTxBiasCurrentLowWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.13	Integer32	read-only	The value of ddmTxBiasCurrentLowWarning indicates the Transmit Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a low-warning. A value of -200000 indicates this object is not applicable.
I32 ddmPortTxOutputPower	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.17	Integer32	read-only	The value of ddmTxOutputPower indicates the current Output Power of the SFP/XFP in 1000s of dBm. A value of -200000 indicates this object is not applicable.
I32 ddmPortTxOutputPowerHiAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.21	Integer32	read-only	The value of ddmTxOutputPowerHiAlarm indicates the Output Power of the SFP/XFP in 1000s of dBm that triggers a hi-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmPortTxOutputPowerHiWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.20	Integer32	read-only	The value of ddmTxOutputPowerHiWarning indicates the Output Power of the SFP/XFP in 1000s of dBm that triggers a hi-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmPortTxOutputPowerLowAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.19	Integer32	read-only	The value of ddmTxOutputPowerLowAlarm indicates the Output Power of the SFP/XFP in 1000s of dBm that triggers a low-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmPortTxOutputPowerLowWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.6.1.18	Integer32	read-only	The value of ddmTxOutputPowerLowWarning indicates the Output Power of the SFP/XFP in 1000s of dBm that triggers a low-warning. A value of -200000 indicates this object is not applicable.
I32 ddmRxOpticalPower	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.21	Integer32	read-only	The value of ddmRxOpticalPower indicates the current Received Optical Power of the SFP/XFP in 1000s of dBm. A value of -200000 indicates this object is not applicable.
I32 ddmRxOpticalPowerHiAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.25	Integer32	read-only	The value of ddmRxOpticalPowerHiAlarm indicates the Received Optical Power of the SFP/XFP in 1000s of dBm that triggers a hi-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmRxOpticalPowerHiWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.24	Integer32	read-only	The value of ddmRxOpticalPowerHiWarning indicates the Received Optical Power of the SFP/XFP in 1000s of dBm that triggers a hi-warning. A value of -200000 indicates this object is not applicable.
I32 ddmRxOpticalPowerLowAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.23	Integer32	read-only	The value of ddmRxOpticalPowerLowAlarm indicates the Received Optical Power of the SFP/XFP in 1000s of dBm that triggers a low-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmRxOpticalPowerLowWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.22	Integer32	read-only	The value of ddmRxOpticalPowerLowWarning indicates the Received Optical Power of the SFP/XFP in 1000s of dBm that triggers a low-warning. A value of -200000 indicates this object is not applicable.
NTF ddmRxPowerThresholdViolated	1.3.6.1.4.1.6486.801.1.2.1.5.1.0.6			This object notifies management station if an SFP/XFP/SFP+ Rx optical power has crossed any threshold or reverted from previous threshold violation for a port represented by ifIndex. It also provides the current realtime value of SFP/XFP/SFP+ Rx optical power.
I32 ddmSupplyVoltage	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.6	Integer32	read-only	The value of ddmSupplyVoltage indicates the current supply voltage of the SFP/XFP in 1000s of Volts (V). A value of -200000 indicates this object is not applicable.
I32 ddmSupplyVoltageHiAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.10	Integer32	read-only	The value of ddmSupplyVoltageHiAlarm indicates the supply voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmSupplyVoltageHiWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.9	Integer32	read-only	The value of ddmSupplyVoltageHiWarning indicates the supply voltage of the SFP/XFP in 1000s of Volts (V) that triggers a hi-warning. A value of -200000 indicates this object is not applicable.
I32 ddmSupplyVoltageLowAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.8	Integer32	read-only	The value of ddmSupplyVoltageLowAlarm indicates the supply voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmSupplyVoltageLowWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.7	Integer32	read-only	The value of ddmSupplyVoltageLowWarning indicates the supply voltage of the SFP/XFP in 1000s of Volts (V) that triggers a low-warning. A value of -200000 indicates this object is not applicable.
I32 ddmTemperature	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.1	Integer32	read-only	The value of ddmTemperature indicates the current temperature of the SFP/XFP in 1000s of degrees Celsius. A value of -200000 indicates this object is not applicable.
NTF ddmTemperatureThresholdViolated	1.3.6.1.4.1.6486.801.1.2.1.5.1.0.2			This object notifies management station if an SFP/XFP/SFP+ temperature has crossed any threshold or reverted from previous threshold violation for a port represented by ifIndex. It also provides the current realtime value of SFP/XFP/SFP+ temperature.
I32 ddmTempHiAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.5	Integer32	read-only	The value of ddmTempHiAlarm indicates the temperature of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmTempHiWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.4	Integer32	read-only	The value of ddmTempHiWarning indicates the temperature of the SFP/XFP in 1000s of degrees Celsius that triggers a hi-warning. A value of -200000 indicates this object is not applicable.
I32 ddmTempLowAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.3	Integer32	read-only	The value of ddmTempLowAlarm indicates the temperature of the SFP/XFP in 1000s of degrees Celsius that triggers a low-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmTempLowWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.2	Integer32	read-only	The value of ddmTempLowWarning indicates the temperature of the SFP/XFP in 1000s of degrees Celsius that triggers a low-warning. A value of -200000 indicates this object is not applicable.
INT ddmTrapConfig	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.4.2	INTEGER	read-write	This objects enables/disables traps for DDM warning/alarm threshold violations.
I32 ddmTxBiasCurrent	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.11	Integer32	read-only	The value of ddmTxBiasCurrent indicates the current Transmit Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA). A value of -200000 indicates this object is not applicable.
I32 ddmTxBiasCurrentHiAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.15	Integer32	read-only	The value of ddmTxBiasCurrentHiAlarm indicates the Transmit Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a hi-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmTxBiasCurrentHiWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.14	Integer32	read-only	The value of ddmTxBiasCurrentHiWarning indicates the Transmit Bias Current of the SFP/XFP in 1000s milli-Amperes (mA) that triggers a hi-warning. A value of -200000 indicates this object is not applicable.
I32 ddmTxBiasCurrentLowAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.13	Integer32	read-only	The value of ddmTxBiasCurrentLowAlarm indicates the Transmit Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a low-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmTxBiasCurrentLowWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.12	Integer32	read-only	The value of ddmTxBiasCurrentLowWarning indicates the Transmit Bias Current of the SFP/XFP in 1000s of milli-Amperes (mA) that triggers a low-warning. A value of -200000 indicates this object is not applicable.
I32 ddmTxOutputPower	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.16	Integer32	read-only	The value of ddmTxOutputPower indicates the current Output Power of the SFP/XFP in 1000s of dBm. A value of -200000 indicates this object is not applicable.
I32 ddmTxOutputPowerHiAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.20	Integer32	read-only	The value of ddmTxOutputPowerHiAlarm indicates the Output Power of the SFP/XFP in 1000s of dBm that triggers a hi-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmTxOutputPowerHiWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.19	Integer32	read-only	The value of ddmTxOutputPowerHiWarning indicates the Output Power of the SFP/XFP in 1000s of dBm that triggers a hi-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmTxOutputPowerLowAlarm	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.18	Integer32	read-only	The value of ddmTxOutputPowerLowAlarm indicates the Output Power of the SFP/XFP in 1000s of dBm that triggers a low-alarm. A value of -200000 indicates this object is not applicable.
I32 ddmTxOutputPowerLowWarning	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.5.1.17	Integer32	read-only	The value of ddmTxOutputPowerLowWarning indicates the Output Power of the SFP/XFP in 1000s of dBm that triggers a low-warning. A value of -200000 indicates this object is not applicable.
NTF ddmTxPowerThresholdViolated	1.3.6.1.4.1.6486.801.1.2.1.5.1.0.5			This object notifies management station if an SFP/XFP/SFP+ Tx output power has crossed any threshold or reverted from previous threshold violation for a port represented by ifIndex. It also provides the current realtime value of SFP/XFP/SFP+ Tx output power.
NTF ddmVoltageThresholdViolated	1.3.6.1.4.1.6486.801.1.2.1.5.1.0.3			This object notifies management station if an SFP/XFP/SFP+ supply voltage has crossed any threshold or reverted from previous threshold violation for a port represented by ifIndex. It also provides the current realtime value of SFP/XFP/SFP+ supply voltage.
esmConfEntry	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1		not-accessible	A ESM Physical Port entry.
esmConfEntryGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.11			A list of ESM Physical Port instances.
esmConfMIBGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.1			A collection of objects to support the management of global configuration parameters of the Ethernet ports.
esmConfPortCompliance	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.1.1			The compliance statement for the configuration of Ethernet ports.
esmConfTable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1		not-accessible	A list of ESM Physical Port instances.
esmConfTrap	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.1
esmConfTrapGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.9			Partitioned port (separated due to errors).
esmDetectedConfMIBGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.2			A collection of objects to support the Detected configuration parameters of the Ethernet ports.
I32 esmDrvTrapDrops	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.1.1	Integer32	read-only	Partitioned port (separated due to errors).
NTF esmDrvTrapDropsLink	1.3.6.1.4.1.6486.801.1.2.1.5.1.0.1			When the Ethernet code drops the link because of excessive errors, a Trap is sent.
esmHybridConfEntry	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3.1		not-accessible	A ESM Physical Port entry.
esmHybridConfEntryGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.10			A list of inactive hybrid port instances.
esmHybridConfTable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3		not-accessible	A list of inactive hybrid port instances.
INT esmHybridPortCfgAutoNegotiation	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3.1.3	INTEGER	read-write	Allow the user to enable or disable the port auto negotiation.
INT esmHybridPortCfgCrossover	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3.1.4	INTEGER	read-write	Allow the user to configure port crossover.
INT esmHybridPortCfgDuplexMode	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3.1.2	INTEGER	read-write	The configured port duplex mode of this ESM port. Note: GigaEthernet support only full-duplex.
INT esmHybridPortCfgFlow	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3.1.5	INTEGER	read-write	This object is used for flow control of hybrid ports. It is similar to the dot3PauseAdminMode object in dot3PauseTable. It is used to configure pause for fiber media.
INT esmHybridPortCfgInactiveType	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3.1.6	INTEGER	read-only	This object is only applicable to hybrid ports . It indicates the configured inactive media type.
INT esmHybridPortCfgSpeed	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.3.1.1	INTEGER	read-write	The configured port line speed of this ESM port.
INT esmPortAdminStatus	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.7	INTEGER	read-write	The desired state of the interface. The testing(3) state indicates that no operational packets can be passed. When a managed system initializes, all interfaces start with ifAdminStatus in the down(2) state. As a result of either explicit management action or per configuration information retained by the managed system, ifAdminStatus is then changed to either the up(1) or testing(3) states (or remains in the down(2) state).
STR esmPortAlias	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.12	SnmpAdminString	read-write	This object is an 'alias' name for the interface as specified by a network manager, and provides a non-volatile 'handle' for the interface. On the first instantiation of an interface, the value of ifAlias associated with that interface is the zero-length string. As and when a value is written into an instance of ifAlias through a network management set operation, then the agent must retain the supplied value in the ifAlias instance associated with the same interface for as long as that interface remains instantiated, including across all re- initializations/reboots of the network management system, including those which result in a change of the interface's ifIndex value. An example of the value which a network manager might store in this object for a WAN interface is the (Telco's) circuit number/identifier of the interface. Some agents may support write-access only for interfaces having particular values of ifType. An agent which supports write access to this object is required to keep the value in non-volatile storage, but it may limit the length of new values depending on how much storage is already occupied by the current values for other interfaces.
INT esmPortAutoDuplexMode	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.4	INTEGER	read-only	The automatically detected port duplex mode of this ESM port. Note: GigaEthernet supports only Full duplex mode. Default value for 10/100 = Half duplex mode.
INT esmPortAutoSpeed	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.3	INTEGER	read-only	The automatically detected port line speed of this ESM port.
I32 esmPortBcastRateLimit	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.23	Integer32	read-write	The value of the maximum broadcast traffic that can flow through the port. The actual value depends on the port speed if the configured values is greater than the current port speed.
INT esmPortBcastRateLimitEnable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.21	INTEGER	read-write	Enable/disable per port broadcast traffic rate limit. When 'enable' value from esmPortBcastRateLimit object will be applicable to the ingressing broadcast traffic if the speed is greater than the limit else the default limit for the speed will be applied. When it is 'disable' no limit is applied to incoming broadcast traffic which is limited by the port speed.
INT esmPortBcastRateLimitType	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.22	INTEGER	read-write	The unit applicable to the value in esmPortBcastRateLimit object.
INT esmPortCfgAutoNegotiation	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.15	INTEGER	read-write	Allow the user to enable or disable the port auto negotiation.
INT esmPortCfgCrossover	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.16	INTEGER	read-write	Allow the user to configure port crossover. This object is applicable only to copper ports. For fiber ports notapplicable is returned as a status.
INT esmPortCfgDuplexMode	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.6	INTEGER	read-write	The configured port duplex mode of this ESM port. Note: GigaEthernet support only full-duplex.
INT esmPortCfgHybridActiveType	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.18	INTEGER	read-only	This object is only applicable to hybrid ports . It indicates configured active media type.(the operational media type may be different if esmPortCfgHybridMode is configured to be preferredFiber or preferredCopper) For non hybrid ports notapplicable is returned as a status.
INT esmPortCfgHybridMode	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.19	INTEGER	read-write	This object is only applicable to hybrid ports. This allows the user the user to configure the media type with which the port should come up. The user can configure the port to come as copper only or fiber only or either fiber/copper (with preference to one of them).
I32 esmPortCfgMaxFrameSize	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.11	Integer32	read-write	Configure the value of the maximum frame size allow. For 10Mbps the range is upto 1518 bytes. For ports with speed > 10Mbps the value can extend upto 9216 bytes.
INT esmPortCfgPause	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.13	INTEGER	read-write	This object is used to configure the default administrative PAUSE mode for this interface. This object represents the administratively-configured PAUSE mode for this interface. If auto-negotiation is not enabled or is not implemented for the active MAU attached to this interface, the value of this object determines the operational PAUSE mode of the interface whenever it is operating in full-duplex mode. In this case, a set to this object will force the interface into the specified mode. If auto-negotiation is implemented and enabled for the MAU attached to this interface, the PAUSE mode for this interface is determined by auto-negotiation, and the value of this object denotes the mode to which the interface will automatically revert if/when auto-negotiation is later disabled. For more information on what pause values will be autonegotiated based on settings on this object, please refer to the truth table in the users manual. Note that the value of this object is ignored when the interface is not operating in full-duplex mode.
INT esmPortCfgSpeed	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.5	INTEGER	read-write	The configured port line speed of this ESM port.
INT esmPortEEEEnable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.34	INTEGER	read-write	10Gbase-T Energy Efficent Ethernet port parameter.
INT esmPortEPPEnable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.33	INTEGER	read-write	use for port diagnostics
I32 esmPortIF	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.2	Integer32	read-only	The on-board interface number for this Ethernet Port. Port Number has been added to be used by the private Trap.
I32 esmPortIngressRateLimit	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.31	Integer32	read-write	The value of the maximum ingress traffic that can flow through the port. The actual value depends on the port speed if the configured value is greater than the current port speed.
I32 esmPortIngressRateLimitBurst	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.32	Integer32	read-write	The value of ingress traffic burst size in Mbits.
INT esmPortIngressRateLimitEnable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.30	INTEGER	read-write	Enable/disable per port ingress traffic rate limit. When 'enable' value from esmPortIngressRate object will be applicable to the ingressing traffic (BC, MC, UUC) if the speed is greater than the limit else the default limit for the speed will be applied. When it is 'disable' no limit is applied to incoming traffic which is limited by the port speed.
INT esmPortIsFiberChannelCapable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.35	INTEGER	read-write	The port can be configured as Fiber Channel interface (yes) or can not be configured as Fiber Channel interface.
INT esmPortLinkUpDownTrapEnable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.8	INTEGER	read-write	Indicates whether linkUp/linkDown traps should be generated for this interface. By default, this object should have the value enable(1) for interfaces which do not operate on 'top' of any other interface (as defined in the ifStackTable), and disable(2) otherwise.
I32 esmPortMcastRateLimit	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.26	Integer32	read-write	The value of the maximum multicast traffic that can flow through the port. The actual value depends on the port speed if the configured values is greater than the current port speed.
INT esmPortMcastRateLimitEnable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.24	INTEGER	read-write	Enable/disable per port multicast traffic rate limit. When 'enable' value from esmPortMcastRateLimit object will be applicable to the ingressing multicast traffic if the speed is greater than the limit else the default limit for the speed will be applied. When it is 'disable' no limit is applied to incoming multicast traffic which is limited by the port speed.
INT esmPortMcastRateLimitType	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.25	INTEGER	read-write	The unit applicable to the value in esmPortMcastRateLimit object.
INT esmPortOperationalHybridType	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.20	INTEGER	read-only	This object is only applicable to hybrid ports . It indicates the actual media type that has link up and is or will be passing traffic. If link is not present the object will return none(0) value.
I32 esmPortSlot	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.1	Integer32	read-only	The physical Slot number for this Ethernet Port. Slot number has been added to be used by the private Trap.
I32 esmPortUucastRateLimit	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.29	Integer32	read-write	The value of the maximum unknown unicast traffic that can flow through the port. The actual value depends on the port speed if the configured values is greater than the current port speed.
INT esmPortUucastRateLimitEnable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.27	INTEGER	read-write	Enable/disable per port unknown unicast traffic rate limit. When 'enable' value from esmPortUucastRateLimit object will be applicable to the ingressing unknown unicast traffic if the speed is greater than the limit else the default limit for the speed will be applied. When it is 'disable' no limit is applied to incoming unknown unicast traffic which is limited by the port speed.
INT esmPortUucastRateLimitType	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.1.1.28	INTEGER	read-write	The unit applicable to the value in esmPortUucastRate object.
C64 gigaEtherStatsPkts1519to4095Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.16	Counter64	read-only	The total number of packets (including bad packets) received that were between 1519 and 4095 octets in length inclusive (excluding framing bits but including FCS octets). Only for GigaEthernet interfaces
C64 gigaEtherStatsPkts4096to9215Octets	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2.2.1.17	Counter64	read-only	The total number of packets (including bad packets) received that were between 4096 and 9215 octets in length inclusive (excluding framing bits but including FCS octets). Only for GigaEthernet interfaces
physicalPort	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.2
INT portViolationAction	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1.4	INTEGER	read-only	The action determines on violation, what action will taken. Either the port would be shutdown or Admin Down or wait for the timer to expire and the timerAction will determine what needs to be done.
INT portViolationClearPort	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1.7	INTEGER	read-write	When this MIB object is set all violation on the given port will be cleared. The Indices portViolationSource and portViolationReason should be set to 0
portViolationEntry	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1		not-accessible	Port Violation Entry. The entries in this table are indexed by 3 units, 1. ifIndex of the port for which the violation is set 2. source of the violation, the feature or module 3. reason for the violation (sub reason under each source).
portViolationEntryGroup	1.3.6.1.4.1.6486.801.1.2.1.5.1.2.2.12			This table contains the port Violations per port.
NUM portViolationIfIndex	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1.1	InterfaceIndex	not-accessible	The IfIndex of the port that has a violation.
NTF portViolationNotificationTrap	1.3.6.1.4.1.6486.801.1.2.1.5.1.0.8			A Trap will be generated when a port violation is cleared.
INT portViolationReason	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1.3	INTEGER	not-accessible	The Reason for the port violation. This will be application specific. The Reason indicate the violation for the 1st Violation that happened on this port.
portViolations	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5
INT portViolationSource	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1.2	INTEGER	not-accessible	Indicates the source of the port violation. The source is the feature or module that has caused the violation. The list is given below 1. Initiated by Source Learning 2. Initiated by QOS Policy 3. Initiated by Net Sec 4. Initiated by UDLD 5. Initiated by NI supervison (Fabric Stability). When there is no value the value of this will be 0
portViolationTable	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1		not-accessible	This table contains the port Violations per port.
TIK portViolationTimer	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1.5	TimeTicks	read-only	If any timer is associated with the violation This is Zero if no timer is associated.
INT portViolationTimerAction	1.3.6.1.4.1.6486.801.1.2.1.5.1.1.5.1.1.6	INTEGER	read-only	The Timer related action. If set to portDownAfterTimer, no operation will be performed on the port and the port will be shutdown after timer expiry. If set to portUpAfterTimer the port will be shutdown immediately and after the timer expiry the port will brought up..
NTF portViolationTrap	1.3.6.1.4.1.6486.801.1.2.1.5.1.0.7			A Trap will be generated when a port violation occurs. The port violation trap will indicate the source of the violation and the reason for the violation.

RFC description

Alcatel port configuration MIB for Ethernet and Fiber Channel switching modules with interface statistics.

Start monitoring Alcatel-Lucent Enterprise OmniSwitch switches with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ALCATEL-IND1-PORT-MIB