Juniper-IP-MIB

All MIBs › Juniper-IP-MIB

Organization: Juniper Networks, Inc.

Last Updated: 2007-01-17

Category: IP and Core Protocols, Vendor: Juniper

Description: Provides managed objects for IPv4 routing, addressing, and forwarding statistics on Juniper Networks E-series broadband routers.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Juniper-IP-MIB?

Juniper-IP-MIB is a Juniper Networks enterprise MIB that extends standard IP management for Juniper E-series broadband edge routers, covering IPv4 routing, addressing, and forwarding behavior. It exposes configuration-oriented data such as router identifiers, source-routing policy, VPN identifiers, and BGP confederation/community formatting, alongside summary counters for interface state. It supports monitoring of hardware and software health indirectly through interface-level status, most notably the juniIpIfSummary counters that report how many IP interfaces are administratively and operationally up versus down, which is a direct signal of link or software-driven interface failures. It builds on and complements the standard IETF IP-MIB and IP-FORWARD-MIB, adding Juniper-specific routing and VPN attributes not covered by those base standards. It is deployed on carrier and enterprise edge routers where operators need Juniper-specific IP-layer visibility beyond generic SNMP IP MIBs. Engineers can download the Juniper-IP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Juniper-IP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Juniper Networks E-series broadband routers

Monitoring Examples

An operator would poll juniIpIfSummaryTotalIntfUp and juniIpIfSummaryTotalIntfDown alongside juniIpIfSummaryTotalIntfProtDown to detect a spike in interfaces that are administratively up but protocol-down, indicating a routing or negotiation failure. Checking juniIpRouterId confirms the router's configured identity for troubleshooting BGP or OSPF adjacency issues, while juniIpVpnIdOui and juniIpVpnIdIndex would be read to verify VPN identifier configuration on a per-customer basis. The juniIpObjects and juniIpInterface subtrees provide the structural grouping an NMS would walk to correlate these values with specific interfaces.

What Can Be Monitored

total IP interfaces configured
interfaces administratively up/down
interfaces protocol up/down
router ID
source routing admin status
VPN identifier configuration

Imported Objects

From IF-MIB

InterfaceIndex
InterfaceIndexOrZero
ifIndex	OBJECT-TYPE

From IP-FORWARD-MIB

ipCidrRouteEntry	OBJECT-TYPE
ipCidrRouteNumber	OBJECT-TYPE

From Juniper-MIBs

juniMibs

MODULE-IDENTITY

From Juniper-TC

JuniEnable
JuniIpAddrLessIf
JuniNextIfIndex

From SNMPv2-CONF

MODULE-COMPLIANCE
NOTIFICATION-GROUP
OBJECT-GROUP

From SNMPv2-SMI

Counter64
Gauge32
Integer32
IpAddress
MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

RowStatus
TruthValue

How to Use in IPNetwork Monitor

Example using juniIpIfStatsInPackets OID:

Select a Juniper Networks E-series broadband router (IPv4 routing/addressing) as the target host to create a monitor — the SNMP service should be up and running on it. Click New Monitor, then check SNMP Custom on the Favorites tab, click Next, and confirm the host. On the next page, click Select... to open the built-in SNMP MIB Browser and type juniIpIfStatsInPackets into the Find box to locate it in the OID tree, selecting the specific row/instance you want to monitor since this is a table column, then select it and click OK. The number of packets received on this interface. On the monitor's Main parameters page you can set the target's SNMP port (default 161), credentials, polling interval, and other settings — see the SNMP Monitor help for details. On the State conditions and Alerting tabs, configure when the monitor should change state and trigger an alert; since this is a Counter64-type OID, Value bounds is the most useful condition here — trigger an alert if the counter increases sharply between polls relative to its normal baseline, since an unexpected spike often reflects a real change in traffic or activity. Click Finish to create the monitor; you can adjust any parameter later.

OIDs

OID symbolic	OID numeric	Type	Access	Description
juniIpMIB	1.3.6.1.4.1.4874.2.2.12			The IP Protocol MIB for the Juniper Networks enterprise.
juniIpObjects	1.3.6.1.4.1.4874.2.2.12.1
juniIpInterface	1.3.6.1.4.1.4874.2.2.12.1.1
JUN juniIpNextIfIndex	1.3.6.1.4.1.4874.2.2.12.1.1.1	JuniNextIfIndex	read-only	Coordinate ifIndex value allocation for entries in juniIpIfTable. A GET of this object returns the next available ifIndex value to be used to create an entry in the associated interface table; or zero, if no valid ifIndex value is available. This object also returns a value of zero when it is the lexicographic successor of a varbind presented in an SNMP GETNEXT or GETBULK request, for which circumstance it is assumed that ifIndex allocation is unintended. Successive GETs will typically return different values, thus avoiding collisions among cooperating management clients seeking to create table entries simultaneously.
juniIpIfTable	1.3.6.1.4.1.4874.2.2.12.1.1.2		not-accessible	This table contains entries for IP interfaces present in the system.
juniIpIfEntry	1.3.6.1.4.1.4874.2.2.12.1.1.2.1		not-accessible	Each entry describes the characteristics of an IP interface. Creating/deleting entries in this table causes corresponding entries for be created/deleted in ifTable/ifXTable/juniIfTable.
NUM juniIpIfIndex	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.1	InterfaceIndex	not-accessible	The ifIndex of the IP interface. When creating entries in this table, suitable values for this object are determined by reading juniIpNextIfIndex.
ROW juniIpIfRowStatus	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.2	RowStatus	read-create	Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this table, the following entry objects MUST be explicitly configured: juniIpIfRowStatus juniIpIfLowerIfIndex In addition, when creating an entry the following conditions must hold: A value for juniIpIfIndex must have been determined previously, typically by reading juniIpNextIfIndex. The interface identified by a nonzero juniIpIfLowerIfIndex must exist. If juniIpIfType is configured to be 'loopback' or 'null', juniIpIfLowerIfIndex must be set to zero. The selected value of juniIpIfType must be compatible with the underlying media interface identified by juniIpIfLowerIfIndex. Once created, the following objects may not be modified: juniIpIfLowerIfIndex juniIpIfType juniIpIfTypeId A corresponding entry in ifTable/ifXTable/juniIfTable is created/ destroyed as a result of creating/destroying an entry in this table.
NUM juniIpIfLowerIfIndex	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.3	InterfaceIndexOrZero	read-create	The ifIndex of a media interface over which this IP interface is to be layered. A value of zero is used when juniIpIfType is specified to be loopback(4) or null(5).
INT juniIpIfType	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.4	INTEGER	read-create	The type of network interface.
U32 juniIpIfTypeId	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.5	Unsigned32	read-create	A numerical distinguisher relevant for the loopback and null IP interface types. loopback Must be unique for all IP interfaces of this type. null Must be unique for all IP interfaces of this type. (FOR IMPLEMENTATIONS THAT SUPPORT ONE AND ONLY ONE NULL INTERFACE, THE VALUE ZERO MUST BE USED.) For all other IP interface types, this object is not relevant, reports a value of zero when read, and must be given a value of zero if explicitly configured during creation.
JUN juniIpIfSAValidationEnable	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.6	JuniEnable	read-create	Enable/disable source address validation on this IP network interface.
INT juniIpIfCreationType	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.7	INTEGER	read-only	Specify if the interface was created due to static configuration or due to some dynamic event. Dynamic interfaces are not stored in NVS.
U32 juniIpIfProfileId	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.8	Unsigned32	read-only	Identified the profile used when creating a dynamic interface.
JUN juniIpIfAlwaysUp	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.9	JuniEnable	read-create	When enabled, the interface is determined to be up regardless of the state of any lower layer interfaces.
JUN juniIpIfLoopback	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.10	JuniEnable	read-create	Indicates whether the interface is a loopback type interface. This object has been replaced by juniIpIfInheritNum.
NUM juniIpIfLoopbackUid	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.11	InterfaceIndexOrZero	read-create	Specify the interface index of a loopback interface whose IP address should be used when sourcing traffic on this interface. Useful for unnumbered interfaces. This object has been replaced by juniIpIfInheritNumUid.
I32 juniIpIfDebounceTime	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.12	Integer32	read-create	Specifies the time in milliseconds that a layer 2 interface must remain in a state before it is conveyed to the IP layer. Useful for interfaces that experience brief outages that should not constitute a route flap. A value of 0 indicates that the feature is disabled.
JUN juniIpIfForwarding	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.13	JuniEnable	read-create	Enable/disable the forwarding of IP traffic to/from this interface. This is currently only applicable to the out-of-band management port.
JUN juniIpIfForceFragmentation	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.14	JuniEnable	read-create	Force the fragmentation of all IP packets greater than the interface MTU even if the DF bit is set.
JUN juniIpIfSharesLowerUid	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.15	JuniEnable	read-only	Identifies the interface as sharing a lower interface with another interface vs owning it outright.
U32 juniIpIfFilterOptions	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.16	Unsigned32	read-create	Bit mask to configure the interface to filter packets with IP header options. Currently, either no bits or all bits may be set.
OCT juniIpIfName	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.17	OCTET STRING	read-create	Specify the IP interface discriminator for an IP interface not attached to a layer 2 interface with a specific location.
U32 juniIpIfArpTimeout	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.18	Unsigned32	read-create	Specify the ARP timeout for this interface in seconds.
U32 juniIpIfAdminSpeed	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.19	Unsigned32	read-create	Set an administrative speed for the interface that overrides the speed learned from the lower layer. A value of 0 indicates no speed is specified.
INT juniIpIfMultipathMode	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.20	INTEGER	read-create	Configure the mode this interface should use when forwarding equal-cost multipath traffic.
IP juniIpIfSharedNhAddr	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.21	IpAddress	read-create	The IP address of either a direct or indirect next-hop toward which this shared interface should point.
U32 juniIpIfSharedNhRouterId	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.22	Unsigned32	read-create	The identifier for the domain of a virtual router in which the juniIpIfSharedNhAddr should be resolved.
IP juniIpIfPrimaryIpAddress	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.23	IpAddress	read-only	The IP address of the primary IP network on an interface.
IP juniIpIfPrimaryIpMask	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.24	IpAddress	read-only	The IP address mask of the primary IP network on an interface.
I32 juniIpIfOperDebounceTime	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.25	Integer32	read-only	Indicates the operational time in milliseconds that a layer2 interface must remain in a state before it is conveyed to the IP layer. Useful for interfaces that experience brief outages that should not constitute a route flap. A value of 0 indicates that the feature is disabled.
U32 juniIpIfRouterIndex	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.26	Unsigned32	read-only	The index or ID of the router.
JUN juniIpIfInheritNum	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.27	JuniEnable	read-only	Indicates whether this numbered interface is referenced by unnumbered interfaces.
NUM juniIpIfInheritNumUid	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.28	InterfaceIndexOrZero	read-create	Specify the interface index of a numbered interface whose IP address should be used when sourcing traffic on this interface. Useful for unnumbered interfaces.
INT juniIpIfAnalyzerMode	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.29	INTEGER	read-create	Used to set the interface to analyzer mode. When enabled(1), all IP packets entering this interface and all non-mirror IP packets leaving this interface will be dropped. The value default(2) specifies that this interface will be the default analyzer port for the virtual-router where the interface resides.
JUN juniIpIfAutoConfigure	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.30	JuniEnable	read-create	When enabled, IP subscriber interfaces are created dynamically based on any attributes defined in the service-profile and the rules associated with the DCM profile selected for this subscriber.
I32 juniIpIfTcpMss	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.31	Integer32	read-create	Configures TCP MSS value for an IP interface. When configured, MSS value of TCP SYN packets received or transmitted on the interface will be compared with the configured value and lowest of the two will replace the value in the packet.
U32 juniIpIfInitSeqPrefOper	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.32	Unsigned32	read-only	Indicates the operational warm-restart replay initial sequence preference value for an IP interface. Following an HA SRP switchover, high-preference (value 1) IP interfaces are replayed first, followed by static routes, and then low-preference (value 0) IP interfaces. This allows static routes that are dependent on high-preference interfaces to be resolved and routing protocols to exchange information with peers over high-preference interfaces before low-preference interfaces are replayed. An IP interface is designated as high-preference either (1) implicitly by configuring an IGP or PIM protocol on that interface, or (2) explicitly by juniIpIfInitSeqPrefAdmin (or CLI) configuration.
U32 juniIpIfInitSeqPrefAdmin	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.33	Unsigned32	read-create	Configures the warm-restart replay initial sequence preference value for an IP interface. See the juniIpIfInitSeqPrefOper description for more information.
JUN juniIpIfArpSpoofCheck	1.3.6.1.4.1.4874.2.2.12.1.1.2.1.34	JuniEnable	read-create	When enabled, IP ARP spoof checking is performed on ARP packets received on the IP interface.
juniIpIfStatsTable	1.3.6.1.4.1.4874.2.2.12.1.1.3		not-accessible	This table contains entries for IP interfaces present in the system.
juniIpIfStatsEntry	1.3.6.1.4.1.4874.2.2.12.1.1.3.1		not-accessible	Each entry contains statistics for an IP interface.
NUM juniIpIfStatsIndex	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.1	InterfaceIndex	not-accessible	The ifIndex of the IP interface.
C64 juniIpIfStatsInPacketsEx	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.2	Counter64	read-only	The number of packets received on this interface.
C64 juniIpIfStatsInOctets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.3	Counter64	read-only	The number of octets received on this interface.
C64 juniIpIfStatsInPoliciedPackets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.4	Counter64	read-only	The number of packets dropped due to rate limiters attached to this interface.
C64 juniIpIfStatsInPoliciedOctets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.5	Counter64	read-only	The number of octets dropped due to rate limiters attached to this interface.
C64 juniIpIfStatsInErrorPackets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.6	Counter64	read-only	The number of packets received with errors on this interface.
C64 juniIpIfStatsInSpoofedPackets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.7	Counter64	read-only	The number of packets received on this interface with destination unknown.
C64 juniIpIfStatsInForwardedPackets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.8	Counter64	read-only	The number of packets received on this interface that were forwarded by any interface in the system.
C64 juniIpIfStatsInForwardedOctets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.9	Counter64	read-only	The number of octets received on this interface that were forwarded by any interface in the system.
C64 juniIpIfStatsOutForwardedPackets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.10	Counter64	read-only	The number of packets forwarded by this interface.
C64 juniIpIfStatsOutForwardedOctets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.11	Counter64	read-only	The number of octets forwarded by this interface.
C64 juniIpIfStatsOutSchedDropPackets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.12	Counter64	read-only	The number of packets dropped at this interface due to output queue congestion.
C64 juniIpIfStatsOutSchedDropOctets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.13	Counter64	read-only	The number of octets dropped at this interface due to output queue congestion.
C64 juniIpIfStatsOutRequestedPackets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.14	Counter64	read-only	The number of packets requested for transmission at this interface.
C64 juniIpIfStatsOutRequestedOctets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.15	Counter64	read-only	The number of octets requested for transmission at this interface.
C64 juniIpIfStatsOutPoliciedPackets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.16	Counter64	read-only	The number of packets dropped due to rate limiters attached to this interface.
C64 juniIpIfStatsOutPoliciedOctets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.17	Counter64	read-only	The number of octets dropped due to rate limiters attached to this interface.
C64 juniIpIfStatsGreenOutSchedDropPackets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.18	Counter64	read-only	The number of packets dropped at this interface due to output queue congestion in the green output queue. The green output queue has lowest drop probability.
C64 juniIpIfStatsYellowOutSchedDropPackets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.19	Counter64	read-only	The number of packets dropped at this interface due to output queue congestion in the yellow output queue. The yellow output queue has medium level drop probability.
C64 juniIpIfStatsRedOutSchedDropPackets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.20	Counter64	read-only	The number of packets dropped at this interface due to output queue congestion in the red output queue. The red output queue has highest level drop probability.
C64 juniIpIfStatsGreenOutSchedDropOctets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.21	Counter64	read-only	The number of octets dropped at this interface due to output queue congestion in the green output queue. The green output queue has the lowest drop probability.
C64 juniIpIfStatsYellowOutSchedDropOctets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.22	Counter64	read-only	The number of octets dropped at this interface due to output queue congestion in the yellow output queue. The yellow output queue has the medium drop probability.
C64 juniIpIfStatsRedOutSchedDropOctets	1.3.6.1.4.1.4874.2.2.12.1.1.3.1.23	Counter64	read-only	The number of octets dropped at this interface due to output queue congestion in the red output queue. The red output queue has the highest drop probability.
juniIpIfAssocTable	1.3.6.1.4.1.4874.2.2.12.1.1.4		not-accessible	This table contains entries of interfaces present in the system.
juniIpIfAssocEntry	1.3.6.1.4.1.4874.2.2.12.1.1.4.1		not-accessible	Each entry in this table returns the ifIndex of the IP interface associated with the lower layer ifIndex supplied as the index to this table. The purpose of this table is to translate L2 interfaces to corresponding L3 interfaces for billing applications. Since interesting billing related statistics are kept at L3, it is often useful to know the L2-L3 relationship. Note that this table is not confined to L2-L3 relationships. Any interface sublayer can be used to access this table to determine the relationship with the L3 interface.
NUM juniIpIfAssocLowerIfIndex	1.3.6.1.4.1.4874.2.2.12.1.1.4.1.1	InterfaceIndex	not-accessible	The ifIndex of the lower layer interface.
NUM juniIpIfAssocIpIfIndex	1.3.6.1.4.1.4874.2.2.12.1.1.4.1.2	InterfaceIndexOrZero	read-only	The ifIndex of the IP interface associated with the lower layer juniIpIfAssocLowerIfIndex. In cases where there is not a 1 to 1 relationship between lower layer and higher layer IP interface, a zero value juniIpIfAssocIpIfIndex is returned; this includes the case where an IP interface has not yet been configued at the top of the interface column. An example usage of this table: Assume a user needs to know the ifIndex relationship for all interfaces with the L3 IP interface. Then starting at the bottom of the stack below, the ATM and AAL5's ifIndex would be used to access the table. The agent will return 0 for each of these cases because multiple customer's traffic is demultiplexed at these levels. IP_1 PPP IP_2 ATM1483_1 ATM1483_2 \ / AAL5 ATM If the ATM1483_1 ifIndex is used to access this table, then the value of juniIpIfAssocLowerIfIndex will be set to the ifIndex of IP_1. Similarily, if the ATM1483_2 ifIndex is used to access this table, the juniIpifAssocLowerIfIndex will set to the ifIndex of IP_2.
juniIpAddress	1.3.6.1.4.1.4874.2.2.12.1.2
juniIpAddrGlobals	1.3.6.1.4.1.4874.2.2.12.1.2.1
I32 juniIpArpTimeout	1.3.6.1.4.1.4874.2.2.12.1.2.1.1	Integer32	read-write	Timeout, in seconds, for ARP requests issued by this entity.
juniIpAddrTable	1.3.6.1.4.1.4874.2.2.12.1.2.2		not-accessible	IP addressing information for this entity's IP network interfaces. Representation of both numbered and unnumbered IP interfaces is supported.
juniIpAddrEntry	1.3.6.1.4.1.4874.2.2.12.1.2.2.1		not-accessible	IP addressing information for one of this entity's IP network interfaces. This interface could be either numbered or unnumbered. The following objects correspond to (read-only) counterparts in the IP-MIB ipAddrTable: juniIpAdEntAddr juniIpAdEntIfIndex juniIpAdEntNetMask juniIpAdEntBcastAddr juniIpAdEntReasmMaxSize
JUN juniIpAdEntAddr	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.1	JuniIpAddrLessIf	not-accessible	The IP address for a numbered IP network interface, if this object's value has the form 'a.b.c.d', where 'a' is nonzero; or, the ifIndex (interpreting the low 24 bits of this value as an integer) of an unnumbered ('address-less') IP interface, if this object's value has the form '0.b.c.d'.
NUM juniIpAdEntIfIndex	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.2	InterfaceIndex	read-create	The ifIndex of the network interface to which this entry's IP addressing mode pertains.
IP juniIpAdEntNetMask	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.3	IpAddress	read-create	The IP subnet mask associated with the IP address of this entry. The network and host bit fields of the mask are filled with 1's and 0's, respectively. If this entry represents an unnumbered IP interface, this object should have a value of all ones.
I32 juniIpAdEntBcastAddr	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.4	Integer32	read-only	The value of the least-significant bit in the IP broadcast address used for sending datagrams on the IP network interface associated with this entry. For example, when the Internet standard all-ones broadcast address is used, the value will be 1. This value applies to both the subnet and network broadcasts addresses used by the entity on this interface.
I32 juniIpAdEntReasmMaxSize	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.5	Integer32	read-only	The size of the largest IP datagram which this entity can re-assemble from incoming IP fragmented datagrams received on this interface.
ROW juniIpAdEntRowStatus	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.6	RowStatus	read-create	Controls the creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create entries for both numbered and unnumbered IP interfaces, the following entry objects MUST be explicitly configured: juniIpAdEntRowStatus juniIpAdEntIfIndex To create an entry for a numbered IP interface, the following conditions must also hold: To create an entry for an unnumbered IP interface, the following conditions must also hold: juniIpAdEntUnnumInheritNumIfIndex must be configured with a nonzero ifIndex value of an IP numbered interface.
JUN juniIpAdEntAdminStatus	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.7	JuniEnable	read-create	Enable/disable operation of IP on this IP network interface.
JUN juniIpAdEntArpRspEnable	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.8	JuniEnable	read-create	Enable/disable ARP response on this IP network interface.
JUN juniIpAdEntProxyArpRspEnable	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.9	JuniEnable	read-create	Enable/disable proxy ARP response on this IP network interface.
JUN juniIpAdEntIgmpEnable	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.10	JuniEnable	read-create	Enable/disable IGMP operation on this IP network interface.
JUN juniIpAdEntDirectedBcastEnable	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.11	JuniEnable	read-create	Enable/disable forwarding of directed broadcasts on this IP network interface.
JUN juniIpAdEntIcmpRedirectEnable	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.12	JuniEnable	read-create	Enable/disable transmission of ICMP Redirect messages on this IP network interface.
JUN juniIpAdEntIcmpMaskReplyEnable	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.13	JuniEnable	read-create	Enable/disable transmission of ICMP Mask Reply messages on this IP network interface.
JUN juniIpAdEntIcmpUnreachEnable	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.14	JuniEnable	read-create	Enable/disable transmission of ICMP Unreachable messages on this IP network interface.
I32 juniIpAdEntMtu	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.15	Integer32	read-create	The configured MTU size for this IP network interface. If set to zero, the default MTU size, as determined by the underlying network media, is used.
NUM juniIpAdEntUnnumLoopbackIfIndex	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.16	InterfaceIndexOrZero	read-create	For unnumbered interfaces, the ifIndex of the IP loopback interface whose IP address is used as the source IP address for IP packets transmitted on the unnumbered network. For numbered interfaces, this object has a value of zero. This object has been replaced by juniIpAdEntUnnumInheritNumIfIndex.
JUN juniIpAdEntIrdpEnable	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.17	JuniEnable	read-create	Controls whether ICMP Router Discovery Protocol operation is permitted to be sent on this network.
JUN juniIpAdEntAccessRouteEnable	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.18	JuniEnable	read-create	If enabled, then establishment/loss of a point-to-point network connection causes a host route for the remote host to be created/deleted automatically.
IP juniIpAdEntAccessRouteHost	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.19	IpAddress	read-only	If an access route has been established, the IP address of the remote host is reported by this object; otherwise, this object contains the value 0.0.0.0.
JUN juniIpAdEntIsSecondary	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.20	JuniEnable	read-create	If enabled, then the IP address corresponding to this entry is a secondary address. If disabled, then the IP address corresponding to this entry is te primary address.
NUM juniIpAdEntUnnumInheritNumIfIndex	1.3.6.1.4.1.4874.2.2.12.1.2.2.1.21	InterfaceIndexOrZero	read-create	For unnumbered interfaces, the ifIndex of the IP numbered interface whose IP address is used as the source IP address for IP packets transmitted on the unnumbered network. For numbered interfaces, this object has a value of zero.
juniIpRoute	1.3.6.1.4.1.4874.2.2.12.1.3
juniIpRouteGlobals	1.3.6.1.4.1.4874.2.2.12.1.3.1
I32 juniIpRouteLimit	1.3.6.1.4.1.4874.2.2.12.1.3.1.1	Integer32	read-write	Maximum number of IP routes maintained by this entity. Setting a value lower than the current number of routes prevents additional routes from being learned or configured, but does not cause existing excess routes to be deleted to enforce the new limit.
U32 juniIpRouteTableLimit	1.3.6.1.4.1.4874.2.2.12.1.3.1.2	Unsigned32	read-write	The VRF Route Table Maximum Number of Routes Limit.
U32 juniIpRouteTableWarnPercent	1.3.6.1.4.1.4874.2.2.12.1.3.1.3	Unsigned32	read-write	The VRF Route Table Percentage of the Route Limit at which to issue a warning. The percentage is only valid when juniIpRouteTableWarnOnly is false. It must be set to 0 if juniIpRouteTableWarnOnly is true.
T/F juniIpRouteTableWarnOnly	1.3.6.1.4.1.4874.2.2.12.1.3.1.4	TruthValue	read-write	The VRF Route Table Maximum Number of Routes Warning flag. Do not actually limit the number of routes in the table
U32 juniIpRouteTableWarnThreshold	1.3.6.1.4.1.4874.2.2.12.1.3.1.5	Unsigned32	read-only	The computed number of route to issue a warning. If juniIpRouteTableWarnOnly is true this value will be juniIpRouteTableLimit and if juniIpRouteTableWarnOnly is false it will be juniIpRouteTableLimit * juniIpRouteTableWarnPercentage
juniIpRouteStaticTable	1.3.6.1.4.1.4874.2.2.12.1.3.2		not-accessible	Table of static routes configured on this entity. The object definitions and indexing for this table are chosen to closely align with the IP-FORWARD-MIB's ipCidrRouteTable. This table serves three purposes: 1. Provide the means for configuring static routes. 2. Provide an efficient view of static routes (otherwise they must be observed by traversing the entire routing table). 3. Provide view of static routes configured on network interfaces that are currently inactive. (In this implementation, static routes configured on inactive interfaces are not visible in the routing table.)
juniIpRouteStaticEntry	1.3.6.1.4.1.4874.2.2.12.1.3.2.1		not-accessible	A static route.
IP juniIpRouteStaticDest	1.3.6.1.4.1.4874.2.2.12.1.3.2.1.1	IpAddress	read-only	The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the juniIpRouteStaticMask object is not equal to x.
IP juniIpRouteStaticMask	1.3.6.1.4.1.4874.2.2.12.1.3.2.1.2	IpAddress	read-only	Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the juniIpRouteStaticDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the juniIpRouteStaticMask by reference to the IP Address Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the juniIpRouteStaticDest object is not equal to juniIpRouteStaticDest.
I32 juniIpRouteStaticPref	1.3.6.1.4.1.4874.2.2.12.1.3.2.1.3	Integer32	read-only	The preference of this static route. Higher values correspond to higher preference. A static route with preference of zero will never be installed as an active route.
JUN juniIpRouteStaticNextHop	1.3.6.1.4.1.4874.2.2.12.1.3.2.1.4	JuniIpAddrLessIf	read-only	The address of the next hop toward the destination.
ROW juniIpRouteStaticRowStatus	1.3.6.1.4.1.4874.2.2.12.1.3.2.1.5	RowStatus	read-create	The row status variable, used according to row installation and removal conventions.
I32 juniIpRouteStaticIfIndex	1.3.6.1.4.1.4874.2.2.12.1.3.2.1.6	Integer32	read-create	The ifIndex value which identifies the local interface through which the next hop of this route should be reached. A value of zero means the router should automatically determine the interface through which the specified next-hop address is reached. An implementation may disallow non-zero values from being configured.
INT juniIpRouteStaticStatus	1.3.6.1.4.1.4874.2.2.12.1.3.2.1.7	INTEGER	read-only	The operational status of this static route. active(0) indicates this route is currently being used to reach the specified destination. inactive(1) indicates this route is considered valid, but currently is superseded by another routing table entry for the destination, having a higher preference value. incomplete(2) indicates this route entry contains information that is incomplete, or is inconsistent with other system configuration (for example, the interface specified in juniIpRouteStaticIfIndex does not exist).
I32 juniIpRouteStaticNextHopAS	1.3.6.1.4.1.4874.2.2.12.1.3.2.1.8	Integer32	read-create	The Autonomous System Number of the Next Hop. The semantics of this object are determined by the routing-protocol specified in the route's ipCidrRouteProto value. When this object is unknown or not relevant its value should be set to zero.
I32 juniIpRouteStaticMetric	1.3.6.1.4.1.4874.2.2.12.1.3.2.1.9	Integer32	read-create	The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipCidrRouteProto value. If this metric is not used, its value should be set to -1.
U32 juniIpRouteStaticTag	1.3.6.1.4.1.4874.2.2.12.1.3.2.1.10	Unsigned32	read-create	A tag value for this static route.
juniIpCidrRouteTable	1.3.6.1.4.1.4874.2.2.12.1.3.3		not-accessible	Table of routes active on this entity. This table is an augmentation of the IP-FORWARD-MIB's ipCidrRouteTable.
juniIpCidrRouteEntry	1.3.6.1.4.1.4874.2.2.12.1.3.3.1		not-accessible	Additional attributes of an active route.
I32 juniIpCidrRoutePref	1.3.6.1.4.1.4874.2.2.12.1.3.3.1.1	Integer32	read-only	The preference of this route. Higher values correspond to higher preference.
IP juniIpCidrRouteArea	1.3.6.1.4.1.4874.2.2.12.1.3.3.1.2	IpAddress	read-only	The Area to which this route pertains. A value of 0.0.0.0 indicates no area is identified.
U32 juniIpCidrRouteTag	1.3.6.1.4.1.4874.2.2.12.1.3.3.1.3	Unsigned32	read-only	A tag value for this route.
juniIpRouteStaticBFDTable	1.3.6.1.4.1.4874.2.2.12.1.3.4		not-accessible	The Juniper IP interface table describes the BFD-specific characteristics of interfaces.
juniIpRouteStaticBFDEntry	1.3.6.1.4.1.4874.2.2.12.1.3.4.1		not-accessible	The Juniper IP interface table describes the BFD-specific characteristics of one interface.
T/F juniIpRouteStaticBfdEnable	1.3.6.1.4.1.4874.2.2.12.1.3.4.1.1	TruthValue	read-create	This variable indicates whether BFD session on the interface is active or not
I32 juniIpRouteStaticBfdMinRxInterval	1.3.6.1.4.1.4874.2.2.12.1.3.4.1.2	Integer32	read-create	This variable specifies upper-limit on rate local-system requires remote-system to transmit bfd control-packets [milliseconds]
I32 juniIpRouteStaticBfdMinTxInterval	1.3.6.1.4.1.4874.2.2.12.1.3.4.1.3	Integer32	read-create	This variable specifies lower-limit on rate local-system requires remote-system to transmit bfd control-packets [milliseconds]
I32 juniIpRouteStaticBfdMultiplier	1.3.6.1.4.1.4874.2.2.12.1.3.4.1.4	Integer32	read-create	This variable specifies detection-multiplier
juniIpGlobals	1.3.6.1.4.1.4874.2.2.12.1.4
I32 juniIpDebounceTime	1.3.6.1.4.1.4874.2.2.12.1.4.1	Integer32	read-write	The time in milliseconds that an event has to be in the same state before being reported.
IP juniIpRouterId	1.3.6.1.4.1.4874.2.2.12.1.4.2	IpAddress	read-write	The router-id that this IP router will use to identify itself.
JUN juniIpSourceRoutingAdminStatus	1.3.6.1.4.1.4874.2.2.12.1.4.3	JuniEnable	read-write	The administrative setting for source routing.
I32 juniIpVpnIdOui	1.3.6.1.4.1.4874.2.2.12.1.4.4	Integer32	read-write	The OUI portion of the VPN identifier. This object must be set coincident with the index portion of the VpnId (juniIpVpnIdIndex), otherwise the set will fail.
IP juniIpVpnIdIndex	1.3.6.1.4.1.4874.2.2.12.1.4.5	IpAddress	read-write	The index portion of the VPN identifier. This object must be set coincident with the OUI portion of the VpnId (juniIpVpnOui), otherwise the set will fail.
T/F juniIpBgpCommunityNewFormat	1.3.6.1.4.1.4874.2.2.12.1.4.6	TruthValue	read-write	The BGP community format to be used. Set to true to use the community number, as number format.
T/F juniIpBgpAsConfedSetNewFormat	1.3.6.1.4.1.4874.2.2.12.1.4.7	TruthValue	read-write	The BGP as confederation set format to be used. Set to true to display the confederation set as a comma separated list, enclosed in squared braces.
juniIpIfSummary	1.3.6.1.4.1.4874.2.2.12.1.5
G32 juniIpIfSummaryTotalIntf	1.3.6.1.4.1.4874.2.2.12.1.5.1	Gauge32	read-only	The total number of IP interfaces.
G32 juniIpIfSummaryTotalIntfUp	1.3.6.1.4.1.4874.2.2.12.1.5.2	Gauge32	read-only	The total number of IP interfaces in operational state UP.
G32 juniIpIfSummaryTotalIntfDown	1.3.6.1.4.1.4874.2.2.12.1.5.3	Gauge32	read-only	The total number of IP interfaces in operational state DOWN.
G32 juniIpIfSummaryTotalIntfProtUp	1.3.6.1.4.1.4874.2.2.12.1.5.4	Gauge32	read-only	The total number of IP interfaces in protocol state UP.
G32 juniIpIfSummaryTotalIntfProtDown	1.3.6.1.4.1.4874.2.2.12.1.5.5	Gauge32	read-only	The total number of IP interfaces in protocol state DOWN.
G32 juniIpIfSummaryTotalIntfProtNotPresent	1.3.6.1.4.1.4874.2.2.12.1.5.6	Gauge32	read-only	The total number of IP interfaces in protocol state NOT PRESENT.
juniIpRouteSummary	1.3.6.1.4.1.4874.2.2.12.1.6
juniIpRouteUnicastSummary	1.3.6.1.4.1.4874.2.2.12.1.6.1
G32 juniIpRouteSummaryUnicastTotalRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.1.1	Gauge32	read-only	The total number of Unicast IP routes.
G32 juniIpRouteSummaryUnicastTotalBytes	1.3.6.1.4.1.4874.2.2.12.1.6.1.2	Gauge32	read-only	Total number of bytes in unicast route entries.
G32 juniIpRouteSummaryUnicastIsisRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.1.3	Gauge32	read-only	The total number of Unicast IP ISIS routes.
G32 juniIpRouteSummaryUnicastIsisLevel1Routes	1.3.6.1.4.1.4874.2.2.12.1.6.1.4	Gauge32	read-only	The total number of Unicast IP Level 1 ISIS routes.
G32 juniIpRouteSummaryUnicastIsisLevel2Routes	1.3.6.1.4.1.4874.2.2.12.1.6.1.5	Gauge32	read-only	The total number of Unicast IP Level 2 ISIS routes.
G32 juniIpRouteSummaryUnicastRipRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.1.6	Gauge32	read-only	The total number of Unicast IP RIP routes.
G32 juniIpRouteSummaryUnicastStaticRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.1.7	Gauge32	read-only	The total number of Unicast IP Static routes.
G32 juniIpRouteSummaryUnicastConnectedRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.1.8	Gauge32	read-only	The total number of Unicast IP Connected routes.
G32 juniIpRouteSummaryUnicastBgpRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.1.9	Gauge32	read-only	The total number of Unicast IP BGP routes.
G32 juniIpRouteSummaryUnicastOspfRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.1.10	Gauge32	read-only	The total number of Unicast IP OSPF routes.
G32 juniIpRouteSummaryUnicastIntraAreaOspfRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.1.11	Gauge32	read-only	The total number of Unicast IP Intra Area OSPF routes.
G32 juniIpRouteSummaryUnicastInterAreaOspfRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.1.12	Gauge32	read-only	The total number of Unicast IP Inter Area OSPF routes.
G32 juniIpRouteSummaryUnicastExternalOspfRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.1.13	Gauge32	read-only	The total number of Unicast IP External OSPF routes.
G32 juniIpRouteSummaryUnicastOtherInternalRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.1.14	Gauge32	read-only	The total number of Unicast IP Other Internal routes.
G32 juniIpRouteSummaryUnicastAccessRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.1.15	Gauge32	read-only	The total number of Unicast IP Access routes.
G32 juniIpRouteSummaryUnicastIntCreatedAccessHostRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.1.16	Gauge32	read-only	The total number of Unicast IP Internally Created Access Host routes.
G32 juniIpRouteSummaryUnicastIntDialoutRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.1.17	Gauge32	read-only	The total number of Unicast IP Internally Created Dialout routes.
G32 juniIpRouteSummaryUnicastRouteMemoryActive	1.3.6.1.4.1.4874.2.2.12.1.6.1.18	Gauge32	read-only	Unicast IP Route Memory Storage.
IP juniIpRouteSummaryUnicastLastRouteAddedOrDeletedIP	1.3.6.1.4.1.4874.2.2.12.1.6.1.19	IpAddress	read-only	IP address for last Unicast route added or deleted.
IP juniIpRouteSummaryUnicastLastRouteAddedOrDeletedMask	1.3.6.1.4.1.4874.2.2.12.1.6.1.20	IpAddress	read-only	Subnet mask for last Unicast route added or deleted.
INT juniIpRouteSummaryUnicastLastRouteAddedOrDeletedClient	1.3.6.1.4.1.4874.2.2.12.1.6.1.21	INTEGER	read-only	Client for last Unicast route added or deleted.
OCT juniIpRouteSummaryUnicastLastRouteAddedOrDeletedDate	1.3.6.1.4.1.4874.2.2.12.1.6.1.22	OCTET STRING	read-only	Date for last Unicast route added or deleted.
juniIpRouteMulticastSummary	1.3.6.1.4.1.4874.2.2.12.1.6.2
G32 juniIpRouteSummaryMulticastTotalRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.1	Gauge32	read-only	The total number of Multicast IP routes.
G32 juniIpRouteSummaryMulticastTotalBytes	1.3.6.1.4.1.4874.2.2.12.1.6.2.2	Gauge32	read-only	Total number of bytes in multicast route entries.
G32 juniIpRouteSummaryMulticastIsisRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.3	Gauge32	read-only	The total number of Multicast IP ISIS routes.
G32 juniIpRouteSummaryMulticastLevel1IsisRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.4	Gauge32	read-only	The total number of Multicast IP Level 1 ISIS routes.
G32 juniIpRouteSummaryMulticastLevel2IsisRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.5	Gauge32	read-only	The total number of Multicast IP Level 2 ISIS routes.
G32 juniIpRouteSummaryMulticastRipRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.6	Gauge32	read-only	The total number of Multicast IP RIP routes.
G32 juniIpRouteSummaryMulticastStaticRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.7	Gauge32	read-only	The total number of Multicast IP Static routes.
G32 juniIpRouteSummaryMulticastConnectedRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.8	Gauge32	read-only	The total number of Multicast IP Connected routes.
G32 juniIpRouteSummaryMulticastBgpRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.9	Gauge32	read-only	The total number of Multicast IP BGP routes.
G32 juniIpRouteSummaryMulticastOspfRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.10	Gauge32	read-only	The total number of Multicast IP OSPF routes.
G32 juniIpRouteSummaryMulticastIntraAreaOspfRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.11	Gauge32	read-only	The total number of Multicast IP Intra Area OSPF routes.
G32 juniIpRouteSummaryMulticastInterAreaOspfRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.12	Gauge32	read-only	The total number of Multicast IP Inter Area OSPF routes.
G32 juniIpRouteSummaryMulticastExternalOspfRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.13	Gauge32	read-only	The total number of Multicast IP External OSPF routes.
G32 juniIpRouteSummaryMulticastOtherInternalRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.14	Gauge32	read-only	The total number of Multicast IP Other Internal routes.
G32 juniIpRouteSummaryMulticastAccessRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.15	Gauge32	read-only	The total number of Multicast IP Access routes.
G32 juniIpRouteSummaryMulticastIntCreatedAccessHostRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.16	Gauge32	read-only	The total number of Multicast IP Internally Created Access Host routes.
G32 juniIpRouteSummaryMultiastIntDialoutRoutes	1.3.6.1.4.1.4874.2.2.12.1.6.2.17	Gauge32	read-only	The total number of Multicast IP Internally Created Dialout routes.
G32 juniIpRouteSummaryMulticastRouteMemoryActive	1.3.6.1.4.1.4874.2.2.12.1.6.2.18	Gauge32	read-only	Multicast IP Route Memory Storage.
IP juniIpRouteSummaryMulticastLastRouteAddedOrDeletedIP	1.3.6.1.4.1.4874.2.2.12.1.6.2.19	IpAddress	read-only	IP address for last Multicast route added or deleted.
IP juniIpRouteSummaryMulticastLastRouteAddedOrDeletedMask	1.3.6.1.4.1.4874.2.2.12.1.6.2.20	IpAddress	read-only	Subnet Mask for last Multicast route added or deleted.
INT juniIpRouteSummaryMulticastLastRouteAddedOrDeletedClient	1.3.6.1.4.1.4874.2.2.12.1.6.2.21	INTEGER	read-only	Client for last Multicast route added or deleted.
OCT juniIpRouteSummaryMulticastLastRouteAddedOrDeletedDate	1.3.6.1.4.1.4874.2.2.12.1.6.2.22	OCTET STRING	read-only	Date for last Multicast route added or deleted.
juniIpTrapEnables	1.3.6.1.4.1.4874.2.2.12.2
T/F juniIpSaValidateTrapEnable	1.3.6.1.4.1.4874.2.2.12.2.1	TruthValue	read-write	Set to true to enable source address validation traps.
juniIpTraps	1.3.6.1.4.1.4874.2.2.12.3
juniIpTrapPrefix	1.3.6.1.4.1.4874.2.2.12.3.0
NTF juniIpRouteTableTrapRouteLimitExceeded	1.3.6.1.4.1.4874.2.2.12.3.0.1			The juniIpRouteTableTrapRouteLimitExceeded Trap indicates that the configured route Table Limit has been exceeded. Issued once every 5 minutes that the limit is being exceeded.
NTF juniIpRouteTableTrapRouteLimitRemove	1.3.6.1.4.1.4874.2.2.12.3.0.2			The juniIpRouteTableTrapRouteTableLimitRemove Trap indicates that routes have been freed up for 30 seconds and the Route Table Limit is no longer being violated. Issued once.
NTF juniIpRouteTableTrapWarnThresholdExceeded	1.3.6.1.4.1.4874.2.2.12.3.0.3			The juniIpRouteTableTrapWarnThresholdExceeded Trap indicates that the computed warning threshold has been exceeded. Issued once every 5 minutes that the warning threshold is being execeeded.
NTF juniIpTrapSaValidationFailure	1.3.6.1.4.1.4874.2.2.12.3.0.4			The juniIpTrapSaValidationFailure Trap indicates that a source address validation failure occurred on an interface. The interface on which the failure occurred, the source ip address and the destination ip address of the packet causing the failure are returned.
juniIpMIBNotificationObjects	1.3.6.1.4.1.4874.2.2.12.3.1
IP juniIpIfSaValFailSrcIpAddr	1.3.6.1.4.1.4874.2.2.12.3.1.1	IpAddress	accessible-for-notify	The source IP address of the packet that caused the last source address validation failure on the IP interface.
IP juniIpIfSaValFailDestIpAddr	1.3.6.1.4.1.4874.2.2.12.3.1.2	IpAddress	accessible-for-notify	The destination IP address of the packet that caused the last source address validation failure on the IP interface.
juniIpConformance	1.3.6.1.4.1.4874.2.2.12.4
juniIpCompliances	1.3.6.1.4.1.4874.2.2.12.4.1
juniIpCompliance	1.3.6.1.4.1.4874.2.2.12.4.1.1			Obsolete compliance statement for entities which implement the Juniper IP MIB. This statement became obsolete when the IP interface and IP address groups changed and the global objects were added.
juniIpCompliance2	1.3.6.1.4.1.4874.2.2.12.4.1.2			Obsolete compliance statement for entities which implement the Juniper IP MIB. This statement became obsolete when the juniIpIfAssocTable was added.
juniIpCompliance3	1.3.6.1.4.1.4874.2.2.12.4.1.3			Obsolete compliance statement for entities which implement the Juniper IP MIB. This statement became obsolete when the QoS related objects were obsoleted.
juniIpCompliance4	1.3.6.1.4.1.4874.2.2.12.4.1.4			Obsolete compliance statement for entities which implement the Juniper IP MIB. This statement became obsolete when the QoS related objects were obsoleted.
juniIpCompliance5	1.3.6.1.4.1.4874.2.2.12.4.1.5			Obsolete compliance statement for entities which implement the Juniper IP MIB. This statement became obsolete when support was added for router index and unnumbered interfaces referencing numbered interfaces.
juniIpCompliance6	1.3.6.1.4.1.4874.2.2.12.4.1.6			Obsolete compliance statement for entities which implement the Juniper IP MIB. This statement became obsolete when interface mirroring and interface auto configure support was added.
juniIpCompliance7	1.3.6.1.4.1.4874.2.2.12.4.1.7			Obsolete compliance statement for entities which implement the Juniper IP MIB. This statement became obsolete when interface TCP MSS feature was added.
juniIpCompliance8	1.3.6.1.4.1.4874.2.2.12.4.1.8			Obsolete compliance statement for entities which implement the Juniper IP MIB. This statement became obsolete when juniIpVpnIdOui and juniIpVpnIdIndex were obsoleted.
juniIpCompliance9	1.3.6.1.4.1.4874.2.2.12.4.1.9			The compliance statement for entities which implement the Juniper IP MIB.
juniIpCompliance10	1.3.6.1.4.1.4874.2.2.12.4.1.10			The compliance statement for entities which implement the Juniper IP MIB.
juniIpCompliance11	1.3.6.1.4.1.4874.2.2.12.4.1.11			The compliance statement for entities which implement the Juniper IP MIB. This statement became obsolete when juniIpVpnIdOui and juniIpVpnIdIndex were obsoleted.
juniIpCompliance12	1.3.6.1.4.1.4874.2.2.12.4.1.12			The compliance statement for entities which implement the Juniper IP MIB. This statement became obsolete when juniIpIfInitSeqPrefOper and juniIpIfInitSeqPrefAdmin were added.
juniIpCompliance13	1.3.6.1.4.1.4874.2.2.12.4.1.13			The compliance statement for entities which implement the Juniper IP MIB. This statement became obsolete when juniIpIfArpSpoofCheck was added.
juniIpCompliance14	1.3.6.1.4.1.4874.2.2.12.4.1.14			The compliance statement for entities which implement the Juniper IP MIB.
juniIpGroups	1.3.6.1.4.1.4874.2.2.12.4.2
juniIpInterfaceGroup	1.3.6.1.4.1.4874.2.2.12.4.2.1			Obsolete collection of objects for managing IP interface capabilities in a Juniper product. This group became obsolete when new objects were added to the juniIpIfTable and the juniIpIfStatsTable.
juniIpAddressGroup	1.3.6.1.4.1.4874.2.2.12.4.2.2			Obsolete collection of objects for managing IP address capabilities in a Juniper product. This group became obsolete when juniIpAdEntIgmpEnable was deprecated and juniIpAdEntIsSecondary was added.
juniIpRouteGroup	1.3.6.1.4.1.4874.2.2.12.4.2.3			Obsolete collection of objects for managing IP routing capabilities in a Juniper product. This group became obsolete when juniIpRouteLimit was obsoleted.
juniIpGlobalGroup	1.3.6.1.4.1.4874.2.2.12.4.2.4			Obsolete collection of IP global objects for managing instances of IP in a Juniper product. This group became obsolete when BGP new format objects were added.
juniIpInterfaceGroup2	1.3.6.1.4.1.4874.2.2.12.4.2.5			Obsolete collection of objects for managing IP interface capabilities in a Juniper product. This group became obsolete when the juniIpIfAssocTable was added.
juniIpAddressGroup2	1.3.6.1.4.1.4874.2.2.12.4.2.6			Obsolete collection of objects for managing IP address capabilities in a Juniper product. This group became obsolete when when juniIpArpTimeout was obsoleted.
juniIpInterfaceGroup3	1.3.6.1.4.1.4874.2.2.12.4.2.7			Obsolete collection of objects for managing IP interface capabilities in a Juniper product. This group became obsolete when the QoS related objects were obsoleted.
juniIpInterfaceGroup4	1.3.6.1.4.1.4874.2.2.12.4.2.8			Obsolete collection of objects for managing IP interface capabilities in a Juniper product. This group became obsolete when the juniIpIfInheritNum and juniIpIfInheritNumUid objects were added and juniIpIfLoopback and juniIpIfLoopbackUid were deprecated.
juniIpAddressGroup3	1.3.6.1.4.1.4874.2.2.12.4.2.9			Obsolete collection of objects for managing IP address capabilities in a Juniper product. This group became obsolete when the juniIpAdEntUnnumInheritNumIfIndex object was added and juniIpAdEntUnnumLoopbackIfIndex was deprecated.
juniIpRouteGroup2	1.3.6.1.4.1.4874.2.2.12.4.2.10			A collection of objects for managing IP routing capabilities in a Juniper product.
juniIpGlobalGroup2	1.3.6.1.4.1.4874.2.2.12.4.2.11			Obsolete collection of IP global objects for managing instances of IP in a Juniper product. This group became obsolete when juniIpVpnIdOui and juniIpVpnIdIndex were obsoleted.
juniIpInterfaceGroup5	1.3.6.1.4.1.4874.2.2.12.4.2.12			Obsolete collection of objects for managing IP interface capabilities in a Juniper product. This group became obsolete when the juniIpIfAnalyzerMode object was added.
juniIpAddressGroup4	1.3.6.1.4.1.4874.2.2.12.4.2.13			A collection of objects for managing IP address capabilities in a Juniper product.
juniIpInterfaceDeprecatedGroup	1.3.6.1.4.1.4874.2.2.12.4.2.14			A collection of deprecated objects for managing IP interface capabilities in a Juniper product. This group may continue to be support on some products.
juniIpAddressDeprecatedGroup	1.3.6.1.4.1.4874.2.2.12.4.2.15			A collection of deprecated objects for managing IP address capabilities in a Juniper product. This group may continue to be support on some products.
juniIpInterfaceGroup6	1.3.6.1.4.1.4874.2.2.12.4.2.16			Obsolete collection of objects for managing IP interface capabilities in a Juniper product. This group became obsolete when the juniIpIfTcpMss object was added.
juniIpIfSummaryGroup	1.3.6.1.4.1.4874.2.2.12.4.2.17			A collection of IP Interface Summary Statistics.
juniIpInterfaceGroup7	1.3.6.1.4.1.4874.2.2.12.4.2.18			Obsolete collection of objects for managing IP interface capabilities in a Juniper product. This group became obsolete when the juniIpIfInitSeqPrefOper and juniIpIfInitSeqPrefAdmin objects were added.
juniIpGlobalGroup3	1.3.6.1.4.1.4874.2.2.12.4.2.19			A collection of IP global objects for managing instances of IP in a Juniper product.
juniIpRouteGroup3	1.3.6.1.4.1.4874.2.2.12.4.2.20			A collection of objects for managing IP routing capabilities in a Juniper product.
juniIpNotificationGroup	1.3.6.1.4.1.4874.2.2.12.4.2.21			The management notifications pertaining to IP Route Table state changes.
juniIpNotificationGroup1	1.3.6.1.4.1.4874.2.2.12.4.2.22			The management notifications pertaining to IP.
juniIpMIBNotificationObjectsGroup	1.3.6.1.4.1.4874.2.2.12.4.2.23			The management notification objects pertaining to IP.
juniIpRouteSummaryGroup	1.3.6.1.4.1.4874.2.2.12.4.2.24			The management notifications pertaining to IP Route Table state changes.
juniIpRouteStaticBFDGroup	1.3.6.1.4.1.4874.2.2.12.4.2.25			The management notifications pertaining to IP Route Table state changes.
juniIpInterfaceGroup8	1.3.6.1.4.1.4874.2.2.12.4.2.26			A collection of objects for managing IP interface capabilities in a Juniper product.
juniIpInterfaceGroup9	1.3.6.1.4.1.4874.2.2.12.4.2.27			A collection of objects for managing IP interface capabilities in a Juniper product.

RFC description

Juniper vendor-private MIB extending IP protocol management with vendor-specific routing and forwarding objects.

Start monitoring Juniper Networks E-series broadband router (IPv4 routing/addressing) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Juniper-IP-MIB