ADTRAN-DSUDPP-MIB

All MIBs › ADTRAN-DSUDPP-MIB

Category: Vendor: ADTRAN

Description: Manages ADTRAN DSU DPP (Data Service Unit Digital Private Port) configuration and status objects.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ADTRAN-DSUDPP-MIB?

ADTRAN-DSUDPP-MIB is a vendor-specific MIB from ADTRAN covering its DSU DPP (Data Service Unit, Digital Private Port) line of telecom access devices used to terminate leased-line and private-line WAN circuits. It exposes configuration and status data for the digital private port interface, including line-level parameters and circuit status relevant to WAN connectivity. As a hardware/software status MIB it would be used to monitor the operational state of the DSU port, line alarm conditions, and configuration settings that indicate whether the unit is functioning correctly on the circuit. It likely complements standard interface (IF-MIB) and DS1/T1 line MIBs common to ADTRAN's WAN product management. It is typically deployed in enterprise or carrier WAN edge environments where ADTRAN DSU/CSU equipment terminates private-line circuits. Engineers can download the ADTRAN-DSUDPP-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ADTRAN-DSUDPP-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

ADTRAN DSU/CSU (Digital Private Port) WAN access device

Monitoring Examples

No sample objects were provided for this module, so a concrete polling scenario cannot be grounded in real object names. In practice a DSU DPP MIB of this kind would expose port status and line-configuration tables analogous to other ADTRAN DSU MIBs, letting an operator confirm the private port is in service and correctly configured, but the specific object names cannot be cited here.

What Can Be Monitored

digital private port line status
port/interface configuration
line alarm conditions
circuit operational state

Imported Objects

From ADTRAN-MIB

adProdPhysAddress

OBJECT-TYPE

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
enterprises

From RFC1213-MIB

DisplayString

OIDs

OID symbolic	OID numeric	Type	Access	Description
adDSUDP	1.3.6.1.4.1.664.1.8
adDSUDPalarm	1.3.6.1.4.1.664.2.8.5
INT adDSUDPAlarmAlert	1.3.6.1.4.1.664.2.8.5.4	INTEGER	read-only	A bit mask to select items of the AlarmStatus which represent an Alert Alarm
INT adDSUDPAlarmEnable	1.3.6.1.4.1.664.2.8.5.6	INTEGER	read-write	This bit map variable enables changes in the DSUDP Alarm Status to generate a SNMP Trap. The alarm enable bit values are: 1 0 2 0 4 0 8 Self diagnostics failed 16 OOS/OOF from network 32 DSUDP Loopback 64 Channel Loopback 128 OCU Loopback
INT adDSUDPAlarmInfo	1.3.6.1.4.1.664.2.8.5.5	INTEGER	read-only	A bit mask to select items of the AlarmStatus which represent an Info Alarm
INT adDSUDPAlarmMajor	1.3.6.1.4.1.664.2.8.5.2	INTEGER	read-only	A bit mask to select items of the AlarmStatus which represent a Major Alarm
INT adDSUDPAlarmMinor	1.3.6.1.4.1.664.2.8.5.3	INTEGER	read-only	A bit mask to select items of the AlarmStatus which represent a Minor Alarm
INT adDSUDPAlarmStatus	1.3.6.1.4.1.664.2.8.5.1	INTEGER	read-only	This bit map variable indicates changes in the DSUDP status. When a status bit changes state, the the corresponding bit is set in this variable. The alarm event bit values are: 1 No Alarm 2 0 4 0 8 Self diagnostics failed 16 OOS/OOF from network 32 DSUDP Loopback 64 Channel Loopback 128 OCU Loopback
INT adDSUDPAnswerCall	1.3.6.1.4.1.664.2.8.8.3	INTEGER	read-write	A SET answers an incoming call
INT adDSUDPAutoAnswer	1.3.6.1.4.1.664.2.8.3.4.11	INTEGER	read-write	Enables/Disables automatic answer of incoming calls
adDSUDPcall	1.3.6.1.4.1.664.2.8.8
NTF adDSUDPchannelLoopback	1.3.6.1.4.1.664.1.8.0.813			The Channel Loopback test is active.
NTF adDSUDPchannelLoopbackClear	1.3.6.1.4.1.664.1.8.0.812			The Channel Loopback test cleared.
INT adDSUDPDialStored	1.3.6.1.4.1.664.2.8.8.1	INTEGER	read-write	Dials the stored number in register 1-10
STR adDSUDPDialStored1	1.3.6.1.4.1.664.2.8.3.4.1	DisplayString	read-write	Edit or View stored Dial Location 1
STR adDSUDPDialStored10	1.3.6.1.4.1.664.2.8.3.4.10	DisplayString	read-write	Edit or View stored Dial Location 10
STR adDSUDPDialStored2	1.3.6.1.4.1.664.2.8.3.4.2	DisplayString	read-write	Edit or View stored Dial Location 2
STR adDSUDPDialStored3	1.3.6.1.4.1.664.2.8.3.4.3	DisplayString	read-write	Edit or View stored Dial Location 3
STR adDSUDPDialStored4	1.3.6.1.4.1.664.2.8.3.4.4	DisplayString	read-write	Edit or View stored Dial Location 4
STR adDSUDPDialStored5	1.3.6.1.4.1.664.2.8.3.4.5	DisplayString	read-write	Edit or View stored Dial Location 5
STR adDSUDPDialStored6	1.3.6.1.4.1.664.2.8.3.4.6	DisplayString	read-write	Edit or View stored Dial Location 6
STR adDSUDPDialStored7	1.3.6.1.4.1.664.2.8.3.4.7	DisplayString	read-write	Edit or View stored Dial Location 7
STR adDSUDPDialStored8	1.3.6.1.4.1.664.2.8.3.4.8	DisplayString	read-write	Edit or View stored Dial Location 8
STR adDSUDPDialStored9	1.3.6.1.4.1.664.2.8.3.4.9	DisplayString	read-write	Edit or View stored Dial Location 9
INT adDSUDPds0AlertEnable	1.3.6.1.4.1.664.2.8.4.6.1.3	INTEGER	read-write	This bit map variable enables changes in the DS0 PM Alert Status to generate a SNMP Trap. The alert enable bit values are: 1 Interval UAS 2 Daily UAS 4 Daily percent Availability
adDSUDPds0AlertEntry	1.3.6.1.4.1.664.2.8.4.6.1		not-accessible	An entry in the DS0 PM Alert Table
INT adDSUDPds0AlertIndex	1.3.6.1.4.1.664.2.8.4.6.1.1	INTEGER	read-only	The index value which uniquely identifies the DS0 PM interface to which this entry is applicable.
INT adDSUDPds0AlertStatus	1.3.6.1.4.1.664.2.8.4.6.1.2	INTEGER	read-only	This bit map variable indicates Threshold Crossing Events for DS0 performance monitored parameters. When a parameter exceeds its threshold value, the parameter's bit is set in this variable. A SNMP trap is generated if the parameter's alert enable bit is set. The alert event bit values are: 1 Interval UAS 2 Daily UAS 4 Daily percent Availability
adDSUDPds0AlertTable	1.3.6.1.4.1.664.2.8.4.6		not-accessible	The DS0 Performance Monitor Alert Table
INT adDSUDPds0DailyAvail	1.3.6.1.4.1.664.2.8.4.3.1.4	INTEGER	read-only	The percentage (times 100) of channel availability encountered by a DS0 interface in one of the 7 Daily Intervals.
INT adDSUDPds0DailyAvgAvail	1.3.6.1.4.1.664.2.8.4.3.1.5	INTEGER	read-only	The percentage (times 100) of channel availability averaged over the last 7 days
adDSUDPds0DailyEntry	1.3.6.1.4.1.664.2.8.4.3.1		not-accessible	An entry in the DS0 Daily table.
INT adDSUDPds0DailyIndex	1.3.6.1.4.1.664.2.8.4.3.1.1	INTEGER	read-only	The index value which uniquely identifies the DS0 interface to which this entry is applicable.
INT adDSUDPds0DailyNumber	1.3.6.1.4.1.664.2.8.4.3.1.2	INTEGER	read-only	A number between 1 and 7, where 1 is the current accumulating Daily Interval and 2-7 are the completed Daily Intervals. 2 is the most recent completed Daily Interval and 7 is the least recent completed Daily Interval (assuming that all 7 Daily Intervals are valid).
adDSUDPds0DailyTable	1.3.6.1.4.1.664.2.8.4.3		not-accessible	The DS0 Daily table.
INT adDSUDPds0DailyThrsAvail	1.3.6.1.4.1.664.2.8.4.5.1.3	INTEGER	read-write	The DS0 performance monitor Threshold Value for the percentage channel Availability parameter. The default value is 9950 (% times 100), which equates to 99.5% Availability for a Daily Interval.
adDSUDPds0DailyThrsEntry	1.3.6.1.4.1.664.2.8.4.5.1		not-accessible	An entry in the DS0 Threshold Table.
INT adDSUDPds0DailyThrsIndex	1.3.6.1.4.1.664.2.8.4.5.1.1	INTEGER	read-only	The index value which uniquely identifies the DS0 interface to which this entry is applicable.
adDSUDPds0DailyThrsTable	1.3.6.1.4.1.664.2.8.4.5		not-accessible	The DS0 Daily Threshold Table.
INT adDSUDPds0DailyThrsUASs	1.3.6.1.4.1.664.2.8.4.5.1.2	INTEGER	read-write	The DS0 performance monitor Threshold Value for the Daily Unavailable Seconds parameter. The default value is 86, which equates to approximately 99.9% Availability for a Daily Interval.
CTR adDSUDPds0DailyUASs	1.3.6.1.4.1.664.2.8.4.3.1.3	Counter	read-only	The number of Unavailable Seconds encountered by a DS0 interface in one of the 7 Daily Intervals.
adDSUDPds0IntervalEntry	1.3.6.1.4.1.664.2.8.4.2.1		not-accessible	An entry in the DS0 Interval Table.
INT adDSUDPds0IntervalIndex	1.3.6.1.4.1.664.2.8.4.2.1.1	INTEGER	read-only	The index value which uniquely identifies the DS0 interface to which this entry is applicable.
INT adDSUDPds0IntervalNumber	1.3.6.1.4.1.664.2.8.4.2.1.2	INTEGER	read-only	A number between 1 and 97, where 1 is the current accumulating 15 minute interval and 2-97 are completed 15 minute intervals. 2 is the most recent completed interval and 97 is the least recent completed 15 minute interval (assuming that all 97 intervals are valid).
adDSUDPds0IntervalTable	1.3.6.1.4.1.664.2.8.4.2		not-accessible	The DS0 Interval Table.
adDSUDPds0IntervalThrsEntry	1.3.6.1.4.1.664.2.8.4.4.1		not-accessible	An entry in the DS0 Threshold Table.
INT adDSUDPds0IntervalThrsIndex	1.3.6.1.4.1.664.2.8.4.4.1.1	INTEGER	read-only	The index value which uniquely identifies the DS0 interface to which this entry is applicable.
adDSUDPds0IntervalThrsTable	1.3.6.1.4.1.664.2.8.4.4		not-accessible	The DS0 Interval Threshold Table.
INT adDSUDPds0IntervalThrsUASs	1.3.6.1.4.1.664.2.8.4.4.1.2	INTEGER	read-write	The DS0 performance monitor Threshold Value for the 15 minute Unavailable Seconds parameter. The default value is 1, which equates to approximately 99.9% Availability for a 15 minute Interval.
CTR adDSUDPds0IntervalUASs	1.3.6.1.4.1.664.2.8.4.2.1.3	Counter	read-only	The number of Unavailable Seconds encountered by a DS0 interface in one of the 97, individual 15 minute, intervals.
NTF adDSUDPdsuLoopback	1.3.6.1.4.1.664.1.8.0.811			The DSU Loopback test is active.
NTF adDSUDPdsuLoopbackClear	1.3.6.1.4.1.664.1.8.0.810			The DSU Loopback test condition cleared.
INT adDSUDPdteAntiStream	1.3.6.1.4.1.664.2.8.3.2.7	INTEGER	read-write	Configures DTE Anti-Streaming Disconnect
INT adDSUDPdteCDOptions	1.3.6.1.4.1.664.2.8.3.2.8	INTEGER	read-write	Configures CD signal lead on primary DTE
INT adDSUDPdteCSOptions	1.3.6.1.4.1.664.2.8.3.2.6	INTEGER	read-write	Configures CS signal lead on primary DTE
INT adDSUDPdteFormat	1.3.6.1.4.1.664.2.8.3.2.2	INTEGER	read-write	Selects DTE data format
INT adDSUDPdteInBandCommand	1.3.6.1.4.1.664.2.8.3.2.4	INTEGER	read-write	Selects DTE in-band command type
INT adDSUDPdteRate	1.3.6.1.4.1.664.2.8.3.2.1	INTEGER	read-write	Selects bit rate of primary DTE
INT adDSUDPdteRSCSDelay	1.3.6.1.4.1.664.2.8.3.2.11	INTEGER	read-write	Configures DTE signals RS-CS delay
INT adDSUDPdteSROptions	1.3.6.1.4.1.664.2.8.3.2.10	INTEGER	read-write	Configures SR signal lead to primary DTE
INT adDSUDPdteTROptions	1.3.6.1.4.1.664.2.8.3.2.9	INTEGER	read-write	Configures handling of TR lead from Primary DTE
INT adDSUDPdteTxClock	1.3.6.1.4.1.664.2.8.3.2.5	INTEGER	read-write	Selects transmit timing source
INT adDSUDPdteWordLength	1.3.6.1.4.1.664.2.8.3.2.3	INTEGER	read-write	Selects DTE asynchronous word length
INT adDSUDPHangUp	1.3.6.1.4.1.664.2.8.8.4	INTEGER	read-write	A SET commands the DSUDP to go on-hook
INT adDSUDPInjectError	1.3.6.1.4.1.664.2.8.6.7	INTEGER	read-write	SET injects one error into active test pattern
INT adDSUDPLedStatus	1.3.6.1.4.1.664.2.8.7.4	INTEGER	read-only	This variable contains bit encoded values for LED status (0=off, 1=on): 1 IDL 2 ALM 4 TST 8 ERR
STR adDSUDPManualDial	1.3.6.1.4.1.664.2.8.8.2	DisplayString	read-write	A SET dials the input command string
adDSUDPmg	1.3.6.1.4.1.664.2.8
INT adDSUDPMode	1.3.6.1.4.1.664.2.8.7.3	INTEGER	read-only	Current mode of DSUDP
INT adDSUDPnetLoopRate	1.3.6.1.4.1.664.2.8.3.1.1	INTEGER	read-write	Indicates the DS0 loop data rate
INT adDSUDPnetRemoteCfg	1.3.6.1.4.1.664.2.8.3.1.4	INTEGER	read-write	Enables/Disables configuration by a remote DSUDP
INT adDSUDPnetScrambler	1.3.6.1.4.1.664.2.8.3.1.3	INTEGER	read-write	Disables/Enables Scrambling
INT adDSUDPnetType	1.3.6.1.4.1.664.2.8.3.1.2	INTEGER	read-write	Selects the network type
NTF adDSUDPNetworkINS	1.3.6.1.4.1.664.1.8.0.808			The network channel is In-Service. The OOS/OOF condition has cleared.
NTF adDSUDPNetworkOOS	1.3.6.1.4.1.664.1.8.0.809			The network channel is in an Out-Of-Service state.
NTF adDSUDPocuLoopback	1.3.6.1.4.1.664.1.8.0.815			The OCU Loopback test is active.
NTF adDSUDPocuLoopbackClear	1.3.6.1.4.1.664.1.8.0.814			The OCU Loopback test cleared.
adDSUDPperform	1.3.6.1.4.1.664.2.8.4
adDSUDPprov	1.3.6.1.4.1.664.2.8.3
adDSUDPprovDial	1.3.6.1.4.1.664.2.8.3.4
adDSUDPprovDte	1.3.6.1.4.1.664.2.8.3.2
adDSUDPprovNet	1.3.6.1.4.1.664.2.8.3.1
adDSUDPprovTest	1.3.6.1.4.1.664.2.8.3.3
INT adDSUDPSelfDiagnostics	1.3.6.1.4.1.664.2.8.6.5	INTEGER	read-only	Current Self Test status
NTF adDSUDPSelfTestFail	1.3.6.1.4.1.664.1.8.0.807			The DSUDP Self Diagnostics Failed
NTF adDSUDPSelfTestPass	1.3.6.1.4.1.664.1.8.0.806			The DSUDP Self Diagnostics Passed.
adDSUDPstatus	1.3.6.1.4.1.664.2.8.7
INT adDSUDPStatusConnector	1.3.6.1.4.1.664.2.8.7.2	INTEGER	read-only	The jumper selected DTE interface connector on DSUDP
INT adDSUDPStatusEIA	1.3.6.1.4.1.664.2.8.7.1	INTEGER	read-only	Bit map status of Primay DTE EIA interface signals (off = 0, on = 1), where bit positions are: 1 RI 2 RD 4 SD 8 CD 16 CS 32 RS 64 SR 128 TR
adDSUDPtest	1.3.6.1.4.1.664.2.8.6
INT adDSUDPTestCmd	1.3.6.1.4.1.664.2.8.6.1	INTEGER	read-write	A SET performs the selected test
INT adDSUDPTestErrors	1.3.6.1.4.1.664.2.8.6.3	INTEGER	read-write	This variable accumulates errors for the active test pattern. A SET operation will clear the error count.
INT adDSUDPtestRdlCfg	1.3.6.1.4.1.664.2.8.3.3.2	INTEGER	read-write	Enables/Disables response to Remote Digital Loopback
INT adDSUDPTestRxPattern	1.3.6.1.4.1.664.2.8.6.4	INTEGER	read-only	Receive test pattern status
INT adDSUDPTestStatus	1.3.6.1.4.1.664.2.8.6.2	INTEGER	read-only	Current test status
INT adDSUDPtestTimeout	1.3.6.1.4.1.664.2.8.3.3.1	INTEGER	read-write	Configures test timeout in seconds
INT adDSUDPTestTxPattern	1.3.6.1.4.1.664.2.8.6.6	INTEGER	read-write	SETs default transmit test pattern
NTF adDSUDPThrsAlertDailyAvail	1.3.6.1.4.1.664.1.8.0.875			The daily percent channel availability has reached or dropped below its threshold value.
NTF adDSUDPThrsAlertDailyUAS	1.3.6.1.4.1.664.1.8.0.867			The Daily Un-Available Seconds UAS parameter has reached or exceeds its threshold value.
NTF adDSUDPThrsAlertIntUAS	1.3.6.1.4.1.664.1.8.0.883			The Interval Un-Available Seconds (UAS) parameter has reached or exceeds its threshold value.
adMgmt	1.3.6.1.4.1.664.2
adProducts	1.3.6.1.4.1.664.1
adtran	1.3.6.1.4.1.664

RFC description

Manages ADTRAN DSUDP Plus data service units including provisioning, performance, alarms, and network configuration.

Start monitoring ADTRAN DSU DPP data service units (legacy) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ADTRAN-DSUDPP-MIB

What Is ADTRAN-DSUDPP-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description