All MIBs › ZXR10-SWITCH-MIB
Category: ZTE ZXR10 Layer 2 Switching
Description: Manages ZTE ZXR10 switch-level configuration including port settings, VLAN membership, and switch fabric status.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is ZXR10-SWITCH-MIB?
ZXR10-SWITCH-MIB is a ZTE enterprise MIB implementing switch-level configuration and status management for the ZXR10 switch product family, rooted under zte.zxr10.zxr10switch (enterprises.3902.3.102). It defines VLAN management via zxr10CpuVlanPvidTable (per-VLAN ID, MTU, state, SAID, VPN ID, member port bitmaps), tagged/untagged VLAN membership tables (zxr10CpuVlanTagTable, zxr10CpuVlanUntagTable), and IGMP snooping control through zxr10IgmpSnoopingTable, alongside dedicated subtrees for QinQ tagging, loop detection, VCT cable diagnostics, super-VLANs (svlan), and DHCP snooping. These objects expose the switch's Layer 2 forwarding and multicast-snooping configuration state, useful for confirming VLAN provisioning, membership, and IGMP snooping status are consistent with intended network design. It is deployed alongside standard bridge and interface MIBs (ifIndex from RFC1213-MIB is imported directly) on ZXR10 switch hardware in ZTE-based access and aggregation networks. Engineers standing up ZTE gear commonly pull a ZXR10-SWITCH-MIB MIB Browser view first to map out the vendor's VLAN and IGMP snooping object tree.
IPNetwork Monitor allows you to monitor SNMP objects defined in ZXR10-SWITCH-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- ZTE ZXR10 switch series
Monitoring Examples
An operator polls zxr10CpuVlanPvidTable's zxr10CpuVlanState and zxr10CpuVlanMemPortsPvid to confirm a VLAN is active and has the expected port membership, then checks zxr10IgmpSnoopingTable's zxr10igmpSnoopingDropEnable and zxr10igmpSnoopingMaxHostNum for that VLAN; an unexpectedly disabled VLAN state or a full host table would explain multicast traffic not reaching expected receivers.
What Can Be Monitored
- VLAN PVID/state/membership table entries
- tagged and untagged VLAN membership
- IGMP snooping group and host-limit configuration
- QinQ and super-VLAN configuration
- loop-detection and VCT cable-diagnostic subtrees
This MIB depends on
Related MIBs
Imported Objects
From RFC1155-SMI
| Counter | |
| Gauge | |
| IpAddress | |
| NetworkAddress | |
| mgmt |
From RFC1213-MIB
| ifIndex |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| NOTIFICATION-GROUP | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| MODULE-IDENTITY | |
| NOTIFICATION-TYPE | |
| OBJECT-TYPE | |
| Unsigned32 | |
| enterprises | |
| experimental |
From SNMPv2-TC
| MacAddress | |
| RowStatus |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| zte | 1.3.6.1.4.1.3902 | |||
| zxr10 | 1.3.6.1.4.1.3902.3 | |||
| zxr10switch | 1.3.6.1.4.1.3902.3.102 | |||
| zxr10vlan | 1.3.6.1.4.1.3902.3.102.1 | |||
| zxr10CpuVlanPvidTable | 1.3.6.1.4.1.3902.3.102.1.1 | not-accessible | vlan information table. | |
| zxr10CpuVlanPvidEntry | 1.3.6.1.4.1.3902.3.102.1.1.1 | not-accessible | ||
| I32 zxr10CpuVlanIf | 1.3.6.1.4.1.3902.3.102.1.1.1.2 | Integer32 | read-only | The vlan entry -> L3 interface |
| I32 zxr10CpuVlanMtu | 1.3.6.1.4.1.3902.3.102.1.1.1.3 | Integer32 | read-only | vlan MTU size |
| INT zxr10CpuVlanState | 1.3.6.1.4.1.3902.3.102.1.1.1.4 | INTEGER | read-only | vlan state:active or suspend |
| I32 zxr10CpuVlanSaid | 1.3.6.1.4.1.3902.3.102.1.1.1.5 | Integer32 | read-only | Security Association Identifier(SAID) |
| ROW zxr10CpuVlanRowStatus | 1.3.6.1.4.1.3902.3.102.1.1.1.7 | RowStatus | read-create | creat or delete vlan |
| STR zxr10CpuVlanMemPortsPvid | 1.3.6.1.4.1.3902.3.102.1.1.1.9 | DisplayString | read-write | pvid of port members |
| zxr10CpuVlanTagTable | 1.3.6.1.4.1.3902.3.102.1.2 | not-accessible | vlan information table. | |
| zxr10CpuVlanTagEntry | 1.3.6.1.4.1.3902.3.102.1.2.1 | not-accessible | ||
| I32 zxr10CpuVlanVpnid | 1.3.6.1.4.1.3902.3.102.1.2.1.2 | Integer32 | read-only | The vlan entry -> Vpnid |
| STR zxr10CpuVlanMemPortsTag | 1.3.6.1.4.1.3902.3.102.1.2.1.4 | DisplayString | read-write | tag port members |
| zxr10QinQ | 1.3.6.1.4.1.3902.3.102.1.3 | |||
| zxr10QinQTable | 1.3.6.1.4.1.3902.3.102.1.3.1 | not-accessible | switchport qinq(802.1q in 802.1q) configuration table. | |
| zxr10QinQEntry | 1.3.6.1.4.1.3902.3.102.1.3.1.1 | not-accessible | ||
| STR zxr10QinQPortName | 1.3.6.1.4.1.3902.3.102.1.3.1.1.1 | DisplayString | read-only | Name of this port |
| INT zxr10QinQMode | 1.3.6.1.4.1.3902.3.102.1.3.1.1.2 | INTEGER | read-write | The qinq mode of switchport |
| I32 zxr10QinQTpid | 1.3.6.1.4.1.3902.3.102.1.3.1.1.3 | Integer32 | read-write | The qinq tpid of switchport |
| I32 zxr10QinQPvid | 1.3.6.1.4.1.3902.3.102.1.3.1.1.4 | Integer32 | read-only | The native vlan id of switchport |
| I32 zxr10QinQExtendTpid | 1.3.6.1.4.1.3902.3.102.1.3.2 | Integer32 | read-write | The extend qinq tpid |
| I32 zxr10QinQStandardTpid | 1.3.6.1.4.1.3902.3.102.1.3.3 | Integer32 | read-write | The standard qinq tpid |
| zxr10MemberShip | 1.3.6.1.4.1.3902.3.102.1.4 | |||
| zxr10MemberShipTable | 1.3.6.1.4.1.3902.3.102.1.4.1 | not-accessible | vlan membership information table. | |
| zxr10MemberShipEntry | 1.3.6.1.4.1.3902.3.102.1.4.1.1 | not-accessible | ||
| STR zxr10MemberShipPortName | 1.3.6.1.4.1.3902.3.102.1.4.1.1.1 | DisplayString | read-only | Name of this port |
| I32 zxr10MemberShipPvid | 1.3.6.1.4.1.3902.3.102.1.4.1.1.2 | Integer32 | read-write | The native vlan id of this interface |
| INT zxr10MemberShipMode | 1.3.6.1.4.1.3902.3.102.1.4.1.1.3 | INTEGER | read-write | Vlan mode of this interface. |
| OCT zxr10MemberShipVlansTag | 1.3.6.1.4.1.3902.3.102.1.4.1.1.4 | OCTET STRING | read-write | vlan tag bitMap (1-1023) |
| OCT zxr10MemberShipVlansHybridUnTag | 1.3.6.1.4.1.3902.3.102.1.4.1.1.5 | OCTET STRING | read-write | vlan untag bitMap(1-1023) of hybrid ports |
| OCT zxr10MemberShipVlansTag2k | 1.3.6.1.4.1.3902.3.102.1.4.1.1.6 | OCTET STRING | read-write | vlan bitMap (1024-2047) |
| OCT zxr10MemberShipVlansHybridUnTag2k | 1.3.6.1.4.1.3902.3.102.1.4.1.1.7 | OCTET STRING | read-write | vlan untag bitMap(1024-2047) of hybrid ports |
| OCT zxr10MemberShipVlansTag3k | 1.3.6.1.4.1.3902.3.102.1.4.1.1.8 | OCTET STRING | read-write | vlan tag bitMap (2048-3071) |
| OCT zxr10MemberShipVlansHybridUnTag3k | 1.3.6.1.4.1.3902.3.102.1.4.1.1.9 | OCTET STRING | read-write | vlan untag bitMap(2048-3071) of hybrid ports |
| OCT zxr10MemberShipVlansTag4k | 1.3.6.1.4.1.3902.3.102.1.4.1.1.10 | OCTET STRING | read-write | vlan tag bitMap (3072-4094) |
| OCT zxr10MemberShipVlansHybridUnTag4k | 1.3.6.1.4.1.3902.3.102.1.4.1.1.11 | OCTET STRING | read-write | vlan untag bitMap(3072-4094) of hybrid ports |
| zxr10CpuVlanUntagTable | 1.3.6.1.4.1.3902.3.102.1.5 | not-accessible | vlan information table. | |
| zxr10CpuVlanUntagEntry | 1.3.6.1.4.1.3902.3.102.1.5.1 | not-accessible | ||
| I32 zxr10CpuVlanId | 1.3.6.1.4.1.3902.3.102.1.5.1.1 | Integer32 | read-only | The vlan id (1-4094) |
| STR zxr10CpuVlanName | 1.3.6.1.4.1.3902.3.102.1.5.1.3 | DisplayString | read-write | vlan name |
| STR zxr10CpuVlanMemPortsUntag | 1.3.6.1.4.1.3902.3.102.1.5.1.4 | DisplayString | read-write | pvid of port members |
| zxr10igmpSnooping | 1.3.6.1.4.1.3902.3.102.5 | |||
| zxr10IgmpSnoopingTable | 1.3.6.1.4.1.3902.3.102.5.1 | not-accessible | ZXR10 igmp snooping table. | |
| zxr10IgmpSnoopingEntry | 1.3.6.1.4.1.3902.3.102.5.1.1 | not-accessible | zxr10 Igmp Snooping Entry | |
| INT zxr10igmpSnoopingValid | 1.3.6.1.4.1.3902.3.102.5.1.1.1 | INTEGER | read-only | 0 is invalid,1 is valid. |
| I32 zxr10igmpSnoopingVlanId | 1.3.6.1.4.1.3902.3.102.5.1.1.2 | Integer32 | read-only | ZXR10 igmp snooping Vlan Id |
| I32 zxr10igmpSnoopingGroupId | 1.3.6.1.4.1.3902.3.102.5.1.1.3 | Integer32 | read-only | zxr10 Igmp Snooping Entry |
| INT zxr10igmpSnoopingDropEnable | 1.3.6.1.4.1.3902.3.102.5.1.1.4 | INTEGER | read-only | Enabled/Disables IGMP Multicast. |
| I32 zxr10igmpSnoopingMaxHostNum | 1.3.6.1.4.1.3902.3.102.5.1.1.5 | Integer32 | read-only | MAX hosts can access in this group. |
| IP zxr10igmpSnoopingIpAddr | 1.3.6.1.4.1.3902.3.102.5.1.1.6 | IpAddress | read-only | ZXR10 igmp snooping Ip Addr |
| MAC zxr10igmpSnoopingGroupMac | 1.3.6.1.4.1.3902.3.102.5.1.1.7 | MacAddress | read-only | ZXR10 igmp snooping Group Mac |
| OCT zxr10igmpSnoopingMemPorts0 | 1.3.6.1.4.1.3902.3.102.5.1.1.8 | OCTET STRING | read-only | ZXR10 igmp snooping MemPorts 0 |
| OCT zxr10igmpSnoopingMemPorts1 | 1.3.6.1.4.1.3902.3.102.5.1.1.9 | OCTET STRING | read-only | ZXR10 igmp snooping MemPorts 1 |
| OCT zxr10igmpSnoopingMemPorts2 | 1.3.6.1.4.1.3902.3.102.5.1.1.10 | OCTET STRING | read-only | ZXR10 igmp snooping MemPorts 2 |
| OCT zxr10igmpSnoopingMemPorts3 | 1.3.6.1.4.1.3902.3.102.5.1.1.11 | OCTET STRING | read-only | ZXR10 igmp snooping MemPorts 3 |
| OCT zxr10igmpSnoopingMemPorts4 | 1.3.6.1.4.1.3902.3.102.5.1.1.12 | OCTET STRING | read-only | ZXR10 igmp snooping MemPorts 4 |
| OCT zxr10igmpSnoopingMemPorts5 | 1.3.6.1.4.1.3902.3.102.5.1.1.13 | OCTET STRING | read-only | ZXR10 igmp snooping MemPorts 5 |
| OCT zxr10igmpSnoopingMemPorts6 | 1.3.6.1.4.1.3902.3.102.5.1.1.14 | OCTET STRING | read-only | ZXR10 igmp snooping MemPorts 6 |
| OCT zxr10igmpSnoopingMemPorts7 | 1.3.6.1.4.1.3902.3.102.5.1.1.15 | OCTET STRING | read-only | ZXR10 igmp snooping MemPorts 7 |
| OCT zxr10igmpSnoopingMemPorts8 | 1.3.6.1.4.1.3902.3.102.5.1.1.16 | OCTET STRING | read-only | ZXR10 igmp snooping MemPorts 8 |
| OCT zxr10igmpSnoopingMemPorts9 | 1.3.6.1.4.1.3902.3.102.5.1.1.17 | OCTET STRING | read-only | ZXR10 igmp snooping MemPorts 9 |
| OCT zxr10igmpSnoopingMemPorts10 | 1.3.6.1.4.1.3902.3.102.5.1.1.18 | OCTET STRING | read-only | ZXR10 igmp snooping MemPorts 10 |
| OCT zxr10igmpSnoopingMemPorts11 | 1.3.6.1.4.1.3902.3.102.5.1.1.19 | OCTET STRING | read-only | ZXR10 igmp snooping MemPorts 11 |
| OCT zxr10igmpSnoopingMemPorts12 | 1.3.6.1.4.1.3902.3.102.5.1.1.20 | OCTET STRING | read-only | ZXR10 igmp snooping MemPorts 12 |
| OCT zxr10pimSnoopingMemPorts0 | 1.3.6.1.4.1.3902.3.102.5.1.1.31 | OCTET STRING | read-only | zxr10 pim Snooping MemPorts 0 |
| OCT zxr10pimSnoopingMemPorts1 | 1.3.6.1.4.1.3902.3.102.5.1.1.32 | OCTET STRING | read-only | zxr10 pim Snooping MemPorts 1 |
| OCT zxr10pimSnoopingMemPorts2 | 1.3.6.1.4.1.3902.3.102.5.1.1.33 | OCTET STRING | read-only | zxr10 pim Snooping MemPorts 2 |
| OCT zxr10pimSnoopingMemPorts3 | 1.3.6.1.4.1.3902.3.102.5.1.1.34 | OCTET STRING | read-only | zxr10 pim Snooping MemPorts 3 |
| OCT zxr10pimSnoopingMemPorts4 | 1.3.6.1.4.1.3902.3.102.5.1.1.35 | OCTET STRING | read-only | zxr10 pim Snooping MemPorts 4 |
| OCT zxr10pimSnoopingMemPorts5 | 1.3.6.1.4.1.3902.3.102.5.1.1.36 | OCTET STRING | read-only | zxr10 pim Snooping MemPorts 5 |
| OCT zxr10pimSnoopingMemPorts6 | 1.3.6.1.4.1.3902.3.102.5.1.1.37 | OCTET STRING | read-only | zxr10 pim Snooping MemPorts 6 |
| OCT zxr10pimSnoopingMemPorts7 | 1.3.6.1.4.1.3902.3.102.5.1.1.38 | OCTET STRING | read-only | zxr10 pim Snooping MemPorts 7 |
| OCT zxr10pimSnoopingMemPorts8 | 1.3.6.1.4.1.3902.3.102.5.1.1.39 | OCTET STRING | read-only | zxr10 pim Snooping MemPorts 8 |
| OCT zxr10pimSnoopingMemPorts9 | 1.3.6.1.4.1.3902.3.102.5.1.1.40 | OCTET STRING | read-only | zxr10 pim Snooping MemPorts 9 |
| OCT zxr10pimSnoopingMemPorts10 | 1.3.6.1.4.1.3902.3.102.5.1.1.41 | OCTET STRING | read-only | zxr10 pim Snooping MemPorts 10 |
| OCT zxr10pimSnoopingMemPorts11 | 1.3.6.1.4.1.3902.3.102.5.1.1.42 | OCTET STRING | read-only | zxr10 pim Snooping MemPorts 11 |
| OCT zxr10pimSnoopingMemPorts12 | 1.3.6.1.4.1.3902.3.102.5.1.1.43 | OCTET STRING | read-only | zxr10 pim Snooping MemPorts 12 |
| zxr10PimSnoopingNeighborTable | 1.3.6.1.4.1.3902.3.102.5.2 | not-accessible | ZXR10 pim snooping neighbor table. | |
| zxr10PimSnoopingNeighborEntry | 1.3.6.1.4.1.3902.3.102.5.2.1 | not-accessible | zxr10 Pim Snooping Neighbor Entry | |
| INT zxr10pimSnoopingNeighborValid | 1.3.6.1.4.1.3902.3.102.5.2.1.1 | INTEGER | read-only | 0 is invalid,1 is valid. |
| I32 zxr10pimSnoopingNeighborVlanId | 1.3.6.1.4.1.3902.3.102.5.2.1.2 | Integer32 | read-only | zxr10 pim Snooping Neighbor Vlan Id |
| I32 zxr10pimSnoopingNeighborVpnId | 1.3.6.1.4.1.3902.3.102.5.2.1.3 | Integer32 | read-only | zxr10 pim Snooping Neighbor Vpn Id |
| I32 zxr10pimSnoopingNeighborId | 1.3.6.1.4.1.3902.3.102.5.2.1.4 | Integer32 | read-only | zxr10 pim Snooping Neighbor Id |
| IP zxr10pimSnoopingNeighborSourceIpAddr | 1.3.6.1.4.1.3902.3.102.5.2.1.5 | IpAddress | read-only | zxr10 pim Snooping Neighbor Source Ip Addr |
| OCT zxr10pimSnoopingNeighborPort | 1.3.6.1.4.1.3902.3.102.5.2.1.6 | OCTET STRING | read-only | zxr10 pim Snooping Neighbor Port |
| zxr10IgmpSnoopingVlanTable | 1.3.6.1.4.1.3902.3.102.5.3 | not-accessible | ZXR10 igmp snooping vlan table. | |
| zxr10IgmpSnoopingVlanEntry | 1.3.6.1.4.1.3902.3.102.5.3.1 | not-accessible | zxr10 Igmp Snooping Vlan Entry | |
| I32 zxr10igmpSnoopingVlanEntryVlanId | 1.3.6.1.4.1.3902.3.102.5.3.1.1 | Integer32 | read-only | zxr10 igmp Snooping Vlan Entry Vlan Id |
| INT zxr10igmpSnoopingVlanEntryEnable | 1.3.6.1.4.1.3902.3.102.5.3.1.2 | INTEGER | read-only | Enables/disables IGMP Snooping on this vlan |
| INT zxr10pimSnoopingVlanEntryEnable | 1.3.6.1.4.1.3902.3.102.5.3.1.3 | INTEGER | read-only | Enables/disables PIM Snooping on this vlan |
| INT zxr10igmpSnoopingFastLeave | 1.3.6.1.4.1.3902.3.102.5.3.1.4 | INTEGER | read-only | Enables/disables group membership fast leave |
| I32 zxr10igmpSnoopingLastMemberQueryInterval | 1.3.6.1.4.1.3902.3.102.5.3.1.5 | Integer32 | read-only | The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages. |
| I32 zxr10igmpSnoopingMaxGroupNum | 1.3.6.1.4.1.3902.3.102.5.3.1.6 | Integer32 | read-only | MAX multicast groups can access in this vlan |
| I32 zxr10igmpSnoopingGroupNum | 1.3.6.1.4.1.3902.3.102.5.3.1.7 | Integer32 | read-only | Number of multicast groups access in this vlan currently |
| I32 zxr10igmpSnoopingHostTimeOut | 1.3.6.1.4.1.3902.3.102.5.3.1.8 | Integer32 | read-only | Host aging-time |
| I32 zxr10igmpSnoopingMrTimeOut | 1.3.6.1.4.1.3902.3.102.5.3.1.9 | Integer32 | read-only | Router aging-time |
| INT zxr10igmpSnoopingEnable | 1.3.6.1.4.1.3902.3.102.5.4 | INTEGER | read-only | Enables/disables IGMP Snooping on this device |
| INT zxr10pimSnoopingEnable | 1.3.6.1.4.1.3902.3.102.5.5 | INTEGER | read-only | Enables/disables PIM Snooping on this device |
| INT zxr10igmpSnoopingGlobalQuery | 1.3.6.1.4.1.3902.3.102.5.6 | INTEGER | read-only | Enabled/Disables IGMP Queries for this device |
| I32 zxr10igmpSnoopingQueryInterval | 1.3.6.1.4.1.3902.3.102.5.7 | Integer32 | read-only | The Query Interval is the interval between General Queries sent by the Querier. Default: 125 seconds. |
| I32 zxr10igmpSnoopingQueryResponseInterval | 1.3.6.1.4.1.3902.3.102.5.8 | Integer32 | read-only | The Max Response Time inserted into the periodic General Queries |
| zxr10extAlarm | 1.3.6.1.4.1.3902.3.102.6 | |||
| zxr10InputAlarmTable | 1.3.6.1.4.1.3902.3.102.6.1 | not-accessible | the table of input alarm. | |
| zxr10InputAlarmEntry | 1.3.6.1.4.1.3902.3.102.6.1.1 | not-accessible | the table of input alarm. | |
| INT zxr10InputAlarmIndex | 1.3.6.1.4.1.3902.3.102.6.1.1.1 | INTEGER | read-only | the type of alarm. |
| INT zxr10InputAlarmStatus | 1.3.6.1.4.1.3902.3.102.6.1.1.2 | INTEGER | read-only | the status of alarm. |
| STR zxr10InputAlarmDescription | 1.3.6.1.4.1.3902.3.102.6.1.1.3 | DisplayString | read-only | the description of alarm. |
| zxr10OutputAlarmTable | 1.3.6.1.4.1.3902.3.102.6.2 | not-accessible | the table of input alarm. | |
| zxr10OutputAlarmEntry | 1.3.6.1.4.1.3902.3.102.6.2.1 | not-accessible | the table of input alarm. | |
| INT zxr10OutputAlarmIndex | 1.3.6.1.4.1.3902.3.102.6.2.1.1 | INTEGER | read-only | the type of alarm. |
| INT zxr10OutputAlarmStatus | 1.3.6.1.4.1.3902.3.102.6.2.1.2 | INTEGER | read-write | the status of alarm. |
| STR zxr10OutputAlarmDescription | 1.3.6.1.4.1.3902.3.102.6.2.1.3 | DisplayString | read-only | the description of alarm. |
| zess | 1.3.6.1.4.1.3902.3.102.13 | |||
| INT zessClearAllChangeTimes | 1.3.6.1.4.1.3902.3.102.13.1 | INTEGER | read-write | Clear all zessChangeTimes of the domain table. |
| zessDomainTable | 1.3.6.1.4.1.3902.3.102.13.2 | not-accessible | A table that contains ZESS domain info. | |
| zessDomainEntry | 1.3.6.1.4.1.3902.3.102.13.2.1 | not-accessible | A list of entries of ZESS domain information. | |
| I32 zessDomainId | 1.3.6.1.4.1.3902.3.102.13.2.1.1 | Integer32 | read-only | The id of a ZESS domain. |
| I32 zessProtectInstanceId | 1.3.6.1.4.1.3902.3.102.13.2.1.2 | Integer32 | read-create | The protect instance id of a ZESS domain. |
| STR zessPrimaryPort | 1.3.6.1.4.1.3902.3.102.13.2.1.3 | DisplayString | read-create | The primary port name of the domain. |
| STR zessSecondaryPort | 1.3.6.1.4.1.3902.3.102.13.2.1.4 | DisplayString | read-create | The second port name of the domain. |
| I32 zessPreupDelayTime | 1.3.6.1.4.1.3902.3.102.13.2.1.5 | Integer32 | read-create | The preup deley time of the domain, it's default value is 2s. |
| INT zessDomainMode | 1.3.6.1.4.1.3902.3.102.13.2.1.6 | INTEGER | read-create | The mode of the domain. |
| INT zessDomainState | 1.3.6.1.4.1.3902.3.102.13.2.1.7 | INTEGER | read-only | The state of the domain. |
| INT zessPriIfState | 1.3.6.1.4.1.3902.3.102.13.2.1.8 | INTEGER | read-only | The state of the primary port. |
| INT zessSecIfState | 1.3.6.1.4.1.3902.3.102.13.2.1.9 | INTEGER | read-only | The state of the second port. |
| INT zessChangeTimes | 1.3.6.1.4.1.3902.3.102.13.2.1.10 | INTEGER | read-only | The change times of the domain. |
| INT zessClearChangeTimes | 1.3.6.1.4.1.3902.3.102.13.2.1.11 | INTEGER | read-create | Clear zessChangeTimes of the domain. |
| ROW zessDomainRowStatus | 1.3.6.1.4.1.3902.3.102.13.2.1.12 | RowStatus | read-create | The RowStatus of this row instance.It could be used for creating,modify or remove instance. createAndGo(4) is to create primary port and secondary port for a domain, destroy(6) is to delete a domain, notInService(2) is to delete primary port and secondary port in a domain. |
| vct | 1.3.6.1.4.1.3902.3.102.14 | |||
| vctPortTable | 1.3.6.1.4.1.3902.3.102.14.1 | not-accessible | The table of all ports' virtual cable test. | |
| vctPortEntry | 1.3.6.1.4.1.3902.3.102.14.1.1 | not-accessible | Each entry contains port config for VCT. | |
| STR vctPortName | 1.3.6.1.4.1.3902.3.102.14.1.1.1 | DisplayString | read-only | The port name to index vct config. |
| INT vctIsValid | 1.3.6.1.4.1.3902.3.102.14.1.1.2 | INTEGER | read-only | 0 means invalid,may be get message fail. 1 means valid |
| INT vctCableStatus | 1.3.6.1.4.1.3902.3.102.14.1.1.3 | INTEGER | read-only | This item indicates vct CableStatus. default fault |
| STR vctPair1Result | 1.3.6.1.4.1.3902.3.102.14.1.1.4 | DisplayString | read-only | This item indicates the cable status: open, short or impedance mismatch. |
| STR vctPair1Lenth | 1.3.6.1.4.1.3902.3.102.14.1.1.5 | DisplayString | read-only | This item indicates fault position. |
| STR vctPair2Result | 1.3.6.1.4.1.3902.3.102.14.1.1.6 | DisplayString | read-only | This item indicates the cable status: open, short or impedance mismatch. |
| STR vctPair2Lenth | 1.3.6.1.4.1.3902.3.102.14.1.1.7 | DisplayString | read-only | This item indicates fault position. |
| STR vctPair3Result | 1.3.6.1.4.1.3902.3.102.14.1.1.8 | DisplayString | read-only | This item indicates the cable status: open, short or impedance mismatch. |
| STR vctPair3Lenth | 1.3.6.1.4.1.3902.3.102.14.1.1.9 | DisplayString | read-only | This item indicates fault position. |
| STR vctPair4Result | 1.3.6.1.4.1.3902.3.102.14.1.1.10 | DisplayString | read-only | This item indicates the cable status: open, short or impedance mismatch. |
| STR vctPair4Lenth | 1.3.6.1.4.1.3902.3.102.14.1.1.11 | DisplayString | read-only | This item indicates fault position. |
| ROW vctRowStatus | 1.3.6.1.4.1.3902.3.102.14.1.1.12 | RowStatus | read-create | The RowStatus of this row instance.It could be used for creating instance.createAndGo(4) is to create a new row. |
| vctTable | 1.3.6.1.4.1.3902.3.102.14.2 | not-accessible | The vctTable contains the parameter of cable. | |
| vctEntry | 1.3.6.1.4.1.3902.3.102.14.2.1 | not-accessible | The parameter list of cable. | |
| I32 vctIfindex | 1.3.6.1.4.1.3902.3.102.14.2.1.1 | Integer32 | not-accessible | The ifindex of port,it is same to ifindex. |
| INT vctSetIfindex | 1.3.6.1.4.1.3902.3.102.14.2.1.2 | INTEGER | read-write | The ifindex of port, which need to be checked. |
| INT cableStatus | 1.3.6.1.4.1.3902.3.102.14.2.1.3 | INTEGER | read-only | The status of cable, either good or fault. |
| INT doubleCableStatus1_2 | 1.3.6.1.4.1.3902.3.102.14.2.1.4 | INTEGER | read-only | The status of cable pair 1-2. |
| INT doubleCableStatus3_6 | 1.3.6.1.4.1.3902.3.102.14.2.1.5 | INTEGER | read-only | The status of cable pair 3-6. |
| INT doubleCableStatus4_5 | 1.3.6.1.4.1.3902.3.102.14.2.1.6 | INTEGER | read-only | The status of cable pair 4-5. |
| INT doubleCableStatus7_8 | 1.3.6.1.4.1.3902.3.102.14.2.1.7 | INTEGER | read-only | The status of cable pair 7-8. |
| INT doubleCableLength1_2 | 1.3.6.1.4.1.3902.3.102.14.2.1.8 | INTEGER | read-only | The length of cable pair 1-2. |
| INT doubleCableLength3_6 | 1.3.6.1.4.1.3902.3.102.14.2.1.9 | INTEGER | read-only | The length of cable pair 3-6. |
| INT doubleCableLength4_5 | 1.3.6.1.4.1.3902.3.102.14.2.1.10 | INTEGER | read-only | The length of cable pair 4-5. |
| INT doubleCableLength7_8 | 1.3.6.1.4.1.3902.3.102.14.2.1.11 | INTEGER | read-only | The length of cable pair 7-8. |
| loopdetect | 1.3.6.1.4.1.3902.3.102.15 | |||
| I32 loopdetectReopenTime | 1.3.6.1.4.1.3902.3.102.15.1 | Integer32 | read-write | The delay(minute) reopenning the interface after it was shut down. default 10 minute |
| loopdetectTable | 1.3.6.1.4.1.3902.3.102.15.2 | not-accessible | The parameter which the loopdetectTable contains. | |
| loopdetectEntry | 1.3.6.1.4.1.3902.3.102.15.2.1 | not-accessible | The parameter list shows the happened loopdetect. | |
| I32 loopdetectPanelNum | 1.3.6.1.4.1.3902.3.102.15.2.1.1 | Integer32 | read-only | panel num . |
| I32 loopdetectPortNum | 1.3.6.1.4.1.3902.3.102.15.2.1.2 | Integer32 | read-only | port num . |
| STR loopdetectPortName | 1.3.6.1.4.1.3902.3.102.15.2.1.3 | DisplayString | read-only | The name of port, it is same to ifindex. |
| INT loopdetectPortOperStatus | 1.3.6.1.4.1.3902.3.102.15.2.1.4 | INTEGER | read-create | The status of the port. |
| STR loopdetectPortVlan | 1.3.6.1.4.1.3902.3.102.15.2.1.5 | DisplayString | read-create | The vlan list which the loopdetect port belong to. |
| INT loopdetectPortMonitor | 1.3.6.1.4.1.3902.3.102.15.2.1.6 | INTEGER | read-create | The loopdetect protocol enable/disable. |
| ROW loopdetectPortRowStatus | 1.3.6.1.4.1.3902.3.102.15.2.1.7 | RowStatus | read-create | The RowStatus of this row instance.It could be used for creating, modify instance.createAndGo(4) is to create a new row. |
| svlan | 1.3.6.1.4.1.3902.3.102.17 | |||
| I32 zxr10svlanCount | 1.3.6.1.4.1.3902.3.102.17.10 | Integer32 | read-only | The count of svlan session which has been used. |
| I32 zxr10svlanFreeCount | 1.3.6.1.4.1.3902.3.102.17.11 | Integer32 | read-only | The count of svlan session which has been not used. |
| zxr10svlanTable | 1.3.6.1.4.1.3902.3.102.17.12 | not-accessible | A table that contains SVLAN session config info. | |
| zxr10svlanEntry | 1.3.6.1.4.1.3902.3.102.17.12.1 | not-accessible | A list of entries of SVLAN session config information. | |
| I32 zxr10svlanSessionNo | 1.3.6.1.4.1.3902.3.102.17.12.1.1 | Integer32 | read-only | The session number of a session. |
| STR zxr10svlanDescription | 1.3.6.1.4.1.3902.3.102.17.12.1.2 | DisplayString | read-only | The description of a session. |
| STR zxr10svlanCustomerPort | 1.3.6.1.4.1.3902.3.102.17.12.1.3 | DisplayString | read-only | The customer port name of a session. |
| STR zxr10svlanUplinkPort | 1.3.6.1.4.1.3902.3.102.17.12.1.4 | DisplayString | read-only | The uplink port name of a session. |
| STR zxr10svlanInvlan | 1.3.6.1.4.1.3902.3.102.17.12.1.5 | DisplayString | read-only | svlan invlan ID,if invlan doesn't have value, this string will be null. |
| STR zxr10svlanOvlan | 1.3.6.1.4.1.3902.3.102.17.12.1.6 | DisplayString | read-only | The out vlan id of a session in no inner tag mode, if outvlan doesn't have value, this string will be null. |
| INT zxr10svlanRedirect | 1.3.6.1.4.1.3902.3.102.17.12.1.7 | INTEGER | read-only | The undirect flag of a session, default value 255 means redirect. |
| INT zxr10svlanAdvanced | 1.3.6.1.4.1.3902.3.102.17.12.1.8 | INTEGER | read-only | The advanced flag of a session, 0--normal,1--special,default value 255 means not config. |
| I32 zxr10svlanPriority | 1.3.6.1.4.1.3902.3.102.17.12.1.9 | Integer32 | read-only | Svlan priority can be mapping(8) or be a number of 0..7, default value 255 means that priority has no value. |
| STR zxr10svlanHelperVlan | 1.3.6.1.4.1.3902.3.102.17.12.1.10 | DisplayString | read-only | Svlan helper vlan ID, if helper vlan ID doesn't have value, this string will be null. |
| vfp | 1.3.6.1.4.1.3902.3.102.18 | |||
| zxr10vfpTable | 1.3.6.1.4.1.3902.3.102.18.1 | not-accessible | A table that contains VFP session config info. | |
| zxr10vfpEntry | 1.3.6.1.4.1.3902.3.102.18.1.1 | not-accessible | A list of entries of VFP session config information. | |
| STR zxr10vfpInterfaceName | 1.3.6.1.4.1.3902.3.102.18.1.1.1 | DisplayString | read-only | The interface name in a session. |
| I32 zxr10vfpSessionId | 1.3.6.1.4.1.3902.3.102.18.1.1.2 | Integer32 | read-only | The session id of a session. |
| STR zxr10vfpDescription | 1.3.6.1.4.1.3902.3.102.18.1.1.3 | DisplayString | read-only | The description of a session. |
| STR zxr10vfpInVlan | 1.3.6.1.4.1.3902.3.102.18.1.1.4 | DisplayString | read-only | Svlan invlan ID,if invlan doesn't have value, this string will be null. |
| I32 zxr10vfpAclNO | 1.3.6.1.4.1.3902.3.102.18.1.1.5 | Integer32 | read-only | Acl number of a session. |
| I32 zxr10vfpRuleNo | 1.3.6.1.4.1.3902.3.102.18.1.1.6 | Integer32 | read-only | Rule number of a session. |
| STR zxr10vfpOvlan | 1.3.6.1.4.1.3902.3.102.18.1.1.7 | DisplayString | read-only | The out vlan id of a session in no inner tag mode, if outvlan doesn't have value, this string will be null. |
| I32 zxr10vfpPriority | 1.3.6.1.4.1.3902.3.102.18.1.1.8 | Integer32 | read-only | Svlan priority can be mapping(8) or be a number of 0..7, default value 255 means that priority has no value. |
| INT zxr10vfpUntagAppFlag | 1.3.6.1.4.1.3902.3.102.18.1.1.9 | INTEGER | read-only | 0--global,1--pinpoint,2--notconfig,default value 255 means not config. |
| I32 zxr10vfpClassId | 1.3.6.1.4.1.3902.3.102.18.1.1.10 | Integer32 | read-only | Classid of a session,default value 255 means that classid has no value. |
| I32 zxr10vfpVrfId | 1.3.6.1.4.1.3902.3.102.18.1.1.11 | Integer32 | read-only | Vrfid of a session,default value 255 means that vrfid has no value. |
| dhcp | 1.3.6.1.4.1.3902.3.102.23 | |||
| I32 dhcpIpSourceGuardIfNumber | 1.3.6.1.4.1.3902.3.102.23.1 | Integer32 | read-only | It shows how many ports enable ip-source-guard configure |
| dhcpIpSourceGuardTable | 1.3.6.1.4.1.3902.3.102.23.2 | not-accessible | Control the ip-source-guard configure, | |
| dhcpIpSourceGuardEntry | 1.3.6.1.4.1.3902.3.102.23.2.1 | not-accessible | Control the ip-source-guard configure, | |
| INT dhcpIpSourceGuardSlot | 1.3.6.1.4.1.3902.3.102.23.2.1.1 | INTEGER | not-accessible | |
| INT dhcpIpSourceGuardPort | 1.3.6.1.4.1.3902.3.102.23.2.1.2 | INTEGER | not-accessible | |
| INT dhcpIpSourceGuardControl | 1.3.6.1.4.1.3902.3.102.23.2.1.3 | INTEGER | read-write | Control the ip-source-guard configure, if 0, disable current function; if 1, ip-source-guard is based on ip; if 2, ip-source-guard is based on mac; if 3, ip-source-guard is based on mac and ip. |
RFC description
Manages switching functions including VLANs, IGMP snooping, and QinQ encapsulation for ZTE ZXR10 devices.
Start monitoring ZTE ZXR10 switch series (VLAN/IGMP-snooping/QinQ config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.