ZHNSYSTEM

All MIBs › ZHNSYSTEM

Organization: Zhone Technologies MIB Working Group Other information about group editing the MIB

Last Updated: 2012-07-13

Category: Zhone Technologies CPE and Access

Description: Manages Zhone Technologies system configuration including device identity, software version, and reboot control.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ZHNSYSTEM?

This is a Zhone Technologies (a broadband access/DSL and fiber equipment vendor, later part of DASAN Zhone) private system MIB defining device-identity, configuration, and control objects for Zhone broadband access platforms. It exposes general system configuration data - model and MAC address information, WiFi network type, GPS-style location coordinates, system contact/location strings, system action (e.g., reboot) control, and timing/synchronization settings - spanning identity, physical location, and clocking categories. Its hardware/software status relevance includes device identity (modelNumber, macBaseAddress, numberOfMacAddresses) for inventory tracking, software-level control via zhnSystemAction for triggering reboots or resets, and timing/synchronization health via sysTransmitClockSource, sysLocalTimingReference, and sysSynchronizationMode, critical for access equipment relying on accurate network clocking. It appears to be a self-contained private enterprise MIB, though it likely follows SNMPv2-SMI conventions and may complement standard SNMPv2-MIB system group objects (sysContact/sysLocation naming suggests an intentional analog). It is typically deployed on Zhone broadband access devices (DSL/fiber access nodes, gateways) where operators need to track device identity, location, WiFi capability, and clock synchronization state as part of routine access-network management, and operators can download the ZHNSYSTEM MIB file to load it into their management platform.

IPNetwork Monitor allows you to monitor SNMP objects defined in ZHNSYSTEM. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Zhone Technologies broadband access node
Zhone DSL/fiber gateway

Monitoring Examples

An administrator would poll modelNumber and macBaseAddress/numberOfMacAddresses to confirm device inventory identity, and check sysSynchronizationMode alongside sysTransmitClockSource and sysLocalTimingReference to verify the access device's timing reference is correctly locked for services requiring synchronization. Setting zhnSystemAction to a reboot value provides remote software-level control, while locationLatitude/locationLongitude and zhnSysLocation/zhnSysContact support physical-location inventory tracking. If sysSynchronizationMode shows the unit has fallen back to a holdover or free-run state rather than its configured reference, that flags a clock synchronization fault on the access node.

What Can Be Monitored

model number and MAC address inventory
WiFi network type
device location coordinates
timing/synchronization mode and reference source
system reboot/action control

Imported Objects

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32
enterprises

From SNMPv2-TC

DisplayString
MacAddress
RowStatus
TEXTUAL-CONVENTION
TruthValue

From Zhone

zhoneWtn

OBJECT-IDENTITY

From Zhone-TC

ZhoneRowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
zhnSystem	1.3.6.1.4.1.5504.2.5.2			This file defines the private Enterprise MIB extensions that define system related objects. ============================================================== == == == Copyright (C) 2008-2012 Zhone Technologies, Inc. == == == ==============================================================
zhnSystemObjects	1.3.6.1.4.1.5504.2.5.2.1
zhnSystemGeneralObjects	1.3.6.1.4.1.5504.2.5.2.1.1
STR modelNumber	1.3.6.1.4.1.5504.2.5.2.1.1.1	DisplayString	read-only	model no. of the device
MAC macBaseAddress	1.3.6.1.4.1.5504.2.5.2.1.1.2	MacAddress	read-only	First MAC Address in series
U32 numberOfMacAddresses	1.3.6.1.4.1.5504.2.5.2.1.1.3	Unsigned32	read-only	Number of MAC Address sequentially defined in the Unit starting at the MAC Base Address.
WFN wifiNetworkType	1.3.6.1.4.1.5504.2.5.2.1.1.4	WFNT	read-write	Defines the Network Type or Mode of the Unit, i.e. Mesh or Base Station
UPT powerSupplyType	1.3.6.1.4.1.5504.2.5.2.1.1.5	UPT	read-only	Type of Power Supply that the unit is using
STR locationLatitude	1.3.6.1.4.1.5504.2.5.2.1.1.6	DisplayString	read-write	The latitude of the unit's location represented in degrees decimal. The format of the location's latitude is: [+ \| -]ddd.dddddddd where + indicates north - indicates south d is a decimal digit (0 <= d <= 9) Valid range is -90 to +90 degrees.
STR locationLongitude	1.3.6.1.4.1.5504.2.5.2.1.1.7	DisplayString	read-write	The longitude of the unit's location represented in degrees decimal. The format of the location's longitude is: [+ \| -]ddd.dddddddd where + indicates east - indicates west d is a decimal digit (0 <= d <= 9) Valid range is -180 to +180 degrees.
ROW zhnSystemAction	1.3.6.1.4.1.5504.2.5.2.1.1.8	RowStatus	read-write	Action parameter to handle the action on other scalars.
STR zhnSysLocation	1.3.6.1.4.1.5504.2.5.2.1.1.9	DisplayString	read-write	System location. This object is synonomous with the MIB II system sysLocation object.
STR zhnSysContact	1.3.6.1.4.1.5504.2.5.2.1.1.10	DisplayString	read-write	System contact. This object is synonomous with the MIB II system sysContact object.
TCS sysTransmitClockSource	1.3.6.1.4.1.5504.2.5.2.1.1.11	TCSI	read-write	T1 Clock source for PWE device. Since both T1/E1 interfaces will be required to have the same source, this object will replace the dsx1TransmitClockSource object in the DS1-MIB. This object is not supported by ZNID devices.
LTR sysLocalTimingReference	1.3.6.1.4.1.5504.2.5.2.1.1.12	LTRI	read-write	Source of the sysTransmitClockSource when set to Local. This object is not supported by ZNID devices.
CSM sysSynchronizationMode	1.3.6.1.4.1.5504.2.5.2.1.1.13	CSMI	read-write	Determines the method of ensuring Service Clock synchronization between the Source and Remote PWE devices.
SEI sysSynchronousEthernet	1.3.6.1.4.1.5504.2.5.2.1.1.14	SEI	read-write	Determines whether or not to use the 25MHz clock derived from the Synchronous Ethernet Port. This object is not supported by ZNID devices.
CMI sysClockMode	1.3.6.1.4.1.5504.2.5.2.1.1.15	CMI	read-write	Determines the mode for which the PWE chip will be initialized.
CDA sysCfgDBAction	1.3.6.1.4.1.5504.2.5.2.1.1.16	CDA	read-write	Perform an action on the configuration database.
RBT sysSoftwareReboot	1.3.6.1.4.1.5504.2.5.2.1.1.17	RBT	read-write	Perform a software reboot.
SCS sysSystemClockSource	1.3.6.1.4.1.5504.2.5.2.1.1.18	SCS	read-write	Determines the system-level clock mode for ZNID devices. uplink - the system will recover its clock from the configured uplink (e.g. GPON, SPF1, SFP2, etc.). ds1 - the system will recover its clock from the configured sysDs1ClockSourcePort. ieee1588 - the system will recover clock from the on-board 1588 clock circuitry.
ETC sysEthernetTransmitClockSource	1.3.6.1.4.1.5504.2.5.2.1.1.19	ETCS	read-write	Determines the transmit clock source for all ethernet ports requiring a clock. internal - all ethernet ports will recover clock from the local oscillator. systemClock - all ethernet ports will recover clock from the sysSystemClockSource.
STR sysDs1ClockSourcePort	1.3.6.1.4.1.5504.2.5.2.1.1.20	DisplayString	read-write	The interface name for the DS1 port providing transmit clock when the sysSystemClockSource is set to ds1.
OCT sysBootloaderVersion	1.3.6.1.4.1.5504.2.5.2.1.1.21	OCTET STRING	read-only	System bootloader (CFE) firmware version.
OCT sysFirmwareVersion	1.3.6.1.4.1.5504.2.5.2.1.1.22	OCTET STRING	read-only	The version of firmware the system is currently running.
OCT sysAltFirmwareVersion	1.3.6.1.4.1.5504.2.5.2.1.1.23	OCTET STRING	read-only	The alternate firmware version currently stored in system flash.
SYS sysRestoreAltFirmwareVersion	1.3.6.1.4.1.5504.2.5.2.1.1.24	SysFirmwareAction	read-write	This object can be used to restore the version of firmware to the alternate firmware version currently stored in flash.
T/F sysSnmpProvisioningLock	1.3.6.1.4.1.5504.2.5.2.1.1.25	TruthValue	read-write	This object can be set by an SNMP client to indicate that system configuration is in progress. All other SNMP clients will be locked out while this is set to true. This lock will timeout after 30 seconds.
U32 sysSnmpProvisioningChange	1.3.6.1.4.1.5504.2.5.2.1.1.26	Unsigned32	read-write	This object can be incremented by SNMP clients to indicate a sysCfgDBAction save has taken place.
zhnSystemBoardObjects	1.3.6.1.4.1.5504.2.5.2.1.2
U32 numberOfBoards	1.3.6.1.4.1.5504.2.5.2.1.2.1	Unsigned32	read-only	Number of boards in the Unit with Name, Part Number, Serial Number and Revision Number values
boardDescriptorTable	1.3.6.1.4.1.5504.2.5.2.1.2.2		not-accessible	Table of boards: Name, Part Number, Serial Number and Revision Number values
boardDescriptorEntry	1.3.6.1.4.1.5504.2.5.2.1.2.2.1		not-accessible	Table of boards: Name, Part Number, Serial Number and Revision Number values
U32 boardIndex	1.3.6.1.4.1.5504.2.5.2.1.2.2.1.1	Unsigned32	not-accessible	Board Index (Zero relative)
STR boardName	1.3.6.1.4.1.5504.2.5.2.1.2.2.1.2	DisplayString	read-only	Name of the Board as created by the system
STR boardPartNumber	1.3.6.1.4.1.5504.2.5.2.1.2.2.1.3	DisplayString	read-only	Part Number of the Board. Read from the board
STR boardSerialNumber	1.3.6.1.4.1.5504.2.5.2.1.2.2.1.4	DisplayString	read-only	Serial Number of the Board. Read from the board
STR boardRevision	1.3.6.1.4.1.5504.2.5.2.1.2.2.1.5	DisplayString	read-only	Revision Number of the Board. Read from the board
zhnSystemPldObjects	1.3.6.1.4.1.5504.2.5.2.1.3
U32 numberOfPlds	1.3.6.1.4.1.5504.2.5.2.1.3.1	Unsigned32	read-only	Number of PLDs in the Unit with Name and Version Number values
pldDescriptorTable	1.3.6.1.4.1.5504.2.5.2.1.3.2		not-accessible	Table of boards: Name, Part Number, Serial Number and Revision Number values
pldDescriptorEntry	1.3.6.1.4.1.5504.2.5.2.1.3.2.1		not-accessible	Table of boards: Name, Part Number, Serial Number and Revision Number values
U32 pldIndex	1.3.6.1.4.1.5504.2.5.2.1.3.2.1.1	Unsigned32	not-accessible	PLD Index (Zero relative)
STR pldName	1.3.6.1.4.1.5504.2.5.2.1.3.2.1.2	DisplayString	read-only	Name of the PLD as created by the system
STR pldVersion	1.3.6.1.4.1.5504.2.5.2.1.3.2.1.3	DisplayString	read-only	PLD Software Version. Read from the PLD
zhnSystemRadioObjects	1.3.6.1.4.1.5504.2.5.2.1.4
U32 numberOfRadios	1.3.6.1.4.1.5504.2.5.2.1.4.1	Unsigned32	read-only	Number of Radios in the Unit
zhnSystemEthernetLikeObjects	1.3.6.1.4.1.5504.2.5.2.1.5
U32 numberOfEthernetLikeInterfaces	1.3.6.1.4.1.5504.2.5.2.1.5.1	Unsigned32	read-write	Number of Ethernet Like Interfaces with Name, Type and Subtype
ethernetlikeInterfaceTable	1.3.6.1.4.1.5504.2.5.2.1.5.2		not-accessible	Table of ethernet-like Interfaces
ethernetlikeInterfaceEntry	1.3.6.1.4.1.5504.2.5.2.1.5.2.1		not-accessible	Table of ethernet-like interfaces having Name, type, subtype, number of ports, line power and number of pairs with power
U32 etherIndex	1.3.6.1.4.1.5504.2.5.2.1.5.2.1.1	Unsigned32	not-accessible	Index of the Ethernet Like Interface (zero relative)
STR etherName	1.3.6.1.4.1.5504.2.5.2.1.5.2.1.2	DisplayString	read-only	Name of the ethernet Like Interface as created by the system
ELT etherType	1.3.6.1.4.1.5504.2.5.2.1.5.2.1.3	ELTYPE	read-only	Type of Ethernet interface
ELS etherSubtype	1.3.6.1.4.1.5504.2.5.2.1.5.2.1.4	ELSUBTYPE	read-only	Subtype of Ethernet interface
U32 etherNumberOfPorts	1.3.6.1.4.1.5504.2.5.2.1.5.2.1.5	Unsigned32	read-only	Number of Ports on the Ethernet interface
LPT etherLinePower	1.3.6.1.4.1.5504.2.5.2.1.5.2.1.6	LPT	read-only	Line Power Type on this Ethernet Interface
I32 etherPowerPairs	1.3.6.1.4.1.5504.2.5.2.1.5.2.1.7	Integer32	read-only	Number of line Pairs providing power on the Ethernet interface
zhnSystemTempSensorObjects	1.3.6.1.4.1.5504.2.5.2.1.6
U32 numberOfTemperatureSensors	1.3.6.1.4.1.5504.2.5.2.1.6.1	Unsigned32	read-only	Number of Temperature Sensors in the Unit
temperatureSensorTable	1.3.6.1.4.1.5504.2.5.2.1.6.2		not-accessible	Table of Temperature Sensors: Name, Maximum, and Minimum values
temperatureSensorEntry	1.3.6.1.4.1.5504.2.5.2.1.6.2.1		not-accessible	Table of Temperature Sensors: Name, Maximum, and Minimum values
U32 temperatureSensorIndex	1.3.6.1.4.1.5504.2.5.2.1.6.2.1.1	Unsigned32	not-accessible	Temperature Sensor Index (Zero relative)
STR temperatureSensorName	1.3.6.1.4.1.5504.2.5.2.1.6.2.1.2	DisplayString	read-only	Name of the ethernet Like Interface as created by the system
STR temperatureSensorMaximum	1.3.6.1.4.1.5504.2.5.2.1.6.2.1.3	DisplayString	read-only	Maximum Temperature Recorded
STR temperatureSensorMinimum	1.3.6.1.4.1.5504.2.5.2.1.6.2.1.4	DisplayString	read-only	Minimum Temperature Recorded
zhnSystemSNMPObjects	1.3.6.1.4.1.5504.2.5.2.1.7
U32 numberOfCommunities	1.3.6.1.4.1.5504.2.5.2.1.7.1	Unsigned32	read-only	Number of SNMP Communities configured in the Unit
zhnCommunityTable	1.3.6.1.4.1.5504.2.5.2.1.7.2		not-accessible	This table is used to set the various configuration parameters for a particular community.
zhnCommunityTableEntry	1.3.6.1.4.1.5504.2.5.2.1.7.2.1		not-accessible	This object corresponds to an entry in the community table.
STR communityName	1.3.6.1.4.1.5504.2.5.2.1.7.2.1.1	DisplayString	not-accessible	This object corresponds to the SNMP community string.
INT communityType	1.3.6.1.4.1.5504.2.5.2.1.7.2.1.2	INTEGER	read-write	The access type of the community string. The default value of this object should be read-only(1).
ROW communityRowStatus	1.3.6.1.4.1.5504.2.5.2.1.7.2.1.3	RowStatus	read-create	When written, this object can be used to createAndGo(4) or destroy(6) a row from the table. A rowStatus value of notInService(2) will also destroy a row. RowStatus values of active(1), notReady(3), and createAndWait(5) are ignored.
zhnFixedCommunityTable	1.3.6.1.4.1.5504.2.5.2.1.7.3		not-accessible	This table is used to configure a read-only and a read-write community.
zhnFixedCommunityTableEntry	1.3.6.1.4.1.5504.2.5.2.1.7.3.1		not-accessible	This object corresponds to an entry in the fixed community table.
STR fixedCommunityName	1.3.6.1.4.1.5504.2.5.2.1.7.3.1.1	DisplayString	read-create	This object corresponds to the SNMP community string.
INT fixedCommunityType	1.3.6.1.4.1.5504.2.5.2.1.7.3.1.2	INTEGER	read-create	The access type of the community string. The default value of this object should be read-only(1).
ROW fixedCommunityRowStatus	1.3.6.1.4.1.5504.2.5.2.1.7.3.1.3	RowStatus	read-create	When written, this object is ignored. When read, a value of active(1) or notReady(3) will be returned.
zhnSystemTrapObjects	1.3.6.1.4.1.5504.2.5.2.1.8
U32 numberOfTrapManagers	1.3.6.1.4.1.5504.2.5.2.1.8.1	Unsigned32	read-only	Number of Trap Managers configured in the Unit
STR zhnDefaultTrapCommunity	1.3.6.1.4.1.5504.2.5.2.1.8.2	DisplayString	read-write	This object corresponds to the default trap community string. The default trap community string will be used when a community name is not configured for a particular trap manager.
INT zhnTrapTypeLinkUpDown	1.3.6.1.4.1.5504.2.5.2.1.8.3	INTEGER	read-write	Enable or disable all link up/down traps.
INT zhnTrapTypeAuthFailure	1.3.6.1.4.1.5504.2.5.2.1.8.4	INTEGER	read-write	Enable or disable the generation of authorization failure traps.
INT zhnTrapTypeConfigChange	1.3.6.1.4.1.5504.2.5.2.1.8.5	INTEGER	read-write	Enable or disable the generation of configuration change traps. This object is not supported by ZNID devices. Rather, the only mechanism to disable the generation of configuration change traps in a ZNID device is to disable the generation of all enterprise traps via the zhnTrapTypeEnterpise object.
zhnTrapManagerInfoTable	1.3.6.1.4.1.5504.2.5.2.1.8.6		not-accessible	This table is used to set the trap destination address for a particular community.
zhnTrapManagerInfoTableEntry	1.3.6.1.4.1.5504.2.5.2.1.8.6.1		not-accessible	This object corresponds to an entry in the community trap address info table.
IP trapDestination	1.3.6.1.4.1.5504.2.5.2.1.8.6.1.1	IpAddress	not-accessible	The IP Address of the destination to which a trap must be sent.
STR trapCommunityName	1.3.6.1.4.1.5504.2.5.2.1.8.6.1.2	DisplayString	read-write	This object corresponds to the trap community string. If not specified, the trapCommunityName will be set to the zhnDefaultTrapCommunity object.
INT trapVersion	1.3.6.1.4.1.5504.2.5.2.1.8.6.1.3	INTEGER	read-write	The trap types automatically supported by net-snmp and enabled/disabled in snmpd.conf. If not specified, the trapVersion will be set the default value of v2c.
INT trapPort	1.3.6.1.4.1.5504.2.5.2.1.8.6.1.4	INTEGER	read-write	The udp/tcp port number to which a trap must be sent. If not specified, the trapPort will be set the default value of 162.
ROW trapRowStatus	1.3.6.1.4.1.5504.2.5.2.1.8.6.1.5	RowStatus	read-create	When written, this object can be used to createAndGo(4) or destroy(6) a row from the table. A rowStatus value of notInService(2) will also destroy a row. RowStatus values of active(1), notReady(3), and createAndWait(5) are ignored.
INT zhnTrapTypeColdStart	1.3.6.1.4.1.5504.2.5.2.1.8.7	INTEGER	read-write	Enable or disable the generation of coldstart traps. A coldstart trap is generated each time the device is restarted.
INT zhnTrapTypeWarmStart	1.3.6.1.4.1.5504.2.5.2.1.8.8	INTEGER	read-write	Enable or disable the generation of warmstart traps. A warmstart trap is generated each time the device's SNMP agent is restarted.
INT zhnTrapTypeEnterprise	1.3.6.1.4.1.5504.2.5.2.1.8.9	INTEGER	read-write	Enable or disable the generation of all enterprise traps.
zhnSystemSyslogObjects	1.3.6.1.4.1.5504.2.5.2.1.9
SYS sysLogAdminStatus	1.3.6.1.4.1.5504.2.5.2.1.9.1	SysAdminStatus	read-write	Enable or disable the Syslog service.
SYS sysLogLocalLogLevel	1.3.6.1.4.1.5504.2.5.2.1.9.2	SysLogLevel	read-write	SysLog local log level options, per RFC 3164. All logged events with a severity at or greater than this level will be logged to the local log file. Note, the local log file is not persistent across system reboots.
SYS sysLogRemoteLogLevel	1.3.6.1.4.1.5504.2.5.2.1.9.3	SysLogLevel	read-write	SysLog remote log level options, per RFC 3164. All logged events with a severity at or greater that this level will be sent to a remote Syslog server if the remote server address is configured and a route exists to the remote server.
SYS sysLogDisplayLogLevel	1.3.6.1.4.1.5504.2.5.2.1.9.4	SysLogLevel	read-write	SysLog log level options, per RFC 3164 for the display of log messages via a web browser. All logged events with a severity level at or greater than this level will be displayed.
SYS sysLogMode	1.3.6.1.4.1.5504.2.5.2.1.9.5	SysLogMode	read-write	SysLog logging mode of operation: local(1), -- Log messages only to the local, non-persistent log file remote(2), -- Log messages only to a remote syslog server both(3), -- Log messages to both a local log file and a remote syslog server
IP sysLogRemoteServerAddress	1.3.6.1.4.1.5504.2.5.2.1.9.6	IpAddress	read-write	The IP address of the remote syslog server.
U32 sysLogRemoteServerPort	1.3.6.1.4.1.5504.2.5.2.1.9.7	Unsigned32	read-write	The UDP port to use to transfer syslog messages to the remote syslog server.
zhnSystemSNTPObjects	1.3.6.1.4.1.5504.2.5.2.1.10
SYS sntpAdminStatus	1.3.6.1.4.1.5504.2.5.2.1.10.1	SysAdminStatus	read-write	Enable or disable the SNTP client.
SYS sntpOperStatus	1.3.6.1.4.1.5504.2.5.2.1.10.2	SysAdminStatus	read-write	Current operational status of the SNTP client.
OCT sntpServer1	1.3.6.1.4.1.5504.2.5.2.1.10.3	OCTET STRING	read-write	The domain name or IP address of the first SNTP server with which to synchronize the system time.
OCT sntpServer2	1.3.6.1.4.1.5504.2.5.2.1.10.4	OCTET STRING	read-write	The domain name or IP address of the second SNTP server with which to synchronize the system time.
OCT sntpServer3	1.3.6.1.4.1.5504.2.5.2.1.10.5	OCTET STRING	read-write	The domain name or IP address of the third SNTP server with which to synchronize the system time.
OCT sntpServer4	1.3.6.1.4.1.5504.2.5.2.1.10.6	OCTET STRING	read-write	The domain name or IP address of the fourth SNTP server with which to synchronize the system time.
OCT sntpServer5	1.3.6.1.4.1.5504.2.5.2.1.10.7	OCTET STRING	read-write	The domain name or IP address of the fifth SNTP server with which to synchronize the system time.
SYS sntpLocalTimeZone	1.3.6.1.4.1.5504.2.5.2.1.10.8	SysSntpTimeZones	read-write	Indicates the local time zone.
STR sntpCurrentDateAndTime	1.3.6.1.4.1.5504.2.5.2.1.10.9	DisplayString	read-write	Indicates the current date and time.
zhnSystemUserLoginObjects	1.3.6.1.4.1.5504.2.5.2.1.11
OCT adminUserName	1.3.6.1.4.1.5504.2.5.2.1.11.1	OCTET STRING	read-only	The username required to login as the system administrator. This user has unrestricted access to change and view all configuration, status and test parameters.
OCT adminPassword	1.3.6.1.4.1.5504.2.5.2.1.11.2	OCTET STRING	read-write	The password required to login as the system administrator. This field cannot contain a SPACE and is returned as a string of asterisks.
OCT supportUserName	1.3.6.1.4.1.5504.2.5.2.1.11.3	OCTET STRING	read-only	The username required to login to support the system. This user has access to system parameters required to maintain the system and run diagnostic tests.
OCT supportPassword	1.3.6.1.4.1.5504.2.5.2.1.11.4	OCTET STRING	read-write	The password required to login to support the system. This field cannot contain a SPACE and is returned as a string of asterisks.
OCT userUserName	1.3.6.1.4.1.5504.2.5.2.1.11.5	OCTET STRING	read-only	The username required to login as a general user of the system. This user can view configuration settings and statistics, as well as, update the system's software.
OCT userPassword	1.3.6.1.4.1.5504.2.5.2.1.11.6	OCTET STRING	read-write	The password required to login as a general user of the system. field cannot contain a SPACE and is returned as a string of asterisks.
zhnSystemPowerSheddingObjects	1.3.6.1.4.1.5504.2.5.2.1.12
SYS powerSheddingAdminStatus	1.3.6.1.4.1.5504.2.5.2.1.12.1	SysAdminStatus	read-only	Configuration of parameters for the power-shedding feature. The power-shedding objects are only supported by systems that include on-board power-management circuitry. When the system detects that it is running on battery power, it has the option to shut down all support (excluding the voice over IP telephone service).The power-shedding administrative state will enable or disable the power-shedding feature.
U32 powerSheddingShutdownDelay	1.3.6.1.4.1.5504.2.5.2.1.12.2	Unsigned32	read-only	The shutdown delay is the time delay, in minutes, after AC power is lost, before shutting down non-voice services.
U32 powerSheddingRestoreDelay	1.3.6.1.4.1.5504.2.5.2.1.12.3	Unsigned32	read-only	The restore delay is the time delay, in minutes, after AC power is restored before switching on the services that were shut down due to the power loss.
zhnSystemFirewallObjects	1.3.6.1.4.1.5504.2.5.2.1.13
T/F sysFirewallEnable	1.3.6.1.4.1.5504.2.5.2.1.13.1	TruthValue	read-write	Enables or disables the firewall feature for the entire system.
T/F sysFirewallTcpSynCookies	1.3.6.1.4.1.5504.2.5.2.1.13.2	TruthValue	read-only	Enables or disables the TCP SYNCookie protection against SYN flooding denial-of-service attack.
zhnSystemDNSClientObjects	1.3.6.1.4.1.5504.2.5.2.1.14
NUM sysDNSAddressingType	1.3.6.1.4.1.5504.2.5.2.1.14.1	IPInterfaceAddressingTypeValues	read-write	Type of IP interface addressing method used to reach the DNS.
OCT sysDNSDHCPSource	1.3.6.1.4.1.5504.2.5.2.1.14.2	OCTET STRING	read-write	Name of the interface used by the DHCP Client to obtain DNS information.
IP sysDNSPrimaryIPAddress	1.3.6.1.4.1.5504.2.5.2.1.14.3	IpAddress	read-write	Primary Address of DNS when the addressing type is set to Static.
IP sysDNSSecondaryIPAddress	1.3.6.1.4.1.5504.2.5.2.1.14.4	IpAddress	read-write	Secondary Address of DNS when the addressing type is set to Static.
zhnSystemDNSProxyObjects	1.3.6.1.4.1.5504.2.5.2.1.15
U32 zhnDnsProxyHostMaxHostEntries	1.3.6.1.4.1.5504.2.5.2.1.15.1	Unsigned32	read-write	The maximum number of host entries in the DnsProxyHostObjectTable.
zhnDnsProxyHostTable	1.3.6.1.4.1.5504.2.5.2.1.15.2		not-accessible	This table is used to configure a DNS Proxy Host entry.
zhnDnsProxyHostEntry	1.3.6.1.4.1.5504.2.5.2.1.15.2.1		not-accessible	This object corresponds to an entry in the DNS Proxy Host table.
U32 dnsProxyHostIndex	1.3.6.1.4.1.5504.2.5.2.1.15.2.1.1	Unsigned32	not-accessible	Index into the DNS Proxy Host table
IP dnsProxyHostIPAddress	1.3.6.1.4.1.5504.2.5.2.1.15.2.1.2	IpAddress	read-write	The local proxy host IP address.
OCT dnsProxyHostName	1.3.6.1.4.1.5504.2.5.2.1.15.2.1.3	OCTET STRING	read-write	The domain name assigned to the host IP address.
ZHO dnsProxyRowStatus	1.3.6.1.4.1.5504.2.5.2.1.15.2.1.4	ZhoneRowStatus	read-create	Create or destroy a DNS Proxy Host. Upon creation, the dnsProxyHostIPAddress must be provided.
zhnSystemWanBackupObjects	1.3.6.1.4.1.5504.2.5.2.1.16
U32 failoverTimer	1.3.6.1.4.1.5504.2.5.2.1.16.1	Unsigned32	read-write	The WAN Failover Timer is used to determine how long (in seconds) the Fiber uplink interface must be operationally DOWN before a USB Cellular WAN Backup connection will be initiated. The Default value is 0 seconds, which DISABLES this feature. The recommended value to enable this feature is 60 seconds.
U32 restoralTimer	1.3.6.1.4.1.5504.2.5.2.1.16.2	Unsigned32	read-write	The WAN Restoral Timer is used to determine how long (in seconds) the Fiber uplink interface must remain in an operational UP condition before the Cellular Backup connection will be terminated and the traffic that was being forwarded out the USB interface is forwarded to the 5xx GEM instead. The default value is 60 seconds.
U32 backupDataVlan	1.3.6.1.4.1.5504.2.5.2.1.16.3	Unsigned32	read-write	This is the Internet Access VLAN (GEM 5xx), which is the only service that can be backed up using the USB Cellular modem.
OCT cellularPinNumber	1.3.6.1.4.1.5504.2.5.2.1.16.4	OCTET STRING	read-write	A 4 digit PIN code used to unlock the SIM card. For GPRS/UMTS networks, *99# is typically used. For CDMA/EVDO networks, #777 is typically used.
OCT cellularDataNumber	1.3.6.1.4.1.5504.2.5.2.1.16.5	OCTET STRING	read-write	This is the number that the USB modem will dial to establish a cellular a cellular data connection. For GPRS/UMTS networks, *99# is typically used. For CDMA/EVDO networks, #777 is typically used.
OCT atInitCommands	1.3.6.1.4.1.5504.2.5.2.1.16.6	OCTET STRING	read-write	AT initialization command strings, if needed.
OCT accessPointName	1.3.6.1.4.1.5504.2.5.2.1.16.7	OCTET STRING	read-write	The Access Point Name (APN) for connections to the GPRS/UMTS network. This should be provided by the ISP. In North America, 3G cellular carriers do not require an APN.
OCT chapPapUsername	1.3.6.1.4.1.5504.2.5.2.1.16.8	OCTET STRING	read-write	Required for CHAP or PAP authentication. This configuration item should be left blank if CHAP or PAP is not used.
OCT chapPapPassword	1.3.6.1.4.1.5504.2.5.2.1.16.9	OCTET STRING	read-write	Required for CHAP or PAP authentication. This configuration item should be left blank if CHAP or PAP is not used.
U32 connectionTimeout	1.3.6.1.4.1.5504.2.5.2.1.16.10	Unsigned32	read-write	Specifies the duration of inactivity in seconds before the cellular data call will automatically terminate. A new call will be initiated automatically when a packet must be sent upstream on the designated VLAN if the WAN uplink is still Operationally Down. A value of 0 will DISABLE the Connection Timeout feature.
ADR backupIpAddressMode	1.3.6.1.4.1.5504.2.5.2.1.16.11	BasicAddressingTypeValues	read-write	The WAN IP Address, Default Gateway IP Address, Subnet Mask and DNS Server IP Address must all be defined for the USB Cellular Backup connection. When IP Address Mode is set to DHCP, a DHCP Request will be sent upstream after the Cellular Data Connection has been established to acquire this information dynamically. When the WAN Backup IP Addess Mode is set to Static, this information ust be statically configured.
IP backupIpAddress	1.3.6.1.4.1.5504.2.5.2.1.16.12	IpAddress	read-write	The IP Address to be used on the WAN uplink interface of a Cellular Backhaul connection. This parameter is acquired dynamically in DHCP mode and only configurable if the BackupIpAddressMode is Static.
IP backupDefaultGateway	1.3.6.1.4.1.5504.2.5.2.1.16.13	IpAddress	read-write	The IP Address of the Default Gateway to be used on the WAN uplink interface of a Cellular Backhaul connection. This parameter is acquired dynamically in DHCP mode and only configurable if the BackupIpAddressMode is Static.
IP backupSubnetMask	1.3.6.1.4.1.5504.2.5.2.1.16.14	IpAddress	read-write	The Subnet Mask to be used on the WAN uplink interface of a Cellular Backhaul connection. This parameter is acquired dynamically in DHCP mode and only configurable if the BackupIpAddressMode is Static.
IP backupPrimaryDns	1.3.6.1.4.1.5504.2.5.2.1.16.15	IpAddress	read-write	The IP Address of the Primary DNS Server to be used on the WAN uplink interface of a Cellular Backhaul connection. This parameter is acquired dynamically in DHCP mode and only configurable if the BackupIpAddressMode is Static.
IP backupSecondaryDns	1.3.6.1.4.1.5504.2.5.2.1.16.16	IpAddress	read-write	The IP Address of the Secondary DNS Server to be used on the WAN uplink interface of a Cellular Backhaul connection. This parameter is acquired dynamically in DHCP mode and only configurable if the BackupIpAddressMode is Static.
zhnSystemTr69cObjects	1.3.6.1.4.1.5504.2.5.2.1.17
sysTr69cConfigObjects	1.3.6.1.4.1.5504.2.5.2.1.17.1
T/F sysTr69cConfigLoggingSOAP	1.3.6.1.4.1.5504.2.5.2.1.17.1.1	TruthValue	read-write	Enable or disable showing SOAP messages on serial console and local TR69 Client log file.
T/F sysTr69cConfigConnectionRequestAuthentication	1.3.6.1.4.1.5504.2.5.2.1.17.1.2	TruthValue	read-write	Enable or disable connection request authentication.
sysTr69cServerObjects	1.3.6.1.4.1.5504.2.5.2.1.17.2
OCT sysTr69cServerURL	1.3.6.1.4.1.5504.2.5.2.1.17.2.1	OCTET STRING	read-write	URL for the CPE to connect to the ACS using the CPE WAN Management Protocol. This parameter MUST be in the form of a valid HTTP or HTTPS URL. The host portion of this URL is used by the CPE for server-side certificate authentication when using SSL or TLS.
OCT sysTr69cServerLastConnectedURL	1.3.6.1.4.1.5504.2.5.2.1.17.2.2	OCTET STRING	read-only	This value records the last URL which connected successfully to the TR69 client.
OCT sysTr69cServerUsername	1.3.6.1.4.1.5504.2.5.2.1.17.2.3	OCTET STRING	read-write	Username used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. This username is used only for HTTP-based authentication of the CPE.
OCT sysTr69cServerPassword	1.3.6.1.4.1.5504.2.5.2.1.17.2.4	OCTET STRING	read-write	Password used to authenticate the CPE when making a connection to the ACS using the CPE WAN Management Protocol. This username is used only for HTTP-based authentication of the CPE. When read by an ACS, this parameter returns an empty string, regardless of the value.
T/F sysTr69cServerPeriodicInformEnable	1.3.6.1.4.1.5504.2.5.2.1.17.2.5	TruthValue	read-write	When set to TRUE, the CPE will periodically send CPE information to the TR69 Server using the Inform method calls.
U32 sysTr69cServerPeriodicInformInterval	1.3.6.1.4.1.5504.2.5.2.1.17.2.6	Unsigned32	read-write	The duration in seconds of the interval for which the CPE MUST attempt to connect with the ACS and call the Inform method if PeriodicInform-Enable is true.
OCT sysTr69cServerParameterKey	1.3.6.1.4.1.5504.2.5.2.1.17.2.7	OCTET STRING	read-only	ParameterKey provides the ACS a reliable and extensible means to track changes made by the ACS. The value of ParameterKey MUST be equal to the value of the ParameterKey argument from the most recent successful SetParameterValues, AddObject, or DeleteObject method call from the ACS. The CPE MUST set ParameterKey to the value specified in the corresponding method arguments if and only if the method completes successfully and no fault response is generated. If a method call does not complete successfully implying that the changes requested in the method did not take effect, the value of ParameterKey MUST NOT be modified. The CPE MUST only modify the value of ParameterKey as a result of SetParameterValues, AddObject, DeleteObject, or due to a factory reset. On factory reset, the value of ParameterKey MUST be set to empty.
OCT sysTr69cServerBoundIfName	1.3.6.1.4.1.5504.2.5.2.1.17.2.8	OCTET STRING	read-write	Name of the WAN interface that the TR69 client should use when establishing communications with the ACS.
OCT sysTr69cServerConnectionRequestURL	1.3.6.1.4.1.5504.2.5.2.1.17.2.9	OCTET STRING	read-only	HTTP URL for an ACS to make a Connection Request notification to the CPE. In the form: http://host:port/path. The host portion of the URL MAY be the IP address for the management interface of the CPE in lieu of a host name.
OCT sysTr69cServerConnectionRequestUsername	1.3.6.1.4.1.5504.2.5.2.1.17.2.10	OCTET STRING	read-write	Username used to authenticate an ACS making a Connection Request to the CPE.
OCT sysTr69cServerConnectionRequestPassword	1.3.6.1.4.1.5504.2.5.2.1.17.2.11	OCTET STRING	read-write	Password used to authenticate an ACS making a Connection Request to the CPE. When read by an ACS, this parameter returns an empty string, regardless of the actual value.
T/F sysTr69cServerUpgradesManaged	1.3.6.1.4.1.5504.2.5.2.1.17.2.12	TruthValue	read-write	Indicates whether or not the ACS will manage upgrades for the CPE. If true (1), the CPE SHOULD not use other means other than the ACS to seek out available upgrades. If false (0), the CPE MAY use other means for this purpose.
zhnSystemConformance	1.3.6.1.4.1.5504.2.5.2.2
zhnSystemGroups	1.3.6.1.4.1.5504.2.5.2.2.1
zhnSystemActiveGroup	1.3.6.1.4.1.5504.2.5.2.2.1.1			A collection of System Information objects that are required for the device to be functional
zhnSystemTablesItems	1.3.6.1.4.1.5504.2.5.2.2.1.2			The table items for the device that are filled in when the table is present
zhnSystemConfigItems	1.3.6.1.4.1.5504.2.5.2.2.1.3			The collection of configurable scalar system objects.
zhnSystemTrapItems	1.3.6.1.4.1.5504.2.5.2.2.1.4			The collection of SNMP trap objects.
zhnSystemCommunityItems	1.3.6.1.4.1.5504.2.5.2.2.1.5			The collection of SNMP community objects.
zhnSystemFixedCommunityItems	1.3.6.1.4.1.5504.2.5.2.2.1.6			The collection of pre-provisioned SNMP community objects.
zhnSystemClockingItems	1.3.6.1.4.1.5504.2.5.2.2.1.7			The collection of system-wide clocking parameters only supported by ZNID devices.
zhnSyslogConfigGroup	1.3.6.1.4.1.5504.2.5.2.2.1.8			The collection of system-wide logging parameters only supported by ZNID devices.
zhnSntpConfigGroup	1.3.6.1.4.1.5504.2.5.2.2.1.9			The collection of SNTP server parameters only supported by ZNID devices.
zhnUserLoginGroup	1.3.6.1.4.1.5504.2.5.2.2.1.10			The collection of User login parameters only supported by ZNID devices.
zhnPowerSheddingGroup	1.3.6.1.4.1.5504.2.5.2.2.1.11			The collection of configurable power-shedding parameters only supported by ZNID devices.
zhnSystemFirewallGroup	1.3.6.1.4.1.5504.2.5.2.2.1.12			The collection of system firewall parameters only supported by ZNID devices.
zhnSystemDNSClientGroup	1.3.6.1.4.1.5504.2.5.2.2.1.13			The collection of system DNS Client parameters only supported by ZNID devices.
zhnSystemDNSProxyHostGroup	1.3.6.1.4.1.5504.2.5.2.2.1.14			The collection of system DNS Proxy Host parameters only supported by ZNID devices.
zhnSystemWanBackupGroup	1.3.6.1.4.1.5504.2.5.2.2.1.15			The collection of system WAN Backup parameters only supported by ZNID devices.
zhnSystemTr69cGroup	1.3.6.1.4.1.5504.2.5.2.2.1.16			The collection of system TR69 Client parameters only supported by ZNID devices.
zhnSystemCompliances	1.3.6.1.4.1.5504.2.5.2.2.2
zhnSystemCompliance	1.3.6.1.4.1.5504.2.5.2.2.2.1			The Compliance statement for SNMP entities which manage the display of Zhone System Information

RFC description

System-related management objects for Zhone WTN devices. Includes system configuration, DNS client objects, backup, and firewall settings.

Start monitoring Zhone Technologies broadband access node, Zhone DSL/fiber gateway (device-identity/timing-sync-mode status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ZHNSYSTEM

What Is ZHNSYSTEM?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description