ZHONE-COM-IP-STATIC-ROUTE-MIB

All MIBs › ZHONE-COM-IP-STATIC-ROUTE-MIB

Organization: Zhone Technologies, Inc.

Last Updated: 2006-07-14

Category: Zhone Technologies CPE and Access

Description: Manages Zhone Technologies static IP route configuration, administrative distance, and gateway addresses.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is ZHONE-COM-IP-STATIC-ROUTE-MIB?

This proprietary MIB from Zhone Technologies manages static IP routing configuration on Zhone access platforms. It exposes objects for defining static routes, including destination network, gateway address, and administrative distance/preference settings. Its primary use is configuration management rather than hardware/software status monitoring, though it does let an administrator verify that the intended static routes are correctly provisioned and active on the device. It has no explicit dependency noted on other standard MIBs beyond general IP routing concepts. It is deployed on Zhone broadband access or routing platforms requiring manually configured static IP routes. Engineers can download the ZHONE-COM-IP-STATIC-ROUTE-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in ZHONE-COM-IP-STATIC-ROUTE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Zhone Technologies broadband access/routing platform

Monitoring Examples

An administrator would review the static route table to confirm the destination network, gateway address, and administrative distance for each configured route match the intended network design. A missing or incorrect gateway address entry would indicate a misconfigured static route causing traffic to be dropped or misrouted. No concrete sample object names were supplied for this MIB, so this is based on the module description.

What Can Be Monitored

static route destination/gateway
administrative distance
route configuration status

Imported Objects

From IF-MIB

InterfaceIndexOrZero

From SNMPv2-SMI

Integer32
IpAddress
MODULE-IDENTITY
OBJECT-IDENTITY
OBJECT-TYPE
Unsigned32

From Zhone

zhoneIp	OBJECT-IDENTITY
zhoneModules	OBJECT-IDENTITY

From ZHONE-COM-IP-RD-MIB

rdIndex

OBJECT-TYPE

From Zhone-TC

ZhoneRowStatus

OIDs

OID symbolic	OID numeric	Type	Access	Description
staticRoute	1.3.6.1.4.1.5504.4.1.13			The MIB module representing static routes in Zhone Technologies products. Static routes are user-defined routes that cause packets moving between a source and a destination to take a specified path. Static routes can be important if a router cannot build a route to a particular destination. They are also useful for specifying a gateway of last resort to which all unroutable packets will be sent.
staticRouteTable	1.3.6.1.4.1.5504.4.1.13.1		not-accessible	The Static Routes table contains static routes assigned to all interfaces. Each interface automatically gets one or more static routes upon interface initialization. More static routes are added as needed (e.g. default gateway). Rows are added by assigning staticRouteDest, staticRouteNetMask, staticRouteNextHop (or staticRouteIfNumber), and setting staticRouteRowStatus to 'createAndGo'. Rows are removed by setting staticRouteRowStatus to 'destroy'.
staticRouteEntry	1.3.6.1.4.1.5504.4.1.13.1.1		not-accessible	An entry in the Static Route table.
IP staticRouteDest	1.3.6.1.4.1.5504.4.1.13.1.1.1	IpAddress	not-accessible	The destination network or host IP address of the static route. A default gateway is one with a destination of 0.0.0.0 and netmask 0.0.0.0.
IP staticRouteNetMask	1.3.6.1.4.1.5504.4.1.13.1.1.2	IpAddress	not-accessible	The destination IP network mask of the static route. A default gateway is one with a destination of 0.0.0.0 and netmask 0.0.0.0.
IP staticRouteNextHop	1.3.6.1.4.1.5504.4.1.13.1.1.3	IpAddress	not-accessible	The IP address of the nexthop router of the static route. This may be 0.0.0.0 for static routes that use an interface number rather than a nexthop address, as in the case of a destination directly reachable via an interface requiring no intermediary system to act as a gateway.
NUM staticRouteIfNumber	1.3.6.1.4.1.5504.4.1.13.1.1.4	InterfaceIndexOrZero	not-accessible	The interface of the static route. This is for directly connected destinations (i.e. use this instead of staticRouteNextHop). Unnumbered point-to-point interfaces require this value to be valid. In general, this value must be valid if staticRouteNextHop is not valid. If staticRouteNextHop is valid, then this value must represent the interface named by the nexthop address. This index comes from ifIndex of RFC2233.
U32 staticRouteMetric	1.3.6.1.4.1.5504.4.1.13.1.1.5	Unsigned32	read-create	A dimensionless quantity chosen at the discretion of the provisioner for the purpose of comparing static routes. The meaning of this value when static routes are redistributed to other protocols is protocol-dependent, and the resulting value after redistribution is determined by the route-maps in use for that protocol. Lower numeric values for this number indicate more preferred routes.
INT staticRouteEnable	1.3.6.1.4.1.5504.4.1.13.1.1.6	INTEGER	read-create	An enumeration of the administrative state of the static route. The possible values are either 'disabled' or 'enabled', where the static route entry is not considered when making forwarding decisions for 'disabled', and is so for 'enabled'. The default is 'enabled'.
ZHO staticRouteRowStatus	1.3.6.1.4.1.5504.4.1.13.1.1.7	ZhoneRowStatus	read-create	The status of a static route entry.
INT staticRouteType	1.3.6.1.4.1.5504.4.1.13.1.1.8	INTEGER	not-accessible	Determines if this entry is a traditional destination route or a source address based route.
I32 staticRouteFallbackMetric	1.3.6.1.4.1.5504.4.1.13.1.1.9	Integer32	read-create	This object contains the fallback metric value for routes that are a part of a fallback route pair. Please refer to the Zhone Technologies User's Reference Manual for more information about fallback route pairs. The value of this object must be greater than both of the staticRouteMetrics of fallback route pair.
U32 staticRoutePingInterval	1.3.6.1.4.1.5504.4.1.13.1.1.10	Unsigned32	read-create	This object defines the interval, in milliseconds, of succesive pings of the nexthop of an active fallback route pair. The minimum value is 500 milliseconds, and must be specified in increments of 100 milliseconds.
I32 staticRoutePingFailMax	1.3.6.1.4.1.5504.4.1.13.1.1.11	Integer32	read-create	This object contain the maximum number of times that the ping of the nexthop of an active route in a fallback route pair must fail, in a row, before this route is demoted to fallback and the other route in the fallback pair becomes the active route.
comIpStaticRoute	1.3.6.1.4.1.5504.6.63			IP Static Route MIB IP Software Minneapolis, MN

RFC description

IP static routing configuration and management. Defines user-configured routes with fallback metrics and health monitoring.

Start monitoring Zhone Technologies broadband access/routing platform (static-route destination/gateway config status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download ZHONE-COM-IP-STATIC-ROUTE-MIB

What Is ZHONE-COM-IP-STATIC-ROUTE-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description