All MIBs › XF-RADIOLINK-RLT-MIB
Organization: Ericsson AB
Last Updated: 2020-11-05
Category: Ericsson Radio Link
Description:
Manages Ericsson XF radio link terminal inventory, software version, and operational state objects.
Imported Objects
From ENTITY-MIB
| entLogicalIndex | OBJECT-TYPE |
| entPhysicalIndex | OBJECT-TYPE |
From HC-PerfHist-TC-MIB
| HCPerfCurrentCount |
From IF-MIB
| ifIndex | OBJECT-TYPE |
From INET-ADDRESS-MIB
| InetAddressIPv6 |
From PerfHist-TC-MIB
| PerfCurrentCount | |
| PerfIntervalCount |
From SNMPv2-CONF
| MODULE-COMPLIANCE | |
| OBJECT-GROUP |
From SNMPv2-SMI
| Counter32 | |
| Counter64 | |
| Gauge32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| TimeTicks |
From SNMPv2-TC
| DisplayString | |
| TEXTUAL-CONVENTION | |
| TruthValue |
From XF-TOP-MIB
| xfRadioLink | OBJECT-IDENTITY |
What Is XF-RADIOLINK-RLT-MIB?
This MIB belongs to Ericsson's MINI-LINK TN microwave radio product family, managing Radio Link Terminal (RLT) and Carrier Termination (CT) objects for dual-carrier radio link applications. It exposes inventory data, software version information, and operational state for the radio link and carrier termination hardware components. Its monitoring value centers on hardware/software status: tracking installed software version and current operational state of the radio and carrier terminations helps operators confirm the microwave link hardware is running correctly and on the expected firmware. As a MINI-LINK TN specific module, it likely complements other Ericsson XF-RADIOLINK MIBs (such as the terminal-level PTP MIB) covering the same physical link. It is deployed on Ericsson MINI-LINK TN microwave radio equipment supporting dual-carrier configurations in cellular backhaul networks. Engineers can download the XF-RADIOLINK-RLT-MIB file directly to load it into their MIB browser.
IPNetwork Monitor allows you to monitor SNMP objects defined in XF-RADIOLINK-RLT-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
What Can Be Monitored
- radio link terminal software version
- carrier termination operational state
- dual-carrier inventory status
- operational state of RLT/CT components
Supported Devices
- Ericsson MINI-LINK microwave radio equipment
Monitoring Examples
An administrator would check the RLT/CT operational state and software version objects to confirm both carriers in a dual-carrier bundle are up and running matching firmware. A carrier termination reporting a down or degraded operational state, or a software version mismatch between carriers, would indicate a hardware fault or an incomplete upgrade. No concrete sample object names were supplied for this MIB, so this scenario is inferred from the module description.
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| xfRadioLinkRltMIB | 1.3.6.1.4.1.193.81.3.4.5 | This MIB defines objects for Radio Link Terminal (RLT) and Carrier Termination (CT) for new Radio Link application in MINI-LINK TN supporting dual carrier capability. | ||
| xfRadioLinkRltObjects | 1.3.6.1.4.1.193.81.3.4.5.1 | |||
| xfChannelGroupTable | 1.3.6.1.4.1.193.81.3.4.5.1.1 | not-accessible | This table lists all relationships, for ech Channel Group (CG), between the Bonding/RLP interface and the RL WAN interface and allows to configure CG as either Bonding or Radio Link protection (RLP). | |
| xfChannelGroupEntry | 1.3.6.1.4.1.193.81.3.4.5.1.1.1 | not-accessible | An entry in the xfChannelGroupTable. | |
| I32 cgIfIndex | 1.3.6.1.4.1.193.81.3.4.5.1.1.1.1 | Integer32 | read-only | It is the ifIndex of WAN interface. The interface identified by atIfIndex is the same interface as identified by the same value of ifIndex. |
| INT cgTypeIndex | 1.3.6.1.4.1.193.81.3.4.5.1.1.1.2 | INTEGER | read-only | Index representing the Channel Group interface type: - Bonding (2) - RLP: Radio Link Protection (3) |
| INT xfIfStatus | 1.3.6.1.4.1.193.81.3.4.5.1.1.1.3 | INTEGER | read-only | This object defines the Channel Group interface type: either Bonding or RLP (Radio Link Protection). Default: notReady |
| xfLIMappingTable | 1.3.6.1.4.1.193.81.3.4.5.1.2 | not-accessible | This table is used when navigating from a logical entity to interface, representing the relationship between: - RLT logical entity and either Bonding/RLP interface; - Carrier Termination (CT) logical entity and RAU IF interface. | |
| xfLIMappingEntry | 1.3.6.1.4.1.193.81.3.4.5.1.2.1 | not-accessible | An entry in the xfLIMappingTable. | |
| I32 liEntLogicalIndex | 1.3.6.1.4.1.193.81.3.4.5.1.2.1.1 | Integer32 | read-only | The value of this object uniquely identifies the logical entity: RLT (Radio Link Terminal) and CT (Carrier Termination). The logical entity identified by liEntLogicalIndex is the same interface as identified by the same value of entLogicalIndex. |
| I32 liIfIndex | 1.3.6.1.4.1.193.81.3.4.5.1.2.1.2 | Integer32 | read-only | It represents the ifIndex of Bonding/RLP interface and RAU IF. The interface identified by liIfIndex is the same interface as identified by the same value of ifIndex. |
| STR xfLIName | 1.3.6.1.4.1.193.81.3.4.5.1.2.1.3 | DisplayString | read-only | It represents the Name of the Radio Link Terminal (RLT) or Carrier Termination (CT). |
| STR xfLIIfDescr | 1.3.6.1.4.1.193.81.3.4.5.1.2.1.4 | DisplayString | read-only | A textual string containing information about the ifDescr of both Channel Group interface (either Bonding or RLP (Radio Link Protection)) and RAU IF interface. |
| xfCarrierTerminationTable | 1.3.6.1.4.1.193.81.3.4.5.1.3 | not-accessible | This table is used to configure the Carrier Termination (CT). | |
| xfCarrierTerminationEntry | 1.3.6.1.4.1.193.81.3.4.5.1.3.1 | not-accessible | An entry in the xfCarrierTerminationTable. | |
| STR xfCarrierTermDistinguishedName | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.1 | DisplayString | read-only | It represents the distinguished name of the Carrier Termination in the format Rack/Slot/CT. |
| STR xfCarrierTermLabel | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.2 | DisplayString | read-write | Label identifying the Carrier Termination. It can be freely set by operator to label the Carrier Termination. |
| INT xfCarrierTermOperStatus | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.3 | INTEGER | read-only | It represents the operative status of the Carrier Termination: - down(2) - up(3) - degraded(4) - testing(5) |
| I32 xfCarrierTermRadioFrameId | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.4 | Integer32 | read-write | It represents the selected Radio Frame ID. |
| INT xfCarrierTermPreamble | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.5 | INTEGER | read-write | It allows to set different preambles in the radio frame of each Carrier Termination in a XPIC or MIMO configuration: - preambleA(2) - preambleB(3) - preambleC(4) - preambleD(5) For non XPIC nor MIMO configurations, it can be left to notSpecified(1). |
| CAR xfCarrierTermSelectedMinACM | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.6 | CarrierTermACMIndex | read-write | It represents the selected minimum Tx ACM (Adaptive Code Modulation). |
| CAR xfCarrierTermActualACM | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.7 | CarrierTermACMIndex | read-only | It represents the actual (current) Tx ACM (Adaptive Code Modulation). |
| CAR xfCarrierTermSelectedMaxACM | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.8 | CarrierTermACMIndex | read-write | It represents the selected maximum Tx ACM (Adaptive Code Modulation). |
| TIK xfCarrierTermCapabilitiesLastChange | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.9 | TimeTicks | read-only | The value of sysUpTime at the time of the last creation or deletion of an entry in the xfCarrierTerminationCapabilityTable. If the number of entries has been unchanged since the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| INT xfCarrierTermReferenceSEC | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.10 | INTEGER | read-write | Reference Spectrum Efficiency Class (SEC): - notSpecified(1): not configured, not possible to set - sec2(2): spectrum eff. Class 2 - sec4L(3): spectrum eff. Class 4L - sec4H(4): specturm eff. Class 4H - sec5LB(5): spectrum eff. Class 5LB - sec5HB(6): spectrum eff. Class 5HB - sec6LB(7): spectrum eff. Class 6LB - sec6HB(8): spectrum eff. Class 6HB - sec7B(9): spectrum eff. Class 7B In ETSI, a value different from notSpecified(1) must be configured. In ANSI, no value can be set and notSpecified(1) is always returned. Near end access: read-write. Far end access: read-write. |
| I32 xfCarrierTermWantedLicensedCapacity | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.11 | Integer32 | read-write | It represents the wanted traffic licensed capacity on the Carrier Termination, expressed in Kbps. The default value 0 (i.e. disabled) means that no wanted licensed capacity has been selected by the user. The value used by RL license logic to request capacity licenses for the Carrier Termination is: - the capacity of selected max profile, if xfCarrierTermWantedLicensedCapacity = 0 - the value of xfCarrierTermWantedLicensedCapacity itself, if it is different from 0 |
| I32 xfCarrierTermActualLicensedCapacity | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.12 | Integer32 | read-only | This MO represents the Actual Licensed Capacity used on the Carrier Termination: - if Wanted Licensed Capacity is disabled (i.e. xfCarrierTermWantedLicensedCapacity = 0), the Selected Max ACM (xfCarrierTermSelectedMaxACM MO) is used for requesting the license capacity on the carrier; - if Wanted Licensed Capacity is enabled (i.e. xfCarrierTermWantedLicensedCapacity > 0), the value of Wanted Licensed Capacity itself is used for requesting the license capacity on the carrier. |
| I32 xfCarrierTermActualCapacity | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.13 | Integer32 | read-only | It represents the actual transmitted capacity supported by Carrier Termination in Kbps. |
| INT xfCarrierTermPolarization | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.14 | INTEGER | read-write | XPIC polarization, either horizontal or vertical. |
| INT xfCarrierTermXPICOperStatus | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.15 | INTEGER | read-only | XPIC locking status: - Other(1): don't use - Locked(2): XPIC is locked: XPI valid - Unlocked(3): XPIC is not locked: XPI not valid - Mute(4): XPIC is muted (XPIC recovery started) - NotApplicable(5): XPIC is disabled |
| INT xfCarrierTermMIMOOperStatus | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.16 | INTEGER | read-only | MIMO locking status: - Other(1): don't use - Locked(2): MIMO is locked: XPI and SNIR valid - Unlocked(3): MIMO is not locked: XPI and SNIR not valid - Mute(4): MIMO is muted - NotApplicable(5): MIMO is disabled |
| I32 xfCarrierTermSNIR | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.17 | Integer32 | read-only | Signal to Noise Interference Ratio (SNIR) in dB. |
| I32 xfCarrierTermXPI | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.18 | Integer32 | read-only | Cross-Polar Interference (XPI) level of the receiver in tenth of dB. |
| INT xfCarrierTermReset | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.19 | INTEGER | read-write | Reset command forces all the Carrier Termination settings to their own default. |
| INT xfCarrierTermRestore | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.20 | INTEGER | read-write | Restore command clears RFloop, IFloop and turns RAU transmitter on. |
| INT xfCarrierTermAutoRemoveLoopEnable | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.21 | INTEGER | read-write | Auto remove all RL loops after 15 minutes. |
| INT xfCarrierTermBerAlarmThreshold | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.22 | INTEGER | read-write | Threshold for BER alarm. Default: ber1e3(2). |
| CAR xfCarrierTermActualRxACM | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.23 | CarrierTermACMIndex | read-only | It represents the actual (current) Rx ACM (Adaptive Code Modulation). |
| BIT xfCarrierTermFeCTSeverity | 1.3.6.1.4.1.193.81.3.4.5.1.3.1.24 | Bits | read-only | This object represents the highest severity of Far-End CT alarms and is populated only if Far-End terminal is represented by a Packet terminal (PT). Craft uses this MO to colour the box representing the Far-End CT in the hop view. In case of the Far-End is a TN, the remote highest alarm severity of CT is referred to the interfaces: RAU IF and RF IF. |
| xfCarrierTerminationCapabilityTable | 1.3.6.1.4.1.193.81.3.4.5.1.4 | not-accessible | This table is used to configure the Carrier Termination (CT). | |
| xfCarrierTerminationCapabilityEntry | 1.3.6.1.4.1.193.81.3.4.5.1.4.1 | not-accessible | An entry in the xfCarrierTerminationCapabilityTable. | |
| I32 xfRadioFrameId | 1.3.6.1.4.1.193.81.3.4.5.1.4.1.1 | Integer32 | read-only | It represents the Radio Frame Id. |
| INT xfChannelSpacing | 1.3.6.1.4.1.193.81.3.4.5.1.4.1.2 | INTEGER | read-only | Channel spacing: - ETSI: 3.5, 7, 14, 28, 40, 56, 112 MHz - ANSI: 10, 20, 30, 40, 50, 60, 80 MHz |
| INT xfFrameFormatType | 1.3.6.1.4.1.193.81.3.4.5.1.4.1.3 | INTEGER | read-only | It represents the Frame Format type: - Standard - XPIC - MIMO - Long Haul Standard - Long Haul XPIC - XPIC on two boards - Long Haul XPIC on two boards |
| I32 xfMinACMCapacity | 1.3.6.1.4.1.193.81.3.4.5.1.4.1.4 | Integer32 | read-only | It represents the minimum capacity designed for the specific frame format (Radio Frame Id). |
| I32 xfMaxACMCapacity | 1.3.6.1.4.1.193.81.3.4.5.1.4.1.5 | Integer32 | read-only | It represents the maximum capacity designed for the frame format (Radio Frame Id). |
| BIT xfACMProfile | 1.3.6.1.4.1.193.81.3.4.5.1.4.1.6 | Bits | read-only | It specifies which adaptive code and modulation profiles are supported. |
| xfACMProfileCapacityTable | 1.3.6.1.4.1.193.81.3.4.5.1.5 | not-accessible | This tables reports the ACM capacities of the selected Radio Frame Id per each Carrier Termination. | |
| xfACMProfileCapacityEntry | 1.3.6.1.4.1.193.81.3.4.5.1.5.1 | not-accessible | An entry in the xfACMProfileCapacityTable. | |
| CAR xfACMIndex | 1.3.6.1.4.1.193.81.3.4.5.1.5.1.1 | CarrierTermACMIndex | read-only | It represents the positional index of the bitmap xfACMProfile in xfCarrierTerminationCapabilityTable. |
| I32 xfACMCapacity | 1.3.6.1.4.1.193.81.3.4.5.1.5.1.2 | Integer32 | read-only | It represents the capacity in Kbps of the ACM profile identified by the positional index xfACMIndex of the xfACMProfile in xfCarrierTerminationCapabilityTable. Value 0 means that the ACM profile is not included in current Frame Format. |
| xfRLTTable | 1.3.6.1.4.1.193.81.3.4.5.1.6 | not-accessible | This table is used to configure the Radio Link Terminal (RLT). | |
| xfRLTEntry | 1.3.6.1.4.1.193.81.3.4.5.1.6.1 | not-accessible | An entry in the xfRLTTable. | |
| I32 rltEntLogicalIndex | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.1 | Integer32 | read-only | It represents the entLogicalIndex of the Radio Link Terminal (RLT). The logical entity identified by rltEntLogicalIndex is the same entity as identified by the same value of entLogicalIndex. |
| STR xfRLTDistinguishedName | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.2 | DisplayString | read-only | It represents the distinguished name of the Radio Link Terminal (RLT): Rack/Slot/RLT number. It is the ifName of RL-WAN i/f. |
| IP xfRLTIpAddress | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.3 | IpAddress | read-only | IPv4 address of the network element the Radio Link Terminal (RLT) belongs to. |
| ADR xfRLTIPv6Address | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.4 | InetAddressIPv6 | read-only | IPv6 Address of the network element the Radio Link Terminal (RLT) belongs to. |
| STR xfRLTNeName | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.5 | DisplayString | read-only | The name of the network element the Radio Link Terminal (RLT) belongs to (System Name - sysName). |
| STR xfRLTNeType | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.6 | DisplayString | read-only | The type of the network element the Radio Link Terminal (RLT) belongs to (System Descr - sysDescr). |
| STR xfRLTId | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.7 | DisplayString | read-write | Radio Link Terminal (RLT) identifier used for integrity check with far-end. |
| STR xfRLTExpectedFarEndId | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.8 | DisplayString | read-write | Expected Id of far-end Radio Link Terminal (RLT), used for integrity check with near-end. |
| INT xfRLTFarEndIdCheck | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.9 | INTEGER | read-write | When enabled, the system verifies that far-end Radio Link Terminal name is equal to the expected. If ok Radio Link Terminal status is UP. If not ok the Radio Link Terminal status is stated as DOWN. Default value: disabled. |
| INT xfRLTStatus | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.10 | INTEGER | read-only | It represents the operational status of the Radio Link Terminal (RLT). |
| INT xfRLTMode | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.11 | INTEGER | read-write | The mode of the Radio Link Terminal (RLT). Values: - 1+0: onePlusZero (default) - 1+1 RLP: onePlusOneRadioLinkProtection - 2+0 RLB: twoPlusZeroAdvancedRadioLinkBonding - 1+1 RLP EQP: onePlusOneRadioLinkProtectionAndEquipmentProtection - 2+0 RLB EQP: twoPlusZeroRadioLinkBondingAndEquipmentProtection - 2+2 RLP EQP: twoPlusTwoRadioLinkProtectionAndEquipmentProtection - 4+0 RLB EQP: fourPlusZeroRadioLinkBondingAndEquipmentProtection |
| G32 xfRLTActualTXTotalCapacity | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.12 | Gauge32 | read-only | It represents the total transmitted capacity throughput (considering both Packet and TDM traffic), expressed in bps, of the Radio Link Terminal (RLT). |
| G32 xfRLTActualTXPacketCapacity | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.13 | Gauge32 | read-only | It represents the transmitted packet capacity throughput (only packet traffic), expressed in bps, of the Radio Link Terminal (RLT). |
| G32 xfRLTLimitedTotalCapacity | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.14 | Gauge32 | read-only | It represents the total transmitted capacity throughput (considering both Packet and TDM traffic), expressed in bps, of the Radio Link Terminal (RLT) limited by License. |
| BIT xfRLTRltSeverity | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.15 | Bits | read-only | This object represents the highest severity alarm related to RLT with logical index 'rltEntLogicalIndex'. Node GUI uses the Far-End entry value (of this MIB MO) to define the colour of the Far-End RLT box in the hop view. |
| BIT xfRLTCapability | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.16 | Bits | read-only | Each bit of this object represents an RLT capability: Bit 0 - XPIC capability Bit 1 - TDM capability Bit 2 - CsPlurality capability Bit 3 - CtAutoSelection capability Bit 4 - OnePlusZero capability Bit 5 - OnePlusOneRadioLinkProtection capability Bit 6 - TwoPlusZeroAdvancedRadioLinkBonding capability Bit 7 - OnePlusOneRadioLinkProtectionWithEQP capability Bit 8 - TwoPlusZeroRadioLinkBondingWithEQP capability Bit 9 - TwoPlusTwoRadioLinkProtectionWithEQP capability Bit 10 - FourPlusZeroRadioLinkBondingWithEQP capability Bit 11 - XPIC between boards capability Bit 12 - XPIC Members Auto Selection capability Bit 13 - Manual EQP Switch capability Bit 14 - Enhanced ACM Protection: Maximum Capacity capability Bit 15 - Enhanced ACM Protection: Maximum Protection capability Bit 16 - Radio Link Encryption capability Bit 17 - MIMO capability Bit 18 - TX swicthover and SSD capability |
| TIK xfRLTInventoryLastChange | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.17 | TimeTicks | read-only | The value of sysUpTime at the time of the last creation or deletion of an entry in the xfRLTHierarchyModuleTable. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object contains a zero value. |
| INT xfRLTCpriMode | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.18 | INTEGER | read-only | Set the mode of the CPRI front-haul product. Default: notApplicable. |
| INT xfRLTReset | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.19 | INTEGER | read-write | It resets RLT to default configuration. |
| INT xfRLTMeasuredHopLength | 1.3.6.1.4.1.193.81.3.4.5.1.6.1.20 | INTEGER | read-only | It represents the measured value of the radio hop length expressed in Km. Values: - Radio hop length measurement not yet available: -1; - Measured hop length in Km: > 0. |
| xfTrafficTable | 1.3.6.1.4.1.193.81.3.4.5.1.7 | not-accessible | This table is used to map the TDM interface to the specified RLT. | |
| xfTrafficEntry | 1.3.6.1.4.1.193.81.3.4.5.1.7.1 | not-accessible | An entry in the xfTrafficEntry. | |
| I32 trEntLogicalIndex | 1.3.6.1.4.1.193.81.3.4.5.1.7.1.1 | Integer32 | read-only | It represents the entLogicalIndex of the Radio Link Terminal (RLT). The logical entity identified by trEntLogicalIndex is the same interface as identified by the same value of entLogicalIndex. |
| INT xfTDMEnable | 1.3.6.1.4.1.193.81.3.4.5.1.7.1.2 | INTEGER | read-write | It allows to map TDM interface to a specific Radio Link Terminal (RLT). Default: disable. |
| xfRLTDMIfTable | 1.3.6.1.4.1.193.81.3.4.5.1.8 | not-accessible | This table is an extention of the ifTable used to configure TDM interface. | |
| xfRLTDMIfEntry | 1.3.6.1.4.1.193.81.3.4.5.1.8.1 | not-accessible | An entry in the xfRLTDMIfEntry. | |
| I32 xfRLTDMIfIndex | 1.3.6.1.4.1.193.81.3.4.5.1.8.1.1 | Integer32 | read-only | It is the ifIndex of RL TDM I/F table. |
| I32 xfActualTDMCapacity | 1.3.6.1.4.1.193.81.3.4.5.1.8.1.2 | Integer32 | read-only | It represents the current tributary capacity. |
| BIT xfWantedTDMAllocation | 1.3.6.1.4.1.193.81.3.4.5.1.8.1.3 | Bits | read-write | It represents the wanted tributary allocation. |
| BIT xfActualTDMAllocation | 1.3.6.1.4.1.193.81.3.4.5.1.8.1.4 | Bits | read-only | It represents the actual tributary allocation. |
| BIT xfTDMIfAlarms | 1.3.6.1.4.1.193.81.3.4.5.1.8.1.5 | Bits | read-only | This object shows TDM if related alarms. |
| INT xfTDMRxLoop | 1.3.6.1.4.1.193.81.3.4.5.1.8.1.6 | INTEGER | read-write | It configures TDM RX loop: - other(1) - enable(2) - disable(3) (default) |
| STR xfTDMDistinguishedName | 1.3.6.1.4.1.193.81.3.4.5.1.8.1.7 | DisplayString | read-only | It is the disinguished name of TDM i/f, i.e. R/S/P. |
| INT xfTDMMaxTributaries | 1.3.6.1.4.1.193.81.3.4.5.1.8.1.8 | INTEGER | read-only | It represents the maximum number of tributaries that can be allocated to TDM i/f, depending on frame ID, minimum ACM profile configured and licensed capacity in each CTs of the RLT. The maximum number is limited to 80. |
| INT xfTDMHopLength | 1.3.6.1.4.1.193.81.3.4.5.1.8.1.9 | INTEGER | read-write | It represents the length of the radio hop expressed in Km. This is used to calculate the propagation delay over the radio hop that shall be compensated to guarantee TDM traffic error free. Values: - default value for delay compensation: -1 - admissible range of values in Km: 0-200 |
| xfCGIfTable | 1.3.6.1.4.1.193.81.3.4.5.1.9 | not-accessible | This table is an extension of ifTable reporting the main characteristics of CG i/f. | |
| xfCGIfEntry | 1.3.6.1.4.1.193.81.3.4.5.1.9.1 | not-accessible | An entry in the xfCGIfEntry. | |
| I32 xfCGIfIndex | 1.3.6.1.4.1.193.81.3.4.5.1.9.1.1 | Integer32 | read-only | It is the ifIndex of CG interface. |
| I32 xfCGIfMinSpeed | 1.3.6.1.4.1.193.81.3.4.5.1.9.1.2 | Integer32 | read-only | The minimum speed (throughput) of this interface expressed in bit/s, including both Ethernet and TDM capacities. Note: in case of bonding configurations, it represents the minimum of the min speeds of all Carrier Terminations in the bonding group. |
| G32 xfCGIfMaxSpeed | 1.3.6.1.4.1.193.81.3.4.5.1.9.1.3 | Gauge32 | read-only | The maximum speed (throughput) of this interface expressed in bit/s, including both Ethernet and TDM capacities. Note: in case of bonding configurations, it represents the sum of the max speeds of all Carrier Terminations in the bonding group. |
| INT xfCGIfRCNum | 1.3.6.1.4.1.193.81.3.4.5.1.9.1.4 | INTEGER | read-only | Number of Carrier Termination members belonging to the CG group. |
| BIT xfCGIfAlarms | 1.3.6.1.4.1.193.81.3.4.5.1.9.1.5 | Bits | read-only | This object shows CG i/f related alarms. |
| INT xfCGIfHopViewStatus | 1.3.6.1.4.1.193.81.3.4.5.1.9.1.6 | INTEGER | read-only | This object represents the Hop View status. Up: Far-End is reachable Down: Far-End not reachable The status is related to HCC-NE alarm. |
| xfXPICPairTable | 1.3.6.1.4.1.193.81.3.4.5.1.10 | not-accessible | This table is used to enable XPIC (Admid Status) and set the CT pair in XPIC. | |
| xfXPICPairEntry | 1.3.6.1.4.1.193.81.3.4.5.1.10.1 | not-accessible | An entry in the xfXPICPairTable. | |
| I32 xpicPairEntLogicalIIndex | 1.3.6.1.4.1.193.81.3.4.5.1.10.1.1 | Integer32 | read-only | It represents the entLogicalIndex of the Radio Link Terminal (RLT). The logical entity identified by xpicPairEntLogicalIIndex is the same entity as identified by the same value of entLogicalIndex. |
| INT xfXPICPairAdminStatus | 1.3.6.1.4.1.193.81.3.4.5.1.10.1.2 | INTEGER | read-write | Administrative status of XPIC pair. Default value: disable. |
| INT xfXPICPairNumber | 1.3.6.1.4.1.193.81.3.4.5.1.10.1.3 | INTEGER | read-write | It specifies the number used for identification of the XPIC pair. |
| INT xfXPICPairRecovery | 1.3.6.1.4.1.193.81.3.4.5.1.10.1.4 | INTEGER | read-write | It allows to enable/disable the recovery procedure when XPIC mode is enabled. |
| INT xfXPICPairRestore | 1.3.6.1.4.1.193.81.3.4.5.1.10.1.5 | INTEGER | read-write | Restore XPIC functionality after XPIC recovery has been triggered and resets XPIC Auto Restore procedure |
| STR xfXPICCTmember1 | 1.3.6.1.4.1.193.81.3.4.5.1.10.1.6 | DisplayString | read-write | It specifies the first Carrier Termination (CT) member of the XPIC pair. The member is identified by the CT distinguished name (R/S/P). |
| STR xfXPICCTmember2 | 1.3.6.1.4.1.193.81.3.4.5.1.10.1.7 | DisplayString | read-write | It specifies the second Carrier Termination (CT) member of the XPIC pair. The member is identified by the CT distinguished name (R/S/P). |
| INT xfXPICAutoRestore | 1.3.6.1.4.1.193.81.3.4.5.1.10.1.8 | INTEGER | read-write | It enable/disables the XPIC Auto Recovery procedure. |
| INT xfXpicPairIndex | 1.3.6.1.4.1.193.81.3.4.5.1.10.1.9 | INTEGER | read-only | It represents the table second index and is used to index the XPIC pair associated to Radio Link Terminal (RLT) with entLogicalIndex equal to xpicPairEntLogicalIIndex. It has been introduce to support configurations like 4+0 RLB EQP, 2+2 RLP EQP. |
| xfMIMOGroupTable | 1.3.6.1.4.1.193.81.3.4.5.1.11 | not-accessible | This table is used to enable MIMO (Admid Status) and set the CTs in MIMO group. | |
| xfMIMOGroupEntry | 1.3.6.1.4.1.193.81.3.4.5.1.11.1 | not-accessible | An entry in the xfMIMOGroupTable. | |
| I32 mimoGroupEntLogicalIIndex | 1.3.6.1.4.1.193.81.3.4.5.1.11.1.1 | Integer32 | read-only | It represents the entLogicalIndex of the Radio Link Terminal (RLT). The logical entity identified by mimoGroupEntLogicalIIndex is the same entity as identified by the same value of entLogicalIndex. |
| INT xfMIMOGroupAdminStatus | 1.3.6.1.4.1.193.81.3.4.5.1.11.1.2 | INTEGER | read-write | Administrative status of MIMO group. Default value: disable. |
| INT xfMIMOGroupNumber | 1.3.6.1.4.1.193.81.3.4.5.1.11.1.3 | INTEGER | read-write | It specifies the Number used for identification of the MIMO group. |
| INT xfMIMOGroupRecovery | 1.3.6.1.4.1.193.81.3.4.5.1.11.1.4 | INTEGER | read-write | It allows to enable/disable the recovery procedure when MIMO mode is enabled. |
| INT xfMIMOGroupRestore | 1.3.6.1.4.1.193.81.3.4.5.1.11.1.5 | INTEGER | read-write | Restore MIMO functionality after MIMO recovery has been triggered. |
| STR xfMIMOCTmember1 | 1.3.6.1.4.1.193.81.3.4.5.1.11.1.6 | DisplayString | read-only | It specifies the first Carrier Termination (CT) member of the MIMO group. The member is identified by the CT distinguished name (R/S/P). |
| STR xfMIMOCTmember2 | 1.3.6.1.4.1.193.81.3.4.5.1.11.1.7 | DisplayString | read-only | It specifies the second Carrier Termination (CT) member of the MIMO group. The member is identified by the CT distinguished name (R/S/P). |
| STR xfMIMOCTmember3 | 1.3.6.1.4.1.193.81.3.4.5.1.11.1.8 | DisplayString | read-only | It specifies the third Carrier Termination (CT) member of the MIMO group. The member is identified by the CT distinguished name (R/S/P). |
| STR xfMIMOCTmember4 | 1.3.6.1.4.1.193.81.3.4.5.1.11.1.9 | DisplayString | read-only | It specifies the forth Carrier Termination (CT) member of the MIMO group. The member is identified by the CT distinguished name (R/S/P). |
| xfRLWANIfTable | 1.3.6.1.4.1.193.81.3.4.5.1.12 | not-accessible | This table is used to handle the RL-WAN i/f. | |
| xfRLWANIfEntry | 1.3.6.1.4.1.193.81.3.4.5.1.12.1 | not-accessible | An entry in the xfRLWANIfTable. | |
| I32 xfRLWANIfIndex | 1.3.6.1.4.1.193.81.3.4.5.1.12.1.1 | Integer32 | read-only | It is the table index. It contains the ifIndex value of the WAN interface. |
| STR xfRLWANDistinguishedName | 1.3.6.1.4.1.193.81.3.4.5.1.12.1.2 | DisplayString | read-only | It is the name uniquely identifying the RL-WAN interface within the system, i.e. R/S/P. |
| INT xfRLWANCompAdminStatus | 1.3.6.1.4.1.193.81.3.4.5.1.12.1.3 | INTEGER | read-write | It enables and disables MLHC and PLC on the RL-WAN interface. down(2): both MLHC and PLC are disabled. mlhcUp(3): only MLHC is enabled. mlhcPlcUp(4): both MLHC and PLC are enabled. Default:down(2). Compression can be enabled on only one of the two RL-WAN interfaces belonging to the same MMU. Any attempt to enable compression on both RL-WAN interfaces belonging to the same MMU is refused. |
| INT xfRLWANCompConnStatus | 1.3.6.1.4.1.193.81.3.4.5.1.12.1.4 | INTEGER | read-only | It specifies if the compression building block is physically connected to the RL-WAN interface. Physical connection of the compression building block to the RL-WAN interface is pre-requisite for enabling compression. When xfRLWANCompAdminStatus is set either to mlhcUp or mlhcPlcUp, the compression building block is physically connected to RL-WAN interfaces and xfRLWANCompConnStatus becomes connected. When xfRLWANCompAdminStatus is set either to mlhcUp or mlhcPlcUp on the other RL-WAN interface, the compression building block is physically connected to the other RL-WAN interfaces and xfRLWANCompConnStatus becomes disconnected. |
| INT xfRLWANMlhcMplsMode | 1.3.6.1.4.1.193.81.3.4.5.1.12.1.5 | INTEGER | read-write | It specifies the wanted mpls mode. mplsOnly(2): Ethernet customer bridge, provider bridge and QinQ headers, including MPLS labels (up to 3) are compressed. controlWord(3): L2 VPN with Pseudo-Wire Control Word headers are compressed. l2(4): L2 VPN without Pseudo-Wire Control Word headers are compressed. l3(5): L3 VPN headers are compressed. Default: mplsOnly(2). This can be configured only if compression administrative status is down. |
| INT xfRLWANMlhcOperStatus | 1.3.6.1.4.1.193.81.3.4.5.1.12.1.6 | INTEGER | read-only | Multi-Layer Header Compression operative status. |
| INT xfRLWANPlcOperStatus | 1.3.6.1.4.1.193.81.3.4.5.1.12.1.7 | INTEGER | read-only | Payload Compression operative status. |
| G32 xfRLWANActualCapacity | 1.3.6.1.4.1.193.81.3.4.5.1.12.1.8 | Gauge32 | read-only | Actual Capacity (speed) of RL WAN interface, in bps. |
| G32 xfRLWANLimitedCapacity | 1.3.6.1.4.1.193.81.3.4.5.1.12.1.9 | Gauge32 | read-only | Capacity (speed) limited by license of RL WAN interface, in bps. |
| xfRLTHierarchyModuleTable | 1.3.6.1.4.1.193.81.3.4.5.1.13 | not-accessible | This table is used to handle Module (MMU - RAU) hierarchy for the specific RLT. | |
| xfRLTHierarchyModuleEntry | 1.3.6.1.4.1.193.81.3.4.5.1.13.1 | not-accessible | An entry in the xfRLTHierarchyModuleTable. | |
| I32 xfRLTMHIndex | 1.3.6.1.4.1.193.81.3.4.5.1.13.1.1 | Integer32 | read-only | It is the table index. It contains the entPhisycalIndex of the WAN port associated to the RLT. |
| I32 xfRLTModuleIndex | 1.3.6.1.4.1.193.81.3.4.5.1.13.1.2 | Integer32 | read-only | It is the table index. It is a sequential number referred to the module (entity), either MMU or RAU, constituting the RLT. |
| I32 xfRLTEntPhysicalIndex | 1.3.6.1.4.1.193.81.3.4.5.1.13.1.3 | Integer32 | read-only | This MO represents the value of entPhysicalIndex of the module, either MMU or RAU, constituting the RLT. |
| I32 xfRLTPhysicalCointainedIn | 1.3.6.1.4.1.193.81.3.4.5.1.13.1.4 | Integer32 | read-only | This MO represents the value of entPhysicalIndex for the physical entity which 'contains' this physical entity, which is either MMU or RAU (constituting the RLT). |
| I32 xfRLTPhysicalParentRelPos | 1.3.6.1.4.1.193.81.3.4.5.1.13.1.5 | Integer32 | read-only | This MO represents the indication of the relative position of this 'child' component among all its 'sibling' components. |
| STR xfRLTEntityPhysicalDescr | 1.3.6.1.4.1.193.81.3.4.5.1.13.1.6 | DisplayString | read-only | This MO represents a textual description of physical entity (module), either MMU or RAU, constituting the RLT. |
| I32 xfRLTModuleSlotPosition | 1.3.6.1.4.1.193.81.3.4.5.1.13.1.7 | Integer32 | read-only | This MO represents the slot position of the physical entity (module), either MMU or RAU, constituting the RLT. |
| STR xfRLTFEDistinguishedName | 1.3.6.1.4.1.193.81.3.4.5.1.13.1.8 | DisplayString | read-only | This MO represents the distinguished name of the Near-End logical entity, either RLT or CT. |
| STR xfRLTNEDistinguishedName | 1.3.6.1.4.1.193.81.3.4.5.1.13.1.9 | DisplayString | read-only | This MO represents the distinguished name of the Far-End logical entity, either RLT or CT. |
| I32 xfRLTInterfaceIndex | 1.3.6.1.4.1.193.81.3.4.5.1.13.1.10 | Integer32 | read-only | This MO represents the value of ifIndex of the interface, either CG IF (Bonding/RLP) or RAU IF, constituting the RLT. |
| INT xfRLTHighestSeverityAlarm | 1.3.6.1.4.1.193.81.3.4.5.1.13.1.11 | INTEGER | read-only | This MO reports the highest severity of the alarms active in the physical module, MMU or RAU, it refers to. Value list: - critical(0): highest severity is Critical; - major(1): highest severity is Major; - minor(2): highest severity is Minor; - warning(3): highest severity is Warning; - clear(4): no alarm. |
| xfRLTProtectionTable | 1.3.6.1.4.1.193.81.3.4.5.1.14 | not-accessible | This table is used to handle RL Protection for the RLT whose mode is set 1+1RLP. | |
| xfRLTProtectionEntry | 1.3.6.1.4.1.193.81.3.4.5.1.14.1 | not-accessible | An entry in the xfRLTProtectionTable. | |
| I32 xfRLTProtIndex | 1.3.6.1.4.1.193.81.3.4.5.1.14.1.1 | Integer32 | read-only | It is the table index. It contains the entity logical index of the RLT configured in 1+1RLP. |
| INT xfRLTProtectionSwitchMode | 1.3.6.1.4.1.193.81.3.4.5.1.14.1.2 | INTEGER | read-write | The mode in which the switching mechanism is configured. Auto: System automatically switches from the degraded to the other transmitter (Tx). Manual: Automatic switching is disabled and operator can select Tx manually. Auto & Revertive: makes it possible to manually set the preferred Tx. TX switch disable: Selective Space Diverity, SSD. RLP TX switch is disabled. The two received signals, from different paths, are combined. Default: AUTO (for RLT mode RLP) & NA (default for RLT mode RLB). |
| INT xfRLTProtectionStatus | 1.3.6.1.4.1.193.81.3.4.5.1.14.1.3 | INTEGER | read-only | Status of the protection, when configured in a protected mode. Values: - unprotected; - protected - unableToProtect Note: Applicable only when RLT-mode is RL protection. |
| STR xfRLTRevertivePreferredTX | 1.3.6.1.4.1.193.81.3.4.5.1.14.1.4 | DisplayString | read-write | It specifies the preferred TX Radio Carrier Termination (CT) in revertive protection mode. The member is identified by the CT distinguished name (R/S/P). |
| INT xfRLTProtectionWaitToRestoreTime | 1.3.6.1.4.1.193.81.3.4.5.1.14.1.5 | INTEGER | read-write | The time, in # of seconds, to wait before switching back to the preferred Tx in Auto & Revertive mode. Default: 0. |
| INT xfRLTFadeNotificationTimer | 1.3.6.1.4.1.193.81.3.4.5.1.14.1.6 | INTEGER | read-write | Notifications for alarms caused by fading, with a duration less than the specified time (0 - 1000 seconds) are not sent. Only applicable for protected configurations. Default: 200. |
| INT xfRLTManualSwitchCommand | 1.3.6.1.4.1.193.81.3.4.5.1.14.1.7 | INTEGER | read-write | Used to request a TX switch-over. Applicable for protected configurations and when protectionSwitchMode is set to Manual. Not Applicable for RLT mode RLB Value: - txManualSwitch - txManualNoSwitch. |
| INT xfRLTTxSwitchOverConfiguration | 1.3.6.1.4.1.193.81.3.4.5.1.14.1.8 | INTEGER | read-write | Enable or disable the function to switch TX on a request from far-end, including also the TX switchover alarm notifications , both local and remote. Only applicable in RLT mode RLP. Values: - notSupported: (default for RLT in RLB mode) - enable: TX switchover triggered by local and remote faults - disable: TX switchover disabled(default for RLT in RLP mode) - DEPRECATED - enableLocal: TX switchover triggered by local faults only (default for RLT in RLP mode) |
| INT xfRLTTxSwitchOverAlarmReset | 1.3.6.1.4.1.193.81.3.4.5.1.14.1.9 | INTEGER | read-write | Used to manual reset the TX switch-over alarm and Remote TX switchover alarm (consequently to TX switch ordered from far-end). Note: the alarm is raised when TX Switch far-end function is enabled (xfRLTTxSwitchOverConfiguration). Value: - txSwitchOverAlarmNoReset - txSwitchOverAlarmReset. |
| I32 xfRLTNumOfRLPSwitch | 1.3.6.1.4.1.193.81.3.4.5.1.14.1.10 | Integer32 | read-only | It represents the number of RLP Radio TX switch. |
| INT xfRLTEnhancedACMProtectionMode | 1.3.6.1.4.1.193.81.3.4.5.1.14.1.11 | INTEGER | read-write | It configures the enhanced ACM protection mode. The enhanced ACM protection uses RX indicators from both the working and the protection links to select an ACM profile to optimize capacity (throughput) and/or protection (robustness). Values: - Active Transmitter : ACM engine determines the ACM profile according to the working Rx ACM indications only; - Maximum Capacity (default): Working Rx ACM engine is aware of the ACM profile requests from the protection Rx ACM engine, and determines the highest ACM profile between the working and the protection links; - Maximum Protection : Working Rx ACM engine is aware of the protection Rx ACM engine's ACM profile requests, and determines the lowest ACM profile between the working and the protection links. |
| INT xfRLTEnhancedACMProtectionOperStatus | 1.3.6.1.4.1.193.81.3.4.5.1.14.1.12 | INTEGER | read-only | Status of the enhanched ACM protection engine, when ACM engine is configured either in maximum-troughtput or maximum-protection mode. Values: - notApplicable : when enhanced ACM protection mode is basic; - enhAcmProtActive : when the enhanced ACM engine is working and the highest ACM profile is selected between the working and the protection links; - enhAcmProtNotActive: when the enhanced ACM engine is not working. |
| xfRLTEncryptionTable | 1.3.6.1.4.1.193.81.3.4.5.1.15 | not-accessible | This table is used to handle Radio Link Encryption. | |
| xfRLTEncryptionEntry | 1.3.6.1.4.1.193.81.3.4.5.1.15.1 | not-accessible | An entry in the xfRLTEncryptionTable. | |
| I32 xfRLTEncryptionIndex | 1.3.6.1.4.1.193.81.3.4.5.1.15.1.1 | Integer32 | read-only | It represents the xfRLTEncryptionTable index and is the RLT entity logical index. |
| INT xfRLTEncryptionAdminStatus | 1.3.6.1.4.1.193.81.3.4.5.1.15.1.2 | INTEGER | read-write | This MO allows to enable/disable the Encryption of both control and traffic plain over the Radio Link hop. Values: - enable; - disable. Default: DISABLE. |
| INT xfRLTEncryptionOperStatus | 1.3.6.1.4.1.193.81.3.4.5.1.15.1.3 | INTEGER | read-only | This MO represents the Operative Status of the Encryption function over the Radio Link hop and refers to receiving direction. Therefore, it indicates if the receiving side is able or not able to correctly/successfully decipher the ciphered data stream transmitted from remote side.. The ecryption status can assume the values: - up: control and traffic plain are correctly deciphered; - down: control and traffic plain are not deciphered correctly/successfully, due to e.g. authentication failure, disturbance over the radio-hop. |
| STR xfRLTEncryptionMasterKey | 1.3.6.1.4.1.193.81.3.4.5.1.15.1.4 | DisplayString | read-write | This MO allows to define the Master Key used to initiate the Encryption operation. Master Key is hidden. |
| xfRadioLinkRltPmObjects | 1.3.6.1.4.1.193.81.3.4.5.2 | |||
| xfRLPMContinuousCounterTable | 1.3.6.1.4.1.193.81.3.4.5.2.1 | not-accessible | Table for RLT performance data. | |
| xfRLPMContinuousCounterEntry | 1.3.6.1.4.1.193.81.3.4.5.2.1.1 | not-accessible | An entry in the xfRLPMContinuousCounterTable. | |
| NUM xfPMTimeElapsed | 1.3.6.1.4.1.193.81.3.4.5.2.1.1.1 | PerfIntervalCount | read-only | The number of seconds that have elapsed since the beginning of the current error-measurement period. If the current interval exceeds the maximum value, the agent will return the maximum value. Reset by xfPMPerfReset. |
| PER xfPMCurrentES | 1.3.6.1.4.1.193.81.3.4.5.2.1.1.2 | PerfCurrentCount | read-only | This object shows the errored seconds. Reset by xfPMPerfReset. |
| PER xfPMCurrentSES | 1.3.6.1.4.1.193.81.3.4.5.2.1.1.3 | PerfCurrentCount | read-only | This object shows the severely errored seconds. Reset by xfPMPerfReset. |
| HCP xfPMCurrentBBE | 1.3.6.1.4.1.193.81.3.4.5.2.1.1.4 | HCPerfCurrentCount | read-only | This object shows the background block errors. Reset by xfPMPerfReset. |
| PER xfPMCurrentUAS | 1.3.6.1.4.1.193.81.3.4.5.2.1.1.5 | PerfCurrentCount | read-only | This object shows the unavailable seconds (or unavailable time). Reset by xfPMPerfReset. |
| HCP xfPMCurrentBB | 1.3.6.1.4.1.193.81.3.4.5.2.1.1.6 | HCPerfCurrentCount | read-only | This object shows the background blocks. Reset by xfPMPerfReset. |
| INT xfPMPerfReset | 1.3.6.1.4.1.193.81.3.4.5.2.1.1.7 | INTEGER | read-write | This object is used to reset the performance counters: - Elapsed Time, ES, SES, BBE, BB - PM ACM - ETSI - EN 301 129 (TLTS, RLTS, ...) current/interval 15m/24h - Max and Min XPI/MSE current/interval 15m/24h It can be also set when the RAU is not present. Near end access: read-write. |
| PER xfPMCurrentESR | 1.3.6.1.4.1.193.81.3.4.5.2.1.1.8 | PerfCurrentCount | read-only | The ratio of ES to total seconds in available time during a fixed measurement interval. Reset by xfPMPerfReset. |
| PER xfPMCurrentSESR | 1.3.6.1.4.1.193.81.3.4.5.2.1.1.9 | PerfCurrentCount | read-only | The ratio of SES to total seconds in available time during a fixed measurement interval. Reset by xfPMPerfReset. |
| HCP xfPMCurrentBBER | 1.3.6.1.4.1.193.81.3.4.5.2.1.1.10 | HCPerfCurrentCount | read-only | The ratio of Background Block Errors (BBE) to total blocks in available time during a fixed measurement interval. Reset by xfPMPerfReset. |
| xfRLPMACMConfigTable | 1.3.6.1.4.1.193.81.3.4.5.2.2 | not-accessible | Alarm threshold values for RL PM. | |
| xfRLPMACMConfigEntry | 1.3.6.1.4.1.193.81.3.4.5.2.2.1 | not-accessible | Entry in the xfRLPMACMConfigTable | |
| I32 xfPMACMSetThreshold15m | 1.3.6.1.4.1.193.81.3.4.5.2.2.1.1 | Integer32 | read-write | The 15 minute set threshold for minimum modulation. Near end access: read-write. Far end access: no access. Default value is 180. |
| I32 xfPMACMSetThreshold24h | 1.3.6.1.4.1.193.81.3.4.5.2.2.1.2 | Integer32 | read-write | The 24 hour set threshold for minimum modulation. Near end access: read-write. Far end access: no access. Default value is 1500. |
| I32 xfPMACMResetThreshold15m | 1.3.6.1.4.1.193.81.3.4.5.2.2.1.3 | Integer32 | read-write | The 15 minute reset threshold for minimum modulation. Near end access: read-write. Far end access: no access. Default value is 20. |
| BIT xfPMACMStatus | 1.3.6.1.4.1.193.81.3.4.5.2.2.1.4 | Bits | read-only | It reports threshold crossing alarm status: - acm15m: ACM 15 min threshold crossing: ACM has been in the lowest configured profile for a number of seconds exceeding the configured 15 min threshold. - acm24h: ACM 24 hour threshold crossing: ACM has been in the lowest configured profile for a number of seconds exceeding the configured 24 hour threshold. |
| BIT xfPMACMValidData | 1.3.6.1.4.1.193.81.3.4.5.2.2.1.5 | Bits | read-only | It reports which ACM's PM data are valid. |
| xfRLPMACMCurrent24hTable | 1.3.6.1.4.1.193.81.3.4.5.2.3 | not-accessible | ACM-based counters for current 24h table. | |
| xfRLPMACMCurrent24hEntry | 1.3.6.1.4.1.193.81.3.4.5.2.3.1 | not-accessible | Entry in the xfRLPMACMCurrent24hTable. | |
| PER xfPMACMCurrent24h4QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.1 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h4QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.2 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h4QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.3 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h16QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.4 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h16QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.5 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h16QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.6 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h32QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.7 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h32QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.8 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h32QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.9 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h64QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.10 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h64QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.11 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h64QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.12 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h128QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.13 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h128QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.14 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h128QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.15 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h256QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.16 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h256QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.17 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h256QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.18 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h512QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.19 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h512QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.20 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h512QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.21 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h1024QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.22 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h1024QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.23 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h1024QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.24 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h2048QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.25 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h2048QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.26 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h2048QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.27 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h4096QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.28 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h4096QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.29 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h4096QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.30 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h8192QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.31 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h8192QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.32 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h8192QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.33 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h16384QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.34 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h16384QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.35 | PerfCurrentCount | read-only | Valid time since reset. |
| PER xfPMACMCurrent24h16384QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.3.1.36 | PerfCurrentCount | read-only | Valid time since reset. |
| xfRLPMACMInterval24hTable | 1.3.6.1.4.1.193.81.3.4.5.2.4 | not-accessible | ACM-based counters for interval 24h table. | |
| xfRLPMACMInterval24hEntry | 1.3.6.1.4.1.193.81.3.4.5.2.4.1 | not-accessible | Entry in the xfRLPMACMInterval24hTable. | |
| NUM xfPMACMInterval24h4QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.1 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h4QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.2 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h4QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.3 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h16QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.4 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h16QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.5 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h16QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.6 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h32QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.7 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h32QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.8 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h32QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.9 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h64QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.10 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h64QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.11 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h64QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.12 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h128QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.13 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h128QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.14 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h128QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.15 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h256QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.16 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h256QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.17 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h256QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.18 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h512QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.19 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h512QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.20 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h512QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.21 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h1024QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.22 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h1024QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.23 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h1024QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.24 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h2048QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.25 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h2048QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.26 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h2048QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.27 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h4096QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.28 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h4096QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.29 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h4096QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.30 | PerfIntervalCount | read-only | Interval count. |
| T/F xfPMACMInterval24hValidData | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.31 | TruthValue | read-only | This variable indicates whether the data for this interval is valid. |
| NUM xfPMACMInterval24h8192QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.32 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h8192QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.33 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h8192QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.34 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h16384QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.35 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h16384QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.36 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval24h16384QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.4.1.37 | PerfIntervalCount | read-only | Interval count. |
| xfRLPMACMCurrent15mTable | 1.3.6.1.4.1.193.81.3.4.5.2.5 | not-accessible | ACM-based counters for current 15m table. | |
| xfRLPMACMCurrent15mEntry | 1.3.6.1.4.1.193.81.3.4.5.2.5.1 | not-accessible | Entry in the table. | |
| PER xfPMACMCurrent15m4QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.1 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m4QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.2 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m4QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.3 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m16QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.4 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m16QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.5 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m16QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.6 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m32QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.7 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m32QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.8 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m32QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.9 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m64QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.10 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m64QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.11 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m64QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.12 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m128QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.13 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m128QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.14 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m128QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.15 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m256QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.16 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m256QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.17 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m256QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.18 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m512QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.19 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m512QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.20 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m512QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.21 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m1024QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.22 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m1024QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.23 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m1024QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.24 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m2048QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.25 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m2048QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.26 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m2048QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.27 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m4096QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.28 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m4096QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.29 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m4096QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.30 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m8192QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.31 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m8192QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.32 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m8192QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.33 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m16384QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.34 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m16384QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.35 | PerfCurrentCount | read-only | Valid interval time since reset. |
| PER xfPMACMCurrent15m16384QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.5.1.36 | PerfCurrentCount | read-only | Valid interval time since reset. |
| xfRLPMACMInterval15mTable | 1.3.6.1.4.1.193.81.3.4.5.2.6 | not-accessible | ACM-based counters for interval 15m table. | |
| xfRLPMACMInterval15mEntry | 1.3.6.1.4.1.193.81.3.4.5.2.6.1 | not-accessible | Entry in the table. | |
| I32 xfPMACMInterval15mIntervalNumber | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.1 | Integer32 | read-only | A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. |
| NUM xfPMACMInterval15m4QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.2 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m4QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.3 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m4QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.4 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m16QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.5 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m16QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.6 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m16QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.7 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m32QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.8 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m32QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.9 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m32QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.10 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m64QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.11 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m64QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.12 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m64QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.13 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m128QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.14 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m128QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.15 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m128QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.16 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m256QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.17 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m256QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.18 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m256QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.19 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m512QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.20 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m512QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.21 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m512QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.22 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m1024QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.23 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m1024QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.24 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m1024QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.25 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m2048QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.26 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m2048QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.27 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m2048QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.28 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m4096QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.29 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m4096QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.30 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m4096QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.31 | PerfIntervalCount | read-only | Interval count. |
| T/F xfPMACMInterval15mValidData | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.32 | TruthValue | read-only | This variable indicates whether the data for this interval is valid. |
| NUM xfPMACMInterval15m8192QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.33 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m8192QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.34 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m8192QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.35 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m16384QAMStrong | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.36 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m16384QAMStd | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.37 | PerfIntervalCount | read-only | Interval count. |
| NUM xfPMACMInterval15m16384QAMLight | 1.3.6.1.4.1.193.81.3.4.5.2.6.1.38 | PerfIntervalCount | read-only | Interval count. |
| xfRLPMMimoCurrentTable | 1.3.6.1.4.1.193.81.3.4.5.2.7 | not-accessible | Table for RLT MIMO Current performance data. | |
| xfRLPMMimoCurrentEntry | 1.3.6.1.4.1.193.81.3.4.5.2.7.1 | not-accessible | An entry in the xfRLPMMimoCurrentTable. | |
| INT xfPMPerfCurrentEta | 1.3.6.1.4.1.193.81.3.4.5.2.7.1.1 | INTEGER | read-only | Performance Monitoring for Current MIMO Eta Value. |
| INT xfPMPerfEtaMinLast7days | 1.3.6.1.4.1.193.81.3.4.5.2.7.1.2 | INTEGER | read-only | Indicate ETA Min level for the last 7 days. |
| INT xfPMPerfEtaMaxLast7days | 1.3.6.1.4.1.193.81.3.4.5.2.7.1.3 | INTEGER | read-only | Indicate ETA Max level for the last 7 days. |
| xfRLPMMimoCurrent24hTable | 1.3.6.1.4.1.193.81.3.4.5.2.8 | not-accessible | Counters for Eta in current 24h. | |
| xfRLPMMimoCurrent24hEntry | 1.3.6.1.4.1.193.81.3.4.5.2.8.1 | not-accessible | Entry in the xfRLPMMimoCurrent24hTable. | |
| C32 xfPMPerfCurrent24hElapsedTime | 1.3.6.1.4.1.193.81.3.4.5.2.8.1.1 | Counter32 | read-only | The number of seconds that have elapsed since the beginning of the current error-measurement period. |
| INT xfPMPerfCurrent24hEtaMin | 1.3.6.1.4.1.193.81.3.4.5.2.8.1.2 | INTEGER | read-only | Performance Monitoring for MIMO Eta Min Value in Current 24h. |
| INT xfPMPerfCurrent24hEtaMax | 1.3.6.1.4.1.193.81.3.4.5.2.8.1.3 | INTEGER | read-only | Performance Monitoring for Current MIMO 24h Eta Max Value. |
| xfRLPMMimoInterval24hTable | 1.3.6.1.4.1.193.81.3.4.5.2.9 | not-accessible | Performance Monitoring for MIMO Eta Min Value in Interval of 24h. | |
| xfRLPMMimoInterval24hEntry | 1.3.6.1.4.1.193.81.3.4.5.2.9.1 | not-accessible | Entry in the xfRLPMMimoInterval24hTable. | |
| INT xfPMPerfInterval24hValidData | 1.3.6.1.4.1.193.81.3.4.5.2.9.1.1 | INTEGER | read-only | This variable indicates whether the data for this interval is valid. |
| INT xfPMPerfInterval24hEtaMin | 1.3.6.1.4.1.193.81.3.4.5.2.9.1.2 | INTEGER | read-only | Performance Monitoring for MIMO Eta Min Value in Interval of 24h. |
| INT xfPMPerfInterval24hEtaMax | 1.3.6.1.4.1.193.81.3.4.5.2.9.1.3 | INTEGER | read-only | Performance Monitoring for MIMO Eta Max Value in Interval of 24h. |
| xfRLPMMimoCurrent15mTable | 1.3.6.1.4.1.193.81.3.4.5.2.10 | not-accessible | Counters for Eta MIMO Current 15m table. | |
| xfRLPMMimoCurrent15mEntry | 1.3.6.1.4.1.193.81.3.4.5.2.10.1 | not-accessible | Entry in the table. | |
| C32 xfPMPerfCurrent15mElapsedTime | 1.3.6.1.4.1.193.81.3.4.5.2.10.1.1 | Counter32 | read-only | The number of seconds that have elapsed since the beginning of the current error-measurement period |
| INT xfPMPerfCurrent15mEtaMin | 1.3.6.1.4.1.193.81.3.4.5.2.10.1.2 | INTEGER | read-only | Performance Monitoring for MIMO Eta Min Value in Current 15m. |
| INT xfPMPerfCurrent15mEtaMax | 1.3.6.1.4.1.193.81.3.4.5.2.10.1.3 | INTEGER | read-only | Performance Monitoring for MIMO Eta Max Value in Current 15m. |
| xfRLPMMimoInterval15mTable | 1.3.6.1.4.1.193.81.3.4.5.2.11 | not-accessible | Counters for Eta MIMO for Interval 15m. | |
| xfRLPMMimoInterval15mEntry | 1.3.6.1.4.1.193.81.3.4.5.2.11.1 | not-accessible | Entry in the table. | |
| INT xfPMPerfInterval15mIntervalNumber | 1.3.6.1.4.1.193.81.3.4.5.2.11.1.1 | INTEGER | read-only | A number between 1 and 96, which identifies the interval for which the set of statistics is available. The interval identified by 1 is the most recently completed 15 minute interval, and the interval identified by N is the interval immediately preceding the one identified by N-1. |
| INT xfPMPerfInterval15mEtaMin | 1.3.6.1.4.1.193.81.3.4.5.2.11.1.2 | INTEGER | read-only | Performance Monitoring for MIMO Eta Min Value in Interval 15m. |
| INT xfPMPerfInterval15mEtaMax | 1.3.6.1.4.1.193.81.3.4.5.2.11.1.3 | INTEGER | read-only | Performance Monitoring for MIMO Eta Max Value in Interval 15m. |
| INT xfPMPerfInterval15mValidData | 1.3.6.1.4.1.193.81.3.4.5.2.11.1.4 | INTEGER | read-only | This variable indicates whether the data for this interval is valid. |
| xfRadioLinkRltConformance | 1.3.6.1.4.1.193.81.3.4.5.3 | |||
| xfRadioLinkRltCompliances | 1.3.6.1.4.1.193.81.3.4.5.3.1 | |||
| xfRadioLinkRltFullCompliance | 1.3.6.1.4.1.193.81.3.4.5.3.1.1 | The compliance statement for SNMP entities which implement everything. | ||
| xfRadioLinkRltGroups | 1.3.6.1.4.1.193.81.3.4.5.3.2 | |||
| xfRadioLinkRltCompleteGroup | 1.3.6.1.4.1.193.81.3.4.5.3.2.1 | A collection of all current objects in this MIB module |
RFC description
Manages Radio Link Terminal (RLT) and Carrier Termination for Ericsson MINI-LINK TN radio links with dual carrier support.
Start monitoring Ericsson MINI-LINK microwave radio equipment with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.