XF-RADIOLINK-PTP-RADIO-MIB

All MIBs › XF-RADIOLINK-PTP-RADIO-MIB

Organization: Ericsson AB

Last Updated: 2020-09-22

Category: Ericsson Radio Link

Description:

Manages Ericsson XF PTP radio link RF parameters, transmit power, and receive signal level.

Imported Objects

entPhysicalIndex

OBJECT-TYPE

From IF-MIB

ifIndex

OBJECT-TYPE

From SNMPv2-CONF

MODULE-COMPLIANCE
OBJECT-GROUP

From SNMPv2-SMI

Integer32
MODULE-IDENTITY
OBJECT-TYPE
Unsigned32

From SNMPv2-TC

DisplayString
TEXTUAL-CONVENTION

From XF-RADIOLINK-PTP-TERMINAL-MIB

xfTermRowIndex

OBJECT-TYPE

From XF-TOP-MIB

xfRadioLink

OBJECT-IDENTITY

What Is XF-RADIOLINK-PTP-RADIO-MIB?

XF-RADIOLINK-PTP-RADIO-MIB is an Ericsson MIB for the XF family of point-to-point microwave radio link units (RAUs) used in mobile backhaul networks, defining objects for configuring and monitoring the radio-layer parameters of the link. It exposes RF-level data such as transmit power and receive signal level for the point-to-point radio path. Its central purpose is hardware status monitoring of the radio unit - tracking transmit power output and received signal strength lets operators detect fading, antenna misalignment, or hardware degradation on a microwave backhaul link before it causes a service outage. As a radio-specific MIB it likely complements Ericsson's broader XF/MINI-LINK equipment MIBs that cover chassis/unit inventory and alarms. It is deployed in mobile backhaul networks using Ericsson XF/MINI-LINK point-to-point microwave radio equipment. Engineers can download the XF-RADIOLINK-PTP-RADIO-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in XF-RADIOLINK-PTP-RADIO-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

What Can Be Monitored

transmit power level
receive signal level (RSL)

Supported Devices

Ericsson XF/MINI-LINK point-to-point microwave radio

Monitoring Examples

No sample objects were provided for this module, so specific object identifiers cannot be cited here. Based on the module description, the realistic monitoring use is polling RF transmit power and receive signal level (RSL) per radio link to detect a degrading microwave path - for example a steadily falling RSL reading would warn of antenna misalignment or worsening weather-related fade well before the link drops - but no concrete table/object names can be honestly confirmed from the data given.

OIDs

OID symbolic	OID numeric	Type	Access	Description
xfRadioLinkPtpRadioCompleteGroup	1.3.6.1.4.1.193.81.3.4.3.2.2.1			A collection of all current objects in this MIB module.
xfRadioLinkPtpRadioCompliances	1.3.6.1.4.1.193.81.3.4.3.2.1
xfRadioLinkPtpRadioConformance	1.3.6.1.4.1.193.81.3.4.3.2
xfRADIOLINKPTPRADIOFullCompliance	1.3.6.1.4.1.193.81.3.4.3.2.1.1			The compliance statement for SNMP entities which implement everything.
xfRadioLinkPtpRadioGroups	1.3.6.1.4.1.193.81.3.4.3.2.2
xfRadioLinkPtpRadioMIB	1.3.6.1.4.1.193.81.3.4.3			This MIB defines objects for point-to-point Radio Link RAUs.
xfRadioLinkPtpRadioObjects	1.3.6.1.4.1.193.81.3.4.3.1
BIT xfRAUAlarmStatus	1.3.6.1.4.1.193.81.3.4.3.1.1.1.1	Bits	read-only	This object shows the alarm status of the radio unit. atpcCability - The terminal is configured for ATPC, but the radio does not support ATPC. This alarm is activated only if ATPC is turned on (any direction). sdcHwErrorMain - Received RF input signal level for Main path (of SDC TRX) has dropped below the threshold for the receiver. sdcHwErrorDiv - Received RF input signal level for Diversity path (of SDC TRX) has dropped below the threshold for the receiver. sdcDadeCalMismatch - A TRX is connected and its Serial Number doesn't match with the serial number stored into MO xfTRXSdcSerialNumber. insufficientResourceRauXpic - Connected RAU is missing capabilities for XPIC. companionRauMismatch - Connected RAU does not match with the companion one, either in 1+1 RLP or XPIC.
RAU xfRAUAtpcCapability	1.3.6.1.4.1.193.81.3.4.3.1.1.1.3	RAUAtpcCapability	read-only	This object indicates if the radio unit supports ATPC or not.
INT xfRauAtpcVersion	1.3.6.1.4.1.193.81.3.4.3.1.1.1.12	INTEGER	read-only	This object represents the RAU ATPC version.
BOO xfRauBoosterCapability	1.3.6.1.4.1.193.81.3.4.3.1.1.1.13	BoosterCapability	read-only	This object represents the Booster capability for a link.
I32 xfRauBoosterSelectedIndex	1.3.6.1.4.1.193.81.3.4.3.1.1.1.14	Integer32	read-write	This object represents the Booster selected index for a link.
xfRAUCapabilityEntry	1.3.6.1.4.1.193.81.3.4.3.1.4.1		not-accessible	An entry in xfRAUCapabilityTable.
xfRAUCapabilityTable	1.3.6.1.4.1.193.81.3.4.3.1.4		not-accessible	Table for RAU capability information. Table indexed with entPhysicalIndex and xfTermRowIndex.
INT xfRAUCarrierMode	1.3.6.1.4.1.193.81.3.4.3.1.4.1.4	INTEGER	read-only	Radio carrier mode.
RAU xfRAUChannelModulation	1.3.6.1.4.1.193.81.3.4.3.1.4.1.2	RAUModulation	read-only	This object shows the modulation. Values: cqpsk(2) CQPSK qam16(3) 16-QAM qam128(4) 128-QAM qam32(5) 32-QAM qam64(6) 64-QAM qam4(7) 4-QAM qam8(8) 8-QAM qam256(9) 256-QAM qam512(10) 512-QAM qam1024(11) 1024-QAM
RAU xfRAUChannelSpacing	1.3.6.1.4.1.193.81.3.4.3.1.4.1.1	RAUChannelSpacingCapability	read-only	Channel spacing. ETSI: 3.5, 7, 14, 28, 40, 56 MHz ANSI: 10, 20, 30, 40, 50 MHz
xfRAUEntry	1.3.6.1.4.1.193.81.3.4.3.1.1.1		not-accessible	An entry in xfRadioTable.
U32 xfRAUFrequencyband	1.3.6.1.4.1.193.81.3.4.3.1.1.1.6	Unsigned32	read-only	This object shows the frequency band for the radio unit.
INT xfRAULocalCtrlCapability	1.3.6.1.4.1.193.81.3.4.3.1.1.1.4	INTEGER	read-only	This object indicates if the radio unit supports local transmit power control or not.
RAU xfRAUModCapability	1.3.6.1.4.1.193.81.3.4.3.1.1.1.5	RAUModCapability	read-only	This object shows the modulation methods supported by the radio unit.
OCT xfRAUNotes	1.3.6.1.4.1.193.81.3.4.3.1.1.1.11	OCTET STRING	read-write	You can add information in this description field, for example polarization, antenna type or logging a site visit.
INT xfRAUProtectionPath	1.3.6.1.4.1.193.81.3.4.3.1.1.1.9	INTEGER	read-only	This object indicates what radio path the radio belongs to.
RAU xfRAURfLoopAvailable	1.3.6.1.4.1.193.81.3.4.3.1.1.1.2	RAURfLoopAvailable	read-only	This object inidicates if RF loop is available in radio unit.
INT xfRAURxCapability	1.3.6.1.4.1.193.81.3.4.3.1.1.1.10	INTEGER	read-only	This object indicates if the radio unit support RX configuration.
RAU xfRAUSpectrumEfficiencyClass	1.3.6.1.4.1.193.81.3.4.3.1.4.1.3	RauSec	read-only	Spectrum Efficiency Class: other(1), unknown sec2(2), Spectrum eff. Class 2 sec3(3), Spectrum eff. Class 3 sec4L(4), Spectrum eff. Class 4L sec4H(5), Specturm eff. Class 4H sec5A(6), Spectrum eff. Class 5A sec5B(7), Spectrum eff. Class 5B sec6A(8), Spectrum eff. Class 6A sec6B(9) Spectrum eff. Class 6B
U32 xfRAUSubBand	1.3.6.1.4.1.193.81.3.4.3.1.1.1.7	Unsigned32	read-write	This object shows the sub band (Index) for the radio unit.
xfRAUSubBandEntry	1.3.6.1.4.1.193.81.3.4.3.1.5.1		not-accessible	An entry in xfRAUSubBandTable.
U32 xfRAUSubBandIndex	1.3.6.1.4.1.193.81.3.4.3.1.5.1.1	Unsigned32	read-only	An index for the specific RAU Sub-Band available index range.
U32 xfRAUSubBandRange	1.3.6.1.4.1.193.81.3.4.3.1.5.1.2	Unsigned32	read-only	This object shows the RAU Sub-Band available index range [0..255].
xfRAUSubBandTable	1.3.6.1.4.1.193.81.3.4.3.1.5		not-accessible	Table for RAU Sub-Band index capability. Table indexed with entPhysicalIndex and xfRAUSubBandIndex.
xfRAUTable	1.3.6.1.4.1.193.81.3.4.3.1.1		not-accessible	Table for Radiolink point-to-point radios managed objects. Table indexed with entPhysicalIndex.
I32 xfRAUTemperature	1.3.6.1.4.1.193.81.3.4.3.1.1.1.8	Integer32	read-only	This object shows the temperature, in degree Celsius, inside the radio unit.
BIT xfRFAlarms	1.3.6.1.4.1.193.81.3.4.3.1.2.1.10	Bits	read-only	This TC enumerates the alarms for RF interface. txFrequency - Transmitter frequency synthesizer loop is unlocked. rxFrequency - Receiver frequency synthesizer loop is unlocked. rfOutputLevel - Major degradation of transmitter output power is detected. rxAfc - The frequency of the received signal is outside the range of the Automatic Frequency Control in the RAU receiver. rfInputLevel - Receiver RF input signal level has dropped below the threshold for the receiver. rfInputThreshold - The RF input level has dropped below the xfRFInputAlarmThreshold. rfOutputLevelATPC - The transmitter output power has been continuously at 'Patpc,max' for too long. This can occur due to several reasons: * The operator has set 'Patpc,max' too low. * The hop attenuation has increased (steady-state). * The transmitter PA is v. * The LNA in Rx is deteriorating.
ATP xfRFAtpcFallbackEnable	1.3.6.1.4.1.193.81.3.4.3.1.8.1.40	ATPCFallbackEnable	read-write	Enable/disable ATPCFallback.
RFO xfRFAtpcFallbackOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.39	RfOutputPower	read-write	This object sets output power (in dBm) in ATPCFallback mode, for radio contained in the Carrier Termination. 255 indicates invalid value.
I32 xfRFAtpcFallbackTimer	1.3.6.1.4.1.193.81.3.4.3.1.8.1.41	Integer32	read-write	This object specifies how long the output power can be at (ATPC, MAX) before ATPC fallback is triggered. Default value: ETSI 15 min, ANSI 5 min.
I32 xfRFAtpcMaxOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.6	Integer32	read-write	This object sets/shows the ATPC maximum output power in dBm for radio contained in the radio terminal. Value 254 indicates that the power is set to maximum. Default value: 254.
I32 xfRFAtpcMinInputPowerFar	1.3.6.1.4.1.193.81.3.4.3.1.3.1.7	Integer32	read-only	This object shows the ATPC minimum input target power level for far end radio.
I32 xfRFAtpcMinOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.5	Integer32	read-only	This object shows the minimum output power in dBm in ATPC. mode for radio contained in the radio terminal.
I32 xfRFAtpcSelectedInputPowerFar	1.3.6.1.4.1.193.81.3.4.3.1.3.1.8	Integer32	read-write	This object sets/shows the ATPC selected input target level for far end radio. Default value: -30.
I32 xfRfAtpcTargetInputPowerFE	1.3.6.1.4.1.193.81.3.4.3.1.8.1.6	Integer32	read-write	ATPC target input power on Far End side. Default value: -30.
I32 xfRFAttenuator	1.3.6.1.4.1.193.81.3.4.3.1.3.1.9	Integer32	read-write	This object sets/shows the value in dBm for fixed attenuator mounted in antenna. Default value: 0.
INT xfRfAvailableOutputPowerType	1.3.6.1.4.1.193.81.3.4.3.1.8.1.32	INTEGER	read-only	This object reports the output power capability of the RAU: - standardPower - highPower
U32 xfRFBaseRxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.2.1.2	Unsigned32	read-only	This object shows the Rx frequency in KHz when frequency. step number is 0
U32 xfRFBaseTxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.2.1.1	Unsigned32	read-only	This object shows the Tx frequency in KHz when frequency step number is 0.
BOO xfRFBoosterCapability	1.3.6.1.4.1.193.81.3.4.3.1.3.1.45	BoosterCapability	read-only	Value of Booster capability according to the system
I32 xfRFBoosterGain	1.3.6.1.4.1.193.81.3.4.3.1.3.1.43	Integer32	read-only	Value of the Gain of the Booster
STR xfRFBoosterHWRevision	1.3.6.1.4.1.193.81.3.4.3.1.3.1.47	DisplayString	read-write	HW Revision of the Booster connected to the specific RF IF
I32 xfRFBoosterMaxInputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.44	Integer32	read-only	Value of the Max Input Power admitted towards the Booster
STR xfRFBoosterProductNumber	1.3.6.1.4.1.193.81.3.4.3.1.3.1.46	DisplayString	read-write	Product Number of the Booster connected to the specific RF IF
RFI xfRFCurrentInputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.7	RfInputPower	read-only	RF input level. Value is in 1/10 dBm. Domain: [-20.0 .. -99.9 dBm].
RFI xfRFCurrentInputPowerSdcDiv	1.3.6.1.4.1.193.81.3.4.3.1.8.1.36	RfInputPower	read-only	This object shows RF input level for SDC Diversity path = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. 0 (zero) indicates invalid value (e.g. SDC not available).
RFI xfRFCurrentInputPowerSdcMain	1.3.6.1.4.1.193.81.3.4.3.1.8.1.35	RfInputPower	read-only	This object shows RF input level for SDC Main path = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. 0 (zero) indicates invalid value (e.g. SDC not available).
RFO xfRFCurrentOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.3	RfOutputPower	read-only	Current output power in dBm. 255 indicates invalid value.
U32 xfRFCurrentStepNumber	1.3.6.1.4.1.193.81.3.4.3.1.2.1.6	Unsigned32	read-write	This object sets/shows the frequency step number. 0 = frequency not yet defined. For Classic RAUs, TX and RX frequencies can not be set individually. The span between them is always fixed and depends on different frequency and sub band. - To calculate step number for TX and RX, use the following formulas: New step number = (TX frequency - XfRAUBaseTxFrequency) / XfRAUStepSize New step number = (RX frequency - xfRAUBaseRxFrequency) / XfRAUStepSize - To calculate TX and RX frequencies, use the following formulas: TX frequency = XfRAUBaseTxFrequency + XfRAUCurrentStepNumber * XfRAUStepSize RX frequency = XfRAUBaseRxFrequency + XfRAUCurrentStepNumber * XfRAUStepSize For Agile RAUs, the TX and RX frequencies can be set individually. Above formulas are only valid for TX frequency. For RX frequency, xfRFCurrentStepNumberRx must be used. Default value: 0
U32 xfRFCurrentStepNumberRx	1.3.6.1.4.1.193.81.3.4.3.1.2.1.15	Unsigned32	read-write	This object sets/shows the RX frequency step number for Agile RAUs. 0 = frequency not yet defined. - To calculate step number for RX, use the following formula: New step number Rx = (RX frequency - xfRAUBaseRxFrequency) / XfRAUStepSizeRx - To calculate RX frequency, use the following formula: RX frequency = XfRAUBaseRxFrequency + XfRAUCurrentStepNumberRx * XfRAUStepSizeRx Default value: 0
INT xfRFDegradationAgc	1.3.6.1.4.1.193.81.3.4.3.1.9.1.11	INTEGER	read-write	This object manage IfCable Degradation Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
U32 xfRFDegradationCeaseTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.13	Unsigned32	read-write	This object handles Cease Threshold for Degradation Alarm. 1 = Default value (0.1). - To calculate threshold use the following formula: SetTh/10. Default value: 1 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFDegradationSetTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.12	Unsigned32	read-write	This object handles Set Threshold for Degradation Alarm. 2 = Default value (0.2). - To calculate threshold use the following formula: SetTh/10. Default value: 2 (dB/10) Near end access: read-write. Far end access: no access.
INT xfRFDegradationTrigger	1.3.6.1.4.1.193.81.3.4.3.1.9.1.25	INTEGER	read-only	This object manage IfCable Degradation Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
I32 xfRFDegradationValue	1.3.6.1.4.1.193.81.3.4.3.1.9.1.20	Integer32	read-only	This object handles the value calculated on 24h for Degradation Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access.
INT xfRFDuplexConfig	1.3.6.1.4.1.193.81.3.4.3.1.2.1.17	INTEGER	read-write	This object enables setting of duplex frequency for the RAU. It is always disabled(3) and can not be overwritten if xfRFDuplexType = fixed(2).
I32 xfRFDuplexDistance	1.3.6.1.4.1.193.81.3.4.3.1.2.1.18	Integer32	read-write	This object is aimed to select the duplex distance for the RAU. It can only be set if xfRFDuplexConfig = enabled(2), so that: xfRFDuplexDistance = Tx Frequency - Rx Frequency Otherwise, it is automatically filled on the basis of Tx and Rx frequency settings, and can not be overwritten.
INT xfRFDuplexType	1.3.6.1.4.1.193.81.3.4.3.1.2.1.16	INTEGER	read-only	This object tells the duplex frequency mode for the RAU: - fixed: Tx frequency only can be set by operator, Rx frequency is automatically set on the basis of (fixed) RAU duplex frequency - variable: duplex frequency can be configured by operator
xfRFIFCableMonitoringEntry	1.3.6.1.4.1.193.81.3.4.3.1.9.1		not-accessible	An entry in the xfRFIFCableMonitoringTable.
xfRFIFCableMonitoringTable	1.3.6.1.4.1.193.81.3.4.3.1.9		not-accessible	Table for Radiolink point-to-point radios RF IF Cable Monitoring managed objects. Table indexed with ifIndex.
INT xfRFIFCMStatus	1.3.6.1.4.1.193.81.3.4.3.1.9.1.1	INTEGER	read-write	This object manage IfCable Monitoring Status. Default value: disable(2). Near end access: read-write. Far end access: no access.
xfRFIFEntry	1.3.6.1.4.1.193.81.3.4.3.1.2.1		not-accessible	An entry in the xfRFIFTable.
xfRfIfPowerEntry	1.3.6.1.4.1.193.81.3.4.3.1.8.1		not-accessible	An entry in the xfRfIfPowerTable.
xfRfIfPowerTable	1.3.6.1.4.1.193.81.3.4.3.1.8		not-accessible	Table for Radio Link RAU managed objects. Table indexed with ifIndex.
xfRFIFTable	1.3.6.1.4.1.193.81.3.4.3.1.2		not-accessible	Table for Radiolink point-to-point radios RF IF managed objects. Table indexed with ifIndex.
I32 xfRFInputAlarmThreshold	1.3.6.1.4.1.193.81.3.4.3.1.8.1.13	Integer32	read-write	RF input level threshold. Default value: -93.
INT xfRFInputPowerReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.12	INTEGER	read-write	This object resets the registers for: - RF input power levels - input levels (i.e. RF power, MSE and XPI) in the next 7 days period of time.
INT xfRFLoopEnable	1.3.6.1.4.1.193.81.3.4.3.1.2.1.9	INTEGER	read-write	This object manage RF loop. Default value: disable(3). Near end access: read-write. Far end access: no access.
INT xfRFMarginAgc	1.3.6.1.4.1.193.81.3.4.3.1.9.1.14	INTEGER	read-write	This object manage IfCable Margin Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
U32 xfRFMarginCeaseTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.16	Unsigned32	read-write	This object handles Cease Threshold for Margin Alarm. 60 = Default value (6). - To calculate threshold use the following formula: SetTh/10. Default value: 60 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFMarginSetTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.15	Unsigned32	read-write	This object handles Set Threshold for Margin Alarm. 30 = Default value (3). - To calculate threshold use the following formula: SetTh/10. Default value: 30 (dB/10) Near end access: read-write. Far end access: no access.
INT xfRFMarginTrigger	1.3.6.1.4.1.193.81.3.4.3.1.9.1.26	INTEGER	read-only	This object manage IfCable Margin Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
I32 xfRFMarginValue	1.3.6.1.4.1.193.81.3.4.3.1.9.1.21	Integer32	read-only	This object handles the value calculated on 24h for Margin Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access.
RFI xfRFMaxInputPowerLast7Days	1.3.6.1.4.1.193.81.3.4.3.1.8.1.8	RfInputPower	read-only	Maximum RF input level in the last 7 days. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.
RFI xfRFMaxInputPowerSinceReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.10	RfInputPower	read-only	Maximum RF input level since reset. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.
I32 xfRFMaxMSELast7Days	1.3.6.1.4.1.193.81.3.4.3.1.3.1.38	Integer32	read-only	Indicate Max MSE level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.
RFO xfRfMaxOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.5	RfOutputPower	read-only	Maximum output power in dBm (provided by RAU). 255 indicates invalid value.
I32 xfRFMaxOutputPowerLast7Days	1.3.6.1.4.1.193.81.3.4.3.1.8.1.27	Integer32	read-only	This object shows maximum RF output level last 7 days. RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.
RFO xfRFMaxOutputPowerNotLimited	1.3.6.1.4.1.193.81.3.4.3.1.8.1.24	RfOutputPower	read-only	Max output power in dBm that the RAU can give if it is not power supply limited. 255 indicates invalid value.
INT xfRFMaxOutputPowerNotPossible	1.3.6.1.4.1.193.81.3.4.3.1.3.1.30	INTEGER	read-only	unknown(0) isPossible(1) Max output power is possible due to power supply limitations isNotPossible(2) Max output power is not possible due to power supply limitations
INT xfRfMaxOutputPowerPossible	1.3.6.1.4.1.193.81.3.4.3.1.8.1.25	INTEGER	read-only	possible(2): max output power is possible. notPossible(3): max output power is not possible, due to power supply limitations.
I32 xfRFMaxOutputPowerSinceReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.29	Integer32	read-only	This object shows maximum RF output level since reset RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.
I32 xfRFMaxXPILast7Days	1.3.6.1.4.1.193.81.3.4.3.1.3.1.40	Integer32	read-only	Indicate Max Cross-Polar Interference (XPI) level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.
I32 xfRFMeanInputPower1m	1.3.6.1.4.1.193.81.3.4.3.1.8.1.26	Integer32	read-only	This object shows RF input mean level for last minute. RF input level = value/10 dBm. Domain: [-99.9 ... -20.0 dBm] 0 (zero) indicates invalid value.
RFI xfRFMinInputPowerLast7Days	1.3.6.1.4.1.193.81.3.4.3.1.8.1.9	RfInputPower	read-only	Minimum RF input level in the last 7 days. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.
RFI xfRFMinInputPowerSinceReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.11	RfInputPower	read-only	Minimum RF input level since reset. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.
I32 xfRFMinMSELast7Days	1.3.6.1.4.1.193.81.3.4.3.1.3.1.39	Integer32	read-only	Indicate Min MSE level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.
RFO xfRfMinOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.4	RfOutputPower	read-only	Minimum output power in dBm (provided by RAU). 255 indicates invalid value.
I32 xfRFMinOutputPowerLast7Days	1.3.6.1.4.1.193.81.3.4.3.1.8.1.28	Integer32	read-only	This object shows minimum RF output level last 7 days. RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.
I32 xfRFMinOutputPowerSinceReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.30	Integer32	read-only	This object shows minimum RF output level since reset RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.
I32 xfRFMinXPILast7Days	1.3.6.1.4.1.193.81.3.4.3.1.3.1.41	Integer32	read-only	Indicate Min Cross-Polar Interference (XPI) level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.
INT xfRFOutlierAgc	1.3.6.1.4.1.193.81.3.4.3.1.9.1.2	INTEGER	read-write	This object manage IfCable Outlier Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
U32 xfRFOutlierCeaseTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.4	Unsigned32	read-write	This object handles Cease Threshold for Outlier Alarm. 2 = Default value (0.2). - To calculate threshold use the following formula: SetTh/10. Default value: 2 Near end access: read-write. Far end access: no access.
U32 xfRFOutlierSetTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.3	Unsigned32	read-write	This object handles Set Threshold for Outlier Alarm. 3 = Default value (0.3). - To calculate threshold use the following formula: SetTh/10. Default value: 3 Near end access: read-write. Far end access: no access.
INT xfRFOutlierTrigger	1.3.6.1.4.1.193.81.3.4.3.1.9.1.22	INTEGER	read-only	This object manage IfCable Outlier Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
I32 xfRFOutlierValue	1.3.6.1.4.1.193.81.3.4.3.1.9.1.17	Integer32	read-only	This object handles the value calculated on 24h for Outlier Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 Near end access: read-write. Far end access: no access.
RFO xfRFOutputPower1024QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.21	RfOutputPower	read-only	Output power for 1024QAM. 255 indicates invalid value.
RFO xfRFOutputPower128QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.18	RfOutputPower	read-only	Output power for 128QAM. 255 indicates invalid value.
RFO xfRfOutputPower16384QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.38	RfOutputPower	read-only	Output power for 16384QAM. 255 indicates invalid value.
RFO xfRFOutputPower16QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.15	RfOutputPower	read-only	Output power for 16QAM. 255 indicates invalid value.
RFO xfRfOutputPower2048QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.22	RfOutputPower	read-only	Output power for 2048QAM. 255 indicates invalid value.
RFO xfRFOutputPower256QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.19	RfOutputPower	read-only	Output power for 256QAM. 255 indicates invalid value.
RFO xfRFOutputPower32QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.16	RfOutputPower	read-only	Output power for 32QAM. 255 indicates invalid value.
RFO xfRfOutputPower4096QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.23	RfOutputPower	read-only	Output power for 4096QAM. 255 indicates invalid value.
RFO xfRFOutputPower4QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.14	RfOutputPower	read-only	Output power for 4QAM. 255 indicates invalid value.
RFO xfRFOutputPower512QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.20	RfOutputPower	read-only	Output power for 512QAM. 255 indicates invalid value.
RFO xfRFOutputPower64QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.17	RfOutputPower	read-only	Output power for 64QAM. 255 indicates invalid value.
RFO xfRfOutputPower8192QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.37	RfOutputPower	read-only	Output power for 8192QAM. 255 indicates invalid value.
I32 xfRFOutputPower8QAM	1.3.6.1.4.1.193.81.3.4.3.1.3.1.18	Integer32	read-only	Output power for 8QAM.
INT xfRFOutputPowerReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.31	INTEGER	read-write	This object reset the registers for the RF output level and All Time High level this seven days period and counters for the next seven days period of time.
xfRFPowerEntry	1.3.6.1.4.1.193.81.3.4.3.1.3.1		not-accessible	An entry in the xfRFPowerTable.
xfRFPowerTable	1.3.6.1.4.1.193.81.3.4.3.1.3		not-accessible	Table for Radiolink point-to-point radios managed objects. Table indexed with ifIndex.
INT xfRFRangeAgc	1.3.6.1.4.1.193.81.3.4.3.1.9.1.5	INTEGER	read-write	This object manage IfCable Range Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
U32 xfRFRangeCeaseTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.7	Unsigned32	read-write	This object handles Cease Threshold for Range Alarm. 20 = Default value (2). - To calculate threshold use the following formula: SetTh/10. Default value: 20 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFRangeSetTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.6	Unsigned32	read-write	This object handles Set Threshold for Range Alarm. 30 = Default value (3). - To calculate threshold use the following formula: SetTh/10. Default value: 30 (dB/10) Near end access: read-write. Far end access: no access.
INT xfRFRangeTrigger	1.3.6.1.4.1.193.81.3.4.3.1.9.1.23	INTEGER	read-only	This object manage IfCable Range Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
I32 xfRFRangeValue	1.3.6.1.4.1.193.81.3.4.3.1.9.1.18	Integer32	read-only	This object handles the value calculated on 24h for Range Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access.
I32 xfRFRtpcMaxOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.3	Integer32	read-only	This object shows the maximum output power in dBm including attenuator. Value -100 indicate that RAU Tx on is not possible due to power supply limitations.
I32 xfRFRtpcMinOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.2	Integer32	read-only	This object shows the minimum output power in dBm including attenuator. Value -100 indicate that RAU Tx on is not possible due to power supply limitations.
I32 xfRFRtpcSelectedOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.4	Integer32	read-write	This object set/shows the selected output power in dBm including attenuator. Value 254 indicates that the selected power is set to maximum. Default value: 254
RFO xfRfSelectedMaxOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.2	RfOutputPower	read-write	Maximum output power in dBm (selected by operator). Default value: 10 dBm.
RFO xfRfSelectedMinOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.1	RfOutputPower	read-write	Minimum output power in dBm (selected by operator). Default value: 10 dBm.
INT xfRfSelectedOutputPowerType	1.3.6.1.4.1.193.81.3.4.3.1.8.1.33	INTEGER	read-write	This object allows setting the output power type: - standardPower - highPower default: standardPower(2) When the type is set to highPower(3) a HP license key is required. If the license key is not present the capacity is limited to Basic Capacity. The output power can be configured as 'normal' without any impact from the HP license key (present or not). When the mode is standardPower(2) the availableMaxOutputPower is limited to 'max power' - 4 dB per modulation.
INT xfRFSpectrumDiagAdminStatus	1.3.6.1.4.1.193.81.3.4.3.1.6.1.1	INTEGER	read-write	RF Spectrum Diagnostics Admin Status
U32 xfRFSpectrumDiagChannelScanEstTime	1.3.6.1.4.1.193.81.3.4.3.1.6.1.3	Unsigned32	read-only	Estimated time in seconds for scanning one Channel Spacing at current RX frequency
U32 xfRFSpectrumDiagChannelSpacing	1.3.6.1.4.1.193.81.3.4.3.1.6.1.6	Unsigned32	read-only	Channel width measured by Spectrum Diagnostics
U32 xfRFSpectrumDiagCurrRxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.6.1.7	Unsigned32	read-only	Current value of Rx frequency
xfRFSpectrumDiagEntry	1.3.6.1.4.1.193.81.3.4.3.1.6.1		not-accessible	An entry in xfRFSpectrumDiagTable
U32 xfRFSpectrumDiagIdxCompanion1	1.3.6.1.4.1.193.81.3.4.3.1.6.1.10	Unsigned32	read-only	RF IF index for 1st companion carrier (0 if no companion)
U32 xfRFSpectrumDiagIdxCompanion2	1.3.6.1.4.1.193.81.3.4.3.1.6.1.11	Unsigned32	read-only	RF IF index for 2nd companion carrier (0 if no companion)
U32 xfRFSpectrumDiagIdxCompanion3	1.3.6.1.4.1.193.81.3.4.3.1.6.1.12	Unsigned32	read-only	RF IF index for 3rd companion carrier (0 if no companion)
U32 xfRFSpectrumDiagMaxRxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.6.1.9	Unsigned32	read-only	Maximum sub-band Rx frequency (RAU upper edge)
U32 xfRFSpectrumDiagMinRxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.6.1.8	Unsigned32	read-only	Minimum sub-band Rx frequency (RAU lower edge)
INT xfRFSpectrumDiagOperStatus	1.3.6.1.4.1.193.81.3.4.3.1.6.1.2	INTEGER	read-only	RF Spectrum Diagnostics Oper Status
U32 xfRFSpectrumDiagProgress	1.3.6.1.4.1.193.81.3.4.3.1.6.1.13	Unsigned32	read-only	Completed percentage of Spectrum Diagnostics scan
xfRFSpectrumDiagResultEntry	1.3.6.1.4.1.193.81.3.4.3.1.7.1		not-accessible	An entry in xfRFSpectrumDiagResultTable
U32 xfRFSpectrumDiagResultIndex	1.3.6.1.4.1.193.81.3.4.3.1.7.1.1	Unsigned32	read-only	Spectrum Diagnostics Scan Result Index
U32 xfRFSpectrumDiagResultRxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.7.1.2	Unsigned32	read-only	Spectrum Diagnostics Scan Result Rx frequency in kHz
I32 xfRFSpectrumDiagResultRxPower	1.3.6.1.4.1.193.81.3.4.3.1.7.1.3	Integer32	read-only	Spectrum Diagnostics Scan Result Rx Power value/10 dBm Domain: [-99.9 .. -20.0 dBm]
xfRFSpectrumDiagResultTable	1.3.6.1.4.1.193.81.3.4.3.1.7		not-accessible	Table of Spectrum Diagnostics scan results
STR xfRFSpectrumDiagScanDate	1.3.6.1.4.1.193.81.3.4.3.1.6.1.5	DisplayString	read-only	Date and time when scan (channel or sub-band) is completed, format: [YYYY]-[MM]-[DD]T[hh]:[mm]:[ss]
U32 xfRFSpectrumDiagSubBandScanEstTime	1.3.6.1.4.1.193.81.3.4.3.1.6.1.4	Unsigned32	read-only	Estimated time in seconds for scanning full Sub Band of connected RAU
xfRFSpectrumDiagTable	1.3.6.1.4.1.193.81.3.4.3.1.6		not-accessible	Table for RF Spectrum Diagnostics control and status
BIT xfRFStatus	1.3.6.1.4.1.193.81.3.4.3.1.2.1.11	Bits	read-only	This object shows the RAU status. rfLoop - Warns if RF-loop is enabled on RAU txOff - Warns if TX is manually set to off
INT xfRFStddevAgc	1.3.6.1.4.1.193.81.3.4.3.1.9.1.8	INTEGER	read-write	This object manage IfCable Stddev Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
U32 xfRFStddevCeaseTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.10	Unsigned32	read-write	This object handles Cease Threshold for Stddev Alarm. 20 = Default value (2). - To calculate threshold use the following formula: SetTh/10. Default value: 20 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFStddevSetTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.9	Unsigned32	read-write	This object handles Set Threshold for Stddev Alarm. 50 = Default value (5). - To calculate threshold use the following formula: SetTh/10. Default value: 50 (dB/10) Near end access: read-write. Far end access: no access.
INT xfRFStddevTrigger	1.3.6.1.4.1.193.81.3.4.3.1.9.1.24	INTEGER	read-only	This object manage IfCable Stddev Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
I32 xfRFStddevValue	1.3.6.1.4.1.193.81.3.4.3.1.9.1.19	Integer32	read-only	This object handles the value calculated on 24h for Stddev Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access.
U32 xfRFStepLimitHigh	1.3.6.1.4.1.193.81.3.4.3.1.2.1.5	Unsigned32	read-only	This object shows the highest allowed frequency step number.
U32 xfRFStepLimitHighRx	1.3.6.1.4.1.193.81.3.4.3.1.2.1.14	Unsigned32	read-only	This object shows the Rx highest allowed frequency step number.
U32 xfRFStepLimitLow	1.3.6.1.4.1.193.81.3.4.3.1.2.1.4	Unsigned32	read-only	This object shows the lowest allowed frequency step number.
U32 xfRFStepLimitLowRx	1.3.6.1.4.1.193.81.3.4.3.1.2.1.13	Unsigned32	read-only	This object shows the Rx lowest allowed frequency step number.
U32 xfRFStepSize	1.3.6.1.4.1.193.81.3.4.3.1.2.1.3	Unsigned32	read-only	This object shows the frequency step size in KHz.
U32 xfRFStepSizeRx	1.3.6.1.4.1.193.81.3.4.3.1.2.1.12	Unsigned32	read-only	This object shows the Rx frequency step size in KHz.
INT xfRfTaps	1.3.6.1.4.1.193.81.3.4.3.1.8.1.34	INTEGER	read-write	This object allows setting the Traffic Aware Power Saving. Default: disabled(3)
INT xfRFTxAdminStatus	1.3.6.1.4.1.193.81.3.4.3.1.2.1.8	INTEGER	read-write	This object sets the desired status of the transmitter. Value other(1) not settable. Especially for far end: txOff(2), requests far end transmitter to be turned off. txOn(3), requests far end transmitter to be turned on. Default value: txOff(2) - near end. other(1) - far end.
RFT xfRFTxOperStatus	1.3.6.1.4.1.193.81.3.4.3.1.2.1.7	RFTxOperStatus	read-only	This object shows the operational status of the transmitter.
INT xfSdcActualPath	1.3.6.1.4.1.193.81.3.4.3.1.10.1.10	INTEGER	read-only	SDC actual path (current value).
INT xfSdcAdminStatus	1.3.6.1.4.1.193.81.3.4.3.1.10.1.2	INTEGER	read-write	SDC Admin Status.
INT xfSdcCapability	1.3.6.1.4.1.193.81.3.4.3.1.10.1.1	INTEGER	read-only	SDC capability, including both MMU and ODU.
INT xfSdcDadeControl	1.3.6.1.4.1.193.81.3.4.3.1.10.1.4	INTEGER	read-write	SDC DADE procedure control.
I32 xfSdcDadeDelay	1.3.6.1.4.1.193.81.3.4.3.1.10.1.11	Integer32	read-only	DADE delay in nsec.
INT xfSdcDadeStatus	1.3.6.1.4.1.193.81.3.4.3.1.10.1.5	INTEGER	read-only	SDC DADE procedure status.
xfSdcEntry	1.3.6.1.4.1.193.81.3.4.3.1.10.1		not-accessible	An entry in the xfSdcTable.
I32 xfSdcGain	1.3.6.1.4.1.193.81.3.4.3.1.10.1.9	Integer32	read-only	SDC gain in dB/10. Domain: [0.0 .. 3.0 dB].
STR xfSdcOduDateTimeCalibration	1.3.6.1.4.1.193.81.3.4.3.1.10.1.7	DisplayString	read-only	Date and time of the SDC DADE calibration for the ODU with serial number in xfSdcOduSerialNumber. Format: [YYYY]-[MM]-[DD]T[hh]:[mm]:[ss] (ISO 8601).
STR xfSdcOduSerialNumber	1.3.6.1.4.1.193.81.3.4.3.1.10.1.8	DisplayString	read-only	Serial number of the ODU the current value of xfSdcOduDateTimeCalibration is referred to.
INT xfSdcOperStatus	1.3.6.1.4.1.193.81.3.4.3.1.10.1.3	INTEGER	read-only	SDC Oper Status.
INT xfSdcPath	1.3.6.1.4.1.193.81.3.4.3.1.10.1.6	INTEGER	read-write	SDC selected path (desired value).
xfSdcTable	1.3.6.1.4.1.193.81.3.4.3.1.10		not-accessible	Table for SDC capabilities, setting and status.

OID symbolic	OID numeric	Type	Access	Description
xfRadioLinkPtpRadioMIB	1.3.6.1.4.1.193.81.3.4.3			This MIB defines objects for point-to-point Radio Link RAUs.
xfRadioLinkPtpRadioObjects	1.3.6.1.4.1.193.81.3.4.3.1
xfRAUTable	1.3.6.1.4.1.193.81.3.4.3.1.1		not-accessible	Table for Radiolink point-to-point radios managed objects. Table indexed with entPhysicalIndex.
xfRAUEntry	1.3.6.1.4.1.193.81.3.4.3.1.1.1		not-accessible	An entry in xfRadioTable.
BIT xfRAUAlarmStatus	1.3.6.1.4.1.193.81.3.4.3.1.1.1.1	Bits	read-only	This object shows the alarm status of the radio unit. atpcCability - The terminal is configured for ATPC, but the radio does not support ATPC. This alarm is activated only if ATPC is turned on (any direction). sdcHwErrorMain - Received RF input signal level for Main path (of SDC TRX) has dropped below the threshold for the receiver. sdcHwErrorDiv - Received RF input signal level for Diversity path (of SDC TRX) has dropped below the threshold for the receiver. sdcDadeCalMismatch - A TRX is connected and its Serial Number doesn't match with the serial number stored into MO xfTRXSdcSerialNumber. insufficientResourceRauXpic - Connected RAU is missing capabilities for XPIC. companionRauMismatch - Connected RAU does not match with the companion one, either in 1+1 RLP or XPIC.
RAU xfRAURfLoopAvailable	1.3.6.1.4.1.193.81.3.4.3.1.1.1.2	RAURfLoopAvailable	read-only	This object inidicates if RF loop is available in radio unit.
RAU xfRAUAtpcCapability	1.3.6.1.4.1.193.81.3.4.3.1.1.1.3	RAUAtpcCapability	read-only	This object indicates if the radio unit supports ATPC or not.
INT xfRAULocalCtrlCapability	1.3.6.1.4.1.193.81.3.4.3.1.1.1.4	INTEGER	read-only	This object indicates if the radio unit supports local transmit power control or not.
RAU xfRAUModCapability	1.3.6.1.4.1.193.81.3.4.3.1.1.1.5	RAUModCapability	read-only	This object shows the modulation methods supported by the radio unit.
U32 xfRAUFrequencyband	1.3.6.1.4.1.193.81.3.4.3.1.1.1.6	Unsigned32	read-only	This object shows the frequency band for the radio unit.
U32 xfRAUSubBand	1.3.6.1.4.1.193.81.3.4.3.1.1.1.7	Unsigned32	read-write	This object shows the sub band (Index) for the radio unit.
I32 xfRAUTemperature	1.3.6.1.4.1.193.81.3.4.3.1.1.1.8	Integer32	read-only	This object shows the temperature, in degree Celsius, inside the radio unit.
INT xfRAUProtectionPath	1.3.6.1.4.1.193.81.3.4.3.1.1.1.9	INTEGER	read-only	This object indicates what radio path the radio belongs to.
INT xfRAURxCapability	1.3.6.1.4.1.193.81.3.4.3.1.1.1.10	INTEGER	read-only	This object indicates if the radio unit support RX configuration.
OCT xfRAUNotes	1.3.6.1.4.1.193.81.3.4.3.1.1.1.11	OCTET STRING	read-write	You can add information in this description field, for example polarization, antenna type or logging a site visit.
INT xfRauAtpcVersion	1.3.6.1.4.1.193.81.3.4.3.1.1.1.12	INTEGER	read-only	This object represents the RAU ATPC version.
BOO xfRauBoosterCapability	1.3.6.1.4.1.193.81.3.4.3.1.1.1.13	BoosterCapability	read-only	This object represents the Booster capability for a link.
I32 xfRauBoosterSelectedIndex	1.3.6.1.4.1.193.81.3.4.3.1.1.1.14	Integer32	read-write	This object represents the Booster selected index for a link.
xfRFIFTable	1.3.6.1.4.1.193.81.3.4.3.1.2		not-accessible	Table for Radiolink point-to-point radios RF IF managed objects. Table indexed with ifIndex.
xfRFIFEntry	1.3.6.1.4.1.193.81.3.4.3.1.2.1		not-accessible	An entry in the xfRFIFTable.
U32 xfRFBaseTxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.2.1.1	Unsigned32	read-only	This object shows the Tx frequency in KHz when frequency step number is 0.
U32 xfRFBaseRxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.2.1.2	Unsigned32	read-only	This object shows the Rx frequency in KHz when frequency. step number is 0
U32 xfRFStepSize	1.3.6.1.4.1.193.81.3.4.3.1.2.1.3	Unsigned32	read-only	This object shows the frequency step size in KHz.
U32 xfRFStepLimitLow	1.3.6.1.4.1.193.81.3.4.3.1.2.1.4	Unsigned32	read-only	This object shows the lowest allowed frequency step number.
U32 xfRFStepLimitHigh	1.3.6.1.4.1.193.81.3.4.3.1.2.1.5	Unsigned32	read-only	This object shows the highest allowed frequency step number.
U32 xfRFCurrentStepNumber	1.3.6.1.4.1.193.81.3.4.3.1.2.1.6	Unsigned32	read-write	This object sets/shows the frequency step number. 0 = frequency not yet defined. For Classic RAUs, TX and RX frequencies can not be set individually. The span between them is always fixed and depends on different frequency and sub band. - To calculate step number for TX and RX, use the following formulas: New step number = (TX frequency - XfRAUBaseTxFrequency) / XfRAUStepSize New step number = (RX frequency - xfRAUBaseRxFrequency) / XfRAUStepSize - To calculate TX and RX frequencies, use the following formulas: TX frequency = XfRAUBaseTxFrequency + XfRAUCurrentStepNumber * XfRAUStepSize RX frequency = XfRAUBaseRxFrequency + XfRAUCurrentStepNumber * XfRAUStepSize For Agile RAUs, the TX and RX frequencies can be set individually. Above formulas are only valid for TX frequency. For RX frequency, xfRFCurrentStepNumberRx must be used. Default value: 0
RFT xfRFTxOperStatus	1.3.6.1.4.1.193.81.3.4.3.1.2.1.7	RFTxOperStatus	read-only	This object shows the operational status of the transmitter.
INT xfRFTxAdminStatus	1.3.6.1.4.1.193.81.3.4.3.1.2.1.8	INTEGER	read-write	This object sets the desired status of the transmitter. Value other(1) not settable. Especially for far end: txOff(2), requests far end transmitter to be turned off. txOn(3), requests far end transmitter to be turned on. Default value: txOff(2) - near end. other(1) - far end.
INT xfRFLoopEnable	1.3.6.1.4.1.193.81.3.4.3.1.2.1.9	INTEGER	read-write	This object manage RF loop. Default value: disable(3). Near end access: read-write. Far end access: no access.
BIT xfRFAlarms	1.3.6.1.4.1.193.81.3.4.3.1.2.1.10	Bits	read-only	This TC enumerates the alarms for RF interface. txFrequency - Transmitter frequency synthesizer loop is unlocked. rxFrequency - Receiver frequency synthesizer loop is unlocked. rfOutputLevel - Major degradation of transmitter output power is detected. rxAfc - The frequency of the received signal is outside the range of the Automatic Frequency Control in the RAU receiver. rfInputLevel - Receiver RF input signal level has dropped below the threshold for the receiver. rfInputThreshold - The RF input level has dropped below the xfRFInputAlarmThreshold. rfOutputLevelATPC - The transmitter output power has been continuously at 'Patpc,max' for too long. This can occur due to several reasons: * The operator has set 'Patpc,max' too low. * The hop attenuation has increased (steady-state). * The transmitter PA is v. * The LNA in Rx is deteriorating.
BIT xfRFStatus	1.3.6.1.4.1.193.81.3.4.3.1.2.1.11	Bits	read-only	This object shows the RAU status. rfLoop - Warns if RF-loop is enabled on RAU txOff - Warns if TX is manually set to off
U32 xfRFStepSizeRx	1.3.6.1.4.1.193.81.3.4.3.1.2.1.12	Unsigned32	read-only	This object shows the Rx frequency step size in KHz.
U32 xfRFStepLimitLowRx	1.3.6.1.4.1.193.81.3.4.3.1.2.1.13	Unsigned32	read-only	This object shows the Rx lowest allowed frequency step number.
U32 xfRFStepLimitHighRx	1.3.6.1.4.1.193.81.3.4.3.1.2.1.14	Unsigned32	read-only	This object shows the Rx highest allowed frequency step number.
U32 xfRFCurrentStepNumberRx	1.3.6.1.4.1.193.81.3.4.3.1.2.1.15	Unsigned32	read-write	This object sets/shows the RX frequency step number for Agile RAUs. 0 = frequency not yet defined. - To calculate step number for RX, use the following formula: New step number Rx = (RX frequency - xfRAUBaseRxFrequency) / XfRAUStepSizeRx - To calculate RX frequency, use the following formula: RX frequency = XfRAUBaseRxFrequency + XfRAUCurrentStepNumberRx * XfRAUStepSizeRx Default value: 0
INT xfRFDuplexType	1.3.6.1.4.1.193.81.3.4.3.1.2.1.16	INTEGER	read-only	This object tells the duplex frequency mode for the RAU: - fixed: Tx frequency only can be set by operator, Rx frequency is automatically set on the basis of (fixed) RAU duplex frequency - variable: duplex frequency can be configured by operator
INT xfRFDuplexConfig	1.3.6.1.4.1.193.81.3.4.3.1.2.1.17	INTEGER	read-write	This object enables setting of duplex frequency for the RAU. It is always disabled(3) and can not be overwritten if xfRFDuplexType = fixed(2).
I32 xfRFDuplexDistance	1.3.6.1.4.1.193.81.3.4.3.1.2.1.18	Integer32	read-write	This object is aimed to select the duplex distance for the RAU. It can only be set if xfRFDuplexConfig = enabled(2), so that: xfRFDuplexDistance = Tx Frequency - Rx Frequency Otherwise, it is automatically filled on the basis of Tx and Rx frequency settings, and can not be overwritten.
xfRFPowerTable	1.3.6.1.4.1.193.81.3.4.3.1.3		not-accessible	Table for Radiolink point-to-point radios managed objects. Table indexed with ifIndex.
xfRFPowerEntry	1.3.6.1.4.1.193.81.3.4.3.1.3.1		not-accessible	An entry in the xfRFPowerTable.
I32 xfRFRtpcMinOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.2	Integer32	read-only	This object shows the minimum output power in dBm including attenuator. Value -100 indicate that RAU Tx on is not possible due to power supply limitations.
I32 xfRFRtpcMaxOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.3	Integer32	read-only	This object shows the maximum output power in dBm including attenuator. Value -100 indicate that RAU Tx on is not possible due to power supply limitations.
I32 xfRFRtpcSelectedOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.4	Integer32	read-write	This object set/shows the selected output power in dBm including attenuator. Value 254 indicates that the selected power is set to maximum. Default value: 254
I32 xfRFAtpcMinOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.5	Integer32	read-only	This object shows the minimum output power in dBm in ATPC. mode for radio contained in the radio terminal.
I32 xfRFAtpcMaxOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.6	Integer32	read-write	This object sets/shows the ATPC maximum output power in dBm for radio contained in the radio terminal. Value 254 indicates that the power is set to maximum. Default value: 254.
I32 xfRFAtpcMinInputPowerFar	1.3.6.1.4.1.193.81.3.4.3.1.3.1.7	Integer32	read-only	This object shows the ATPC minimum input target power level for far end radio.
I32 xfRFAtpcSelectedInputPowerFar	1.3.6.1.4.1.193.81.3.4.3.1.3.1.8	Integer32	read-write	This object sets/shows the ATPC selected input target level for far end radio. Default value: -30.
I32 xfRFAttenuator	1.3.6.1.4.1.193.81.3.4.3.1.3.1.9	Integer32	read-write	This object sets/shows the value in dBm for fixed attenuator mounted in antenna. Default value: 0.
I32 xfRFOutputPower8QAM	1.3.6.1.4.1.193.81.3.4.3.1.3.1.18	Integer32	read-only	Output power for 8QAM.
INT xfRFMaxOutputPowerNotPossible	1.3.6.1.4.1.193.81.3.4.3.1.3.1.30	INTEGER	read-only	unknown(0) isPossible(1) Max output power is possible due to power supply limitations isNotPossible(2) Max output power is not possible due to power supply limitations
I32 xfRFMaxMSELast7Days	1.3.6.1.4.1.193.81.3.4.3.1.3.1.38	Integer32	read-only	Indicate Max MSE level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.
I32 xfRFMinMSELast7Days	1.3.6.1.4.1.193.81.3.4.3.1.3.1.39	Integer32	read-only	Indicate Min MSE level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.
I32 xfRFMaxXPILast7Days	1.3.6.1.4.1.193.81.3.4.3.1.3.1.40	Integer32	read-only	Indicate Max Cross-Polar Interference (XPI) level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.
I32 xfRFMinXPILast7Days	1.3.6.1.4.1.193.81.3.4.3.1.3.1.41	Integer32	read-only	Indicate Min Cross-Polar Interference (XPI) level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.
I32 xfRFBoosterGain	1.3.6.1.4.1.193.81.3.4.3.1.3.1.43	Integer32	read-only	Value of the Gain of the Booster
I32 xfRFBoosterMaxInputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.44	Integer32	read-only	Value of the Max Input Power admitted towards the Booster
BOO xfRFBoosterCapability	1.3.6.1.4.1.193.81.3.4.3.1.3.1.45	BoosterCapability	read-only	Value of Booster capability according to the system
STR xfRFBoosterProductNumber	1.3.6.1.4.1.193.81.3.4.3.1.3.1.46	DisplayString	read-write	Product Number of the Booster connected to the specific RF IF
STR xfRFBoosterHWRevision	1.3.6.1.4.1.193.81.3.4.3.1.3.1.47	DisplayString	read-write	HW Revision of the Booster connected to the specific RF IF
xfRAUCapabilityTable	1.3.6.1.4.1.193.81.3.4.3.1.4		not-accessible	Table for RAU capability information. Table indexed with entPhysicalIndex and xfTermRowIndex.
xfRAUCapabilityEntry	1.3.6.1.4.1.193.81.3.4.3.1.4.1		not-accessible	An entry in xfRAUCapabilityTable.
RAU xfRAUChannelSpacing	1.3.6.1.4.1.193.81.3.4.3.1.4.1.1	RAUChannelSpacingCapability	read-only	Channel spacing. ETSI: 3.5, 7, 14, 28, 40, 56 MHz ANSI: 10, 20, 30, 40, 50 MHz
RAU xfRAUChannelModulation	1.3.6.1.4.1.193.81.3.4.3.1.4.1.2	RAUModulation	read-only	This object shows the modulation. Values: cqpsk(2) CQPSK qam16(3) 16-QAM qam128(4) 128-QAM qam32(5) 32-QAM qam64(6) 64-QAM qam4(7) 4-QAM qam8(8) 8-QAM qam256(9) 256-QAM qam512(10) 512-QAM qam1024(11) 1024-QAM
RAU xfRAUSpectrumEfficiencyClass	1.3.6.1.4.1.193.81.3.4.3.1.4.1.3	RauSec	read-only	Spectrum Efficiency Class: other(1), unknown sec2(2), Spectrum eff. Class 2 sec3(3), Spectrum eff. Class 3 sec4L(4), Spectrum eff. Class 4L sec4H(5), Specturm eff. Class 4H sec5A(6), Spectrum eff. Class 5A sec5B(7), Spectrum eff. Class 5B sec6A(8), Spectrum eff. Class 6A sec6B(9) Spectrum eff. Class 6B
INT xfRAUCarrierMode	1.3.6.1.4.1.193.81.3.4.3.1.4.1.4	INTEGER	read-only	Radio carrier mode.
xfRAUSubBandTable	1.3.6.1.4.1.193.81.3.4.3.1.5		not-accessible	Table for RAU Sub-Band index capability. Table indexed with entPhysicalIndex and xfRAUSubBandIndex.
xfRAUSubBandEntry	1.3.6.1.4.1.193.81.3.4.3.1.5.1		not-accessible	An entry in xfRAUSubBandTable.
U32 xfRAUSubBandIndex	1.3.6.1.4.1.193.81.3.4.3.1.5.1.1	Unsigned32	read-only	An index for the specific RAU Sub-Band available index range.
U32 xfRAUSubBandRange	1.3.6.1.4.1.193.81.3.4.3.1.5.1.2	Unsigned32	read-only	This object shows the RAU Sub-Band available index range [0..255].
xfRFSpectrumDiagTable	1.3.6.1.4.1.193.81.3.4.3.1.6		not-accessible	Table for RF Spectrum Diagnostics control and status
xfRFSpectrumDiagEntry	1.3.6.1.4.1.193.81.3.4.3.1.6.1		not-accessible	An entry in xfRFSpectrumDiagTable
INT xfRFSpectrumDiagAdminStatus	1.3.6.1.4.1.193.81.3.4.3.1.6.1.1	INTEGER	read-write	RF Spectrum Diagnostics Admin Status
INT xfRFSpectrumDiagOperStatus	1.3.6.1.4.1.193.81.3.4.3.1.6.1.2	INTEGER	read-only	RF Spectrum Diagnostics Oper Status
U32 xfRFSpectrumDiagChannelScanEstTime	1.3.6.1.4.1.193.81.3.4.3.1.6.1.3	Unsigned32	read-only	Estimated time in seconds for scanning one Channel Spacing at current RX frequency
U32 xfRFSpectrumDiagSubBandScanEstTime	1.3.6.1.4.1.193.81.3.4.3.1.6.1.4	Unsigned32	read-only	Estimated time in seconds for scanning full Sub Band of connected RAU
STR xfRFSpectrumDiagScanDate	1.3.6.1.4.1.193.81.3.4.3.1.6.1.5	DisplayString	read-only	Date and time when scan (channel or sub-band) is completed, format: [YYYY]-[MM]-[DD]T[hh]:[mm]:[ss]
U32 xfRFSpectrumDiagChannelSpacing	1.3.6.1.4.1.193.81.3.4.3.1.6.1.6	Unsigned32	read-only	Channel width measured by Spectrum Diagnostics
U32 xfRFSpectrumDiagCurrRxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.6.1.7	Unsigned32	read-only	Current value of Rx frequency
U32 xfRFSpectrumDiagMinRxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.6.1.8	Unsigned32	read-only	Minimum sub-band Rx frequency (RAU lower edge)
U32 xfRFSpectrumDiagMaxRxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.6.1.9	Unsigned32	read-only	Maximum sub-band Rx frequency (RAU upper edge)
U32 xfRFSpectrumDiagIdxCompanion1	1.3.6.1.4.1.193.81.3.4.3.1.6.1.10	Unsigned32	read-only	RF IF index for 1st companion carrier (0 if no companion)
U32 xfRFSpectrumDiagIdxCompanion2	1.3.6.1.4.1.193.81.3.4.3.1.6.1.11	Unsigned32	read-only	RF IF index for 2nd companion carrier (0 if no companion)
U32 xfRFSpectrumDiagIdxCompanion3	1.3.6.1.4.1.193.81.3.4.3.1.6.1.12	Unsigned32	read-only	RF IF index for 3rd companion carrier (0 if no companion)
U32 xfRFSpectrumDiagProgress	1.3.6.1.4.1.193.81.3.4.3.1.6.1.13	Unsigned32	read-only	Completed percentage of Spectrum Diagnostics scan
xfRFSpectrumDiagResultTable	1.3.6.1.4.1.193.81.3.4.3.1.7		not-accessible	Table of Spectrum Diagnostics scan results
xfRFSpectrumDiagResultEntry	1.3.6.1.4.1.193.81.3.4.3.1.7.1		not-accessible	An entry in xfRFSpectrumDiagResultTable
U32 xfRFSpectrumDiagResultIndex	1.3.6.1.4.1.193.81.3.4.3.1.7.1.1	Unsigned32	read-only	Spectrum Diagnostics Scan Result Index
U32 xfRFSpectrumDiagResultRxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.7.1.2	Unsigned32	read-only	Spectrum Diagnostics Scan Result Rx frequency in kHz
I32 xfRFSpectrumDiagResultRxPower	1.3.6.1.4.1.193.81.3.4.3.1.7.1.3	Integer32	read-only	Spectrum Diagnostics Scan Result Rx Power value/10 dBm Domain: [-99.9 .. -20.0 dBm]
xfRfIfPowerTable	1.3.6.1.4.1.193.81.3.4.3.1.8		not-accessible	Table for Radio Link RAU managed objects. Table indexed with ifIndex.
xfRfIfPowerEntry	1.3.6.1.4.1.193.81.3.4.3.1.8.1		not-accessible	An entry in the xfRfIfPowerTable.
RFO xfRfSelectedMinOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.1	RfOutputPower	read-write	Minimum output power in dBm (selected by operator). Default value: 10 dBm.
RFO xfRfSelectedMaxOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.2	RfOutputPower	read-write	Maximum output power in dBm (selected by operator). Default value: 10 dBm.
RFO xfRFCurrentOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.3	RfOutputPower	read-only	Current output power in dBm. 255 indicates invalid value.
RFO xfRfMinOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.4	RfOutputPower	read-only	Minimum output power in dBm (provided by RAU). 255 indicates invalid value.
RFO xfRfMaxOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.5	RfOutputPower	read-only	Maximum output power in dBm (provided by RAU). 255 indicates invalid value.
I32 xfRfAtpcTargetInputPowerFE	1.3.6.1.4.1.193.81.3.4.3.1.8.1.6	Integer32	read-write	ATPC target input power on Far End side. Default value: -30.
RFI xfRFCurrentInputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.7	RfInputPower	read-only	RF input level. Value is in 1/10 dBm. Domain: [-20.0 .. -99.9 dBm].
RFI xfRFMaxInputPowerLast7Days	1.3.6.1.4.1.193.81.3.4.3.1.8.1.8	RfInputPower	read-only	Maximum RF input level in the last 7 days. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.
RFI xfRFMinInputPowerLast7Days	1.3.6.1.4.1.193.81.3.4.3.1.8.1.9	RfInputPower	read-only	Minimum RF input level in the last 7 days. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.
RFI xfRFMaxInputPowerSinceReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.10	RfInputPower	read-only	Maximum RF input level since reset. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.
RFI xfRFMinInputPowerSinceReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.11	RfInputPower	read-only	Minimum RF input level since reset. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.
INT xfRFInputPowerReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.12	INTEGER	read-write	This object resets the registers for: - RF input power levels - input levels (i.e. RF power, MSE and XPI) in the next 7 days period of time.
I32 xfRFInputAlarmThreshold	1.3.6.1.4.1.193.81.3.4.3.1.8.1.13	Integer32	read-write	RF input level threshold. Default value: -93.
RFO xfRFOutputPower4QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.14	RfOutputPower	read-only	Output power for 4QAM. 255 indicates invalid value.
RFO xfRFOutputPower16QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.15	RfOutputPower	read-only	Output power for 16QAM. 255 indicates invalid value.
RFO xfRFOutputPower32QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.16	RfOutputPower	read-only	Output power for 32QAM. 255 indicates invalid value.
RFO xfRFOutputPower64QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.17	RfOutputPower	read-only	Output power for 64QAM. 255 indicates invalid value.
RFO xfRFOutputPower128QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.18	RfOutputPower	read-only	Output power for 128QAM. 255 indicates invalid value.
RFO xfRFOutputPower256QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.19	RfOutputPower	read-only	Output power for 256QAM. 255 indicates invalid value.
RFO xfRFOutputPower512QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.20	RfOutputPower	read-only	Output power for 512QAM. 255 indicates invalid value.
RFO xfRFOutputPower1024QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.21	RfOutputPower	read-only	Output power for 1024QAM. 255 indicates invalid value.
RFO xfRfOutputPower2048QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.22	RfOutputPower	read-only	Output power for 2048QAM. 255 indicates invalid value.
RFO xfRfOutputPower4096QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.23	RfOutputPower	read-only	Output power for 4096QAM. 255 indicates invalid value.
RFO xfRFMaxOutputPowerNotLimited	1.3.6.1.4.1.193.81.3.4.3.1.8.1.24	RfOutputPower	read-only	Max output power in dBm that the RAU can give if it is not power supply limited. 255 indicates invalid value.
INT xfRfMaxOutputPowerPossible	1.3.6.1.4.1.193.81.3.4.3.1.8.1.25	INTEGER	read-only	possible(2): max output power is possible. notPossible(3): max output power is not possible, due to power supply limitations.
I32 xfRFMeanInputPower1m	1.3.6.1.4.1.193.81.3.4.3.1.8.1.26	Integer32	read-only	This object shows RF input mean level for last minute. RF input level = value/10 dBm. Domain: [-99.9 ... -20.0 dBm] 0 (zero) indicates invalid value.
I32 xfRFMaxOutputPowerLast7Days	1.3.6.1.4.1.193.81.3.4.3.1.8.1.27	Integer32	read-only	This object shows maximum RF output level last 7 days. RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.
I32 xfRFMinOutputPowerLast7Days	1.3.6.1.4.1.193.81.3.4.3.1.8.1.28	Integer32	read-only	This object shows minimum RF output level last 7 days. RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.
I32 xfRFMaxOutputPowerSinceReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.29	Integer32	read-only	This object shows maximum RF output level since reset RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.
I32 xfRFMinOutputPowerSinceReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.30	Integer32	read-only	This object shows minimum RF output level since reset RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.
INT xfRFOutputPowerReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.31	INTEGER	read-write	This object reset the registers for the RF output level and All Time High level this seven days period and counters for the next seven days period of time.
INT xfRfAvailableOutputPowerType	1.3.6.1.4.1.193.81.3.4.3.1.8.1.32	INTEGER	read-only	This object reports the output power capability of the RAU: - standardPower - highPower
INT xfRfSelectedOutputPowerType	1.3.6.1.4.1.193.81.3.4.3.1.8.1.33	INTEGER	read-write	This object allows setting the output power type: - standardPower - highPower default: standardPower(2) When the type is set to highPower(3) a HP license key is required. If the license key is not present the capacity is limited to Basic Capacity. The output power can be configured as 'normal' without any impact from the HP license key (present or not). When the mode is standardPower(2) the availableMaxOutputPower is limited to 'max power' - 4 dB per modulation.
INT xfRfTaps	1.3.6.1.4.1.193.81.3.4.3.1.8.1.34	INTEGER	read-write	This object allows setting the Traffic Aware Power Saving. Default: disabled(3)
RFI xfRFCurrentInputPowerSdcMain	1.3.6.1.4.1.193.81.3.4.3.1.8.1.35	RfInputPower	read-only	This object shows RF input level for SDC Main path = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. 0 (zero) indicates invalid value (e.g. SDC not available).
RFI xfRFCurrentInputPowerSdcDiv	1.3.6.1.4.1.193.81.3.4.3.1.8.1.36	RfInputPower	read-only	This object shows RF input level for SDC Diversity path = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. 0 (zero) indicates invalid value (e.g. SDC not available).
RFO xfRfOutputPower8192QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.37	RfOutputPower	read-only	Output power for 8192QAM. 255 indicates invalid value.
RFO xfRfOutputPower16384QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.38	RfOutputPower	read-only	Output power for 16384QAM. 255 indicates invalid value.
RFO xfRFAtpcFallbackOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.39	RfOutputPower	read-write	This object sets output power (in dBm) in ATPCFallback mode, for radio contained in the Carrier Termination. 255 indicates invalid value.
ATP xfRFAtpcFallbackEnable	1.3.6.1.4.1.193.81.3.4.3.1.8.1.40	ATPCFallbackEnable	read-write	Enable/disable ATPCFallback.
I32 xfRFAtpcFallbackTimer	1.3.6.1.4.1.193.81.3.4.3.1.8.1.41	Integer32	read-write	This object specifies how long the output power can be at (ATPC, MAX) before ATPC fallback is triggered. Default value: ETSI 15 min, ANSI 5 min.
xfRFIFCableMonitoringTable	1.3.6.1.4.1.193.81.3.4.3.1.9		not-accessible	Table for Radiolink point-to-point radios RF IF Cable Monitoring managed objects. Table indexed with ifIndex.
xfRFIFCableMonitoringEntry	1.3.6.1.4.1.193.81.3.4.3.1.9.1		not-accessible	An entry in the xfRFIFCableMonitoringTable.
INT xfRFIFCMStatus	1.3.6.1.4.1.193.81.3.4.3.1.9.1.1	INTEGER	read-write	This object manage IfCable Monitoring Status. Default value: disable(2). Near end access: read-write. Far end access: no access.
INT xfRFOutlierAgc	1.3.6.1.4.1.193.81.3.4.3.1.9.1.2	INTEGER	read-write	This object manage IfCable Outlier Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
U32 xfRFOutlierSetTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.3	Unsigned32	read-write	This object handles Set Threshold for Outlier Alarm. 3 = Default value (0.3). - To calculate threshold use the following formula: SetTh/10. Default value: 3 Near end access: read-write. Far end access: no access.
U32 xfRFOutlierCeaseTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.4	Unsigned32	read-write	This object handles Cease Threshold for Outlier Alarm. 2 = Default value (0.2). - To calculate threshold use the following formula: SetTh/10. Default value: 2 Near end access: read-write. Far end access: no access.
INT xfRFRangeAgc	1.3.6.1.4.1.193.81.3.4.3.1.9.1.5	INTEGER	read-write	This object manage IfCable Range Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
U32 xfRFRangeSetTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.6	Unsigned32	read-write	This object handles Set Threshold for Range Alarm. 30 = Default value (3). - To calculate threshold use the following formula: SetTh/10. Default value: 30 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFRangeCeaseTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.7	Unsigned32	read-write	This object handles Cease Threshold for Range Alarm. 20 = Default value (2). - To calculate threshold use the following formula: SetTh/10. Default value: 20 (dB/10) Near end access: read-write. Far end access: no access.
INT xfRFStddevAgc	1.3.6.1.4.1.193.81.3.4.3.1.9.1.8	INTEGER	read-write	This object manage IfCable Stddev Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
U32 xfRFStddevSetTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.9	Unsigned32	read-write	This object handles Set Threshold for Stddev Alarm. 50 = Default value (5). - To calculate threshold use the following formula: SetTh/10. Default value: 50 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFStddevCeaseTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.10	Unsigned32	read-write	This object handles Cease Threshold for Stddev Alarm. 20 = Default value (2). - To calculate threshold use the following formula: SetTh/10. Default value: 20 (dB/10) Near end access: read-write. Far end access: no access.
INT xfRFDegradationAgc	1.3.6.1.4.1.193.81.3.4.3.1.9.1.11	INTEGER	read-write	This object manage IfCable Degradation Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
U32 xfRFDegradationSetTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.12	Unsigned32	read-write	This object handles Set Threshold for Degradation Alarm. 2 = Default value (0.2). - To calculate threshold use the following formula: SetTh/10. Default value: 2 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFDegradationCeaseTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.13	Unsigned32	read-write	This object handles Cease Threshold for Degradation Alarm. 1 = Default value (0.1). - To calculate threshold use the following formula: SetTh/10. Default value: 1 (dB/10) Near end access: read-write. Far end access: no access.
INT xfRFMarginAgc	1.3.6.1.4.1.193.81.3.4.3.1.9.1.14	INTEGER	read-write	This object manage IfCable Margin Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
U32 xfRFMarginSetTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.15	Unsigned32	read-write	This object handles Set Threshold for Margin Alarm. 30 = Default value (3). - To calculate threshold use the following formula: SetTh/10. Default value: 30 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFMarginCeaseTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.16	Unsigned32	read-write	This object handles Cease Threshold for Margin Alarm. 60 = Default value (6). - To calculate threshold use the following formula: SetTh/10. Default value: 60 (dB/10) Near end access: read-write. Far end access: no access.
I32 xfRFOutlierValue	1.3.6.1.4.1.193.81.3.4.3.1.9.1.17	Integer32	read-only	This object handles the value calculated on 24h for Outlier Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 Near end access: read-write. Far end access: no access.
I32 xfRFRangeValue	1.3.6.1.4.1.193.81.3.4.3.1.9.1.18	Integer32	read-only	This object handles the value calculated on 24h for Range Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access.
I32 xfRFStddevValue	1.3.6.1.4.1.193.81.3.4.3.1.9.1.19	Integer32	read-only	This object handles the value calculated on 24h for Stddev Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access.
I32 xfRFDegradationValue	1.3.6.1.4.1.193.81.3.4.3.1.9.1.20	Integer32	read-only	This object handles the value calculated on 24h for Degradation Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access.
I32 xfRFMarginValue	1.3.6.1.4.1.193.81.3.4.3.1.9.1.21	Integer32	read-only	This object handles the value calculated on 24h for Margin Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access.
INT xfRFOutlierTrigger	1.3.6.1.4.1.193.81.3.4.3.1.9.1.22	INTEGER	read-only	This object manage IfCable Outlier Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
INT xfRFRangeTrigger	1.3.6.1.4.1.193.81.3.4.3.1.9.1.23	INTEGER	read-only	This object manage IfCable Range Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
INT xfRFStddevTrigger	1.3.6.1.4.1.193.81.3.4.3.1.9.1.24	INTEGER	read-only	This object manage IfCable Stddev Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
INT xfRFDegradationTrigger	1.3.6.1.4.1.193.81.3.4.3.1.9.1.25	INTEGER	read-only	This object manage IfCable Degradation Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
INT xfRFMarginTrigger	1.3.6.1.4.1.193.81.3.4.3.1.9.1.26	INTEGER	read-only	This object manage IfCable Margin Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
xfSdcTable	1.3.6.1.4.1.193.81.3.4.3.1.10		not-accessible	Table for SDC capabilities, setting and status.
xfSdcEntry	1.3.6.1.4.1.193.81.3.4.3.1.10.1		not-accessible	An entry in the xfSdcTable.
INT xfSdcCapability	1.3.6.1.4.1.193.81.3.4.3.1.10.1.1	INTEGER	read-only	SDC capability, including both MMU and ODU.
INT xfSdcAdminStatus	1.3.6.1.4.1.193.81.3.4.3.1.10.1.2	INTEGER	read-write	SDC Admin Status.
INT xfSdcOperStatus	1.3.6.1.4.1.193.81.3.4.3.1.10.1.3	INTEGER	read-only	SDC Oper Status.
INT xfSdcDadeControl	1.3.6.1.4.1.193.81.3.4.3.1.10.1.4	INTEGER	read-write	SDC DADE procedure control.
INT xfSdcDadeStatus	1.3.6.1.4.1.193.81.3.4.3.1.10.1.5	INTEGER	read-only	SDC DADE procedure status.
INT xfSdcPath	1.3.6.1.4.1.193.81.3.4.3.1.10.1.6	INTEGER	read-write	SDC selected path (desired value).
STR xfSdcOduDateTimeCalibration	1.3.6.1.4.1.193.81.3.4.3.1.10.1.7	DisplayString	read-only	Date and time of the SDC DADE calibration for the ODU with serial number in xfSdcOduSerialNumber. Format: [YYYY]-[MM]-[DD]T[hh]:[mm]:[ss] (ISO 8601).
STR xfSdcOduSerialNumber	1.3.6.1.4.1.193.81.3.4.3.1.10.1.8	DisplayString	read-only	Serial number of the ODU the current value of xfSdcOduDateTimeCalibration is referred to.
I32 xfSdcGain	1.3.6.1.4.1.193.81.3.4.3.1.10.1.9	Integer32	read-only	SDC gain in dB/10. Domain: [0.0 .. 3.0 dB].
INT xfSdcActualPath	1.3.6.1.4.1.193.81.3.4.3.1.10.1.10	INTEGER	read-only	SDC actual path (current value).
I32 xfSdcDadeDelay	1.3.6.1.4.1.193.81.3.4.3.1.10.1.11	Integer32	read-only	DADE delay in nsec.
xfRadioLinkPtpRadioConformance	1.3.6.1.4.1.193.81.3.4.3.2
xfRadioLinkPtpRadioCompliances	1.3.6.1.4.1.193.81.3.4.3.2.1
xfRADIOLINKPTPRADIOFullCompliance	1.3.6.1.4.1.193.81.3.4.3.2.1.1			The compliance statement for SNMP entities which implement everything.
xfRadioLinkPtpRadioGroups	1.3.6.1.4.1.193.81.3.4.3.2.2
xfRadioLinkPtpRadioCompleteGroup	1.3.6.1.4.1.193.81.3.4.3.2.2.1			A collection of all current objects in this MIB module.

ATPCFallbackEnable (1)
ATP xfRFAtpcFallbackEnable	1.3.6.1.4.1.193.81.3.4.3.1.8.1.40	ATPCFallbackEnable	read-write	Enable/disable ATPCFallback.
Bits (3)
BIT xfRAUAlarmStatus	1.3.6.1.4.1.193.81.3.4.3.1.1.1.1	Bits	read-only	This object shows the alarm status of the radio unit. atpcCability - The terminal is configured for ATPC, but the radio does not support ATPC. This alarm is activated only if ATPC is turned on (any direction). sdcHwErrorMain - Received RF input signal level for Main path (of SDC TRX) has dropped below the threshold for the receiver. sdcHwErrorDiv - Received RF input signal level for Diversity path (of SDC TRX) has dropped below the threshold for the receiver. sdcDadeCalMismatch - A TRX is connected and its Serial Number doesn't match with the serial number stored into MO xfTRXSdcSerialNumber. insufficientResourceRauXpic - Connected RAU is missing capabilities for XPIC. companionRauMismatch - Connected RAU does not match with the companion one, either in 1+1 RLP or XPIC.
BIT xfRFAlarms	1.3.6.1.4.1.193.81.3.4.3.1.2.1.10	Bits	read-only	This TC enumerates the alarms for RF interface. txFrequency - Transmitter frequency synthesizer loop is unlocked. rxFrequency - Receiver frequency synthesizer loop is unlocked. rfOutputLevel - Major degradation of transmitter output power is detected. rxAfc - The frequency of the received signal is outside the range of the Automatic Frequency Control in the RAU receiver. rfInputLevel - Receiver RF input signal level has dropped below the threshold for the receiver. rfInputThreshold - The RF input level has dropped below the xfRFInputAlarmThreshold. rfOutputLevelATPC - The transmitter output power has been continuously at 'Patpc,max' for too long. This can occur due to several reasons: * The operator has set 'Patpc,max' too low. * The hop attenuation has increased (steady-state). * The transmitter PA is v. * The LNA in Rx is deteriorating.
BIT xfRFStatus	1.3.6.1.4.1.193.81.3.4.3.1.2.1.11	Bits	read-only	This object shows the RAU status. rfLoop - Warns if RF-loop is enabled on RAU txOff - Warns if TX is manually set to off
BoosterCapability (2)
BOO xfRauBoosterCapability	1.3.6.1.4.1.193.81.3.4.3.1.1.1.13	BoosterCapability	read-only	This object represents the Booster capability for a link.
BOO xfRFBoosterCapability	1.3.6.1.4.1.193.81.3.4.3.1.3.1.45	BoosterCapability	read-only	Value of Booster capability according to the system
DisplayString (5)
STR xfRFBoosterHWRevision	1.3.6.1.4.1.193.81.3.4.3.1.3.1.47	DisplayString	read-write	HW Revision of the Booster connected to the specific RF IF
STR xfRFBoosterProductNumber	1.3.6.1.4.1.193.81.3.4.3.1.3.1.46	DisplayString	read-write	Product Number of the Booster connected to the specific RF IF
STR xfRFSpectrumDiagScanDate	1.3.6.1.4.1.193.81.3.4.3.1.6.1.5	DisplayString	read-only	Date and time when scan (channel or sub-band) is completed, format: [YYYY]-[MM]-[DD]T[hh]:[mm]:[ss]
STR xfSdcOduDateTimeCalibration	1.3.6.1.4.1.193.81.3.4.3.1.10.1.7	DisplayString	read-only	Date and time of the SDC DADE calibration for the ODU with serial number in xfSdcOduSerialNumber. Format: [YYYY]-[MM]-[DD]T[hh]:[mm]:[ss] (ISO 8601).
STR xfSdcOduSerialNumber	1.3.6.1.4.1.193.81.3.4.3.1.10.1.8	DisplayString	read-only	Serial number of the ODU the current value of xfSdcOduDateTimeCalibration is referred to.
INTEGER (36)
INT xfRauAtpcVersion	1.3.6.1.4.1.193.81.3.4.3.1.1.1.12	INTEGER	read-only	This object represents the RAU ATPC version.
INT xfRAUCarrierMode	1.3.6.1.4.1.193.81.3.4.3.1.4.1.4	INTEGER	read-only	Radio carrier mode.
INT xfRAULocalCtrlCapability	1.3.6.1.4.1.193.81.3.4.3.1.1.1.4	INTEGER	read-only	This object indicates if the radio unit supports local transmit power control or not.
INT xfRAUProtectionPath	1.3.6.1.4.1.193.81.3.4.3.1.1.1.9	INTEGER	read-only	This object indicates what radio path the radio belongs to.
INT xfRAURxCapability	1.3.6.1.4.1.193.81.3.4.3.1.1.1.10	INTEGER	read-only	This object indicates if the radio unit support RX configuration.
INT xfRfAvailableOutputPowerType	1.3.6.1.4.1.193.81.3.4.3.1.8.1.32	INTEGER	read-only	This object reports the output power capability of the RAU: - standardPower - highPower
INT xfRFDegradationAgc	1.3.6.1.4.1.193.81.3.4.3.1.9.1.11	INTEGER	read-write	This object manage IfCable Degradation Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
INT xfRFDegradationTrigger	1.3.6.1.4.1.193.81.3.4.3.1.9.1.25	INTEGER	read-only	This object manage IfCable Degradation Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
INT xfRFDuplexConfig	1.3.6.1.4.1.193.81.3.4.3.1.2.1.17	INTEGER	read-write	This object enables setting of duplex frequency for the RAU. It is always disabled(3) and can not be overwritten if xfRFDuplexType = fixed(2).
INT xfRFDuplexType	1.3.6.1.4.1.193.81.3.4.3.1.2.1.16	INTEGER	read-only	This object tells the duplex frequency mode for the RAU: - fixed: Tx frequency only can be set by operator, Rx frequency is automatically set on the basis of (fixed) RAU duplex frequency - variable: duplex frequency can be configured by operator
INT xfRFIFCMStatus	1.3.6.1.4.1.193.81.3.4.3.1.9.1.1	INTEGER	read-write	This object manage IfCable Monitoring Status. Default value: disable(2). Near end access: read-write. Far end access: no access.
INT xfRFInputPowerReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.12	INTEGER	read-write	This object resets the registers for: - RF input power levels - input levels (i.e. RF power, MSE and XPI) in the next 7 days period of time.
INT xfRFLoopEnable	1.3.6.1.4.1.193.81.3.4.3.1.2.1.9	INTEGER	read-write	This object manage RF loop. Default value: disable(3). Near end access: read-write. Far end access: no access.
INT xfRFMarginAgc	1.3.6.1.4.1.193.81.3.4.3.1.9.1.14	INTEGER	read-write	This object manage IfCable Margin Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
INT xfRFMarginTrigger	1.3.6.1.4.1.193.81.3.4.3.1.9.1.26	INTEGER	read-only	This object manage IfCable Margin Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
INT xfRFMaxOutputPowerNotPossible	1.3.6.1.4.1.193.81.3.4.3.1.3.1.30	INTEGER	read-only	unknown(0) isPossible(1) Max output power is possible due to power supply limitations isNotPossible(2) Max output power is not possible due to power supply limitations
INT xfRfMaxOutputPowerPossible	1.3.6.1.4.1.193.81.3.4.3.1.8.1.25	INTEGER	read-only	possible(2): max output power is possible. notPossible(3): max output power is not possible, due to power supply limitations.
INT xfRFOutlierAgc	1.3.6.1.4.1.193.81.3.4.3.1.9.1.2	INTEGER	read-write	This object manage IfCable Outlier Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
INT xfRFOutlierTrigger	1.3.6.1.4.1.193.81.3.4.3.1.9.1.22	INTEGER	read-only	This object manage IfCable Outlier Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
INT xfRFOutputPowerReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.31	INTEGER	read-write	This object reset the registers for the RF output level and All Time High level this seven days period and counters for the next seven days period of time.
INT xfRFRangeAgc	1.3.6.1.4.1.193.81.3.4.3.1.9.1.5	INTEGER	read-write	This object manage IfCable Range Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
INT xfRFRangeTrigger	1.3.6.1.4.1.193.81.3.4.3.1.9.1.23	INTEGER	read-only	This object manage IfCable Range Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
INT xfRfSelectedOutputPowerType	1.3.6.1.4.1.193.81.3.4.3.1.8.1.33	INTEGER	read-write	This object allows setting the output power type: - standardPower - highPower default: standardPower(2) When the type is set to highPower(3) a HP license key is required. If the license key is not present the capacity is limited to Basic Capacity. The output power can be configured as 'normal' without any impact from the HP license key (present or not). When the mode is standardPower(2) the availableMaxOutputPower is limited to 'max power' - 4 dB per modulation.
INT xfRFSpectrumDiagAdminStatus	1.3.6.1.4.1.193.81.3.4.3.1.6.1.1	INTEGER	read-write	RF Spectrum Diagnostics Admin Status
INT xfRFSpectrumDiagOperStatus	1.3.6.1.4.1.193.81.3.4.3.1.6.1.2	INTEGER	read-only	RF Spectrum Diagnostics Oper Status
INT xfRFStddevAgc	1.3.6.1.4.1.193.81.3.4.3.1.9.1.8	INTEGER	read-write	This object manage IfCable Stddev Alarm. Default value: disable(2). Near end access: read-write. Far end access: no access.
INT xfRFStddevTrigger	1.3.6.1.4.1.193.81.3.4.3.1.9.1.24	INTEGER	read-only	This object manage IfCable Stddev Trigger. Default value: noSetThreshold(2). Near end access: read-write. Far end access: no access.
INT xfRfTaps	1.3.6.1.4.1.193.81.3.4.3.1.8.1.34	INTEGER	read-write	This object allows setting the Traffic Aware Power Saving. Default: disabled(3)
INT xfRFTxAdminStatus	1.3.6.1.4.1.193.81.3.4.3.1.2.1.8	INTEGER	read-write	This object sets the desired status of the transmitter. Value other(1) not settable. Especially for far end: txOff(2), requests far end transmitter to be turned off. txOn(3), requests far end transmitter to be turned on. Default value: txOff(2) - near end. other(1) - far end.
INT xfSdcActualPath	1.3.6.1.4.1.193.81.3.4.3.1.10.1.10	INTEGER	read-only	SDC actual path (current value).
INT xfSdcAdminStatus	1.3.6.1.4.1.193.81.3.4.3.1.10.1.2	INTEGER	read-write	SDC Admin Status.
INT xfSdcCapability	1.3.6.1.4.1.193.81.3.4.3.1.10.1.1	INTEGER	read-only	SDC capability, including both MMU and ODU.
INT xfSdcDadeControl	1.3.6.1.4.1.193.81.3.4.3.1.10.1.4	INTEGER	read-write	SDC DADE procedure control.
INT xfSdcDadeStatus	1.3.6.1.4.1.193.81.3.4.3.1.10.1.5	INTEGER	read-only	SDC DADE procedure status.
INT xfSdcOperStatus	1.3.6.1.4.1.193.81.3.4.3.1.10.1.3	INTEGER	read-only	SDC Oper Status.
INT xfSdcPath	1.3.6.1.4.1.193.81.3.4.3.1.10.1.6	INTEGER	read-write	SDC selected path (desired value).
Integer32 (34)
I32 xfRauBoosterSelectedIndex	1.3.6.1.4.1.193.81.3.4.3.1.1.1.14	Integer32	read-write	This object represents the Booster selected index for a link.
I32 xfRAUTemperature	1.3.6.1.4.1.193.81.3.4.3.1.1.1.8	Integer32	read-only	This object shows the temperature, in degree Celsius, inside the radio unit.
I32 xfRFAtpcFallbackTimer	1.3.6.1.4.1.193.81.3.4.3.1.8.1.41	Integer32	read-write	This object specifies how long the output power can be at (ATPC, MAX) before ATPC fallback is triggered. Default value: ETSI 15 min, ANSI 5 min.
I32 xfRFAtpcMaxOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.6	Integer32	read-write	This object sets/shows the ATPC maximum output power in dBm for radio contained in the radio terminal. Value 254 indicates that the power is set to maximum. Default value: 254.
I32 xfRFAtpcMinInputPowerFar	1.3.6.1.4.1.193.81.3.4.3.1.3.1.7	Integer32	read-only	This object shows the ATPC minimum input target power level for far end radio.
I32 xfRFAtpcMinOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.5	Integer32	read-only	This object shows the minimum output power in dBm in ATPC. mode for radio contained in the radio terminal.
I32 xfRFAtpcSelectedInputPowerFar	1.3.6.1.4.1.193.81.3.4.3.1.3.1.8	Integer32	read-write	This object sets/shows the ATPC selected input target level for far end radio. Default value: -30.
I32 xfRfAtpcTargetInputPowerFE	1.3.6.1.4.1.193.81.3.4.3.1.8.1.6	Integer32	read-write	ATPC target input power on Far End side. Default value: -30.
I32 xfRFAttenuator	1.3.6.1.4.1.193.81.3.4.3.1.3.1.9	Integer32	read-write	This object sets/shows the value in dBm for fixed attenuator mounted in antenna. Default value: 0.
I32 xfRFBoosterGain	1.3.6.1.4.1.193.81.3.4.3.1.3.1.43	Integer32	read-only	Value of the Gain of the Booster
I32 xfRFBoosterMaxInputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.44	Integer32	read-only	Value of the Max Input Power admitted towards the Booster
I32 xfRFDegradationValue	1.3.6.1.4.1.193.81.3.4.3.1.9.1.20	Integer32	read-only	This object handles the value calculated on 24h for Degradation Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access.
I32 xfRFDuplexDistance	1.3.6.1.4.1.193.81.3.4.3.1.2.1.18	Integer32	read-write	This object is aimed to select the duplex distance for the RAU. It can only be set if xfRFDuplexConfig = enabled(2), so that: xfRFDuplexDistance = Tx Frequency - Rx Frequency Otherwise, it is automatically filled on the basis of Tx and Rx frequency settings, and can not be overwritten.
I32 xfRFInputAlarmThreshold	1.3.6.1.4.1.193.81.3.4.3.1.8.1.13	Integer32	read-write	RF input level threshold. Default value: -93.
I32 xfRFMarginValue	1.3.6.1.4.1.193.81.3.4.3.1.9.1.21	Integer32	read-only	This object handles the value calculated on 24h for Margin Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access.
I32 xfRFMaxMSELast7Days	1.3.6.1.4.1.193.81.3.4.3.1.3.1.38	Integer32	read-only	Indicate Max MSE level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.
I32 xfRFMaxOutputPowerLast7Days	1.3.6.1.4.1.193.81.3.4.3.1.8.1.27	Integer32	read-only	This object shows maximum RF output level last 7 days. RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.
I32 xfRFMaxOutputPowerSinceReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.29	Integer32	read-only	This object shows maximum RF output level since reset RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.
I32 xfRFMaxXPILast7Days	1.3.6.1.4.1.193.81.3.4.3.1.3.1.40	Integer32	read-only	Indicate Max Cross-Polar Interference (XPI) level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.
I32 xfRFMeanInputPower1m	1.3.6.1.4.1.193.81.3.4.3.1.8.1.26	Integer32	read-only	This object shows RF input mean level for last minute. RF input level = value/10 dBm. Domain: [-99.9 ... -20.0 dBm] 0 (zero) indicates invalid value.
I32 xfRFMinMSELast7Days	1.3.6.1.4.1.193.81.3.4.3.1.3.1.39	Integer32	read-only	Indicate Min MSE level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.
I32 xfRFMinOutputPowerLast7Days	1.3.6.1.4.1.193.81.3.4.3.1.8.1.28	Integer32	read-only	This object shows minimum RF output level last 7 days. RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.
I32 xfRFMinOutputPowerSinceReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.30	Integer32	read-only	This object shows minimum RF output level since reset RF output level = value dBm. Domain: [-100 ... 45 dBm] 255 indicates invalid value.
I32 xfRFMinXPILast7Days	1.3.6.1.4.1.193.81.3.4.3.1.3.1.41	Integer32	read-only	Indicate Min Cross-Polar Interference (XPI) level last 7 days. Input level = value/10 dB. Domain: [-100.0 ... 100.0 dB] 2000 indicates invalid value.
I32 xfRFOutlierValue	1.3.6.1.4.1.193.81.3.4.3.1.9.1.17	Integer32	read-only	This object handles the value calculated on 24h for Outlier Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 Near end access: read-write. Far end access: no access.
I32 xfRFOutputPower8QAM	1.3.6.1.4.1.193.81.3.4.3.1.3.1.18	Integer32	read-only	Output power for 8QAM.
I32 xfRFRangeValue	1.3.6.1.4.1.193.81.3.4.3.1.9.1.18	Integer32	read-only	This object handles the value calculated on 24h for Range Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access.
I32 xfRFRtpcMaxOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.3	Integer32	read-only	This object shows the maximum output power in dBm including attenuator. Value -100 indicate that RAU Tx on is not possible due to power supply limitations.
I32 xfRFRtpcMinOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.2	Integer32	read-only	This object shows the minimum output power in dBm including attenuator. Value -100 indicate that RAU Tx on is not possible due to power supply limitations.
I32 xfRFRtpcSelectedOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.3.1.4	Integer32	read-write	This object set/shows the selected output power in dBm including attenuator. Value 254 indicates that the selected power is set to maximum. Default value: 254
I32 xfRFSpectrumDiagResultRxPower	1.3.6.1.4.1.193.81.3.4.3.1.7.1.3	Integer32	read-only	Spectrum Diagnostics Scan Result Rx Power value/10 dBm Domain: [-99.9 .. -20.0 dBm]
I32 xfRFStddevValue	1.3.6.1.4.1.193.81.3.4.3.1.9.1.19	Integer32	read-only	This object handles the value calculated on 24h for Stddev Alarm. 0 = Default value (0). - To calculate value use the following formula: Value/100. Default value: 0 (dB/100) Near end access: read-write. Far end access: no access.
I32 xfSdcDadeDelay	1.3.6.1.4.1.193.81.3.4.3.1.10.1.11	Integer32	read-only	DADE delay in nsec.
I32 xfSdcGain	1.3.6.1.4.1.193.81.3.4.3.1.10.1.9	Integer32	read-only	SDC gain in dB/10. Domain: [0.0 .. 3.0 dB].
OCTET STRING (1)
OCT xfRAUNotes	1.3.6.1.4.1.193.81.3.4.3.1.1.1.11	OCTET STRING	read-write	You can add information in this description field, for example polarization, antenna type or logging a site visit.
RAUAtpcCapability (1)
RAU xfRAUAtpcCapability	1.3.6.1.4.1.193.81.3.4.3.1.1.1.3	RAUAtpcCapability	read-only	This object indicates if the radio unit supports ATPC or not.
RAUChannelSpacingCapability (1)
RAU xfRAUChannelSpacing	1.3.6.1.4.1.193.81.3.4.3.1.4.1.1	RAUChannelSpacingCapability	read-only	Channel spacing. ETSI: 3.5, 7, 14, 28, 40, 56 MHz ANSI: 10, 20, 30, 40, 50 MHz
RAUModCapability (1)
RAU xfRAUModCapability	1.3.6.1.4.1.193.81.3.4.3.1.1.1.5	RAUModCapability	read-only	This object shows the modulation methods supported by the radio unit.
RAUModulation (1)
RAU xfRAUChannelModulation	1.3.6.1.4.1.193.81.3.4.3.1.4.1.2	RAUModulation	read-only	This object shows the modulation. Values: cqpsk(2) CQPSK qam16(3) 16-QAM qam128(4) 128-QAM qam32(5) 32-QAM qam64(6) 64-QAM qam4(7) 4-QAM qam8(8) 8-QAM qam256(9) 256-QAM qam512(10) 512-QAM qam1024(11) 1024-QAM
RAURfLoopAvailable (1)
RAU xfRAURfLoopAvailable	1.3.6.1.4.1.193.81.3.4.3.1.1.1.2	RAURfLoopAvailable	read-only	This object inidicates if RF loop is available in radio unit.
RauSec (1)
RAU xfRAUSpectrumEfficiencyClass	1.3.6.1.4.1.193.81.3.4.3.1.4.1.3	RauSec	read-only	Spectrum Efficiency Class: other(1), unknown sec2(2), Spectrum eff. Class 2 sec3(3), Spectrum eff. Class 3 sec4L(4), Spectrum eff. Class 4L sec4H(5), Specturm eff. Class 4H sec5A(6), Spectrum eff. Class 5A sec5B(7), Spectrum eff. Class 5B sec6A(8), Spectrum eff. Class 6A sec6B(9) Spectrum eff. Class 6B
RfInputPower (7)
RFI xfRFCurrentInputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.7	RfInputPower	read-only	RF input level. Value is in 1/10 dBm. Domain: [-20.0 .. -99.9 dBm].
RFI xfRFCurrentInputPowerSdcDiv	1.3.6.1.4.1.193.81.3.4.3.1.8.1.36	RfInputPower	read-only	This object shows RF input level for SDC Diversity path = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. 0 (zero) indicates invalid value (e.g. SDC not available).
RFI xfRFCurrentInputPowerSdcMain	1.3.6.1.4.1.193.81.3.4.3.1.8.1.35	RfInputPower	read-only	This object shows RF input level for SDC Main path = value/10 dBm. Domain: [-20.0 .. -99.9 dBm]. 0 (zero) indicates invalid value (e.g. SDC not available).
RFI xfRFMaxInputPowerLast7Days	1.3.6.1.4.1.193.81.3.4.3.1.8.1.8	RfInputPower	read-only	Maximum RF input level in the last 7 days. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.
RFI xfRFMaxInputPowerSinceReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.10	RfInputPower	read-only	Maximum RF input level since reset. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.
RFI xfRFMinInputPowerLast7Days	1.3.6.1.4.1.193.81.3.4.3.1.8.1.9	RfInputPower	read-only	Minimum RF input level in the last 7 days. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.
RFI xfRFMinInputPowerSinceReset	1.3.6.1.4.1.193.81.3.4.3.1.8.1.11	RfInputPower	read-only	Minimum RF input level since reset. Value is in 1/10 dBm. Domain: [-99.9 ... -20.0 dBm]. 0 (zero) indicates an invalid value.
RfOutputPower (19)
RFO xfRFAtpcFallbackOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.39	RfOutputPower	read-write	This object sets output power (in dBm) in ATPCFallback mode, for radio contained in the Carrier Termination. 255 indicates invalid value.
RFO xfRFCurrentOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.3	RfOutputPower	read-only	Current output power in dBm. 255 indicates invalid value.
RFO xfRfMaxOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.5	RfOutputPower	read-only	Maximum output power in dBm (provided by RAU). 255 indicates invalid value.
RFO xfRFMaxOutputPowerNotLimited	1.3.6.1.4.1.193.81.3.4.3.1.8.1.24	RfOutputPower	read-only	Max output power in dBm that the RAU can give if it is not power supply limited. 255 indicates invalid value.
RFO xfRfMinOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.4	RfOutputPower	read-only	Minimum output power in dBm (provided by RAU). 255 indicates invalid value.
RFO xfRFOutputPower1024QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.21	RfOutputPower	read-only	Output power for 1024QAM. 255 indicates invalid value.
RFO xfRFOutputPower128QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.18	RfOutputPower	read-only	Output power for 128QAM. 255 indicates invalid value.
RFO xfRfOutputPower16384QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.38	RfOutputPower	read-only	Output power for 16384QAM. 255 indicates invalid value.
RFO xfRFOutputPower16QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.15	RfOutputPower	read-only	Output power for 16QAM. 255 indicates invalid value.
RFO xfRfOutputPower2048QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.22	RfOutputPower	read-only	Output power for 2048QAM. 255 indicates invalid value.
RFO xfRFOutputPower256QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.19	RfOutputPower	read-only	Output power for 256QAM. 255 indicates invalid value.
RFO xfRFOutputPower32QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.16	RfOutputPower	read-only	Output power for 32QAM. 255 indicates invalid value.
RFO xfRfOutputPower4096QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.23	RfOutputPower	read-only	Output power for 4096QAM. 255 indicates invalid value.
RFO xfRFOutputPower4QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.14	RfOutputPower	read-only	Output power for 4QAM. 255 indicates invalid value.
RFO xfRFOutputPower512QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.20	RfOutputPower	read-only	Output power for 512QAM. 255 indicates invalid value.
RFO xfRFOutputPower64QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.17	RfOutputPower	read-only	Output power for 64QAM. 255 indicates invalid value.
RFO xfRfOutputPower8192QAM	1.3.6.1.4.1.193.81.3.4.3.1.8.1.37	RfOutputPower	read-only	Output power for 8192QAM. 255 indicates invalid value.
RFO xfRfSelectedMaxOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.2	RfOutputPower	read-write	Maximum output power in dBm (selected by operator). Default value: 10 dBm.
RFO xfRfSelectedMinOutputPower	1.3.6.1.4.1.193.81.3.4.3.1.8.1.1	RfOutputPower	read-write	Minimum output power in dBm (selected by operator). Default value: 10 dBm.
RFTxOperStatus (1)
RFT xfRFTxOperStatus	1.3.6.1.4.1.193.81.3.4.3.1.2.1.7	RFTxOperStatus	read-only	This object shows the operational status of the transmitter.
Unsigned32 (36)
U32 xfRAUFrequencyband	1.3.6.1.4.1.193.81.3.4.3.1.1.1.6	Unsigned32	read-only	This object shows the frequency band for the radio unit.
U32 xfRAUSubBand	1.3.6.1.4.1.193.81.3.4.3.1.1.1.7	Unsigned32	read-write	This object shows the sub band (Index) for the radio unit.
U32 xfRAUSubBandIndex	1.3.6.1.4.1.193.81.3.4.3.1.5.1.1	Unsigned32	read-only	An index for the specific RAU Sub-Band available index range.
U32 xfRAUSubBandRange	1.3.6.1.4.1.193.81.3.4.3.1.5.1.2	Unsigned32	read-only	This object shows the RAU Sub-Band available index range [0..255].
U32 xfRFBaseRxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.2.1.2	Unsigned32	read-only	This object shows the Rx frequency in KHz when frequency. step number is 0
U32 xfRFBaseTxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.2.1.1	Unsigned32	read-only	This object shows the Tx frequency in KHz when frequency step number is 0.
U32 xfRFCurrentStepNumber	1.3.6.1.4.1.193.81.3.4.3.1.2.1.6	Unsigned32	read-write	This object sets/shows the frequency step number. 0 = frequency not yet defined. For Classic RAUs, TX and RX frequencies can not be set individually. The span between them is always fixed and depends on different frequency and sub band. - To calculate step number for TX and RX, use the following formulas: New step number = (TX frequency - XfRAUBaseTxFrequency) / XfRAUStepSize New step number = (RX frequency - xfRAUBaseRxFrequency) / XfRAUStepSize - To calculate TX and RX frequencies, use the following formulas: TX frequency = XfRAUBaseTxFrequency + XfRAUCurrentStepNumber * XfRAUStepSize RX frequency = XfRAUBaseRxFrequency + XfRAUCurrentStepNumber * XfRAUStepSize For Agile RAUs, the TX and RX frequencies can be set individually. Above formulas are only valid for TX frequency. For RX frequency, xfRFCurrentStepNumberRx must be used. Default value: 0
U32 xfRFCurrentStepNumberRx	1.3.6.1.4.1.193.81.3.4.3.1.2.1.15	Unsigned32	read-write	This object sets/shows the RX frequency step number for Agile RAUs. 0 = frequency not yet defined. - To calculate step number for RX, use the following formula: New step number Rx = (RX frequency - xfRAUBaseRxFrequency) / XfRAUStepSizeRx - To calculate RX frequency, use the following formula: RX frequency = XfRAUBaseRxFrequency + XfRAUCurrentStepNumberRx * XfRAUStepSizeRx Default value: 0
U32 xfRFDegradationCeaseTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.13	Unsigned32	read-write	This object handles Cease Threshold for Degradation Alarm. 1 = Default value (0.1). - To calculate threshold use the following formula: SetTh/10. Default value: 1 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFDegradationSetTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.12	Unsigned32	read-write	This object handles Set Threshold for Degradation Alarm. 2 = Default value (0.2). - To calculate threshold use the following formula: SetTh/10. Default value: 2 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFMarginCeaseTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.16	Unsigned32	read-write	This object handles Cease Threshold for Margin Alarm. 60 = Default value (6). - To calculate threshold use the following formula: SetTh/10. Default value: 60 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFMarginSetTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.15	Unsigned32	read-write	This object handles Set Threshold for Margin Alarm. 30 = Default value (3). - To calculate threshold use the following formula: SetTh/10. Default value: 30 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFOutlierCeaseTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.4	Unsigned32	read-write	This object handles Cease Threshold for Outlier Alarm. 2 = Default value (0.2). - To calculate threshold use the following formula: SetTh/10. Default value: 2 Near end access: read-write. Far end access: no access.
U32 xfRFOutlierSetTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.3	Unsigned32	read-write	This object handles Set Threshold for Outlier Alarm. 3 = Default value (0.3). - To calculate threshold use the following formula: SetTh/10. Default value: 3 Near end access: read-write. Far end access: no access.
U32 xfRFRangeCeaseTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.7	Unsigned32	read-write	This object handles Cease Threshold for Range Alarm. 20 = Default value (2). - To calculate threshold use the following formula: SetTh/10. Default value: 20 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFRangeSetTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.6	Unsigned32	read-write	This object handles Set Threshold for Range Alarm. 30 = Default value (3). - To calculate threshold use the following formula: SetTh/10. Default value: 30 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFSpectrumDiagChannelScanEstTime	1.3.6.1.4.1.193.81.3.4.3.1.6.1.3	Unsigned32	read-only	Estimated time in seconds for scanning one Channel Spacing at current RX frequency
U32 xfRFSpectrumDiagChannelSpacing	1.3.6.1.4.1.193.81.3.4.3.1.6.1.6	Unsigned32	read-only	Channel width measured by Spectrum Diagnostics
U32 xfRFSpectrumDiagCurrRxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.6.1.7	Unsigned32	read-only	Current value of Rx frequency
U32 xfRFSpectrumDiagIdxCompanion1	1.3.6.1.4.1.193.81.3.4.3.1.6.1.10	Unsigned32	read-only	RF IF index for 1st companion carrier (0 if no companion)
U32 xfRFSpectrumDiagIdxCompanion2	1.3.6.1.4.1.193.81.3.4.3.1.6.1.11	Unsigned32	read-only	RF IF index for 2nd companion carrier (0 if no companion)
U32 xfRFSpectrumDiagIdxCompanion3	1.3.6.1.4.1.193.81.3.4.3.1.6.1.12	Unsigned32	read-only	RF IF index for 3rd companion carrier (0 if no companion)
U32 xfRFSpectrumDiagMaxRxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.6.1.9	Unsigned32	read-only	Maximum sub-band Rx frequency (RAU upper edge)
U32 xfRFSpectrumDiagMinRxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.6.1.8	Unsigned32	read-only	Minimum sub-band Rx frequency (RAU lower edge)
U32 xfRFSpectrumDiagProgress	1.3.6.1.4.1.193.81.3.4.3.1.6.1.13	Unsigned32	read-only	Completed percentage of Spectrum Diagnostics scan
U32 xfRFSpectrumDiagResultIndex	1.3.6.1.4.1.193.81.3.4.3.1.7.1.1	Unsigned32	read-only	Spectrum Diagnostics Scan Result Index
U32 xfRFSpectrumDiagResultRxFrequency	1.3.6.1.4.1.193.81.3.4.3.1.7.1.2	Unsigned32	read-only	Spectrum Diagnostics Scan Result Rx frequency in kHz
U32 xfRFSpectrumDiagSubBandScanEstTime	1.3.6.1.4.1.193.81.3.4.3.1.6.1.4	Unsigned32	read-only	Estimated time in seconds for scanning full Sub Band of connected RAU
U32 xfRFStddevCeaseTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.10	Unsigned32	read-write	This object handles Cease Threshold for Stddev Alarm. 20 = Default value (2). - To calculate threshold use the following formula: SetTh/10. Default value: 20 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFStddevSetTh	1.3.6.1.4.1.193.81.3.4.3.1.9.1.9	Unsigned32	read-write	This object handles Set Threshold for Stddev Alarm. 50 = Default value (5). - To calculate threshold use the following formula: SetTh/10. Default value: 50 (dB/10) Near end access: read-write. Far end access: no access.
U32 xfRFStepLimitHigh	1.3.6.1.4.1.193.81.3.4.3.1.2.1.5	Unsigned32	read-only	This object shows the highest allowed frequency step number.
U32 xfRFStepLimitHighRx	1.3.6.1.4.1.193.81.3.4.3.1.2.1.14	Unsigned32	read-only	This object shows the Rx highest allowed frequency step number.
U32 xfRFStepLimitLow	1.3.6.1.4.1.193.81.3.4.3.1.2.1.4	Unsigned32	read-only	This object shows the lowest allowed frequency step number.
U32 xfRFStepLimitLowRx	1.3.6.1.4.1.193.81.3.4.3.1.2.1.13	Unsigned32	read-only	This object shows the Rx lowest allowed frequency step number.
U32 xfRFStepSize	1.3.6.1.4.1.193.81.3.4.3.1.2.1.3	Unsigned32	read-only	This object shows the frequency step size in KHz.
U32 xfRFStepSizeRx	1.3.6.1.4.1.193.81.3.4.3.1.2.1.12	Unsigned32	read-only	This object shows the Rx frequency step size in KHz.
No type (27)
xfRadioLinkPtpRadioCompleteGroup	1.3.6.1.4.1.193.81.3.4.3.2.2.1			A collection of all current objects in this MIB module.
xfRadioLinkPtpRadioCompliances	1.3.6.1.4.1.193.81.3.4.3.2.1
xfRadioLinkPtpRadioConformance	1.3.6.1.4.1.193.81.3.4.3.2
xfRADIOLINKPTPRADIOFullCompliance	1.3.6.1.4.1.193.81.3.4.3.2.1.1			The compliance statement for SNMP entities which implement everything.
xfRadioLinkPtpRadioGroups	1.3.6.1.4.1.193.81.3.4.3.2.2
xfRadioLinkPtpRadioMIB	1.3.6.1.4.1.193.81.3.4.3			This MIB defines objects for point-to-point Radio Link RAUs.
xfRadioLinkPtpRadioObjects	1.3.6.1.4.1.193.81.3.4.3.1
xfRAUCapabilityEntry	1.3.6.1.4.1.193.81.3.4.3.1.4.1		not-accessible	An entry in xfRAUCapabilityTable.
xfRAUCapabilityTable	1.3.6.1.4.1.193.81.3.4.3.1.4		not-accessible	Table for RAU capability information. Table indexed with entPhysicalIndex and xfTermRowIndex.
xfRAUEntry	1.3.6.1.4.1.193.81.3.4.3.1.1.1		not-accessible	An entry in xfRadioTable.
xfRAUSubBandEntry	1.3.6.1.4.1.193.81.3.4.3.1.5.1		not-accessible	An entry in xfRAUSubBandTable.
xfRAUSubBandTable	1.3.6.1.4.1.193.81.3.4.3.1.5		not-accessible	Table for RAU Sub-Band index capability. Table indexed with entPhysicalIndex and xfRAUSubBandIndex.
xfRAUTable	1.3.6.1.4.1.193.81.3.4.3.1.1		not-accessible	Table for Radiolink point-to-point radios managed objects. Table indexed with entPhysicalIndex.
xfRFIFCableMonitoringEntry	1.3.6.1.4.1.193.81.3.4.3.1.9.1		not-accessible	An entry in the xfRFIFCableMonitoringTable.
xfRFIFCableMonitoringTable	1.3.6.1.4.1.193.81.3.4.3.1.9		not-accessible	Table for Radiolink point-to-point radios RF IF Cable Monitoring managed objects. Table indexed with ifIndex.
xfRFIFEntry	1.3.6.1.4.1.193.81.3.4.3.1.2.1		not-accessible	An entry in the xfRFIFTable.
xfRfIfPowerEntry	1.3.6.1.4.1.193.81.3.4.3.1.8.1		not-accessible	An entry in the xfRfIfPowerTable.
xfRfIfPowerTable	1.3.6.1.4.1.193.81.3.4.3.1.8		not-accessible	Table for Radio Link RAU managed objects. Table indexed with ifIndex.
xfRFIFTable	1.3.6.1.4.1.193.81.3.4.3.1.2		not-accessible	Table for Radiolink point-to-point radios RF IF managed objects. Table indexed with ifIndex.
xfRFPowerEntry	1.3.6.1.4.1.193.81.3.4.3.1.3.1		not-accessible	An entry in the xfRFPowerTable.
xfRFPowerTable	1.3.6.1.4.1.193.81.3.4.3.1.3		not-accessible	Table for Radiolink point-to-point radios managed objects. Table indexed with ifIndex.
xfRFSpectrumDiagEntry	1.3.6.1.4.1.193.81.3.4.3.1.6.1		not-accessible	An entry in xfRFSpectrumDiagTable
xfRFSpectrumDiagResultEntry	1.3.6.1.4.1.193.81.3.4.3.1.7.1		not-accessible	An entry in xfRFSpectrumDiagResultTable
xfRFSpectrumDiagResultTable	1.3.6.1.4.1.193.81.3.4.3.1.7		not-accessible	Table of Spectrum Diagnostics scan results
xfRFSpectrumDiagTable	1.3.6.1.4.1.193.81.3.4.3.1.6		not-accessible	Table for RF Spectrum Diagnostics control and status
xfSdcEntry	1.3.6.1.4.1.193.81.3.4.3.1.10.1		not-accessible	An entry in the xfSdcTable.
xfSdcTable	1.3.6.1.4.1.193.81.3.4.3.1.10		not-accessible	Table for SDC capabilities, setting and status.

RFC description

Manages point-to-point radio link Remote Access Units (RAUs) for Ericsson transmission and transport networks, including RF power and modulation settings.

Start monitoring Ericsson XF/MINI-LINK point-to-point microwave radio unit (TX-power/RX-signal-level status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download XF-RADIOLINK-PTP-RADIO-MIB

This MIB depends on

Related MIBs

What Is XF-RADIOLINK-PTP-RADIO-MIB?

What Can Be Monitored

Supported Devices

Monitoring Examples

RFC description