Wellfleet-X25-MIB

All MIBs › Wellfleet-X25-MIB

Category: Wellfleet BayNetworks WAN Interfaces

Description: Manages Wellfleet X.25 packet-layer protocol parameters, virtual circuits, and packet statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-X25-MIB?

The Wellfleet-X25-MIB is a Wellfleet Communications proprietary MIB managing the X.25 packet-layer protocol on Wellfleet routers, covering virtual circuit setup and packet-level statistics for this legacy WAN packet-switching standard. It exposes configuration objects for X.25 virtual circuits (both switched and permanent) and counters tracking packets, resets, and clears at the packet layer. Its monitoring emphasis is on service/software health: operators use it to confirm virtual circuits are established and passing packets, and to detect abnormal reset or clear-request rates that indicate signaling problems or congestion within the X.25 network. It depends directly on the underlying Wellfleet-LAPB-MIB, since X.25's packet layer runs over LAPB's data-link layer on the same physical interface. It was deployed on Wellfleet/Bay Networks routers serving as X.25 PAD or gateway devices in legacy carrier, banking, and government X.25 networks. Network engineers evaluating or troubleshooting this functionality can download the Wellfleet-X25-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-X25-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet router
Bay Networks/Nortel router with X.25 WAN links

Monitoring Examples

An engineer polls the X.25 virtual circuit table to confirm a given permanent virtual circuit is in the active data-transfer state, then checks the packet statistics counters for resets and clear requests on that circuit. A circuit experiencing frequent resets while the underlying LAPB link stays connected typically points to a packet-layer parameter mismatch (such as window size or packet size) with the remote X.25 DTE.

What Can Be Monitored

X.25 virtual circuit state
packet/reset/clear counters
circuit provisioning parameters
packet-layer signaling errors

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress

From RFC1213-MIB

DisplayString

From Wellfleet-COMMON-MIB

wfX25Group

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
INT wfLapbPktAccFormat	1.3.6.1.4.1.18.3.5.9.4.5.1.30	INTEGER	read-write	Specifies the format of the call accepted packet.
INT wfLapbPktBackupDebugLvl	1.3.6.1.4.1.18.3.5.9.4.5.1.61	INTEGER	read-write	Debug level for X.25 backup messages
INT wfLapbPktBackupEnable	1.3.6.1.4.1.18.3.5.9.4.5.1.62	INTEGER	read-write	Backup Enable/Disable parameter
INT wfLapbPktBwcCnt	1.3.6.1.4.1.18.3.5.9.4.5.1.38	INTEGER	read-write	Number of BWC (Bidirectional VC's) defined on this access link.
INT wfLapbPktBwcId	1.3.6.1.4.1.18.3.5.9.4.5.1.39	INTEGER	read-write	Low LCN ID for BWC (Bidirectional VC's) defined on this access link.
INT wfLapbPktChargeInform	1.3.6.1.4.1.18.3.5.9.4.5.1.27	INTEGER	read-write	Specifies whether or not the charging information related facilities are supported. Outgoing calls will not contain the charge information related facility. But if set this packet layer will simply accept calls with the charge information related facility. No charging information will be collected.
INT wfLapbPktClientTimer	1.3.6.1.4.1.18.3.5.9.4.5.1.57	INTEGER	read-write	Client application response timeout period in seconds. This timer allows for the extended delays that can occur negotiating with remote clients (e.g., IPEX or QLLC). This timer must be greater than the wfLapbPktT3 period and less than wfLapbPktT2.
INT wfLapbPktConformance	1.3.6.1.4.1.18.3.5.9.4.5.1.46	INTEGER	read-write	CCITT conformance recommendation used on each line.
INT wfLapbPktConnector	1.3.6.1.4.1.18.3.5.9.4.5.1.4	INTEGER	read-only	Instance identifier. This is the Physical connector number for the Physical layer associated with this X25 Packet layer.
INT wfLapbPktCugBilateral	1.3.6.1.4.1.18.3.5.9.4.5.1.25	INTEGER	read-write	Specifies whether or not Bilateral Closed User Group related facility is supported. If this is set, then the wfLapbPktCugSelection should be set to EXTENDED.
INT wfLapbPktCugOA	1.3.6.1.4.1.18.3.5.9.4.5.1.24	INTEGER	read-write	Specifies whether or not CUG with Outgoing access selection facility is supported.
INT wfLapbPktCugSelection	1.3.6.1.4.1.18.3.5.9.4.5.1.23	INTEGER	read-write	Format of the Closed User Group (CUG) related facilities supported.
IP wfLapbPktDDNIpAddr	1.3.6.1.4.1.18.3.5.9.4.5.1.51	IpAddress	read-write	If the wfLapbPktNetaddrType is DDNTYPE or DDN_BFE this is the user supplied local IP address. The router will convert this to the corresponding X121 address and the X121 address value will be put in wfLapbPktNetaddr attribute.
INT wfLapbPktDefClass	1.3.6.1.4.1.18.3.5.9.4.5.1.44	INTEGER	read-write	Non standard default transmit/receive throughput class assignment.
INT wfLapbPktDefLength	1.3.6.1.4.1.18.3.5.9.4.5.1.43	INTEGER	read-write	Non standard default transmit/receive packet size. This attribute should not be greater than the wfSyncEntry attribute wfSyncMtu.
INT wfLapbPktDefWindow	1.3.6.1.4.1.18.3.5.9.4.5.1.42	INTEGER	read-write	Non standard default transmit/receive window size.
INT wfLapbPktDelete	1.3.6.1.4.1.18.3.5.9.4.5.1.1	INTEGER	read-write	Create/Delete parameter. Default is created.
INT wfLapbPktDisable	1.3.6.1.4.1.18.3.5.9.4.5.1.2	INTEGER	read-write	Enable/Disable parameter
INT wfLapbPktDxe	1.3.6.1.4.1.18.3.5.9.4.5.1.45	INTEGER	read-write	Specify type of local X25 interface and imply subsequent rules of X.25. DXE_X25DTERSTA ->DTE mode with Restart Procedure. DXE_X25DTE ->DTE mode without any restart procedure DXE_X25DCE ->DCE mode with restart procedure DXE_X25DTEDXE ->DTE/DTE environment, unassigned roles.
wfLapbPktEntry	1.3.6.1.4.1.18.3.5.9.4.5.1		not-accessible	An entry in the LAPB PKT table
INT wfLapbPktFastAccept	1.3.6.1.4.1.18.3.5.9.4.5.1.19	INTEGER	read-write	Specifies whether or not (ON/OFF) fast select acceptance facility is subscribed too.
INT wfLapbPktFastSelect	1.3.6.1.4.1.18.3.5.9.4.5.1.21	INTEGER	read-write	Specifies whether or not (ON/OFF) fast select facility is allowed on a per call basis.
INT wfLapbPktFlowCtl	1.3.6.1.4.1.18.3.5.9.4.5.1.14	INTEGER	read-write	Flow control parameter negotiation facility subscription
INT wfLapbPktFullAddressing	1.3.6.1.4.1.18.3.5.9.4.5.1.29	INTEGER	read-write	If this attribute is set, the full local X121 address (calling address) is supplied in the outgoing call request and the X.25 network also expected to provide the full called address in the incoming call packet.
INT wfLapbPktInCalls	1.3.6.1.4.1.18.3.5.9.4.5.1.17	INTEGER	read-write	Specifies whether or not (ON/OFF) incoming calls are permitted
INT wfLapbPktIwcCnt	1.3.6.1.4.1.18.3.5.9.4.5.1.36	INTEGER	read-write	Number of IWC (Incoming VC's) defined on this access link.
INT wfLapbPktIwcId	1.3.6.1.4.1.18.3.5.9.4.5.1.37	INTEGER	read-write	Low LCN ID for IWC (Incoming VC's) defined on this access link.
INT wfLapbPktLapbCct	1.3.6.1.4.1.18.3.5.9.4.5.1.7	INTEGER	read-only	Circuit number of Lapb (SYNC) driver associated with this X25 Packet Layer
INT wfLapbPktLineNumber	1.3.6.1.4.1.18.3.5.9.4.5.1.5	INTEGER	read-only	Instance identifier. This is the line number assigned to the LAPB Driver associated with this X25 Packet Layer. Not used in 7.60
INT wfLapbPktLineState	1.3.6.1.4.1.18.3.5.9.4.5.1.9	INTEGER	read-only	Reflects the state of the X.25 packet layer that is associated with this network record. When the state of this parameter is set to Up, the router can transfer data between the line layer and the packet layer. Note that this parameter is used internally; it does NOT reflect the status of the underlying synchronous circuit.
INT wfLapbPktLinkId	1.3.6.1.4.1.18.3.5.9.4.5.1.8	INTEGER	read-only	Access Link identifier - index into line information array.
INT wfLapbPktLLIndex	1.3.6.1.4.1.18.3.5.9.4.5.1.6	INTEGER	read-only	Instance identifier. This is the lower layer index presented to X25 by the layer immediately below it on the protocol stack. If the lower layer is a driver, the index will be 0. Not used in 7.60.
INT wfLapbPktMaxLength	1.3.6.1.4.1.18.3.5.9.4.5.1.12	INTEGER	read-write	Maximum packet length that can be negotiated on a per call basis, if the flow control facility is subscribed too. This attribute is effective only if the attribute wfLapbPktFloCtl is set to 'ON'. This attribute should not be greater than the wfSYNCEntry attribute wfSyncMtu.
INT wfLapbPktMaxThroughput	1.3.6.1.4.1.18.3.5.9.4.5.1.13	INTEGER	read-write	Maximum throughput class value that can be negotiated on a per call basis, if the throughput class negotiation facility is subscribed too. For this to be effective the attribute wfLapbPktThroughput must be set to ON.
INT wfLapbPktMaxWindow	1.3.6.1.4.1.18.3.5.9.4.5.1.11	INTEGER	read-write	Maximum window size that can be negotiated on a per call basis, if the flow control facility is subscribed too. Extended window size of 127 can be used if wfLapbPktSeqSize is 128. Otherwise the maximum is 7. This attribute is effective only if the attribute wfLapbPktFloCtl is set to 'ON'.
STR wfLapbPktNetaddr	1.3.6.1.4.1.18.3.5.9.4.5.1.48	DisplayString	read-only	This Link's Network address (X121 address).
INT wfLapbPktNetaddrType	1.3.6.1.4.1.18.3.5.9.4.5.1.50	INTEGER	read-write	This defines whether the Network connection is to a DDN network or PDN Network. This is used to decide how the Local X121 Network address is derived. If this attribute is set to DDN the Local X121 address used in the attribute wfLapbPktNetaddr will be derived from the user supplied IP address. Otherwise the X121 address should be supplid by the user.
INT wfLapbPktOutCalls	1.3.6.1.4.1.18.3.5.9.4.5.1.18	INTEGER	read-write	Specifies whether or not (ON/OFF) outgoing calls are permitted
INT wfLapbPktOwcCnt	1.3.6.1.4.1.18.3.5.9.4.5.1.40	INTEGER	read-write	Number of OWC (Outgoing VC's) defined on this access link.
INT wfLapbPktOwcId	1.3.6.1.4.1.18.3.5.9.4.5.1.41	INTEGER	read-write	Low LCN ID for OWC (Outgoing VC's) defined on this access link.
STR wfLapbPktPDNX121Addr	1.3.6.1.4.1.18.3.5.9.4.5.1.52	DisplayString	read-write	If the wfLapbPktNetaddrType is PDNTYPE this is the user supplied local X.121 address. The router will put this value in wfLapbPktNetaddr attribute.
INT wfLapbPktPduSize	1.3.6.1.4.1.18.3.5.9.4.5.1.58	INTEGER	read-write	The X.25 PDU Size for this logical channel. This PDU size represents the M_BUF_SIZE used for X.25 Fragmentation and Reassembly in the packet layer. This is the largest message size X.25 will handle from a client on a given Logical Channel. Changing this attribute enables X.25 to handle client messages up to 4096 bytes in length
INT wfLapbPktPVCCnt	1.3.6.1.4.1.18.3.5.9.4.5.1.55	INTEGER	read-write	Number of PVCs defined on this access link.
INT wfLapbPktPVCLowLcn	1.3.6.1.4.1.18.3.5.9.4.5.1.56	INTEGER	read-write	Low LCN ID for PVCs defined on this access link.
INT wfLapbPktRelFormat	1.3.6.1.4.1.18.3.5.9.4.5.1.31	INTEGER	read-write	Connection release format - format of Clear Requests
INT wfLapbPktReverseAccept	1.3.6.1.4.1.18.3.5.9.4.5.1.20	INTEGER	read-write	Specifies whether or not (ON/OFF) reverse charge aceptance facility is subscribed to. If this is set this packet layer will simply accept calls with reverse charge facility. But the packet layer (router) will not provide any charging information.
INT wfLapbPktReverseCharging	1.3.6.1.4.1.18.3.5.9.4.5.1.22	INTEGER	read-write	Specifies whether or not (ON/OFF) reverse charging facility is allowed on a per call basis.
INT wfLapbPktRpoaSelection	1.3.6.1.4.1.18.3.5.9.4.5.1.26	INTEGER	read-write	Specifies whether or not RPOA related facility is supported. Outgoing calls will not contain any RPOA facility. But if set this packet layer will simply accept calls with RPOA related facility.
INT wfLapbPktSeqSize	1.3.6.1.4.1.18.3.5.9.4.5.1.10	INTEGER	read-write	Sequence numbering scheme for the data packets. Modulo 8 or Modulo 128
INT wfLapbPktSlotNum	1.3.6.1.4.1.18.3.5.9.4.5.1.3	INTEGER	read-only	Instance identifier. This is the slot number where this X.25 packet layer is running.
INT wfLapbPktStandard	1.3.6.1.4.1.18.3.5.9.4.5.1.47	INTEGER	read-write	Network Standard to be used on each line.
INT wfLapbPktStatistics	1.3.6.1.4.1.18.3.5.9.4.5.1.49	INTEGER	read-write	Gives the user the ability to Turn ON or Shut OFF statistics computation. This can be shut off for better performance on the line. Now it also provides a small packet trace function.
CTR wfLapbPktStatsAbnormalDisconnects	1.3.6.1.4.1.18.3.5.9.4.6.1.13	Counter	read-only	Number of Abnormal Virtual Circuit Disconnections.
CTR wfLapbPktStatsActiveMax	1.3.6.1.4.1.18.3.5.9.4.6.1.9	Counter	read-only	Highest number of active Virtual Circuits on this line.
CTR wfLapbPktStatsActiveVcs	1.3.6.1.4.1.18.3.5.9.4.6.1.8	Counter	read-only	Number of Active Virtual Circuits on this line.
CTR wfLapbPktStatsBytesRxs	1.3.6.1.4.1.18.3.5.9.4.6.1.34	Counter	read-only	Number of Data Bytes received.
CTR wfLapbPktStatsBytesTxs	1.3.6.1.4.1.18.3.5.9.4.6.1.23	Counter	read-only	Number of Data Bytes sent.
INT wfLapbPktStatsCct	1.3.6.1.4.1.18.3.5.9.4.6.1.5	INTEGER	read-only	Circuit number for this instance.
INT wfLapbPktStatsConnector	1.3.6.1.4.1.18.3.5.9.4.6.1.2	INTEGER	read-only	Port number and instance ID for this Lapb Packet Layer Line instance.
CTR wfLapbPktStatsDataRxs	1.3.6.1.4.1.18.3.5.9.4.6.1.25	Counter	read-only	Number of Data Packets received on this line.
CTR wfLapbPktStatsDataTxs	1.3.6.1.4.1.18.3.5.9.4.6.1.14	Counter	read-only	Number of Data Packets Transmitted on this line.
CTR wfLapbPktStatsDiagRxs	1.3.6.1.4.1.18.3.5.9.4.6.1.32	Counter	read-only	Number of Diagnostic Packets received.
CTR wfLapbPktStatsDiagTxs	1.3.6.1.4.1.18.3.5.9.4.6.1.21	Counter	read-only	Number of Diagnostic Packets sent.
wfLapbPktStatsEntry	1.3.6.1.4.1.18.3.5.9.4.6.1		not-accessible	Packet level statistics.
CTR wfLapbPktStatsFailedConnections	1.3.6.1.4.1.18.3.5.9.4.6.1.11	Counter	read-only	Number of unsuccessful Virtual Connections performed since start up.
CTR wfLapbPktStatsIntBytesRxs	1.3.6.1.4.1.18.3.5.9.4.6.1.35	Counter	read-only	Number of Interrupt Data Bytes received.
CTR wfLapbPktStatsIntBytesTxs	1.3.6.1.4.1.18.3.5.9.4.6.1.24	Counter	read-only	Number of Interrupt Data Bytes sent.
CTR wfLapbPktStatsInterruptRxs	1.3.6.1.4.1.18.3.5.9.4.6.1.26	Counter	read-only	Number of Interrupt Packets received.
CTR wfLapbPktStatsInterruptTxs	1.3.6.1.4.1.18.3.5.9.4.6.1.15	Counter	read-only	Number of Interrupt Packets sent.
STR wfLapbPktStatsLineAddress	1.3.6.1.4.1.18.3.5.9.4.6.1.6	DisplayString	read-only	The local X.121 address of this line.
INT wfLapbPktStatsLineNumber	1.3.6.1.4.1.18.3.5.9.4.6.1.3	INTEGER	read-only	Instance identifier member. This is the line number assigned to the driver X.25 is running over. No used in 7.60
INT wfLapbPktStatsLLIndex	1.3.6.1.4.1.18.3.5.9.4.6.1.4	INTEGER	read-only	Instance identifier member. This is the lower layer index presented to X25 by the layer immediately below it on the protocol stack. If the lower layer is a driver, the index will be 0. Not used in 7.60.
CTR wfLapbPktStatsMaxVcs	1.3.6.1.4.1.18.3.5.9.4.6.1.7	Counter	read-only	Maximum number of Virtual Circuits allowed on this line.
CTR wfLapbPktStatsNormalDisconnects	1.3.6.1.4.1.18.3.5.9.4.6.1.12	Counter	read-only	Number of Normal Virtual Circuit Disconnections.
INT wfLapbPktStatsOnOffSwitch	1.3.6.1.4.1.18.3.5.9.4.6.1.36	INTEGER	read-only	This tells the user if Statistics Computation is turned ON or OFF.
CTR wfLapbPktStatsRejectRxs	1.3.6.1.4.1.18.3.5.9.4.6.1.30	Counter	read-only	Number of Reject Packets received.
CTR wfLapbPktStatsRejectTxs	1.3.6.1.4.1.18.3.5.9.4.6.1.19	Counter	read-only	Number of Reject Packets sent.
CTR wfLapbPktStatsResetRxs	1.3.6.1.4.1.18.3.5.9.4.6.1.27	Counter	read-only	Number of Reset Requests received.
CTR wfLapbPktStatsResetTxs	1.3.6.1.4.1.18.3.5.9.4.6.1.16	Counter	read-only	Number of Reset Requests sent.
CTR wfLapbPktStatsRestartRxs	1.3.6.1.4.1.18.3.5.9.4.6.1.31	Counter	read-only	Number of Restart Packets received.
CTR wfLapbPktStatsRestartTxs	1.3.6.1.4.1.18.3.5.9.4.6.1.20	Counter	read-only	Number of Restart Packets sent.
CTR wfLapbPktStatsRnrRxs	1.3.6.1.4.1.18.3.5.9.4.6.1.29	Counter	read-only	Number of Receiver Not Ready Packets received.
CTR wfLapbPktStatsRnrTxs	1.3.6.1.4.1.18.3.5.9.4.6.1.18	Counter	read-only	Number of Receiver Not Ready Packets sent.
CTR wfLapbPktStatsRrRxs	1.3.6.1.4.1.18.3.5.9.4.6.1.28	Counter	read-only	Number of Receiver Ready Packets received.
CTR wfLapbPktStatsRrTxs	1.3.6.1.4.1.18.3.5.9.4.6.1.17	Counter	read-only	Number of Receiver Ready Packets sent.
CTR wfLapbPktStatsSegmentRxs	1.3.6.1.4.1.18.3.5.9.4.6.1.33	Counter	read-only	Number of Charge Units received.
CTR wfLapbPktStatsSegmentTxs	1.3.6.1.4.1.18.3.5.9.4.6.1.22	Counter	read-only	Number of Charge Units sent.
INT wfLapbPktStatsSlotNum	1.3.6.1.4.1.18.3.5.9.4.6.1.1	INTEGER	read-only	Slot number and instance ID for this Lapb Packet Layer Line instance.
wfLapbPktStatsTable	1.3.6.1.4.1.18.3.5.9.4.6		not-accessible	The table of LAPB PKT Level Statistics.
CTR wfLapbPktStatsTotalConnections	1.3.6.1.4.1.18.3.5.9.4.6.1.10	Counter	read-only	Number of Total Virtual Connections performed since start up.
INT wfLapbPktT1	1.3.6.1.4.1.18.3.5.9.4.5.1.32	INTEGER	read-write	Local confirmation timeouts in seconds. This timer represents the following CCITT timers. If DCE: T10 (restart), T12 (reset), T13 (clear) If DTE: T20 (restart), T22 (reset), T23 (clear)
INT wfLapbPktT2	1.3.6.1.4.1.18.3.5.9.4.5.1.33	INTEGER	read-write	Call confirmation time out in seconds. This represent the CCITT T11 timer for the DCE and T21 timer for the DTE.
INT wfLapbPktT3	1.3.6.1.4.1.18.3.5.9.4.5.1.34	INTEGER	read-write	Congestion or busy condition watchdog timer in milliseconds. When system resources needed for packet assembly/deassembly depleted, this timer is set to reenter the PLP state machine to retry. User should use extreme caution in manipulating this timer.
INT wfLapbPktT4	1.3.6.1.4.1.18.3.5.9.4.5.1.35	INTEGER	read-write	Data packet transmission watchdog timer in milliseconds. This is the delay for acknowledgement. It is used to reenter PLP state machine also. User should use extreme caution in manipulating this timer.
wfLapbPktTable	1.3.6.1.4.1.18.3.5.9.4.5		not-accessible	The table of LAPB PKT Level Parameters
INT wfLapbPktThroughput	1.3.6.1.4.1.18.3.5.9.4.5.1.15	INTEGER	read-write	Throughput class negotiation facility subscription
INT wfLapbPktTransitDelay	1.3.6.1.4.1.18.3.5.9.4.5.1.28	INTEGER	read-write	Transit delay indication facility. If set, accept calls with this facility.
INT wfLapbPktTranspacCauseCodeEnable	1.3.6.1.4.1.18.3.5.9.4.5.1.59	INTEGER	read-write	Use Transpac Cause Codes , default = disabled.
INT wfLapbPktTxMbsQueueThreshold	1.3.6.1.4.1.18.3.5.9.4.5.1.60	INTEGER	read-write	The maximum number of packets that TX mbs queue can hold. If X.25 receives more packets and TX mbs queue count reaches this maximum, it will open up another SVC connection. The default is zero and the maximum queue count is equal to wfLapbPktDefWindow + 1, which is three.
INT wfLapbPktTxT5	1.3.6.1.4.1.18.3.5.9.4.5.1.53	INTEGER	read-write	Tx window size transmit delay timer
INT wfLapbPktUseDfltService	1.3.6.1.4.1.18.3.5.9.4.5.1.54	INTEGER	read-write	Indicates whether or not to use the default ddn service.
INT wfLapbPktUserIdentity	1.3.6.1.4.1.18.3.5.9.4.5.1.16	INTEGER	read-write	Network user identification (NUI) related facility subscription
wfX25	1.3.6.1.4.1.18.3.5.9.4.1
INT wfX25BackupInitiation	1.3.6.1.4.1.18.3.5.9.4.2.1.53	INTEGER	read-write	Determines whether to initiate PDN backup on failure of any SVC or the last one
INT wfX25Connector	1.3.6.1.4.1.18.3.5.9.4.7.1.4	INTEGER	read-only	Part of the Instance Identifier. This is the physical connector number for the physical layer associated with this packet layer
INT wfX25Delete	1.3.6.1.4.1.18.3.5.9.4.1.1	INTEGER	read-write	Create/Delete parameter. Default is created.
INT wfX25Disable	1.3.6.1.4.1.18.3.5.9.4.1.2	INTEGER	read-write	Enable/Disable parameter. Default is enabled.
INT wfX25LineNumber	1.3.6.1.4.1.18.3.5.9.4.7.1.5	INTEGER	read-only	Part of the Instance Id. This is the line number assigned to the LAPB driver associated with the X25 Packet layer.
INT wfX25LLIndex	1.3.6.1.4.1.18.3.5.9.4.7.1.6	INTEGER	read-only	Instance identifier. This is the lower layer index presented to X25 by the layer immediately below it on the protocol stack. If the lower layer is a driver, the index will be 0. Not used in 7.60.
INT wfX25PvcDelete	1.3.6.1.4.1.18.3.5.9.4.7.1.1	INTEGER	read-write	Create/Delete parameter, Default is created
INT wfX25PvcDisable	1.3.6.1.4.1.18.3.5.9.4.7.1.2	INTEGER	read-write	Enable/Disable Parameter
INT wfX25PvcRxDefClass	1.3.6.1.4.1.18.3.5.9.4.7.1.14	INTEGER	read-write	This is the receive througput class value that can be used on a per pvc basis. For this to be effective, the wfX25Throughput must be set ON
INT wfX25PvcRxDefLength	1.3.6.1.4.1.18.3.5.9.4.7.1.12	INTEGER	read-write	This is the receive packet size.
INT wfX25PvcRxDefWindow	1.3.6.1.4.1.18.3.5.9.4.7.1.10	INTEGER	read-write	This is the receive window size used for setting up the pvc.
INT wfX25PvcServiceCct	1.3.6.1.4.1.18.3.5.9.4.7.1.7	INTEGER	read-only	Instance Id. This is the Circuit number
wfX25PvcServiceEntry	1.3.6.1.4.1.18.3.5.9.4.7.1		not-accessible	An entry in the LAPB PKT table
INT wfX25PvcServiceIndex	1.3.6.1.4.1.18.3.5.9.4.7.1.8	INTEGER	read-only	Instace Id. This is the lcn on which this pvc is running
wfX25PvcServiceTable	1.3.6.1.4.1.18.3.5.9.4.7		not-accessible	the table of Lapb Pvc Packet level parameters
INT wfX25PvcServiceType	1.3.6.1.4.1.18.3.5.9.4.7.1.9	INTEGER	read-write	Type of Service for this PVC Service record
INT wfX25PvcTxDefClass	1.3.6.1.4.1.18.3.5.9.4.7.1.15	INTEGER	read-write	This is the transmit througput class value that can be used on a per pvc basis. For this to be effective, the wfX25Throughput must be set ON
INT wfX25PvcTxDefLength	1.3.6.1.4.1.18.3.5.9.4.7.1.13	INTEGER	read-write	This is the trasmit packet size
INT wfX25PvcTxDefWindow	1.3.6.1.4.1.18.3.5.9.4.7.1.11	INTEGER	read-write	This is the transmit window size used for setting up the pvc.
OCT wfX25QllcAddrMapAdjacentMac	1.3.6.1.4.1.18.3.5.9.4.8.1.11	OCTET STRING	read-write	The LLC MAC address of a LLC device emulated by this interface. If set to nil, a LLC MAC address will be dynamically assign by X.25 from an address pool defined in the X.25 Service Record.
INT wfX25QllcAddrMapAdjacentSap	1.3.6.1.4.1.18.3.5.9.4.8.1.12	INTEGER	read-write	The SAP of a LLC device emulated by this interface.
STR wfX25QllcAddrMapAdjacentX121	1.3.6.1.4.1.18.3.5.9.4.8.1.7	DisplayString	read-write	The X.121 address of a X.25 device connecting thru this interface. This address may contain wildcard characters.
INT wfX25QllcAddrMapCct	1.3.6.1.4.1.18.3.5.9.4.8.1.4	INTEGER	read-only	Circuit number and instance ID member.
INT wfX25QllcAddrMapDelete	1.3.6.1.4.1.18.3.5.9.4.8.1.1	INTEGER	read-write	Create/Delete parameter.
INT wfX25QllcAddrMapDisable	1.3.6.1.4.1.18.3.5.9.4.8.1.2	INTEGER	read-write	Enable/Disable parameter.
wfX25QllcAddrMapEntry	1.3.6.1.4.1.18.3.5.9.4.8.1		not-accessible	An entry in the QLLC Address Mapping table
INT wfX25QllcAddrMapGenXid	1.3.6.1.4.1.18.3.5.9.4.8.1.16	INTEGER	read-write	Simulate receiving an XID command from the QLLC device. This object should be enabled when an PU 2.0 QLLC device is connecting thru DLSw to an non-X.25 host.
INT wfX25QllcAddrMapIndex	1.3.6.1.4.1.18.3.5.9.4.8.1.5	INTEGER	read-only	X.25 QLLC Address Map entry record ID for this instance.
STR wfX25QllcAddrMapName	1.3.6.1.4.1.18.3.5.9.4.8.1.18	DisplayString	read-write	A informational name for this QLLC Mapping.
OCT wfX25QllcAddrMapNodeId	1.3.6.1.4.1.18.3.5.9.4.8.1.17	OCTET STRING	read-write	The 8 hexadecimal digit Node Identification field of the simulated XID (see wfX25QllcAddrMapGenXid object). This field has two sub-fields, ID Block and ID Number. The first 3 hexadecimal digits are the ID block value and the last 5 hexadecimal digits are the ID Number value.
INT wfX25QllcAddrMapOptions	1.3.6.1.4.1.18.3.5.9.4.8.1.13	INTEGER	read-write	This object is a bitmask, setting individual bit postions enable the option. Values may be added together to enable multiple options. Hex Dec Value Value Options --------------------------------------------------------- 0x0001 1 Do not wait for Adjacent DTE/DCE to send an QXID before forwarding an QXID to it. 0x0002 2 Enable when SDLC endstations are connecting to QLLC hosts that do not support receipt of XID polls and do not retransmit XIDs. 0x0004 4 wfX25QllcAddrMapPartnerMac field contains wildcard characters.
OCT wfX25QllcAddrMapPartnerMac	1.3.6.1.4.1.18.3.5.9.4.8.1.9	OCTET STRING	read-write	The LLC MAC address of a LLC device connecting thru this interface. The LLC MAC address may contain wildcard characters, see wfX25QllcAddrMapOptions attribute below.
INT wfX25QllcAddrMapPartnerSap	1.3.6.1.4.1.18.3.5.9.4.8.1.10	INTEGER	read-write	The SAP of a LLC device connecting thru this interface.
STR wfX25QllcAddrMapPartnerX121	1.3.6.1.4.1.18.3.5.9.4.8.1.6	DisplayString	read-write	The X.121 address of a X.25 device emulated by this interface.
INT wfX25QllcAddrMapPid	1.3.6.1.4.1.18.3.5.9.4.8.1.8	INTEGER	read-write	QLLC Protocol ID used in the first byte of Call User Data of the X.25 Call Request packet.
INT wfX25QllcAddrMapPuType	1.3.6.1.4.1.18.3.5.9.4.8.1.15	INTEGER	read-write	PU type (T2.0 or T2.1) of the locally attached QLLC device.
INT wfX25QllcAddrMapState	1.3.6.1.4.1.18.3.5.9.4.8.1.3	INTEGER	read-only	The current state of the QLLC Mapping.
wfX25QllcAddrMapTable	1.3.6.1.4.1.18.3.5.9.4.8		not-accessible	table of X.121 address to LLC Mac address mappings.
INT wfX25QllcAddrMapTrace	1.3.6.1.4.1.18.3.5.9.4.8.1.14	INTEGER	read-write	This object is a bitmask, setting individual bit postions enable logging of internal QLLC messages and events. Values may be added together to enable multiple message groups. Hex Dec Value Value Message/Event --------------------------------------------------------- 0x0001 1 Enable QLLC logging. 0x0002 2 Data frames/packets. 0x0004 4 Flow Control messages. 0x0008 8 Client registration messages. 0x0010 16 X.25 session establishment messages. 0x0020 32 Test frames/packets. 0x0040 64 XID frames/packes. 0x0080 128 Set Mode frames/packets. 0x0100 256 Disconnect frames/packets. 0x0200 512 Configuration changes. 0x0400 1024 Death of client (DLSw or APPN). 0x0800 2048 Data Path (DP) messages.
INT wfX25ServiceBackupRecoveryDelay	1.3.6.1.4.1.18.3.5.9.4.2.1.50	INTEGER	read-write	Delay in reverting back to a restored PDN service
INT wfX25ServiceBCast	1.3.6.1.4.1.18.3.5.9.4.2.1.14	INTEGER	read-write	Broadcast recipient status for this table entry instance.
INT wfX25ServiceBFE	1.3.6.1.4.1.18.3.5.9.4.2.1.31	INTEGER	read-write	Enabled if DDNX.25/BFE enabled.
INT wfX25ServiceBurstThrPerVc	1.3.6.1.4.1.18.3.5.9.4.2.1.49	INTEGER	read-only	Burst Throughput per VC, dynamically computed as Burst Throughput confiogured for the service record divided by number of VCs for the service record in Data Transfer State.
INT wfX25ServiceCallRetry	1.3.6.1.4.1.18.3.5.9.4.2.1.18	INTEGER	read-write	Interval in seconds between Call Request to same the destination. Must be at least 2 times T11/T21 Timer for Packet Level.
INT wfX25ServiceCct	1.3.6.1.4.1.18.3.5.9.4.2.1.7	INTEGER	read-only	Circuit number and instance ID member.
INT wfX25ServiceConnector	1.3.6.1.4.1.18.3.5.9.4.2.1.4	INTEGER	read-only	Connector number and instance ID member.
INT wfX25ServiceConnId	1.3.6.1.4.1.18.3.5.9.4.2.1.11	INTEGER	read-write	Connection Id to be used in a PTOP Call request. For PDN this will be the starting number to be used as Connection Id in PDN.
INT wfX25ServiceConnRef	1.3.6.1.4.1.18.3.5.9.4.2.1.10	INTEGER	read-only	Use of Connection Reference Numbers in Call Request For PDN only, if ON then use wfX25ServiceConnId as starting reference number for PDN.
INT wfX25ServiceCugFormat	1.3.6.1.4.1.18.3.5.9.4.2.1.26	INTEGER	read-write	Closed User Group Facility Format.
INT wfX25ServiceCugNum	1.3.6.1.4.1.18.3.5.9.4.2.1.28	INTEGER	read-write	Closed User Group (CUG) number.
INT wfX25ServiceCugType	1.3.6.1.4.1.18.3.5.9.4.2.1.27	INTEGER	read-write	Closed User Group Facility Type: Normal CUG, Bilateral CUG, or Outgoing Access CUG.
INT wfX25ServiceDelete	1.3.6.1.4.1.18.3.5.9.4.2.1.1	INTEGER	read-write	Create/Delete parameter, default = created.
INT wfX25ServiceDisable	1.3.6.1.4.1.18.3.5.9.4.2.1.2	INTEGER	read-write	Enable/Disable parameter, default = enabled.
wfX25ServiceEntry	1.3.6.1.4.1.18.3.5.9.4.2.1		not-accessible	An entry in the X25 Service table.
STR wfX25ServiceEntryName	1.3.6.1.4.1.18.3.5.9.4.2.1.54	DisplayString	read-write	name of the sevice entry
INT wfX25ServiceFastSelAccept	1.3.6.1.4.1.18.3.5.9.4.2.1.23	INTEGER	read-write	Fast Select Accept Facility for this table entry instance.
INT wfX25ServiceFastSelRequest	1.3.6.1.4.1.18.3.5.9.4.2.1.22	INTEGER	read-write	Fast Select Request Facility for this table entry instance.
INT wfX25ServiceFlowFacility	1.3.6.1.4.1.18.3.5.9.4.2.1.19	INTEGER	read-write	Flow Control negotiation facility parameter for this instance.
INT wfX25ServiceForceCugZero	1.3.6.1.4.1.18.3.5.9.4.2.1.32	INTEGER	read-write	Force Closed User Group of Zero.
INT wfX25ServiceIndex	1.3.6.1.4.1.18.3.5.9.4.2.1.8	INTEGER	read-only	X.25 service entry record ID for this instance.
INT wfX25ServiceLineNumber	1.3.6.1.4.1.18.3.5.9.4.2.1.5	INTEGER	read-only	Instance identifier member. This is the line number assigned to the driver X.25 is running over. No used in 7.60.
INT wfX25ServiceLLIndex	1.3.6.1.4.1.18.3.5.9.4.2.1.6	INTEGER	read-only	Instance identifier member. This is the lower layer index presented to X25 by the layer immediately below it on the protocol stack. If the lower layer is a driver, the index will be 0. Not used in 7.60.
INT wfX25ServiceMacPoolSize	1.3.6.1.4.1.18.3.5.9.4.2.1.39	INTEGER	read-write	The size of MAC address pool
OCT wfX25ServiceMacPoolStart	1.3.6.1.4.1.18.3.5.9.4.2.1.38	OCTET STRING	read-write	Starting address of MAC address pool
INT wfX25ServiceMaxConn	1.3.6.1.4.1.18.3.5.9.4.2.1.15	INTEGER	read-write	Maximum connections per destination for this table entry instance.
INT wfX25ServiceMaxIdle	1.3.6.1.4.1.18.3.5.9.4.2.1.17	INTEGER	read-write	Maximum Idle Time in Minutes for this table entry instance. If 0 is entered the connection stays on forever.
INT wfX25ServiceMUX	1.3.6.1.4.1.18.3.5.9.4.2.1.34	INTEGER	read-write	Set to Enabled to perform 1356 Multiplexing of protocols in the same Vc
INT wfX25ServicePktSize	1.3.6.1.4.1.18.3.5.9.4.2.1.21	INTEGER	read-write	Packet size parameter for this table entry instance.
CTR wfX25ServicePlpPktDrops	1.3.6.1.4.1.18.3.5.9.4.2.1.48	Counter	read-only	Total Number of Packets Dropped by PLP for VCs of this service record.
INT wfX25ServicePrecedence	1.3.6.1.4.1.18.3.5.9.4.2.1.16	INTEGER	read-write	Precedence value for this table entry instance. DDN only.
INT wfX25ServicePtopCallRequest	1.3.6.1.4.1.18.3.5.9.4.2.1.35	INTEGER	read-write	Select which side of PTOP circuit initiates the connection. (default = highest X.121 address initiates the call)
INT wfX25ServicePvcLcn	1.3.6.1.4.1.18.3.5.9.4.2.1.37	INTEGER	read-write	PVC Logical Channel Number for this service record
IP wfX25ServiceRemoteIpAddr	1.3.6.1.4.1.18.3.5.9.4.2.1.13	IpAddress	read-write	Remote IP address for PDN and DDN only.
STR wfX25ServiceRemoteX121Addr	1.3.6.1.4.1.18.3.5.9.4.2.1.12	DisplayString	read-write	Remote X.121 address for this table entry instance.
INT wfX25ServiceRetryNumber	1.3.6.1.4.1.18.3.5.9.4.2.1.52	INTEGER	read-write	The number of times a PDN SVC setup will be attempted if no response is received from the peer
INT wfX25ServiceRevChAccept	1.3.6.1.4.1.18.3.5.9.4.2.1.25	INTEGER	read-write	Reverse charge Accept Facility for this table entry instance.
INT wfX25ServiceRevChRequest	1.3.6.1.4.1.18.3.5.9.4.2.1.24	INTEGER	read-write	Reverse Charge Request Facility for this table entry instance.
INT wfX25ServiceSetupTime	1.3.6.1.4.1.18.3.5.9.4.2.1.51	INTEGER	read-write	Total time allowed for setting up a PDN SVC before attempting a backup
INT wfX25ServiceSlot	1.3.6.1.4.1.18.3.5.9.4.2.1.3	INTEGER	read-only	Slot number and part of Instance Id.
wfX25ServiceTable	1.3.6.1.4.1.18.3.5.9.4.2		not-accessible	This table describes the services of a circuit on an X.25 line.
INT wfX25ServiceType	1.3.6.1.4.1.18.3.5.9.4.2.1.9	INTEGER	read-write	Type of Service.
OCT wfX25ServiceUserFacility	1.3.6.1.4.1.18.3.5.9.4.2.1.29	OCTET STRING	read-write	Additional User Supplied Facilities. Must be in Hexadecimal form.
INT wfX25ServiceValid	1.3.6.1.4.1.18.3.5.9.4.2.1.30	INTEGER	read-only	Validity of the record - updated by X.25.
CTR wfX25ServiceVcBurstQClippedPkts	1.3.6.1.4.1.18.3.5.9.4.2.1.44	Counter	read-only	Total Number of packets dropped for VCs of this service record due to lack of buffers in their respective Burst Queues.
INT wfX25ServiceVcBurstQDepth	1.3.6.1.4.1.18.3.5.9.4.2.1.42	INTEGER	read-write	Maximum number of buffers that can be held in the Burst Queue while the VC gate pends.
GAU wfX25ServiceVcBurstQHighWaterPkts	1.3.6.1.4.1.18.3.5.9.4.2.1.46	Gauge	read-only	The Highest Water Packet Mark of the Burst Queues of VCs of this service record.
CTR wfX25ServiceVcBurstQPktCnt	1.3.6.1.4.1.18.3.5.9.4.2.1.45	Counter	read-only	Total Number of packets stored in the Burst Queues of VCs of this service record between successive attempts to forward to the PLP layer.
INT wfX25ServiceVcBurstThroughput	1.3.6.1.4.1.18.3.5.9.4.2.1.41	INTEGER	read-write	Maximum number of bits of data allowed to be transmitted for this service record in one second. This value is divided equally amongst the VCs active for this service record at any given point in time. A value of 0 indicates Burst control is not to be applied. The default value is 0.
CTR wfX25ServiceVcPktDrops	1.3.6.1.4.1.18.3.5.9.4.2.1.47	Counter	read-only	Total Number of Packets Dropped for VCs of this service record at the VC level.
INT wfX25ServiceVcPriority	1.3.6.1.4.1.18.3.5.9.4.2.1.43	INTEGER	read-write	Priority of the VCs associated with this service record. This value is used to specify whether packets being transmitted for this VC will be given preference over those on another VC or not. In the range for this value, 1..9999, 1 signifies highest priority.
INT wfX25ServiceVcType	1.3.6.1.4.1.18.3.5.9.4.2.1.36	INTEGER	read-write	Determines whether this service record represents a Switch Virtual Circuit (SVC) or Permanent Virtual Circuit (PVC). (default = svc)
INT wfX25ServiceWcpEnable	1.3.6.1.4.1.18.3.5.9.4.2.1.33	INTEGER	read-write	Enable compression
INT wfX25ServiceWindowTimeout	1.3.6.1.4.1.18.3.5.9.4.2.1.40	INTEGER	read-write	Window Timeout to detect a dysfunctional VC.
INT wfX25ServiceWinSize	1.3.6.1.4.1.18.3.5.9.4.2.1.20	INTEGER	read-write	Packet window size parameter for this table entry instance.
INT wfX25SlotNum	1.3.6.1.4.1.18.3.5.9.4.7.1.3	INTEGER	read-only	Part of the Instance Identifier. This is the slot number where this X25 packet layer is running
INT wfX25State	1.3.6.1.4.1.18.3.5.9.4.1.3	INTEGER	read-only	The current state of the entire X.25.
CTR wfX25VcApPktsDropped	1.3.6.1.4.1.18.3.5.9.4.4.1.25	Counter	read-only	Number of Application/redirector Packets Droped
CTR wfX25VcBurstQClippedPkts	1.3.6.1.4.1.18.3.5.9.4.4.1.27	Counter	read-only	Number of packets dropped for this VC due to lack of buffers in the Burst Queue. Packets are only dropped when the value of the statistic wfX25VcBurstQPktCnt is equal to wfX25ServiceVcBurstQDepth.
GAU wfX25VcBurstQHighWaterPkts	1.3.6.1.4.1.18.3.5.9.4.4.1.29	Gauge	read-only	High Water Packet Mark for the Burst Queue of this VC.
CTR wfX25VcBurstQPktCnt	1.3.6.1.4.1.18.3.5.9.4.4.1.28	Counter	read-only	Number of packets stored for this VC in the Burst Queue between successive attempts to forward to the PLP layer. This statistic is indicative of the transient loading of buffering mechanism between the PLP layer and the upper layers. The maximum value that this statistic can reach is determined by the setting of wfX25ServiceVcMaxBufCnt. When the value of this statistic is equal to wfX25ServiceVcBurstQDepth, all subsequently arriving packets are dropped.
CTR wfX25VcBytesRxs	1.3.6.1.4.1.18.3.5.9.4.4.1.23	Counter	read-only	Number of Data Bytes received.
CTR wfX25VcBytesTxs	1.3.6.1.4.1.18.3.5.9.4.4.1.14	Counter	read-only	Number of Data Bytes sent.
INT wfX25VcCct	1.3.6.1.4.1.18.3.5.9.4.4.1.5	INTEGER	read-only	Instance ID and CCT supporting these VCs. User determines this CCT via log.
INT wfX25VcConnector	1.3.6.1.4.1.18.3.5.9.4.4.1.2	INTEGER	read-only	Instance ID and Connector number this VC is using
CTR wfX25VcDataRxs	1.3.6.1.4.1.18.3.5.9.4.4.1.16	Counter	read-only	Number of Data Packets received.
CTR wfX25VcDataTxs	1.3.6.1.4.1.18.3.5.9.4.4.1.7	Counter	read-only	Number of Data Packets sent.
wfX25VcEntry	1.3.6.1.4.1.18.3.5.9.4.4.1		not-accessible	An entry in the X.25 VC table.
CTR wfX25VcIntBytesRxs	1.3.6.1.4.1.18.3.5.9.4.4.1.24	Counter	read-only	Number of Interrupt Data Bytes received.
CTR wfX25VcIntBytesTxs	1.3.6.1.4.1.18.3.5.9.4.4.1.15	Counter	read-only	Number of Interrupt Data Bytes sent.
CTR wfX25VcInterruptRxs	1.3.6.1.4.1.18.3.5.9.4.4.1.17	Counter	read-only	Number of Interrupt Packets received.
CTR wfX25VcInterruptTxs	1.3.6.1.4.1.18.3.5.9.4.4.1.8	Counter	read-only	Number of Interrupt Packets sent.
INT wfX25VcLineNumber	1.3.6.1.4.1.18.3.5.9.4.4.1.3	INTEGER	read-only	Instance identifier member. This is the line number assigned to the driver X25 is running on top of and this VC is running on. No used in 7.60
INT wfX25VcLLIndex	1.3.6.1.4.1.18.3.5.9.4.4.1.4	INTEGER	read-only	Instance identifier member. This is the lower layer index presented to X25 by the layer immediately below it on the protocol stack. If the lower layer is a driver, the index will be 0. Not used in 7.60.
CTR wfX25VcMaxTx	1.3.6.1.4.1.18.3.5.9.4.4.1.35	Counter	read-only	Maximum Number of buffers that can be sent from the upper layer to the PLP layer at any one time without overflowing the local assembly/desasembly queue.
CTR wfX25VcMbsOutstanding	1.3.6.1.4.1.18.3.5.9.4.4.1.33	Counter	read-only	Number of packets sent to the PLP layer from the upper layer that have not yet been added to the local assembly/deassembly queue at the PLP layer. These packets will require additional processing at a later time. This value is set after the PLP layer has completed processing of the maximum allowable number of packets received from the upper layer.
CTR wfX25VcMbsOutstandingPostTx	1.3.6.1.4.1.18.3.5.9.4.4.1.34	Counter	read-only	Number of buffers sent to the PLP layer that have not yet been added to the local asembly/deassembly queue. This value is set after the PLP layer has completed transmission of the maximum allowable number of packets from the local assembly/ deassembly queue to the lower layer.
CTR wfX25VcMbsQueueCnt	1.3.6.1.4.1.18.3.5.9.4.4.1.36	Counter	read-only	Number of buffers sent to the PLP layer that are currently on the local assembly/deassembly queue at the PLP layer. This value is set after the PLP layer has completed processing of the maximum allowable number of packets received from the upper layer.
CTR wfX25VcMbsQueueCntPostTx	1.3.6.1.4.1.18.3.5.9.4.4.1.37	Counter	read-only	Number of buffers sent to the PLP layer that have not yet been added to the local assembly/deassembly queue. This value is set after the PLP layer has completed transmission of the maximum allowable number of packets from the local assembly/ deassembly queue to the lower layer.
INT wfX25VcNumber	1.3.6.1.4.1.18.3.5.9.4.4.1.6	INTEGER	read-only	Instance ID and VC number for this VC. This number corresponds to the LCN.
CTR wfX25VcPktDrops	1.3.6.1.4.1.18.3.5.9.4.4.1.31	Counter	read-only	Total Number of Packets Dropped on this VC. These drops are caused by insufficient resources being available to forward the packets to the PLP layer.
CTR wfX25VcPktsLargerThanBurstThrCnt	1.3.6.1.4.1.18.3.5.9.4.4.1.30	Counter	read-only	Total Number of Packets serviced on this VC which are larger than the computed burst throughput per VC. The burst throughput per VC is computed as wfX25ServiceVcBurstThroughput / No. of Active VCs for the service record.
CTR wfX25VcPlpPktDrops	1.3.6.1.4.1.18.3.5.9.4.4.1.32	Counter	read-only	Total Number of Packets Dropped by PLP on this VC. These drops are due to either the line being disabled or the lack of buffering to store packets for transmission.
CTR wfX25VcRejectRxs	1.3.6.1.4.1.18.3.5.9.4.4.1.21	Counter	read-only	Number of Reject Packets received.
CTR wfX25VcRejectTxs	1.3.6.1.4.1.18.3.5.9.4.4.1.12	Counter	read-only	Number of Reject Packets sent.
STR wfX25VcRemoteX121Addr	1.3.6.1.4.1.18.3.5.9.4.4.1.26	DisplayString	read-only	Remote DTE Address for this connection
CTR wfX25VcResetRxs	1.3.6.1.4.1.18.3.5.9.4.4.1.18	Counter	read-only	Number of Reset Packets received.
CTR wfX25VcResetTxs	1.3.6.1.4.1.18.3.5.9.4.4.1.9	Counter	read-only	Number of Reset Packets sent.
CTR wfX25VcRnrRxs	1.3.6.1.4.1.18.3.5.9.4.4.1.20	Counter	read-only	Number of Receiver Not Ready Packets received.
CTR wfX25VcRnrTxs	1.3.6.1.4.1.18.3.5.9.4.4.1.11	Counter	read-only	Number of Receiver Not Ready Packets sent.
CTR wfX25VcRrRxs	1.3.6.1.4.1.18.3.5.9.4.4.1.19	Counter	read-only	Number of Receiver Ready Packets received.
CTR wfX25VcRrTxs	1.3.6.1.4.1.18.3.5.9.4.4.1.10	Counter	read-only	Number of Receiver Ready Packets sent.
CTR wfX25VcSegmentRxs	1.3.6.1.4.1.18.3.5.9.4.4.1.22	Counter	read-only	Number of Charge Units received.
CTR wfX25VcSegmentTxs	1.3.6.1.4.1.18.3.5.9.4.4.1.13	Counter	read-only	Number of Charge Units sent.
INT wfX25VcSlotNum	1.3.6.1.4.1.18.3.5.9.4.4.1.1	INTEGER	read-only	Instance ID and Slot number this VC is on.
wfX25VcTable	1.3.6.1.4.1.18.3.5.9.4.4		not-accessible	This is a table of Statistic Entries is per Virtual Circuit.
CTR wfX25VcTxQueueCnt	1.3.6.1.4.1.18.3.5.9.4.4.1.38	Counter	read-only	Number of buffers sent to the PLP layer that are currently on the transmit queue at the PLP layer. This value is set after the PLP layer has completed processing of the maximum allowable number of packets received from upper layer.
CTR wfX25VcTxQueueCntPostTx	1.3.6.1.4.1.18.3.5.9.4.4.1.39	Counter	read-only	Number of buffers sent to the PLP layer that are currently on thequeue to transmit at the PLP layer. This value is set after the PLP layer has completed transmission of the maximum allowable number of packets from the local assembly/deassembly queue to the lower layer.

RFC description

Vendor-specific MIB for Wellfleet Communications X.25 protocol management; monitors X.25 interface status, statistics, and configuration for WAN connectivity.

Start monitoring Wellfleet/Bay Networks/Nortel routers with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-X25-MIB

What Is Wellfleet-X25-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description