| OID symbolic | OID numeric | Type | Access | Description |
|---|
| wfWepLineTable | 1.3.6.1.4.1.18.3.4.28.1 | | not-accessible | The line table contains line entries. |
| wfWepLineEntry | 1.3.6.1.4.1.18.3.4.28.1.1 | | not-accessible | A line entry corresponds to a sync line. |
| INT wfWepLineDelete | 1.3.6.1.4.1.18.3.4.28.1.1.1 | INTEGER | read-write | Indicates whether the instance has been created or deleted. |
| INT wfWepLineDisable | 1.3.6.1.4.1.18.3.4.28.1.1.2 | INTEGER | read-only | Indicates whether the instance has been enabled or disabled. |
| INT wfWepLineLineNumber | 1.3.6.1.4.1.18.3.4.28.1.1.3 | INTEGER | read-only | Indicates the line number of this line entry. This is part
of the instance ID. |
| INT wfWepLineLLIndex | 1.3.6.1.4.1.18.3.4.28.1.1.4 | INTEGER | read-only | Indicates the lower layer index of this line entry. This
is part of the instance ID. |
| INT wfWepLineCipherMode | 1.3.6.1.4.1.18.3.4.28.1.1.5 | INTEGER | read-only | Indicates the encryption mode. This is represented by
the following 'bit mask' values:
DES 40-bit keys 0x20000000
DES 56-bit keys 0x10000000 |
| INT wfWepLineTekChangeByte | 1.3.6.1.4.1.18.3.4.28.1.1.6 | INTEGER | read-only | Frequency of traffic encryption key change, based upon number
of bytes encrypted; in operation, this is effectively rounded
up to the next full packet. Note that the key change rate is
also influenced by time. The so-called 'best' value will be
dependent upon the algorithms that use the TEK; also, for a
given algorithm the 'best' value will change over time due to
the progresses made in cryptanalysis. The strongest value
of this or the corresponding circuit setting will be used. |
| INT wfWepLineTekChangeTime | 1.3.6.1.4.1.18.3.4.28.1.1.7 | INTEGER | read-only | Frequency of traffic encryption key change, based upon number
of seconds elapsed since last key change; in operation, this
is effectively rounded up to the next full packet. Note that
the key change rate is also influenced by number of bytes
encrypted. The so-called 'best' value will be dependent upon
the algorithms that use the TEK; also, for a given algorithm
the 'best' value will change over time due to the progresses
made in cryptanalysis. The strongest value of this or the
corresponding circuit setting will be used. Units are seconds. |
| wfWepCircuitTable | 1.3.6.1.4.1.18.3.4.28.2 | | not-accessible | The circuit table contains circuit entries. |
| wfWepCircuitEntry | 1.3.6.1.4.1.18.3.4.28.2.1 | | not-accessible | A circuit entry corresponds to a circuit. |
| INT wfWepCircuitDelete | 1.3.6.1.4.1.18.3.4.28.2.1.1 | INTEGER | read-write | Indicates whether the instance has been created or deleted. |
| INT wfWepCircuitDisable | 1.3.6.1.4.1.18.3.4.28.2.1.2 | INTEGER | read-only | Indicates whether the instance has been enabled or disabled. |
| INT wfWepCircuitId | 1.3.6.1.4.1.18.3.4.28.2.1.3 | INTEGER | read-only | Indicates the circuit ID of this entry. |
| INT wfWepCircuitCipherMode | 1.3.6.1.4.1.18.3.4.28.2.1.4 | INTEGER | read-only | Indicates the encryption mode. This is represented by
the following 'bit mask' values:
Inherit from line 0x40000000
DES 40-bit keys 0x20000000
DES 56-bit keys 0x10000000 |
| INT wfWepCircuitTekChangeByte | 1.3.6.1.4.1.18.3.4.28.2.1.5 | INTEGER | read-only | Frequency of traffic encryption key change, based upon number
of bytes encrypted; in operation, this is effectively rounded
up to the next full packet. Note that the key change rate is
also influenced by time. The so-called 'best' value will be
dependent upon the algorithms that use the TEK; also, for a
given algorithm the 'best' value will change over time due to
the progresses made in cryptanalysis. The strongest value
of this or the corresponding line setting will be used. |
| INT wfWepCircuitTekChangeTime | 1.3.6.1.4.1.18.3.4.28.2.1.6 | INTEGER | read-only | Frequency of traffic encryption key change, based upon number
of seconds elapsed since last key change; in operation, this
is effectively rounded up to the next full packet. Note that
the key change rate is also influenced by number of bytes
encrypted. The so-called 'best' value will be dependent upon
the algorithms that use the TEK; also, for a given algorithm
the 'best' value will change over time due to the progresses
made in cryptanalysis. The strongest value of this or the
corresponding line setting will be used. Units are seconds. |
| wfWepVcTable | 1.3.6.1.4.1.18.3.4.28.3 | | not-accessible | The VC table contains VC entries |
| wfWepVcEntry | 1.3.6.1.4.1.18.3.4.28.3.1 | | not-accessible | A VC entry corresponds to a logical connection of the WEP. |
| INT wfWepVcLineNumber | 1.3.6.1.4.1.18.3.4.28.3.1.1 | INTEGER | read-only | Indicates the line number of this VC entry. This is part of
the instance ID. |
| INT wfWepVcLLIndex | 1.3.6.1.4.1.18.3.4.28.3.1.2 | INTEGER | read-only | Indicates the lower layer index of this VC entry. This is
part of the instance ID. |
| INT wfWepVcCircuitId | 1.3.6.1.4.1.18.3.4.28.3.1.3 | INTEGER | read-only | Indicates the circuit ID of this VC entry. This is part of
the instance ID. |
| INT wfWepVcId | 1.3.6.1.4.1.18.3.4.28.3.1.4 | INTEGER | read-only | Indicates the ID of this VC entry. This is part of the
instance ID. |
| INT wfWepVcConnectionState | 1.3.6.1.4.1.18.3.4.28.3.1.5 | INTEGER | read-only | Indicates the VC state of the WEP logical connection. |
| INT wfWepVcCipherMode | 1.3.6.1.4.1.18.3.4.28.3.1.6 | INTEGER | read-only | Indicates the encryption mode. This is only valid in
the 'up' state. The values are:
No algorithm yet 1
DES 40-bit keys 2
DES 56-bit keys 3 |
| INT wfWepVcTekChangeByte | 1.3.6.1.4.1.18.3.4.28.3.1.7 | INTEGER | read-only | Frequency of traffic encryption key change, based upon number
of bytes encrypted; in operation, this is effectively rounded
up to the next full packet. Note that the key change rate is
also influenced by time. The so-called 'best' value will be
dependent upon the algorithms that use the TEK; also, for a
given algorithm the 'best' value will change over time due to
the progresses made in cryptanalysis. This is the value used,
which is the strongest value of the corresponding line or
circuit setting. |
| INT wfWepVcTekChangeTime | 1.3.6.1.4.1.18.3.4.28.3.1.8 | INTEGER | read-only | Frequency of traffic encryption key change, based upon number
of bytes encrypted; in operation, this is effectively rounded
up to the next full packet. Note that the key change rate is
also influenced by time. The so-called 'best' value will be
dependent upon the algorithms that use the TEK; also, for a
given algorithm the 'best' value will change over time due to
the progresses made in cryptanalysis. This is the value used,
in units of seconds, which is the strongest value of the
corresponding line or circuit setting. |
| CTR wfWepVcBadMACReceiveds | 1.3.6.1.4.1.18.3.4.28.3.1.9 | Counter | read-only | Indicates the number of received packets with an invalid MAC
value, following decryption. |
| CTR wfWepVcBadCipherReceiveds | 1.3.6.1.4.1.18.3.4.28.3.1.10 | Counter | read-only | Indicates the number of received packets that failed
decryption. This class of error usually involves invalid
packet formats, etc. |
| CTR wfWepVcConnectionRetries | 1.3.6.1.4.1.18.3.4.28.3.1.11 | Counter | read-only | Indicates the number of timeouts which cause retransmission
of a connect request. This error means the router peer is
not responding. |
| CTR wfWepVcInvalidOpCodes | 1.3.6.1.4.1.18.3.4.28.3.1.12 | Counter | read-only | Indicates the number of supposed wep packets received with
bad op-codes. This class of error usually involves invalid
packet formats, etc. |
| CTR wfWepVcPacketsDroppedNotUp | 1.3.6.1.4.1.18.3.4.28.3.1.13 | Counter | read-only | Indicates the number of data packets dropped in the not-up
state. This error means the wep connection is not up yet for
some reason. |
| CTR wfWepVcPacketsDroppedBadN | 1.3.6.1.4.1.18.3.4.28.3.1.14 | Counter | read-only | Indicates the number of packets dropped for N-value mismatch.
This error means the router peers are not N-time-synchronized. |
| CTR wfWepVcPacketsDroppedAuthenticator | 1.3.6.1.4.1.18.3.4.28.3.1.15 | Counter | read-only | Indicates the number of control packets dropped for bad
authenticators. This class of error usually involves invalid
packet formats, etc. |
| CTR wfWepVcBadAlgorithmValueReceiveds | 1.3.6.1.4.1.18.3.4.28.3.1.16 | Counter | read-only | Indicates the number of control packets dropped for a bad
encryption algorithm value received. This class of error
usually involves invalid packet formats, etc. |
| CTR wfWepVcAlgorithmNoGCDs | 1.3.6.1.4.1.18.3.4.28.3.1.17 | Counter | read-only | Indicates the number of control packets dropped when there
is no encryption algorithm commonality between the 2 sides.
This would usually be due to not choosing any common
encryption algorithms for the two sides. |
| CTR wfWepVcAlgorithmMismatches | 1.3.6.1.4.1.18.3.4.28.3.1.18 | Counter | read-only | Indicates the number of control packets dropped because a
matching algorithm was arbitrated in one direction and then
a different algorithm was requested in the other direction.
However, both sides should be agreeing to the same algorithm
in both directions. This class of error usually involves
invalid packet formats, etc. |
| CTR wfWepVcUnexpectedState | 1.3.6.1.4.1.18.3.4.28.3.1.19 | Counter | read-only | Indicates internal errors for an unexpected state. |
| CTR wfWepVcPacketsDroppedBadMinorSeq | 1.3.6.1.4.1.18.3.4.28.3.1.20 | Counter | read-only | Indicates the number of data packets dropped for minor
sequence number mismatch. This error may indicate a replay
attack. |
| CTR wfWepVcEncryptedBytes | 1.3.6.1.4.1.18.3.4.28.3.1.21 | Counter | read-only | Indicates the number of bytes encrypted. |
| CTR wfWepVcDecryptedBytes | 1.3.6.1.4.1.18.3.4.28.3.1.22 | Counter | read-only | Indicates the number of bytes decrypted. |
| wfFrVCircuitLETable | 1.3.6.1.4.1.18.3.4.28.4 | | not-accessible | Frame Relay Circuit link encryption table gives attributs for the link
encryption for virtual circuits. |
| wfFrVCircuitLEEntry | 1.3.6.1.4.1.18.3.4.28.4.1 | | not-accessible | An entry in the Frame Relay Circuit table. An instance exists only if a
corresponding wfFrVCircuitEntry exists (e.g. for that same VC). |
| INT wfFrCircuitLEDelete | 1.3.6.1.4.1.18.3.4.28.4.1.1 | INTEGER | read-write | Create/delete parameter |
| INT wfFrCircuitLEDisable | 1.3.6.1.4.1.18.3.4.28.4.1.2 | INTEGER | read-only | Enable/disable link encryption on this VC |
| INT wfFrCircuitLELineNumber | 1.3.6.1.4.1.18.3.4.28.4.1.3 | INTEGER | read-only | Instance identifier. This is the line number on which the associated Frame
Relay interface resides. |
| INT wfFrCircuitLELLIndex | 1.3.6.1.4.1.18.3.4.28.4.1.4 | INTEGER | read-only | The Lower layer index uniquely identifies the lower layer in
cases where the lower layer may be something other than the
physical layer. For example if Frame Relay is running over
an ATM VC, the LLIndex identifies the ATM VC. |
| INT wfFrCircuitLECircuitNumber | 1.3.6.1.4.1.18.3.4.28.4.1.5 | INTEGER | read-only | The circuit number of this interface. |
| INT wfFrCircuitLEDlci | 1.3.6.1.4.1.18.3.4.28.4.1.6 | INTEGER | read-only | One of three instance identifier. This is the Frame Relay 'address'
of the virtual circuit. |
| INT wfFrCircuitLEState | 1.3.6.1.4.1.18.3.4.28.4.1.7 | INTEGER | read-only | Indicates the state of the particular virtual circuit. |
| OCT wfFrCircuitLELtsSecret | 1.3.6.1.4.1.18.3.4.28.4.1.8 | OCTET STRING | read-only | Long-term shared secret, used to generate a series
of key encryption keys for use during the connection.
This value contained in the MIB is itself encrypted
under the router's Node Protection Key, and includes
a cryptographic MAC to verify successful decryption. |
| INT wfFrCircuitLEMekChangeRate | 1.3.6.1.4.1.18.3.4.28.4.1.9 | INTEGER | read-only | The rate of change of the n counter in minutes, used in
generating the current master encryption key Kijn. |
| wfPppCircuitLETable | 1.3.6.1.4.1.18.3.4.28.5 | | not-accessible | The Wellfleet PPP Circuit Link Encryption Configuration Table contains
attributes for the link encryption mechanism. |
| wfPppCircuitLEEntry | 1.3.6.1.4.1.18.3.4.28.5.1 | | not-accessible | Per Wellfleet circuit PPP link encryption configuration parameters and
counters. An instance exists only if a corresponding wfPPPCircuitEntry
exists (e.g. for that same circuit). |
| INT wfPppCircuitLEDelete | 1.3.6.1.4.1.18.3.4.28.5.1.1 | INTEGER | read-write | Create/Delete parameter |
| INT wfPppCircuitLEDisable | 1.3.6.1.4.1.18.3.4.28.5.1.2 | INTEGER | read-only | Enable/disable link encryption on this circuit. |
| INT wfPppCircuitLEState | 1.3.6.1.4.1.18.3.4.28.5.1.3 | INTEGER | read-only | PPP link encryption state variable, Not Present, Init, Down, Up |
| INT wfPppCircuitLECircuitID | 1.3.6.1.4.1.18.3.4.28.5.1.4 | INTEGER | read-only | cct number for this instance |
| OCT wfPppCircuitLELtsSecret | 1.3.6.1.4.1.18.3.4.28.5.1.5 | OCTET STRING | read-only | Long-term shared secret, used to generate a series
of key encryption keys for use during the connection.
This value contained in the MIB is itself encrypted
under the router's Node Protection Key, and includes
a cryptographic MAC to verify successful decryption. |
| INT wfPppCircuitLEMekChangeRate | 1.3.6.1.4.1.18.3.4.28.5.1.6 | INTEGER | read-only | The rate of change of the n counter in minutes, used in
generating the current master encryption key Kijn. |
