Wellfleet-SWSMDS-MIB

All MIBs › Wellfleet-SWSMDS-MIB

Category: Wellfleet BayNetworks WAN Interfaces

Description: Manages Wellfleet switched SMDS service parameters and virtual circuit provisioning statistics.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is Wellfleet-SWSMDS-MIB?

The Wellfleet-SWSMDS-MIB is a proprietary Wellfleet Communications MIB for Switched Multi-megabit Data Service (SMDS), a legacy carrier WAN service supported on Wellfleet routers. It exposes configuration and provisioning data for SMDS virtual circuits along with per-circuit service parameters and statistics counters. Its principal monitoring value is tracking the operational and performance status of SMDS virtual circuits on a router's WAN interfaces, revealing service-level problems such as elevated error or discard counts, rather than general device hardware health. No dependency on other standard MIBs is apparent, as it sits entirely in Wellfleet's proprietary enterprise tree. It was used by carriers and enterprises running Wellfleet routers on SMDS-based WAN backbones, common before frame relay and ATM displaced SMDS. Engineers can download the Wellfleet-SWSMDS-MIB file directly to load it into their MIB browser.

IPNetwork Monitor allows you to monitor SNMP objects defined in Wellfleet-SWSMDS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Wellfleet router
Bay Networks/Nortel WAN router

Monitoring Examples

No specific object or table names were extracted for this module. Conceptually, an operator would use its per-VC provisioning and statistics objects to confirm an SMDS virtual circuit is correctly provisioned and to watch for elevated frame discard or error counts, which would indicate carrier-side congestion or a circuit misconfiguration. Because SMDS is now an obsolete technology, this MIB is mainly of legacy interest for maintaining older Wellfleet-based WAN links.

What Can Be Monitored

SMDS virtual circuit provisioning state
SMDS service parameters
per-circuit statistics counters
circuit error/discard counts

Imported Objects

From RFC-1212

OBJECT-TYPE

From RFC-1215

TRAP-TYPE

From RFC1155-SMI

Counter
Gauge
IpAddress
Opaque
TimeTicks
enterprises
mgmt

From RFC1213-MIB

DisplayString
mib-2

From Wellfleet-COMMON-MIB

wfSmdsSwGroup

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wfSmdsSwSubTable	1.3.6.1.4.1.18.3.5.9.7.1		not-accessible	The Wellfleet SMDS Switch Circuit (SNI, subscriber) Record. This record holds information on a per circuit (SSI, SNI, subscriber) basis.
wfSmdsSwSubEntry	1.3.6.1.4.1.18.3.5.9.7.1.1		not-accessible	Per Wellfleet circuit SMDS Switch configuration parameters and counters. This table contains Subscriber-Network Interface (SNI) parameters and state variables, one entry per SIP port.
INT wfSmdsSwSubDelete	1.3.6.1.4.1.18.3.5.9.7.1.1.1	INTEGER	read-write	create/delete parameter, dflt = created
INT wfSmdsSwSubDisable	1.3.6.1.4.1.18.3.5.9.7.1.1.2	INTEGER	read-write	enable/disable parameter, dflt = enabled
INT wfSmdsSwSubState	1.3.6.1.4.1.18.3.5.9.7.1.1.3	INTEGER	read-only	SMDS Switch state variable, Up, Down Init, Not Present
INT wfSmdsSwSubCct	1.3.6.1.4.1.18.3.5.9.7.1.1.4	INTEGER	read-only	cct number for this instance
INT wfSmdsSwSubDisableHrtbtPoll	1.3.6.1.4.1.18.3.5.9.7.1.1.5	INTEGER	read-write	determine use of DXI heartbeat poll
INT wfSmdsSwSubHrtbtPollAddr	1.3.6.1.4.1.18.3.5.9.7.1.1.6	INTEGER	read-write	determine if heartbeat poll messages are sent as as CPE or network (CSU/DSU) messages.
INT wfSmdsSwSubHrtbtPollInterval	1.3.6.1.4.1.18.3.5.9.7.1.1.7	INTEGER	read-write	heartbeat polling messages get sent every this many seconds - we don't want the polling interval to be less than or equal to the no-acknowledgment timer.
INT wfSmdsSwSubHrtbtPollDownCount	1.3.6.1.4.1.18.3.5.9.7.1.1.8	INTEGER	read-write	if this many consecutive heartbeat polling messages go unacknowledged, log an event declaring the line down
INT wfSmdsSwSubDisableNetMgmt	1.3.6.1.4.1.18.3.5.9.7.1.1.9	INTEGER	read-write	determine use of LMI network management
INT wfSmdsSwSubInterfaceType	1.3.6.1.4.1.18.3.5.9.7.1.1.10	INTEGER	read-write	defines whether this interface is a SNI or SSI.
INT wfSmdsSwSubInterfaceIndex	1.3.6.1.4.1.18.3.5.9.7.1.1.11	INTEGER	read-write	The index number for the SSI/SNI. Each SNI in the network has a unique id. The value of this object identifies the SIP port interface for which this entry contains management information.
INT wfSmdsSwSubDisableL3PduChecks	1.3.6.1.4.1.18.3.5.9.7.1.1.12	INTEGER	read-write	Enable/Disable L3_PDU verification. Default is disabled.
INT wfSmdsSwSubDisableUsageGeneration	1.3.6.1.4.1.18.3.5.9.7.1.1.13	INTEGER	read-write	enable/disable usage data generation. Default is disabled.
INT wfSmdsSwSubDisableMIR	1.3.6.1.4.1.18.3.5.9.7.1.1.14	INTEGER	read-write	enable/disable MIR enforcement, default is disabled.
CTR wfSmdsSwSubUnassignedSAs	1.3.6.1.4.1.18.3.5.9.7.1.1.15	Counter	read-only	The total number of SIP Level 3 PDUs discarded by the SMDS Switch because the Source Address was not assigned to the SNI.
CTR wfSmdsSwSubSAScreenViolations	1.3.6.1.4.1.18.3.5.9.7.1.1.16	Counter	read-only	The number of SIP L3_PDUs that violated the address screen based on source address screening for an SNI.
CTR wfSmdsSwSubDAScreenViolations	1.3.6.1.4.1.18.3.5.9.7.1.1.17	Counter	read-only	The total number of SIP Level 3 PDUs that violated the Destination Address Screening using either an Individual Address Screen or a Group Address Screen for the SNI.
CTR wfSmdsSwSubNumPDUExceededMIR	1.3.6.1.4.1.18.3.5.9.7.1.1.18	Counter	read-only	The total number of SIP L3_PDUs that exceeded the MIR on this interface.
CTR wfSmdsSwSubSipL3ReceivedIAs	1.3.6.1.4.1.18.3.5.9.7.1.1.19	Counter	read-only	The total number of individually addressed SIP Level 3 PDUs received by the SMDS Switch from the CPE. The total includes only unerrored L3PDUs.
CTR wfSmdsSwSubSipL3ReceivedGAs	1.3.6.1.4.1.18.3.5.9.7.1.1.20	Counter	read-only	The total number of group addressed SIP Level 3 PDUs received by the SMDS Switch from the CPE. The total includes only unerrored L3PDUs.
CTR wfSmdsSwSubSipL3UnrecIAs	1.3.6.1.4.1.18.3.5.9.7.1.1.21	Counter	read-only	The number of SIP Level 3 PDUs received by the SMDS Switch from the CPE that have an unknown, valid, individual SMDS Destination Address.
CTR wfSmdsSwSubSipL3UnrecGAs	1.3.6.1.4.1.18.3.5.9.7.1.1.22	Counter	read-only	The number of SIP Level 3 PDUs received by the SMDS Switch from the CPE that have an unknown, valid, group SMDS Destination Address.
CTR wfSmdsSwSubSipL3SentIAs	1.3.6.1.4.1.18.3.5.9.7.1.1.23	Counter	read-only	The number of individually addressed SIP Level 3 PDUs that have been sent by this SMDS Switch to the CPE.
CTR wfSmdsSwSubSipL3SentGAs	1.3.6.1.4.1.18.3.5.9.7.1.1.24	Counter	read-only	The number of group addressed SIP L3PDUs that have been sent by this SMDS Switch to the CPE.
CTR wfSmdsSwSubSipL3Errors	1.3.6.1.4.1.18.3.5.9.7.1.1.25	Counter	read-only	The total number of SIP Level 3 PDUs received by the SMDS Switch from the CPE that were discovered to have protocol errors.
CTR wfSmdsSwSubSipL3InvAddrTypes	1.3.6.1.4.1.18.3.5.9.7.1.1.26	Counter	read-only	The total number of SIP Level 3 PDUs received by the SMDS Switch from the CPE that had a value in the Source or Destination Address type subfield other than group or individual. Or if the Source Address type subfield value indicates a group address.
INT wfSmdsSwSubSipL3VersionSupport	1.3.6.1.4.1.18.3.5.9.7.1.1.27	INTEGER	read-only	A value which indicates the version(s) of SIP that this SNI supports. The value is a sum. This sum initially takes the value zero. For each version, V, that this interface supports, 2 raised to (V - 1) is added to the sum. For example, a port supporting versions 1 and 2 would have a value of (2^(1-1)+2^(2-1))=3. The SipL3VersionSupport is effectively a bit mask with Version 1 equal to the least significant bit (LSB).
OCT wfSmdsSwSubSAScrnViolationOccur	1.3.6.1.4.1.18.3.5.9.7.1.1.28	OCTET STRING	read-only	A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded as a result of a Source Address violation.
OCT wfSmdsSwSubDAScrnViolationOccur	1.3.6.1.4.1.18.3.5.9.7.1.1.29	OCTET STRING	read-only	A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded as a result of a Destination Address violation.
OCT wfSmdsSwSubUnassignedSAOccur	1.3.6.1.4.1.18.3.5.9.7.1.1.30	OCTET STRING	read-only	A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded as a result of a unassigned Source Address.
OCT wfSmdsSwSubSAErrorOccur	1.3.6.1.4.1.18.3.5.9.7.1.1.31	OCTET STRING	read-only	A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of a Source Address Field Format error.
OCT wfSmdsSwSubDAErrorOccur	1.3.6.1.4.1.18.3.5.9.7.1.1.32	OCTET STRING	read-only	A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of a Destination Address Field Format error.
OCT wfSmdsSwSubInvalidBASizeOccur	1.3.6.1.4.1.18.3.5.9.7.1.1.33	OCTET STRING	read-only	A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of an invalid BASize field value.
OCT wfSmdsSwSubInvalidHELenOccur	1.3.6.1.4.1.18.3.5.9.7.1.1.34	OCTET STRING	read-only	A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of an invalid Header Extension Length Field value.
OCT wfSmdsSwSubInvalidHEVerOccur	1.3.6.1.4.1.18.3.5.9.7.1.1.35	OCTET STRING	read-only	A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of an invalid Header Extension Version element.
OCT wfSmdsSwSubInvalidHECarOccur	1.3.6.1.4.1.18.3.5.9.7.1.1.36	OCTET STRING	read-only	A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of an invalid Header Extension Carrier element.
OCT wfSmdsSwSubInvalidHEPadOccur	1.3.6.1.4.1.18.3.5.9.7.1.1.37	OCTET STRING	read-only	A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of an invalid Header Extension Pad element.
OCT wfSmdsSwSubBEtagOccur	1.3.6.1.4.1.18.3.5.9.7.1.1.38	OCTET STRING	read-only	A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of a Beginning-End Tag mismatch.
OCT wfSmdsSwSubBAsizeNELenOccur	1.3.6.1.4.1.18.3.5.9.7.1.1.39	OCTET STRING	read-only	A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because the BAsize and Length fields are not equal.
OCT wfSmdsSwSubIncorrectLenOccur	1.3.6.1.4.1.18.3.5.9.7.1.1.40	OCTET STRING	read-only	A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because of an incorrect length.
OCT wfSmdsSwSubExceededMIROccur	1.3.6.1.4.1.18.3.5.9.7.1.1.41	OCTET STRING	read-only	A string containing the SMDS Source Address, Destination Address, and Event time of the most recent occurance of an L3_PDU discarded because it exceeded the MIR.
INT wfSmdsSwSubInBandMgmtDisable	1.3.6.1.4.1.18.3.5.9.7.1.1.42	INTEGER	read-write	In-Band Management enable/disable parameter. This attribute indicates whether the local WSNI (only) is enabled to run IP in Host mode, for in-band management purposes, in additional to being a switch interface. The default is disabled
OCT wfSmdsSwSubInBandMgmtLocalAddr	1.3.6.1.4.1.18.3.5.9.7.1.1.43	OCTET STRING	read-write	Special SMDS E.164 Individual address that identifies this local circuit. This attribute is only used when the wfSmdsSwSubInBandMgmtDisable attribute is set to ENABLED
CTR wfSmdsSwSubInBandMgmtReceivedPDUs	1.3.6.1.4.1.18.3.5.9.7.1.1.44	Counter	read-only	The total number of individually addressed In-Band Management PDUs received by the SMDS Switch from the CPE. The total includes only unerrored PDUs.
CTR wfSmdsSwSubInBandMgmtSentPDUs	1.3.6.1.4.1.18.3.5.9.7.1.1.45	Counter	read-only	The number of individually addressed In-Band Management PDUs that have been sent by this SMDS Switch to the CPE.
CTR wfSmdsSwSubInBandMgmtMaxLenErrors	1.3.6.1.4.1.18.3.5.9.7.1.1.46	Counter	read-only	The number of In-Band Management PDUs that have exceeded the MTU size configured for the line
CTR wfSmdsSwSubInBandMgmtEncapsErrors	1.3.6.1.4.1.18.3.5.9.7.1.1.47	Counter	read-only	The number of In-Band Management PDUs that have invalid encapsulation schemes
CTR wfSmdsSwSubGAPartialResolve	1.3.6.1.4.1.18.3.5.9.7.1.1.48	Counter	read-only	The number of times group addressed L3_PDU's could not be resolved due to congestion.
CTR wfSmdsSwSubDANotOnSni	1.3.6.1.4.1.18.3.5.9.7.1.1.49	Counter	read-only	The number of times a L3_PDU was discarded at the egress because the destination address was not assigned to the SNI.
wfSmdsSwEndpTable	1.3.6.1.4.1.18.3.5.9.7.2		not-accessible	The Parameters for the Endpoint table. An Endpoint is defined as an IP address, SMDS E.164 address pair. Endpoint ranges should never overlap.
wfSmdsSwEndpEntry	1.3.6.1.4.1.18.3.5.9.7.2.1		not-accessible	The parameters for a particular Endpoint.
INT wfSmdsSwEndpDelete	1.3.6.1.4.1.18.3.5.9.7.2.1.1	INTEGER	read-write	Indication to delete this endpoint entry.
OCT wfSmdsSwEndpE164AddrHigh	1.3.6.1.4.1.18.3.5.9.7.2.1.2	OCTET STRING	read-only	The High end of the E.164 address range for this endpoint information.
OCT wfSmdsSwEndpE164AddrDelta	1.3.6.1.4.1.18.3.5.9.7.2.1.3	OCTET STRING	read-only	The difference between wfSmdsSwEndpE164AddrHigh to the beginning of the endpoint information.
INT wfSmdsSwEndpInterfaceIndex	1.3.6.1.4.1.18.3.5.9.7.2.1.4	INTEGER	read-only	This number indicates which SNI the endpoint information refers to.
wfSmdsSwInterfaceTable	1.3.6.1.4.1.18.3.5.9.7.3		not-accessible	This is the Interface Table. This table also holds the Maximum Information Rate (MIR) information.
wfSmdsSwInterfaceEntry	1.3.6.1.4.1.18.3.5.9.7.3.1		not-accessible	This table defines the IP addresses and what interfaces they are associated with.
INT wfSmdsSwInterfaceDelete	1.3.6.1.4.1.18.3.5.9.7.3.1.1	INTEGER	read-write	Indication to delete this interface entry.
INT wfSmdsSwInterfaceType	1.3.6.1.4.1.18.3.5.9.7.3.1.2	INTEGER	read-only	This number determines whether the interface information refers to an SNI, SSI, or ICI.
INT wfSmdsSwInterfaceIndex	1.3.6.1.4.1.18.3.5.9.7.3.1.3	INTEGER	read-only	This number indicates which SNI, SSI, or ICI the interface information refers to.
IP wfSmdsSwInterfaceIpAddr	1.3.6.1.4.1.18.3.5.9.7.3.1.4	IpAddress	read-write	IP Address associated with the interface.
INT wfSmdsSwInterfaceMIR	1.3.6.1.4.1.18.3.5.9.7.3.1.5	INTEGER	read-write	This number represents the MIR in octets per second.
INT wfSmdsSwInterfaceCurrentRate	1.3.6.1.4.1.18.3.5.9.7.3.1.6	INTEGER	read-only	This number indicates the current rate of traffic flow to the interface. The software updates this counter. When this attribute exceeds wfSmdsSwInterfaceMIR traffic to the interface is dropped. Periodically the sofware resets this counter to zero.
wfSmdsSwAssocScrnTable	1.3.6.1.4.1.18.3.5.9.7.4		not-accessible	This list identifies the associated SNI addresses per individualand group address screen. Different addresses on an SNI may be associated with different individual and group address screens (one individual address screen per associated address on an SNI, and one group address screen per associated address on an SNI ).
wfSmdsSwAssocScrnEntry	1.3.6.1.4.1.18.3.5.9.7.4.1		not-accessible	An SNI index, group and individual screening list index, and the associated addresses for the SNI for the address screens.
INT wfSmdsSwAssocScrnDelete	1.3.6.1.4.1.18.3.5.9.7.4.1.1	INTEGER	read-write	Indication to delete this associated screen entry.
INT wfSmdsSwAssocScrnSniIndex	1.3.6.1.4.1.18.3.5.9.7.4.1.2	INTEGER	read-only	The value of this object identifies the SIP Port interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex, defined in RFC1213, for the same interface.
OCT wfSmdsSwAssocScrnAddrInd	1.3.6.1.4.1.18.3.5.9.7.4.1.3	OCTET STRING	read-only	The value of this object identifies one of the SMDS addresses for the SNI, identified by the wfSmdsSwAssocScrnSniIndex that belongs to this individual (or group) address screen (wfSmdsSwAssocScrnAddrInd). This list will contain both individual and group addresses, because this list is used for both Destination Address Screening and Source Address Screening; the destination address in the L3_PDU that is undergoing Source Address Screening may be either a group or individual address that is assigned to that SNI. One screen will have a maximum of 64 associated addresses; up to a maximum of 16 individual addresses identifying an SNI and up to a maximum of 48 group addresses identifying an SNI.
INT wfSmdsSwAssocScrnIndivIndex	1.3.6.1.4.1.18.3.5.9.7.4.1.4	INTEGER	read-only	The value of this object identifies the individual address screening list. There is at least one individual address screen and at most s individual address screens per SNI. The initial value of s is defined to be 4. In the future more screening lists per SNI may be allowed. The values of this object correspond to the values of wfSmdsSwIAScrnIndex in the wfSmdsSwIAScrnTable.
INT wfSmdsSwAssocScrnGrpIndex	1.3.6.1.4.1.18.3.5.9.7.4.1.5	INTEGER	read-only	The value of this object identifies the group address screening list. There is at least one group address screen and at most s group address screens per SNI. The initial value of s is defined to be 4. In the future more screening lists per SNI may be allowed. The values of this object correspond to the values of wfSmdsSwGAScrnIndex in the wfSmdsSwGAScrnTable. This field applies only to individual addresses on the SNI because it applies only to destination address screening of group addresses.
wfSmdsSwIAScrnTable	1.3.6.1.4.1.18.3.5.9.7.5		not-accessible	This list identifies the individual addresses that will be screened per individual address screen table. The are up to s (s is equal to 4) individual address screens per SNI and at least one individual address screen per SNI. The Individual Address Screens and the Group Address Screens together consist of up to n addresses. The initial value of n is defined as 128. In the future a value of n up to 2048 may be supported. The Individual Address Screen is used to perform Destination Address Screening for individually addressed data units and Source Address Screening for all data units. The Group Address Screen is used to perform Destination Address Screening for group addressed data units.
wfSmdsSwIAScrnEntry	1.3.6.1.4.1.18.3.5.9.7.5.1		not-accessible	An SNI index, a screening list index, the individual addresses to be screened for the individual address screen, and whether the screened address is valid or invalid.
INT wfSmdsSwIAScrnDelete	1.3.6.1.4.1.18.3.5.9.7.5.1.1	INTEGER	read-write	Indication to delete this IA screen entry.
INT wfSmdsSwIAScrnSniIndex	1.3.6.1.4.1.18.3.5.9.7.5.1.2	INTEGER	read-only	The value of this object identifies the SIP Port interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex, defined in RFC1213, for the same interface.
INT wfSmdsSwIAScrnIndex	1.3.6.1.4.1.18.3.5.9.7.5.1.3	INTEGER	read-only	The value of this object identifies the individual address screening list. There are at least one individual address screen and at most s individual address screens per SNI. The initial value of s is defined to be 4. In the future more screening lists per SNI may be allowed. The values of this object correspond to the values of wfSmdsSwScrnIndex in the wfSmdsSwScrnTable.
OCT wfSmdsSwIAScrnAddr	1.3.6.1.4.1.18.3.5.9.7.5.1.4	OCTET STRING	read-only	The value of this object identifies one of the individual addresses to be screened for source and destination address screening for the SNI identified by the wfSmdsSwIAScrnSniIndex and for the particular individual address screen (wfSmdsSwIAScrnIndex).
wfSmdsSwGAScrnTable	1.3.6.1.4.1.18.3.5.9.7.6		not-accessible	This list identifies the group addresses that will be screened per group address screen table. The are up to s (s is equal to 4) group address screens per SNI and at least one group address screen per SNI. The Individual Address Screen and the Group Address Screen together consist of up to n addresses. The initial value of n is defined as 128. In the future a value of n up to 2048 may be supported. The Individual Address Screen is used to perform Destination Address Screening for individually addressed data units and Source Address Screening for all data units. The Group Address Screen is used to perform Destination Address Screening for group addressed data units.
wfSmdsSwGAScrnEntry	1.3.6.1.4.1.18.3.5.9.7.6.1		not-accessible	An SNI index, a screening list index, the group addresses to be screened for the group address screen, and whether the screened address is valid or invalid.
INT wfSmdsSwGAScrnDelete	1.3.6.1.4.1.18.3.5.9.7.6.1.1	INTEGER	read-write	Indication to delete this GA screen entry.
INT wfSmdsSwGAScrnSniIndex	1.3.6.1.4.1.18.3.5.9.7.6.1.2	INTEGER	read-only	The value of this object identifies the SIP Port interface for which this entry contains management information. The value of this object for a particular interface has the same value as the ifIndex, defined in RFC1213, for the same interface.
INT wfSmdsSwGAScrnIndex	1.3.6.1.4.1.18.3.5.9.7.6.1.3	INTEGER	read-only	The value of this object identifies the group address screening list. There is at least one group address screen and at most s group address screens per SNI. The initial value of s is defined to be 4. In the future more screening lists per SNI may be allowed. The values of this object correspond to the values of wfSmdsSwScrnIndex in the wfSmdsSwSmdsScrnTable.
OCT wfSmdsSwGAScrnAddr	1.3.6.1.4.1.18.3.5.9.7.6.1.4	OCTET STRING	read-only	The value of this object identifies one of the group addresses to be screened for destination address screening for the SNI identified by the wfSmdsSwGAScrnSniIndex and for the particular group address screen (wfSmdsSwGAScrnIndex).
wfSmdsSwGATable	1.3.6.1.4.1.18.3.5.9.7.7		not-accessible	A table of all group addresses in the network and the associated individual addresses identified by each group address. A group address identifies up to m individual addresses. An SMDS SS supports up to n group addresses. A group address can be identified by up to p individual addresses. A particular SNI is identified by up to 48 group addresses. The initial values of m, n, and p are defined as 128, 1024, and 32, respectively. In the future values of m and n of 2048 and 8192, respectively, may be supported.
wfSmdsSwGAEntry	1.3.6.1.4.1.18.3.5.9.7.7.1		not-accessible	A Group Address and an address in that group and whether that association is valid or invalid.
INT wfSmdsSwGADelete	1.3.6.1.4.1.18.3.5.9.7.7.1.1	INTEGER	read-write	Indication to delete this group address entry.
INT wfSmdsSwGASSI	1.3.6.1.4.1.18.3.5.9.7.7.1.2	INTEGER	read-only	The SSI associated with this Group Address. An SSI of 0 is used to indicate that all interfaces can use the group address. An SSI other than 0 indicates that only the SSI, or an SNI associated with the SSI should use the group.
OCT wfSmdsSwGAGroupAddress	1.3.6.1.4.1.18.3.5.9.7.7.1.3	OCTET STRING	read-only	A Group Address.
OCT wfSmdsSwGAGroupMember	1.3.6.1.4.1.18.3.5.9.7.7.1.4	OCTET STRING	read-only	An individual SMDS address that belongs to this Group Address.
wfSmdsSwCurUsageTable	1.3.6.1.4.1.18.3.5.9.7.8		not-accessible	This table contains the Current Usage Data. This is the interface between Billing and Switching. The Switch gates create these records. The Billing gates collect them to create billing data.
wfSmdsSwCurUsageEntry	1.3.6.1.4.1.18.3.5.9.7.8.1		not-accessible	The usage data for the current usage period indexed by destination,source address.
INT wfSmdsSwCurUsageDelete	1.3.6.1.4.1.18.3.5.9.7.8.1.1	INTEGER	read-write	Indication to delete this current usage entry.
INT wfSmdsSwCurUsageSni	1.3.6.1.4.1.18.3.5.9.7.8.1.2	INTEGER	read-only	The SNI number of the interface generating the usage information
OCT wfSmdsSwCurUsageDestAddr	1.3.6.1.4.1.18.3.5.9.7.8.1.3	OCTET STRING	read-only	The destination address of a SMDS group or individual E.164 address.
OCT wfSmdsSwCurUsageSrcAddr	1.3.6.1.4.1.18.3.5.9.7.8.1.4	OCTET STRING	read-only	The source address of a SMDS individual E.164 address.
OCT wfSmdsSwCurUsageGrpIndAddr	1.3.6.1.4.1.18.3.5.9.7.8.1.5	OCTET STRING	read-only	When the destination address of an L3_PDU is a group address, this attribute is set to one of the E.164 individual addresses that is in the group address and on the destination SNI.
CTR wfSmdsSwCurUsageNumL3Pdu	1.3.6.1.4.1.18.3.5.9.7.8.1.6	Counter	read-only	This number represents the number of billable L3_PDUs counted by the circuit during the most recent collection interval.
CTR wfSmdsSwCurUsageNumOctet	1.3.6.1.4.1.18.3.5.9.7.8.1.7	Counter	read-only	This number represents the number of billable octets counted by the circuit during the most recent collection interval.
INT wfSmdsSwCurUsageToBeDeleted	1.3.6.1.4.1.18.3.5.9.7.8.1.8	INTEGER	read-only	Indication to billing to delete this current usage entry.
wfSmdsSwUsage	1.3.6.1.4.1.18.3.5.9.7.9
INT wfSmdsSwUsageEnable	1.3.6.1.4.1.18.3.5.9.7.9.1	INTEGER	read-write	Enable/Disable SMDS_SW billing.
INT wfSmdsSwUsageVolume	1.3.6.1.4.1.18.3.5.9.7.9.2	INTEGER	read-write	Indicates the file system volume number to which the billing usage data files will be written. The volume number corresponds to the slot number on which the volume resides. Note: Value 0 has the special meaning that no 'Store' and 'Flush' operations will take place. This translates to no Billing data will be written to the local file system. 'Update' operations will still be performed on each local slot. Full Billing statistics will still be available in the wfSmdsSwUsageTable MIB.
INT wfSmdsSwUsageVolumeBackup	1.3.6.1.4.1.18.3.5.9.7.9.3	INTEGER	read-write	Indicates the backup volume if wfSmdsSwUsageVolume becomes inoperative. Note: This feature is not implemented in this release.
STR wfSmdsSwUsageDirectory	1.3.6.1.4.1.18.3.5.9.7.9.4	DisplayString	read-write	The name of the directory where the billing usage data files are stored.
STR wfSmdsSwUsageFilePrefix	1.3.6.1.4.1.18.3.5.9.7.9.5	DisplayString	read-write	The base name of billing usage data files.
INT wfSmdsSwUsageTimerInterval	1.3.6.1.4.1.18.3.5.9.7.9.6	INTEGER	read-write	This number determines the timer interval (number of seconds) unit for the Billing process to perform its various timer driven tasks. i.e. updating billing usage data, writing billing usage data to file system and file system management activities.
INT wfSmdsSwUsageUpdateInterval	1.3.6.1.4.1.18.3.5.9.7.9.7	INTEGER	read-write	This number specifies the interval (number of minutes) for the Billing process to collect and update billing usage data in the wfSmdsSwUsage MIB. Note: When converted to seconds, this must be a multiple of wfSmdsSwUsageTimerInterval.
INT wfSmdsSwUsageStoreInterval	1.3.6.1.4.1.18.3.5.9.7.9.8	INTEGER	read-write	This number specifies the interval (number of minutes) for the Billing process to write billing usage data on to the file system from the wfSmdsSwUsage MIB. Note: When converted to seconds, this must be a multiple of wfSmdsSwUsageTimerInterval.
INT wfSmdsSwUsageFlushInterval	1.3.6.1.4.1.18.3.5.9.7.9.9	INTEGER	read-write	This number specifies the interval (number of minutes) for the Billing process to write billing usage data on to the file system from the wfSmdsSwUsage MIB followed by zeroing the wfSmdsSwUsage MIB. Note: When converted to seconds, this must be a multiple of wfSmdsSwUsageTimerInterval.
INT wfSmdsSwUsageCleanupInterval	1.3.6.1.4.1.18.3.5.9.7.9.10	INTEGER	read-write	This is the interval (number of minutes) for the Billing process to check and delete old billing usage data files. Note: When converted to seconds, this must be a multilple of wfSmdsSwUsageTimerInterval.
INT wfSmdsSwUsageLocalTimeZone	1.3.6.1.4.1.18.3.5.9.7.9.11	INTEGER	read-only	Indicates local time zone of the switch
TIK wfSmdsSwUsageUpdateTimeStamp	1.3.6.1.4.1.18.3.5.9.7.9.12	TimeTicks	read-only	Time stamp of last wfSmdsSwUsageUpdateInterval timer expiration or the starting time of the current wfSmdsSwUsageUpdateInterval. This value is number of seconds since midnight Jan 1, 1976 (GMT).
TIK wfSmdsSwUsageStoreTimeStamp	1.3.6.1.4.1.18.3.5.9.7.9.13	TimeTicks	read-only	Time stamp of last wfSmdsSwUsageStoreInterval timer expiration or the starting time of the current wfSmdsSwUsageStoreInterval. This value is number of seconds since midnight Jan. 1, 1976 (GMT).
TIK wfSmdsSwUsageFlushTimeStamp	1.3.6.1.4.1.18.3.5.9.7.9.14	TimeTicks	read-only	Time stamp of last wfSmdsSwUsageFlushInterval timer expiration or the starting time of the current wfSmdsSwUsageFlushInterval. This value is number of seconds since midnight Jan. 1, 1976 (GMT).
TIK wfSmdsSwUsageCleanupTimeStamp	1.3.6.1.4.1.18.3.5.9.7.9.15	TimeTicks	read-only	Time stamp of last wfSmdsSwUsageCleanupInterval timer expiration or the starting time of the current wfSmdsSwUsageCleanupInterval. This value is number of seconds since midnight Jan. 1, 1976 (GMT).
INT wfSmdsSwUsageUpdateData	1.3.6.1.4.1.18.3.5.9.7.9.16	INTEGER	read-write	Setting this attribute to a non-zero value will cause an immediate updating of the billing usage data. Once activated, this attribute should be reset to zero to allow subsequent activations.
INT wfSmdsSwUsageStoreData	1.3.6.1.4.1.18.3.5.9.7.9.17	INTEGER	read-write	Setting this attribute to a non-zero value will cause an immediate updating and writing of the billing usage data. Once activated, this attribute should be reset to zero to allow subsequent activations.
INT wfSmdsSwUsageFlushData	1.3.6.1.4.1.18.3.5.9.7.9.18	INTEGER	read-write	Setting this attribute to a non-zero value will cause an immediate updating and writing of the billing usage data and followed by zeroing the wfSmdsSwBillingUsage MIB. Once activated, this attribute should be reset to zero to allow subsequent activations.
INT wfSmdsSwUsageFileCleanup	1.3.6.1.4.1.18.3.5.9.7.9.19	INTEGER	read-write	Setting this attribute to a non-zero value will cause an immediate checking and deleting old billing usage data files. Once activated, this attribute should be reset to zero to allow subsequent activations.
INT wfSmdsSwUsageState	1.3.6.1.4.1.18.3.5.9.7.9.20	INTEGER	read-only	current state of SMDS_SW billing.
INT wfSmdsSwUsageCurVolume	1.3.6.1.4.1.18.3.5.9.7.9.21	INTEGER	read-only	current file system volume number used. This number is the same as wfSmdsSwUsageVolume except when the user sets wfSmdsSwUsageVolume to an invalid number.
INT wfSmdsSwUsageCurVolumeBackup	1.3.6.1.4.1.18.3.5.9.7.9.22	INTEGER	read-only	curent backup file system volume number used. This number is the same as wfSmdsSwUsageVolumeBackUp except when the user sets wfSmdsSwUsageVolume to an invalid number. Note: This feature is not implemented in this release.
STR wfSmdsSwUsageCurDirectory	1.3.6.1.4.1.18.3.5.9.7.9.23	DisplayString	read-only	current directory name used. This number is the same as wfSmdsSwUsageDirectory except when the user sets wfSmdsSwUsageDirectory to an invalid name.
STR wfSmdsSwUsageCurFilePrefix	1.3.6.1.4.1.18.3.5.9.7.9.24	DisplayString	read-only	current base file name used. This number is the same as wfSmdsSwUsageFilePrefix except when the user sets wfSmdsSwUsageFilePrefix to an invalid name.
INT wfSmdsSwUsageCurTimerInterval	1.3.6.1.4.1.18.3.5.9.7.9.25	INTEGER	read-only	current timer interval number used. This number is the same as wfSmdsSwUsageTimerInterval except when the user sets wfSmdsSwUsageTimerInterval to an invalid value.
INT wfSmdsSwUsageCurUpdateInterval	1.3.6.1.4.1.18.3.5.9.7.9.26	INTEGER	read-only	current update interval number used. This number is the same as wfSmdsSwUsageUpdateInterval except when the user sets wfSmdsSwUsageUpdateInterval to an invalid value.
INT wfSmdsSwUsageCurStoreInterval	1.3.6.1.4.1.18.3.5.9.7.9.27	INTEGER	read-only	current store timer interval number used. This number is the same as wfSmdsSwUsageStoreInterval except when the user sets wfSmdsSwUsageStoreInterval to an invalid value.
INT wfSmdsSwUsageCurFlushInterval	1.3.6.1.4.1.18.3.5.9.7.9.28	INTEGER	read-only	current flush timer interval number used. This number is the same as wfSmdsSwUsageFlushInterval except when the user sets wfSmdsSwUsageFlushInterval to an invalid value.
INT wfSmdsSwUsageCurCleanupInterval	1.3.6.1.4.1.18.3.5.9.7.9.29	INTEGER	read-only	current file cleanup timer interval number used. This number is the same as wfSmdsSwUsageCleanupInterval except when the user sets wfSmdsSwUsageCleanupInterval to an invalid value.
INT wfSmdsSwUsageDebug	1.3.6.1.4.1.18.3.5.9.7.9.30	INTEGER	read-write	Enable/Disable printing of debug edl (trap) messages. NOTE: Do not enable this attribute in operational enviornment as it will likely flood the logging facility. This attribute is reserved for specialized debugging in a controlled lab enviornment.
INT wfSmdsSwUsageCurDebug	1.3.6.1.4.1.18.3.5.9.7.9.31	INTEGER	read-only	current debug value used. This value is the same as wfSmdsSwUsageDebug except when the user sets wfSmdsSwUsageDeubg to an invalid value.
INT wfSmdsSwUsageSwitchId	1.3.6.1.4.1.18.3.5.9.7.9.32	INTEGER	read-only	switch id used in the billing usage data file.
INT wfSmdsSwUsageNumEntries	1.3.6.1.4.1.18.3.5.9.7.9.33	INTEGER	read-only	number of entries in wfSmdsSwUsageTable
wfSmdsSwUsageTable	1.3.6.1.4.1.18.3.5.9.7.10		not-accessible	The Billing Usage Table.
wfSmdsSwUsageEntry	1.3.6.1.4.1.18.3.5.9.7.10.1		not-accessible	The parameters for Billing Usage.
INT wfSmdsSwUsageDelete	1.3.6.1.4.1.18.3.5.9.7.10.1.1	INTEGER	read-only	Indicates status of this entry. SMDS_SW_USAGE_CREATED is the normal case. SMDS_SW_USAGE_DELETED means this billing instance will be deleted at the end of the next wfSmdsSwUsageFlush period after this billing record is written out to the file system.
INT wfSmdsSwUsageSni	1.3.6.1.4.1.18.3.5.9.7.10.1.2	INTEGER	read-only	The circuit number of the interface generating the usage information
OCT wfSmdsSwUsageDestAddr	1.3.6.1.4.1.18.3.5.9.7.10.1.3	OCTET STRING	read-only	Instance identifier; the destination address of an L3_PDU. The SMDS Switch collects usage data based on the destination/source address pair.
OCT wfSmdsSwUsageSrcAddr	1.3.6.1.4.1.18.3.5.9.7.10.1.4	OCTET STRING	read-only	Instance identifier; the source address of an L3_PDU. The SMDS Switch collects usage data based on the destination/source address pair.
INT wfSmdsSwUsageStartTimeStampHigh	1.3.6.1.4.1.18.3.5.9.7.10.1.5	INTEGER	read-only	Time stamp of the starting time (the high 32 bits) of last billing usage interval. This value is the number of 1/100th seconds since midnight Jan 1, 1976 (GMT).
INT wfSmdsSwUsageStartTimeStampLow	1.3.6.1.4.1.18.3.5.9.7.10.1.6	INTEGER	read-only	Time stamp of the starting time (the low 32 bits) of last billing usage interval. This value is the number of 1/100th seconds since midnight Jan 1, 1976 (GMT).
INT wfSmdsSwUsageEndTimeStampHigh	1.3.6.1.4.1.18.3.5.9.7.10.1.7	INTEGER	read-only	Time stamp of the ending time (the high 32 bits) of last billing usage interval. This value is the number of 1/100th seconds since midnight Jan 1, 1976 (GMT).
INT wfSmdsSwUsageEndTimeStampLow	1.3.6.1.4.1.18.3.5.9.7.10.1.8	INTEGER	read-only	Time stamp of the ending time (the low 32 bits) of last billing usage interval. This value is the number of 1/100th seconds since midnight Jan 1, 1976 (GMT).
INT wfSmdsSwUsageSentL3PduHigh	1.3.6.1.4.1.18.3.5.9.7.10.1.9	INTEGER	read-only	Number (the high 32 bits) of L3_PDUs sent to the CPE between wfSmdsSwUsageStartTimeStamp and wfSmdsSwUsageEndTimeStamp.
INT wfSmdsSwUsageSentL3PduLow	1.3.6.1.4.1.18.3.5.9.7.10.1.10	INTEGER	read-only	Number (the low 32 bits) of L3_PDUs sent to the CPE between wfSmdsSwUsageStartTimeStamp and wfSmdsSwUsageEndTimeStamp.
INT wfSmdsSwUsageSentOctetHigh	1.3.6.1.4.1.18.3.5.9.7.10.1.11	INTEGER	read-only	Number (the high 32 bits) of octets sent to the CPE between wfSmdsSwUsageStartTimeStamp and wfSmdsSwUsageEndTimeStamp.
INT wfSmdsSwUsageSentOctetLow	1.3.6.1.4.1.18.3.5.9.7.10.1.12	INTEGER	read-only	Number (the low 32 bits) of octets sent to the CPE between wfSmdsSwUsageStartTimeStamp and wfSmdsSwUsageEndTimeStamp.
INT wfSmdsSwUsageLastL3PduHigh	1.3.6.1.4.1.18.3.5.9.7.10.1.13	INTEGER	read-only	The (high 32 bits) value of wfSmdsSwCurUsageNumL3Pdu value at wfSmdsSwUsageEndTimeStamp. Note: Since wfSmdsSwCurUsageNumL3Pdu is a 32-bit COUNTER, this is really a counter keeping track of number of times wfSmdsSwCurUsageNumL3Pdu has wrapped around.
INT wfSmdsSwUsageLastL3PduLow	1.3.6.1.4.1.18.3.5.9.7.10.1.14	INTEGER	read-only	The (low 32 bits) value of wfSmdsSwCurUsageNumL3Pdu value at wfSmdsSwUsageEndTimeStamp.
INT wfSmdsSwUsageLastOctetHigh	1.3.6.1.4.1.18.3.5.9.7.10.1.15	INTEGER	read-only	The (high 32 bits) value of wfSmdsSwCurUsageNumOctets value at wfSmdsSwUsageEndTimeStamp. Note: Since wfSmdsSwCurUsageNumOctets is a 32-bit COUNTER, this is really a counter keeping track of number of times wfSmdsSwCurUsageNumOctets has wrapped around.
INT wfSmdsSwUsageLastOctetLow	1.3.6.1.4.1.18.3.5.9.7.10.1.16	INTEGER	read-only	The (low 32 bits) value of wfSmdsSwCurUsageNumOctets value at wfSmdsSwUsageEndTimeStamp.
OCT wfSmdsSwUsageGrpIndAddr	1.3.6.1.4.1.18.3.5.9.7.10.1.17	OCTET STRING	read-only	When the destination address of an L3_PDU is a group address, this attribute is set to one of the E.164 individual addresses that is in the group address and on the destination SNI.
wfSmdsSwSsiSniTable	1.3.6.1.4.1.18.3.5.9.7.11		not-accessible	The Parameters for the SSI/SNI Object. This object associates SNI's with SSI's for Bellcore TR-TSV-001239 compliance.
wfSmdsSwSsiSniEntry	1.3.6.1.4.1.18.3.5.9.7.11.1		not-accessible	The parameters for a particular SSI/SNI.
INT wfSmdsSwSsiSniDelete	1.3.6.1.4.1.18.3.5.9.7.11.1.1	INTEGER	read-write	Indication to delete this SSI/SNI entry.
INT wfSmdsSwSsiSniSSI	1.3.6.1.4.1.18.3.5.9.7.11.1.2	INTEGER	read-only	An SSI.
INT wfSmdsSwSsiSniSNI	1.3.6.1.4.1.18.3.5.9.7.11.1.3	INTEGER	read-only	An SNI.

RFC description

Configures and monitors SMDS switch circuit management for Wellfleet routers including subscriber network interface parameters.

Start monitoring Wellfleet router, Bay Networks/Nortel WAN router (SMDS virtual-circuit provisioning/error-counter status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download Wellfleet-SWSMDS-MIB

What Is Wellfleet-SWSMDS-MIB?

Supported Devices

Monitoring Examples

What Can Be Monitored

This MIB depends on

Related MIBs

RFC description