All MIBs › WWP-LEOS-VPLS-MIB
Organization: Ciena, Inc
Last Updated: 2011-06-06
Category: Ciena LEOS Carrier Ethernet
Description: Manages Ciena LEOS Virtual Private LAN Service instance configuration, MAC table, and pseudowire bindings.
Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.
What Is WWP-LEOS-VPLS-MIB?
WWP-LEOS-VPLS-MIB is a World Wide Packets (Ciena) vendor MIB for the LEOS platform covering Virtual Private LAN Service, an MPLS/Ethernet technology that emulates a multipoint LAN across a service-provider core. It exposes configuration data for virtual switch instances, member service (pseudowire) bindings, VLAN tag handling, and learned MAC address table entries. Its monitoring focus is on the health and state of VPLS forwarding: an operator checks whether MPLS pseudowire members are up and correctly bound, whether the MAC table is learning expected customer addresses, and whether VLAN tag (TPID) handling is configured consistently across sites, all indicators of service-level software configuration correctness rather than raw hardware sensors. It has a clear dependency on the underlying MPLS/pseudowire signaling and standard VPLS concepts (RFC 4762) that this vendor MIB implements. It is typically deployed on Ciena/WWP LEOS switches acting as VPLS provider edge nodes, where WWP-LEOS-VPLS-MIB SNMP monitoring helps confirm pseudowire and VLAN tag consistency across carrier Ethernet and MPLS-based service-provider networks.
IPNetwork Monitor allows you to monitor SNMP objects defined in WWP-LEOS-VPLS-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.
Supported Devices
- Ciena/WWP LEOS-based Ethernet switches
- VPLS provider edge nodes
Monitoring Examples
An administrator would poll the wwpLeosVplsVirtualSwitchMplsMemberEntry table to confirm the operational state of each MPLS pseudowire member bound to a virtual switch instance, and check related VLAN service TPID objects such as wwpLeosVplsVirtualSwitchEthEvplMemberServiceVlanTpid; a member entry showing a down or mismatched state would reveal a broken pseudowire or a VLAN tag protocol identifier mismatch between provider edge nodes disrupting the VPLS service. Sample objects confirm this MIB models virtual switch instances with MPLS and Ethernet EVPL member entries as its core structures.
What Can Be Monitored
- VPLS virtual switch instance status
- MPLS pseudowire member state
- learned MAC address table entries
- VLAN service TPID configuration
This MIB depends on
Related MIBs
Imported Objects
From SNMPv2-SMI
| Counter32 | |
| Integer32 | |
| IpAddress | |
| MODULE-IDENTITY | |
| OBJECT-TYPE | |
| Unsigned32 |
From SNMPv2-TC
| DisplayString | |
| MacAddress | |
| RowStatus | |
| TEXTUAL-CONVENTION | |
| TruthValue |
From WWP-SMI
| wwpModulesLeos | OBJECT-IDENTITY |
OIDs
| OID symbolic | OID numeric | Type | Access | Description |
|---|---|---|---|---|
| wwpLeosVplsMIB | 1.3.6.1.4.1.6141.2.60.28 | Added a new object wwpLeosVplsVirtualSwitchEthEvplMemberServiceVlanTpid. | ||
| wwpLeosVplsMIBObjects | 1.3.6.1.4.1.6141.2.60.28.1 | |||
| wwpLeosVpls | 1.3.6.1.4.1.6141.2.60.28.1.1 | |||
| wwpLeosVplsVirtualCircuitTable | 1.3.6.1.4.1.6141.2.60.28.1.1.1 | not-accessible | The (conceptual) table listing the virtual circuit table. To create entry use SNMP, multiple set operation must be used because following MIB objects needs to be set while creating entry in the table. - wwpLeosVplsVirtualCircuitIndex - wwpLeosVplsVirtualCircuitProviderVlanId (should exist on the device) - wwpLeosVplsVirtualCircuitType - wwpLeosVplsVirtualCircuitStatus. - wwpLeosVplsVirtualCircuitName. | |
| wwpLeosVplsVirtualCircuitEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.1.1 | not-accessible | The virtual circuit table entry index by wwpLeosVplsVirtualCircuitIndex. | |
| INT wwpLeosVplsVirtualCircuitIndex | 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.1 | INTEGER | read-only | This represents the virtual circuit index in the table. This number should be unique in the table. |
| VLA wwpLeosVplsVirtualCircuitProviderVlanId | 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.2 | VlanId | read-write | This represents the provider vlan id associated with the virtual circuit for a given wwpLeosVplsVirtualCircuitIndex. |
| INT wwpLeosVplsVirtualCircuitType | 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.3 | INTEGER | read-create | This represents the type of virtual circuit associated with the given virtual circuit. |
| STR wwpLeosVplsVirtualCircuitName | 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.4 | DisplayString | read-create | This represents the name of the virtual circuit associated with the given virtual circuit. |
| INT wwpLeosVplsVirtualCircuitIngressVcLabel | 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.5 | INTEGER | read-write | This represents the vc label to be used for given virtual circuit. This mib object can only be set for virtual circuit entries which has wwpLeosCircuitType = mpls. |
| INT wwpLeosVplsVirtualCircuitEgressVcLabel | 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.6 | INTEGER | read-write | This represents the vc label to be used for given virtual circuit. This mib object can only be set for virtual circuit entries which has wwpLeosCircuitType = mpls. |
| INT wwpLeosVplsVirtualCircuitTunnelIndx | 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.7 | INTEGER | read-write | This represents the tunnel associated with this virtual circuit. This mib object can only be set for virtual circuit entries which has wwpLeosCircuitType = mpls. |
| ROW wwpLeosVplsVirtualCircuitStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.1.1.8 | RowStatus | read-create | Setting this object to 'createAndGo' will create the entry and by default will enable control frame and data frame tunnel . Setting this object to 'destroy' will delete the entry from the table for given vlan. |
| wwpLeosVplsVirtualSwitchTable | 1.3.6.1.4.1.6141.2.60.28.1.1.5 | not-accessible | This table is used to manage virtual switch entries on the device. | |
| wwpLeosVplsVirtualSwitchEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.5.1 | not-accessible | This entry corresponds to single entry in wwpLeosVplsVirtualSwitchTable table. To create an entry in the table following criteria must be met. - wwpLeosVplsVirtualSwitchIndx must be specified. - wwpLeosVplsVirtualSwitchStatus must be specified. - wwpLeosVplsVirtualSwitchType must be specified. - wwpLeosVplsVirtualSwitchName must be specified | |
| INT wwpLeosVplsVirtualSwitchIndx | 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.1 | INTEGER | read-only | This object specifies the virtual switch index which is used as unique index in the table. |
| OCT wwpLeosVplsVirtualSwitchName | 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.2 | OCTET STRING | read-write | This object specifies the virtual switch name. this object can only be specified at the time of creation and cannot be modified later. |
| INT wwpLeosVplsVirtualSwitchPriVc | 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.3 | INTEGER | read-write | This object specifies the primary virtual circuit ID associated with this virtual switch. To unset it set this to 0. |
| INT wwpLeosVplsVirtualSwitchSecVc | 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.4 | INTEGER | read-write | This object specifies the secondary virtual circuit ID associated with this virtual switch. To unset it set this to 0. This object is applicable if wwpLeosVplsVirtualSwitchType = mpls. |
| INT wwpLeosVplsVirtualSwitchActiveVc | 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.5 | INTEGER | read-only | This object specifies the virtual circuit which is currently used by this virtual switch instance. |
| INT wwpLeosVplsVirtualSwitchEncapCosPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.6 | INTEGER | read-write | This object specifies the ingress cos policy for given virtual switch. |
| INT wwpLeosVplsVirtualSwitchEncapFixedDot1dPri | 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.7 | INTEGER | read-write | This object specifies the ingress fixed cos attributes for given virtual switch. |
| INT wwpLeosVplsVirtualSwitchDecapCosPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.8 | INTEGER | read-write | This object specifies the egress cos policy for given virtual switch. |
| INT wwpLeosVplsVirtualSwitchDecapFixedDot1dPri | 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.9 | INTEGER | read-write | This object specifies the egress cos attributes for given virtual switch. |
| INT wwpLeosVplsVirtualSwitchSubscriberVlan | 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.10 | INTEGER | read-write | This object specifies the subscriber vlan Id for given virtual switch. |
| INT wwpLeosVplsVirtualSwitchCtrlProtocolTunnelState | 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.11 | INTEGER | read-write | This object enables or disables control protocol tunneling for a given virtual switch. |
| INT wwpLeosVplsVirtualSwitchType | 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.12 | INTEGER | read-create | This object specifies the type of virtual witch. |
| ROW wwpLeosVplsVirtualSwitchStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.5.1.13 | RowStatus | read-create | This object can be set to 'createAndGo' to create entry in the table. This object can be set to 'destroy' to delete entry in the table. Following objects must be set to valid values to create entry in the table. |
| wwpLeosVplsVirtualSwitchMemberTable | 1.3.6.1.4.1.6141.2.60.28.1.1.6 | not-accessible | This table is used to create virtual switch membership entry. | |
| wwpLeosVplsVirtualSwitchMemberEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.6.1 | not-accessible | This entry corresponds to single entry in wwpLeosVplsVirtualSwitchMemberTable table. | |
| INT wwpLeosVplsVirtualSwitchMemberPortId | 1.3.6.1.4.1.6141.2.60.28.1.1.6.1.1 | INTEGER | read-only | This object specifies the port id associated with wwpLeosVplsVirtualSwitchIndx. |
| ROW wwpLeosVplsVirtualSwitchMemberStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.6.1.2 | RowStatus | read-create | This object can be set to 'createandgo' to add entry in the table. This object can be set to 'destroy' to delete entry in the table. Refer to description of table entry to see how to create entries in the table. |
| wwpLeosVplsSwitchCtrlProtocolTable | 1.3.6.1.4.1.6141.2.60.28.1.1.7 | not-accessible | The (conceptual) table listing the l2 virtual switch control frame protocol status tunnel for a given Vpls. | |
| wwpLeosVplsSwitchCtrlProtocolEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.7.1 | not-accessible | The layer 2 virtual switch control frame protocol tunnel entry for the Vpls. | |
| INT wwpLeosVplsSwitchCtrlProtocolNum | 1.3.6.1.4.1.6141.2.60.28.1.1.7.1.1 | INTEGER | read-only | This object represent the list of protocols the device can support. |
| INT wwpLeosVplsSwitchCtrlType | 1.3.6.1.4.1.6141.2.60.28.1.1.7.1.2 | INTEGER | read-create | Setting this object to 'discard' will cause wwpLeosVplsSwitchCtrlProtocolNum frames arriving at the specified UNI to be discarded. Setting this to 'peer' will cause the wwpLeosVplsSwitchCtrlProtocolNum frame to be processed by the provider network and cause the provider network to behave as a peer. Setting this to 'tunnel' will cause the wwpLeosVplsSwitchCtrlProtocolNum frame to be tunneled. |
| wwpLeosVplsSwitchReservedVlanTable | 1.3.6.1.4.1.6141.2.60.28.1.1.8 | not-accessible | The (conceptual) table listing the reserved Vlans used for virtual switch. | |
| wwpLeosVplsSwitchReservedVlanEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.8.1 | not-accessible | The entry to reserve vlans for vlan switch. | |
| INT wwpLeosVplsSwitchReservedVlanId | 1.3.6.1.4.1.6141.2.60.28.1.1.8.1.1 | INTEGER | read-only | This object is used to specify the vlan ID to be reserved for virtual switch. Reserved vlans are used when virtual switch is created. |
| ROW wwpLeosVplsSwitchReservedVlanStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.8.1.2 | RowStatus | read-create | Setting this object to 'createandgo' will reserve the vlan for virtual switch. Setting this object to 'destroy will no longer be reserved for virtual switch. |
| wwpLeosVplsGlobalAttrs | 1.3.6.1.4.1.6141.2.60.28.1.1.9 | |||
| INT wwpLeosVplsTunnelFixedTTL | 1.3.6.1.4.1.6141.2.60.28.1.1.9.1 | INTEGER | read-write | This object specifies the fixed TTL value for all tunnels. |
| INT wwpLeosVplsResolverTimeout | 1.3.6.1.4.1.6141.2.60.28.1.1.9.2 | INTEGER | read-write | Setting this object will set the PE resolver timeout. This timeout value decides how frequently PE resolver will arp for the destination IP specified by wwpLeosVplsEncapTunnelDestAddr. |
| U32 wwpLeosVplsStaticLabelRangeStart | 1.3.6.1.4.1.6141.2.60.28.1.1.9.3 | Unsigned32 | read-write | Setting this object will set the lowest label that can be assigned to static encap / decap tunnels or virtual circuits. Multiple set operation can be used to set both wwpLeosVplsStaticLabelRangeStart and wwpLeosVplsStaticLabelRangeEnd. wwpLeosVplsStaticLabelRangeStart must always be less than wwpLeosVplsStaticLabelRangeEnd. The value of 0 means label range is not available. Attempting to set this object to 0 will return COMMIT FAILED. |
| U32 wwpLeosVplsStaticLabelRangeEnd | 1.3.6.1.4.1.6141.2.60.28.1.1.9.4 | Unsigned32 | read-write | Setting this object will set the maximum label that can be assigned to static encap / decap tunnels or virtual circuits. Multiple set operation can be used to set both wwpLeosVplsStaticLabelRangeStart and wwpLeosVplsStaticLabelRangeEnd. wwpLeosVplsStaticLabelRangeStart must always be less than wwpLeosVplsStaticLabelRangeEnd.The value of 0 means label range is not available. Attempting to set this object to 0 will return COMMIT FAILED. |
| U32 wwpLeosVplsDynamicLabelRangeStart | 1.3.6.1.4.1.6141.2.60.28.1.1.9.5 | Unsigned32 | read-write | Setting this object will set the lowest label that can be assigned to dynamic encap / decap tunnels or virtual circuits. Multiple set operation can be used to set both wwpLeosVplsDynamicLabelRangeStart and wwpLeosVplsDynamicLabelRangeEnd. wwpLeosVplsDynamicLabelRangeStart must always be less than wwpLeosVplsDynamicLabelRangeEnd.The value of 0 means label range is not available. Attempting to set this object to 0 will return COMMIT FAILED. |
| U32 wwpLeosVplsDynamicLabelRangeEnd | 1.3.6.1.4.1.6141.2.60.28.1.1.9.6 | Unsigned32 | read-write | Setting this object will set the maximum label that will be assigned to encap tunnels or virtual circuits. Multiple set operation can be used to set both wwpLeosVplsDynamicLabelRangeStart and wwpLeosVplsDynamicLabelRangeEnd. wwpLeosVplsDynamicLabelRangeStart must always be less than wwpLeosVplsDynamicLabelRangeEnd. The value of 0 means label range is not available. Attempting to set this object to 0 will return COMMIT FAILED. |
| INT wwpLeosVplsVirtualCircuitStatsClear | 1.3.6.1.4.1.6141.2.60.28.1.1.9.7 | INTEGER | read-write | Setting this object to clear will reset statistics for all virtual circuits |
| wwpLeosVplsMplsPathTable | 1.3.6.1.4.1.6141.2.60.28.1.1.10 | not-accessible | Mpls Path table used to represent the explicit path for RSVP tunnels. | |
| wwpLeosVplsMplsPathEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.10.1 | not-accessible | Entry in the MPLS Path table. | |
| INT wwpLeosVplsMplsPathIndex | 1.3.6.1.4.1.6141.2.60.28.1.1.10.1.1 | INTEGER | read-only | This mib specifies the unique entry in the Mpls path table. This is the primary index into this table identifying a particular explicit route object |
| STR wwpLeosVplsMplsPathName | 1.3.6.1.4.1.6141.2.60.28.1.1.10.1.2 | DisplayString | read-create | This mib specifies the name for the path. |
| ROW wwpLeosVplsMplsPathRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.10.1.3 | RowStatus | read-create | Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy'. If the entry exists, it will be displayed as 'active'. |
| wwpLeosVplsMplsPathMemberTable | 1.3.6.1.4.1.6141.2.60.28.1.1.11 | not-accessible | Table specifies the list of IP addresses (Hops) to get to the destination PE. | |
| wwpLeosVplsMplsPathMemberEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.11.1 | not-accessible | Represents the entry in the table. | |
| INT wwpLeosVplsMplsPathOptionIndex | 1.3.6.1.4.1.6141.2.60.28.1.1.11.1.1 | INTEGER | read-only | Secondary index into this table identifying a particular group of hops representing a particular configured path. This is otherwise known as a path option. |
| INT wwpLeosVplsMplsPathMemberIpIndex | 1.3.6.1.4.1.6141.2.60.28.1.1.11.1.2 | INTEGER | read-only | Unique index to identify the IP address within the path specifies by wwpLeosVplsMplsPathIndex. |
| IP wwpLeosVplsMplsPathMemberIp | 1.3.6.1.4.1.6141.2.60.28.1.1.11.1.3 | IpAddress | read-create | Specifies the IP address of the Hop that the tunnel the tunnel should traverse. |
| ROW wwpLeosVplsMplsPathMemberRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.11.1.4 | RowStatus | read-create | Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy'. If the entry exists, it will be displayed as 'active'. |
| wwpLeosVplsRsvpAttrTable | 1.3.6.1.4.1.6141.2.60.28.1.1.12 | not-accessible | RSVP Attr Table used by MPLS wwpLeosVplsEncapTunnelTable Tunnels when wwpLeosVplsEncapTunnelProtType = rsvp. Whenever entry is created in the wwpLeosVplsEncapTunnelTable table with wwpLeosVplsEncapTunnelProtType = rsvp and wwpLeosVplsEncapTunnelType = dynamic then corresponding entry will be created in this table with the same index as wwpLeosVplsEncapTunnelId. | |
| wwpLeosVplsRsvpAttrEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.12.1 | not-accessible | Entry in wwpLeosVplsRsvpAttrTable table. | |
| INT wwpLeosVplsRsvpAttrIndex | 1.3.6.1.4.1.6141.2.60.28.1.1.12.1.1 | INTEGER | read-only | Unique index into the table. |
| INT wwpLeosVplsRsvpAttrHoldPri | 1.3.6.1.4.1.6141.2.60.28.1.1.12.1.2 | INTEGER | read-write | The Hold priority used by RSVP protocol when signaling for tunnels. |
| INT wwpLeosVplsRsvpAttrSetupPri | 1.3.6.1.4.1.6141.2.60.28.1.1.12.1.3 | INTEGER | read-write | The setup priority used by RSVP protocol when signaling for tunnels. |
| T/F wwpLeosVplsRsvpAttrRecordRoute | 1.3.6.1.4.1.6141.2.60.28.1.1.12.1.4 | TruthValue | read-write | The object specifies if record route feature is enabled when RSVP protocol is used to signal tunnel LSP. |
| wwpLeosVplsEncapTunnelTable | 1.3.6.1.4.1.6141.2.60.28.1.1.13 | not-accessible | This table represents the encap tunnels for VPLS. To create STATIC encap tunnel following objects must be set Encap and Decap Tunnel name cannot be same but indexes can be wwpLeosVplsEncapTunnelName must be specified. wwpLeosVplsEncapTunnelEncapLabel must be specified (0, 32..1023) wwpLeosVplsEncapTunnelType must be set to static wwpLeosVplsEncapTunnelRowStatus must be set to createAndGo To create DYNAMIC encap tunnel following objects must be set wwpLeosVplsEncapTunnelName must be specified wwpLeosVplsEncapTunnelType must be set to dynamic wwpLeosVplsEncapTunnelProtType must be set to rsvp wwpLeosVplsEncapTunnelPathName must be specified, this path must exist in wwpLeosVplsMplsPathTable wwpLeosVplsEncapTunnelRowStatus must be set to createAndGo. wwpLeosVplsEncapTunnelFastReroute must be set if wanted to use fast reroute wwpLeosVplsEncapTunnelLspType must be specified, if not specified then it will be assumed primary To create DYNAMIC encap backup tunnel following objects must be set wwpLeosVplsEncapTunnelName must be set to primary tunnel name that this tunnel is backing up. wwpLeosVplsEncapTunnelType must be set to dynamic wwpLeosVplsEncapTunnelProtType must be set to rsvp wwpLeosVplsEncapTunnelPathName must be specified, this path must exist in wwpLeosVplsMplsPathTable wwpLeosVplsEncapTunnelRowStatus must be set to createAndGo. To create static PBT encap tunnel following objects must be set wwpLeosVplsEncapTunnelName must be specified wwpLeosVplsEncapTunnelType must be set to staticPbt wwpLeosVplsEncapTunnelBVID must be specified wwpLeosVplsEncapTunnelRowStatus must be set to createAndGo. wwpLeosVplsEncapTunnelDestBridgeIndex must be set wwpLeosVplsEncapTunnelEgressPort must be specified | |
| wwpLeosVplsEncapTunnelEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1 | not-accessible | Represents each entry in wwpLeosVplsEncapTunnelTable. | |
| INT wwpLeosVplsEncapTunnelId | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.1 | INTEGER | read-only | This object specifies the unique index used in the table. |
| STR wwpLeosVplsEncapTunnelName | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.2 | DisplayString | read-create | This object specfies the name assigned to this tunnel. This object can only be specified while creating entry in the table and cannot be modified after the entry has been created. Encap and Decap Tunnel name cannot be same but indexes can be. When creating backup tunnel this name should be set to same name that is also used by primary tunnel. |
| INT wwpLeosVplsEncapTunnelType | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.3 | INTEGER | read-create | This object specifies the type of tunnel. This object can only be specified while creating entry in the table and cannot be modified after the entry has been created. |
| IP wwpLeosVplsEncapTunnelDestAddr | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.4 | IpAddress | read-write | This object specifies the IP address used to resolve this tunnel. This object is only applicable if wwpLeosVplsEncapTunnelType not equal to staticPbt. |
| I32 wwpLeosVplsEncapTunnelPathIndex | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.5 | Integer32 | read-create | This object specifies the path that this tunnel is supposed to use signal labels for this tunnel. This object is only used if wwpLeosVplsEncapTunnelType is set to dynamic. |
| INT wwpLeosVplsEncapTunnelEncapCosPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.6 | INTEGER | read-write | This object specifies the PBT encapsulated cos policy assigned to this tunnel. inheritVC and inheritVs options are deprecated and should not be used. rcos-mapped option should be used in place of inheritVc |
| INT wwpLeosVplsEncapTunnelEncapFixedExp | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.7 | INTEGER | read-write | This object specifies the encap fixed EXP assigned to this tunnel. |
| INT wwpLeosVplsEncapTunnelTTLPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.8 | INTEGER | read-write | This object specifies the TTL policy for given tunnel. |
| U32 wwpLeosVplsEncapTunnelEncapLabel | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.9 | Unsigned32 | read-write | This mib object specifies the encap label assigned to this tunnel. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF. |
| INT wwpLeosVplsEncapTunnelProtType | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.10 | INTEGER | read-create | Setting this object at the time of entry creation will specify the type of Protocol to be used for this tunnel. This object is only used if wwpLeosVplsEncapTunnelType is set to dynamic. This object cannot be modified after the entry has been created. |
| MAC wwpLeosVplsEncapTunnelDestResolvedMac | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.11 | MacAddress | read-only | This object specifies the resolved mac address for given destination IP (wwpLeosVplsEncapTunnelDestIp). |
| INT wwpLeosVplsEncapTunnelOperStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.12 | INTEGER | read-only | This mib object represents the operational status of tunnel. |
| INT wwpLeosVplsEncapTunnelAdminStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.13 | INTEGER | read-write | This mib object represents the administrative status of tunnel. |
| INT wwpLeosVplsEncapTunnelDestResolvedPort | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.14 | INTEGER | read-only | This mib object represents the resolved port number to destination. |
| INT wwpLeosVplsEncapTunnelDestResolvedVlan | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.15 | INTEGER | read-only | This mib object represents the resolved transport vlan to destination. |
| ROW wwpLeosVplsEncapTunnelRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.16 | RowStatus | read-create | Setting this object to 'createAndGo' will create the entry in the table. Setting this object to 'destroy' will delete the entry from the table. Refer to description of wwpLeosVplsEncapTunnelTable for details of creating and deleting entries in the table. |
| INT wwpLeosVplsEncapTunnelFastReroute | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.17 | INTEGER | read-create | This object specifies if the backup tunnel should provide link or node protection. This object should only be specified if wwpLeosVplsEncapTunnelType = dynamic and wwpLeosVplsEncapTunnelLspType = backup. This object cannot be modified once created. |
| INT wwpLeosVplsEncapTunnelLspType | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.18 | INTEGER | read-create | This object specifies if the tunnel lsp is primary or backup tunnel. |
| INT wwpLeosVplsEncapTunnelPartnerTunnelId | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.19 | INTEGER | read-only | This object specifies if the partner tunnel ID. |
| VLA wwpLeosVplsEncapTunnelBVID | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.20 | VlanId | read-create | This object specifies the provider backbone bridge vlan. This object is only applicable if wwpLeosVplsEncapTunnelType is set to staticPbt otherwise this object will be ignored. |
| I32 wwpLeosVplsEncapTunnelDestBridgeIndex | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.21 | Integer32 | read-create | This object specifies the provider backbone bridge index. This object is only applicable if wwpLeosVplsEncapTunnelType is set to staticPbt otherwise this object will be ignored. This object must be set to one of the values specified by wwpLeosPbtBridgeNameMacMapIndex. If this object is set to 0 then this value will be ignored. |
| I32 wwpLeosVplsEncapTunnelEgressPort | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.22 | Integer32 | read-create | This object specifies the provider backbone bridge port. This object is only applicable if wwpLeosVplsEncapTunnelType is set to staticPbt otherwise this object will be ignored. |
| INT wwpLeosVplsEncapTunnelEncapFixedPCP | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.23 | INTEGER | read-create | This object specifies the encap fixed PCP assigned to this tunnel. |
| INT wwpLeosVplsEncapTunnelActive | 1.3.6.1.4.1.6141.2.60.28.1.1.13.1.24 | INTEGER | read-only | This object specifes if the tunnel is active, and it is only valid if TunnelType is staticPbt. |
| wwpLeosVplsDecapTunnelTable | 1.3.6.1.4.1.6141.2.60.28.1.1.14 | not-accessible | This table represents the Decap tunnels for VPLS wwpLeosVplsDecapTunnelType If not set will default to static To create STATIC Decap tunnel following objects must be set Encap and Decap Tunnel name cannot be same but indexes can be wwpLeosVplsDecapTunnelName must be specified wwpLeosVplsDecapTunnelLabel must be specified (0, 32..1023) wwpLeosVplsDecapTunnelRowStatus must be set to createAndGo. To create STATIC Decap PBT tunnel following objects must be set Encap and Decap Tunnel name cannot be same but indexes can be wwpLeosVplsDecapTunnelType must be set to staticPbt wwpLeosVplsDecapTunnelName must be specified wwpLeosVplsDecapTunnelBVID must be specified wwpLeosVplsDecapTunnelBridgeIndex must be specified wwpLeosVplsDecapTunnelPort must be specified wwpLeosVplsDecapTunnelRowStatus must be set to createAndGo. | |
| wwpLeosVplsDecapTunnelEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.14.1 | not-accessible | represents each entry in wwpLeosVplsDecapTunnelTable. | |
| INT wwpLeosVplsDecapTunnelId | 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.1 | INTEGER | read-only | This object specifies the unique index used in the table. |
| STR wwpLeosVplsDecapTunnelName | 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.2 | DisplayString | read-create | This object specfies the name assigned to the tunnel. This object can only be specified while creating entry in the table and cannot be modified after the entry has been created. |
| U32 wwpLeosVplsDecapTunnelLabel | 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.3 | Unsigned32 | read-write | This mib object specifies the Decap label assigned to this tunnel. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF. |
| INT wwpLeosVplsDecapTunnelType | 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.4 | INTEGER | read-create | This object specifies if the tunnel is created because of remote PE request (dynamic tunnel) or it is created by the user on the device (Decap tunnel). This object cannot be set to dynamic. |
| ROW wwpLeosVplsDecapTunnelRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.5 | RowStatus | read-create | Setting this object to 'createAndGo' will create the entry in the table. Setting this object to 'destroy' will delete the entry from the table. Refer to description of wwpLeosVplsDecapTunnelTable for details of creating and deleting entries in the table. |
| I32 wwpLeosVplsDecapTunnelBVID | 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.6 | Integer32 | read-create | This object specifies the provider bridge vlan ID expected in the mac in mac frames ingressing the device from provider bridge facing side. |
| I32 wwpLeosVplsDecapTunnelBridgeIndex | 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.7 | Integer32 | read-create | This object specifies the provider bridge host index which will be used to query wwpLeosPbtHostNameMacMapTable to find out corresponding mac address expected in the pbt frames ingressing the device from provider bridge facing side. |
| I32 wwpLeosVplsDecapTunnelPort | 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.8 | Integer32 | read-create | This object specifies the incoming port on which the pbt frames are expected. |
| MAC wwpLeosVplsDecapTunnelMac | 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.9 | MacAddress | read-only | This object specifies the source mac address expected in the pbt frames coming from provider network facing side. This mac address is derived from wwpLeosPbtHostNameMacMapTable table using the value specified by wwpLeosVplsDecapTunnelBridgeName. |
| INT wwpLeosVplsDecapTunnelOperStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.14.1.10 | INTEGER | read-only | This object represents the operational status of tunnel. |
| wwpLeosVplsVirtualCircuitMplsTable | 1.3.6.1.4.1.6141.2.60.28.1.1.15 | not-accessible | The (conceptual) table listing the mpls virtual circuit table. To create entry use SNMP, multiple set operation must be used. Following Mib objects must be specified while creating MPLS virtual circuit Mpls and Ethernet virtual circuit name cannot be same but indexes can be - wwpLeosVplsVirtualCircuitMplsType must be set to dynamic - wwpLeosVplsVirtualCircuitMplsStatus must be set to createAndGo - wwpLeosVplsVirtualCircuitMplsName must be specified - wwpLeosVplsVirtualCircuitMplsDestAddr must be specified Following MIB objects must be specified while creating static MPLS virtual circuit - wwpLeosVplsVirtualCircuitMplsType must be set to static - wwpLeosVplsVirtualCircuitMplsStatus must be set to createAndGo - wwpLeosVplsVirtualCircuitMplsName must be specified - wwpLeosVplsVirtualCircuitMplsDestAddr must be specified - wwpLeosVplsVirtualCircuitMplsEncapLabel must be specified (2048..18431) - wwpLeosVplsVirtualCircuitMplsDecapLabel must be specified (2048..18431) | |
| wwpLeosVplsVirtualCircuitMplsEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1 | not-accessible | The virtual circuit table entry index by wwpLeosVplsVirtualCircuitMplsIndex. | |
| INT wwpLeosVplsVirtualCircuitMplsIndex | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.1 | INTEGER | read-only | This represents the virtual circuit index in the table. This number should be unique in the table. |
| STR wwpLeosVplsVirtualCircuitMplsName | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.2 | DisplayString | read-create | This represents the name of the virtual circuit associated with the given virtual circuit. Mpls and Ethernet virtual circuit name cannot be same but indexes can be. |
| INT wwpLeosVplsVirtualCircuitMplsType | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.3 | INTEGER | read-create | This represents the type of the virtual circuit. |
| IP wwpLeosVplsVirtualCircuitMplsDestAddr | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.4 | IpAddress | read-create | This represents the destination address used by the signaling protocol if wwpLeosVplsVirtualCircuitMplsType is set to dynamic. This object cannot be modified once entry is created. |
| INT wwpLeosVplsVirtualCircuitMplsTunnelPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.5 | INTEGER | read-create | This object represents that this virtual circuit should select the tunnel as fixed or use the first active tunnel available on the outgoing port. If this object is set to fixed then wwpLeosVplsVirtualCircuitMplsTunnelIndx must be specified. |
| INT wwpLeosVplsVirtualCircuitMplsFixedTunnelId | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.6 | INTEGER | read-create | This represents the tunnel that this virtual circuit should be mapped to. This object is only used if wwpLeosVplsVirtualCircuitMplsTunnelPolicy is set to fixed. |
| INT wwpLeosVplsVirtualCircuitMplsActiveTunnelId | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.7 | INTEGER | read-only | This represents the tunnel that this virtual circuit is currently using. This object is equal to wwpLeosVplsVirtualCircuitMplsFixedTunnelId if wwpLeosVplsVirtualCircuitMplsTunnelPolicy is set to fixed. |
| INT wwpLeosVplsVirtualCircuitMplsOperStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.8 | INTEGER | read-only | This represents the operational status of the virtual circuit. |
| U32 wwpLeosVplsVirtualCircuitMplsEncapLabel | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.9 | Unsigned32 | read-create | If wwpLeosVplsVirtualCircuitMplsType is set to static then this object specifies the encap label the should be used for this virtual circuit. Label should be in the range 2048..18431. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF. |
| U32 wwpLeosVplsVirtualCircuitMplsDecapLabel | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.10 | Unsigned32 | read-create | If wwpLeosVplsVirtualCircuitMplsType is set to static then this object specifies the decap label the should be used for this virtual circuit. Label should be in the range 2048..18431. If the label is not yet known (signaling in process), the object should return a value of 0xFFFF. |
| U32 wwpLeosVplsVirtualCircuitMplsGroupId | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.11 | Unsigned32 | read-create | This represents the group ID advertised in the LDP signaling if wwpLeosVplsVirtualCircuitMplsType is set to dynamic. |
| INT wwpLeosVplsVirtualCircuitMplsProtectionType | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.12 | INTEGER | read-create | This represents that this virtual circuit is primary or secondary virtual circuit. If primary virtual circuit goes down that secondary virtual circuit will be used. |
| T/F wwpLeosVplsVirtualCircuitMplsStatusTlv | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.13 | TruthValue | read-create | Specifies whether the Status TLV in LDP signaling should be advertised or not. This mib object is only used if wwpLeosVplsVirtualCircuitMplsType is set to dynamic. This field cannot be modified while wwpLeosVplsVirtualCircuitMplsStatus is active |
| INT wwpLeosVplsVirtualCircuitMplsMtu | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.14 | INTEGER | read-write | Setting this object will set the MTU for this VC. This MTU is advertised to the peer if wwpLeosVplsVirtualCircuitMplsType is set to dynamic. |
| ROW wwpLeosVplsVirtualCircuitMplsStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.15.1.15 | RowStatus | read-create | Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy'. If the entry exists, it will be displayed as 'active'. |
| wwpLeosVplsVirtualCircuitMplsStatsTable | 1.3.6.1.4.1.6141.2.60.28.1.1.16 | not-accessible | The (conceptual) table listing the mpls virtual circuit stats table. | |
| wwpLeosVplsVirtualCircuitMplsStatsEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.16.1 | not-accessible | The mpls virtual circuit stats table entry index by wwpLeosVplsVirtualCircuitMplsIndex. | |
| C32 wwpLeosVplsVirtualCircuitMplsTxBytesHi | 1.3.6.1.4.1.6141.2.60.28.1.1.16.1.1 | Counter32 | read-only | This represents the total number of higher 32 bits transmitted for given virtual circuit. |
| C32 wwpLeosVplsVirtualCircuitMplsTxBytesLo | 1.3.6.1.4.1.6141.2.60.28.1.1.16.1.2 | Counter32 | read-only | This represents the total number of lower 32 bits transmitted for given virtual circuit. |
| C32 wwpLeosVplsVirtualCircuitMplsRxBytesHi | 1.3.6.1.4.1.6141.2.60.28.1.1.16.1.3 | Counter32 | read-only | This represents the total number of higher 32 bits received for given mpls virtual circuit. |
| C32 wwpLeosVplsVirtualCircuitMplsRxBytesLo | 1.3.6.1.4.1.6141.2.60.28.1.1.16.1.4 | Counter32 | read-only | This represents the total number of lower 32 bits received for given virtual circuit. |
| wwpLeosVplsVirtualCircuitEthTable | 1.3.6.1.4.1.6141.2.60.28.1.1.17 | not-accessible | The (conceptual) table listing the virtual circuit table. To create entry use SNMP, multiple set operation must be usedd because following mib objects needs to be set while creating entry in the table. Mpls and Ethernet virtual circuit name cannot be same but indexes can be - wwpLeosVplsVirtualCircuitEthName must be specified - wwpLeosVplsVirtualCircuitEthProviderVlanId must be specified and must exist on the device. - wwpLeosVplsVirtualCircuitEthStatus must be specified. | |
| wwpLeosVplsVirtualCircuitEthEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.17.1 | not-accessible | The virtual circuit table entry index by wwpLeosVplsVirtualCircuitMplsIndex. | |
| INT wwpLeosVplsVirtualCircuitEthIndex | 1.3.6.1.4.1.6141.2.60.28.1.1.17.1.1 | INTEGER | read-only | This represents the virtual circuit index in the table. This number should be unique in the table. |
| STR wwpLeosVplsVirtualCircuitEthName | 1.3.6.1.4.1.6141.2.60.28.1.1.17.1.2 | DisplayString | read-create | This represents the name of the virtual circuit associated with the given virtual circuit. Mpls and Ethernet virtual circuit name cannot be same but indexes can be |
| VLA wwpLeosVplsVirtualCircuitEthProviderVlanId | 1.3.6.1.4.1.6141.2.60.28.1.1.17.1.3 | VlanId | read-write | This represents the provider vlan id associated with the virtual circuit for a given wwpLeosVplsVirtualCircuitMplsIndex. |
| ROW wwpLeosVplsVirtualCircuitEthRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.17.1.4 | RowStatus | read-create | Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy' If the entry exists, it will be displayed as 'active'. |
| INT wwpLeosVplsVirtualCircuitEthStatsMonitor | 1.3.6.1.4.1.6141.2.60.28.1.1.17.1.5 | INTEGER | read-create | To disable stats collection, set this object to off(2). To enable stats collection, set this object to on(1). |
| wwpLeosVplsVirtualCircuitEtherTypeTable | 1.3.6.1.4.1.6141.2.60.28.1.1.18 | not-accessible | The (conceptual) table listing the ether type to be used for each port. | |
| wwpLeosVplsVirtualCircuitEtherTypeEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.18.1 | not-accessible | The entry to assign ether type for each port. | |
| INT wwpLeosVplsVirtualCircuitPortId | 1.3.6.1.4.1.6141.2.60.28.1.1.18.1.1 | INTEGER | read-write | This object specifies the port number used as index in the table. |
| INT wwpLeosVplsVirtualCircuitEtherType | 1.3.6.1.4.1.6141.2.60.28.1.1.18.1.2 | INTEGER | read-write | This object specifies the ethertype of the outer VLAN tag for given port. |
| INT wwpLeosVplsVirtualCircuitEtherTypePolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.18.1.3 | INTEGER | read-write | This object specifies the policy for the ethertype of the outer VLAN tag for given port. All means all frames will have the type set in wwpLeosVplsVirtualCircuitEtherType. encapOnly means only Q-in-Q encapsulated frames will use that value. If wwpLeosVplsVirtualCircuitEtherType is set to type 8100 then ALL will always be the operational value for this item. vlanTpid means that the port will use the TPID configured for the vlan at egress. |
| wwpLeosVplsVirtualCircuitEthStatsTable | 1.3.6.1.4.1.6141.2.60.28.1.1.19 | not-accessible | The (conceptual) table listing the virtual circuit stats table. | |
| wwpLeosVplsVirtualCircuitEthStatsEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.19.1 | not-accessible | The ethernet virtual circuit stats table entry index by wwpLeosVplsVirtualCircuitMplsIndex. | |
| C32 wwpLeosVplsVirtualCircuitEthTxBytesHi | 1.3.6.1.4.1.6141.2.60.28.1.1.19.1.1 | Counter32 | read-only | This represents the total number of higher 32 bits transmitted for given virtual circuit. |
| C32 wwpLeosVplsVirtualCircuitEthTxBytesLo | 1.3.6.1.4.1.6141.2.60.28.1.1.19.1.2 | Counter32 | read-only | This represents the total number of lower 32 bits transmitted for given virtual circuit. |
| C32 wwpLeosVplsVirtualCircuitEthRxBytesHi | 1.3.6.1.4.1.6141.2.60.28.1.1.19.1.3 | Counter32 | read-only | This represents the total number of higher 32 bits received for given virtual circuit. |
| C32 wwpLeosVplsVirtualCircuitEthRxBytesLo | 1.3.6.1.4.1.6141.2.60.28.1.1.19.1.4 | Counter32 | read-only | This represents the total number of lower 32 bits received for given virtual circuit. |
| INT wwpLeosVirtualCircuitEthStatsClear | 1.3.6.1.4.1.6141.2.60.28.1.1.19.1.5 | INTEGER | read-write | To clear the statistics for the given virtual circuit, set this object to clear(1) |
| wwpLeosVplsVirtualSwitchMplsTable | 1.3.6.1.4.1.6141.2.60.28.1.1.20 | not-accessible | This table is used to manage virtual switch entries on the device. | |
| wwpLeosVplsVirtualSwitchMplsEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1 | not-accessible | This entry corresponds to single entry in wwpLeosVplsVirtualSwitchMplsTable table. To create an entry in the table following criteria must be met. Mpls and Ethernet virtual switch name cannot be same but indexes can be - wwpLeosVplsVirtualSwitchMplsVpnId must be specified. - wwpLeosVplsVirtualSwitchMplsType must be specified. - wwpLeosVplsVirtualSwitchMplsName must be specified. - wwpLeosVplsVirtualSwitchMplsStatus must be specified. | |
| INT wwpLeosVplsVirtualSwitchMplsIndx | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.1 | INTEGER | read-only | This object specifies the virtual switch index which is used as unique index in the table. |
| STR wwpLeosVplsVirtualSwitchMplsName | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.2 | DisplayString | read-write | This object specifies the virtual switch name. this object can only be specified at the time of creation and cannot be modified later. Mpls and Ethernet virtual switch name cannot be same but indexes can be. |
| U32 wwpLeosVplsVirtualSwitchMplsVpnId | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.3 | Unsigned32 | read-write | This object specifies the subscriber vlan Id for given virtual switch. |
| INT wwpLeosVplsVirtualSwitchMplsEncapCosPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.4 | INTEGER | read-write | This object specifies the ingress cos policy for given virtual switch. |
| INT wwpLeosVplsVirtualSwitchMplsEncapFixedDot1dPri | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.5 | INTEGER | read-write | This object specifies the ingress fixed cos attributes for given virtual switch. |
| INT wwpLeosVplsVirtualSwitchMplsDecapCosPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.6 | INTEGER | read-write | This object specifies the egress cos policy for given virtual switch. |
| INT wwpLeosVplsVirtualSwitchMplsDecapFixedDot1dPri | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.7 | INTEGER | read-write | This object specifies the egress cos attributes for given virtual switch. |
| INT wwpLeosVplsVirtualSwitchMplsCtrlProtocolTunnelState | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.8 | INTEGER | read-write | This object enables or disables control protocol tunneling for a given virtual switch. |
| INT wwpLeosVplsVirtualSwitchMplsDecapTTLPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.9 | INTEGER | read-write | This object specifies the TTL policy for a given virtual switch. |
| INT wwpLeosVplsVirtualSwitchMplsType | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.10 | INTEGER | read-create | This object specifies the type of virtual switch. |
| ROW wwpLeosVplsVirtualSwitchMplsRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.11 | RowStatus | read-create | This object can be set to 'createAndGo' to create entry in the table. This object can be set to 'destroy' to delete entry in the table. Following objects must be set to valid values to create entry in the table. |
| INT wwpLeosVplsVirtualSwitchMplsMacLrnState | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.12 | INTEGER | read-write | Setting this object will set the Mac learning state for a given mpls virtual switch. |
| INT wwpLeosVplsVirtualSwitchMplsTunnelMethod | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.13 | INTEGER | read-write | Setting this object will set the tunneling method for a given mpls virtual switch. |
| INT wwpLeosVplsVirtualSwitchMplsCtrlProtocolDot1dPri | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.14 | INTEGER | read-write | This object specifies the .1d priority to use when encapsulation control frames. |
| INT wwpLeosVplsVirtualSwitchMplsSubscriberDot1dPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.15 | INTEGER | read-write | Setting this object will configure the policy used to decide whether or not the subscriber frame .1d priorty should be left alone, or remarked to the computed provider priority. |
| INT wwpLeosVplsVirtualSwitchMplsCtrlProtTransFrameValidate | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.16 | INTEGER | read-write | Setting this object will set the transparent-mode validate for a given mpls virtual switch. |
| INT wwpLeosVplsVirtualSwitchMplsHonorPriority | 1.3.6.1.4.1.6141.2.60.28.1.1.20.1.17 | INTEGER | read-write | Setting this object will select either the c-vlan or s-vlan priority to use through the Virtual Switch and it's associated MPLS Tunnel. |
| wwpLeosVplsVirtualSwitchMplsMemberTable | 1.3.6.1.4.1.6141.2.60.28.1.1.21 | not-accessible | This table is used to create mpls virtual switch subscriber port-vlan membership entry. | |
| wwpLeosVplsVirtualSwitchMplsMemberEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.21.1 | not-accessible | This entry corresponds to single port-vlan subscriber entry in wwpLeosVplsVirtualSwitchMplsMemberTable table. | |
| INT wwpLeosVplsVirtualSwitchMplsMemberPortId | 1.3.6.1.4.1.6141.2.60.28.1.1.21.1.1 | INTEGER | read-create | This object specifies the port number which is to be added as a customer facing port for the mpls virtual switch index wwpLeosVplsVirtualSwitchMplsIndx. |
| INT wwpLeosVplsVirtualSwitchMplsMemberVlanId | 1.3.6.1.4.1.6141.2.60.28.1.1.21.1.2 | INTEGER | read-create | This object specifies the subscriber vlan attached to this mpls virtual switch index wwpLeosVplsVirtualSwitchMplsIndx. This object cannot be modified one entry is created in this table. This object can only be specified when creating entries in this table. |
| ROW wwpLeosVplsVirtualSwitchMplsMemberRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.21.1.3 | RowStatus | read-create | Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy'. If the entry exists, it will be displayed as 'active'. |
| INT wwpLeosVplsVirtualSwitchMplsMemberEncapCosPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.21.1.4 | INTEGER | read-write | This object specifies the ingress cos policy for given member entry. By default 'inheritVs' the encap CoS policy is inherited from the parent virtual-switch settings |
| INT wwpLeosVplsVirtualSwitchMplsMemberEncapCosFixedDot1DPri | 1.3.6.1.4.1.6141.2.60.28.1.1.21.1.5 | INTEGER | read-write | This object specifies the ingress fixed cos attributes for given member entry. This attribute is only valid when the member EncapCosPolicy is set to 'fixed' |
| INT wwpLeosVplsVirtualSwitchMplsMemberSubscriberDot1dPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.21.1.6 | INTEGER | read-write | This object configures the member policy used to decide if the subscriber frame's 'c-vlan' .1d priorty should be left alone 'leave', or remarked 'provider-inherit' to the resolved provider 's-vlan' priority. This attribute is valid when the member's SubscriberDot1Policy is 'leave' or 'provider-inherit'. If stt to 'inheritVs' the attribute is inherited from the parent virtual-switch |
| wwpLeosVplsVirtualSwitchMplsMemberStatsTable | 1.3.6.1.4.1.6141.2.60.28.1.1.22 | not-accessible | The (conceptual) table listing the virtual switch member stats table. | |
| wwpLeosVplsVirtualSwitchMplsMemberStatsEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.22.1 | not-accessible | The virtual switch member stats table entry index by wwpLeosVplsVirtualSwitchMplsIndx and wwpLeosVplsVirtualSwitchMplsMemberPortId. | |
| C32 wwpLeosVplsVirtualSwitchMplsMemberRxBytesHi | 1.3.6.1.4.1.6141.2.60.28.1.1.22.1.1 | Counter32 | read-only | This represents the total number of higher 32 bits received for given mpls virtual switch member port. |
| C32 wwpLeosVplsVirtualSwitchMplsMemberRxBytesLo | 1.3.6.1.4.1.6141.2.60.28.1.1.22.1.2 | Counter32 | read-only | This represents the total number of lower 32 bits received for given virtual switch member port. |
| wwpLeosVplsVirtualSwitchMplsMemberMeshVcTable | 1.3.6.1.4.1.6141.2.60.28.1.1.23 | not-accessible | This table is used to create mpls virtual switch mesh-vc membership entry. | |
| wwpLeosVplsVirtualSwitchMplsMemberMeshVcEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.23.1 | not-accessible | This entry corresponds to single mesh-vc entry in wwpLeosVplsVirtualSwitchMplsMemberMeshVcTable table. | |
| INT wwpLeosVplsVirtualSwitchMplsMemberMeshVcMeshVc | 1.3.6.1.4.1.6141.2.60.28.1.1.23.1.1 | INTEGER | read-only | This object specifies the mesh virtual circuit for this mpls virtual switch. |
| ROW wwpLeosVplsVirtualSwitchMplsMemberMeshVcRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.23.1.2 | RowStatus | read-create | Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy'. If the entry exists, it will be displayed as 'active'. |
| wwpLeosVplsVirtualSwitchMplsMemberAcVcTable | 1.3.6.1.4.1.6141.2.60.28.1.1.24 | not-accessible | This table is used to create mpls virtual switch mesh-vc membership entry. | |
| wwpLeosVplsVirtualSwitchMplsMemberAcVcEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.24.1 | not-accessible | This entry corresponds to single mesh-vc entry in wwpLeosVplsVirtualSwitchMplsMemberAcVcTable table. | |
| INT wwpLeosVplsVirtualSwitchMplsMemberAcVcAcVc | 1.3.6.1.4.1.6141.2.60.28.1.1.24.1.1 | INTEGER | read-only | This object specifies the attachment virtual circuit for this mpls virtual switch. |
| ROW wwpLeosVplsVirtualSwitchMplsMemberAcVcRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.24.1.2 | RowStatus | read-create | Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy'. If the entry exists, it will be displayed as 'active'. |
| wwpLeosVplsSwitchMplsCtrlProtocolTable | 1.3.6.1.4.1.6141.2.60.28.1.1.25 | not-accessible | The (conceptual) table listing the l2 virtual switch control frame protocol status tunnel for a given Vpls. | |
| wwpLeosVplsSwitchMplsCtrlProtocolEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.25.1 | not-accessible | The layer 2 virtual switch control frame protocol tunnel entry for the Vpls. | |
| INT wwpLeosVplsSwitchMplsCtrlProtocolNum | 1.3.6.1.4.1.6141.2.60.28.1.1.25.1.1 | INTEGER | read-only | This object represent the list of protocols the device can support. |
| INT wwpLeosVplsSwitchMplsCtrlType | 1.3.6.1.4.1.6141.2.60.28.1.1.25.1.2 | INTEGER | read-create | Setting this object to 'discard' will cause wwpLeosVplsSwitchMplsCtrlProtocolNum frames arriving at the specified UNI to be discarded. Setting this to 'peer' will cause the wwpLeosVplsSwitchMplsCtrlProtocolNum frame to be processed by the provider network and cause the provider network to behave as a peer. Setting this to 'tunnel' will cause the wwpLeosVplsSwitchMplsCtrlProtocolNum frame to be tunneled. |
| wwpLeosVplsVirtualSwitchEthTable | 1.3.6.1.4.1.6141.2.60.28.1.1.26 | not-accessible | This table is used to manage virtual switch entries on the device. | |
| wwpLeosVplsVirtualSwitchEthEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1 | not-accessible | This entry corresponds to single entry in wwpLeosVplsVirtualSwitchEthernetTable table. To create an entry in the table following criteria must be met. - wwpLeosVplsVirtualSwitchEthRowStatus must be specified. - wwpLeosVplsVirtualSwitchEthernetName must be specified | |
| INT wwpLeosVplsVirtualSwitchEthIndx | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.1 | INTEGER | read-only | This object specifies the virtual switch index which is used as unique index in the table. |
| STR wwpLeosVplsVirtualSwitchEthName | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.2 | DisplayString | read-create | This object specifies the virtual switch name. this object can only be specified at the time of creation and cannot be modified later. Mpls and Ethernet virtual switch name cannot be same but indexes can be. |
| INT wwpLeosVplsVirtualSwitchEthVc | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.3 | INTEGER | read-create | This object specifies the primary virtual circuit ID associated with this virtual switch. To unset it set this to 0. If this object represents PBT virtual circuit then wwpLeosVplsVirtualSwitchEthVcType must also be set to pbt. |
| INT wwpLeosVplsVirtualSwitchEthEncapCosPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.4 | INTEGER | read-write | This object specifies the ingress cos policy for given virtual switch. |
| INT wwpLeosVplsVirtualSwitchEthEncapFixedDot1dPri | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.5 | INTEGER | read-write | This object specifies the ingress fixed cos attributes for given virtual switch. |
| INT wwpLeosVplsVirtualSwitchEthDecapCosPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.6 | INTEGER | read-write | This object specifies the egress cos policy for given virtual switch. |
| INT wwpLeosVplsVirtualSwitchEthDecapFixedDot1dPri | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.7 | INTEGER | read-write | This object specifies the egress cos attributes for given virtual switch. |
| INT wwpLeosVplsVirtualSwitchEthCtrlProtocolTunnelState | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.8 | INTEGER | read-write | This object enables or disables control protocol tunneling for a given virtual switch. |
| ROW wwpLeosVplsVirtualSwitchEthRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.9 | RowStatus | read-create | This object can be set to 'createAndGo' to create entry in the table. This object can be set to 'destroy' to delete entry in the table. Following objects must be set to valid values to create entry in the table. |
| INT wwpLeosVplsVirtualSwitchEthMacLrnState | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.10 | INTEGER | read-write | Setting this object will set the Mac learning state for each ethernet virtual switch. |
| INT wwpLeosVplsVirtualSwitchEthTunnelMethod | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.11 | INTEGER | read-write | Setting this object will set the tunneling method for each ethernet virtual switch. |
| INT wwpLeosVplsVirtualSwitchEthCtrlProtocolDot1dPri | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.12 | INTEGER | read-write | This object specifies the .1d priority to use when encapsulation control frames. |
| INT wwpLeosVplsVirtualSwitchEthSubscriberDot1dPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.13 | INTEGER | read-write | Setting this object will configure the policy used to decide whether or not the subscriber frame .1d priorty should be left alone, or remarked to the computed provider priority. |
| INT wwpLeosVplsVirtualSwitchEthCtrlProtTransFrameValidate | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.14 | INTEGER | read-write | Setting this object will set the transparent-mode validate for a given eth virtual switch. |
| INT wwpLeosVplsVirtualSwitchEthVcType | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.15 | INTEGER | read-create | This object specifies the type of vc to be attached to this virtual switch. This object must be set (using SNMP multiple set operation) to pbt type if wwpLeosVplsVirtualSwitchEthVc specifies the pbt vc. Setting only wwpLeosVplsVirtualSwitchEthVcType will return error. Also setting wwpLeosVplsVirtualSwitchEthVcType to none will return error. |
| INT wwpLeosVplsVirtualSwitchEthHonorPriority | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.16 | INTEGER | read-write | This object specifies which Vlan priority to use on a Virtual Switch. Honor either the c-vlan or the s-vlan priority through the Virtual Switch and it's associated VC or Tunnel. |
| OCT wwpLeosVplsVirtualSwitchEthDescription | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.17 | OCTET STRING | read-write | This object specifies the virtual switch description. |
| INT wwpLeosVplsVirtualSwitchEthReservedVlan | 1.3.6.1.4.1.6141.2.60.28.1.1.26.1.18 | INTEGER | read-create | Reserved vlan for the virtual-switch. |
| wwpLeosVplsVirtualSwitchEthMemberTable | 1.3.6.1.4.1.6141.2.60.28.1.1.27 | not-accessible | This table is used to create virtual switch membership entry. | |
| wwpLeosVplsVirtualSwitchEthMemberEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.27.1 | not-accessible | This entry corresponds to single entry in wwpLeosVplsVirtualSwitchEthernetMemberTable table. | |
| INT wwpLeosVplsVirtualSwitchEthMemberPortId | 1.3.6.1.4.1.6141.2.60.28.1.1.27.1.1 | INTEGER | read-only | This object specifies the port id associated with wwpLeosVplsVirtualSwitchEthIndx. |
| INT wwpLeosVplsVirtualSwitchEthMemberVlan | 1.3.6.1.4.1.6141.2.60.28.1.1.27.1.2 | INTEGER | read-create | This object specifies the subscriber vlan attached to this eth virtual switch index wwpLeosVplsVirtualSwitchEthIndx. This object cannot be modified one entry is created. This object can only be specified when entry is created in this table. |
| ROW wwpLeosVplsVirtualSwitchEthMemberRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.27.1.3 | RowStatus | read-create | This object can be set to 'createandgo' to add entry in the table. This object can be set to 'destroy' to delete entry in the table. Refer to description of table entry to see how to create entries in the table. |
| INT wwpLeosVplsVirtualSwitchEthMemberEncapCosPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.27.1.4 | INTEGER | read-write | This object specifies the ingress cos policy for given member entry. |
| INT wwpLeosVplsVirtualSwitchEthMemberEncapCosFixedDot1DPri | 1.3.6.1.4.1.6141.2.60.28.1.1.27.1.5 | INTEGER | read-write | This object specifies the ingress fixed cos attributes for given member entry. This attribute is only valid when the EncapCosPolicy is set to 'fixed' |
| INT wwpLeosVplsVirtualSwitchEthMemberSubscriberDot1dPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.27.1.6 | INTEGER | read-write | This object configures the member policy used to decide if the subscriber frame's 'c-vlan' .1d priorty should be left alone 'leave', or remarked 'provider-inherit' to the resolved provider 's-vlan' priority. This attribute is valid when the member's SubscriberDot1Policy is 'leave' or 'provider-inherit'. If stt to 'inheritVs' the attribute is inherited from the parent virtual-switch |
| wwpLeosVplsVirtualSwitchEthMemberStatsTable | 1.3.6.1.4.1.6141.2.60.28.1.1.28 | not-accessible | The (conceptual) table listing the virtual switch member stats table. | |
| wwpLeosVplsVirtualSwitchEthMemberStatsEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.28.1 | not-accessible | The virtual switch member stats table entry index by wwpLeosVplsVirtualSwitchEthIndx and wwpLeosVplsVirtualSwitchEthMemberPortId. | |
| C32 wwpLeosVplsVirtualSwitchEthMemberRxBytesHi | 1.3.6.1.4.1.6141.2.60.28.1.1.28.1.1 | Counter32 | read-only | This represents the total number of higher 32 bits received for given virtual switch member port. |
| C32 wwpLeosVplsVirtualSwitchEthMemberRxBytesLo | 1.3.6.1.4.1.6141.2.60.28.1.1.28.1.2 | Counter32 | read-only | This represents the total number of lower 32 bits received for given virtual switch member port. |
| wwpLeosVplsSwitchEthCtrlProtocolTable | 1.3.6.1.4.1.6141.2.60.28.1.1.29 | not-accessible | The (conceptual) table listing the l2 virtual switch control frame protocol status tunnel for a given Vpls. | |
| wwpLeosVplsSwitchEthCtrlProtocolEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.29.1 | not-accessible | The layer 2 virtual switch control frame protocol tunnel entry for the Vpls. | |
| INT wwpLeosVplsSwitchEthCtrlProtocolNum | 1.3.6.1.4.1.6141.2.60.28.1.1.29.1.1 | INTEGER | read-only | This object represent the list of protocols the device can support. |
| INT wwpLeosVplsSwitchEthCtrlType | 1.3.6.1.4.1.6141.2.60.28.1.1.29.1.2 | INTEGER | read-create | Setting this object to 'discard' will cause wwpLeosVplsSwitchEthCtrlProtocolNum frames arriving at the specified UNI to be discarded. Setting this to 'peer' will cause the wwpLeosVplsSwitchEthCtrlProtocolNum frame to be processed by the provider network and cause the provider network to behave as a peer. Setting this to 'tunnel' will cause the wwpLeosVplsSwitchEthCtrlProtocolNum frame to be tunneled. |
| wwpLeosVplsVirtualSwitchEtypeTranslationTable | 1.3.6.1.4.1.6141.2.60.28.1.1.30 | not-accessible | This table controls the global Ethertype translation functions. Only two entries are allowed. Creating more than two entries will return an error. The control is bi-directional. Creating one entry will enable translation as the packet egresses the NNI and as it egresses the UNI port. | |
| wwpLeosVplsVirtualSwitchEtypeTranslationEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.30.1 | not-accessible | Each entry contains the Ethertype being translated and the new Ethertype that will be copied over the old Ethertype. | |
| ETH wwpLeosVplsVirtualSwitchEtypeTranslationOriginalEtype | 1.3.6.1.4.1.6141.2.60.28.1.1.30.1.1 | EtherType | read-only | This object represent the original Ethertype of the frame. |
| ETH wwpLeosVplsVirtualSwitchEtypeTranslationMappedEtype | 1.3.6.1.4.1.6141.2.60.28.1.1.30.1.2 | EtherType | read-create | This object represent the Ethertype that will be stamped on the frame on egress and removed on ingress. |
| ROW wwpLeosVplsVirtualSwitchEtypeTranslationRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.30.1.3 | RowStatus | read-create | This object can be set to 'createandgo' to add entry in the table. This object can be set to 'destroy' to delete entry in the table. Refer to description of table entry to see how to create entries in the table. |
| wwpLeosVplsTunnelPairTable | 1.3.6.1.4.1.6141.2.60.28.1.1.31 | not-accessible | This table allows creating tunnel pairs. Having a tunnel pair will force the device to accept pbt encapsulated frames on given pair of tunnels ports and not on any port. This table is only accessible in PBT mode. | |
| wwpLeosVplsTunnelPairEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.31.1 | not-accessible | Each entry contains the tunnel pair. | |
| INT wwpLeosVplsTunnelPairIndx | 1.3.6.1.4.1.6141.2.60.28.1.1.31.1.1 | INTEGER | not-accessible | This object represent the index in the table. |
| STR wwpLeosVplsTunnelPairName | 1.3.6.1.4.1.6141.2.60.28.1.1.31.1.2 | DisplayString | read-create | This object represent the name of the pair and must be unique. This object cannot be modified once entry is created. |
| I32 wwpLeosVplsTunnelPairEncapTunnelIndx | 1.3.6.1.4.1.6141.2.60.28.1.1.31.1.3 | Integer32 | read-create | This object represent the encap tunnel that is part of this tunnel pair. This tunnel index should be valid and must exist in wwpLeosVplsEncapTunnelTable. This object cannot be modified once entry is created. |
| I32 wwpLeosVplsTunnelPairDecapTunnelIndx | 1.3.6.1.4.1.6141.2.60.28.1.1.31.1.4 | Integer32 | read-create | This object represent the decap tunnel that is part of this tunnel pair. This tunnel index should be valid and must exist in wwpLeosVplsDecapTunnelTable. This object cannot be modified once entry is created. |
| ROW wwpLeosVplsTunnelPairRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.31.1.5 | RowStatus | read-create | This object can be set to 'createandgo' to add entry in the table. This object can be set to 'destroy' to delete entry in the table. Refer to description of table entry to see how to create entries in the table. |
| wwpLeosVplsVirtualSwitchMplsEvplMemberTable | 1.3.6.1.4.1.6141.2.60.28.1.1.32 | not-accessible | This table is used to create mpls virtual switch subscriber port-vlan membership entry. | |
| wwpLeosVplsVirtualSwitchMplsEvplMemberEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.32.1 | not-accessible | This entry corresponds to single port-vlan subscriber entry in wwpLeosVplsVirtualSwitchMplsEvplMemberTable table. | |
| INT wwpLeosVplsVirtualSwitchMplsEvplMemberPortId | 1.3.6.1.4.1.6141.2.60.28.1.1.32.1.1 | INTEGER | read-create | This object specifies the port number which is to be added as a customer facing port for the mpls virtual switch index wwpLeosVplsVirtualSwitchMplsIndx. |
| INT wwpLeosVplsVirtualSwitchMplsEvplMemberVlanId | 1.3.6.1.4.1.6141.2.60.28.1.1.32.1.2 | INTEGER | read-create | This object specifies the subscriber vlan attached to this mpls virtual switch index wwpLeosVplsVirtualSwitchMplsIndx. This object cannot be modified once entry is created in this table. This object can only be specified when creating entries in this table. |
| ROW wwpLeosVplsVirtualSwitchMplsEvplMemberRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.32.1.3 | RowStatus | read-create | Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. To delete a row in this table, a manager must set this object to 'destroy'. If the entry exists, it will be displayed as 'active'. |
| INT wwpLeosVplsVirtualSwitchMplsEvplMemberEncapCosPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.32.1.4 | INTEGER | read-write | This object specifies the ingress cos policy for given EVPL entry. |
| INT wwpLeosVplsVirtualSwitchMplsEvplMemberEncapFixedDot1dPri | 1.3.6.1.4.1.6141.2.60.28.1.1.32.1.5 | INTEGER | read-write | This object specifies the ingress fixed cos attributes for given member entry. This attribute is only valid when the EncapCosPolicy is set to 'fixed' |
| INT wwpLeosVplsVirtualSwitchMplsEvplMemberSubscriberDot1dPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.32.1.6 | INTEGER | read-write | This object configures the member policy used to decide if the subscriber frame's 'c-vlan' .1d priorty should be left alone 'leave', or remarked 'provider-inherit' to the resolved provider 's-vlan' priority. This attribute is valid when the member's SubscriberDot1Policy is 'leave' or 'provider-inherit'. If stt to 'inheritVs' the attribute is inherited from the parent virtual-switch |
| wwpLeosVplsVirtualSwitchMplsEvplMemberStatsTable | 1.3.6.1.4.1.6141.2.60.28.1.1.33 | not-accessible | The (conceptual) table listing the virtual switch member stats table. | |
| wwpLeosVplsVirtualSwitchMplsEvplMemberStatsEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.33.1 | not-accessible | The virtual switch member stats table entry index by wwpLeosVplsVirtualSwitchMplsIndx, wwpLeosVplsVirtualSwitchMplsMemberPortId and VlanId. | |
| C32 wwpLeosVplsVirtualSwitchMplsEvplMemberRxBytesHi | 1.3.6.1.4.1.6141.2.60.28.1.1.33.1.1 | Counter32 | read-only | This represents the total number of higher 32 bits received for given mpls virtual switch member port. |
| C32 wwpLeosVplsVirtualSwitchMplsEvplMemberRxBytesLo | 1.3.6.1.4.1.6141.2.60.28.1.1.33.1.2 | Counter32 | read-only | This represents the total number of lower 32 bits received for given virtual switch member port. |
| wwpLeosVplsVirtualSwitchEthEvplMemberTable | 1.3.6.1.4.1.6141.2.60.28.1.1.34 | not-accessible | This table is used to create virtual switch membership entry. | |
| wwpLeosVplsVirtualSwitchEthEvplMemberEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.34.1 | not-accessible | This entry corresponds to single entry in wwpLeosVplsVirtualSwitchEthernetEvplMemberTable table. | |
| INT wwpLeosVplsVirtualSwitchEthEvplMemberPortId | 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.1 | INTEGER | read-only | This object specifies the port id associated with wwpLeosVplsVirtualSwitchEthIndx. |
| INT wwpLeosVplsVirtualSwitchEthEvplMemberVlan | 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.2 | INTEGER | read-create | This object specifies the subscriber vlan attached to this eth virtual switch index wwpLeosVplsVirtualSwitchEthIndx. This object cannot be modified one entry is created. This object can only be specified when entry is created in this table. |
| ROW wwpLeosVplsVirtualSwitchEthEvplMemberRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.3 | RowStatus | read-create | This object can be set to 'createandgo' to add entry in the table. This object can be set to 'destroy' to delete entry in the table. Refer to description of table entry to see how to create entries in the table. |
| INT wwpLeosVplsVirtualSwitchEthEvplMemberEncapCosPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.4 | INTEGER | read-write | This object specifies the ingress cos policy for given EVPL entry. |
| INT wwpLeosVplsVirtualSwitchEthEvplMemberEncapFixedDot1dPri | 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.5 | INTEGER | read-write | This object specifies the ingress fixed cos attributes for given member entry. This attribute is only valid when the EncapCosPolicy is set to 'fixed' |
| INT wwpLeosVplsVirtualSwitchEthEvplMemberSubscriberDot1dPolicy | 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.6 | INTEGER | read-write | This object configures the member policy used to decide if the subscriber frame's 'c-vlan' .1d priorty should be left alone 'leave', or remarked 'provider-inherit' to the resolved provider 's-vlan' priority. This attribute is valid when the member's SubscriberDot1Policy is 'leave' or 'provider-inherit'. If stt to 'inheritVs' the attribute is inherited from the parent virtual-switch |
| INT wwpLeosVplsVirtualSwitchEthEvplMemberTranslateTag | 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.7 | INTEGER | read-create | Subscriber VLAN translate stamp. |
| INT wwpLeosVplsVirtualSwitchEthEvplMemberServiceVlanTpid | 1.3.6.1.4.1.6141.2.60.28.1.1.34.1.8 | INTEGER | read-create | This object specifies the service VLAN TPID.It is currently only applicable for VS instances associated with an MPLS enabled VS |
| wwpLeosVplsVirtualSwitchEthEvplMemberStatsTable | 1.3.6.1.4.1.6141.2.60.28.1.1.35 | not-accessible | The (conceptual) table listing the virtual switch member stats table. | |
| wwpLeosVplsVirtualSwitchEthEvplMemberStatsEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.35.1 | not-accessible | The virtual switch member stats table entry index by wwpLeosVplsVirtualSwitchEthIndx, wwpLeosVplsVirtualSwitchEthMemberPortId and VlanId. | |
| C32 wwpLeosVplsVirtualSwitchEthEvplMemberRxBytesHi | 1.3.6.1.4.1.6141.2.60.28.1.1.35.1.1 | Counter32 | read-only | This represents the total number of higher 32 bits received for given virtual switch member port. |
| C32 wwpLeosVplsVirtualSwitchEthEvplMemberRxBytesLo | 1.3.6.1.4.1.6141.2.60.28.1.1.35.1.2 | Counter32 | read-only | This represents the total number of lower 32 bits received for given virtual switch member port. |
| wwpLeosVplsVirtualCircuitEthTotalStatsTable | 1.3.6.1.4.1.6141.2.60.28.1.1.36 | not-accessible | The (conceptual) table listing the virtual circuit stats table. | |
| wwpLeosVplsVirtualCircuitEthTotalStatsEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.36.1 | not-accessible | The ethernet virtual circuit stats table entry index by wwpLeosVplsVirtualCircuitMplsIndex. | |
| C32 wwpLeosVplsVirtualCircuitEthTotalTxBytesHi | 1.3.6.1.4.1.6141.2.60.28.1.1.36.1.1 | Counter32 | read-only | This represents the total number of higher 32 bits transmitted for given virtual circuit. |
| C32 wwpLeosVplsVirtualCircuitEthTotalTxBytesLo | 1.3.6.1.4.1.6141.2.60.28.1.1.36.1.2 | Counter32 | read-only | This represents the total number of lower 32 bits transmitted for given virtual circuit. |
| C32 wwpLeosVplsVirtualCircuitEthTotalRxBytesHi | 1.3.6.1.4.1.6141.2.60.28.1.1.36.1.3 | Counter32 | read-only | This represents the total number of higher 32 bits received for given virtual circuit. |
| C32 wwpLeosVplsVirtualCircuitEthTotalRxBytesLo | 1.3.6.1.4.1.6141.2.60.28.1.1.36.1.4 | Counter32 | read-only | This represents the total number of lower 32 bits received for given virtual circuit. |
| wwpLeosVplsVirtualCircuitMplsTotalStatsTable | 1.3.6.1.4.1.6141.2.60.28.1.1.37 | not-accessible | The (conceptual) table listing the mpls virtual circuit stats table. | |
| wwpLeosVplsVirtualCircuitMplsTotalStatsEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.37.1 | not-accessible | The mpls virtual circuit stats table entry index by wwpLeosVplsVirtualCircuitMplsTotalIndex. | |
| C32 wwpLeosVplsVirtualCircuitMplsTotalTxBytesHi | 1.3.6.1.4.1.6141.2.60.28.1.1.37.1.1 | Counter32 | read-only | This represents the total number of higher 32 bits transmitted for given virtual circuit. |
| C32 wwpLeosVplsVirtualCircuitMplsTotalTxBytesLo | 1.3.6.1.4.1.6141.2.60.28.1.1.37.1.2 | Counter32 | read-only | This represents the total number of lower 32 bits transmitted for given virtual circuit. |
| C32 wwpLeosVplsVirtualCircuitMplsTotalRxBytesHi | 1.3.6.1.4.1.6141.2.60.28.1.1.37.1.3 | Counter32 | read-only | This represents the total number of higher 32 bits received for given mpls virtual circuit. |
| C32 wwpLeosVplsVirtualCircuitMplsTotalRxBytesLo | 1.3.6.1.4.1.6141.2.60.28.1.1.37.1.4 | Counter32 | read-only | This represents the total number of lower 32 bits received for given virtual circuit. |
| wwpLeosVplsVirtualSwitchEthL2CftProtocolTable | 1.3.6.1.4.1.6141.2.60.28.1.1.49 | not-accessible | Table of Virtual Switch L2 CFT protocols. | |
| wwpLeosVplsVirtualSwitchEthL2CftProtocolEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.49.1 | not-accessible | Virtual Switch L2CFT protocol entry in the Virtual Switch L2CFT Protocol Table. | |
| INT wwpLeosVplsVirtualSwitchEthL2CftProtocolType | 1.3.6.1.4.1.6141.2.60.28.1.1.49.1.1 | INTEGER | not-accessible | This object specifies a unique protocol type-index into the table. |
| INT wwpLeosVplsVirtualSwitchEthL2CftProtocolDisposition | 1.3.6.1.4.1.6141.2.60.28.1.1.49.1.2 | INTEGER | read-create | This object specifies the virtual switch L2 CFT protocol action. May forward or drop frames that match this protocol at the virtual switch + RLAN layer |
| ROW wwpLeosVplsVirtualSwitchEthL2CftProtocolRowStatus | 1.3.6.1.4.1.6141.2.60.28.1.1.49.1.64 | RowStatus | read-create | To create a row in this table, a manager must set this object to 'createAndGo'. To delete the entry set this to destroy. To update this entry this object may not be set. |
| wwpLeosVplsVirtualSwitchCFTProtoStatsTable | 1.3.6.1.4.1.6141.2.60.28.1.1.50 | not-accessible | The (conceptual) table listing the l2 control frame protocol stats for a given vlan. | |
| wwpLeosVplsVirtualSwitchCFTProtoStatsEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.50.1 | not-accessible | The layer 2 control frame protocol stats entry for the vlan. | |
| INT wwpLeosVplsVirtualSwitchCFTProtoStatsEntryVirtualSwitchIndx | 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.1 | INTEGER | read-only | This object specifies the virtual switch index which is used as unique index in the table. |
| C32 wwpLeosVplsVirtualSwitchCFTProtol2RxPkts | 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.2 | Counter32 | read-only | Specifies number of packets ingressed matching protocol. |
| C32 wwpLeosVplsVirtualSwitchCFTProtol2TunneledPkts | 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.3 | Counter32 | read-only | Specifies the number of packets that were made tunneled. |
| C32 wwpLeosVplsVirtualSwitchCFTProtol2PeerPkts | 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.4 | Counter32 | read-only | Specifies the number of peered packets. |
| C32 wwpLeosVplsVirtualSwitchCFTProtol2DiscardedPkts | 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.5 | Counter32 | read-only | Specifies the number of discarded packets. |
| C32 wwpLeosVplsVirtualSwitchCFTProtol2DecodedPkts | 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.6 | Counter32 | read-only | Specifies the number of packets that came in tunneled and then restored. |
| C32 wwpLeosVplsVirtualSwitchCFTProtol2DecodedFailures | 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.7 | Counter32 | read-only | Specifies the number of packets that failed to 'untunnel'. |
| C32 wwpLeosVplsVirtualSwitchCFTProtol2TunneledSubcriberPortPkts | 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.8 | Counter32 | read-only | Specifies the number of tunneled packets received on subscriber port.. |
| INT wwpLeosVplsVirtualSwitchCFTProtol2ProtocolNum | 1.3.6.1.4.1.6141.2.60.28.1.1.50.1.9 | INTEGER | read-only | This object represent the list of protocols supported by the device. |
| wwpLeosVplsVirtualSwitchCFTProtoTotalStatsTable | 1.3.6.1.4.1.6141.2.60.28.1.1.51 | not-accessible | The (conceptual) table listing the l2 control frame protocol stats for a given vlan. | |
| wwpLeosVplsVirtualSwitchCFTProtoTotalStatsEntry | 1.3.6.1.4.1.6141.2.60.28.1.1.51.1 | not-accessible | The layer 2 control frame protocol stats entry for the vlan. | |
| INT wwpLeosVplsVirtualSwitchCFTProtoTotalStatsEntryVirtualSwitchIndx | 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.1 | INTEGER | read-only | This object specifies the virtual switch index which is used as unique index in the table. |
| C32 wwpLeosVplsVirtualSwitchCFTProtoTotall2RxPkts | 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.2 | Counter32 | read-only | Specifies number of packets ingressed matching protocol. |
| C32 wwpLeosVplsVirtualSwitchCFTProtoTotall2TunneledPkts | 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.3 | Counter32 | read-only | Specifies the number of packets that were made tunneled. |
| C32 wwpLeosVplsVirtualSwitchCFTProtoTotall2PeerPkts | 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.4 | Counter32 | read-only | Specifies the number of peered packets. |
| C32 wwpLeosVplsVirtualSwitchCFTProtoTotall2DiscardedPkts | 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.5 | Counter32 | read-only | Specifies the number of discarded packets. |
| C32 wwpLeosVplsVirtualSwitchCFTProtoTotall2DecodedPkts | 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.6 | Counter32 | read-only | Specifies the number of packets that came in tunneled and then restored. |
| C32 wwpLeosVplsVirtualSwitchCFTProtoTotall2DecodedFailures | 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.7 | Counter32 | read-only | Specifies the number of packets that failed to 'untunnel'. |
| C32 wwpLeosVplsVirtualSwitchCFTProtoTotall2TunneledSubcriberPortPkts | 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.8 | Counter32 | read-only | Specifies the number of tunneled packets received on subscriber port.. |
| INT wwpLeosVplsVirtualSwitchCFTProtoTotall2ProtocolNum | 1.3.6.1.4.1.6141.2.60.28.1.1.51.1.9 | INTEGER | read-only | This object represent the list of protocols supported by the device. |
| wwpLeosVplsMIBNotificationPrefix | 1.3.6.1.4.1.6141.2.60.28.2 | |||
| wwpLeosVplsMIBNotifications | 1.3.6.1.4.1.6141.2.60.28.2.0 | |||
| wwpLeosVplsMIBConformance | 1.3.6.1.4.1.6141.2.60.28.3 | |||
| wwpLeosVplsMIBCompliances | 1.3.6.1.4.1.6141.2.60.28.3.1 | |||
| wwpLeosVplsMIBGroups | 1.3.6.1.4.1.6141.2.60.28.3.2 |
RFC description
Ciena VPLS virtual private LAN service MIB for managing Ethernet virtual circuits and switches.
Start monitoring Ciena/WWP LEOS-based Ethernet switches, VPLS provider edge nodes (pseudowire-binding/MAC-table/VLAN-tag status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.