WWP-LEOS-BLADE-MIB

All MIBs › WWP-LEOS-BLADE-MIB

Organization: Ciena, Inc

Last Updated: 2011-10-19

Category: Ciena LEOS Carrier Ethernet

Description: Monitors Ciena LEOS chassis blade module inventory, operational status, and hardware version information.

Start monitoring vendor-neutral, standards-based MIB, any SNMPv3-capable network device (SNMP engine identity/boot/clock status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

What Is WWP-LEOS-BLADE-MIB?

WWP-LEOS-BLADE-MIB is a Ciena (formerly World Wide Packets, LEOS operating system) enterprise MIB monitoring chassis blade module inventory, operational status, and hardware version information on modular Ciena LEOS switching platforms. It exposes per-blade identity, hardware revision, and operational/administrative state data for the field-replaceable modules within a chassis. Its monitoring emphasis is squarely hardware status: administrators can confirm each blade slot is populated with the expected module type and hardware version, and detect a blade that has gone offline, failed, or been removed, which is critical for chassis-based platforms where blade failure directly impacts port capacity. It likely works alongside the standard ENTITY-MIB for generic physical-entity inventory, layering LEOS-specific blade detail on top. It is deployed on Ciena/World Wide Packets LEOS chassis-based Carrier Ethernet switches in service-provider and enterprise aggregation networks, where WWP-LEOS-BLADE-MIB SNMP monitoring flags a failed or unseated blade before it affects port capacity.

IPNetwork Monitor allows you to monitor SNMP objects defined in WWP-LEOS-BLADE-MIB. Use the built-in SNMP Monitoring Browser to explore available variables, view their current values and descriptions, and select the objects you want to monitor. You can then create SNMP monitors, configure thresholds, and receive alerts when monitored values change.

Supported Devices

Ciena LEOS chassis switch
World Wide Packets modular Carrier Ethernet switch

Monitoring Examples

No sample objects were supplied for this module; an administrator would typically poll a per-slot blade table keyed by slot/blade index to check each blade's operational status and hardware version, with a blade transitioning to a down or absent status revealing a hardware failure or unseated module requiring replacement.

Imported Objects

From SNMPv2-SMI

MODULE-IDENTITY
NOTIFICATION-TYPE
OBJECT-TYPE
TimeTicks
Unsigned32

From SNMPv2-TC

DateAndTime
DisplayString
MacAddress
RowStatus

From WWP-SMI

wwpModulesLeos

OBJECT-IDENTITY

OIDs

OID symbolic	OID numeric	Type	Access	Description
wwpLeosBladeMIB	1.3.6.1.4.1.6141.2.60.1			Added new last reset reasons.
wwpLeosBladeMIBObjects	1.3.6.1.4.1.6141.2.60.1.1
wwpLeosBlade	1.3.6.1.4.1.6141.2.60.1.1.1
wwpLeosBladeTable	1.3.6.1.4.1.6141.2.60.1.1.1.1		not-accessible	The (conceptual) table listing the Blades configured/detected.
wwpLeosBladeEntry	1.3.6.1.4.1.6141.2.60.1.1.1.1.1		not-accessible	An entry (conceptual row) in the wwpLeosBladeTable.
INT wwpLeosBladeId	1.3.6.1.4.1.6141.2.60.1.1.1.1.1.1	INTEGER	read-only	The object indicates the unique id for the blade.
INT wwpLeosBladeType	1.3.6.1.4.1.6141.2.60.1.1.1.1.1.2	INTEGER	read-only	The object indicates whether this is a control blade, a line blade or an uplink blade.
STR wwpLeosBladeCapFilename	1.3.6.1.4.1.6141.2.60.1.1.1.1.1.3	DisplayString	read-write	The capability file name (including the path, if applicable) to be read from. This is the file describing capabilities of the blade and is required to configure un unequipped blade or to add a new blade. Length of filename string must not exceed 255 alpha-numeric characters, no spaces in filenames.
INT wwpLeosBladeAdminState	1.3.6.1.4.1.6141.2.60.1.1.1.1.1.4	INTEGER	read-write	The object indicates the desired state of the blade. The administrative state for control blades can be set to disabled only if the control blade has a functioning backup.
INT wwpLeosBladeOperState	1.3.6.1.4.1.6141.2.60.1.1.1.1.1.5	INTEGER	read-only	The object indicates the operational state of the blade. If the blade is detected and the administrative state for that blade is enabled, then the operational state of the blade is 'enabled'. If the blade is detected, but the administrative state is 'disabled', then the operational state is also 'disabled'. A faulted state occurs when a fault or communication failure is detected on a that is in either the 'enabled' or 'disabled' operation state. Any time a blade is removed, then the blade state transitions to 'unequipped'. If a new blade replaces that blade state then the state is determined by its administrative state once it is detected ('enabled' or 'disabled').
MAC wwpLeosBladeStartMacAddr	1.3.6.1.4.1.6141.2.60.1.1.1.1.1.6	MacAddress	read-only	Base MAC address for the Blade, from which the mac addresses for the ports on this blade are derived.
INT wwpLeosBladeNumPorts	1.3.6.1.4.1.6141.2.60.1.1.1.1.1.7	INTEGER	read-create	The total number of physical ports present on this Blade.
ROW wwpLeosBladeStatus	1.3.6.1.4.1.6141.2.60.1.1.1.1.1.8	RowStatus	read-create	Used to manage the creation and deletion of the conceptual rows in this table. To create a row in this table, a manager must set this object to 'createAndGo'. Object in the entry cannot be modified once the wwpLeosBladeStatus is set to 'active'.
wwpLeosPhyBladeTable	1.3.6.1.4.1.6141.2.60.1.1.1.2		not-accessible	The (conceptual) table listing the Blades detected(physically present).
wwpLeosPhyBladeEntry	1.3.6.1.4.1.6141.2.60.1.1.1.2.1		not-accessible	An entry (conceptual row) in the wwpLeosPhyBladeTable.
TIK wwpLeosPhyBladeSysUpTime	1.3.6.1.4.1.6141.2.60.1.1.1.2.1.1	TimeTicks	read-only	The time (in hundredths of a second) since the blade was last re-initialized.
STR wwpLeosPhyBladeSerialNum	1.3.6.1.4.1.6141.2.60.1.1.1.2.1.2	DisplayString	read-only	Serial number of the blade, represented as a string.
STR wwpLeosPhyBladeBoardRevision	1.3.6.1.4.1.6141.2.60.1.1.1.2.1.3	DisplayString	read-only	Module board hardware revision represented as a string.
STR wwpLeosPhyBladePostResults	1.3.6.1.4.1.6141.2.60.1.1.1.2.1.4	DisplayString	read-only	The test result string generated by the POST tests for the blade.
U32 wwpLeosPhyBladePostCode	1.3.6.1.4.1.6141.2.60.1.1.1.2.1.5	Unsigned32	read-only	The result code returned by the device POST test.
DAT wwpLeosPhyBladeMfgDate	1.3.6.1.4.1.6141.2.60.1.1.1.2.1.6	DateAndTime	read-only	The date that the blade was manufactured.
STR wwpLeosPhyBladeBoardDesc	1.3.6.1.4.1.6141.2.60.1.1.1.2.1.7	DisplayString	read-only	Board Description for the blade.
U32 wwpLeosPhyBladeNumResets	1.3.6.1.4.1.6141.2.60.1.1.1.2.1.8	Unsigned32	read-only	This object defines the number of times that the blade has been restarted.
INT wwpLeosPhyBladeLastRebootReason	1.3.6.1.4.1.6141.2.60.1.1.1.2.1.9	INTEGER	read-only	Indicates the reason for the last reboot.
INT wwpLeosPhyBladeRebootOperation	1.3.6.1.4.1.6141.2.60.1.1.1.2.1.10	INTEGER	read-write	Writing one of the specified values to this field causes the specified type of reboot to occur. none is the value returned when this leaf is queried. writing this value to the leaf will have no effect. 'reboot' option causes the system to reboot and restart using its current configuration. 'rebootReinit' option causes the module to erase all user configuration data and reset to factory default settings. 'rebootCustReinit' option causes the module to replace the current configuration with a customer supplied default, then reboot.
wwpLeosBladeMIBNotificationPrefix	1.3.6.1.4.1.6141.2.60.1.2
wwpLeosBladeMIBNotifications	1.3.6.1.4.1.6141.2.60.1.2.0
NTF wwpLeosBladeStateChange	1.3.6.1.4.1.6141.2.60.1.2.0.1			A wwpLeosPhyBladeUpDown notification is sent whenever the operational state of the blade is changed.
NTF wwpLeosBladePostFail	1.3.6.1.4.1.6141.2.60.1.2.0.2			A wwpLeosBladePostFail notification is sent if the blade post tests are failed.
wwpLeosBladeMIBConformance	1.3.6.1.4.1.6141.2.60.1.3
wwpLeosBladeMIBCompliances	1.3.6.1.4.1.6141.2.60.1.3.1
wwpLeosBladeMIBGroups	1.3.6.1.4.1.6141.2.60.1.3.2

RFC description

Ciena LEOS blade MIB managing blade configuration, status, and reset reasons on optical network platforms.

Start monitoring Ciena LEOS chassis switch, World Wide Packets modular Carrier Ethernet switch (per-blade hardware-version/oper-state status) with a free 30-day trial of IPNetwork Monitor. Import MIBs, browse SNMP OIDs, create custom SNMP monitors, configure alerts, and monitor any SNMP-enabled network device from a single console.

Download WWP-LEOS-BLADE-MIB

What Is WWP-LEOS-BLADE-MIB?

Supported Devices

Monitoring Examples

This MIB depends on

Related MIBs

RFC description